02 Iris1 [PDF]

Zitiervorschau

SIGMA Standard

Name Code Application

IRIS NV Elevator Maintenance OEMS-P1-111-000 Service Business Dept.

Rev. Date

Rev. No. Page

2011.02.25 0 33/N

Control box 3.2.1

Daily inspection items and standards - - - - - - - - - - - - - - - - - - - - - - - - - - -

3.2.2

Control box MCCB

---------------------------------------

38

3.2.3

Determine voltage and fuse - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -

38

3.2.4

Insulation measuring and earthing- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -

39

3.2.5

Electronic contactor

---------------------------------------

40

3.2.6

PCB base board

---------------------------------------

41

1) 2) 3) 4) 5) 6) 7) 8)

--------------------------------------Synchromotor PG card - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - SM.02/1 PCB(TOC Controller Board) - - - - - - - - - - - - - - - - - - - - - - - - - - - SM.02/G PCB --------------------------------------SM-03 PCB(Car Call Board) - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - SM.04V 12/A(Call & Display Control Board) - - - - - - - - - - - - - - - - - - - - - SM.04V 12/A --------------------------------------BST Door Controller - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - Main PCB

34

41 46 47 49 50 51 52 53

3.2.7

Transformer

---------------------------------------

54

3.2.8

Regeneration resistance- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -

54

2005.12.27. Approval

SIGMA Standard 3.2

Name Code Application

IRIS NV Elevator Maintenance OEMS-P1-111-000 Service Business Dept.

Rev. Date

Rev. No. Page

2011.02.25 0 34/N

Control box

The manual mainly introduces content about IRIS NV elevator maintenance work only. Therefore, the manual does not include detailed technology details, please refer to STEP control box manual.

Notice 

When check the control box, cut off the power supply; after performing Lock Out /Tag Out, conduct work.



Please determine whether plastic cap is covered on the terminal. If cap is not covered on its top, please make cap cover the top.



If power supply is 200V or 400V, please affix marking label to make others take care.



If PCB is applied, it should be avoided that PCB is scratched by protruded pin at back.



If INV elevator type is applied, after cutting off power supply, smoothing condenser is still in charging state; therefore, please determine whether DC voltage on capacitor two ends conduct working after discharging completely.

3.2.1 Daily inspection items and standards Inspection Part

Inspection item

Tool

State/standard circle Ambient temperature:

Operating environment

Ambient temperature, moisture, vibration, dust, corrosive gas, oil, dust, dribbles etc.

Naked eyes,

lower than 40℃,

thermometer,

accord with moisture

hygrometer

etc. environment

1 month

requirements

LCD indicating

Whether danger exists around the assembly

Naked eyes

No dangerous item

1 month

Whether LCD indicating is normal

Naked eyes

Indicating is normal

1 month

Bolts relaxation is not allowed.

Naked eyes,

No abnormal condition

terminal

Connector relaxation is not allowed.

screwdriver

Assemble is stable

Bolts and tail

Determine whether protective layer cracks

Naked eyes

No abnormal condition

cord

or discolors

Connector

2005.12.27. Approval

1 month 1 month

SIGMA Standard

Name Code Application

IRIS NV Elevator Maintenance OEMS-P1-111-000 Service Business Dept.

Rev. Date

Rev. No. Page

2011.02.25 0 35/N

Determine whether earthing panel deforms. Electromagne

Whether there is vibration noise in working

Naked eyes,

None

acoustic Contact attraction state of contact point

Noise occurs at

sensation

contacting point

Determine liquid leakage, discolor, crack,

Naked eyes

No abnormal condition

tic contactor, relay

Electrolytic capacitor

case expansion conditions

1 month

1 month

Determine whether safety liquid flows out, and whether case expanses

Capacitor

Determine whether there is dust

cooling fan

Naked eyes,

No abnormal condition

1 month

Normal rotation

1 month

No abnormal condition

1 month

hands Determine whether the fan conduct air

Naked eyes

exchanging and determine its fixing state Control box,

Whether there is abnormal noise

Acoustic

cooling fan

(after cutting off the power supply, conduct

sensation,

determination by rotating fan vane

naked eyes,

manually)

hands

Whether there is abnormal vibration

Naked eyes

Whether discoloring condition occurs for

Naked eyes,

over-high temperature.

smell

Determine connecting state between control

Naked eyes

No abnormal condition

1 month

PCB discoloring and abnormal odor

Naked eyes,

No abnormal condition

1 month

PCB crack, damage, deformation

smell

Connector

box and connector, and state of dust & foreign adhesive matter PCB

(1)

Num of electric wire connected on a terminal is 2 strands, and num of both sides is less than 4 strands. And it is not allowed that the current is higher than maximum permissible current of the terminal.

