35 0 5MB
0
Inicio Ascensor
Nueva Noriai-go ancha 20
2400 Min. Overhead
Manual de instalación y ajuste
550
2400 Min. Floor Height
Coche
de aterrizaje Torre
2400 Min. Floor Height
Min. Pit Depth
10000 Max. Rise
Rail
Guía Puerta de acero
Inicio Ascensor
No. B- (20) -38-e
Nueva Noriai-go ancha 20 (Modelo No. K08B)
Manual de instalación y ajuste
Página
1 de 119
Último traducido 10 de enero de, de 2002
OTIS CONFIDENCIAL !!
Preparado por el Grupo de construcción, Nippon Otis
Nota: Esta es una traducción preliminar del último borrador de la instalación de la versión original en japonés y manual de ajuste para Nueva Noriai-go ancha 20 (K08B) equipo de ascensores casa. Algunas modificaciones se han hecho hasta el momento para el proyecto de manual preparado inicialmente. La versión original japonesa todavía se está repasando para su finalización.
ÍNDICE Página
1. Descripción de la nueva Noriai-go ancha 20 (K08B) 2
Página 4.4 Instalación de segundo nivel de los carriles de guía
28
1.1 Especificaciones
2
4.5 soportes de montaje en riel
31
1.2 Estructura
3
4.6 Montar los marcos de automóviles
37
1.3 Plan de caja por sólo abertura frontal
4
4.7 Instalar andamiaje temporal
39
1.4 plan de caja de ascensor para las aberturas delanteras y traseras
4,8 segundo de plomada y nivel por encima de los carriles de guía
4
y los marcos de automóviles
41
1.5 Elevación por sólo abertura frontal
5
4.9 Montaje de la polea de arriba e instalar
1.6 Elevación para las aberturas delanteras y traseras
5
temporalmente la cuerda
1.7 Aplicación
5
4.10 alféizar de montaje
46
6
4.11 Montaje en jamba
51
7
4.12 cabecera montaje y puerta de caja
57 61
2. Seguridad
2.1 soldadura Gas / corte
43
2.2 máquina de lijado
8
4.13 Instalación de equipos de hueco de ascensor
2.3 Taladro eléctrico
9
4.14 Terminate cuerdas en bastidor de la cabina
71
4.15 Montar coche y la seguridad de guardia
73
4.16 Instalación de puerta de operador y el coche
78
4.17 cableado del controlador
80
2.4 trabajo Aparejo
10
2.5 cuerdas prohibidos para su uso en el aparejo / izado
11 cortador 2,6 Potencia
12
2,7 polipasto eléctrico de cadena
13
5.1 Ajuste de secuencia diagrama de flujo
2,8 Soldadura por arco
14
medición de la tensión de prueba / fuente de alimentación 5.2
montaje 2.9 Andamio
15
3. Preparación
dieciséis
3.1 Documentación
dieciséis
propietario / comprador / otro contrato
17
4.1 Plum del hueco del ascensor
18
96 97
5.4 Prueba de funcionamiento
98 101 101
5.7 Ajuste de Seguridad
102
5.8 Puertas / ajuste de los componentes relacionados de la puerta-
104
5.9 Learn ejecutar
106
21
ajuste de dispositivo de pesaje de carga de 5.10
110
24
5.11 Referencias
111
4.2 Instalar y alinear primero nivel de los carriles de guía del
4.3 Instalación de la máquina
Aislamiento
comprobación de la instalación / coche 5.6 holgura de funcionamiento
dieciséis
4. Instalación
95
ajuste del interruptor DIP 5.3
dieciséis
3.4 Herramientas necesarias
bastidor / base
94
5.5 Cuerda cheque guardia de tensión / cuerda
3.2 Confirmación de artículos proporcionados por proveedores
5. Ajuste
Copyright © 2015 Nippon Otis Elevator. Todos los derechos reservados.
Inicio Ascensor Nueva Noriai-go ancha 20 (Modelo No. K08B)
Manual de instalación y ajuste OTIS CONFIDENCIAL !!
No. B- (20) -38-e Página
2 de 119
Último traducido 10 de enero de, de 2002
1. Esquema de la “Nueva Noriai-go ancha de 20” (K08B) 1.1 Especificaciones •
Carga nominal
200 kg
•
Capacidad de pasajeros
3 personas
•
velocidad del coche
20 m / m (o 0,33 m / s)
•
Drive tipo de máquina
Tipo de tambor de la máquina instalada en el interior hueco del ascensor
•
Sistema de control
funcionamiento automático simplex
•
Aumento (o viaje)
10 m (máx.)
•
paradas
4 (máx.)
•
Piso a piso de altura
2,400 mm (min.)
•
Fuente de alimentación
monofásico, 200 V para el funcionamiento del ascensor y 100 V para las luces
•
capacidad del motor
2,8 kW
•
Entrada
Frente solamente (estándar) o delantero y trasero (opcional)
•
tipo de puerta
Motorizadas centro 4 del panel de apertura de puertas con el sistema de protección de la puerta haz de luz (constante)
•
tamaño del coche
1,000 mm (anchura) x 1,200 mm (profundidad) x 2,000 mm (altura)
•
tamaño de la abertura clara
800 mm (ancho) x 1,900 mm (altura)
•
tamaño de caja de ascensor (min.)
- única abertura frontal -
1,350 mm (anchura) x 1,375 mm (profundidad)
Vista frontal y trasera aberturas 1,350 mm (anchura) x 1,470 mm (profundidad) para la construcción de acero
1,350 mm (anchura) x 1,490 mm (profundidad) para madera o reforzado
hormigón
construcción
•
altura por encima
2400 mm (min.) A 3,100 mm (máx.)
•
profundidad del foso
550 mm (min.) A 900 mm (máx.)
Copyright © 2015 Nippon Otis Elevator. Todos los derechos reservados.
Inicio Ascensor
No. B- (20) -38-e
Nueva Noriai-go ancha 20 (Modelo No. K08B)
Página
Manual de instalación y ajuste
3 de 119
Último traducido 10 de enero de, de 2002
OTIS CONFIDENCIAL !! 1.2 Estructura
Las poleas generales
2400 Min. Overhead
componentes
Ligero
Ventilador de ventilación
botonera de cabina Panel del coche
2400 Min. Floor Height
piso del coche
Coche
Jamba
de la puerta de aterrizaje
puerta de
4-Panel central de apertura
aterrizaje
Depth
550 Min. Pit
Baranda (estándar)
Torre de acero carril guía
2400 Min. Floor Height
10000 Max. Rise
Puerta del auto
Bastidor de base
Copyright © 2015 Nippon Otis Elevator. Todos los derechos reservados.
