34 0 3MB
#ANTHONY_GARDINER_TAGLIFTING_201212#
LI
FT
IN
G_
20
12
12
º
AN
TH
ON
Y_
GA
RD
IN
ER
_T
AG
Unidrive SP – Lift Speed Control System Document code: 0466017 Version: 4 Last revision: 21/07/2009
#ANTHONY_GARDINER_TAGLIFTING_201212# INDEX
INDEX INDEX ................................................................................................................................................ 2 1.
INTRODUCTION ....................................................................................................................... 3 DRIVE OPERATION ............................................................................................................... 3
1.2.
MODELS AND SIZES ............................................................................................................. 3
1.3.
OVERVIEW .......................................................................................................................... 4
1.4.
ADDITIONAL CARDS ............................................................................................................. 6
12
1.5.
INTERNAL PROGRAMMING ..................................................................................................... 6 CONNECTIONS ........................................................................................................................ 8
20
2.
12
1.1.
2.1.
POWER CONNECTIONS.......................................................................................................... 8
2.2.
ENCODER CONNECTION ........................................................................................................ 8 CONTROL CONNECTIONS ...................................................................................................... 8
G_
2.3. 3.
USER INTERFACE ................................................................................................................... 10 KEYPAD PLUS ..................................................................................................................... 10
3.2.
CONNECTION TO ORONA CONTROLLER ................................................................................. 12 SMARTCARD ...................................................................................................................... 13
FT
3.3. 4.
IN
3.1.
ADVANCE PARAMETER ADJUSTMENT ........................................................................................ 14 INTERNAL OPERATION ........................................................................................................ 14
4.2.
MOTOR CONFIGURATION .................................................................................................... 14
4.3.
ENCODER CONFIGURATION ................................................................................................. 20
4.4.
OPERATING SEQUENCE ....................................................................................................... 20
4.5.
SPEED PROFILES ................................................................................................................ 23
4.6.
INERTIA COMPENSATION .................................................................................................... 26
4.7.
SPEED CONTROL ................................................................................................................ 26
4.8.
CURRENT CONTROL (TORQUE)............................................................................................. 26
4.9.
START COMPENSATION ....................................................................................................... 27
4.10.
BRAKING RESISTANCE ........................................................................................................ 29
4.11.
RESCUE OPERATION ........................................................................................................... 29
AG
_T
ER
RFC MODE ......................................................................................................................... 29
IN
4.12. 5.
LI
4.1.
FUNCTIONS ........................................................................................................................... 30 INVERSION OF DIRECTION OF ROTATION ............................................................................. 30
5.2.
MOTOR AUTO TUNING ........................................................................................................ 31 SM-APPS.LITE SPECIAL FUNCTIONS ..................................................................................... 32
GA
5.3. 6.
RD
5.1.
PROBLEM SOLVING ................................................................................................................ 37 PROGRAMMING PROBLEMS .................................................................................................. 37
6.2.
DISPLAYING STATUS VARIABLES ......................................................................................... 40
6.3.
PERMANENT MAGNET SYNCHRONOUS MOTORS ..................................................................... 41 FREQUENT PROBLEMS......................................................................................................... 42
ON
6.4.
Y_
6.1.
6.5.
DRIVE FAULTS ................................................................................................................... 51
6.6.
CABLING ADVICE ............................................................................................................... 56
INDEX OF ELECTRICAL DIAGRAMS ........................................................................................... 60
8.
REPLACEMENT PARTS ............................................................................................................. 61
AN
TH
7.
8.1.
EQUIPMENT REPLACEMENT .................................................................................................. 61
8.2.
ADDING AN SM-APPS.LITE CARD .......................................................................................... 61
8.3. 9.
REPLACEMENT CODES......................................................................................................... 62 DEFAULT PARAMETERS ........................................................................................................... 66
9.1.
INSTALLATION TYPES ......................................................................................................... 66
9.2.
PARAMETER LISTS FOR EACH INSTALLATION ........................................................................ 67
0466017 - Unidrive SP – Lift Speed Control System
2/83
#ANTHONY_GARDINER_TAGLIFTING_201212# INTRODUCTION
1. INTRODUCTION
As regards Orona, this drive can be used to control the following types of vertical lift motor:
12
The Unidrive SP controller is a frequency drive made by “Control Techniques” that provides control for asynchronous and synchronous motors.
Geared Asynchronous motors (O-140, O-170, SASSI) with closed loop control (with encoder).
•
Gearless synchronous motors: M33, M33 optimised, M34, Nuevo Renova Electrico, Zetatop (Ziehl-Abegg) and Z6 or Z10 (Leroy Somer).
20
12
•
G_
1.1. DRIVE OPERATION
FT
IN
The drive is based on an Insulated Gate Bipolar transistor (IGBT) based frequency converter that works in Pulse Width Modulation (P.W.M.) with an elevated switching frequency (3-16kHz, 8kHz by default), ensuring silent operation. This system allows motor supply voltage and frequency to be controlled, providing precise control over speed and torque for any motor operating state.
LI
At the supply input, the Unidrive SP has a diode bridge to convert three-phase alternating current into direct current, which is what is required to supply the transistors. This “DC bus” contains capacitors to prevent the voltage oscillating.
_T
AG
DANGER: Accumulated Load in Capacitors The voltage accumulated by the capacitors is potentially mortal. After disconnecting the power supply, wait 10 minutes before connecting/disconnecting power cables (power supply, motor, DC bus or braking resistor).
ER
When the lift moves in the load direction, the energy returned by the motor has to be dissipated by a brake resistance so as not to damage the DC bus capacitors. Where this resistance fails or is not connected, the drive is automatically disconnected before the capacitors can be destroyed.
IN
To guarantee electromagnetic compatibility (EMC), the drive requires an anti-interference filter at the power supply input and the use of shielded and ferrite cables at the motor output (as described in section 6.6).
GA
RD
The control unit is based on a digital microprocessor system, that uses information about motor speed (read from the encoder) and power consumption (internal drive reading) to control motor speed and torque at all times engine to achieve an optimum speed profile under any load condition.
Y_
1.2. MODELS AND SIZES
ON
Drive size and specific model can be identified from the label on the front panel (see point 1.3):
AN
TH
Model and size
Control Techniques serial number
Within the drive model, the first number indicates its physical size (at Orona sizes 1 to 4 are used). Within each size, there are various alternatives depending on motor voltage that can be controlled:
0466017 - Unidrive SP – Lift Speed Control System
3/83
#ANTHONY_GARDINER_TAGLIFTING_201212#
Rated Current (Orona application table)
1405
3kW
7.6 A
7.5 A
1406
4 kW
9.5 A
9.5 A
2401
5.5 kW
13 A
12 A
2402
7.5 kW
16.5 A
2403
11 kW
25 A
2404
13.5 kW
29 A
3401
15 kW
32 A
30.3 A
3402
18.5 kW
40 A
37.8 A
3403
22 kW
46 A
43.5 A
4401
30 kW
4402 4403
12
15.6 A
23.6 A
G_
IN
FT LI
Size
26.6 A
60 A
56.8 A
37 kW
74 A
68 A
45 kW
96 A
85 A
_T
AG
Model
12
Drive Power
Rated Current (acc. manufacturer )
20
INTRODUCTION
ER
Brake resistance models depend on lift type and power, consult section 8.3.
IN
1.3. OVERVIEW
Y_
slot
GA
SmartCard
RD
All sizes:
AN
TH
ON
Serial connection
Encoder connector
Off: controller powered off Status LED Label Slot 1 Slot 2 Slot 3
On: controller operational Blinking: controller faulty
Additional card slots
Control signal connectors Alarm signal connector
0466017 - Unidrive SP – Lift Speed Control System
4/83
#ANTHONY_GARDINER_TAGLIFTING_201212# INTRODUCTION Sizes 1, 2 and 3:
*
12
*
LI
FT
IN
G_
20
*
12
Brake resistance (DC2/+DC – BR)
_T
AG
Supply (L1,L2,L3) y motor output (U,V,W)
Removed at factory because not compatible with external filter
Supply (L1,L2,L3)
AN
TH
ON
Y_
GA
RD
*
IN
ER
Size 4:
(*) Internal filter:
Motor output (U,V,W)
Brake resistance (+DC – BR)
0466017 - Unidrive SP – Lift Speed Control System
5/83
#ANTHONY_GARDINER_TAGLIFTING_201212# INTRODUCTION
1.4. ADDITIONAL CARDS
12
The Unidrive SP can carry diverse optional cards to provide additional features. These cards are placed in the slots under the front cover, and up to 3 cards can be inserted per drive.
20
When the drive starts up and detects that a card has been removed or added, it gives an (SL.rtd) fault that can be reset from the Keypad Plus or from the Drive menu on the Maintenance Terminal (TMR).
12
There are a great variety of cards that allow, for example, inputs and outputs to be added to the drive, special encoders to be controlled, etc. Each of these cards can be identified by its colour.
IN
G_
ATTENTION To install or remove a card, disconnect the power from the drive and wait at least one minute.
FT
1.4.1. SM-Apps.Lite card
LI
The card most used by Orona is the ‘SM-Apps.Lite’, which can be identified by its white colour. This card contains a microprocessor and memory independent from those inside the drive.
_T
AG
The program it contains (factory installed) allows additional features to be added as described in later sections. Must be inserted in lowest slot (slot 3).
IN
1.4.2. SM-I/O Plus card
ER
This card is being installed in all drives from April 2009, although it can also be installed in older drives.
Y_
GA
RD
This card allows additional inputs and outputs to be added to the drive. It is only used in ARCA I lifts where an original M33 machine has been replaced with an optimised M33 machine. Provides the drive with a brake contact reader (as the ARCA I controller doesn’t have one). Does not contain a program, menu 17 which corresponds to slot 3 is simply programmed, which is where the card should be inserted. Installation of this card is described in instruction IIM-036-0 (M33 Machine kit and throw frame).
ON
1.5. INTERNAL PROGRAMMING 1.5.1. Basic parameters
AN
TH
All Unidrive SP drives are configured using a series of parameters distributed on menus. These parameters have a type 12.40 denomination, which means parameter 40 of menu 12. These parameters can be bits (on/off), whole numbers or numbers with decimals. Some of these are “read only” and serve to display the state of certain internal signals. In these instructions, references to drive parameters will be preceded with ‘Pr’ (for example, Pr 0.14). Section 3 describes how to access these parameters. Parameter values can be recorded and recovered to/from the SmartCard or a PC (via CTSoft software). Programming of these parameters is different depending on the type of installation, the load and the speed.
0466017 - Unidrive SP – Lift Speed Control System
6/83
#ANTHONY_GARDINER_TAGLIFTING_201212# INTRODUCTION 1.5.2. PLC Software:
12
In addition to these parameters, the drive contains a small internal automaton called a PLC to better adapt the product to the application (in Orona's case, the lift). This PLC software is recorded on all Unidrive SP drives except the "original" M33.
12
The PLC can be recorded and recovered to/from the SmartCard or a PC using SYPTLite software. There are 2 different software programmes, one for asynchronous motors and the other for synchronous motors.
20
1.5.3. DPL Software
G_
The SM-Apps.Lite card, like the PLC, enables native code to be developed, called DPL, to adapt the drive to the lift, but its memory and processing capacity is very much superior.
IN
The DPL software recorded on the card performs the same functions as the PLC and provides additional features (described further on). Drives with the factory installed SM-Apps.Lite card, will have a programmed but deactivated PLC and the operating sequence will be handled by the software on the SM-Apps.Lite card.
LI
FT
The software on the card does not change with the appliance type, although in time new versions of the software will appear (this can be queried via parameter Pr 20.17). In the event of a card fault, it can be stopped and the PLC activated whist it is replaced, as described in section 6.1.5.
AG
The DPL software on the SM-Apps.Lite card cannot be recorded or recovered from the SmartCard. A PC and Winflasher software are necessary for recording. PLC Software
YES YES YES YES YES YES YES
Asynchronous Asynchronous NO Synchronous Synchronous Synchronous Synchronous
DPL Software
Only if SM-Apps.Lite card inserted
RD
IN
ER
M322 Machine room M33 original M33 extended M33 optimized MRL Ziehl-Abegg / Leroy-Somer M34
Basic parameters
_T
Lift type
Y_
GA
ATTENTION: IF THE DRIVE HAS AN Apps.Lite CARD The PLC and DPL programs are recorded on the drive, but they can no operate simultaneously. The SM-Apps.Lite card (DPL) program deactivates the PLC automatically on start up.
ON
Parameters exist for displaying the status of the PLC and DPL software, which can be accessed via the Orona MT or the Keypad Plus:
AN
TH
Software and status PLC Software Not recorded Stopped Running DPL Software Not recorded Manually stopped Running Stopped due to an error SM-Apps.Lite card not installed
Keypad Plus
Orona MT
Pr 11.48 0 1 2 Pr 17.03 nonE (0) StoP (1) Run (2) triP (3) Menu 17 doesn’t exist
5.7.3 Status No Stop Run 5.7.3 Status No Stop Run Av No
0466017 - Unidrive SP – Lift Speed Control System
7/83
#ANTHONY_GARDINER_TAGLIFTING_201212# CONNECTIONS
2. CONNECTIONS
12
Frequency drive IGBT switching causes electromagnetic interference. To minimize its effect it is essential that the electrical connections are made as indicated in this section and in section 6.6.
12
The location of all terminals described is displayed in section 1.3.
20
2.1. POWER CONNECTIONS
IN
G_
DANGER: Accumulated Load in Capacitors The voltage accumulated by the capacitors is potentially mortal. After disconnecting the power supply, wait at least 10 minutes before connecting/disconnecting power cables (power supply, motor, DC bus or braking resistor).
FT
The drive must be supplied from a 380-415V three-phase supply via terminals L1, L2, L3. To ensure compliance with lift regulations an electromagnetic compatibility filter, a circuit breaker and a residual current device must be employed.
LI
The braking resistor must be connected between terminal BR and terminal DC2 or DC+ (the name changes depending on drive size) and the cable-set that joins the drive with the resistor must be shielded, and the mesh must be fastened to the plating via metallic straps at each end.
ER
2.2. ENCODER CONNECTION
_T
AG
The power output (terminals U,V,W) goes to power contactor C1. This stretch of cable, to minimise electromagnetic emissions, is short and is would 2 or 3 times around some ferrite. The cable from the contactors to the motor is connected using shielded cabling for the same reason, and the mesh must be fastened to the case via metallic straps at each end.
IN
The Unidrive SP uses an encoder reading to control motor rotation speed. A good signal is fundamental for guaranteeing proper system operation.
RD
To ensure this shielded cable is used which is connected to the front of the drive via a “Sub D-15” connector.
GA
PRECAUTION The encoder cable should be protected by separating it as much as possible from the motor power cables and it is recommended that it be replaced if damaged or cut.
Y_
2.3. CONTROL CONNECTIONS
Secure Disable: this signal indicates to the drive that it should apply current to the motor output because the contactors have operated.
AN
TH
•
ON
The controller controls drive operation (and thereby that of the motor) via a set of control signals:
•
Rescue: indicates that the emergency EMC contactor has operated and that the drive should operate in rescue mode (see section 4.11).
•
Speed levels B1, B2, B3: these 3 digital signals set movement speed via a binary code (see section 4.5.1).
•
Ascend/Descend: these 2 digital signals set the movement direction. ATTENTION For the ‘up’ signal to work there must be a bridge between terminals 3 and 6.
0466017 - Unidrive SP – Lift Speed Control System
8/83
#ANTHONY_GARDINER_TAGLIFTING_201212# CONNECTIONS The cabling for these inputs is shown in the table:
22
22
31
8
B1 Speed level
29
B2 Speed level
28
B3 Speed level
27
Rescue
26
3 6
20
Descend
26
K3 K4
5 8
* K5 K6 K7 PBCM
11
IN
5
31
Unidrive SP
Ascend
EMC
FT
Secure Disable
C2
12
C1
G_
Common (24V internal)
Connection
12
Termin al
Signal
*
27 28 29 23
LI
(*) These 1kΩ resistances go to the internal drive 0V (terminals 11 and 23) and make inputs more robust as regards electromagnetic interference.
AG
In the case M33, M33 extended, M33 optimized, Leroy-Somer or Ziehl-Abegg lifts, a car load level reading is also used to open the car brake as soon as it moves and achieve optimum comfort: Terminal
Type
7
A 0-10V (PQ Orona) or 0-20mA (Micelect LM3D) signal can be used. See section 0
_T
Signal
ER
Weight level (+)
3
IN
Weight reference (-)
RD
In addition, the drive has the following outputs to the controller:
Signal
Terminal
Y_
GA
Drive alarm (relay contact)
AN
TH
ON
Brake opening (24V transistor) Advance door opening (24V transistor)
Use
41 - 42
Relay contact that opens if the drive is faulty, indicating to the controller that it should not attempt to move.
24 (+) y 11 (-)
Allows the drive to control brake opening to improve comfort (see section 4.4).
25 (+) y 11 (-)
Only ARCAI lifts. Activates if car speed is less than 0.3m/s (allowing doors to open).
To see the status of these inputs and outputs, see section 6.2.1.
0466017 - Unidrive SP – Lift Speed Control System
9/83
#ANTHONY_GARDINER_TAGLIFTING_201212# USER INTERFACE
3. USER INTERFACE
12
3.1. KEYPAD PLUS
LI
FT
IN
G_
20
12
The Keypad Plus is a Control Techniques tool that allows internal drive parameters to be displayed and modified, faults to be resolved, etc. It connects to the serial port on the drive front panel via a standard straight RJ45 cable:
AG
The Keypad contains several pushbuttons, the most important being: Mode: to change between different modes: status, parameter display and parameter editing
_T
Reset: enables the equipment to recover from faults and also serves to execute certain special functions (see further on). Help: a brief description of the parameter selected appears on screen when pressed.
ER
Arrows: for navigating parameters and menus, and changing parameter values. This is described in the section on Using the Keypad Plus.
The top line displays:
The parameter value or the current fault in the event that the drive is faulty, in the right corner.
The 2 bottom lines display a description of the parameter (or the help text if the Help key has been pressed).
Y_
•
The parameter selected or the drive status in the left corner.
GA
• •
RD
•
IN
The keypad display consists of 3 alphanumeric horizontal lines:
Status indication
ON
When first connected to a drive, wait at least one minute for it to update itself (will indicate Reading Data Base and Programming Flash).
AN
TH
The keypad is in Status Mode by default, that is, it displays drive status:
•
inh: the drive is not faulty but does not apply power (because the controller has not indicated that it should do so via the SecureDisable input).
• •
run: the drive is applying power to move the motor.
•
PLC: PLC software is running (see section 1.5.2). This indication blinks every 10 seconds or so.
StoP: the drive applies power to keep the motor stopped. Appears when Direction, Speed and SecureDisable set points are removed next to Dec (decelerating).
0466017 - Unidrive SP – Lift Speed Control System
10/83
#ANTHONY_GARDINER_TAGLIFTING_201212# USER INTERFACE
•
triP: the drive detects a fault and will not apply power to the motor until it has been resolved. The screen also displays a fault code (see section 6.5).
• •
Auto / TunE: blinks during auto tuning (see section 5.2).
12
12
no link: when the keypad Plus is remotely connected (with network cable) and an operation is being performed (record to/from Smartcard, etc...). Despite the appearance of this message, the operation is executed correctly.
20
•
rdY: when a SecureDisable signal is present, but no operating signals (direction or speed). The drive does not provide output. This should not arise in Orona applications, but if it were to appear, cabling should be checked and the error location established.
G_
Using the Keypad Plus:
inh
0
The top right hand side indicates the fault code (only where present, in which case it blinks).
LI
To access Parameter Mode, Press
or
0.10
Editing Mode
GA
RD
After a while in this mode without pressing a button, the keypad automatically returns to Status Mode.
Y_
The top left hand side indicates parameter selected.
ON
The top right hand side indicates the value for this parameter. The digit to be modified blinks.