(2)

Slightly draw the electric wire to determine fastening state and connecting state of jack.

(3)

Leave electric wire long enough for conditions of contact moving, or cover opening for fault handle or inspecting etc..

(4)

Figure 2-1 is outline drawing of control box (for function description, please refer to STEP control box manual).

2005.12.27. Approval

Name Code

SIGMA Standard

Application

IRIS NV Elevator Maintenance OEMS-P1-111-000 Service Business Dept.

Rev. Date

Rev. No. Page

2011.02.25 0 36/N

Figure 2-1. Outline drawing of control box

Function of each Part

No.

Section

1

Part1

2 3 4

Part2

Part3

Part Name

Function

RR resistance

Consume regenerated electric power

DZ1

Brake resistance

SMPS ERO

Main board & Hall communication wire power supply [input 220V, output 24V] Buttons used for low-speed operation [Up, Com, Down, NOR/INS, E.STOP]

5

FU1

Fuse [110V safety chain, capacity:2A]

6

FU2

Fuse [Brake voltage, capacity:4A]

7

FU3

Fuse [Door & car door power supply, capacity:2A]

8

FSK2

Break [hoistway lighting switch]

9

CP1

Break [SMPS power supply input terminal]

10

Part4

KAD

11

FR

13

FIRE2

2005.12.27. Approval

Safety chain[landing door, KAD contactor will be “on” when landing door is closed] Fire Return contactor [contactor will be “on” when hall switch is on] The 2nd fire-fighting operation contactor [the contactor will be on when the 2nd fire-fighting switch is on]

SIGMA Standard 14 15

Part5

16 17

Part6

Name Code Application

IRIS NV Elevator Maintenance OEMS-P1-111-000 Service Business Dept.

Rev. Date

Rev. No. Page

ERO

ERO switch

DZL

Door Zone Lamp[used for rescue operation]

BY

Brake relay [it will be “on” when starts]

KMZ

2011.02.25 0 37/N

Similar with relay C1ST, it could be started in opening state only]

18

UCM1

Door-opening car-departure [in normal: on, when start: off]

19

UCM2

Door-opening car-departure [in normal: on, when start: off]

20

FIRE1

Relay for the 1st fire-fighting operation

21

GOV

22

Part7

Field panel

23

Part8

TB

Speed governor relay [it is on when speed governor safety chain is enabled] Terminals used for wire connecting of external apparatus of control box Terminal block[used for wire connecting of control box] Transformer [used for supply power for control box (single

24

Part9

Trans

phase), input power supply is 380V, output power supply is 110V Supply for [FU1], 123V[FU2], 220V[FU3]

25

OCB

26

SW Part10

Break of main power supply [380V] Contactor [similar with C1SW, could be started under the state of being enabled only]

27

FSK1

Break used for lighting power supply

28

APD

EMI filter

29

TB

Terminal block

30

Main board

Drive board

PG Card

Rotary Encoder

31

Part11

Integrated

32

(5)

driver

IPM

When connect 2 strands of electric wire end terminal to another, keep maximum contact face between terminals. Please not make wire connecting angle become higher than 60˚.

2005.12.27. Approval

SIGMA Standard

Name Code Application

IRIS NV Elevator Maintenance OEMS-P1-111-000 Service Business Dept.

Rev. Date

Rev. No. Page

60˚

Figure 2-2. Connecting method of connecting terminal

.

2005.12.27. Approval

2011.02.25 0 38/N

SIGMA Standard 3.2.2

IRIS NV Elevator Maintenance OEMS-P1-111-000 Service Business Dept.

