36 0 177KB
D 0001-99 [2007/12/11 16:02:14]
1/4
Product HES Office
HES HES GENERAL TOLERANCES (CUTTING WORK)
D 0001-99 C REV4
1. SCOPE This standard specifies the tolerances for dimensions of metallic material products to be cut, when no symbol or numerical indication is given on drawings. 2. GRADES Dimensional and angular tolerances shall be classified into grades 1 and 2. 3. DIMENSIONAL AND ANGULAR TOLERANCES 3.1 Dimensional Tolerances for General Areas 3.1.1 Tolerances for holes and shafts(*1) Unit: mm Nominal Dimension Tolerance
Grade 1 Grade 2
1.0 to 10
Hole + 0.2 0 +0.4 0
Shaft 0 -0.2 0 -0.4
Over 10 to 100
Over 100 to 500
Hole + 0.3 0 + 0.6 0
Hole + 0.5 0 + 1.0 0
Shaft 0 -0.3 0 -0.6
Shaft 0 -0.5 0 -1.0
Over 500
Hole + 1.0 0 + 2.0 0
Shaft 0 -1.0 0 -2.0
Note (*1) The holes and shafts referred to in 3.1. are limited to those having areas which can be measured internally and externally.
■This engineering standard is a business secret owned and/or administrated by Honda Motor Co. Ltd., and any act to copy, use or transfer this engineering standard without prior approval constitutes illegal misconduct. .■本规格票是属于本田技研工业株式会社所有及/或管理的机密信息,非经事先许可、擅自复制、使用或转交本规格票的行为均属违 法行为。 ■本規格票は本田技研工業(株)が所有及び/又は管理する秘密情報であり、事前の承諾無く、本規格票を複写し、使用し、又は引き渡すことは違法行為になります。
D 0001-99 [2007/12/11 16:02:14]
2/4
3.1.2 Tolerances for areas other than holes and shafts Nominal Dimension Tolerance Grade 1 Grade 2
1.0 to 10 ±0.1 ±0.2
Over 10 to 100 ±0.15 ±0.3
Unit: mm Over 100 to 500 Over 500 ±0.25 ±0.5 ±0.5 ±1.0
3.2 Tolerances for Center Distance of Holes(*2) Unit: mm Nominal Dimension 100 and under Over 100 to 200 Over 200 to 500 Tolerance Grade 1 ±0.1 ±0.2 ±0.25 Grade 2 ±0.2 ±0.4 ±0.5 Note (*2) The hole mentioned here is a round hole. For all other types of holes, refer to 3.1.2. 3.3 Angular Tolerances Grade 1 ± 1°30' Grade 2 ± 3° 3.4
Tolerances for Internal and External Corner Radii (R), and 45 Chamfering (C) Unit: mm Nominal Dimension 0.2 to 1.0 Over 1.0 R C R C 0 + 0.2 0 + 0.4 Grade 1 - 0.2 0 -0.4 0 Tolerance 0 + 0.4 0 + 0.8 Grade 2 - 0.4 0 - 0.8 0
■This engineering standard is a business secret owned and/or administrated by Honda Motor Co. Ltd., and any act to copy, use or transfer this engineering standard without prior approval constitutes illegal misconduct. .■本规格票是属于本田技研工业株式会社所有及/或管理的机密信息,非经事先许可、擅自复制、使用或转交本规格票的行为均属违 法行为。 ■本規格票は本田技研工業(株)が所有及び/又は管理する秘密情報であり、事前の承諾無く、本規格票を複写し、使用し、又は引き渡すことは違法行為になります。
D 0001-99 [2007/12/11 16:02:14]
3/4
4. REMARKS The general tolerances shall not be applicable to dimensions where either one of the two surfaces relating to specified dimensions is a non-cut surface (such as cast, forged, sheet-metal worked, rolled, drawn, extruded, tumbled, or sand-blasted surfaces). Reference: Examples of Tolerances for General Areas The application example of tolerances for general areas are shown below indicating various types of dimensions.
where : Tolerance for general areas of holes : Tolerance for general areas of shafts : Tolerance for general areas other than holes and shafts
■This engineering standard is a business secret owned and/or administrated by Honda Motor Co. Ltd., and any act to copy, use or transfer this engineering standard without prior approval constitutes illegal misconduct. .■本规格票是属于本田技研工业株式会社所有及/或管理的机密信息,非经事先许可、擅自复制、使用或转交本规格票的行为均属违 法行为。 ■本規格票は本田技研工業(株)が所有及び/又は管理する秘密情報であり、事前の承諾無く、本規格票を複写し、使用し、又は引き渡すことは違法行為になります。
D 0001-99 [2007/12/11 16:02:14]
4/4
Revision Record Year Rec 61 EST
Issue 61/07/20
NewsNo 610201 -
Prep
Conf
Appvl
-
-
Remarks Former title [General tolerances (Cutting work)]
61
REV1 65/05/08
H65-5
-
-
-
61
REV2 65/10/16
H65-9
-
-
-
Change of title
61
REV3 65/10/21
H65-10 Shimane
Shimane
Hoshino
Change of explanation
61
Rewrit 76/08/21 e
-----
-
-
61
REV4 86/05/19
86008
Danjo
Tomino
Katagiri
61
Rewrit 95/03/14 e
Tanaka
Shimada
Yamada
Data transfer to PC
61
Correc 97/09/30 tion
97024
Kimura
Shimada
Morizumi
Correction of errors
99
Correc 99/08/04 tion
99011
Tomonaga
Naya
Tomino
Correction of errors
Rewritten by new drawing method
■This engineering standard is a business secret owned and/or administrated by Honda Motor Co. Ltd., and any act to copy, use or transfer this engineering standard without prior approval constitutes illegal misconduct. .■本规格票是属于本田技研工业株式会社所有及/或管理的机密信息,非经事先许可、擅自复制、使用或转交本规格票的行为均属违 法行为。 ■本規格票は本田技研工業(株)が所有及び/又は管理する秘密情報であり、事前の承諾無く、本規格票を複写し、使用し、又は引き渡すことは違法行為になります。