AN
TH
This mode serves parameter values.
to
modify
After a while in this mode without pressing a button, the keypad automatically returns to Status Mode.
0.15
65
ER
Use the vertical arrows to change parameter
IN
This mode serves for navigating the different drive menus and viewing its parameter values.
again
0
_T
The top right hand side indicates the value for this parameter.
To return to Status Mode, press
AG
Parameter Mode The top left hand side indicates parameter selected (blinks).
FT
The top left hand side indicates drive status (doesn’t blink).
IN
Status Mode
0.15
45
To access Edit mode, press
*
0.15
To return to Parameter Mode, validating the new parameter value, press
45
0.15
Use the horizontal arrows to select the digit you wish to change
0.15
65
Use the vertical keys to change the digit value
45
(*) Some drive parameters are “Read Only”, and therefore access to Editing Mode may not be possible.
0466017 - Unidrive SP – Lift Speed Control System
11/83
#ANTHONY_GARDINER_TAGLIFTING_201212# USER INTERFACE Advanced Menu Access
12
By default, only menu 0 parameters (Pr 0.XX) can be accessed from the Keypad Plus. If Pr 0.49 is changed from L1 to L2, the rest of the menus can be accessed when pressing left and right keys (parameters for menu 1 are Pr 1.XX, menu 2 are Pr 2.XX…). Fault recovery descriptions for all the faults that can be cause them. To recover, press the reset button
.
20
Parameter recording
12
If the drive has a fault, the screen will display triP and a fault code. Section 6.5 provides
value 1000 for Pr x.00 (in any menu) and press the reset button
.
3.2. CONNECTION TO ORONA CONTROLLER
IN
G_
If a parameter has been modified, by pressing the M button it is only stored in volatile memory, and it will therefore be lost following a power down. To permanently record parameters, enter
LI
FT
The drive can be customized and monitored via the Orona Maintenance Terminal. To do so the Arca II controller communicates via 485 through the serial port on the front of the drive (such as on the Keypad Plus).
Directly from the main board. Only 5124423 main boards (June 2009) are prepared for this. Via a loadweights board (5124340), which acts as a “translator” from CAN bus to RS485. This communication is used on the Optimized M33, Leroy-Somer and Ziehl-Abegg.
_T
• •
AG
This communication is not possible with original and extended M33 lifts. For the rest this can be performed in two ways:
ER
Drive access from the MT
IN
On the Orona MT, the Unidrive SP drive is a controller node. From the Main Menu, enter Current and then Drive. If there are no Unidrive SPs connected (or there is a communications fault) nothing will appear, to the contrary the following menus will be available: 1. FAULTS: can be used to see if the drive is faulty or not, and to recover faults.
RD
2. HISTORIC: this menu allows the last 10 faults registered by the drive to be displayed.
GA
3. VARIABLES: this menu displays the status of some of the drive’s internal variables, speed readings and motor voltage and the status of inputs and outputs.
Y_
4. FUNCTIONS: this menu provides access to different drive assembly and maintenance utilities, described in section 5. This menu also includes SmartCard recording and reading functions (see section 3.3).
AN
TH
ON
5. PARAMETERS: any drive parameter can be changed via this menu (as described in section 4). It is important to highlight that the MT (unlike the Keypad Plus) cannot operate with decimals, and therefore many parameters appear in tenths (d), hundredths (c) or thousandths (m). For example, current is in decimals and therefore to program a current of 12A, the parameter should be adjusted to [120]d. In this standard, references to parameters on these menus takes the form ‘TMR 5.2 Vmax’. IF a parameter only refers to the Keypad Plus (for example, Pr 1.27) the parameter can only be accessed from TMR 5.8 Manual Parameter.
Parameter recording After modifying parameters (menu 5) or using functions (menu 4), enter TMR 4.3 Store Parameters = [YE] to not loose changes when the power is turned off.
0466017 - Unidrive SP – Lift Speed Control System
12/83
#ANTHONY_GARDINER_TAGLIFTING_201212# USER INTERFACE
3.3. SMARTCARD
12
20
The card should be inserted with the contacts facing the right side of the drive. There is no need to turn off the power when inserting or removing the card.
12
All drives come with a SmartCard. At the factory all drive parameters and PLC software for each installation are recorded on the card, which can therefore be used to restore original parameters in the event of undesired modifications, or drive substitution by a new unit.
G_
ATTENTION The DPL program on the SM-Apps.Lite card is not recorded on the SmartCard. This card can only be recorded to at the factory or on a PC.
Using the Keypad Plus: program parameter Pr x.00=0 + Using the Orona MT: TMR 1 Fault recov. = YES
FT
• •
IN
If a fault occurs during any dumping process, observe fault code and consult section 6.5. To recover the fault:
LI
Drive programming from the SmartCard When performing this operation drive parameters and PLC program are deleted and are recorded from the contents of the SmartCard: Using the Orona MT: a. Recover only parameters: TMR 4.4 Read SM = YES b. Recover parameters and PLC: TMR 4.4 SM -> Inverter = YES
•
Using the Keypad Plus:
_T
AG
•
ER
c. Recover PLC program: Pr x.00=6004 + Attention: the 'Original' M33s (i.e. not extended or optimized) did not have a PLC, and therefore this operation should not be performed (would cause an error). d. Recover parameters: Pr x.00=6001 +
IN
e. Record parameters: Pr x.00=1000 +
GA
RD
Record drive data to SmartCard When performing this operation factory recorded parameters are lost, but if any encoder or machine modifications have been made (or if an auto adjustment has been performed) it is recommended that the new data be recorded to the card. Using the Orona MT: f. Record parameters only: g. Record parameters and PLC:
•
Using the Keypad Plus:
TMR 4.4 Actualise SM = YES TMR 4.4 Inverter -> SM = YES
ON
Y_
•
AN
TH
h. Unprotect SmartCard: Pr x.00=9777 + i. Delete SmartCard: Pr x.00=9999 + j. Save PLC software: Pr x.00=5004 + Attention: the 'Original' M33s (i.e. not extended or optimized) did not have a PLC, and therefore this operation should not be performed (would cause an error).
k. Record parameters: Pr x.00=3001 + l. Protect SmartCard: Pr x.00=9888 +
0466017 - Unidrive SP – Lift Speed Control System
13/83
#ANTHONY_GARDINER_TAGLIFTING_201212# ADVANCE PARAMETER ADJUSTMENT
4. ADVANCE PARAMETER ADJUSTMENT
12
4.1. INTERNAL OPERATION Most drives require the use of PLC or DPL software (see section 1.5). Using the Keypad Plus:
Pr 17.03 = run
Using the Orona MT:
TMR 5.7.4 Status = run
20
• •
12
If the drive has the SM-Apps.Lite card, the DPL software must be running:
Using the Keypad Plus:
Pr 11.48=2
Using the Orona MT:
TMR 5.7.3 Status = run
IN
• •
G_
If the drive does not have the SM-Apps.Lite card and is not an “original M33" (see section 4.2), the PLC software must be running:
FT
If the correct software is not running, it can be started as described in section 6.1.
LI
4.2. MOTOR CONFIGURATION 4.2.1. CONTROL MODE
Gearless asynchronous motors: Pr 0.48=C.L.VECt (TMR 5.1 Mode = V.L.Closed)
_T
• •
AG
Parameter Pr 0.48 (or TMR 5.1 Mode) determines the type of motor controlled by the drive. The Control Techniques drive can control 2 types of motor:
Gearless synchronous motors: Pr 0.48=SERVO (TMR 5.1 Mode = SERVO)
IN
ER
However, changing the drive control mode (changing Pr 0.48) requires entering a code in Pr 0.00 and resetting all parameters to the default values used by Control Techniques. Given that these values are not valid for the Orona application, do not change the control mode in this manner.
RD
If you wish to change the drive control mode (because it does not correspond to the motor installed), you can: Use a SmartCard: the card should be programmed for the correct type of installation. Section 0 describes how the process should be performed.
•
Using the SM-Apps.Lite card: if the drive contains this type of card (or if one is installed), the “reset to default parameters” function can be used (see 5.3.3) to program all parameters with the correct values for the installation.
Y_
GA
•
ON
4.2.2. GEARED ASYNCHRONOUS MOTORS
AN
TH
The following motors are asynchronous motors that rotate at high speed (1000-1500rpm) and therefore require gearing to adapt to the lift pulley rotation speed. To control them, the drive should be configured in Closed Loop Vector mode:
• •
Using the Keypad Plus:
Pr 0.48=C.L.VECt
Using the Orona MT:
TMR 5.1 Mode = Closed L.V.
0466017 - Unidrive SP – Lift Speed Control System
14/83
#ANTHONY_GARDINER_TAGLIFTING_201212# ADVANCE PARAMETER ADJUSTMENT M233 MACHINES
WITH C.T. FROM JULY 2005
Inductance
10-13p 1500rpm
107d 10.7 1341m 1.341 11690m 11.69
132d 13.2 913m 0.913 8749m 8.749
91d 9.1 1198m 1.198 9826m 9.826
125d 12.5 826m 0.826 7611m 7.611 2 4
232d 23.2 371m 0.371 3868m 3.868
Poles
3 6
Nom. Voltage
12
8p 1500rpm
20
Resistance
4-6p 1500rpm
G_
Nom current
8p 1000rpm
380
rpm nominal
950
1445
1440
1440
Pow. factor
767m 0.767
749m 0.749
775m 0.775
856m 0.856
855m 0.855
Gain.P.curr
176
168
148
146
Gain.I.curr
865
748
773
676
FT
946
LI
112 460
AG
TMR 5.5.1 Pr 0.46 TMR 5.5.1 Pr 5.17 TMR 5.5.1 Pr 5.24 TMR 5.5.1 Pr 0.42 TMR 5.5.1 Pr 0.44 TMR 5.5.1 Pr 5.08 TMR 5.5.1 Pr 0.43 TMR 5.5.1 Pr 0.38 TMR 5.5.1 Pr 0.39
4-6p 1000rpm
IN
Lift type
O-170 or SASSI MACHINES
12
The M322s are geared asynchronous motors and drum brakes. The Control Techniques began to be used in the ARCA II controller (contactors and shaft drive).
WITH C.T. FROM JULY 2005
ER
_T
Geared asynchronous machines and drum brakes are used in lifts with machine rooms, which can be Orona (O-170) o SASSI (MF82 or MF94). Only used with Control Techniques with controller ARCA II.
Lift type
Nom current
Y_
TMR 5.5.1 Pr 0.46 TMR 5.5.1 Pr 5.17 TMR 5.5.1 Pr 5.24 TMR 5.5.1 Pr 0.42 TMR 5.5.1 Pr 0.44 TMR 5.5.1 Pr 5.08 TMR 5.5.1 Pr 0.43 TMR 5.5.1 Pr 0.38 TMR 5.5.1 Pr 0.39
GA
RD
IN
If the data is not displayed in the table, program: • Pr 0.42=4 and Pr 0.44=380 • Pr 0.46 and Pr 5.08 according to rating plate. • Perform a static auto tuning to obtain the rest (see section 5.2.2).
AN
TH
ON
Resistance Inductance
O-170 7.5cv
O-170 10cv
O-170 15cv
MF82 16cv
MF82 21cv
MF94 16cv
MF94 22cv
MF94 25cv
MF94 31cv
MF94 34cv
130d 13 926m 0.926 8704m 8.704
160d 16 652m 0.652 6411m 6.411
230d 23 444m 0.444 4522m 4.522
280d 28 409m 0.409 3232m 3.232
320d 32 335m 0.335 2742m 2.742
28d 28 415m 0.415 3189m 3.189
330d 33 335m 0.335 2746m 2.746
386d 38.6 303m 0.303 2504m 2.504
550d 55 135m 0.135 1410m 1.410
580d 58 143m 0.143 1416 1.416
Poles
2 4
Nom. Volt. rpm nominal
380 1441
1450
1449
1427
1435
1430
1430
1442
1482
1480
Pow. factor
820m 0.82
851m 0.851
860m 0.86
793d 0.793
835m 0.835
774m 0.774
847m 0.847
856m 0.856
756m 0.756
723m 0.723
Gain.P.curr
131
123
131
120
127
118
128
134
98
122
Gain.I.curr
598
534
551
649
665
659
666
692
402
525
0466017 - Unidrive SP – Lift Speed Control System
15/83
#ANTHONY_GARDINER_TAGLIFTING_201212# ADVANCE PARAMETER ADJUSTMENT 4.2.3. PERMANENT MAGNET SYNCHRONOUS MOTORS
12
The following motors are permanent magnet synchronous motors that do not require gearing. These motors are technologically more complex than asynchronous motors, as described in section 6.3.
• •
Using the Keypad Plus:
Pr 0.48=SERVO
Using the Orona MT:
TMR 5.1 Mode = Servo
12
To control them, the drive should be configured in SERVO mode:
‘ORIGINAL’ M33 MOTORS
G_
IN
The ‘original M33’ are gearless synchronous motors supplied by Reivaj. They can work with an ARCA I controller (in which case a contactor box is raised above the machine as in the figure) or an ARCA II (contactors on drive board). The drive is always on a shaft board.
20
JUNE 2003 – JUNE 2007
LI
FT
They always use Warner drum brakes. These brakes require overexcitation, that is, a high voltage to open (205Vdc) and a lower voltage to keep open without getting hot. Brake plates 5124107 (ARCA I) and 5124356 (ARCA II) are used to achieve this.
Resistance
GA
RD
Poles
rpm nominal
148d 14.8 1103m 1.103 13518m 13.518
IN
Inductance
Nom. Voltage
92d 9.2 2495m 2.495 35914m 35.914
ER
Nom current
4-6p 1.6m/s
191
8p 1m/s
8p 1.6m/s
10-13p 1m/s
10-13p 1.6m/s
124d 12.4 1631m 1.631 27600m 27.6
179d 17.9 703m 0.703 9892m 9.892
180d 18 959m 0.959 17121m 17.121
280d 28 410m 0.41 6594m 6.594
191
306
6 12 390 306
Gain.P.curr Gain.I.curr
191
306 307 812
AN
TH
ON
Y_
TMR 5.5.2 Pr 0.46 TMR 5.5.2 Pr 5.17 TMR 5.5.2 Pr 5.24 TMR 5.5.2 Pr 0.42 TMR 5.5.2 Pr 0.44 TMR 5.5.2 Pr 5.08 TMR 5.5.2 Pr 0.38 TMR 5.5.2 Pr 0.39
4-6p 1m/s
_T
Lift type
AG
These are the only cases where the drive operates without PLC software.
0466017 - Unidrive SP – Lift Speed Control System
16/83
#ANTHONY_GARDINER_TAGLIFTING_201212# ADVANCE PARAMETER ADJUSTMENT EXTENDED M33 MOTORS
OCTOBER 2004 – DECEMBER 2006
21p 1.6m/s
Nom current
201d 20.1 655m 0.655 10077m 10.077
321d 32.1 287m 0.287 5018m 5.018
260d 26 529m 0.529 8272m 8.272
435d 43.5 224m 0.224 3238m 3.238
Resistance Inductance
239
383
6 12
Nom. Voltage
IN
Poles
rpm nominal
239
383
Gain.P.curr
FT
390
Gain.I.curr
812
LI
307
AG
TMR 5.5.2 Pr 0.46 TMR 5.5.2 Pr 5.17 TMR 5.5.2 Pr 5.24 TMR 5.5.2 Pr 0.42 TMR 5.5.2 Pr 0.44 TMR 5.5.2 Pr 5.08 TMR 5.5.2 Pr 0.38 TMR 5.5.2 Pr 0.39
12
21p 1m/s
20
16p 1.6m/s
G_
16p 1m/s
Lift type
12
Extended M33 motors are also gearless synchronous motors supplied by Reivaj. They use Warner round disk brakes (require overexcitation, plate 5124356). Always ARCA II controller (contactors and drive in shaft).
OPTIMIZED M33 MOTORS
FROM OCTOBER 2006
ER
_T
Optimized M33 motors are gearless synchronous motors, but supplied by Lancor. They all use Mayr square disk brakes, with the encoder located between the brakes, and the brakes do not require overexcitation (plate 5124375).
RD
IN
Always ARCA II controller (although the electrical installation is quite different from the 2 previous cases) and cover the same load and speed ranges.
6p 1ms
6p 1.6ms
8p 1ms
8p 1.6ms
13p 1ms
13p 1.6ms
16p 1ms
16p 1.6ms
21p 1ms
21p 1.6ms
80d
125d
105d
170d
165d
260d
215d
320d
255d
410d
8
12.5
10.5
17
16.5
26
21.5
32
25.5
41
TMR 5.5.2 Resistance Pr 5.17
3010m
1110m
1810m
781m
1212m
454m
843m
365m
665m
300m
3.01
1.11
1.81
0.781
1.212
0.454
0.843
0.365
0.665
0.3
TMR 5.5.2 Inductance Pr 5.24
35700m
13060m
26240m
9733m
18175m
6680m
13620m
5223m
10559m
4367m
35.7
13.06
26.24
9.733
18.175
6.68
13.62
5.223
10.559
4.367
GA
Lift type
ON
Y_
TMR 5.5.2 Nom current Pr 0.46
AN
TH
TMR 5.5.2 Poles Pr 0.42 TMR 5.5.2 Pr 0.44 TMR 5.5.2 Pr 5.08 TMR 5.5.2 Pr 0.38 TMR 5.5.2 Pr 0.39
8 16
Nom. Voltage rpm nominal Gain.P.curr Gain.I.curr
390 239
383
239
383
239
383
239
383
239
383
269
125
198
141
264
112
198
121
178
117
1942
909
1168
969
1504
653
1046
725
957
685
0466017 - Unidrive SP – Lift Speed Control System
17/83
#ANTHONY_GARDINER_TAGLIFTING_201212# ADVANCE PARAMETER ADJUSTMENT M34 MOTORS
FROM APRIL 2009
12
M34 motors are also Lancor gearless synchronous motors, although their layout is different, with the pulley between the motor and brakes. They use Mayr square disk brakes (no overexcitation, plate 5124375).
Resistance Inductance
80d 8 4440m 4.44 84700m 84.70
93d 9.5 2780m 2.78 61340m 61.34 8 16
Nom. Voltage
IN
Poles
20
Nom current
8p 1m/s
390
rpm nominal Gain.P.curr
FT
147
Gain.I.curr
LI
475 1566
AN
TH
ON
Y_
GA
RD
IN
ER
_T
AG
TMR 5.5.2 Pr 0.46 TMR 5.5.2 Pr 5.17 TMR 5.5.2 Pr 5.24 TMR 5.5.2 Pr 0.42 TMR 5.5.2 Pr 0.44 TMR 5.5.2 Pr 5.08 TMR 5.5.2 Pr 0.38 TMR 5.5.2 Pr 0.39
4-6p 1m/s
G_
Lift type
12
Work with ARCA II controller, but in this case the drive is located on the control board.
0466017 - Unidrive SP – Lift Speed Control System
18/83
#ANTHONY_GARDINER_TAGLIFTING_201212# ADVANCE PARAMETER ADJUSTMENT GEARLESS LEROY-SOMER MOTORS
FROM FEBRUARY 2007
1000kg 2.5ms
TMR 5.5.2 Nom current Pr 0.46
313d
310d
466d
520d
350d
31.3
31
46.6
52
35
TMR 5.5.2 Resistance Pr 5.17
699m
451m
358m
316m
451m
0.699
0.451
0.358
0.316
0.451
32743m
12957m
13121m
13061m
12957m
32.743
12.957
13.121
13.061
12.957
TMR 5.5.2 Inductance Pr 5.24 TMR 5.5.2 Poles Pr 0.42
Gain.I.curr
Number of poles: 32
72.1
115.3
115.3
115.3
380
173
228
227
1388
1030
1066
941
GEARLESS ZIEHL-ABEGG MOTORS
180.2
LI
Gain.P.curr
390
173
AG
rpm nominal
FT
Nom. Voltage
If the motor is not listed in the table: Rated current: as indicated on motor rating plate.