Botón salón
Inicio Ascensor Nueva Noriai-go ancha 20 (Modelo No. K08B)
Manual de instalación y ajuste OTIS CONFIDENCIAL !!
Depth
1200 Max. In-car
1375
Min. Distance between Walls
1.3 Plan de caja por sólo abertura frontal
1000 Max. En el coche de anchura
800 Claro Apertura
1350 Min. Distancia entre paredes
Depth
1250 Max. 1490
Min. Distance between Walls
In-car
1.4 plan de caja de ascensor para las aberturas delanteras y traseras
1000 Max. En el coche de anchura
800 Claro Apertura
1350 Min. Distancia entre paredes
Copyright © 2015 Nippon Otis Elevator. Todos los derechos reservados.
No. B- (20) -38-e Página
4 de 119
Último traducido 10 de enero de, de 2002
Inicio Ascensor
No. B- (20) -38-e
Nueva Noriai-go ancha 20 (Modelo No. K08B)
Manual de instalación y ajuste
Último traducido 10 de enero de, de 2002
OTIS CONFIDENCIAL !! 1.5 Elevación por sólo abertura frontal
5 de 119
Página
1.6 Elevación para las aberturas delanteras y traseras
superior
Ultimo piso
desde el piso inferior) intermedio piso Cuerda
del piso planta
Height
1900
Opening
180
Max. Rise 10000 (10 m)
Depth
550 Min. Pit
Parte inferior
Depth
2400 Min. Floor Height
1900
Opening Height
Cuerda
Max. Rise 10000 (10 m)
(desigual
550 Min. Pit
del carril
Height
Piso
2400 Min. Front
Intermedio
Guía Torre de acero
Opening Floor
del carril
Min. Floor Height for (or Bump from) Rear Opening Floor
Guía Torre de acero
Planta baja
2400
Min. Overhead
Coche 2400
Min. Overhead
Coche
Máquina
Máquina
1.7 Aplicación Nueva Noriai-go anchas elevadores 20 (K08B) de casa están diseñados para ser instalados en la residencia privada solamente. Las aplicaciones indicadas a continuación son, por lo tanto, prohibido.
• Una casa residencial unido a una tienda, oficina, etc. (en la que los pasajeros no especificados puede utilizar el ascensor). • residencia privada a la que se desarrolla la actividad (por ejemplo, servicios de guardería para los niños, personas mayores, etc.)
Copyright © 2015 Nippon Otis Elevator. Todos los derechos reservados.
Inicio Ascensor Nueva Noriai-go ancha 20 (Modelo No. K08B)
Manual de instalación y ajuste OTIS CONFIDENCIAL !!
No. B- (20) -38-e Página
6 de 119
Último traducido 10 de enero de, de 2002
2. Seguridad Al instalar Nueva Noriai-go • 20 de ancho ( Modelo No. K08B) equipo, asegúrese de que cumple con los requisitos de seguridad de WWJSSS (norma mundial del empleo Seguridad del sitio) .. Instrucciones de seguridad relativas a la instalación se presentan con claridad para todos los componentes de este manual. Siga las instrucciones que cuando se hace el trabajo de instalación.
Consulte las siguientes instrucciones sobre el trabajo seguro básico durante la instalación del ascensor.
Nota: Todas las instrucciones se basan en los procesos de campo practicadas en Japón.
Copyright © 2015 Nippon Otis Elevator. Todos los derechos reservados.
Inicio Ascensor
No. B- (20) -38-e
Nueva Noriai-go ancha 20 (Modelo No. K08B)
Página
Manual de instalación y ajuste
7 de 119
Último traducido 10 de enero de, de 2002
OTIS CONFIDENCIAL !! 2.1 soldadura Gas / corte 2.1.1 Los operadores deben haber completado el entrenamiento de habilidades en soldadura de gas.
2.1.2 Soapsuds deben ser siempre colocados cerca de un cilindro de gas. 2.1.3 El acetileno medidor debe tener dispositivo de prevención de retorno de llama.
2.1.4 No hay daños en el medidor de acetileno / oxígeno.
2.1.5 Un extintor de fuego o agua para la extinción de incendios debe estar preparado. 2.1.6 utilizar una hoja de protección apropiado (tal como hoja de protección de salpicaduras) cuando se trabaja en la caja de ascensor.
2.1.7 acetileno cilindro / oxígeno debe tener dispositivo de seguridad contra el vuelco.
2.1.8 Un gallo se debe montar en el cilindro de acetileno. 2.1.9 Use lentes o gafas de soldador.
Detonación válvula de prevención
Espuma de jabon s
Fuego
extintor cubo de agua
Lentes de seguridad
Guante de cuero
Copyright © 2015 Nippon Otis Elevator. Todos los derechos reservados.
Inicio Ascensor
No. B- (20) -38-e
Nueva Noriai-go ancha 20 (Modelo No. K08B)
Página
Manual de instalación y ajuste
8 de 119
Último traducido 10 de enero de, de 2002
OTIS CONFIDENCIAL !! 2.2 máquina de lijado
2.2.1 Los operadores deben haber completado una formación especial en la sustitución de la muela o usarlo en el juicio en el momento de la sustitución.
2.2.2. Implementar inspección previa al trabajo.
•
Asegúrese de que no hay daños o grietas en el alambre eléctrico.
•
Asegúrese de que si un enchufe tiene tres clavijas (con exclusión de aislamiento doble) y un terminal de unión (uso GFCI) se conecta un cable eléctrico y un enchufe
•
Asegúrate de que si no suena sonido anormal durante la operación de prueba.
•
Asegúrese de que no hay una rueda rota o su centro de gravedad no se aparta.
•
Asegúrate de que si hay marcadores de conexión para cables de la placa de distribución temporal
2.2.3 Llevar gafas de protección, una máscara de polvo y guantes.
2.2.4 Utilice una rueda adecuada para un propósito específico (no utilizar la muela abrasiva para el corte.)
2.2.5 Asegúrese de que un tapón se saca cuando se coloca una rueda.
2.2.6 Asegúrese de que no hay inflamables o gasolina cerca de la máquina de lijado.
2.2.7 vasos proteger y terminaron paredes.
cuadro de distribución temporal Use GFCI cuando se utiliza la herramienta eléctrica.
marcador de conexión del cable
gafas de protección
enchufe de tres clavijas (con exclusión de doble aislamiento) (No utilice un sistema
Máscara contra el polvo
de puesta a tierra simple.) guante de protección
Copyright © 2015 Nippon Otis Elevator. Todos los derechos reservados.
Inicio Ascensor
No. B- (20) -38-e
Nueva Noriai-go ancha 20 (Modelo No. K08B)
Página
Manual de instalación y ajuste
9 de 119
Último traducido 10 de enero de, de 2002
OTIS CONFIDENCIAL !! 2.3 Taladro eléctrico
2.3.1 Sin estudios necesarios 2.3.2
Implementar inspección previa al trabajo.