Name Code Application

Rev. Date

Rev. No. Page

2011.02.25 0 39/N

Control box MCCB (OCB) Inspection

Part

Inspection item

Tool

State/standard circle

Voltage regulation [V]

Voltmeter

Unparallel voltage [V] Control box MCCB

(1)

-15 ~+10%

1 month

±10%

1 month

Apparatus surface heats up

Surface thermometer

1 month

Terminal is screw up and conduct wiring

Screwdriver

1 month

If fault is related to input power supply, please inspect following content. 1) The 1st side: ⓐ R-S,

ⓑ R-T,

ⓒ S-T

nd

2) The 2 side: ⓓ R1-S1, ⓔ R1-T1, ⓕ S1-T1 If measured voltage (ⓐ) of the 1st side and measured voltage (ⓓ) of the 2nd side are higher than 2% of service voltage, cut off MCCB of building distributor box, and measure resistance between R-R1 after opening control box MCCB, measuring result should be 0[Ω] or near to 0[Ω]. (2)

Measure rest S, T phase with method same with the one for R mentioned above. If there is abnormal condition, please conduct accurate inspection and takes measures (replacing) according to inspection results.

(3)

Measure peak (p.m. 3~4 o’clock, 8~9 o’clock) voltage in each summer and ordinary (a.m.) voltage, and record measuring results on the daily inspection record.

(4)

After cutting off the power supply and implementing Lock Out / Tag Out, inspect whether MCCB surface discolors; and determine whether its temperature is normal after measuring the temperature.

(5) 3.2.3

Please determine whether there is abnormal noise or vibration inside MCCB. Determine voltage and fuse Inspection

Part

Inspection item

Tool

State/standard circle

Measure voltage and confirm fuse

Each control/signal wire

Voltmeter

Refer to field drawing

1 month

Rated capacity and contact state

Naked eyes

Refer to field drawing

1 month

(1) Confirm voltage and fuse capacity of each control/signal wire. (2)

Confirm fuse connecting state and fastening state of terminals with hands.

2005.12.27. Approval

Name Code

SIGMA Standard 3.2.4

Application

IRIS NV Elevator Maintenance OEMS-P1-111-000 Service Business Dept.

2011.02.25 0 40/N

Rev. Date

Rev. No. Page

Insulation measuring and earthing Inspection

Part

Inspection item

Tool

State/standard circle

nd

The 2 side face of control box Insulation

Each control/signal wire Fastening state of terminals on specified position

Earthing

(1)

Insulation resistance meter

1㏁

Screwdriver

Fastening

0.5 ㏁

12 months

1 month

Working overview Resistance property of insulator is insulation. Measure property of this insulation to prevent electric shock accident and defective insulation to protect apparatus and avoid safety accident coursed by abnormal action of elevator.

(2)

Electric shock preventing 1) DC voltage straightly through main circuit of frequency converter, even though the MCCB is turned off, voltage charged by the capacitor can not be discharged completely at once. Thus, please pay much attention to safety issue. And capacitor (AL electrolytic capacitor) connects with main circuit, even though the MCCB is turned off, voltage charged by the capacitor can not be discharged completely and immediately. Therefore, please adopt tester to determine whether DC voltage is 0~10VDC before working. 2) Please must implement insulation test before measuring the insulation to prevent PCB from being damaged. There are semiconductor elements used in the circuit, therefore, elements will be damaged if integrated circuit is earthed. Thus, please adopt insulation resistance tester (generation voltage 15V) or digital integrated electricity meter to conduct insulation test on all connector terminal in the control box.

(3) Please determine connecting control box earthing. (4)

For detailed insulation measuring methods, please refer to “Sigma Elevator Test-Run Adjust Manual”.

(5)

Regulated value of insulation resistance Circuit name

Measured part

Regulated value

Main circuit

Power supply terminal (TERM1) Frame

2005.12.27. Approval

between

~ Higher than1.0[㏁]

SIGMA Standard

Name Code Application

IRIS NV Elevator Maintenance OEMS-P1-111-000 Service Business Dept.

2011.02.25 0 41/N

Rev. Date

Rev. No. Page

Motor circuit

Motor terminal (TERM2) between

Control circuit

The 2nd contact point of MCCB used for lighting Higher between

~ Frame

~ Frame

than

0.5[㏁]

The 2nd main contact point of main contactor between (6)

~ Frame

Connect earthing wire on one side of building to specific position. If connect the earthing wire to other position, control part may be can not be protected for interference from external reasons.