32
1030
Rated rpm: according to table 4.5.1. Rest: perform static auto tuning (see 5.2.2) FROM JANUARY 2009
_T
TMR 5.5.2 Pr 0.44 TMR 5.5.2 Pr 5.08 TMR 5.5.2 Pr 0.38 TMR 5.5.2 Pr 0.39
16
12
2500kg 1.6ms
20
2000kg 1.6ms
G_
1425kg 1.6ms
IN
2000kg 1ms
Lift type
12
Leroy-Somer Z6 and Z10 machines are permanent magnet synchronous motors that are distinguished by having the rotating part of the motor on the outside. They have Warner calliper brakes (2, 3 or 4 depending on load) that require overexcitation (plate 5124382).
TMR 5.5.2 Nom current Pr 0.46
1250kg 1ms
RD
630kg 1ms
Lift type
IN
ER
Ziehl-Abegg Zetatop machines are also permanent magnet synchronous machines. Depending on load they use Mayr or Warner square or round disk brakes but always with no overexcitation (plate 5124375). 2500kg 1ms
1800kg 1.6ms
300d
430d
430d
540d
23
30
43
43
54
TMR 5.5.2 Resistance Pr 5.17
1810m
1450m
587m
730m
587m
1.81
1.451
0.587
0.73
0.587
TMR 5.5.2 Inductance Pr 5.24
26240m
40804m
32743m
19061m
7408m
26.24
40.804
32.743
19.061
7.408
Y_
GA
230d
ON
TMR 5.5.2 Poles Pr 0.42 TMR 5.5.2 Pr 0.44 TMR 5.5.2 Pr 5.08 TMR 5.5.2 Pr 0.38 TMR 5.5.2 Pr 0.39
TH
AN
1600kg 1ms
10
rpm nominal Gain.P.curr Gain.I.curr
Rated current: as indicated on motor rating plate.
20
Nom. Voltage
If the motor is not listed in the table:
390
Number of poles: 20 Program according to speed table under 4.5.1 198
880
395
407
395
1168
5335
1337
2642
1338
0466017 - Unidrive SP – Lift Speed Control System
Rated rpm: according to table 4.5.1. Rest: perform static auto tuning (see 5.2.2)
19/83
#ANTHONY_GARDINER_TAGLIFTING_201212# ADVANCE PARAMETER ADJUSTMENT
4.3. ENCODER CONFIGURATION
AB
SC Hiper
SC EnDat
1024
1024 *
2048 *
15V **
8V **
5V **
Cable 1
fase 3
fase 3
Type Lines Tension alim. Detec.error
(*) Adjusts automatically
12
Stegman Absolute
(**) Attention: incorrect adjustment of this paramter can damage the encoder.
20
Stegman Absolute
G_
TMR 5.7.1 Pr 3.38 TMR 5.7.1 Pr 3.34 TMR 5.7.1 Pr 3.36 TMR 5.7.1 Pr 3.40
Increment al
IN
Parameter
12
As a function of the type of motor to be controlled, the following encoders are used:
4.3.1. INCREMENTAL ENCODER
LI
FT
Used to control all asynchronous machines. Almost always Heidenhain and there are 2 models that only differ in their assembly method: ERN430 (hollow axle, used in M322) and ROD436 (overhanging axle, used in the rest).
_T
4.3.2. STEGMAN ABSOLUTE ENCODER
AG
This encoder only measures speed, it cannot determine the position of the motor rotor.
ER
The Stegman SRS50 encoder is used in all M33 original, M33 extended, M33 optimized and M34 lifts. This encoder has a type of communication known as Hiperface with the drive which automatically adjusts Pr 3.33, 3.34 and 3.35.
GA
RD
IN
This encoder is absolute, and therefore in addition to speed it measures absolute rotor position. This is necessary to control synchronous motors, as described in 6.3. There are two codes (see 8.3.8) because the mechanical union can be with a splinted (M33 original or extended) or conical shaft (rest), but are electrically identical. 4.3.3. HEIDENHAIN ABSOLUTE ENCODER
ON
Y_
The ECN413 absolute encoder is used on all gearless Leroy-Somer and Ziehl-Abegg lifts. It is very similar to the Stegman, but Heidenhain uses a different communications protocol (called EnDat). Pr 3.33, 3.34 y 3.35 are also automatically configured.
AN
TH
4.4. OPERATING SEQUENCE There are two different operating sequences: one for the ‘M33 original’ (as it does not use PLC or DPL) and another for the rest. Adjustment of the drive operating sequence is quite delicate as it has to be ensured that: • • •
When opening the brake that the motor has sufficient current to not be overwhelmed by the load. When dropping the contacts current must be 0 (or a strong noise heard in the car) When closing the brake that the car is totally immobile (and therefore must wait until it has closed before lowering the current to 0).
0466017 - Unidrive SP – Lift Speed Control System
20/83
#ANTHONY_GARDINER_TAGLIFTING_201212# ADVANCE PARAMETER ADJUSTMENT 4.4.1. NORMAL OPERATING SEQUENCE C1+C2 Inputs
010
000
B1, B2, B3 Inputs
T contactor drop (controlled by
20
controler)
12
111
12
Ascend/Descend Inputs
Secure-Disable (Pr 0.29 or TMR 3.1 Secure-Disable) V0
VNULL
Speed Level (Pr 0.14 or TMR 3.1 Level)
G_
Vmax
Brake activation (Pr 0.22 or TMR 3.2 Brake output)
FT
Trip_End_T *
Par max
LI
Brake_Open_T*
IN
Torque ramp (Pr 19.47)
Current limit (Pr 0.06)
Torque_T *
Vmax
AG
Torque_T *
(*) These times can be changed on TMR 5.4.1 or Keypad Plus (see next page)
_T
Trip_Start_T *
Brake_Fall_T *
B
C
D
E
F
H
I
J
Speed reference (Pr 0.11)
G
Sequence Stages
RD
IN
A
ER
V0
The sequence starts when the drive receives a direction set point, Secure-Disable and speed level distinct from Vnull (in the example, Vmax) from the controller. In the case of asynchronous motors, it waits until the motor is magnetized. With synchronous motors it jumps directly to point B.
B
The torque ramp signal is activated (Pr 19.47). This raises the current limit (Pr 0.06) from 0 to the maximum permitted (Pr 0.58) for a length of time called Torque_T. (Pr 0.52). If this ramp is not used and the current is applied suddenly there would be noise and vibration in the car.
C
After a period of time Brake_open_T. (Pr 0.51) has elapsed since B, the brake open signal is activated (Pr 0.22). The brake will still then take some time to open mechanically, and it is important that when it opens completely that the ramp has completed otherwise the imbalance could overwhelm the car.
D
After a period of time Trip_Start_T. (Pr 0.53) has elapsed since B, the motor is allowed to accelerate. The brake must now be completely open, otherwise drag will be felt.
E
The drive decelerates to approach speed (commanded by the controller)
F
The drive decelerates to zero speed (commanded by the controller)
G
When the speed descends below a value (Pr 12.45) the stop sequence is initiated.
H
After a period of time Brake_Fall_T (Pr 0.54) has elapsed since G, the brake output is disconnected (Pr 19.46). It must be borne in mind that the mechanical closing of the brake will take a little longer.
I
After a period of time Trip_End_T (Pr 0.55) has elapsed since the start of stage G, the torque ramp signal is disconnected (Pr 19.47). This ensures that the current limit (Pr 0.06) goes down to 0 the same as in B. It is important that the ramp not start until the brake is completely closed or the car could move due to imbalance.
J
The current limit reaches 0 and therefore there ceases to be current in the motor.
K
The controller disconnects the contactors after the Caída Cont. [Cont. Drop] time has elapsed following point F.
AN
TH
ON
Y_
GA
A
0466017 - Unidrive SP – Lift Speed Control System
21/83
#ANTHONY_GARDINER_TAGLIFTING_201212# ADVANCE PARAMETER ADJUSTMENT The table displays the default values and how to make time adjustments. For example, if Brake_Open_T is increased, Trip_Start_T must be increased by the same amount: Adjustment of sequence times
Trip_End_T Torque_T
Contactors Drop Time
15d
0m 0 5d 0.5 3d 0.3 500m 500 0d 0
20d
20d
15d
12
500m 500 8d 0.8 2d 0.2 250m 250 6d 0.6
If increased, increase Travel_Start_T. If reduced, reduce Torque_T. If reduced, reduce Torque_T and Brake_Open_T If increased, watch out for sliding faults. If increased, increase Contactors_Drop_Time. If reduced, watch out it doesn’t fall during operation If increased, increase Contactors_Drop_Time. Never reduce it (may produce hits at stop) If increased, increase Contactors_Drop_Time, Trip_Start_T, Brake_Open_T. If reduced, increase Trip_End_T. Can be increased, never reduced. This parameter is in TM CONTROLLER 5.3.3
12
Brake_Fall_T
200m 200 10d 1 5d 0.5 200m 200 6d 0.6
Adjustments to perform if the parameter value is changed (always by the same amount)
20
Trip_Start_T
M322 y SM
G_
Brake_Open_T
M33 Ext
IN
TMR 5.4.1 Pr 0.51 TMR 5.4.1 Pr 0.53 TMR 5.4.1 Pr 0.54 TMR 5.4.1 Pr 0.55 TMR 5.4.1 Pr 0.52
L.Somer Z.Abegg
FT
M33 Opt, M34 200m 200 8d 0.8 0d 0 200m 200 6d 0.6
Parameter
4.4.2. M33 ORIGINAL OPERATING SEQUENCE
LI
The operating sequence for the ‘M33 original’ was simpler. It doesn’t use a torque ramp on start or stop, and therefore the current limit (Pr 0.06) is always fixed at 175%.
_T
AG
On start, the drive activates the brake output upon receipt of the SecureDisable signal. When the brake opens mechanically, the B1,B2,B3 speed signals arrive and acceleration commences:
RD
IN
ER
Time it takes the brake to open
111
GA
*
(*) In M33 ARCA I lifts, the brake micro switches cut levels B1,B2,B3 (see 0451118), and therefore in this area levels are at 000 (until the brake opens).
Ref. Speed (Pr 0.11)
SecureDisable Input B1,B2,B3 Inputs Brake output (Pr 0.22)
ON
Y_
On stop, the brake output is deactivated for a time (Pr 0.23) after the controller removes levels B1,B2,B3. This period should be less that the controller contactor drop period to ensure that the brake is closed when current ceases to be applied. MTControl: 5.3.3 Contactor Drop Time = 12d
TH
Pr 0.23 = 0.7
AN
Ref. Speed (Pr 0.11) SecureDisable Input 101
000
B1,B2,B3 Inputs Brake output (Pr 0.22)
0466017 - Unidrive SP – Lift Speed Control System
22/83
#ANTHONY_GARDINER_TAGLIFTING_201212# ADVANCE PARAMETER ADJUSTMENT
4.5. SPEED PROFILES 4.5.1. SPEED REFERENCES
Value Pr 0.14
TMR 3.1 Level
1 2 3 4 5 6 7 8
Vnull V00 V0 Vinsp V1 V2 V3 Vmax
12
27 0 1 0 1 0 1 0 1
20
Lift stopped Fine isoleveling Creep Speed Inspection/Emergency Intermediate speed 1 Intermediate speed 2 Intermediate speed 3 Maximum Speed
Terminal 28 0 0 1 1 0 0 1 1
G_
29 0 0 0 0 1 1 1 1
IN
Selected speed level
12
The controller chooses the speed at which the motor should operate at each moment via 3 digital inputs as follows:
The speed levels for each of them can be modified in the following parameters:
FT
5.2 5.2 5.2 5.2 5.2 5.2 5.2 5.2
AG
Stopped (should be 0) Fine isoleveling Creep Speed Inspection/Emergency Intermediate speed 1 Intermediate speed 2 Intermediate speed 3 Maximum Speed
TMR (mm/s) Vnull V00 V0 Vinsp V1 V2 V3 Vmax
LI
Keypad Parameters Original (rpm) Copy (m/s) * Pr 1.21 Doesn’t exist Pr 0.15 Pr 2.22 Pr 0.16 Pr 2.23 Pr 0.17 Pr 2.24 Pr 0.18 Pr 2.25 Pr 1.26 Pr 2.26 Pr 1.27 Pr 2.27 Pr 0.19 Pr 2.28
Speed level
(*) This copy is only avialable in drives with SMApps.Lite. See section 0.
ER
11.8
1
147
2.9
11.8
69
2
239
3.8
18
112
2
383
3.8
18
112
200
2
191
4
16.0
90
200
2
306
4
16.0
90
160
2
239
5
20
112
1.6
160
2
383
5
20
112
1
530
2
72.1
1.4
5.5
34
1.6
530
2
115.3
1.4
5.5
34
72.1
2.5
530
2
180.2
1.4
5.5
34
72.1
1
320
1
60
1
4.5
28
1.6
320
1
95
1
4.5
28
1
320
2
119
1.8
9
56
130
M34
1
130
M33 Opt.
1
160
1.6
160
M33 Original
1 1.6
M33 Ext.
1
Leroy Somer
TH
ON
Ziehl-Abegg
1
93
IN
0.63
RD
Nuevo Renova
AN
MT 5.5.2 MT 5.2 (mm/s) rated V00 V0 Vinsp V1 V2 Vmax rpm 18 70-80 470 1000 1600 varía Pr 5.08 Pr 0.15 Pr 0.16 Pr 0.17 Pr 0.18 Pr 1.26 Pr 0.19
GA
Rated Pulley speed diam. Susp (m/s) (mm)
Y_
Lift model
_T
The following table contains speed values for gearless motors:
2.9
69
93 147
1.6
320
2
191
1.8
9
56
1
400
1
48
0.7
3.6
22
1.6
400
1
76
0.7
3.6
22
1
400
2
95
1.5
7.2
45
1.6
400
2
153
1.5
7.2
45
1
450
2
85
1.3
6.5
40
1.6
450
2
136
1.3
6.5
40
239 239
382 191
191
306 239
239
382 72.1 115.3 115.3
180.2 60
60
95 119
119
191 48
48
76 95
95
153
84.9
136
85
It must be borne in mind that the maximum values for these parameters are limited by Pr 0.02 (TMR 5.6.1 rpm max). This parameter is always set at 10rpm above the motor rated speed (Pr 5.08 or TMR 5.5.1 rpm nominal). 0466017 - Unidrive SP – Lift Speed Control System
23/83
#ANTHONY_GARDINER_TAGLIFTING_201212# ADVANCE PARAMETER ADJUSTMENT The following table contains speed values for geared motors:
(m/s po ) les
pulley (mm) Susp
V00 30 Pr 0.15
V0 100 Pr 0.16
TMR Vinsp 600 Pr 0.17
5.2 (mm/s) V1 V2 1000 1600 Pr Pr 0.18 1.26
V3 2000 Pr 1.27
Vmax varies Pr 0.19
TMR 5.3 (mm/s2 y mm/s3) Accel/ Decel Jerk travel 800 1000 Pr Pr 0.03, 0.04 0.20, 2.18
12
Speed No. Reduc Diam.
TMR 5.6.1 rpm max Pr 0.02
4
60:1
500
1
1444
69
229
1375
1444
0.545
0.436
0.63
4
55:1
450
1
1471
70
233
1401
1471
0.536
0.428
0.63
4
39:1
650
2
1444
69
229
1375
1444
0.545
0.63
4
39:1
600
2
1564
74
248
1490
1500
0.503
0.63
4
45:1
750
2
1444
69
229
1375
1444
0.545
0.63
4
39:1
600
2
1564
74
248
1490
1500
0.503
0.403
0.63
4
72:2
600
2
1444
69
229
1375
1444
0.545
0.436
0.63
4
60:1
550
1
1313
63
208
1250
1313
0.600
0.480
0.63
4
50:2
630
2
955
45
152
909
955
0.825
0.660
0.63
4
62:2
500
2
1492
71
237
1421
1492
0.528
0.422
0.63
4
60:1
500
1
1444
69
229
1375
1444
0.545
0.436
0.63
4
60:1
450
1
1604
76
255
1500
1500
0.491
0.393
1
4
45:1
550
1
1563
47
156
938
1500
0.800
0.640
1
4
45:1
570
1
1508
45
151
905
1500
0.829
0.663
1
4
47:2
600
2
1496
45
150
898
1496
0.836
0.668
1
4
53:2
700
2
1446
43
145
868
1446
0.864
0.692
1
4
53:2
650
2
1557
47
156
934
1500
0.803
0.642
1
4
39:1
600
1
1241
37
124
745
1241
1.007
0.806
1
4
39:2
500
2
1490
45
149
894
1490
0.839
0.671
1
4
48:1
700
1
1310
39
131
786
1310
0.954
0.764
1
6
37:2
340
1
1039
31
104
624
1039
1.203
0.962
1
4
55:2
340
1
1545
46
154
927
1500
0.809
0.647
1
4
41:3
340
2
1535
46
154
921
1500
0.814
0.651
1.6
4
47:2
530
1
1355
25
85
508
847
1355
1.476
1.181
1.6
4
53:2
600
1
1350
25
84
506
844
1350
1.482
1.186
1.6
4
53:2
650
1
1246
23
78
467
779
1246
1.605
1.284
1.6
4
47:3
650
2
1473
28
92
552
921
1473
1.358
1.086
1.6
4
39:2
800
2
1490
28
93
559
931
1490
1.343
1.074
1.6
4
67:4
700
2
1462
27
91
548
914
1462
1.368
1.094
1.6
4
72:2
700
1
1572
29
98
589
982
1500
1.273
1.018
1.6
4
53:2
700
1
1157
22
72
434
723
1157
1.729
1.383
2
4
53:2
650
1
1557
23
78
467
779
1246
1500
1.605
1.284
2
4
53:2
700
2
4
47:2
650
2
4
47:2
600
2.5
4
22,9:1
20
G_
IN FT LI
AG
_T
ER
IN
RD
0.436 0.403 0.436
1
1446
22
72
434
723
1157
1446
1.729
1.383
1
1381
21
69
414
690
1105
1381
1.810
1.448
1
1496
22
75
449
748
1197
1496
1.671
1.337
1519
18
61
365
608
972
1500
2.057
1.646
GA 720
12
0.63
1
1215
Y_
It is important to first adjust parameter Pr 0.02 (TMR 5.6.1 rpm max) because it limits the value of the other parameters.
ON
4.5.2. ACCELERATIONS AND JERKS
AN
TH
The values for acceleration, deceleration and jerk determine how speed varies from one level to another when the controller changes the speed set point. These values can be modified within a margin:
•
Increasing acceleration requires more torque from the motor, and it is therefore not recommended it be increased more than 0.1m/s2 above the default value.
•
Reducing deceleration (and also acceleration, to a lesser extent) forces deceleration distances to be increased for all speeds (MT Control, 5.4.3.1 Dist.Dec.).
•
Jerk influences both comfort during speed changes and deceleration distances and stopping precision. Do not lower it below 1m/s3 or raise it above 3m/s3.
0466017 - Unidrive SP – Lift Speed Control System
24/83
#ANTHONY_GARDINER_TAGLIFTING_201212# ADVANCE PARAMETER ADJUSTMENT The following figures illustrate the effect of these parameters: Speed profile (no jerk limit)
Deceleration
12
Travel Jerk
*
IN
G_
20
12
Acceleration
Speed profile (with jerk limit)
(*) The stop jerk is controlled from a different parameter depending on the type of machine:
FT
For M33 extended lifts, M322 lifts or lifts with a machine room: Pr 2.18
For M33 original lifts: Pr 0.20 (cannot be adjusted separately from travel jerk). For the rest (Optimized M33, M34, Leroy-Somer and Ziehl-Abegg). Pr 18.26
LI
• • •
AG
In addition to the Keypad Plus, these parameters can be modified in TMR 5.3 Acceleration, Deceleration (mm/s2), Jerk Travel and Jerk Stop (mm/s3). Remember that M33 originals and M33 extended cannot perform this communication.
