IC Card Instruction Manual A00 [PDF]

Zitiervorschau

2 1. System Overview

IC Card Management System User Guide

3

Figure 1 System architecture of IC card management system

Mark

The car call controller (MCTC-IC-A) is installed at the operating panel.

◆◆ Introduction The car call controller (MCTC-IC-A) communicates with the car top board (MCTCCTB) through RS485 bus to control floor selection authority of IC cards. The car call controller provides functions:

Single door

5

Install as follows:

Completed installation:

CN1

MOD1+/MOD1- RS485 terminal

◆◆Direct travel ride

Car call controller (MCTC-IC-A)

Key chain type (MCTC-IC-C2)

66.5mm

mm

.5 90

Figure 2 Product front view

Doublecolor LED indicator connection cable

4*(M4 nuts)

USB connection

IC Card writer (MCTC-IC-W)

Card writing

PC

Double color LED indicator connection terminal

Used to connect to the double color LED indicator

J11

Card reader terminal

Used to connect to the card reader by coaxial cable for opposite door elevator

D7

RUN indicator

Used to indicate the status when swiping system activation/deactivation card

D10

Communication indicator

Used to indicate the communication status with car top board (MCTC-CTB).

Table 4 DIP switch function description

USB key (MCTC-IC-L)

DIP Switch No.

Function Description

Example Set elevator 1# as follows:

MCTC-IC-A

MCTC-IC-A

This is a new-generation IC card management system independently developed and manufactured by Suzhou Inovance Technology Co., Ltd., by optimizing the previous generation based on a large number of applications and combining new industrial features.

MCTC-IC-A2

MCTC-IC-G

Product Features

Features Integration

Safety

Previous System

New System

The controller and card The controller and card reader are reader are separate. integrated. The IC card cannot be The IC card is encrypted individually encrypted and might be and cannot be copied. copied. ◆◆ Double color indicator

User Friendless It is less user friendly.

27.4 mm

101.0 mm

MCTC-IC-W

It connects to the PC to configure IC cards.

USB key

MCTC-IC-L

It connects to the PC to unlock the software.

MCTC-IC-C

Card type

IC card

MCTC-IC-C2

Set the button at ON side for opposite door elevators and set the button at number side for single door elevators.

9

4. Wiring

J6: Double color LED indicator connection terminal

MCTC-IC-A

J11: Card reader interface to connect to the CTB D1: Double color LED Indicator

◆◆ Technical Specification

Key chain type

Basic specifications

Environment

1 2 3 4 5 6 7 8 9 10

Input voltage

24 VDC±10%

Input current

< 300 mA

Response time

< 100 ms

Maximum quantity of stored card swiping records

9322

Maximum quantity of IC cards

1024

Maximum quantity of elevators

127 sets

ON

Length of coaxial cable

5m

Operating temperature

–10°C to +60°C

Humidity

30%–95% RH non-condensing

Storage temperature

–20°C to +70°C

•

• •

•

Insert the power supply plug into the car call controller after wiring is completed. Both the Run indicator D7 and the communication indicator D10 flashes. If the communication indicator D10 is steady on, check the wiring of CN1. 2. System activation/deactivation IC card test The system enters the IC card management system state with The buzzer tweets two times after swiping the system activation/deactivation IC card. The elevator is allowed for use if you swipe the card again with the buzzer tweets one time.

The administrator IC card is for the administrators to use any elevator. Select the floor manually after swiping the card. 4. Swiping times-based IC card test Set the swiping times between 10 and 20. The card can be swiped only when the swiping times are greater than zero. The swiping times decrease by one after each swiping. The buzzer tweets one time If the remaining swiping times are greater than 10, tweets two times if the remaining swiping times are less than 10 and tweets for three seconds if there is no remaining swiping times. 5.Time-based IC card test Adjust the clock of the car call controller or check the time setting of the card when only timebased IC cards are abnormal. If the time-based IC cards are still not working, replace the car call controller and set the elevator number and clock again.

◆◆ Elevator No.: The IC card holder can only use the corresponding elevator. ◆◆ The elevator number set by DIP switch prevails the elevator number set by system setting IC card. ◆◆ The elevator number can be set whether the power of car call controller is on or off. The DIP switch No.8 and No.10 are reserved and turned off by default.

Communication indicator D10 flashes quickly if communication with the car top board is normal. Communication indicator D10 is steady on if communication with the car top board is abnormal 7.RUN indicator D7 After swiping the system activation/deactivation IC card, the IC card management system is deactivated if the RUN indicator D7 is steady on and the buzzer tweets one time. After swiping the system activation/deactivation IC card, the IC card management system is activated if the RUN indicator D7 flashes and the buzzer tweets two times. 8. Double color LED indicator

• •

If there is no card swiping, both the front door and back door indicators are steady on in red color. After swiping the card, the corresponding indicator flashes in green color and the other indicator remains the same. The indicator flashes in red and green colors alternatively at a 2s interval when the records are being erased.

Warranty Agreement 1. The warranty period of the product is 18 months (refer to the barcode on the equipment). During the warranty period, if the product fails or is damaged under the condition of normal use by following the instructions, Inovance will be responsible

◆◆ Application and Wiring

for free maintenance.