•
Asegúrese de que no hay daños o grietas en el alambre eléctrico.
•
Asegúrate de que si tiene un enchufe de tres clavijas (con exclusión de aislamiento doble) y un terminal redonda (uso GFCI) se conecta un cable eléctrico y un enchufe
•
Asegúrate de que si no suena un sonido anormal durante el uso juicio.
•
Asegúrese de que no hay ningún daño en el cuerpo de la broca.
2.3.3 Asegúrese de que un tapón se saca cuando se coloca una rueda. (Es conveniente colocar una manija tirada cerca del enchufe.)
2.3.4 Mantenga un taladro eléctrico con ambas manos cuando lo utiliza.
2.3.5 No deje de usar gafas de protección y guantes. 2.3.6 Asegúrese de fijar firmemente el material a perforar.
Use GFCI cuando se utiliza la herramienta eléctrica.
guante de protección
gafas de protección
marcador de conexión del cable
Con 15mA disyuntor de fuga a tierra
Cuando se coloca un mango
Conecte con una base
mandril
Copyright © 2015 Nippon Otis Elevator. Todos los derechos reservados.
Inicio Ascensor
No. B- (20) -38-e
Nueva Noriai-go ancha 20 (Modelo No. K08B)
Página
Manual de instalación y ajuste
10 de 119
Último traducido 10 de enero de, de 2002
OTIS CONFIDENCIAL !! 2.4 trabajo Aparejo
Se requiere 2.4.1 formación Habilidad para los operadores de manipulación 1t o más y una formación especial para los operadores de manipulación de menos de 1t (este peso no es un peso de cargas, pero una capacidad de carga de un gancho de izar y una máquina de elevación).
2.4.2
2.4.3
Implementar reunión de seguridad antes de la operación.
• •
Asegúrese de informar a todos los operadores de material a ser izada y el lugar de trabajo.
•
Sólo operadores calificados deben trabajar en el aparejo.
•
Asegúrese de que todos los operadores entiende su / su posición, así como el deber.
•
Nunca se pare debajo de la carga suspendida.
Designar a un operador de señalización y que él / ella confirmar el método de señalización con un operador de la grúa.
Inspeccionar cuerdas de alambre para izar (por un administrador de operación o un operador designado por él).
2.4.4 asegurarse de que un seguro opera adecuadamente cuando un cable se colgaba de un gancho.
2.4.5 Asegúrese de que cada operador repite y confirma una señal cada vez que el operador de señalización envía una señal.
2.4.6 Nunca toque una carga hasta que es correctamente equilibrado y estabilizado y operadores de confirmar que la carga y el aparejo es estable. (Cuando se detecta cualquier anomalía, deje de izado y colocar las cargas estables en el suelo.)
2.4.7 no lo permita la entrada en el área de operación, evitando la entrada de la tercera parte.
inspección de la cuerda
barreras de seguridad Gancho
Pestillo
cuerda de izado
balanceo de carga y estabilización Copyright © 2015 Nippon Otis Elevator. Todos los derechos reservados.
Inicio Ascensor Nueva Noriai-go ancha 20 (Modelo No. K08B)
Manual de instalación y ajuste OTIS CONFIDENCIAL !! 2.5 cuerdas prohibidos para su uso en el aparejo / izado 2.5.1 10 por ciento o más de la cuerda se corta en una torcedura
diámetro 2.5.2 de la cuerda se redujo en más de un 7 por ciento del diámetro nominal 2.5.3 Cuerda con una torcedura
2.5.4 a) deformación considerable (mella en hebra, que sobresale de acero de núcleo, la deformación)
b) Considerablemente corroído cuerda 1 giro
Copyright © 2015 Nippon Otis Elevator. Todos los derechos reservados.
No. B- (20) -38-e Página
11 de 119
Último traducido 10 de enero de, de 2002
Inicio Ascensor
No. B- (20) -38-e
Nueva Noriai-go ancha 20 (Modelo No. K08B)
Página
Manual de instalación y ajuste
12 de 119
Último traducido 10 de enero de, de 2002
OTIS CONFIDENCIAL !! cortador 2,6 Potencia
2.6.1 Los operadores deben tener calificaciones para la sustitución de la muela o utilizarla en la prueba y han completado un entrenamiento especial.
2.6.2 Implementar inspección previa al trabajo.
•
Asegúrese de que no hay daños o grietas en el alambre eléctrico.
•
Asegúrate de que si tiene un enchufe de tres clavijas (con exclusión de aislamiento doble) y un terminal redonda (uso GFCI) se conecta un cable eléctrico y un enchufe
•
Asegúrate de que si no suena un sonido anormal durante el uso juicio.
•
Asegúrese de que no hay ningún borde de corte rota o su centro de gravedad no se aparta.
•
Asegúrese de que no hay ningún daño en el cuerpo de la fresa.
•
Asegúrate de que si hay marcadores de conexión de cables en el cuadro de distribución
2.6.3 Use un escudo chispa. 2.6.4 Llevar gafas de protección, una máscara de polvo y guantes.
2.6.5 Asegúrese de reemplazar un filo de corte después de sacar el enchufe.
2.6.6 Asegúrese de que no hay inflamables o gasolina cerca de la cortadora. 2.6.7 Asegúrese de fijar de forma segura el material a un soporte para el corte.
temporal titular
Use GFCI cuando se utiliza la herramienta eléctrica.
cuadro de distribución
marcador de conexión del cable
escudo de chispa escudo de chispa
mano; en cambio, fijarlo en un gafas de protección
No mantenga un material en la
Copyright © 2015 Nippon Otis Elevator. Todos los derechos reservados.
Inicio Ascensor
No. B- (20) -38-e
Nueva Noriai-go ancha 20 (Modelo No. K08B)
Manual de instalación y ajuste
Página
13 de 119
Último traducido 10 de enero de, de 2002
OTIS CONFIDENCIAL !! 2,7 polipasto eléctrico de cadena
2.7.1 Los operadores deben tener calificaciones de máquina de tracción operativo y han completado un entrenamiento especial.
2.7.2 Implementar inspección previa al trabajo.
•
Asegúrese de que no hay ningún daño o grieta en la línea de alimentación y la línea de control remoto.
• •
Asegúrese de que un cable de tierra está conectado.
•
Comprobar si una cadena de eslinga está lubricada y libre de óxido.
•
Compruebe si no hay grietas o deformaciones en la eslinga de cadena.
•
Comprobar si la cadena es recta sin torsión.
•
Compruebe si el bloque de cadena se mueve a la dirección especificada por un controlador remoto.