Pr 0.03 or 0.04 = table value x 0.8/acceleration desired (in m/s2) Pr 0.20 or 2.18 = table value/jerk desired (in m/s3)
ER
• •
_T
Default values for geared synchronous machines appear in the table on the previous page. If it is necessary to modify these values, do so as follows:
For gearless synchronous motors, acceleration and jerk values are as follows: M33 Opt. 160 2 6.98 5.98 5.24 4.65 4.19 458 686 763 915 1144 1373 1716
AN
TH
ON
Y_
GA
RD
IN
M34, Lift model: Renova Pulley diam. (mm) 130 Suspension 1 600 11.34 Acceler. and 700 9.72 deceleration 800 8.51 (mm/s2) 900 7.56 1000 6.81 3000 743 Jerk travel 2000 1115 and stop 1800 1239 (mm/s3) 1500 1487 1200 1859 1000 2230 800 2788
M33 Original 200 2 8.73 7.48 6.54 5.82 5.24 385.0 379.1 376.7 372.1 365.1 358.1 347.6
M33 Ext. 160 2 6.98 5.98 5.24 4.65 4.19 1.396 2.094 2.327 2.793 3.491 4.189 5.236
LeroySomer 530 2 23.1 19.8 17.3 15.4 13.9 1516 2273 2526 3031 3789 4547 5683
Ziehl-Abegg 320 1 27.9 23.9 20.9 18.6 16.8 1830 2745 3050 3660 4575 5490 6863
320 2 14.0 12.0 10.5 9.3 8.4 915 1373 1525 1830 2288 2745 3431
400 1 34.9 29.9 26.2 23.3 20.9 2288 3431 3813 4575 5719 6863 8578
400 2 17.5 15.0 13.1 11.6 10.5 1144 1716 1906 2288 2859 3431 4289
450 2 19.6 16.8 14.7 13.1 11.8 1287 1930 2145 2574 3217 3860 4825
Default values are shaded (note that the default value in M33 original and extended lifts is 2m/s3 and in the rest it is 1m/s3). In lifts with the SM-Apps.Lite card, a coy of the programmed values can be queried (as described in section 5.3.5):
• •
Pr 2.12 / 2.13: acceleration/deceleration in m/s2 Pr 2.14 / 2.15: jerks travel/stop in m/s3
0466017 - Unidrive SP – Lift Speed Control System
25/83
#ANTHONY_GARDINER_TAGLIFTING_201212# ADVANCE PARAMETER ADJUSTMENT
4.6. INERTIA COMPENSATION
450
12
Car and counterweight inertia in the lift application is very large. This can make the motor struggle to keep up with the set point, as illustrated in the following image:
400
12
Actual real speed Velocidad Set point speed Velocidad Consigna Torque required Par requerido
350
20
300 50
250
G_
45 40
200
35
150
IN
30 25
100
15
50
10 5
0
2
4
6
8
10
0
12
LI
0
FT
20
0
2000
14
4000
6000
8000
10000
12000
14000
AG
If an inertia value (in kgm2) is programmed and inertia compensation is activated (Pr 4.22=1), the drive applies more torque during speed changes (the greater the more inertia programmed), allowing the speed profile to follow the set point.
_T
This function is factory programmed on optimized M33, Leroy Somer, Ziehl-Abegg and M34 lifts.
ER
4.7. SPEED CONTROL
Lifts with M.Room
M322
M33 Original, M33 Opt, M34
M33 Extended
Leroy-Somer Ziehl-Abegg
Pr 0.07
0.12 (210m)
0.12 (120m)
0.21 (210m)
0.15
0.3 (300m)
Pr 0.08
2 (200c)
0.1 (10c)
1 (100c)
1
4 (400c)
Pr 0.28
4ms
1ms
1ms
1ms
1ms
Keypad Plus
GA
TMR 5.4.2
RD
IN
The Unidrive SP drive always attempts to adjust motor speed (which it reads via the encoder) as best as possible to the reference (generated by the set point selected by the controller with drive programmed acceleration/deceleration ramps). This tracking is adjusted via the Speed Control parameters.
Gain P.
Y_
Gain I.
AN
TH
ON
Enc. filter
PRECAUTION Changing these parameters may cause very strong oscillations in the car, and it is therefore recommended that the default values are used. If motor noise or cabin vibration problems are present, consult section 6.4.
4.8. CURRENT CONTROL (TORQUE) To ensure that motor speed adjusts to the set point, what happens is that the drive adjusts output current, because this translates into torque. That is, if the drive sees that the speed is below the reference, it applies more current (torque) to the motor for it to reach it.
0466017 - Unidrive SP – Lift Speed Control System
26/83
#ANTHONY_GARDINER_TAGLIFTING_201212# ADVANCE PARAMETER ADJUSTMENT PRECAUTION The parameters that adjust this control (gain and filter) are delicate and it is not recommended that default values are changed. Gain changes for each motor and therefore appear in section 9.2.
12
12
The switching frequency affects the waveform of the voltage applied by the drive, which causes resonance in the motor coils and can be heard as a sharp whistle. If it is increased to 12-16kHz the sound becomes inaudible but electromagnetic emissions get worse.
20
The torque limit can be increased to attempt to unwedge the lift, but for normal operation the default value should not be raised. Keypad Plus
Geared Motor (M322 and SM)
M33 Original
M33 Ext, M34, M33 Opt, Nuevo Renova
Leroy-Somer Ziehl-Abegg
Filter curr.
Pr 4.12
2 (20d)
0
0
2 (20d)
Conmut. Freq
Pr 0.41
Torque Limit
Pr 0.58*
8kHz 175
175
IN
225
G_
(depends on motor type)
TMR 5.6.1 or 5.6.2
175
FT
(*) On M33 original lifts this parameter was Pr 0.06 instead of Pr 0.58.
LI
4.9. START COMPENSATION
AG
To achieve good start comfort, "normal" speed control is not sufficient, because due to the imbalance between the car and the counterweight the lift can move a lot (even touching a limit stop if at a terminal floor). This movement is greater in gearless lifts. The figure illustrates how, without load compensation, movement is produced in the car at the start.
2 strategies can be employed: load compensation or position control (the latter is not available for ‘M33 original’ lifts). Both strategies only influence the start (until the drive commences the acceleration profile).
To activate load compensation, program TMR 5.4.4 Position Control = [NO] (Pr 0.57=0). To deactivate it and use position control, set it to [YES] (Pr 0.57=1).
GA
RD
IN
ER
_T
Speed reference Actual speed Current Secure-Disable
Y_
4.9.1. POSITION CONTROL
AN
TH
ON
This type of strategy does not require loadweights, but does not achieve such a good in-car comfort level (a small bump can be felt on start). It consists of correcting any movement by rapidly applying a current impulse, so that the axis hardly moves. Used as standard in all M34, Nuevo Renova, M322 and Machine Room lifts. For the rest it can be activated if there are problems with loadweights, although comfort is lost. It is possible to adjust Pr 13.09 to attempt to make control more or less rigid. Can only be used in drives with firmware version 1.05 or later (Pr 0.50 or TMR 3.1 Software).
0466017 - Unidrive SP – Lift Speed Control System
27/83
#ANTHONY_GARDINER_TAGLIFTING_201212# ADVANCE PARAMETER ADJUSTMENT 4.9.2. LOAD COMPENSATION
12
12
Load compensation requires loadweights (Micelect or Orona) that tell the drive how much load the car contains via an analogue input (0-100%). Thereby, when the drive opens the brake, it is already applying appropriate current to compensate the imbalance (as displayed in the figure) and the pulley hardly moves.
G_
20
This type of strategy is used in all M33 lifts (original, extended, optimized), the Leroy-Somer and ZiehlAbegg. It is important to highlight that the analogue signal from the Micelect loadweights takes the form of current (0-20mA) whilst for Orona loadweights it is voltage (0-10V).
FT
IN
To invert the compensation performed by the loadweights: • Using the Keypad Plus, change the sign for Pr 0.26 and invert Pr 7.13 • Using the TMR, invert 5.4.4 Comp. sign
LI
Default compensation and adjustment values must be sufficient to ensure good comfort, and can be consulted in section 9.2. TMR 5.4.4
Keypad Plus
Compensation
Pr 0.26
Ramp signal:
Comp. sign
Pr 7.13
Ramp slope:
Adjust
Pr 0.27
Value
Pr 7.11
0-20mA (Micelect) or Volt (Orona)
Analogue signal type
AI Mode
Left lifts
Right lifts
Positive value*
Negative value*
1
0
AG
Compensation with empty lift
_T
Parameter
ER
(*) When using TMR, the sign is already included in the parameter Comp. sign
IN
Calibration of load compensation:
RD
The default parameters programmed for the drive should be sufficient. If there is a lot of counter travel on opening the brake, first check that the loadweights measures correctly and that the counterweight is properly setup. If despite all this it is necessary to calibrate compensation: To calibrate 0 (compensation with car empty):
GA
6.
ON
Y_
a. Position the empty car at the top floor, place in emergency. b. Set inspection speed at 0 (TMR 5.2 Vinsp or Pr 0.17). Press descend on the operating panel, wait 3 seconds and make a note of the torque c. value and sign Pr 0.24 or TMR 3.1 Torque and Sign Torque). d. With this result, program Pr 0.26 (or TMR 5.4.4 Compensation and Sign.Comp). e. If the signal was positive, program Pr 7.13=1. If not, Pr 7.13=0 (with TMR not necessary, is automatically configured when changing Sign.Comp).
AN
TH
7.
To calibrate the ramp (compensation per kg of load): a. With the car at the top floor and inspection speed set to 0, insert full load. b. Press descend on the operating panel, wait 3 seconds and make a note of the torque value (Pr 0.24 or TMR 3.1 Torque). c. Add the value obtained from Pr 0.26 (TMR 5.4.4 Compensation), ignoring the signs obtained, and divide it by 80. d. Program the result from the operation in Pr 0.27 (or in TMR 5.4.4 Adjustment, but multiplying by 1000 because the MT is in thousandths).
8.
Undo change to Pr 0.17 and record parameters.
0466017 - Unidrive SP – Lift Speed Control System
28/83
#ANTHONY_GARDINER_TAGLIFTING_201212# ADVANCE PARAMETER ADJUSTMENT
4.10. BRAKING RESISTANCE
12
The braking resistance is responsible for dissipating the energy recovered by the motor when the car moves due to the load. To avoid the resistance burning itself, the drive controls the energy that it dissipates and gives a fault if this is excessive.
12
Parameter TMR 5.7.2 T.resist.frein. (Pr 10.30) regulates how much it can dissipate before providing the fault. The default value is 4. If the drive gives errors IT.Br and counterweight is correct, this value can be increased.
20
4.11. RESCUE OPERATION
DRIVE
LI
SUPPLY
FT
IN
G_
When the lift has an autonomous rescue system it uses a SAI (Uninterruptible Power Supply based on batteries) to power the drive in the absence of power supply. An autotransformer is necessary to raise the output voltage from the SAI from 220V to 380V (otherwise the drive will indicate a UV fault).
Transf.
AG
CONTACTORS C1 & C2
_T
UPS
ER
The values that play a role in a rescue are:
Pr 0.34 (TMR 5.4.3 Load Favour.dir): must be set to 1 (yes). When the drive reads that the rescue input is active, it automatically chooses the most favourable direction (depending on the car load). Cannot be set to 0 (no) if the SAI is not sized for this (special cases).
•
Pr 0.59 (TMR 5.4.3 Torque Limit): indicates the torque percentage that can be provided to the motor during the rescue operation. By default 100%, should never require a higher value (otherwise probably attempting to go against the load).
•
Pr 0.23 (TMR 3.2 Rescue): indicates if the drive detects that input 26 has been activated (which indicates that rescue mode is operational).
GA
RD
IN
•
Y_
4.12. RFC MODE
ON
RFC mode allows the drive to control asynchronous motors without an encoder, estimating motor speed based on internal current and voltage readings.
AN
TH
It is not recommended that it be used, other than to rule out problems with an encoder, because the comfort obtained is not optimum. Under no circumstances can it be sued with permanent magnet synchronous motors. To activate it:
•
Using the Keypad Plus: Pr 3.24=1 (activates the mode), Pr 3.40 = 0 (so drive does not give encoder faults).
•
Using TMR 5.6.1 Without enc. = Yes
0466017 - Unidrive SP – Lift Speed Control System
29/83
#ANTHONY_GARDINER_TAGLIFTING_201212# FUNCTIONS
5. FUNCTIONS
12
5.1. INVERSION OF DIRECTION OF ROTATION
12
Depending on the location of the machine in the shaft, it is necessary to change the rotation direction so that the car movement agrees with the controller signal.
20
5.1.1. M322 LIFTS AND LIFTS WITH MACHINE ROOMS
G_
To invert the direction of rotation in these lifts, it is sufficient to invert parameter TMR 4.2 Change Direction or Pr 0.33.
IN
5.1.2. M33 EXT, M33 OPT, LEROY-SOMER AND ZIEHL-ABEGG LIFTS
FT
In these cases it is necessary to invert, in addition to operating orders, the compensation that is applied as a function of the signal from the loadweights: Left
Right
Effect of changing
Pr 0.33
ON
OFF
Inverts the direction of rotation
Pr 7.13
ON
OFF
Inverts the compensation provided by the loadweights when the car has load
Pr 0.26
Positive value
Negative value
Inverts the compensation provided by the loadweights when the car is empty
_T
AG
LI
Parameter
The 3 parameters are automatically inverted if TMR 4.2 Rotation is inverted.
ER
5.1.3. M34 LIFTS
IN
In these cases loadweights are not used, and therefore to invert the direction of rotation it is sufficient to change Pr 0.33 or TMR 4.2 Rotation.
GA
RD
ATTENTION As the M34 is orientated differently depending on its position, these should always be programmed with TMR 4.2 Rotation = Izq [LEFT] (Pr 0.33 = On)
Y_
5.1.4. ‘ORIGINAL’ M33 LIFTS Here, as no PLC is present, it is necessary to change the following parameters: Left
Right
Effect of changing
Pr 7.10
6.32
6.30
Inverts the direction of rotation when controller orders Ascend.
Pr 7.18
6.30
6.32
Inverts the direction of rotation when controller orders Descend.
Pr 7.13
ON
OFF
Inverts the compensation provided by the loadweights when the car has load
Pr 0.26
Positive value
Negative value
Inverts the compensation provided by the loadweights when the car is empty
AN
TH
ON
Parameter
0466017 - Unidrive SP – Lift Speed Control System
30/83
#ANTHONY_GARDINER_TAGLIFTING_201212# FUNCTIONS
5.2. MOTOR AUTO TUNING The auto tuning or auto adjustment process serves to calculate:
•
Motor parameters (TMR 5.5.1 or 5.5.2): resistance (Pr 5.17), inductance (Pr 5.24) and:
Control parameters (TMR 5.6.1 or 5.6.2): Gain.P.curr (Pr 0.38) and Gain.I.curr (Pr 0.39). These parameters are very important to motor control, and the values calculated by the auto tuning tend not to be ideal, and therefore it is recommended to:
20
•
12
12
In the case of asynchronous motors: power factor (Pr 0.43). For synchronous motors: encoder reference angle (Pr 0.43). This parameter is fundamental for correctly controlling these motors, see section 6.3.
G_
Use those indicated in this standard for that motor or a similar one. Divide by 2 (motor up to 22kW) or 4 (motor over 22kW) the values calculated by the auto tuning where there is no data for a similar motor.
However, auto adjustment should be carried out when:
The motor is special and therefore its electrical parameters do not figure in the tables.
LI
• •
FT
IN
If the drive has been changed auto adjustment is not necessary (it is sufficient to copy the parameters from one to the other using the SmartCard or using the SM-Apps.Lite card reset to default parameters function).
A synchronous motor encoder has been manipulated (rotated or replaced).
AG
5.2.1. ROTARY AUTO TUNING
ER
_T
To perform this auto adjustment the traction cables must be unhooked because the motor needs to be able to rotate freely. For synchronous motors, this can be attempted with a balanced load in the centre of the shaft, but the estimated angle will be imprecise. For asynchronous motors it is impossible to perform directly with cables (it takes too long and it would crash). The rotary auto tuning process is as follows:
Put the lift in emergency mode.
2.
If using the TM, program TMR 4.1 Type = [Rot] and Execute = [YE] If using the Keypad Plus, program Pr 0.40=2 and Pr 8.11=on (the latter should not be performed for original ‘M33’ lifts).
3.
Press an emergency pushbutton (up or down) and keep it pressed until the drive finishes the auto tuning (approx. 40s). This can be observed because TMR 4.1 Status will change to inactive or the Keypad screen will display rdy.
4. 5. 6.
Make a note of the values obtained (especially the angle) and correct the gains. If Pr 8.11 has been modified, reset to off. Check for correct motor operation before hanging cables. A synchronous motor should consume (Pr 0.12) less than 1A, and an asynchronous one approximately half its rated current. Record parameters and SmartCard.
ON
Y_
GA
RD
IN
1.
AN
TH
If the auto tuning was performed with the Keypad Plus and it fails because the brake opens and closes repeatedly, repeat the entire process with Pr 8.11=off and setting Pr 8.21=8.09+ step 2. Upon completion of the process, reset 8.21=19.46+
in
in step 5.
5.2.2. STATIC AUTO TUNING This auto adjustment doesn’t need the motor to move and therefore cables don’t have to be unhooked. However, it doesn’t calculate the encoder reference angle (synchronous motors) and its power factor estimate (synchronous motors) isn’t as precise as with rotary auto tuning. 0466017 - Unidrive SP – Lift Speed Control System
31/83
#ANTHONY_GARDINER_TAGLIFTING_201212# FUNCTIONS To perform static auto tuning: Put the lift in emergency mode.
2.
If using the TM, program TMR 4.1 Type = [est] and Execute = [YE] If using the Keypad Plus, Pr 0.40 = 4 (synchronous motor) or 1 (asynchronous).
3.
Press an emergency pushbutton (up or down) and keep it pressed until the drive finishes the auto tuning (approx. 2s). This can be observed because TMR 4.1 Status will change to inact or the Keypad screen will display rdy.
4.
Make a note of the values obtained and correct gains if necessary. Store parameters.
20
12
12
1.
G_
5.3. SM-APPS.LITE SPECIAL FUNCTIONS
FT
5.3.1. ANGLE ESTIMATE (ONLY SYNCHRONOUS MOTORS)
IN
This section describes functions that are only available due to the software contained on the SM-Apps.Lite card. If the drive did not originally include this card, it can be added to provide these functions (in the case of ‘original’ M33 lifts, the only function that can be used is reset to default parameters).
LI
This function allows the encoder reference angle to be estimated (Pr 0.43) on a synchronous motor, in the same manner as when performing a rotary auto tuning but without having to unhook the traction cables.
_T
AG
A certain amount of imbalance is required for the estimate, therefore it is important to ensure that the brake opens and that the car and counterweight are not balanced (a good way of doing this is to test using manual rescue, the car moves). To perform the angle estimate:
Put the lift in emergency mode with the car empty. Leave a certain distance from the edges (the process will fail if the counterweight or car rest on the buffers).
2.
Set Pr 20.21 to 1
3.
Press an emergency pushbutton to initiate the process.
4.
During the process, the motor tends to become unstable, and therefore the drive and the lift controller report O.Spd errors. This doesn’t mean that the process has failed (these faults are automatically recovered and the process continues). The emergency pushbutton must remain pressed until the process finishes correctly (Pr 20.21 returns to 0) or the drive display shows a Tune fault (which indicates that the process has failed).
Y_
GA
RD
IN
ER
1.
If the process completes correctly, Pr 20.21 returns to 0 and the lift starts to move normally. Release the pushbutton to stop.
6.
Check that motor current consumption (Pr 0.12) is normal. With the car empty downwards, the value for Pr 0.12 should be approximately 80-90% of nominal motor current. To the contrary counterweight is incorrect or process has failed.