3.2.5

Electronic contactor Inspection

Part

Inspection item

Tool

State/standard circle

Contactor

Excess space for fixing and wiring, fasten the terminal

Naked eyes, screwdriver

1 month

Abnormal abrasion, dusting, electric arc, changeable tension force of contact point

Naked eyes, multimeter

1 month

(1)

Please determine whether electric wire used for wiring has excess part.

(2)

Please determine whether changeable tension device could be started smoothly.

(3)

Please determine whether there is serious arc trace occurs for abnormal abrasion (irregular abrasion) of contact point.

(4)

Please determine ON / OFF action of electronic contactor.

2005.12.27. Approval

SIGMA Standard 3.2.6

Name Code Application

IRIS NV Elevator Maintenance OEMS-P1-111-000 Service Business Dept.

Rev. Date

Rev. No. Page

2011.02.25 0 42/N

PCB base board Inspection

Part

Inspection item

Tool

State/standard circle

PCB Board

(1)

Fixing state, jack connecting state

Naked eyes, hands

1 month

Precautions for treatment and cleaning 1) Please pack PCB to prevent it from being impacted in moving. Please do not keep it in humid place for a long term. 2) After cutting of power supply and implementing Lock Out / Tag Out, please pay attention to static electricity, and conduct cleaning.

(2)

Main PCB 1) Outline.

도면 3.18 제어电路端子

2005.12.27. Approval

Name Code

SIGMA Standard

Application

IRIS NV Elevator Maintenance OEMS-P1-111-000 Service Business Dept.

Rev. Date

Rev. No. Page

2011.02.25 0 43/N

Figure 3.18 Terminal of control circuit

No

Mic name

Function

Remark

1

JP1-JP5

Low-voltage optical coupling input

2

JP6

Power supply input interface

3

JP7-JP9

CAN communication interface

4

JP10

Used for emergency condition

5

JP11

Modem supervising interface

6

JP12

Portable governor interface

7

JP13-JP16

Relay output interface

8

JP17

High-voltage optical coupling input Drawing 3.18 Terminal of control circuit

2) Switch function Switch name

No. 1

Function

Remark

On

ARM Program start ARM Normal working state DSP Program start

Setup state: OFF Note: when start program, start CPLD firstly → and set SW1 to be ON→ DSP program start→ ARM program start (start window is different) SW2 assembly state: OFF SW3/SW4 assembly state: ON

Off On

SW1 2

SW2

State

Off

DSP Normal working state

On

CAN Terminal resistance setup

Off

CAN Terminal resistance invalid

On

RS485 Terminal resistance setup

Off

RS485 Terminal resistance invalid

SW3 SW4

SW5

2005.12.27. Approval

assembly state: ON

SIGMA Standard

Name Code Application

IRIS NV Elevator Maintenance OEMS-P1-111-000 Service Business Dept.

Rev. Date

Rev. No. Page

2011.02.25 0 44/N

3) MIC name and function description.

Mic

Connected

name

Wire num

JP1

JP2

JP3

JP4

2005.12.27. Approval

Name

1

X0

2

Function

Default default

X1

Auto/Inspection input signal X0 and X1 all input→automatic

3

X2

Up signal

default

4

X3

DN signal,

default

1

X4

2LS(SDS1U)

close

2

X5

1LS(SDS1D)

close

3

X6

4LS(SDS2U)

close

4

X7

3LS(SDS2D)

close

5

X8

GOV CTT contact point input signal

open

6

X9

7

X10

8

X11

1

X12

UL(up limit switch)

close

2

X13

DL(down limit switch)

close

3

X14

2LV(level switch signal)

open

4

X15

1LV(level switch signal)

open

5

X16

close

6

X17

open

1

x18

Fireman(fire-hazard reset switch)

open

2

x19

Fireman Service fireman switch

open

3

x20

open

4

x21

SW CTT contact point input signal

5

x22

BY CTT input signal

open

6

x23

BS1 switch signal (left)

open

7

x24

BS2 switch signal (right)

open

8

x25

MTH signal input

open

KMZ CTT contact point input signal FR CTT contact point input signal

default

open open open

open

SIGMA Standard

Name Code Application

IRIS NV Elevator Maintenance OEMS-P1-111-000 Service Business Dept.