•
Compruebe si se inserta un muelle entre un gancho y el cuerpo del bloque de cadena.
•
Asegúrese de que no hay ningún daño en el cuerpo del bloque de cadena.
Asegúrese de que unas funciones de congelación correctamente.
2.7.3 Cuelgue un polipasto eléctrico de cadena a un gancho de la honda de forma segura y asegúrese de que un pestillo funciona correctamente.
•
Cuando se utiliza un gancho temporal, colocar 2 o más M12 o M16 anclas, y configurarlo con un ángulo de la eslinga 60 grados o menos.
Pestillo
Gancho
Derecha
Incorrecto
Compruebe el funcionamiento del pestillo adecuadamente
vista ampliada Alfiler
Copyright © 2015 Nippon Otis Elevator. Todos los derechos reservados.
Inicio Ascensor
No. B- (20) -38-e
Nueva Noriai-go ancha 20 (Modelo No. K08B)
Página
Manual de instalación y ajuste
14 de 119
Último traducido 10 de enero de, de 2002
OTIS CONFIDENCIAL !! 2,8 Soldadura por arco 2.8.1 Los operadores deben tener las calificaciones para la soldadura por arco y han completado un entrenamiento especial.
2.8.2 Implementar inspección previa al trabajo.
• Asegúrese de que no hay daños o grietas en el alambre eléctrico. • Asegúrate de que si muchas cargas no se ponen en una toma de corriente eléctrica en el tablero de distribución y un cable de tierra de una máquina de soldar está conectado a la placa de distribución.
• Asegúrese de que no hay daños en el aislamiento de la cubierta del soporte. •
Compruebe si de puesta a tierra se realiza correctamente.
•
Comprobar si un dispositivo automático de tensión de reducción funciona normalmente por el interruptor de inspección para el dispositivo.
•
Compruebe si el vidrio de un protector de cara no está roto.
• Asegúrate de que si hay marcadores de conexión de cables en el cuadro de distribución. 2.8.3 Use una mascarilla, guantes (cuero) y un protector facial. 2.8.4 Coloque un extintor de fuego cerca de campo de la soldadura, y asegurarse de que no hay inflamables en las proximidades.
2.8.5 Cuando se trabaja en el hueco del ascensor, asegúrese de que no hay inflamable en la boca y usar la protección de encendido correspondiente tal como una lámina contra salpicaduras.
2.8.6 Cuando los cables eléctricos tienen que ser puesto en un pasaje, protegerlos con ángulos o colocarlos en el techo. Cuadro de distribución
Comprobación del interruptor de voltaje automático de reducción dispositivo
Maquina de soldar
Máscara contra el polvo
Careta
Conexión de cable marcador
la protección de cables eléctricos
Guante de cuero
Extintor de incendios
abrazadera de la tierra
Poseedor
Copyright © 2015 Nippon Otis Elevator. Todos los derechos reservados.
Inicio Ascensor
No. B- (20) -38-e
Nueva Noriai-go ancha 20 (Modelo No. K08B)
Página
Manual de instalación y ajuste
15 de 119
Último traducido 10 de enero de, de 2002
OTIS CONFIDENCIAL !! montaje 2.9 Andamio 2.9.1 Los operadores deben haber completado un entrenamiento especial para el montaje y la certificación obtenida.
2.9.2 Tubos de acero para marcos de andamio deberán cumplir la normativa de código.
2.9.3 Capacidad de carga por tramo de la trama de andamio es como sigue:
•
Marco simple. . . . . . . . 250 kg o menos
•
marco estándar. . . . . . 400 kg o menos
2.9.4 Usar una placa de base sólida sin grieta o la corrosión. 2.9.5 Ajuste jacks de la toma de base de modo que cada zanco lleva la misma carga, y montar los tirantes a la cubierta firmemente.
2.9.6 Cuando la construcción de andamios, inserte una articulación en polos del marco, y fijar los bastidores superior / inferior con un acoplador.
2.9,7 Asegúrese de que un pestillo de una pinza para el tablón está bloqueado.
2.9.8 Siempre que extraiga una diagonal vertical de forma temporal, asegúrese de poner de nuevo donde está. 2.9.9 asegurar un arnés de protección contra caídas y usar un arnés de cuerpo completo durante andamios de construcción.
Barandilla
insertado en polos
Acoplador
Tablón
marco de la placa de base
Apuntalamiento jack con el
placa base Conjunto diagonal vertical
Copyright © 2015 Nippon Otis Elevator. Todos los derechos reservados.
Inicio Ascensor Nueva Noriai-go ancha 20 (Modelo No. K08B)
Manual de instalación y ajuste OTIS CONFIDENCIAL !!
No. B- (20) -38-e Página
de 119 dieciséis
Último traducido 10 de enero de, de 2002
3. Preparación En primer lugar comprobar y confirmar el ascensor materiales han de ser entregadas al sitio de trabajo como estaba previsto. A continuación, observar el progreso sitio de trabajo y las condiciones de caja de ascensor para una instalación sin problemas.
3.1 Documentación Tan pronto como reciba la notificación para comenzar los trabajos de instalación en un contrato, se le solicita que primero comprobar y confirmar la fecha de entrega de los materiales de ascensor como se mencionó anteriormente. A continuación, asegúrese de que la siguiente documentación del contrato está disponible antes de comenzar la instalación:
•
Contrato dibujo diseño
•
DQO (Contrato Datos de pedido)
•
diagrama de cableado del controlador Contrato
•
diagrama de cableado de campo contrato
• •
Contrato tabla de progreso Las copias de la forma de sitio de trabajo actas de las reuniones
3.2 Confirmación de los elementos proporcionados por otros proveedores de contratos propietario / comprador / Antes de comenzar la instalación, asegúrese de comprobar las condiciones del lugar para asegurar los elementos indicados a continuación se proporcionan como se muestra en el dibujo trazado contrato y la DQO.
•
Completado la construcción de edificios incluyendo el hueco del ascensor, hoyo, entradas, etc., así como acceso a la máquina.
•
Potencia / utilidades para el funcionamiento del ascensor y las luces (así como de teléfono si es necesario) Si cualquier artículo (s) no se ha
proporcionado totalmente, pida al administrador del sitio de construcción para completar la (s) y confirmar con él / ella su (s) finalización fechas).
3.3 Comprobaciones antes de que comience la instalación Antes de comenzar los trabajos de instalación, compruebe los siguientes elementos con mucho cuidado:
•
Dimensiones de caja reales para ninguna desviación de las tolerancias en el plano de disposición del contrato.
• •
Levantamiento de gancho / haz listo para su uso.
•
Guía vigas carril de soporte se encuentran al principio del hueco del ascensor y en cada rellano.