AN
TH
ON
5.
If the process fails continually with Tune or Tune2, it could be due to incorrect wiring of the output. Exchange two wires in the inverter output (for example, U and V) and try again. This function only provides an estimate and is therefore less precise than rotary auto tuning. If in doubt, unhook the cables and perform rotary autotuning. Having checked that the lift works perfectly with the new calculated angle, it is recommended it be phased to 0 as described in the following section.
0466017 - Unidrive SP – Lift Speed Control System
32/83
#ANTHONY_GARDINER_TAGLIFTING_201212# FUNCTIONS 5.3.2. ENCODER PHASING TO 0 (ONLY SYNCHRONOUS MOTORS)
12
This function moves the shaft of a synchronous motor to the position calculated by auto tuning (or angle estimate) above (position recorded in Pr 0.43) and phases the encoder to 0 in this position. In this manner, following execution, the angle to be set for Pr 0.43 to control that motor becomes 0.
12
This operation is carried out at the factory for all motors. However, if rotary auto tuning or angle estimate has been performed because the encoder has been changed or moved, phasing to 0 can also be used.
20
To execute this function:
Put the lift in emergency mode. Leave a certain distance from the edges (the process will fail if the counterweight or car rest on the buffers).
2.
Set Pr 20.25 to 1
3.
Press an emergency pushbutton (ascend or descend) to initiate the process.
4.
During the process, the motor will move by approximately one turn to place itself in the phasing position.
5.
If the process completes correctly, Pr 20.43 phases to 0, Pr 20.25 returns to 0 and the lift starts to move normally. To the contrary the drive returns a Tune fault.
FT
IN
G_
1.
AG
LI
Once finished, check that motor current consumption (Pr 0.12) is normal. Supposing the car is empty, use the emergency control panel to move the car down, the value for Pr 0.12 should be approximately 80-90% of nominal motor current.
_T
5.3.3. RESET TO DEFAULT PROGRAMMING
ER
The SM-Apps.Lite card memory contains a saved copy of default parameters for each Orona installation type. To restore them, proceed as follows:
IN
1. Stop the lift (place in emergency mode). 2. Program the lift type in Pr 19.14: M33 original
M33 ext.
101
111
LeroySomer
ZiehlAbegg
M34
Machine room
M322 1000rpm
M322 1500rpm
121
131
141
161
201
211
221
GA
Pr 19.14
M33 opt.
RD
Type
3. Program installation type in Pr 19.15:
Susp
ON
Red.
Y_
Asynchronous motors with machine room
Only standard parameters, upon completion of reset, have to program motor, speed, acceleration and jerk.
TH
AN
Speed Pulley Mot. m/s mm Pow. (cv)
47:2 45:1 47:2 45:1
2:1 1:1 1:1 1:1
1 1 1.6 1
600 570 530 570
7.5 10 15 rest 15 10 15 7.5
Pr 19.15
1 2 3 4 5 6 7 8
0466017 - Unidrive SP – Lift Speed Control System
Synchronous M322 Motors M. speed (rpm)
1000 1500
Persons
Reg.pow (kW)
Pr 19.15
4-6 8 4-6 8 10-13
5.5 7.5 5.5 7.5 11
1 2 1 2 3
33/83
#ANTHONY_GARDINER_TAGLIFTING_201212# FUNCTIONS
21 4-6 8 1,6
10-13 16 21
7 8 9 10 11 12 5 6 7 8
Gearless Leroy-Somer Machine Direction
Pr 19.15
1 1.6 1.6 1.s6
2000 1425 2000 2500
Right Right Right Right
1 2 3 4
Load (kg)
Susp.
Pulley (mm)
Direction
Pr 19.15
1 1 1 1 1 1.6
630 1250 1600 2000 2500 1800
1:1 1:1 2:1 2:1 2:1 2:1
318 318 318 392 395 444
Right Right Right Right Right Right
1 2 3 4 5 6
RD
IN
12
Speed
_T
Load (kg)
Gearless Ziehl-Abegg Machine
ER
Speed
2
12
1 2 3 4
1
20
16
M34
G_
10-13
M33 opt. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20
IN
8
M33 ext.
FT
4-6
1
M33 original 1 2 3 4 5 6
Direction Left Right Left Right Left Right Left Right Left Right Left Right Left Right Left Right Left Right Left Right
LI
Persons
AG
Speed
GA
These parameters are generally recorded at the factory for each type of installation, but it is important to check them before resetting. 4. Set Pr 0.00=1700.
Y_
5. Set Pr 19.40=on to initiate reset.
ON
6. The reset lasts approximately 30 seconds, on completion Pr 19.40 automatically returns to off. During the process faults may arise that will reset upon completion of the process (doesn’t mean it has failed).
AN
TH
If after 1 minute Pr 19.40 continues at on, the process has failed. Program Pr 19.40 = off, restart the SM-Apps.Lite card (Pr x.00=1070 +
) and restart from point 1.
7. After the resetting to default parameters, the SM-Apps.Lite card must be reset: Pr x.00=1070 +
.
8. After confirming that the lift works properly and that the programming is correct, parameters for Pr 0.00=1000 +
should be recorded.
This reset to default programming function CAN be used with M33 ‘original’ lifts (if an SM-Apps.Lite card is added to the drive). 0466017 - Unidrive SP – Lift Speed Control System
34/83
#ANTHONY_GARDINER_TAGLIFTING_201212# FUNCTIONS 5.3.4. FILTERING OF DIGITAL INPUTS
12
The controller controls the drive via 5 digital signals: 2 for direction and 3 for speed level. If due to electromagnetic problems one of these signals changes value, albeit briefly, the drive responds by starting a ramp. If this occurs near a speed change point, the lift can overrun its stop.
12
Using the calculation capacity of the SM-Apps.Lite card, these inputs are filtered, ignoring any change lasting less than 8ms.
20
5.3.5. UNIT CONVERSION
G_
The units used by the Control Techniques drive for speed, acceleration and jerk parameters are more geared to machine tools than lifts. To better see what effect these parameters have on the car, unit conversion has been implemented in the card (from rpm to m/s).
Keypad Plus Pr 19.18
:
Pr 19.19
Reduction
Pr 19.20
:
Pr 19.21
Pulley diameter (mm)
LI
Suspension
FT
Data
IN
To perform this conversion, the following input parameters are necessary (factory adjusted for most installations):
Pr 19.22
(*) For example, a lift with 2:1 suspension should be Pr 19.18=2 and Pr 19.19=1…
_T
AG
The speed “copy” parameters in m/s are described in section 4.5.1. Copies of accelerations (m/s2) and jerks (m/s3) are described in 4.5.2. It must be borne in mind that all these “copy” parameters are read only.
ER
5.3.6. COUNTERWEIGHT CALCULATION (ONLY GEARLESS MOTORS)
IN
On all lifts it is essential that the counterweight is correctly setup, because otherwise there may been problems with excessive heating or even destruction of the motor, the drive or (more commonly) the braking resistances.
RD
It is also important, especially to achieve good car comfort, that mechanical system assembly (guides, side bars, cables) is the best possible. This tends to measured by a variable called mechanical efficiency (a good value is 80% for M34 and 85% for the rest).
Y_
GA
This function allows mechanical efficiency to be calculated approximately and how much weight needs to be added to the counterweight without having to place a balanced load in the car. This can only be used in gearless lifts.
ON
This function requires the following parameters to be programmed (factory adjusted for most installations): Data
Correct value
Suspension
Pr 19.18 : Pr 19.19
1:1 for M34, 2:1 for M33 opt, variable (rest)
Reduction
Pr 19.20 : Pr 19.21
1:1 in all cases (they are gearless)
TH
AN
Keypad Plus
Pulley diameter (mm)
Pr 19.22
130 (M34), 160 (M33 opt), variable (rest)
Counterweight factor (%)
Pr 19.23
45% (M34), 50% (rest)
Motor rated torque (Nm)
Pr 19.24
Variable, get from rating plate
Lift rated load (kg)
Pr 19.25
-
To use this function: 0466017 - Unidrive SP – Lift Speed Control System
35/83
#ANTHONY_GARDINER_TAGLIFTING_201212# FUNCTIONS Lock the doors from the Maintenance Terminal.
2.
Set the load in the car during the test (by default 0, empty car) in Pr 20.27.
3.
Set Pr 20.28 to 1
4.
Make 2 calls from the MT to travel the entire shaft (on up and one down, or the other way round). If a full run is not possible, an emergency manoeuvre can be performed (at lest 4 seconds each run) but measurement precision will be reduced (it is recommended that the manoeuvre be performed half way up the shaft to correct the effect of traction cable weight).
5.
At the end of the second run, the function finalises and returns Pr 20.28 to 0 again and returns results for:
20
12
12
1.
G_
- Efficiency (Pr 20.30): if less than 80%, it is important that the installation be mechanically inspected (guides, guide bars, traction cables, etc.).
FT
IN
- Weight in kg that has to be added to the counterweight (Pr 20.31). If it is negative, remove instead of add. It is recommended that the function is run after doing so to see how it has ended up, especially if the weight entered or added is very large.
LI
This calculation is an estimate, if in doubt the best thing is to place a balanced load in the car and measure consumption on ascent and descent, which should be approximately the same (1A difference).
AG
5.3.7. IMPULSE TO UNWEDGE
_T
The drive programming has been conceived to achieve a soft speed profile and good in car comfort. This programming isn’t ideal for unwedging. This function allows the drive to apply the motor with a maximum possible current impulse to try to unwedge it.
AN
TH
ON
Y_
GA
RD
IN
ER
To activate this function, enter 1 for Pr 19.31. For protection, the function automatically deactivates after 120 seconds, giving a T050 fault, that must be reset.
0466017 - Unidrive SP – Lift Speed Control System
36/83
#ANTHONY_GARDINER_TAGLIFTING_201212# PROBLEM SOLVING
6. PROBLEM SOLVING
12
6.1. PROGRAMMING PROBLEMS
Basic parameters Pr 19.14
PLC status Pr 11.48 TMR 5.7.3 Status
NO
0 (no)
M33 Original
101 ** 0 (no) 2 (run)
M33 Extended
G_
YES NO 111 **
1 (stop) 2 (run)
IN
YES NO M33 Optimized
121 ** YES NO
SERVO 131 **
Gearless Ziehl-Abegg
LI
YES NO
FT
Gearless Leroy-Somer
1 (stop) 2 (run) 1 (stop) 2 (run)
141 ** YES NO
1 (stop) 2 (run)
161 **
AG
M34 YES NO
_T
O-170 / SASSI YES NO
C.L.Vector (V.L.Closed)
ER
M322 1000rpm YES NO YES
1 (stop) 2 (run)
201 ** 1 (stop) 2 (run) 211 ** 1 (stop) 2 (run) 221 ** 1 (stop)
IN
M322 1500rpm
DPL status Pr 17.03 TMR 5.7.4 Status
20
Control Mode Pr 0.48 TMR 5.1 Mode
SMApps.Lite?
Lift type
12
If there are any problems during lift start, first check that the configuration corresponds to the installation type, in accordance with the following table:
Doesn’t exist (NO) 2 (run) Doesn’t exist (NO) 2 (run) Doesn’t exist (NO) 2 (run) Doesn’t exist (NO) 2 (run) Doesn’t exist (NO) 2 (run) Doesn’t exist (NO) 2 (run) Doesn’t exist (NO) 2 (run) Doesn’t exist (NO) 2 (run) Doesn’t exist (NO) 2 (run)
(*) These installations never include a card, but one can be installed to provide additional functions.
RD
(**) This parameter has only existed since April 09. If 0 (it is prior to this date), check: No. Poles Pr 0.42 TMR 5.5.1 Poles
Rated Speed Pr 5.08 TMR 5.5.X rpm nom.
Encoder type Pr 3.38 TMR 5.7.1 Type
12 (6)
191 or 306
SC.Hiper
12 (6)
239 or 383
SC.Hiper
16 (8)
239 or 383
SC.Hiper
Gearless Leroy-Somer
32 (16)
Varies
SC.Endat
Gearless Ziehl-Abegg
20 (10)
Varies
SC.Endat
16 (8)
147
SC.Hiper
4 (2)
1410 – 1500
AB
6 (3)
940 – 1000
AB
4 (2)
1440 – 1500
AB
M33 Original
Y_
M33 Extended
GA
Lift type
Control Mode Pr 0.48 TMR 5.1 Mode
M33 Optimized
ON
SERVO
AN
TH
M34
O-170 / SASSI M322 1000rpm M322 1500rpm
C.L.Vector (V.L.Closed)
Having checked lift type, check programming corresponds to installation load and speed by verifying rated current and rpm in tables 4.2.2 and 4.2.3.
0466017 - Unidrive SP – Lift Speed Control System
37/83
#ANTHONY_GARDINER_TAGLIFTING_201212# PROBLEM SOLVING 6.1.1. Change of Control Mode
Recover the parameters from a SmartCard (see section 3.3). Use a PC and CTSoft to record the corresponding file (ask tech. support) If there is an SM-Apps.Lite card reset to default parameters (5.3.3) can be used.
12
• • •
12
If the control mode does not correspond to that contained in the table, it must be changed. This involves resetting the control mode and programming each parameter one by one. As this operation is very laborious it is easy to commit errors, instead proceed as follows:
6.1.2. Change to basic programming
G_
20
If the parameters on the SmartCard do not correspond to the installation either, request an SMApps.Lite or SmartCard from the factory indicating the type of installation.
If the file programmed on the drive does not correspond to the installation type:
IN
Recover the parameters from a SmartCard (see section 3.3).
If there is an SM-Apps.Lite card reset to default parameters (5.3.3) can be used.
FT
Use CTSoft to record the corresponding file (ask at factory).
Manually program the parameters with the values in section 9.
LI
• • • •
6.1.3. PLC deactivation
Using the Keypad Plus:
Pr 11.47=0
Using the Orona MT:
TMR 5.7.3 Activate = NO
ER
• •
_T
AG
If the PLC is active (Pr 11.48=2 or TMR 5.7.3 Status = Run) and it is to be deactivated (for example because it was an M33 ARCA I, and shouldn’t have one), it can be deactivated as follows:
If the lift is an M33 ARCA I, the PLC will have unconfigured some of the parameters, therefore
RD
6.1.4. PLC activation
).
IN
set: Pr 14.16=2.07, Pr 0.06=175, Pr 4.06=175, and record them (Pr 0.00=1000 +
Using the Keypad Plus:
Pr 11.47=2
Using the Orona MT:
TMR 5.7.3 Activate = YES
Y_
• •
GA
If the lift requires PLC (that is, it isn’t an M33 original, nor does it contain an SM-Apps.Lite card) and the PLC is recorded but stopped (Pr 11.48=1 or TMR 5.7.3 Status=Stop), it can be activated:
AN
TH
ON
Check the value of the following parameters: - Pr 8.24=1.45 - Pr 8.25=1.46 - Pr 8.26=1.47 - Pr 14.16=4.07 Alter the parameters must be recorded (Pr 0.00=1000 +
).
If the PLC has not been dumped (Pr 11.48=0 or TMR 5.7.3 Activate = No), its best to recover it from a SmartCard (Pr 0.00=6004 +
), and then activate as indicated above.
ATTENTION 1. The SM-Apps.Lite card automatically deactivates the PLC because it performs the same functions. To activate, first deactivate the DPL. 2. Never activate the PLC on M33 ‘original’ 0466017 - Unidrive SP – Lift Speed Control System
38/83
#ANTHONY_GARDINER_TAGLIFTING_201212# PROBLEM SOLVING 6.1.5. DPL deactivation
12
The DPL software used by the SM-Apps.Lite card activates automatically when the card is inserted, deactivating the PLC. If the code is functioning correctly, parameter Pr 17.03=run (or TMR 5.7.4 Status=run).
17.13=OFF and Pr 0.00=1070 + (DPL ceases to work) 11.47=2 (to activate the PLC) 8.24=1.45 8.25=1.46 8.26=1.47 14.16=2.07 (M33 original) or Pr 14.16=4.07 (rest of lifts).
-
Record parameters Pr 0.00=1000 +
20
Pr Pr Pr Pr Pr Pr
G_
-
12
If there has been a DPL fault (Pr 17.03=triP or TMR 5.7.4 Status=AV) or the DPL has a problem that cannot be recovered, it can be deactivated and operate with the PLC, as follows:
FT
IN
This allows, for example, the car to be moved to access the drive if it is in the shaft and the SM-Apps.Lite card needs to be replaced. 6.1.6. DPL activation
LI
The DPL software used by the SM-Apps.Lite card activates automatically when the card is inserted, deactivating the PLC.
AG
However, if the code has been manually stopped (as described in the previous point), parameter Pr 17.03=1 (or TMR 5.7.4 Status=stop). To reactivate it: Pr 17.13=ON
-
Pr 0.00=1070 +
-
Record parameters: Pr 0.00=1000 +
_T
-
ER
(the PLC automatically deactivates)
Verify that the PLC has been deactivated (Pr 11.48=1 or TMR 5.7.3 Status=Stop). If not, set Pr 19.14 and Pr 19.15 to the correct value (according to section 9.1) and restart the SM)
RD
6.1.7. DPL faults
IN
Apps.Lite card (Pr 0.00=1070 +
GA
If the SM-Apps.Lite card detects a problem, execution of the DPL software is halted and the lift stops. On the Keypad Plus or TMR 1 the associated drive fault is SL3.Er (?212). To recover it, set Pr 0.00=1070 +
. If the fault persists, disable the DPL and activate the PLC (see 6.1.5).
Y_
If the fault is repetitive, obtain the value for the following parameters and consult the Technical Support Department:
AN
TH
ON
Parameter
Description
Pr 17.02
SM-Apps.Lite card hardware version
Pr 17.04
% of card resources used
Pr 17.50
Type of error
Pr 17.48
Code line where error detected
Pr 20.17
DPL software version
0466017 - Unidrive SP – Lift Speed Control System
39/83
#ANTHONY_GARDINER_TAGLIFTING_201212# PROBLEM SOLVING
6.2. DISPLAYING STATUS VARIABLES
The activation and deactivation of inputs and outputs can be observed in the following menus: Parameter
Rescue Input Brake Output
Speed B1 Speed B2 Speed B3 Load Weight Rescue
12
0 - 100% OFF / ON 0/1 OFF / ON 0/1
Brake
G_
Down
20
OFF / ON 0 / 100% OFF / ON 0 / 100% OFF / ON 0/1 OFF / ON 0/1 OFF / ON 0/1
IN
B1 Speed Level Input B2 Speed Level Input B3 Speed Level Input Loadweights Input
Up
6.2.2. GENERAL STATUS VARIABLES
FT
Descend Input
TMR 3.2 Pr 7.01 TMR 3.2 Pr 7.03 TMR 3.2 Pr 8.04 TMR 3.2 Pr 8.05 TMR 3.2 Pr 8.06 TMR 3.2 Pr 0.25 TMR 3.2 Pr 0.23 TMR 3.2 Pr 0.22
LI
Up Input
Value
AG
Inputs and outputs
12
6.2.1. STATUS OF INPUTS AND OUTPUTS
Parameter
Selected speed level
TMR 3.1 Speed ref. Pr 0.14 TMR 3.1 Real Speed Pr 0.10 TMR 3.1 Output Current Pr 0.11 TMR 3.1 SecureDisable Pr 0.29 TMR 3.1 Torque TMR 3.1 Sign. Torque Pr 0.24 TMR 3.1 Power TMR 3.1 Sign.Power Pr 5.03 TMR 3.1 Tension BUS Pr 0.13 TMR 3.1 Mode Pr 0.48 TMR 3.1 Software Pr 0.50 TMR 3.1 Subsoftware Pr 11.34 TMR 3.1 Enc. Position Pr 3.29
RD
Secure Disable
Y_
DC bus voltage
ON
Mode
Software
Subsoftware
TH
GA
Motor torque
Motor power
Encoder position
IN
Power consumption
Value or unit
ER
Variable
Rotation speed
AN
_T
The following variables can also be viewed on the MT or Keypad Plus:
Vnull, V00, … Vmax 1,2… 8 mm/s rpm tenths of A A OFF/ ON 0/1 0 – 175% pos /neg ±175% W pos /neg kW V
V.L.Closed / SERVO CL Vect / SERVO
Description Indicates the speed level selected, according to B1,B2,B3 decoding described in 4.5 Engine rotation speed measured from encoder. Marks reading of drive output current. Indicates if Secure Disable (also called Baseblock) input is activated Marks the amount of torque required from the motor to move the car. The drive estimates this based on measured current. Measurement of power consumed by motor. If negative indicative of power dissipating in braking resistance. Drive BUS DC voltage. Drive control mode.