Rev. Date

Rev. No. Page

9

x26

Earthquake signal input (EQS)

open

10

x27

ARD signal(emergency level for power failure)input

open

Name

Function

Default

1

x28

UCM1,2 CTT contact point input

open

2

x29

KAD CTT contact point input

open

3

x30

FIRE1 CTT contact point input (the 1st fire-fighting)

open

4

x31

5

COM

1

GND

2

24V

24VDC power input terminal (used for CTT input circuit)

3

GND

0VDC power input (used for CTT output circuit)

4

24V

24VDC power input (used for CTT output circuit)

Mic Connected name Wire num

JP5

JP6

FIRE2

CTT

input(the 2

nd

contact

point

fire-fighting)

X0~X31 input signal common terminal 0VDC power input terminal (used for CTT input circuit)

1 2 JP7

3 4

JP8

2005.12.27. Approval

CAN1H Tandem communication signal (TXA1+)/(TXA1-) CAN1L (Car & Hall CAN communication)

1

+24V

2

0V

3 4

JP9

2011.02.25 0 45/N

CAN2H Parallel or group-control tandem signal (TXA2+) (TXA2-) CAN2L

1

+24V

2

0V

3

CAN3H

open

SIGMA Standard

Name Code Application

4 JP10

IRIS NV Elevator Maintenance OEMS-P1-111-000 Service Business Dept.

JP12

Rev. No. Page

2011.02.25 0 46/N

CAN3L

1 MODEM

JP11

Rev. Date

1

telemonitoring

interface; ARM tandem guiding window Could be connected with RS232 interface portable governor; DSP

1

tandem guiding window

Mic name

JP13

JP14

JP15

2005.12.27. Approval

Connected Wire num

Name

1

Y14B

Output

2

Y14A

Output

3

COM6

Output

4

Y15B

Fire-fighting reset indicating

Output

5

Y15A

Fire-fighting reset indicating

Output

6

COM7

Fire-fighting reset output relay Y15 common terminals

Output

1

Y8

FIRE1 CTT output terminal

Output

2

Y9

FIRE2 CTT output terminal

Output

3

Y10

UCM1,2 CTT output terminal

Output

4

Y11

DZI Lamp output terminal

Output

5

COM4

6

Y12

Output

7

Y13

Output

8

COM5

1

Y4

2

Y5

3

COM2

4

Y6

Output

5

Y7

Output

Function

Default

Output relay Y8-Y11 common terminals

FR CTT output terminal

Output Output

Output relay Y4-Y5 common terminals

SIGMA Standard

Name Code Application

JP16

JP17

IRIS NV Elevator Maintenance OEMS-P1-111-000 Service Business Dept. COM3

1

Y0

BY CTT output

Output

2

Y1

KMZ CTT output

Output

3

Y2

4

Y3

5

COM1

Output relay Y0-Y3 common terminals

1

X32

Used for inspecting abnormal conditions of safety circuit

2

X33

Used for inspecting abnormal In-put conditions of landing door circuit

3

X34

Used for inspecting abnormal conditions of CAR door circuit

4

X35

5

COM

Synchromotor PG card Input function of processing encoder 1) Outline

Control box interface

PG card frequency resolution output interface

UVW encoder signal input interface

2005.12.27. Approval

Rev. No. Page

2011.02.25 0 47/N

6

JP25

(3)

Rev. Date

Output SW CTT output

Output

In-put

In-put In-put

X32-X35 input signal common terminal 0V CPLD program JTAG guiding window

IRIS NV Elevator Maintenance OEMS-P1-111-000 Service Business Dept.

Name Code

SIGMA Standard

Application

Rev. Date

Rev. No. Page

2011.02.25 0 48/N

2) Terminal function description

Name

Terminal No.

Terminal function description

Frequency

Frequency resolution signal start

Resolution

Collecting electrode output A,B

signal Collecting electrode output of transistor opencircuit (max. output frequency 50kHz)

Specification

Name

Terminal No.

Terminal function description

Specification

A phase signal B phase signal

Encoder differential signal input

Encoder

Z phase signal

interface, maximum frequency

input signal

U phase signal

50kHz

V phase signal W phase signal Shield earthing

Encoder power supply

(4)

+5V or+5.3V Encoder GND

Shielding field Maximum 200mA output Select S1 bridging

SM.02/1 PCB(TOC Controller Board)

Assembled on tool box, signal for output door driving and input CLS/OLS,PTM.Chime, Safety Shoe etc. signals 1) Outline

2005.12.27. Approval

SIGMA Standard JP3

JP 2

Name Code Application

IRIS NV Elevator Maintenance OEMS-P1-111-000 Service Business Dept.