•
El espacio disponible para el almacenamiento de existencias de material.
alimentación correcta alimentación disponible para el funcionamiento del ascensor y las luces.
3.4 Herramientas necesarias (Para ser añadido más tarde)
Copyright © 2015 Nippon Otis Elevator. Todos los derechos reservados.
Inicio Ascensor
No. B- (20) -38-e
Nueva Noriai-go ancha 20 (Modelo No. K08B)
Manual de instalación y ajuste
Página
17 de 119
Último traducido 10 de enero de, de 2002
OTIS CONFIDENCIAL !! 4. Instalación Instalación secuencia diagrama de flujo Tras el proceso de instalación a continuación, lleve a cabo los trabajos de instalación de forma segura.
1.
Sondear el hueco del ascensor
2.
Instalar y alinear primero nivel de los carriles de guía del bastidor / base
11. Montaje en jamba
3.
instalar la máquina
4.
Instalar segundo nivel de los carriles de guía
cabecera 12. Monte y puerta de caja
13.
Instalar equipos de hueco de ascensor
5. soporte de montaje del carril
14. Terminar cuerdas en bastidor de la cabina
6. Montar los marcos de automóviles
7.
Instalar andamiaje temporal
8.
Tercero a plomo y los niveles superiores de los carriles de guía y los marcos de automóviles
9. Monte la polea superior y colocar
15. Montar coche y la seguridad de guardia
dieciséis.Instalar la puerta del operador y el coche
17. Controlador de cableado
18.
Instalar operador, puerta del coche y materiales de cableado
temporalmente la cuerda
10. alféizar de montaje
19. Instalación de paletas sensor
Copyright © 2015 Nippon Otis Elevator. Todos los derechos reservados.
Inicio Ascensor Nueva Noriai-go ancha 20 (Modelo No. K08B)
Manual de instalación y ajuste OTIS CONFIDENCIAL !!
No. B- (20) -38-e Página
18 de 119
Último traducido 10 de enero de, de 2002
4.1 plomada del hueco del ascensor
Sondear el hueco del ascensor para determinar si es o no el hueco del ascensor tendrá en cuenta el ascensor en las tres dimensiones y decidir dónde instalar los carriles de guía. Coloque la tubería establecido en la viga del piso superior y establecer la ubicación de los centros de carril de guía, sobre la base de la línea de plomada.
4.1.1 Apuntes para las dimensiones
Posiciones de umbral, el carril de guía y la base de marco
(Distancia entre el ferrocarril y
250 mm
umbral)
(Distancia entre bastidor de base y el alféizar) 240
mm
Copyright © 2015 Nippon Otis Elevator. Todos los derechos reservados.
Inicio Ascensor Nueva Noriai-go ancha 20 (Modelo No. K08B)
Manual de instalación y ajuste OTIS CONFIDENCIAL !!
Guía dimensiones ferroviarios
dimensiones DBG
Copyright © 2015 Nippon Otis Elevator. Todos los derechos reservados.
No. B- (20) -38-e Página
19 de 119
Último traducido 10 de enero de, de 2002
Inicio Ascensor
No. B- (20) -38-e
Nueva Noriai-go ancha 20 (Modelo No. K08B)
Página
Manual de instalación y ajuste
20 de 119
Último traducido 10 de enero de, de 2002
OTIS CONFIDENCIAL !!
Dimensiones para el montaje de la puerta (4-panel de la puerta de apertura central para frente solamente la apertura en casa de la construcción de acero)
de pared a pared de caja de ascensor ancho
1350 mm
mm
Taxi
75 mm
Coche fuera de la profundidad
1285 mm
75 mm
Dimensión entre el exterior superficies de los carriles de guía
1200 mm profundidad wallto-pared de caja
1295 mm
1375 mm
Dimensión entre el interior superficies de los carriles de guía
1190.8 mm
250 mm
30 mm
145 mm 50
Umbral
45 mm
45 mm
30mm compensar
30mm compensar
anchura del marco de entrada
1260 mm
Copyright © 2015 Nippon Otis Elevator. Todos los derechos reservados.
Inicio Ascensor Nueva Noriai-go ancha 20 (Modelo No. K08B)
Manual de instalación y ajuste OTIS CONFIDENCIAL !! 4.2 Instalar y alinear primero nivel de los carriles de guía del bastidor / base 4.2.1 Instalar 1er nivel de los carriles de guía Instalar primero el nivel de los carriles de guía en la base inferior y alinearlos. croquis de diseño ferroviario es incluido en
material que se envía desde la fábrica.
1) Verificar dimensiones del bastidor de base que ya está montado en la fábrica. 2) Instalar primero nivel de los carriles de guía (2100 mm de largo sin la longitud de la placa de pescado) al bastidor de base.
fijar temporalmente con (12) la tuerca M12, la arandela plana (12) M12 y (12) S arandela.
3) Aplomado y seguro los rieles.
•
la precisión de fontanería:
Ubicar la tubería fija 1.700 mm o más, aparte de la planta y la asignación debe estar • 0,5 mm con 50 mm de distancia entre plomada y el suelo. 4. Instalación de calibre fontanería riel a la parte superior de los carriles.
5. Asegúrese de que la dimensión de DBG (1,188 mm) en el extremo inferior de los carriles.
Copyright © 2015 Nippon Otis Elevator. Todos los derechos reservados.
No. B- (20) -38-e Página
21 de 119
Último traducido 10 de enero de, de 2002
Inicio Ascensor Nueva Noriai-go ancha 20 (Modelo No. K08B)
Manual de instalación y ajuste OTIS CONFIDENCIAL !!
No. B- (20) -38-e Página
22 de 119
Último traducido 10 de enero de, de 2002
4.2.2 Instalar carril DBG ajuste de ángulo / tampón
4.2.3 Localizar bastidor de base
Para y la dirección fro 1) Temporalmente localizar bastidor de base en una forma para encajar en las dimensiones especificadas.
•
Medir las dimensiones en el extremo inferior de los carriles.
2) marcar la posición del bastidor de base en el suelo del foso como la base en el lado a otro dirección.
3) Cuando hay 2 mm o más tolerancia en cada 1,000 mm de longitud, poner una cuña para nivelar el bastidor de base.
Izquierda a derecha 1) Temporalmente localizar bastidor base en una posición en la distancia entre el carril y la viga lateral es igual. 2) Asegúrese de que la marca en la dirección de un lado a otro está en la posición de la estructura de base, y poner una marca en la dirección de izquierda a derecha.
Copyright © 2015 Nippon Otis Elevator. Todos los derechos reservados.
Inicio Ascensor
No. B- (20) -38-e
Nueva Noriai-go ancha 20 (Modelo No. K08B)
Página
Manual de instalación y ajuste
Último traducido 10 de enero de, de 2002
OTIS CONFIDENCIAL !! 4.2.4 Fix bastidor base de anclaje
•
Fijar el ancla con el fin de evitar la estructura de base de estar en la posición incorrecta.