-
Drive firmware version
-
Drive firmware sub-version
0 - 65535
0466017 - Unidrive SP – Lift Speed Control System
Encoder position (only if absolute)
40/83
#ANTHONY_GARDINER_TAGLIFTING_201212# PROBLEM SOLVING
6.3. PERMANENT MAGNET SYNCHRONOUS MOTORS
12
For most applications without machine rooms permanent magnet synchronous motors are being used, which work at low speed, allowing gearing to be eliminated. This translates in less machine volume and weight and more comfortable and silent operation.
12
These motors are comprised of a fixed part (stator) with the coils and a mobile part (rotor) with magnets that is joined to the motor pulley. In applying current to the coils, a magnetic field is created that drags the magnets and the rotor with them.
G_
20
However, for the motor to rotate it is necessary that the current (and with it the magnetic field) is created in the same position the magnets are orientated towards. If they loose synchronisation, the motor cannot provide torque and will be dragged by the load (with the drive reporting fault Enc10).
LI
FT
IN
For the motor to start this means: • A drive that has been prepared to control this type of motor must be used. It is not sufficient to apply power direct from the power supply. • The drive needs to use an absolute encoder to be aware of the shaft position at all times, to know where it should apply current to the coils. • Given that the encoder mounts manually, an operation is required (called auto tuning or reference seeking) so that the drive can calculate the encoder mounting position. Reference seeking (auto tuning):
_T
AG
The auto tuning operation allows the drive to calculate the position of the motor magnets with in relation to encoder position 0 (reference). This value is saved in parameter Pr 0.43 (TMR 5.5.2 Angle). This operation is carried out at the factory for all motors.
ER
To avoid this parameter having a different value for each motor, an operation called phasing to 0 is also conducted at the factory, which consists of resetting encoder position 0 to the magnet position. Thereby, any motor phased to 0 can be controlled by a drive with Pr 0.43 (TMR 5.5.2 Angle) set to 0 as long as phases U, V, W are respected.
RD
IN
This phasing to 0 operation has been possible since the M33 optimized entered production, and therefore only the M33 ‘original’, M33 extended (plus those where an encoder or phase sequence has been changed followed by an auto tuning) require reference angle to be other than 0.
GA
Section 5.2.1 describes how to perform an auto tuning. If an SM-Apps.Lite card is present, the position can be phased to 0 after auto tuning, as described in 0.
AN
TH
ON
Y_
ATTENTION: THE FOLLOWING IS FUNDAMENTAL TO GUARANTEE ITS OPERATION: •
Protect the encoder cable, removing it as far as possible from the power cables and avoiding cutting or extending it. If electromagnetic noise penetrates this signal, he motor will have problems.
•
Never dismount the encoder. The encoder is joined to the motor shaft on one side and the machine casing on the other. If either were to move in relation to their fastenings, an auto tuning would be needed to recalculate the angle.
•
Never change phases. Check that phases U,V,W coincide on the drive and the motor and correct if necessary. It is not sufficient to respect the order, U on the drive must coincide with U on the motor, V on the drive with V on the motor… To invert the direction of rotation on the motor, use the functions described in 5, never invert the phase order.
0466017 - Unidrive SP – Lift Speed Control System
41/83
#ANTHONY_GARDINER_TAGLIFTING_201212# PROBLEM SOLVING
6.4. FREQUENT PROBLEMS
12
This section describes some of the most frequent problems and provides advice on how to resolve them. Before referring to this section, it is important to check that the basic drive programming corresponds to the type of installation, as contained in table 6.1.
20
12
It is also very frequent that problems are due to poor apparatus counter weighting or poor mechanical efficiency. If the drive has an SM-Apps.Lite card, an estimate is possible as described in 5.3.6. Otherwise, a half load should be inserted in the car and the current consumption measured (Pr 0.12) in both directions. It should be the same in both directions and less than 70% of the rated value (geared asynchronous motors) or 20% (gearless). Short-circuit on output (OI.AC)
•
FT
LI
ER
•
AG
•
Attempting a static auto tuning (no need to unhook cables): in synchronous motors an angle error could produce this fault (although it is not common). If static auto tuning doesn’t produce a fault, check “Angle problems (synchronous motors)”. If it continues to report an error, continue with this section. Bridge contactors: run motor cables direct to drive, respecting the sequence U,V,W. In so doing a short-circuit in the contactor cable can be ruled out, or even a fault with one of its poles. Eliminate the short-circuit cable-set: in gearless lifts, motor phases are taken to the control panel where a contactor shorts them during the rescue operation. By removing the cable-set this avoids there a problem arising here. Check motor cable-set: measure the resistance between phases and ground with a Multimeter, although the value will vary a lot depending on motor power, it should always exceed 0.3 ohms.
_T
•
IN
G_
The drive reports an OI.AC fault when it detects a current peak in excess of 225% above the motor rated value. As software limits current to 175%, this fault can only occur if there is a short-circuit at the power output (U,V,W) or motor control is lost (normally due to a problem with the encoder in synchronous motors). To attempt to see where the problem resides, we recommend:
IN
If cabling and customisation errors have been ruled out, it is probably a motor coil insulation fault. Check with an insulation meter, and replace the motor if necessary. Overload at output (IT.AC)
AN
TH
ON
•
Rated current: check that Pr 0.46 (TMR 5.5.X Curr.nom) is correctly programmed (according to the tables in 4.2.2 and 4.2.3). Counterweight: ensure that the apparatus is properly counterweighted. If the lift is gearless and has an SM-Apps.Lite card, carry out a test as described in 5.3.6. If not half a load has to be inserted in the car and check that current consumption in both directions is similar (approximately 60% of rated motor current for asynchronous motors and 20% for synchronous). Efficiency: check that installation is mechanically correct: guide alignment, lubrication, traction cabling tensioning, pulleys, gearing, pulley friction brake, etc. Encoder angle (synchronous motors): if the encoder has moved or the angle (Pr 0.43) is poorly set, the motor looses torque. If the error is substantial the drive reports other faults (motor looses control), but if it is small this fault can be produced (the drive is capable of controlling the motor but having lost torque requires more current).
Y_
•
GA
RD
To avoid the motor overheating, the drive reports an IT.AC fault if the output current exceeds the rated value (Pr 0.46) during a certain period (which is shorter the greater the current). This section describes what to look at if the motor starts to move (if it doesn’t, consult the previous point) but this fault appears after a period of time.
• •
0466017 - Unidrive SP – Lift Speed Control System
42/83
#ANTHONY_GARDINER_TAGLIFTING_201212# PROBLEM SOLVING The motor doesn’t move The motor doesn’t rotate or starts moving and stops shortly thereafter. Some errors can be produced such as IT.AC. Check in the following order:
12
AG
RD
•
IN
ER
•
_T
•
LI
FT
•
IN
•
G_
20
• •
Control signal activation: check that SecureDisable, Ascend/Descend, speed level signals are correctly activated (see 6.2.1). In M33 original ARCA I lifts, if the speed levels do not activate, the brake micro switches may be faulty. That the drive is not disabled: ensure Pr 6.15=1. That torque is not limited: - M33 original: torque limits (Pr 4.05, Pr 4.06 and Pr 0.06) should be set to 175%. Also check that Pr 14.16=2.07 - Rest of lifts: when the lift starts the torque limit (Pr 0.06) should increase from 0 to 175%. If it doesn’t, check that the PLC or DPL are active (see 6.1) and that Pr 0.58=175. If no SM-Apps.Lite card, check that Pr 14.16=4.07. Check output cabling: check that the 3 phases (U,V,W) arrive at the motor correctly. Perform a static auto tuning (if it produces an RS fault then one or more phases are probably not arriving, fix cabling). If it is a permanent magnet motor, perform checks in section on “Angle problems (synchronous motors)”. That brake output activates: the brake should activate (see 6.2.1) in accordance with the normal operating sequence. With asynchronous motors, if it does not activate check that current (Pr 0.12 or TMR 3.1) increases above half rated (if it doesn’t there may be a problem with the motor output cabling). That the brake opens electronically: use a Multimeter to check that voltage reaches the coils (Attention: on m33 ‘original’, m33 extended and Leroy-Somer lifts voltage measurements using a Multimeter will give strange readings, although it will be possible to see if there is some voltage). Another way of checking it is to see if the brake-micro switch status changes (if present). If they don’t open, check cabling, coils and brake disk. That the brake disk or machine have not seized up: attempt to perform rotary auto tuning (not necessary to remove cables), if it reports a tune1 fault (which means that the shaft cannot rotate during the auto tuning) this is probably the problem. This may be due to the brake having become stuck (has occurred in some M33 optimized where the machine has been exposed to a very damp environment) or to excessive wear in gears, bearings, etc. Consult Authorised Technical Support. That the encoder reads the speed: check that when the shaft moves, that the encoder measures the speed (Pr 3.27 and Pr 0.10). If either does not see speed, check menu 3, encoder cabling and assembly. On synchronous motors RFC mode can be activated (see section 4.12) to operate provisionally without encoder and see if there problem lies there.
12
•
GA
Load overwhelms motor (synchronous magnet motors):
Y_
If on opening the brake, the car is always dragged by the counterweight, the motor is not providing sufficient torque. It will probably be accompanied by fault Enc10, IT.AC.
ON
It is recommended trying in each direction and mid-shaft, leaving a few seconds to make sure there are no loadweight adjustment problems or that the direction of rotation is inverted. Check in the following order:
AN
TH
• •
• •
That the drive is not disabled: ensure parameter Pr 6.15=1. That torque is not limited: - M33 original: current limits (Pr 4.05, Pr 4.06 and Pr 0.06) should be set to 175%. Check that Pr 14.16=2.07 - Rest of lifts: when the lift starts the current limit (Pr 0.06) should increase from 0 to 175%. If it doesn’t, check that the PLC or DPL are active (see 6.1) and that Pr 0.58=175. If no SM-Apps.Lite card, check that Pr 14.16=4.07. That there is power in the motor: can be seen in Pr 0.12 or TMR 3.1 Current. If 0, this means there is an output connection error or the contactor doesn’t go in. That the motor is not feed to 2 phases: check the output cabling, attempt a static auto tuning (if it produces an RS fault then one or more phases are probably loose).
0466017 - Unidrive SP – Lift Speed Control System
43/83
#ANTHONY_GARDINER_TAGLIFTING_201212# PROBLEM SOLVING • •
Ensure counterweight is correct: if the counterweight is very badly constructed, the motor may not have sufficient torque to retain the car. Test inserting more load in the car. Perform checks in section “Angle problems (synchronous motors)”.
12
Load overwhelms motor (asynchronous motors):
•
20
G_
•
That the drive is not disabled: ensure parameter Pr 6.15=1. That torque is not limited: current limit (Pr 0.06) should increase from 0 to 175% when the lift starts. If it doesn’t, check that the PLC or DPL are active (see 6.1) and that Pr 0.58=175. That there is power in the motor: can be seen in Pr 0.12 or TMR 3.1 Current. If 0, this means there is an output connection error or the contactors doesn’t go in. Ensure counterweight is correct: if the counterweight is very badly constructed, the motor may not have sufficient torque to retain the car. Test inserting more load in the car.
IN
• •
12
If on opening the brake, the car is always dragged by the counterweight, the motor is not providing sufficient torque. It will probably be accompanied by fault O.SPd or IT.AC. Check in this order:
Angle problems (synchronous motors) – Fault Enc10
•
IN
•
AG
•
_T
•
Output phases: check that phases U,V,W correctly arrive from the drive to the motor without crossing. Encoder cabling: check encoder cabling for cuts, remove from power cables as far as possible. Encoder angle: check that Pr 0.43 or TMR 5.5.2 Enc.Angle has that correct value (0 in the majority of cases). Encoder mechanical assembly: ensure that the fixed part of the encoder doesn’t slide in relation to the rear machine cover. Recalculate encoder angle: an angle estimate can be produced if the drive has an SMApps.Lite card, if not traction cables will have to be removed and a dynamic auto tuning performed.
ER
•
LI
If the fault is constant (as soon as motor is started), check:
FT
The drive reports an Enc10 fault when it detects that is loosing control over a synchronous motor. This tends to occur when there is a problem with the angle or the encoder.
•
GA
•
Encoder cabling: check encoder cabling for cuts, remove from power cables as far as possible. Encoder mechanical assembly: ensure that the fixed part of the encoder doesn’t slide in relation to the rear machine cover. Program an auto reset: as described further on.
Y_
•
RD
If the fault occurs occasionally, especially during abrupt stops (for example with the inspection operating panel), check:
Counter movement on start
AN
TH
ON
The lift works OK, but there is counter movement on start or it is slightly dragged by the load (if it touches a limit stop it stops). If it shifts or seems to loose control, consult “Load overwhelms motor”. This may be due to the drive not controlling the brake relay (in which case the brake enters and drops with the controller contactors, and therefore when the brake opens there is no current in the motor and the load overwhelms).
If this is happening, it is probably also accompanied by a bump on stop. Check that Pr 0.22 (or TMR 3.2 Brake) change to 0 on arrival at the floor before the controller removes the contactors. If it doesn’t, check Pr 8.21=19.46 (on m33 original, must be Pr 8.21=9.02). If it does, check rtf relay cabling and brake disk.
0466017 - Unidrive SP – Lift Speed Control System
44/83
#ANTHONY_GARDINER_TAGLIFTING_201212# PROBLEM SOLVING It can also be the case that the motor does not have sufficient current when the brake is opened. To discount it, increase Pr 0.51 (TMR 5.4.1 Open brake T) by 500ms and Pr 0.53 (TMR 5.4.1 T start travel) by 0.5s and see if it disappears. Observe if Pr 0.06 reaches 175% before the brake output is activated, if not reduce Pr 0.52 (or TMR 5.4.1 Torque T).
12
If the motor shifts on start but then stops and remains at speed 0 (despite having a speed set point), it is probably at 2 phases (consult “Motor doesn’t move”).
• •
•
20
G_
IN
•
FT
•
Activate the position control (Pr 0.57=1 or TMR 5.4.4 Position Control = YES). If the problem persists, it is not due to the loadweights, consult “Load overwhelms motor”. Check that the loadweight measures correctly. Input (Pr 0.25 or TMR 3.2 Loadweight) should be 0% with car empty and approx. 100% with full load. If it isn’t, loadweights must be configured properly. For Orona loadweights, check that Cancel Weighing = NO in menu 4.3 of the loadweight device. Also check the version (Menu 4.6.1 of Loadweight device), it should 1.0 or later (update if not). For Micelect loadweights, check that internal bridges J1 and J2 are in position 2-3. Check the weight parameters (TMR 3.2 or using the Keypad Plus Pr 0.26, Pr 0.27, Pr 7.10 and Pr 7.13) are those that correspond for the installation. If they are ok, try simply inverting it changing TMR 5.4.4 Sign.Comp. (or, if using the Keypad Plus, invert Pr 7.13 and the sign for Pr 0.26). If there is still counter movement, recalibrate the weight as described in 4.9.2.
LI
•
12
It may be due to the loadweights being poorly configured (in lifts that use them). To verify this:
AG
Bumps on arriving at floor May be due to:
•
_T
GA
•
ER
•
IN
•
Controller disconnecting contactors too soon: extend the contactor drop period (MT Control 5.3.3). The drive stops applying current too soon: extend the contactor drop period and the travel stop time (Pr 0.55 or TMR 5.4.1). The brake drops when the motor hasn’t stopped yet. Increase the brake closing time (Pr 0.23 for m33 original, TMR 5.4.1 or Pr 0.54 for the rest) and contactor drop time. The drive doesn’t control the brake relay (the brake enters and drops with the controller contactors). If this is happening, it is probably also accompanied by a shift on start. Check that Pr 0.22 (or TMR 3.2 Brake) change to 0 on arrival at the floor before the controller removes the contactors. If it doesn’t, check Pr 8.21=19.46 (on m33 original, must be Pr 8.21=9.02). If it does, check rtf relay cabling and brake disk. The car overruns the floor because the motor doesn’t stop in time: check deceleration, jerk and floor approximation speed parameters.
RD
•
Y_
Controller faults 345 and 346
ON
In optimized M33, M34, Nuevo Renova and gearless Leroy-Somer or Ziehl-Abegg lifts the controller reads the status of each brake via the micro switches. The majority of cases only have 2 brakes (MT Control 5.3.4.3 Controller FR = [C_2]) but in Leroy-Somer machines there can be 3 or 4 brakes ([C_3] or [C_4]).
AN
TH
In m33 ‘original’ and extended lifts, there is just one reading and both contacts in series (MT Control 5.3.4.3 Control FR = [C_1]). M33 ARCA I lifts did not read the brake micro switches (although they did cut speed signals, see 0451118). In gearless Leroy-Somer lifts, the contacts are normally closed instead of open, and therefore should be programmed MT Control 5.3.4.3 Logica.Ent.FR = [N_C]. In the rest it should be [N_O].
Micro switch activation and deactivation can be seen in MT Control, 3.5.1 (attention, the logic of inputs E7, E8 and E9 is contrary to that of E6): • •
Input E6: micro 1 (or both micros in series for M33 original and extended) Input E9: micro 2
0466017 - Unidrive SP – Lift Speed Control System
45/83
#ANTHONY_GARDINER_TAGLIFTING_201212# PROBLEM SOLVING • •
Input E7: micro 3 (only in Leroy-Somer machines with 3-4 brakes) Input E8: micro 4 (only in Leroy-Somer machines with 4 brakes)
12
If fault 345 appears, try to move in emergency (which ignores contact status). If the car doesn’t move, the brake probably isn’t opening, consult “The motor doesn’t move”. If the brake does open and the car moves, check that the base plate inputs are activated. If they fail, change the brake micros. If they manage to activate but despite this there are still occasional faults, extend the time T.Ret.FR.
G_
20
12
If fault 346 appears on arriving at the floor, check that the readings are deactivated. If they don’t, check or change the brake micro switches. If they change, but the lift bumps on stop, extend the contactor drop period (MT Control 5.3.3) at 5d and travel stop time (Pr 0.55 or TMR 5.4.1) at 500m. If the bump and/or fault 346 occur occasionally, proceed in the same manner (increasing both times). The motor doesn’t reach the speed it should – Controller slipping faults (804)
IN
If controller slippage faults occur, check if the motor actually reaches the speed it should reach or if there is a detection problem (with the speed limiter encoder).
LI
FT
See motor speed with Keypad Plus (Pr 0.10 in rpm). Can also be seen with TMR 3.1 Real Speed, but in mm/s (calculation made). If it reaches its correct speed according to table 4.5.1, check the detection levels set for the controller (MT Control 5.3.2). Use the speed reading function (MT Control 4.3.3) to see if the encoder reads properly from the speed limiter.
