23 1 199KB
STANDARD UNSCHEDULED TASK CARD MODEL
A320FM
APPLICABILITY
CROSS REF NO.
ALL
RII
SKILL
ME
Y
CHAPTER PLAN MH
NO.
TC-US-32-41-12-400-001-A
REV.DATE
2016-11-11
32 0.5
ACCESS
ORDER NO. REF & VER
AMM & NOV 01, 2016
ZONE
711
SUBJECT WHEEL - NLG (2659GM, 2660GM) –INSTALLATION Comments: A、References Reference 32-41-12-400-001-A
Title Installation of the NLG Wheel (2659GM,2660GM)
B、Expendable Part FIG.ITEM
P/N
Nomencla
ure QTY
C、Tool Equipment Reference
Description
QTY
D、Consumable Material Reference
Prepared by
Description
Rajib Dhakal 2016-11-11
Specification
Reviewed by
Abhishek Shrestha 2016-11-11
Approved by
Accomplished On Reg. No. Mechanic/Date
HA-ME-F-109
Station
Actual MH Inspector/Date
PAGE 1 of 5
Zhao Jin 2016-11-11
STANDARD UNSCHEDULED TASK CARD
ITEM
1
2
NO.
TC-US-32-41-12-400-001-A
REV.DATE
2016-11-11
CONTENTS
MECHANIC INSPECTOR
WARNING: MAKE SURE THAT THE GROUND SAFETY-LOCKS ARE IN POSITION ON THE LANDING GEAR. WARNING: BE CAREFUL WHEN YOU USE CONSUMABLE MATERIALS. OBEY THE MATERIAL MANUFACTURER'S INSTRUCTIONS AND YOUR LOCAL REGULATIONS. A. Make sure that this(these) circuit breaker(s) is(are) open, safetied and tagged: ANEL
TION
DESIGN
IDENT.
LOCATION
121VU
HYDRAULIC/BRAKING AND STEERING/SYS2/SPLY
4GG
M36
121VU
HYDRAULIC/BRAKING AND STEERING/SYS2/CTL
3GG
M35
121VU
HYDRAULIC/BRAKING AND STEERING/SYS1/CTL
1GG
M34
121VU
HYDRAULIC/BRAKING AND
STEERI M33 NG/SYS 1/IND AND/SP LY 2GG
B. Aircraft Maintenance Configuration (1) Make sure that the wheel chocks are in position at the main landing gear. (2) Make sure that the NLG is in the correct configuration for the wheel change (Ref. AMM TASK 07-12-00-582-001). (3) Make sure that the warning notice is on the panel 400VU to tell persons not to operate the landing gear. (4) Make sure that the safety devices are installed on the landing gear (Ref. AMM TASK 32-00-00-481-001). (5) Make sure that the PROTECTOR NLG (J47548) is installed. NOTE: If the wheel has a pressure-sensor seal cap, make sure that the seal cap is correctly installed and safetied with a nut and a cotter pin. A. Tires of different type (1) Obey the tire mixability precautions (Ref. AMM TASK 32-41-00-910-001). B. Installation of the NLG Wheel CAUTION: MAKE SURE THAT THE GREASE USED FOR THE AXLE SLEEVE IS THE SAME AS THE GREASE USED FOR THE BEARINGS (CONE AND CAGE). IF YOU USE A DIFFERENT GREASE, YOU CAN CAUSE DAMAGE TO THE BEARINGS. (1) Preparation for installation (a) Make sure (if the tire mixability is not permitted) that the wheel for installation has the same type of tire (radial cross-ply) as the other wheel on the NLG. (b) Make sure that the retaining ring (11) is in its housing. (c) Clean the axle sleeve (1) and with Material No. 08BBB1 (Non Aqueous Cleaner-- Petroleum Based -) and dry it with filtered compressed air. (d) Make sure that the axle sleeve (1) is in the correct condition. (e) Apply a light coat of Material No. 03HBD9 or 03-GBB1 or 03-GCB1 on the axle sleeve (1) and the threads of the axle. NOTE: For lubricant grease specification and lubrication requirements, refer to (Ref. AMM D/O 12-22-00-00) .
HA-ME-F-109
PAGE 2 of 5
STANDARD UNSCHEDULED TASK CARD
ITEM
Cont 2
3
NO.