•
Utilice los pernos de anclaje M12 (5).
(Posición del travesaño de la y el marco de base)
Bastidor de base
Carril
Nota: Asegúrese de mantener la apertura de 10 mm entre el marco de base y carril (250 a 240)
Copyright © 2015 Nippon Otis Elevator. Todos los derechos reservados.
23 de 119
Inicio Ascensor Nueva Noriai-go ancha 20 (Modelo No. K08B)
Manual de instalación y ajuste OTIS CONFIDENCIAL !!
4.3 Instalación de la máquina
Instalar la máquina en el bastidor base. 4.3.1 Montaje del soporte para evitar la cuerda se salga. Montar el soporte antes de la instalación de la máquina, ya que es imposible montar después.
Copyright © 2015 Nippon Otis Elevator. Todos los derechos reservados.
No. B- (20) -38-e Página
24 de 119
Último traducido 10 de enero de, de 2002
Inicio Ascensor Nueva Noriai-go ancha 20 (Modelo No. K08B)
Manual de instalación y ajuste OTIS CONFIDENCIAL !!
4.3.2 Instalación de la máquina
1) Entregar la máquina a la planta baja. 2) Monte • 10 mm grillete (2) y • 10 mm / 2 m cuerda larga cabestrillo (1) para pernos de anilla (2) de engranaje de la máquina
caso. 3) Cuando izar una máquina con el torno, montar sobre 5 m de longitud de la cuerda a la máquina para la estabilización. 4) Montar un caucho para una parte inferior de la máquina a bastidor de base. 5) máquina Set en los pernos de soldadura del bastidor de base.
6) Instalar la máquina y montar una goma para parte superior de la máquina a bastidor de base.
7) máquina Fix con la tuerca M20 (8), llave de tubo y el zócalo. 8) Fijar con pasador de aletas.
Copyright © 2015 Nippon Otis Elevator. Todos los derechos reservados.
No. B- (20) -38-e Página
25 de 119
Último traducido 10 de enero de, de 2002
Inicio Ascensor Nueva Noriai-go ancha 20 (Modelo No. K08B)
Manual de instalación y ajuste OTIS CONFIDENCIAL !! Nota: Tenga cuidado de que el “número de cauchos” y su “dureza” son diferentes entre el lado delantero
y el lado trasero. •
Frente (lado de entrada):
3 para más baja y 1 para una parte superior de la máquina
•
Posterior:
1 para inferior y 3 para una parte superior de la máquina
Nota: 1) la tuerca de montaje M20 (2) y la tuerca M12 (lado del carril) con 1/2 de vuelta.
2) Monte la tuerca M12 (lado del motor) con 3/4 de vuelta. 3) Monte único ángulo de guardia de la cuerda antes de la instalación de la máquina.
4) Remove gear unit and eyebolt of motor after machine installation.
Copyright © 2015 Nippon Otis Elevator. Todos los derechos reservados.
No. B- (20) -38-e Página
26 de 119
Último traducido 10 de enero de, de 2002
Home Elevator
No. B-(20)-38-e
New Noriai-go Wide 20 (Model No. K08B) Installation and Adjustment Manual
Page
Last translated January 10, 2002
OTIS CONFIDENTIAL !! •
How to mount rubber for lower part of machine • Be careful about direction and hardness.
Hardness
Hardness 50
70 M20
•
M20
Hardness
Hardness
50 M12
70 M12
How to Mount Rubber for Upper Part of Machine. • Be careful about direction and hardness.
Hardness 70 M20
27 of 119
Hardness 50
Hardness 50 M12
Copyright© 2015 Nippon OTIS Elevator. All rights reserved.
M20
Hardness 70 M12
Home Elevator New Noriai-go Wide 20 (Model No. K08B) Installation and Adjustment Manual OTIS CONFIDENTIAL !! 4.4 Install 2nd level of guide rails 4.4.1 Mount plank frame Mount plank frame to guide rails as shown below. 1) Remove rail plumbing gauge from 1st level of guide rail. 2) Mount 2 stoppers to left and right rails at the height of 1650 mm from pit. 3) Suspend • 6 mm 2 m long sling rope by winch between plank channel crossing plank frame and hitch channel. 4) Fit safety block of plank frame into guide rail and hang plank frame down by winch till it hits a stopper.
Copyright© 2015 Nippon OTIS Elevator. All rights reserved.
No. B-(20)-38-e Page
28 of 119
Last translated January 10, 2002
Home Elevator
No. B-(20)-38-e
New Noriai-go Wide 20 (Model No. K08B) Installation and Adjustment Manual
Page
Last translated January 10, 2002
OTIS CONFIDENTIAL !! 4.4.2 Assemble temporary working platform Assemble working platform as shown in the sketch below.
Safety block
Plank frame & platform
Carframe stopper
Cross section
1650 m
Copyright© 2015 Nippon OTIS Elevator. All rights reserved.
29 of 119
Home Elevator New Noriai-go Wide 20 (Model No. K08B) Installation and Adjustment Manual OTIS CONFIDENTIAL !! 4.4.3 Assemble 2nd level of guide rail Assemble 2nd level of guide rails on the platform. 1. Fit 2nd level of guide rail in 1st level of guide rail. No fishplate is used. 2. Fasten rail joint (400 mm long) holes with M12 bolts (4 x 2) and flange nuts (4 x 2). • There should be no gap between 1st and 2nd level of rails.
(Sketch of rail joint)
Copyright© 2015 Nippon OTIS Elevator. All rights reserved.
No. B-(20)-38-e Page
30 of 119
Last translated January 10, 2002
Home Elevator New Noriai-go Wide 20 (Model No. K08B) Installation and Adjustment Manual OTIS CONFIDENTIAL !! 4.5 Mount rail brackets 4.5.1 Procedure to mount rail brackets 1) Mount rail plumbing gauge to the upper part of the 2nd level of guide rail. 2) Mount rail bracket. 3) Plumb the rail brackets in both directions using a plumbing set. 4.5.2 For RC structure
Copyright© 2015 Nippon OTIS Elevator. All rights reserved.
No. B-(20)-38-e Page
31 of 119
Last translated January 10, 2002
Home Elevator New Noriai-go Wide 20 (Model No. K08B) Installation and Adjustment Manual OTIS CONFIDENTIAL !!
Copyright© 2015 Nippon OTIS Elevator. All rights reserved.
No. B-(20)-38-e Page
32 of 119
Last translated January 10, 2002
Home Elevator New Noriai-go Wide 20 (Model No. K08B) Installation and Adjustment Manual OTIS CONFIDENTIAL !! 4.5.3 For steel structure
Copyright© 2015 Nippon OTIS Elevator. All rights reserved.
