Package Cabinet: RBS 6110, RBS 6120 [PDF]

Zitiervorschau

Package Cabinet RBS 6110, RBS 6120

Operating Instructions

155/1543-LZA 701 6001/1 Uen H

Copyright

© Ericsson AB 2016, 2017. All rights reserved. No part of this document may be reproduced in any form without the written permission of the copyright owner. Disclaimer The contents of this document are subject to revision without notice due to continued progress in methodology, design and manufacturing. Ericsson shall have no liability for any error or damage of any kind resulting from the use of this document. Trademark List All trademarks mentioned herein are the property of their respective owners. These are shown in the document Trademark Information.

155/1543-LZA 701 6001/1 Uen H | 2017-11-08

Contents

Contents 1

Introduction

1

1.1

Tools

1

1.2

Packaging Material to Reuse

1

2

Package Cabinet

4

2.1

Package Cabinet

4

3

Transporting the Packaged Cabinet

155/1543-LZA 701 6001/1 Uen H | 2017-11-08

15

Package Cabinet

155/1543-LZA 701 6001/1 Uen H | 2017-11-08

Introduction

1

Introduction This document describes how to protect the cabinet and the climate roof module during transportation from warehouse to site.

1.1

Tools Before starting the procedure, make sure that the tools listed in Table 1 are available. Table 1

1.2

Required Tools

Tool

Product Name

Packing tape

–

Knife or cutter

–

Packing straps that can handle the load of the cabinet

–

Strapping equipment

–

Packaging Material to Reuse Make sure that the packaging material from the original packaging in Table 2 is available. Table 2 Part

155/1543-LZA 701 6001/1 Uen H | 2017-11-08

Amount

Name

1

Pallet with fitment bottom

2

Fitment profile. Illustration shows two variants, which are dependant on climate system.

1

Package Cabinet

Part

2

Amount

Name

2

Fitment profile middle front. Illustration shows two variants, which are dependant on climate system.

2

Fitment profile middle back

4

Corner packing profiles

1

Top fitment front. Illustration shows two variants, which are dependant on climate system.

155/1543-LZA 701 6001/1 Uen H | 2017-11-08

Introduction

Part

155/1543-LZA 701 6001/1 Uen H | 2017-11-08

Amount

Name

1

Top fitment back

2

Top fitment right and left

1

Edge board frame

3

Package Cabinet

2

Package Cabinet This section describes how to protect the cabinet with the climate roof module mounted by reusing packaging components from the original cabinet and climate roof module packaging.

2.1

Package Cabinet Caution! Tip risk. Unsecured equipment can tip over if not secured properly, which can cause serious injury. Secure products with a high center of gravity as soon as possible to avoid accidents.

To package the cabinet, do the following: Steps 1. Make sure the cabinet is standing on the pallet and the fitment bottom.

4

155/1543-LZA 701 6001/1 Uen H | 2017-11-08

Package Cabinet

Ge8776B

2. Place the two fitment profiles to the cabinet.

155/1543-LZA 701 6001/1 Uen H | 2017-11-08

5

Package Cabinet

A

B

Ge8776A

Key to illustration: A

Fitment profile for cabinet with heat exchanger climate roof module.

B

Fitment profile for cabinet with DAC climate roof module.

3. Fasten the two fitment profiles middle front and the two fitment profiles middle back, together with the four corner packing profiles.

6

155/1543-LZA 701 6001/1 Uen H | 2017-11-08

Package Cabinet

Ge8777A

4. Cut out the marked piece from the fitment top front according to the illustration.

155/1543-LZA 701 6001/1 Uen H | 2017-11-08

7

Package Cabinet

Ge8775A

5. Cut out the marked pieces from the fitment top back according to the illustration.

Ge8773A

6. Fasten the fitment top front and fitment top back to the cabinet.

8

155/1543-LZA 701 6001/1 Uen H | 2017-11-08

Package Cabinet

Ge8778A

7. Fasten the two corrugated sheets to the front fitments according to the illustration.

155/1543-LZA 701 6001/1 Uen H | 2017-11-08

9

Package Cabinet

Ge8778B

8. Apply packing tape to fixate the corner profiles.

10

155/1543-LZA 701 6001/1 Uen H | 2017-11-08

Package Cabinet

Ge8779A

9. Fasten the top fitment right and the top fitment left to the climate roof module.

155/1543-LZA 701 6001/1 Uen H | 2017-11-08

11

Package Cabinet

Ge8780A

10. Fasten the edge board frame on top of the climate roof module.

12

155/1543-LZA 701 6001/1 Uen H | 2017-11-08

Package Cabinet

Ge8781A

11. Fasten four packing straps according to the illustration.

155/1543-LZA 701 6001/1 Uen H | 2017-11-08

13

Package Cabinet

Ge8782A

14

155/1543-LZA 701 6001/1 Uen H | 2017-11-08

Transporting the Packaged Cabinet

3

Transporting the Packaged Cabinet If using a fork lift, no specific length on forks is needed to lift the cabinet. Secure the cabinet before starting transportation and make sure it is in the upright position according to Figure 1.

Ge8851B

Figure 1

Fixation and Transportation of Cabinet

155/1543-LZA 701 6001/1 Uen H | 2017-11-08

15