27 0 137KB
Report No. IND 2050-1B/03
IEC/EN 60335-2-103:2002 Household and similar electrical appliances – Safety Part 2-103: Particular requirements for drives for gates,doors and windows Product
DRIVE FOR VERTICALLY MOVING SECTIONAL DOOR
Name and address of the applicant
FAAC S.p.A Via Benini, 1 I - 40069 Zola Predosa (BO) Italy
Name and address of the manufacturer
FAAC S.p.A Via Benini, 1 I - 40069 Zola Predosa (BO) Italy
Name and address of the factory
FAAC S.p.A Via Benini, 1 I - 40069 Zola Predosa (BO) Italy
Rating and principal characteristics
800W, 3.5A, 230Vac, 50Hz, 50Nm, IP54,
Trade mark (If any)
FAAC
Model/type
540 V
Serial no
06030019
Additional information
Temperature range: -20 ÷+55 °C See page 2
Tested according to
IEC 60335-2-103:2002 Safety of household and similar electrical appliancesParticular requirements for drives for gates,doors and windows
Report Reference No.
IND 2050-1A/03
Name and address of the testing laboratory
Ac
23RPM, 20µF, Cl. I, -20/+55°C
Nemko Spa Via Trento e Trieste, 116 20046 BIASSONO (MI)
Telephone (+39) 39 220120.1 Fax (+39) 39 2753240
Test sample(s) received 2003-07-16. Tested in period 2003-09-08 to 2003-09-15. The test results relate only to the sample(s) tested. Tested by Signature
Date
Roberto Tarro
2003-09-18
Name in block letters
Verified by Signature
Marcello Pozzoli
Date
2003-09-18
Name in block letters This form is only for use by NEMKO, or by others according to special agreement with NEMKO. The completed test report is not valid for external use, unless issued by NEMKO or attached to a NEMKO certification document. The report shall not be reproduced without written permission from NEMKO and may then only be copied in full. Issue NEMKO 03
-Page 2 of 12 -
Report No. IND 2050-1B/03 Tested according to:
IEC 60335-2-103:2002 EN 60335-2-103 Safety of household and similar electrical appliancesParticular requirements for drives for gates,doors and windows
Tested according to additional information:
Other requirements:
Drive for sliding gate composed by:
Singlephase Motor 230V∼ thermally protected
Control unit 200BT540
EN 60335-1:2001 Safety of household and similar electrical appliances EN12453:00 Industrial, commercial and garage doors and gates –Safety in use of power operated doors –Clause 5.2.1 Electrical drive units See Test report IND 2050-1A/03
General remarks: "(see remark #)" refers to a remark appended to the report. "(see appended table)" refers to a table appended to the report. Throughout this report a point is used as the decimal separator. The test results presented in this report relate only to the object tested. This report shall not be reproduced except in full without the written approval of the testing laboratory. Possible test case verdicts: P = Pass, F = Fail, N = Not applicable. Placed in the column to the right (Verdict) Summary of testing: According to manufacturer request tests 20.108 (MECHANICAL HAZARD) were not performed
Copy of marking plate See Test report 2050-1A/03
-Page 3 of 12 -
Report No. IND 2050-1B/03 Clause
Requirement – Test
5.
GENERAL CONDITIONS FOR THE TESTS
—
This clause of Part 1 is applicable as follows
__
5.2
Use of the drive and driven part specified for installation that give the most unfavorable conditions. The drive is adjusted in accordance with the instructions. The driven part may be simulated by artificial load
Result – Remark
The tests are performed without a door because the customer declares that the variation of motor current with the appliance loaded or unloaded is a little tenth of Ampere
Verdict
P
The drive is adjusted in accordance with the instructions. Duty cycle 40%
5.5
A wicket door is kept closing during the tests
N
5.7
If the drive is marked with an ambient temperature beyond the range of +5°C to+40°C the tests of Caluse 11, 13, 20.105 to 20.110 and 21 are carried out at the most unfavorable marked temperature.
6
CLASSIFICATION
6.1mod
Drives shall be class I, class II or class III
Class I
P
6.2
Drives or parts of drives, that are intended for exposure to outdoor conditions shall be at least IPX4.
Outdoor use, IP54
P
7.
MARKING
7.1mod
Drives shall be marked with the rated power input.
800W
P
Drives shall be marked with the ambient temperature range.
Operating ambient temperature –20 to +55°C
P
Test performed at 55°C
—
Drives supplied without driven part shall be marked with:
7.6
7.12
P
__
- The rated load in newtons or in newton-meters
50Nm
P
- The rated operating time, in minutes, unless the drive is intended for continuos operation.
Duty cycle (S3) 40%
P
Drives supplied with a driven part shall be marked with the rated number of operating cycles, unless the drive is intended for continuos operation.
N
Symbol 0533 of ISO 7000 – maximum temperature
N
Symbol 0534 of ISO 7000 – minimum temperature
N
The instructions shall state the substance of the following:
WARNING: Important safety instructions. It is important for the safety of persons to follow these instructions. Save these instructions.
P
Described in the instruction sheet
-Page 4 of 12 -
Report No. IND 2050-1B/03 The instructions shall include the substance of the following:
do not allow children to play with fixed controls. Keep remote controls away from children;
Described in the instruction sheet
P
explanation of mode indicators;
Described in the instruction sheet
P
details on how to use any manual release, and if applicable, state that activation of the manual release may cause uncontrolled movement of the driven part due to mechanical failures or an out-of-balance condition
Described in the instruction sheet
P
when operating a biased-off switch, make sure that other persons are kept away;
Described in the instruction sheet
P
when closing a window that has been opened by a fire-sensing system, make sure that other persons are kept away
7.12.1
N
details on how to re-adjust controls
Described in the instruction sheet
P
frequently examine the installation for imbalance and signs of wear or damage to cables, springs and mounting. Do not use if repair or adjustment is necessary
Described in the instruction sheet
P
Disconnect the supply when cleaning or other maintenance is being carried out, if the Appliance is automatically controlled
Described in the instruction sheet
P
The installation instructions shall state the substance of the following:
__
WARNING: Important safety instructions. Follow all instructions since incorrect installation can lead to severe injury.
Described in the instruction sheet
P
The installation instructions shall specify the type, size and mass of the driven part, and locations where the drive can be installed. They shall state that the installer is to check that the temperature range marked on the drive is suitable for the location.
Described in the instruction sheet
P
The installation instructions shall include the substance of the following: the necessary information for safe handling of a drive weighing more than 20 kg. This information shall describe how to use the handling means, such as hooks and ropes
Mass