No. B-(20)-38-e Page
33 of 119
Last translated January 10, 2002
Home Elevator New Noriai-go Wide 20 (Model No. K08B) Installation and Adjustment Manual OTIS CONFIDENTIAL !! 4.5.4 For steel structure with double support
Copyright© 2015 Nippon OTIS Elevator. All rights reserved.
No. B-(20)-38-e Page
34 of 119
Last translated January 10, 2002
Home Elevator New Noriai-go Wide 20 (Model No. K08B) Installation and Adjustment Manual OTIS CONFIDENTIAL !! 4.5.5 For wood structure
Copyright© 2015 Nippon OTIS Elevator. All rights reserved.
No. B-(20)-38-e Page
35 of 119
Last translated January 10, 2002
Home Elevator New Noriai-go Wide 20 (Model No. K08B) Installation and Adjustment Manual OTIS CONFIDENTIAL !!
Copyright© 2015 Nippon OTIS Elevator. All rights reserved.
No. B-(20)-38-e Page
36 of 119
Last translated January 10, 2002
Home Elevator New Noriai-go Wide 20 (Model No. K08B) Installation and Adjustment Manual OTIS CONFIDENTIAL !! 4.6 Assemble car frames 4.6.1 Front door
Copyright© 2015 Nippon OTIS Elevator. All rights reserved.
No. B-(20)-38-e Page
37 of 119
Last translated January 10, 2002
Home Elevator New Noriai-go Wide 20 (Model No. K08B) Installation and Adjustment Manual OTIS CONFIDENTIAL !! 4.6.2 Front and rear doors
Copyright© 2015 Nippon OTIS Elevator. All rights reserved.
No. B-(20)-38-e Page
38 of 119
Last translated January 10, 2002
Home Elevator New Noriai-go Wide 20 (Model No. K08B) Installation and Adjustment Manual OTIS CONFIDENTIAL !! 4.7 Install temporary scaffold 4.7.1 Install temporary scaffold
Sling rope
3 Positions for shackles
• 10 mm shackle (2) • 6 mm 2 m long sling rope (2)
Copyright© 2015 Nippon OTIS Elevator. All rights reserved.
No. B-(20)-38-e Page
39 of 119
Last translated January 10, 2002
Home Elevator New Noriai-go Wide 20 (Model No. K08B) Installation and Adjustment Manual OTIS CONFIDENTIAL !! 4.7.2 Mount 1LS, 2LS, 7LS and 8LS switches Mount them as shown in the sketches below.
2LS 2LS
8LS8LS 7LS 7LS
1LS 1LS
Copyright© 2015 Nippon OTIS Elevator. All rights reserved.
No. B-(20)-38-e Page
40 of 119
Last translated January 10, 2002
Home Elevator New Noriai-go Wide 20 (Model No. K08B) Installation and Adjustment Manual OTIS CONFIDENTIAL !!
No. B-(20)-38-e Page
41 of 119
Last translated January 10, 2002
4.8 Plumb 2nd or above level of guide rails and car frames 4.8.1 Plumb upper end of the 2nd guide rails Mount on the temporary working platform with carframe stopper mounted and fix/align upper part of the 2nd level of guide rails. 1) Set a plumbing set to rails to align rail brackets at the first and second floor. (Use 2 sets of 50 mm plumbs) • Plumbing precision: Allowance should be • 0.5 mm with 50 mm distance between plumb bob and the ground. 2) Fit a plumbing bob to a line passed through center hole ( • 1 mm) of the rail plumbing gauge to the plumb sideways of the rail. • Plumbing precision: Locate the plumbing set 1700 mm or more apart from the ground and allowance should be • 0.5 mm with 50 mm distance between plumb bob and the ground. 3) Fix rail brackets completely. 4) Measure each dimension again and complete the work if there is no problem. 4.8.2 Plumb car frames After aligning guide rails, align car frames. 1) Measure distance between 2 upright channels at both lower and upper end. 2) Where there is a gap between upper and lower distances between upright channels, adjust upper distance to make it the same as lower distance. 3) Fit a plumbing bob to one of the upright channels to make sure of plumb. • Plumbing precision: Locate the plumbing set 1700 mm or more apart from the ground and allowance should be • 0.5 mm with 50 mm distance between plumb bob and the ground. 4) Make sure of the leveling of crosshead channel. • 2 mm or less tolerance in each 1000 mm of length 5) Complete the work if there is no problem.
Copyright© 2015 Nippon OTIS Elevator. All rights reserved.
Home Elevator New Noriai-go Wide 20 (Model No. K08B) Installation and Adjustment Manual OTIS CONFIDENTIAL !!
No. B-(20)-38-e Page
42 of 119
Last translated January 10, 2002
4.8.3 Assemble 3rd and upper levels of guide rails Assemble 3rd and upper levels of guide rails from the temporary scaffold. 1) Fit upper level of guide rail in lower level of guide rail. No fish plate is used. 2) Fasten rail joint (400 mm long) holes with M12 bolts (4 x 2) and flange nuts (4 x 2). • There should be no gap between 1st and 2nd level of rails. 4.8.4 Move temporary scaffold Lift car frame by winch and mount a stopper. 1) Lift temporary scaffold by winch to a position 1m lower than the floor. Do not step on the working platform . 2) Mount stoppers (right and left) to upper end of the 3rd guide rails. 3) Fit sling rope ( • 6 mm, 1.0 m long) and shackle to right and left eyebolt of crosshead channel. 4) Lower the winch and support the load by a stopper in the third section above. 5) There should be no problem in terms of weight, but place winch rope too for safety. 4.8.5 Plumb 3rd and upper levels of guide rails Mount on the temporary working platform with car frame stopper to fix/align 3rd and upper levels of guide rails. 1) Set a plumbing set to rails to align rail brackets at the first and second floor. (Use 2 sets of 50 mm plumbs) • Plumbing precision: Allowance should be • 0.5 mm with 50 mm distance between plumb bob and the ground. 2) Fit a plumbing bob to a line passed through center hole ( • 1 mm) of the rail plumbing gauge to plumb sideways of the rail. • Plumbing precision: Locate the plumbing set 1700 mm or more apart from the ground and allowance should be • 0.5 mm with 50 mm distance between plumb bob and the ground. 3) Fix rail brackets completely. 4) Measure each dimension again and complete the work if there is no problem.
Copyright© 2015 Nippon OTIS Elevator. All rights reserved.
Home Elevator New Noriai-go Wide 20 (Model No. K08B) Installation and Adjustment Manual OTIS CONFIDENTIAL !!