AG
If there are occasional errors, slightly reduce the parameter associated with MT Control 5.3.2: for example, if an optimized M33 every so often gives approximation speed slipping errors, reduce 5.3.2 V0 from 7c to 6c. If the motor doesn’t reach the speed it should, check:
_T
RD
• •
ER
•
Speed parameter programming (according to tables in 4.5). That the drive is reading the reference properly indicated by the control (TMR 3.1 Ref. Speed or Pr 0.14 as indicated in 4.5.1). That the number of poles is correct. Special attention to M322 (4 poles 1500rpm motors and 6 poles 1000rpm motors). Rated speed from rating plate: doesn’t relate to a 1m/s motor for a 1.6m/s installation, etc. That voltage isn’t saturated (synchronous motors): with descending empty car, check that voltage (Pr 5.02 or TMR 3.1 Voltage) does not reach the rated value programmed for Pr 0.44 or TMR 5.5.2 Voltage nom. (which should always be 390). If not, check the counterweight and if it persists consult Technical Support Service.
IN
• •
GA
Also note that the control gives an approximation speed set point when it is beyond end magnets CO and CU. There may be a problem with these magnets or the direction of rotation.
Y_
The lift overruns the travel stop (on all trips)
ON
Check speed, acceleration, deceleration and jerk parameters according to tables in 4.5.1 and 4.5.2. The jerk can be increased for stronger deceleration (although comfort will be reduced, it is preferable to changing acceleration and deceleration).
AN
TH
Check the deceleration distances programmed in MT Control 5.4.3.1 (type II/III positioning) or the placement of speed change screens CS/CB (type I positioning). Increase them if necessary. Check the apparatus counterweight and the state of the braking resistance. The lift overruns the travel stop (occasionally) – 2336 Anomalies The drive overruns the travel stop occasionally, probably due to electromagnetic noise problems in the CAN bus (which tend to produce 2236 control anomalies). • •
Check programming for Pr 2.04 = Fast. Check the cabling layout, attempting to follow the advice in 6.6.
0466017 - Unidrive SP – Lift Speed Control System
46/83
#ANTHONY_GARDINER_TAGLIFTING_201212# PROBLEM SOLVING • •
Place resistances at the control signal inputs to make the more robust vis-à-vis emissions, as indicated in 2.3. Use a Gateway panel to insulate the bus from the power panel (consult with Technical Support Service).
12
12
If the problem occurs at the ends on start, it may be due to poor loadweight reading which provokes a small counter movement and touches the limit stop. Activate position control to see if it disappears. th or thS fault
G_
20
This fault is due to the drive having a poorly programmed digital input (Pr 7.15 is set to th instead of Volt). Given that the default Control Techniques programming is Pr 7.15=th whilst the configuration used by Orona is Pr 7.15=Volt, this fault tends to occur when the drive has been reset to the Control Techniques default parameters (in which case the entire drive will have to be reprogrammed).
IN
It is recommended to check the drive programming according to table 6.1. If the programming is bad, the parameters will have to be recovered from the SmartCard or from SM-Apps.Lite. If the other parameters are ok and just the fault has to be recovered, program Pr 7.15=Volt, press ).
FT
and record parameters (Pr 0.00=1000 +
LI
Some of the parameters on menu 0 have strange values or are not accessible (Keypad Plus)
AG
The parameters in menu 0 are copies of parameters from other menus to make them more easily accessible.
_T
Review the control mode (Pr 0.48). If it is bad, recover parameters from the SmartCard or SMApps.Lite. Check the parameters for menu 11 and 22:
GA
ER
Pr 11.14=4.03 Pr 11.15=7.02 [4.08**] Pr 11.16=4.09 Pr 11.17=7.12 Pr 11.18=3.42 Pr 11.19=8.09 Pr 11.20=11.42 Pr 22.01=11.33 Pr 22.02=11.32 Pr 22.03=18.40 [no**] Pr 22.04=18.45 [11.30**] Pr 22.05=11.24 Pr 22.06=11.25
IN
RD
11.01=3.01 11.02=4.01 11.03=5.05 11.04=1.50 11.05=1.22 11.06=1.23 11.07=1.24 11.08=1.25 11.09=1.28 11.10=18.27 [*] 11.11=18.01 [8.02**] 11.12=8.01 11.13=8.03 [9.09**]
Y_
Pr Pr Pr Pr Pr Pr Pr Pr Pr Pr Pr Pr Pr
Pr Pr Pr Pr Pr Pr Pr Pr Pr Pr Pr Pr Pr Pr
22.07=11.23 22.10=5.12 22.11=5.18 22.18=11.31 22.20=11.29 22.21=19.12 22.22=14.07 22.23=12.47 22.24=12.46 22.25=19.13 22.26=12.48 22.27=19.49 22.28=18.11 22.29=18.12
[no**] [no**] [no**] [no**] [no**] [no**] [no**] [no**] [no**]
ON
(*) This parameter is worth 2.13 on M33 originals and 2.17 on M33 extended or asynchronous motors (M322 and Machine Room)
AN
TH
(**) These parameters had this other value for M33 originals (or didn’t exist). Check that the Keypad Plus firmware version (Pr 40.02) is not 04.04.00, 04.04.01, 04.04.02, 04.04.03. These versions can cause problems when modifying parameters on menu 0: a different parameter is modified from the correct one, for example: -
When modifying Pr 0.17 value Pr 8.26 is modified instead of Pr 1.24
-
When modifying Pr 0.19 value Pr 7.11 is modified instead of Pr 1.28
If you have one of these versions, consult the Technical Support Service. Versions 04.04.04 and later do not exhibit this problem.
0466017 - Unidrive SP – Lift Speed Control System
47/83
#ANTHONY_GARDINER_TAGLIFTING_201212# PROBLEM SOLVING Motor noise and/or vibrations These problems may be caused by the drive control or by mechanical problems with the installation (poor guide alignment, wear, poorly aligned or tensioned traction cables, pulleys jumping, etc.).
M33 original lifts: Pr 14.06=2.07 Rest of lifts without SM-Apps.Lite card: Pr 14.06=4.07 Rest of lifts with SM-Apps.Lite card: Pr 14.06=0
12
• • •
12
Check first that parameter Pr 0.06 does not oscillate during motor operation (should remain constant at 175% as indicated in the graphics for sequence 4.4.1). Check:
20
Also check hat he PLC or DPL are working according to table in 6.1. If necessary, the DPL can be deactivated and it can operate with the PLC to rule out card problems.
G_
If the motor is asynchronous, RFC mode can be activated (see 4.12) to rule out encoder assembly problems.
AG
• • •
FT
•
Asynchronous motor: TMR 5.5.1 Current nom. (Pr 0.46), Poles (Pr 0.42), rpm nom (Pr 5.08), Power fact. (Pr 0.43). Synchronous motor: TMR 5.5.2 Current nom. (Pr 0.46), Poles (Pr 0.42), rpm nom. (Pr 5.08). Encoder: TMR 5.7.1 type (Pr 3.38), lines (Pr 3.34), Tension alim. (Pr 3.36). Speed control: TMR 5.4.2 Gain P. (Pr 0.07), Gain I. (Pr 0.08), enc. filter (Pr 0.28). Current control: TMR 5.6.x Gain.P.curr. (Pr 0.38), Gain.I.curr. (Pr 0.39), Filter curr. (Pr 4.12).
LI
•
IN
Check that the following parameters are programmed as stipulated:
_T
Check that indicated motor parameters coincide with the rating plate, if not make a note of original values and program parameters according to plate. Attempt to perform a static auto tuning (see 5.5.2) to calculate new control gains.
ER
If the problems persist, the control loops can be retouched but be aware that these adjustments are delicate. Lock the doors and always test without anyone in the car and with the stop button within hands reach, because the motor may become unstable and damage the installation.
0ms 0
Test 2
Test 3
Test 4
Test 5
Test 6
Test 7
Test 8
Test 9
0ms 2
1ms 0
1ms 1
1ms 2
2ms 0
2ms 2
4ms 0
4ms 2
GA
Current filter Encoder filter
Test 1
RD
Parameter
IN
Change the current (Pr 4.12 or TMR 5.6.X Curr. Filter) and speed (Pr 0.28 or TMR 5.4.2 Enc. filter) reading filters according to the following table:
If it is still not resolved, return to original setting and try:
ON
•
If the motor makes noise even when empty (no cables), try changing the current control parameters. If oscillations are noted in the car or motor, try changing the speed control parameters.
Y_
•
The best way of evaluating the behaviour of these parameters is to use a PC and the CT-Scope tool to chart:
AN
TH
•
•
•
Motor current (Pr 4.02) against required torque (Pr 4.03). Attempt to adjust current control parameters to avoid oscillations in the chart or excessive noise in the motor. Motor speed (Pr 3.02) against reference speed (Pr 3.01). Having ensured there are no current jumps, the speed loop parameters can be changed to see there are not oscillations in this chart. Attention to the in-car effect of these parameters: good tracking of set point speed does not guarantee good in-car comfort (the oscillation may be due to other parts of the mechanical system).
0466017 - Unidrive SP – Lift Speed Control System
48/83
#ANTHONY_GARDINER_TAGLIFTING_201212# PROBLEM SOLVING There are also tools (e.g. SOINDAR) that allow the oscillations produced in-car to be measured and later analysed to determine what could be the cause of the oscillations. Consult Technical Support Service.
12
Not all parameters visible or units not correct (using the Orona MT) Check the MT version in Menu 2.8.1 MT Functions. Should be 8.0 or above.
12
If communication is via loadweight plate, also check the version in Menu 4.6.1 of the Loadweight device. Should be 1.10 or above.
20
Fault Oht4.P
IN
G_
This fault indicates excess temperature in the input rectifier. Can only occur in size 4 or larger drives. If it were to occur sporadically independent of load, could be a problem with noise in the temperature reading, in which case place 2 330nF 500V condensers in parallel between DC+ and GND (can be requested from Control Techniques, reference 1691-0006-02). Another option is to program an auto-reset (see further on).
FT
If it occurs only under severe traffic conditions, check the counterweight and attempt to reduce the switching frequency (Pr 0.41 or TMR 5.6.X). Cannot modify parameters
AG
LI
Check that parameter Pr 0.49 is at L2. If when attempting to modify a parameter the screen displays CODE, this means that a code has been entered by mistake to block parameter access. To unlock: 1. Turn off the drive.
GA
RD
IN
ER
_T
2. Turn it on whilst pressing the blue button and the down arrow on the joypad.
Y_
3. Make a note of the code that appears for parameter Pr 0.34. 4. When CodE appears on the console, enter the code (Pr 0.34).
ON
5. Lastly, modify parameter Pr 0.49=LOC L2 (Access to all menus). Differential jumps (occasionally)
AN
TH
Check the connections for the ground cables. Check input power cabling. Measure insulation from ground for input power cabling and motor cabling with insulation meter (disconnecting main switch so there is no power). If problems persist, substitute the differential for one with high immunity. Auto reset If the drive presents a sporadic fault which doesn’t appear to prejudice the operation of the device, an auto reset can be programmed (so that you do not always have to recover it).
0466017 - Unidrive SP – Lift Speed Control System
49/83
#ANTHONY_GARDINER_TAGLIFTING_201212# PROBLEM SOLVING To do so, configure parameter Pr 10.34 = 2 (to attempt two fault recoveries) and Pr 10.35 = 5 (5 seconds between retries). If the fault persists after 2 retries, the drive will stop attempting to recover from it and will remain faulty.
12
Problems with the SmartCard using the Orona MT
12
Loadweight board software versions 0.80 and earlier can have problems reading and recording from the SmartCard. It is recommended to update them to the latest version using the MT. Speeds/accelerations/jerks displayed on TMR don’t make sense
20
The TMR converts the values from the drive (rpm) to show them in mm/s (a simpler and more logical unit of measurement to use in a lift).
Synchronous motors: Pr 5.08 (motor rated speed)
-
Asynchronous motors: Pr 0.02 (maximum speed)
IN
-
G_
To do so, it equals the rated speed for the lift installation (data that is recorded in the controller, but can be consulted in TMR 5.5.1 Rated speed) with:
FT
If the values displayed for speeds, accelerations and jerks don’t seem to make sense, use the Keypad Plus to check them, because the parameters actually used by the drive are in rpm.
AN
TH
ON
Y_
GA
RD
IN
ER
_T
AG
LI
Check the version of the Maintenance Terminal (8.0 or later) and loadweight board (1.10 or later), because in previews versions these parameters were in centimeters/second instead of milimeters/second.
0466017 - Unidrive SP – Lift Speed Control System
50/83
#ANTHONY_GARDINER_TAGLIFTING_201212# PROBLEM SOLVING
6.5. DRIVE FAULTS
12
When the drive has a fault, the name appears in the Keypad Plus. If we have TM the name of the last fault can be seen in menu 1 (only the most frequent, the rest are marked as ?XXX, with XXX being the fault code).
12
With the fault name or code, the following table can be used to establish its cause and how to go about trying to resolve it: Possible cause
Possible solutions
cL2
Analogue input 2 is poorly configured
Check Pr 7.11. Can be due to a problem with the Keypad Plus (see Frequent Problems)
Analogue input 3 is poorly configured
Check Pr 7.15.
Programming error
Check that Pr 6.43 = 0
Programming error
Check that Pr 11.35 = 0
199
Two or more parameters attempting to write the same parameter.
Programming Pr 0.00 = 12001 only parameters causing the problem will be visible. Correct them.
EEF
Corrupt memory data
Reset drive to default Control Techniques parameters (Pr 0.00=1233 + ), recover parameters from an SMApps.Lite or SmartCard and record parameters
28 cL3
G_
20
Fault and code
CL.bit
IN
29
ConF.P
FT
35
dESt
Enc1
AG
31 Encoder fault: supply overload
Enc2
_T
189 Encoder fault: cable cut
ER
190
LI
111
Encoder fault: phase fault during movement
Find breaks in encoder cable. Remove as far as possible from power cables. If it persists, change cable and/or encoder.
Enc4
Encoder fault: communication fault
Check Pr 3.36 and encoder cable. Change encoder cable. If it persists, change the encoder.
RD
192 Enc5
Encoder fault: checksum error
GA
193 Enc6
Encoder fault: encoder detects a problem
Enc7
ON
195
Y_
194
Enc8
TH
Enc9
Check encoder cable and replace it. Replace the encoder.
Encoder fault: initialization fault
Check encoder parameters (Pr 3.36, Pr 3.38) and encoder cabling. If it persists, change cable and/or encoder.
Encoder fault: initialization fault on start
Check encoder parameters (Pr 3.36, Pr 3.38) and encoder cabling. If it persists, change the encoder.
Encoder fault: customization fault
Check that Pr 3.26 = 0
Encoder fault: SERVO phase fault
If it occurs during normal operation, encoder angle poorly programmed Pr 0.43. Check U,V,W phase sequence. Perform a rotary auto tuning (no cables) or angle estimate.
196
AN
Check Pr 3.36 and encoder cable. Change encoder cable. If it persists, change the encoder. On asynchronous motors, RFC mode can be activated (see 4.12)
191
IN
Enc3
Check encoder supply voltage (Pr 3.36) and encoder cabling. If asynchronous, switch to RFC (see 4.12) and disconnect encoder.
197
Enc10 198
If it only happens on sudden braking, simply recover the fault by pressing reset. Enc11
Encoder fault: Sin/Cos signal fault
Check encoder cable.
161
0466017 - Unidrive SP – Lift Speed Control System
51/83
#ANTHONY_GARDINER_TAGLIFTING_201212# PROBLEM SOLVING Check encoder parameters (Pr 3.36, Pr 3.38) and encoder cabling. If it persists, change the encoder.
Encoder fault: Endat encoder initialization fault (wrong number of turns)
Check encoder parameters (Pr 3.36, Pr 3.38) and encoder cabling. If it persists, change the encoder.
164
Encoder fault: Endat encoder initialization fault (excessive number of turns)
Check encoder parameters (Pr 3.36, Pr 3.38) and encoder cabling. If it persists, change the encoder.
Enc15
Encoder fault: customization error
Check Pr 5.36=0. If it persists, replace cable and/or encoder.
166
Encoder fault: initialization error (periods/revolution)
Check encoder type (Pr 3.36, Pr 3.38) and encoder cabling. If it persists, change the encoder.
Enc17
Encoder fault: supply overload
Check encoder supply voltage (Pr 3.36) and encoder cabling. If it persists, replace it
Error in executing encoder data recovery function
Reset the fault and program the data manually.
176 Et
Fault activated from digital input
Program Pr 0.00 = 12001, find what parameter has a value of 10.32 and program to its correct value.
HF01-13
Hardware fault
Replace the drive
HF26
Hardware fault
Check braking resistance connection. If it persists, replace the drive.
Hardware fault
Replace the drive
Enc13 163 Enc14
20
Enc16
12
165
G_
167 ENP.Er
FT
6
LI
226 HF17 - 32
AG
217 – 232 It.AC
Overload at motor output
Consult section on Frequent Problems (6.4)
20 Braking resistor overload.
_T
It.Br 19
Programming error
ER
L.SYnC 39
Excess temperature of control plate
IN
O.CtL 23
O.ht2 ó Oht2.P 22 or 105 27
ON
Oht4.P
Check that control mode (Pr 0.48) is not REGEN. Recover default parameters (using the SM-Apps.Lite or Smartcard). Check that fans work and that ambient temperature is not excessive. Reduce switching frequency (TMR 5.6.X or Pr 0.41) Check lift counterweight. Reduce switching frequency (TMR 5.6.X or Pr 0.41)
Radiator excess temperature
Check that fans work and that ambient temperature is not excessive. Reduce switching frequency (TMR 5.6.X or Pr 0.41)
Drive excess temperature (in thermal model simulation)
Check that fans work and that ambient temperature is not excessive. Reduce switching frequency (TMR 5.6.X or Pr 0.41)
Rectifier excess temperature
Consult section on Frequent Problems (6.4)
Output short-circuit
Consult section on Frequent Problems (6.4)
Braking resistance short-circuit
Check braking resistance cabling. Check ohms value for resistance with Multimeter. Measure ground insulation for resistance terminals.
Short-circuit in IGBTs
Measure insulation of output and motor cables.
Overload or short-circuit of 24V power supply.
Check control terminal cabling. If ARCA, disconnect RAA and RTF relays to see if it disappears. For M33 opt, check cable-sets JM1 and JM2, above all that JM2-6 (rtf) is not crossed with JM2-(0V).
Y_
O.ht3
Check apparatus counterweight. If it is correct, increase Pr 10.30 (TMR 5.7.2 T.Resist.Frein)
Power state excess temperature (in thermal model simulation)
RD
21
GA
O.ht1
12
Encoder fault: encoder Hyperface initialization fault
162
IN
Enc12
102
AN
TH
OI.AC o OIAC.P 3 or 104 OI.br o OIbr.P 4 or 103 OIdC.P 109 O.Ld1 26
0466017 - Unidrive SP – Lift Speed Control System
52/83
#ANTHONY_GARDINER_TAGLIFTING_201212# PROBLEM SOLVING O.SPd
Excess speed
The speed reading exceeds Pr 0.02 by 120%. If it occurs during travel, check the programming of this parameter. If the speed has not reached this value, check encoder mechanical assembly.
7
OV o OV.P
Excess voltage in DC Bus
12
If produced because the load overwhelms the motor, consult the section on Frequent Problems (6.4). Check braking resistance cabling and ohms (with the Multimeter).
2 or 106
12
Check counterweight and deceleration (Pr 0.04). Check input voltage (L1,L2,L3). Check motor insulation. Programming error
Check Pr 1.14=Pr so that drive controlled from digital signals.
Input voltage imbalance
Check input voltage (L1,L2,L3), when car moves downwards. Check input cabling.
20
PAd PH o PH.P
G_
34 32 or 107
Program Pr 6.47=1. If it persists, activate auto reset. If additional cards inserted, remove them and attempt to recover faults. If they recover, replace card with new one. If not, replace the drive.
10V output cabling error (terminal 4)
Check that no cable connected to terminal 4.
Excessive consumption internal 24V supply
Check digital input/output cabling.
There has been a power cut whilst recording parameters
Simply warns that the changed parameters may have not been correctly saved. Recover it, check parameters and save again.