Figure 5 MCTC-IC-A/MCTC-IC-A2 wiring diagram

2. Within the warranty period, maintenance will be charged for the damages caused by the following reasons: J6

CN2: Reserved

Car top board (MCTC-CTB)

CN1: Communication terminal for car top board (MCTC-CTB) 24V

MOD+ MOD-

MCTC-IC-G (Back door card reader)

a. Improper use or repair/modification without prior permission b. Fire, flood, abnormal voltage, other disasters and secondary disaster c. Hardware damage caused by dropping or transportation after procurement d. Improper operation

COM

e. Trouble out of the equipment (for example, external device)

DIP switch CN1 24V MOD1+ MOD1COM

D7: RUN indicator

24V

MOD+ MOD-

COM

3. The maintenance fee is charged according to the latest Maintenance Price List of

J11

Car call controller

D10: Communication indicator

•

Elevator 127# (opposite door):

J1

MCTC-IC-A

• •

•

Table 2 Car call controller (MCTC-IC-A) technical specifications Specification

1. Power-on test Use a multi-meter to measure the power supply and the voltage is 24 VDC±10%.

3.Administrator IC card test

•

•

Description of elevator number: D1: Double color LED Indicator

Item

6 7 8 9 10

1 2 3 4 5 6 7 8 9 10

Figure 4 MCTC-IC-A diagram

Ø5.5 mm

Access to Latest Manual

◆◆Visit the official website: www.inovance.cn.

◆◆ Pay attention to the installation to prevent equipment damage.

◆◆ Function Description of Terminal and DIP Switch

R3.25 mm

◆◆ Less wiring, plug and play

◆◆Contact with the sales agent, or

22.4 mm

90.0 mm

◆◆ Using system setting IC card to set elevator number

This manual is subject to change without notice. If you need the latest manual:

24.4 mm

104.0 mm

• •

6.Commnicaton indicator D10

ON

◆◆ Plug in or remove the connected components when power is off.

It is for the back door of opposite door elevators.

IC card writer

ON It is used to set the elevator number. 8421 code (binary-coded decimal) method is used. The 1 2 3 4 5 corresponding codes of number 1 to 7 are 1, 2, 4, 8, 16, 32 and 64. Elevator 6#:

◆◆ Ensure the operating environment satisfies related requirements, with enough heat dissipation clearance.

The administrator can set a password to activate or deactivate the IC card management system. Back door card reader

1~7

◆◆ Properly insulate the components against the ground.

The keypad supports the operations: Users can set and change the password. If the password is forgotten, users reset the password by using a replacement IC card.

Before using this product, read this manual carefully to fully understand features of the product and ensure safe use. This user guide describes product features, mounting dimensions, terminals, installation, commissioning and application examples. These information is for your reference.

Comparison between the new system and the previous system

◆◆ Before power-on, check and confirm the power supply is 24 VDC±10%.

It integrates car call controller (MCTCIC-A), back door card reader (MCTCIC-G1) and structural parts.

66.0 mm

Preface Car call controller with keypad

Figure 3 Physical dimensions

It is a replacement of the car call controller (MCTC-IC-A). Besides the card reading function, it has an additional keypad for password management. Users can choose to read the card directly or enter the password for elevator call.

1

Thank you for choosing MONARCH IC card management system for elevators.

Description

77.0 mm

Car call controller

Model

80.0 mm

A00 Data No.: 19010508

Component

MCTC-IC-A2

Commission the system when installation is completed in order to satisfy the requirements. Commission the system as follows:

•

◆◆ System Components Table 1 Description of system components

5. Commissioning

•

J6

R3.25mm

Back door card reader (MCTC-IC-G)

4*(M4-12 studs) USB connection

Used to connect to the car top board (MCTC-CTB) for Modbus communication

MOD2+/MOD2- RS485 terminal

◆◆Blacklist and records.

Radio frequency cable

Function Description

External 24 VDC±10% power Reserved supply

24+/COM

◆◆Time-based service

Communication cable

Card type (MCTC-IC-C)

CN2

◆◆Floor-based service ◆◆Swiping times-based service

Car top board (MCTC-CTB-C2)

Terminal Name

External 24 Used to provide 24 VDC±10% power VDC±10% power supply to the controller supply

24+/COM

Installation Method and Procedures

◆◆Specified-floor selection Opposite door

6

Table 3 Car call controller (MCTC-IC-A) terminal function description

3. Installation

2. Product Inforamtion

The system consists of car call controller, card reader, card writer and IC card.

4

J6

CN2 (MCTC-IC-A) 24V MOD2+ MOD2COM

Hall call board (MCTC-HCB)

◆◆ The car call controller uses the 24 VDC±10% power supply of car top board or hall call board. ◆◆ The car call controller communicates with the car top board through RS485 bus. Connect the car call controller to the RS485 terminal of the car top board or hall call board accordingly.

Inovance. 4. If there is any problem during the service, contact Inovance’s agent or Inovance directly. 5. This agreement shall be interpreted by Suzhou Inovance Technology Co., Ltd.

Suzhou lnovance Technology Co., Ltd. Address: No.16, Youxiang Road, Yuexi Town, Wuzhong District, Suzhou 215104, P.R.China http: //www.inovance.cn