TC-US-32-41-12-400-001-A
REV.DATE
2016-11-11
CONTENTS
(2) Installation of the wheel (a) Clean the inner surface of the wheel bearings (surface that touches the axle). Do not apply grease on these surfaces. (b) Install the wheel with a HANDLING TOOL (1324A).Make sure that the valve is outboard. (c) Remove the PROTECTOR NLG (J47548). (d) Install the axle nut (10). (e) TORQUE the axle nut (10) to 21.80 m.daN (160.77 lbf.ft) with the ADAPTOR NLG (J47549) and, at the same time, turn the wheel in the same direction. Actual value_____________________ Torque wrench No.: (f) Loosen the axle nut (10). NOTE: You must make sure that the wheel does not turn when you loosen the axle nut. (g) TORQUE the axle nut (10) to 10.8 m.daN (79.65 lbf.ft) with the ADAPTOR NLG (J47549) and, at the same time, turn the wheel in the same direction. 用 ADAPTOR NLG (J47549) 拧 紧 螺 帽 (10) 到 力 矩 10.8 m.daN (79.65 lbf.ft),同时在轴螺帽轮转动的同样方向转动机轮。 Actual value 实际值__________________________ Torque wrench No./扭矩扳手编号: (h) Tighten the axle nut (10) until the holes for the bolts (5) are aligned. 拧紧轴螺帽(10)直到螺栓(5)的孔对正。 (i) Turn the wheel and make sure that the wheel is installed correctly. 旋转机轮并确保机轮正确安装。 (j) Install the casing (9). 安装壳体(9)。 (k) Install the bolts (5): 1 Install the bolts (5), the washers (2) and the new IPC-CSN (32-21-13- 12070) nuts (3) . CAUTION: MAKE SURE THAT YOU INSTALL THE BOLT AGAINST THE INNER SIDE OF THE AXLE NUT, AND THE WASHERS AND NUTS AGAINST THE OUTER SIDE OF THE AXLE NUT. IF YOU DO NOT, YOU CAN CAUSE DAMAGE TO THE NOSE WHEEL. (l) TORQUE the nuts (3) to between 0.4 and 0.45 m.daN (35.39 and 39.82lbf.in) and safety them with the new IPC-CSN (32-21-13-12-060) cotter pins (4). Actual value__________________________ Torque wrench No.: A. Close access (1) Put the hubcap (6) in position. (2) Apply a thin layer of Material No 06-LCG9 (SPECIAL MATERIALS (Material No. 06-LCG9)) to the screws (7). (3) Install the screws (7) and the washers (8). (4) TORQUE the screws (7) to between 0.4 and 0.51 m.daN (35.39 and 45.13 lbf.in) . Actual value: __________________________ Torque wrench No.: NOTE: The hubcap attachment holes have screw-lock inserts. It is
HA-ME-F-109
PAGE 3 of 5
MECHANIC INSPECTOR
RII
RII
STANDARD UNSCHEDULED TASK CARD
ITEM
NO.
TC-US-32-41-12-400-001-A
REV.DATE
2016-11-11
CONTENTS
MECHANIC INSPECTOR
not necessary to install lockwire on the screws (7). Cont 3
B. Aircraft Maintenance Configuration (1) Inflate the tire to the unloaded pressure (Ref. AMM TASK 12-14-32-614-001). Actual value__________________________ Measurement tool No.: (2) Lower the aircraft on its wheels (Ref. AMM TASK 07-12-00-582-001). (3) Make sure that the pressure of the tire is correct (Ref. AMM TASK 32-41-00-210-003). Measured value__________________________ Measurement tool No.: C. Remove the safety clip(s) and the tag(s) and close this(these) circuit breaker(s): PANEL
4
DESIGNATION
IDENT.
LOCATION
121VU
HYDRAULIC/BRAKING AND STEERING/SYS2/SPLY
4GG
M36
121VU
HYDRAULIC/BRAKING AND STEERING/SYS2/CTL
3GG
M35
121VU
HYDRAULIC/BRAKING AND STEERING/SYS1/CTL
1GG
M34
121VU
HYDRAULIC/BRAKING AND STEERING/SYS1/IND AND/SPLY
2GG
M33
A. Removal of the Equipment (1) Remove the safety devices from the landing gears (Ref. AMM TASK 3200-00-081-001) . (2) Make sure that the work area is clean and clear of tool(s) and other items. (3) Remove the warning notice(s). (4) Nose wheel removal/installation record. Left nose wheel □ Right nose wheel □ Offlog P/N: S/N: Onlog P/N: S/N:
HA-ME-F-109
PAGE 4 of 5
RII
STANDARD UNSCHEDULED TASK CARD
Appendix Figure
HA-ME-F-109
PAGE 5 of 5
NO.
TC-US-32-41-12-400-001-A
REV.DATE
2016-11-11