IN
Error in internal power source
5 or 108 PS.10V
FT
PS o PS.P
PS.24V
LI
8
SAVE.Er o PSAVE.Er
AG
9
36 or 37 485 communication error
30 th o thS
Digital input configuration error
ER
24 or 25
_T
SCL
Unid.P
Internal drive connection error
IN
110 UV
DC bus voltage below 350V (because L1,L2,L3 input below 250Vac).
GA
RD
1
485 communication fault. Check RJ-45 cable. Replace Keypad Plus. Consult section on Frequent Problems (6.4) Replace the drive Tends to occur whenever voltage removed. If it occurs during normal operation, check L1,L2,L3 input voltage with empty car descending (should be 380-415Vac). If it occurs during a rescue, check the status of the automatic VR. Ensure CEM contactor activates. Check SAI cabling and 220/380 transformer.
The following errors can only occur during auto tuning: Cause
Possible solutions
tunE 18
Auto tuning manually stopped before finishing
Control has probably disconnected the contactors, removing Secure Disable signal. Recover fault and repeat auto tuning.
Auto tuning fails because speed not read from encoder.
Can be due to an encoder fault or shaft hasn’t rotated (because cables not removed or brake not opened).
12
Auto tuning fails because motor rotation does not correspond to encoder rotation.
Check U,V,W sequence. If its OK and the fault persists, exchange 2 phases.
tunE3
Encoder signals fail
Check encoder cabling. Replace cable and/or encoder.
Incorrectly configured encoder
Check encoder parameters. If it persists, change cable and/or encoder.
Rotation speed doesn’t coincide with theoretical.
Check number of poles and encoder parameters.
ON
Y_
Fault and code
AN
TH
tunE1 11
tunE2
13 tunE4,5,6 14, 15, 16 tunE7 17
0466017 - Unidrive SP – Lift Speed Control System
53/83
#ANTHONY_GARDINER_TAGLIFTING_201212# PROBLEM SOLVING rS
Stator resistance too great (or circuit open)
33
Should only occur if one or more drive output phases not reaching motor. Check contactor cabling.
Fault and code
12
SmartCard usage errors: Possible solutions
C.Acc 185
Cannot read/write to SmartCard
Check SmartCard correctly inserted. Replace SmartCard
C.boot
Incorrect parameter form writing attempt
Never program Pr 11.42 = 3 (auto) or 4 (boot)
178
Cannot access SmartCard because it is being accessed from another location.
Repeat the operation. If it persists, disconnect additional cards, and retry.
C.Chg
The SmartCard is not empty
Repeat deletion operation (Pr 0.00=9999 +
SmartCard data doesn’t coincide with parameters
Recover by pressing
SmartCard doesn’t contain the data that is being attempted to be recovered
Insert SmartCard with data
183 C.Err
SmartCard data is corrupt
Check SmartCard correctly inserted.
G_
C.bUSY
20
177
C.dAt
FT
188
)
IN
179 C.Cpr
12
Possible cause
Replace SmartCard
C.Full
LI
182 The SmartCard is full.
Use another SmartCard
180
SmartCard data corresponds to different optional cards.
C.Prod
SmartCard data is not compatible
175 SmartCard data is write protected
ER
C.Rdo
_T
C.Optn
AG
184
181 C.rtg
SmartCard data is not compatible
IN
186 C.TyP
SmartCard data is not compatible
Delete the SmartCard ( Pr 0.00 = 9999 +
)
Replace SmartCard Remove protection ( Pr 0.00 = 9777 + Delete the SmartCard ( Pr 0.00 = 9999 +
) )
Replace SmartCard Delete the SmartCard ( Pr 0.00 = 9999 +
)
Replace SmartCard
RD
187
Recover faults and check parameters for menu 17.
GA
PLC errors
Possible cause
Possible solutions
UP ACC
Access fault on recording PLC
PLC could not be recorded because drive was enabled. Put the lift in emergency mode and retry.
The PLC tries to divide by 0
Should never occur. Recover PLC from a SmartCard
The PLC takes up too much space in memory
Should never occur. Recover PLC from a SmartCard
The PLC attempts to write a value above the max. for a parameter
Should never occur. Recover PLC from a SmartCard
PLC attempts to write to non-existent parameter
Recover parameters and PLC from a SmartCard.
PLC attempts to write to read only parameter
Should never occur. Recover PLC from a SmartCard
PLC attempts to read a parameter that is read only
Should never occur. Recover PLC from a SmartCard
98
ON
UP div0
Y_
Fault and code
90
UP OFL
AN
TH
95
UP ovr 94
UP PAr 91 UP ro 92 UP So 93
0466017 - Unidrive SP – Lift Speed Control System
54/83
#ANTHONY_GARDINER_TAGLIFTING_201212# PROBLEM SOLVING UP udF
Indeterminate PLC error
Should never occur. Recover PLC from a SmartCard
PLC program forces the drive to stop.
Should never occur. Recover PLC from a SmartCard
97 UP uSEr 96
Fault and code
12
12
The following errors relate to additional cards, such as the SM-Apps.Lite. The X that appears in the fault code stands for a 1, 2 or 3 depending on the slot where the card is installed. Fault codes also differ depending on the slot. Possible solutions
The SM-Apps card in slot X has detected a fault
Check section 0
Hardware fault for SM-Apps.Lite card in slot X
Check card installation. If it persists, replace it.
The SM-Apps card in slot X has been removed
Informational only. Recover faults and record parameters.
203,208,213 SL.rtd
Internal SM-Apps card error
Reset fault. If it persists, consult Technical Support Service.
The Watchdog for the card in slot X has overflowed
Should not occur (watchdog not used). Check that Pr 17.18=0. Recover fault.
An SM-Apps card has been changed in slot X (one model for another)
Informational only. Recover faults and record parameters.
200,205,210 SLX.nF
201,206,211 SLX.dF
AG
204,209,214
LI
215 SLX.tO
G_
SLX.HF
IN
202,207,212
FT
SLX.Er
20
Possible cause
Possible cause
ER
Fault and code
_T
The following errors are provoked by the DPL code on the SM-Apps.Lite card when it detects a problem with lift operation:
t049
Drive doesn’t have a PLC recorded and is attempting to perform operation 5004 (Record PLC to Smartcard)
If it is an M33 original it doesn’t need a PLC, but other installations should have this program recorded, if this is not the case obtain a Smartcard from the factory.
Time has elapsed for unwedging the device (2 minutes)
If more than 2 minutes are needed to unwedge, when this period has elapsed Pr 19.31 (Activation unwedging mode) should be reset to 1.
IN
49 t050
RD
50 t055
The protection against winding of the ropes has actuated
Increase the protection torque (Pr 19.16) or disable the protection (Pr 19.32=0)
AN
TH
ON
Y_
GA
55
Possible solutions
0466017 - Unidrive SP – Lift Speed Control System
55/83
#ANTHONY_GARDINER_TAGLIFTING_201212# PROBLEM SOLVING
6.6. CABLING ADVICE
12
All electrical equipment emits electromagnetic signals and is susceptible to being affected by electromagnetic radiation. A frequency drive in particular, because of the way it works, is a piece of equipment that can emit electromagnetic radiation affecting other equipment.
20
12
This electromagnetic emission can be transmitted by cables (conducted) or by air (radiated). Cable layout can amplify emission levels, and therefore it is essential that the installation be arranged according to ORONA criteria. It is equally important that the accessories used by the drive are defined in the ORONA product.
G_
6.6.1. ELECTROMAGNETIC EMISSION REDUCTION ELEMENTS
Input filter. Electrically installed prior to the drive and located as close to it as possible. The connection cable between the filter output and the drive input should be as short as possible. Earths should be connected. The filter should not be bridged.
•
Output ferrite. The drive output power cable, prior to the contactors, contains a ferrite around which each of the three power conductors is wound 3 times (2 in the case of the M34).
•
Motor power cable. This is a shielded cable, with good quality shielding (covering > 85%). The shield is fixed to earth at each end, using metallic clasps that fasten most of the shield surface.
•
Motor rescue cable (only synchronous motors). This is a shielded cable, with good quality shielding (covering > 85%). The shield is fixed to earth at each end, using metallic clasps that fasten most of the shield surface. In future this shielded cable may not be so if Steward type 28B1531-000 ferrite is used with three cable turns (or similar characteristics).
•
Braking resistance cable. This cable is also shielded (like the motor power cable) and has similar characteristics. The cable should also be fixed to ground and both ends. Must be as short as possible.
•
Supply cable for brakes with overexcitation. With this equipment, used only on M33 ‘original’, M33 extended y gearless Leroy-Somer machines, the cable has to be shielded and fixed to ground at each end.
•
Motor encoder cable. This cable is shielded and its ground connections are made internally. This cable is today installed along with a Steward (or similar) ferrite 28A2025OA0.
•
Load resistances, drive inputs. 1kOhm resistances are placed on all drive inputs which act as a load and immunize against the coupling of damaging signals in these cables.
Y_
GA
RD
IN
ER
_T
AG
LI
FT
IN
•
ON
6.6.2. CRITERIA FOR CORRECT CABLING
AN
TH
•
Use of shielded metallic cable-sets for all cables with a power noise signal (motor, synchronous motor rescue, over-excited brakes, braking resistance). Connected to shielding at each end.
•
If running in parallel, the noise cables should be separated at least 30 cm from other channels.
•
Assemble sot that conductors or cables that carry different classes of signal cross each other at right angles, particularly in the case of sensitive and noisy signals.
0466017 - Unidrive SP – Lift Speed Control System
56/83
#ANTHONY_GARDINER_TAGLIFTING_201212# PROBLEM SOLVING •
Free or unused conductors in a cable should be systematically connected to ground (chassis, channelling, cabinet, etc. ) at each end.
0461466
•
M33 optimized:
0461432 and 0461437
•
M33 ‘original’ and extended:
0461404
•
Gearless Ziehl-Abegg:
0461459, 0461461 and 0461463
•
Gearless Leroy-Somer:
0461440, 0461442 and 0461444
•
M322:
0461406
•
With machine room:
0461424
20
M34
G_
•
12
12
6.6.3. CABLING LAYOUT DIAGRAMS
FT
IN
Having started the installation, we can make an indirect measurement that tells us if the installation has been correctly performed. We should verify, using the Maintenance Terminal, for the near total absence of error messages in the bus after various car travels.
BRAKING RESISTANCE CABLESET WHAT’S WRONG WITH IT? •
It isn’t shielded.
•
It’s long.
•
The cable is looped (power emission).
•
It runs parallel to the filter cable.
WHAT’S WRONG WITH IT? •
The encoder cable and motor power supply cable run together, they should be separated by at least 300 mm if they run parallel.
•
The cable, on arrival at the panel, forms a long loop before passing through the ferrite. Cables should be a short as possible and not have loops.
AN
TH
ON
Y_
GA
RD
IN
ER
_T
AG
LI
6.6.4. EXAMPLES OF POOR CABLING LAYOUT
0466017 - Unidrive SP – Lift Speed Control System
57/83
#ANTHONY_GARDINER_TAGLIFTING_201212# PROBLEM SOLVING WHAT’S WRONG WITH IT?
20
12
12
This capacitor is incompatible with the external filter. It must be removed.
WHAT’S WRONG WITH IT?
IN
ER
_T
AG
LI
FT
IN
G_
The filter ground cable should be connected to the drive’s ground terminal.
WHY IS THIS OK? Metallic clip fixes shielding to chassis (ground). Covering > 180º.
AN
TH
ON
Y_
GA
RD
6.6.5. EXAMPLES OF GOOD CABLING LAYOUT
0466017 - Unidrive SP – Lift Speed Control System
58/83
#ANTHONY_GARDINER_TAGLIFTING_201212# PROBLEM SOLVING The following image displays an example of how to layout cabling in an M33 Optimized lift, separating power, short-circuits and encoder cables as much as possible: Short resistance connection
LI
FT
IN
G_
20
12
12
Encoder cable-set separated from power cable
AG
_T
Short-circuit cable-set separated from rest of cables Shielding to ground Cables cross 90º
Motor connections separated from rest of cables Shielding to ground Cables cross 90º
ER
6.6.6. ELECTROMAGNETIC COMPATIBILITY REGULATIONS
IN
By following the advice above, the installations should give no problems at all. It has been demonstrated in accredited labs: That, emissions levels from ORONA installations are within the levels set by Standard EN 12015.
•
That, immunity levels from ORONA installations are within the levels set by Standard EN 12016.
GA
RD
•
Y_
Compliance with the standard is an important guarantee. However, there may be installations, where due to their special characteristics there is a problem with: Poor ground connections.
•
Very sensitive radio/audio equipment installed near the lift. There are particularly sensitive radio frequencies.
ON
•
AN
TH
In such cases, special intervention from the Technical Support Service can be sought.
0466017 - Unidrive SP – Lift Speed Control System
59/83
#ANTHONY_GARDINER_TAGLIFTING_201212# INDEX OF ELECTRICAL DIAGRAMS
7. INDEX OF ELECTRICAL DIAGRAMS Lift type
Diagram type
Options
Diagram code
ARCAI
Gearless
M33 original
Power
No rescue
0451117
With rescue
0451129 0451118
M33 original
No rescue
Power
M33 extended
0461011
With rescue
0461016
M33 optimized
No rescue
Power
Ziehl-Abegg
With rescue
IN
Control and series of safeties
G_
Gearless
20
Control and series of safeties ARCA II
FT
Ziehl-Abegg > 22kW
Power
LI
Control and series of safeties Leroy-Somer
No rescue
AG
Control and series of safeties Power
_T
Nuevo Renova Eléctrico
ER
IN
M322
Machine room
Power
O-170 & SASSI
TH
AN
0461052 0461099 0461053 / 61 0461059 / 60 0461053 / 61
With rescue
0461095 / 89 * 0461096 / 90 *
No rescue
0461703
With rescue
0461704 0461707
No rescue
0461017
With rescue
0461018
Control and series of safeties Power
0461051
0461094 / 88 *
Control and series of safeties
ON
Y_
GA
RD
Geared.
Power
0461012
No rescue
Control and series of safeties
M34
12
Machine type
12
Controller type
0461019
No rescue, brake 205V
0461027
With rescue, brake 205V
0461028
No rescue, brake 60V
0461029
With rescue, brake 60V
0461064
No rescue, ecobreak
0461049
With rescue, ecobreak
0461065
Control and series of safeties
0461033 / 34
(*) Lift without/with compensating measures
0466017 - Unidrive SP – Lift Speed Control System
60/83
#ANTHONY_GARDINER_TAGLIFTING_201212# REPLACEMENT PARTS
8. REPLACEMENT PARTS
12
8.1. EQUIPMENT REPLACEMENT
12
Drive programming varies depending on the installation, and therefore if a new drive is installed (requested as a replacement or using a code from another installation) the programming will not correspond to what’s required for that particular installation.
20
8.1.1. Using the SmartCard
IN
If it is an M33 ‘original’ (doesn’t require PLC): Pr x.00=6001 + In all other cases: Using TMR 4.4 Inverter -> SM = YES Using the Keypad Plus: Pr x.00=6004 +
and Pr x.00=6001 +
LI
FT
• •
G_
The simplest way of performing the replacement is to use the SmartCard to copy the programming from the old drive to the new one. Once the new equipment has been installed, insert the SmartCard from the old machine and recover its programming:
AG
If the new drive has an SM-Apps.Lite card, parameter Pr 19.14 and Pr 19.15 should be programmed according to the type of installation (see section 9). After programming these values, the drive and SM-Apps.Lite card must be reset: Pr x.00=1070 +
.
_T
After doing this, the basic equipment configuration must be checked against the table in section 6. Also the value of the following parameters must be checked: If the drive doesn’t have an SM-Apps.Lite card: Pr 8.24=1.45; Pr 8.25=1.46; Pr 8.26=1.47; Pr 14.16=2.07 (M33 originals) or 4.07 (all other lifts).
•
If the drive has an SM-Apps.Lite card: Pr 8.24=0; Pr 8.25=0; Pr 8.26=0; Pr 14.16=2.07 (M33 originals) or 0 (all other lifts).
IN
ER
•
RD
Test for correct lift operation and record parameters. It’s a good idea to record a copy of the new programming (with parameters Pr 19.14 and 19.15) on the SmartCard.
GA
8.1.2. Recovering default parameters
Y_
If the new drive has an SM-Apps.Lite card, an installation's default parameters can be recovered as described in section 5.3.3. When the process is finished, check for correct lift operation and record parameters.
ON
8.2. ADDING AN SM-APPS.LITE CARD
AN
TH
An SM-Apps.Lite card can be added to any drive to enjoy its additional features. To do so, parameters Pr 19.14 and Pr 19.15 must first be programmed with the values for the installation
type (see section 9.1) and the parameters recorded (Pr 0.00 =1000 +
).
Once programmed, switch off the power to the drive, wait approximately one minute and insert the card. When supplying the drive with power it will report a fault (to indicate that a card has been added). Reset the fault and the SM-Apps.Lite card by programming Pr 0.00 =1070 +
.
Having checked that the lift works correctly, record the parameters. It is advisable to record a copy of the new programming (with values for Pr 19.14 and 19.15) on the SmartCard.
0466017 - Unidrive SP – Lift Speed Control System
61/83
#ANTHONY_GARDINER_TAGLIFTING_201212# REPLACEMENT PARTS
8.3. REPLACEMENT CODES
12
16
16
25
RESISTANCE
5123518.01
100 ohm 520W 5118213.01 75 ohm 780W 5118213.02 50 ohm 1040W 5118213.03
24,2
24,2
32
32
37,8
37,8
47,2
47,2
55,2
FT
16,8
LI
16’8
5123518.01
AG
12
SP 2401 5123512 SP2402 5123513 SP 2403 5123514 SP 3401 5123515 SP 3402 5123560 SP 3403 5123561 SP 4401 5123559
RESISTANCE
5123518.02
_T
12
FILTER
ER
0
DRIVE
IN
In =
5123520
5123520
IN
8.3.2. Lifts with machine rooms MOTOR CURRENT (A)
FERRITE
12
SP 2401 5123512 SP 2402 5123513 SP 2403 5123514
12
FILTER
G_
0
DRIVE
20
MOTOR CURRENT (A) In > In =
In =< 0
12
SP 2401 5123512
12
16
SP 2402 5123513
16
24
SP 2403 5123514
24
31
SP 3401 5123515
ON TH
AN
DRIVE
FILTER
5123518
5123519
0466017 - Unidrive SP – Lift Speed Control System
RESISTANCE PR 80ohm 1200W 5118203 PR 50 ohm 2000W 5118202 PR 40 ohm 3000W 5118204 PR 30 ohm 4500W 5118205
FERRITE
5123520
5123521
62/83
#ANTHONY_GARDINER_TAGLIFTING_201212# REPLACEMENT PARTS 8.3.4. M33 original and extended lifts (ARCA II)
12
16,8
SP 2402 5123513
16,8
24,2
SP 2403 5123514
24,2
32
SP 3401 5123515
32
37,8
SP 3402 5123560
37,8
47,2
SP 3403 5123561
5123518.01
51235118.02
5123519
12
12
15,6
15,6
23,6 26,6
26,6
30,3
30,3
37,8
37,8
43,5
YES
SP 2401 5123512 SP 2402 5123513 SP 2403 5123514
YES/NO
GA
23,6
SP 1406 5123607
AG
9
NO
5123520
80 ohm 1200W 5118203
5123518.01
50 ohm 2000W 5118202
5123518.02
SP 2404 5123516
SP3401 5123515 SP3402 5123560
RESISTANCE
5123608
_T
9
FILTER
ER
0
DRIVE
IN
In =
LI
8.3.5. M33 optimized lifts MOTOR CURRENT (A)
80 ohm 1200W 5118203 50 ohm 2000W 5118202 40 ohm 3000W 5118204 30 ohm 4500W 5118205 25 ohm 7000 w 5118207 20 ohm 8000 w 5118208
12
SP 2401 5123512
IN
12
FERRITE
5123521
5123521
FT
0
RESISTANCE
12
FILTER
20
DRIVE
G_
MOTOR CURRENT (A) In > In =
In =