JP4

JP1

JP 5

JP6

SW1,2

Rev. Date

Rev. No. Page

JP7

JP9

JP8

2) Switch function and description MIC name

Function

Remark

Used for CAN resistance setup SW1

communication

terminal

(1,2 simultaneously)

2P

(ON: terminal resistance setup, OFF: release terminal resistance)

SW2

Used for program simultaneously)

start

setup

(1,2

(On: program start, OFF: normal operation state)

2P

3) Terminal function and description MIC name JP1

Function CAN communication and power supply

Remark 4P

(1:24V，2：GND,3：CANH,4：CANL) JP2

For adding Board connecting(connecting for ex

14P

pansion) JP3

2005.12.27. Approval

Ring for floor arrival

5P

2011.02.25 0 49/N

SIGMA Standard

(5)

Name Code Application

IRIS NV Elevator Maintenance OEMS-P1-111-000 Service Business Dept.

Rev. Date

Rev. No. Page

JP4

For door drive signal output

8P

JP5

For Safety Shoe signal input

3P

JP6

For 20%, 80%, 110% Micro S/W signal input

4P

JP7

For parallel interface communication

10P

JP8

For relay output of Light/Fan driving

2P

JP9

Used for inspect load(PTM)

4P

DB1

Used for program start

9P

2011.02.25 0 50/N

SM.02/G PCB Assembled on operation panel, through main board input communication, open/close button and input ATT part signal. 1) Outline

JP1

JP5

SW1 SW3

JP3

JP2

JP7 DB1

JP6

SW2

JP4

2) Switch function and description

2005.12.27. Approval

MIC name

SW1

SW2

SW3

IRIS NV Elevator Maintenance OEMS-P1-111-000 Service Business Dept.

Name Code

SIGMA Standard

Application

Rev. Date

Rev. No. Page

Function Used for CAN communication terminal resistance setup (1,2 simultaneously) (ON: terminal resistance setup, OFF: release terminal resistance) Used for program start setup (1,2 simultaneously) (On: program start, OFF: normal operation state) 1

2

3

4

Operation panel type

On

Off

Off

Off

Main operation panel

Off

On

Off

Off

Back operation panel

Off

Off

On

Off

Operation panel for the

Off

Off

On

Server operation panel

3) Terminal function and description

MIC name JP1

JP2

JP3

Function CAN communication and power supply (1:24V, 2:GND, 3:CANH, 4:CANL) For adding Board connecting(connecting for command) For adding Board connecting(connecting for expansion)

Remark 4P

14P

14P

JP4 JP5

For ATT part switch signal input

5P

JP6

For connecting Open Button

4P

JP7

Used for Close Button

4P

DB1

For connecting program start

9P

2005.12.27. Approval

2P

2P 4P

disable Off

Remark

2011.02.25 0 51/N

Name Code

SIGMA Standard (6)

Application

IRIS NV Elevator Maintenance OEMS-P1-111-000 Service Business Dept.

Rev. Date

Rev. No. Page

2011.02.25 0 52/N

SM-03 PCB(Car Call Board) Assembled on COP and connected to SM-02/G PCB, floor button input and Lamp output. 1) Outline -connecting method of floor button and lamp

The 1st and 2nd pins are connected to lamp power supply [-] and [+] terminals respectively. The 3rd and 4th pins are connected command button terminals

2) MIC name and description

Remark Used for button connecting of F 1 car floor

Used for button connecting of F 9 car floor

Used for button connecting of F 57 car floor

Used for button connecting of F 2 car floor

Used for button connecting of F 10 car floor

Used for button connecting of F 58 car floor

Used for button connecting of F 3 car floor

Used for button connecting of F 11 car floor

Used for button connecting of F 59 car floor

Used for button connecting of F 4 car floor

Used for button connecting of F 12 car floor

Used for button connecting of F 60 car floor

Used for button connecting of F 5 car floor

Used for button connecting of F 13 car floor

Used for button connecting of F 61 car floor

Used for button connecting of F 6 car floor

Used for button connecting of F 14 car floor

Used for button connecting of F 62 car floor

Used for button connecting of F 7car floor

Used for button connecting of F 15 car floor

Used for button connecting of F 63 car floor

Used for button connecting of F 16 car floor

Used for button connecting of F 64car floor

Used for button connecting of F 8 car floor

Connector used for expansion

(7)

SM.04V 12/A (Call & Display Control Board) Assembled at hoistway of each floor, landing door calling logging and output IND signal 1) Outline

2005.12.27. Approval

SIGMA Standard

Name Code Application

IRIS NV Elevator Maintenance OEMS-P1-111-000 Service Business Dept.

2) MIC name and signal

MIC name JP1

Function Power

Remark and

CAN

4P

communication JP2

1: Output

4P

JP3

2: 24V

4P

JP4

3:GND

4P

4: Input JP5 JP6 S1

4P Used for SPI communication Used for PCB fix position

4P 2P

selecting SW1

Used for CAN communication terminal resistance setup

2005.12.27. Approval

2P

Rev. Date

Rev. No. Page

2011.02.25 0 53/N

SIGMA Standard

(8)

Name Code Application

IRIS NV Elevator Maintenance OEMS-P1-111-000 Service Business Dept.

SM.04V 12/A (Call & Display Control Board) 1) Outline

2) MIC name and description

MIC name

Function

Remark

JP1

Power and CAN communication

4P

JP2

Used for SPI communication

4P

SW1

Used for CAN communication te rminal resistance setup

2P

2005.12.27. Approval

Rev. Date

Rev. No. Page

2011.02.25 0 54/N

SIGMA Standard

(9)

Name Code Application

IRIS NV Elevator Maintenance OEMS-P1-111-000 Service Business Dept.

Rev. Date

Rev. No. Page

2011.02.25 0 55/N

BST Door Controller Assembled on upper part of car and connected to operation panel SM.02/I PCB, implement door opening/closing. 1) Outline

2) MIC name and description Function

Function

Function

Input power Earthing Signal output Signal output

Function Signal output Signal

Drive power Earthing

3) Switch function and description Switch name

Function

Open Speed

- Door Open Speed for adjust

Close

- Door Close Speed for adjust

HOLD

- HOLD Torque for adjust

OBSTruction

- OBSTruction Torque for adjust

Torque

2005.12.27. Approval

Switch name 1 2 3 4

Function ON RIGHT OFF LEFT TEST MODE ENABLE AUTO TUNE Mode Communication Choice

Name Code

SIGMA Standard

Application

IRIS NV Elevator Maintenance OEMS-P1-111-000 Service Business Dept.

2011.02.25 0 56/N

Rev. Date

Rev. No. Page

4) Function description of Push Button and LED Push Button

Function

LED

Function

TEST

Used for confirming door action

OPENED

Used

confirming

Open

finish(OLS)

state CLOSED

(Push to Check The Door) AUTO

(Push

ADJUSTMENT

Door/Auto Tune Motor)

to

Calibrate

Used for confirming Close finish, not used(CLS)

The OBSTRUCTION READ/ERROR

3.2.7

for

Two-side Shoe，used for CUT

Transformer Inspection

Part

Inspection item

Tool

State/standard circle

Transformer

Terminal/terminal relaxation, noise, he ating

Naked eye s

6 months

Wire connecting of earthing wire, cap

Naked eye s

6 months

One side of the 1st and 2nd transformer is electrified, therefore, please conduct inspe ction after cutting off power supply and implementing Lock Out /Tag Out. (1)

Please determine whether abnormal odor or over-heating state occurs.

(2)

Please determine whether there is abnormal noise.

(3)

Please determine whether Transformer bears over-load.

(4)

Please determine whether there is dust or carbon powder between terminals, adopt cleaning cloth or brush to clean up.

3.2.8

Regeneration resistance Inspection

Part

Inspection item

Tool

State/standard circle

Regeneration resistance

Fixing state of connecting part

Naked eyes

No relaxation is allowed

6 months

Heating and assembly state of cap (partition)

Naked eyes

No relaxation is allowed

3 months

(1)

Please determine whether electric wire connected on regeneration resistance is relax.

(2)

Please determine whether over-heat condition occurs on regeneration resistance.

2005.12.27. Approval