No. B-(20)-38-e Page
Last translated January 10, 2002
4.9 Mount overhead sheave and temporarily install rope 4.9.1 Mount overhead sheave
Mount on the temporary scaffold to mount overhead sheave. 1) Mount a gusset with M12 bolt and nut (4 x 2) in a way upper end of the gusset is as high as 2200-2215 mm. 2) Level upper end of the gusset. 3) Fix the gusset completely. 4) Place overhead sheave on the gusset and fix it with M12 bolt and nut (4).
Copyright© 2015 Nippon OTIS Elevator. All rights reserved.
43 of 119
Home Elevator New Noriai-go Wide 20 (Model No. K08B) Installation and Adjustment Manual OTIS CONFIDENTIAL !!
No. B-(20)-38-e Page
44 of 119
Last translated January 10, 2002
4.9.2 Temporarily install rope Temporarily install rope while there is temporary scaffold. Do not work without wearing safety belt. 1) Pass 2 ropes through the overhead sheave, and temporarily fix (tie off) the rope ends in the pit. 2) As soon as the sockets are fixed to the machine, temporarily fix the middle part of rope to guide rails by binding wire so that ropes do not move. 3) As shown in the sketch next page, place the other end of the rope on the sheave. 4) Fix each rope of the other end to the rails by binding wire. 5) Mount a pin after fixing sockets to the machine. Tool: hexagonal Allen wrench • Do not work in the pit when other workers are working above because rope might slips down.
Copyright© 2015 Nippon OTIS Elevator. All rights reserved.
Home Elevator New Noriai-go Wide 20 (Model No. K08B) Installation and Adjustment Manual OTIS CONFIDENTIAL !!
No. B-(20)-38-e Page
Last translated January 10, 2002
(Sketch for installing rope temporarily)
Machine side
(2) (1) (2) Car hitch side (right) (1)
Car hitch side (left)
Copyright© 2015 Nippon OTIS Elevator. All rights reserved.
45 of 119
Home Elevator New Noriai-go Wide 20 (Model No. K08B) Installation and Adjustment Manual OTIS CONFIDENTIAL !!
No. B-(20)-38-e Page
Last translated January 10, 2002
4.10 Mount sill 4.10.1 Procedure to mount sill Top floor entrance is fit first and lower entrances later. Therefore, mount sills in the same order as entrances.
•
Do not fail to make sure of leveling both longways and sideways.
•
Mount sills connected to entrance
support.
(Sketch for mounting sills)
Copyright© 2015 Nippon OTIS Elevator. All rights reserved.
46 of 119
Home Elevator New Noriai-go Wide 20 (Model No. K08B) Installation and Adjustment Manual OTIS CONFIDENTIAL !! 4.10.2 Sill mounting for RC structure
Copyright© 2015 Nippon OTIS Elevator. All rights reserved.
No. B-(20)-38-e Page
47 of 119
Last translated January 10, 2002
Home Elevator New Noriai-go Wide 20 (Model No. K08B) Installation and Adjustment Manual OTIS CONFIDENTIAL !! 4.10.3 Sill mounting for steel structure
Copyright© 2015 Nippon OTIS Elevator. All rights reserved.
No. B-(20)-38-e Page
48 of 119
Last translated January 10, 2002
Home Elevator New Noriai-go Wide 20 (Model No. K08B) Installation and Adjustment Manual OTIS CONFIDENTIAL !! 4.10.4 Sill mounting with double support for steel structure
Copyright© 2015 Nippon OTIS Elevator. All rights reserved.
No. B-(20)-38-e Page
49 of 119
Last translated January 10, 2002
Home Elevator New Noriai-go Wide 20 (Model No. K08B) Installation and Adjustment Manual OTIS CONFIDENTIAL !! 4.10.5 Sill mounting for wooden structure
Copyright© 2015 Nippon OTIS Elevator. All rights reserved.
No. B-(20)-38-e Page
50 of 119
Last translated January 10, 2002
Home Elevator New Noriai-go Wide 20 (Model No. K08B) Installation and Adjustment Manual OTIS CONFIDENTIAL !! 4.11 Mount jamb 4.11.1 Procedure to mount entrance support Mount 2 entrance support brackets. •
Be sure to level bracket before fastening with bolts.
•
Mount the 3rd bracket at the time of mounting header.
•
Offset dimension is 30 mm.
Offset dimension
Copyright© 2015 Nippon OTIS Elevator. All rights reserved.
No. B-(20)-38-e Page
51 of 119
Last translated January 10, 2002
Home Elevator
No. B-(20)-38-e
New Noriai-go Wide 20 (Model No. K08B) Installation and Adjustment Manual
Page
52 of 119
Last translated January 10, 2002
OTIS CONFIDENTIAL !!
Entrance support dimensions Header
1850 mm - 1900 mm
900 mm
Entrance support bracket
Sill
Copyright© 2015 Nippon OTIS Elevator. All rights reserved.
Home Elevator New Noriai-go Wide 20 (Model No. K08B) Installation and Adjustment Manual OTIS CONFIDENTIAL !! 4.11.2 Procedure to mount jamb Mount jamb as in the sketch below. •
Hall buttons should be in right when you look at them from entrance
•
Fix entrance support bracket to jamb.
•
Jamb installation precision tolerance should be • 1 mm.
(Jamb mounting sketch)
Copyright© 2015 Nippon OTIS Elevator. All rights reserved.
No. B-(20)-38-e Page
53 of 119
Last translated January 10, 2002
Home Elevator New Noriai-go Wide 20 (Model No. K08B) Installation and Adjustment Manual OTIS CONFIDENTIAL !! 4.11.3 Jamb for front door
Copyright© 2015 Nippon OTIS Elevator. All rights reserved.
No. B-(20)-38-e Page
54 of 119
Last translated January 10, 2002
Home Elevator New Noriai-go Wide 20 (Model No. K08B) Installation and Adjustment Manual OTIS CONFIDENTIAL !! 4.11.4 Jamb for rear door
Copyright© 2015 Nippon OTIS Elevator. All rights reserved.
No. B-(20)-38-e Page
55 of 119
Last translated January 10, 2002
Home Elevator New Noriai-go Wide 20 (Model No. K08B) Installation and Adjustment Manual OTIS CONFIDENTIAL !!
Copyright© 2015 Nippon OTIS Elevator. All rights reserved.
No. B-(20)-38-e Page
56 of 119
Last translated January 10, 2002
Home Elevator New Noriai-go Wide 20 (Model No. K08B) Installation and Adjustment Manual OTIS CONFIDENTIAL !! 4.12 Mount header and hoistway door 4.12.1 Mount header 1) Fit header to pins of head jamb. 2) Fix header to head jamb with M6 screw (4). 3) Mount entrance support bracket (2) to rail. 4) Fix entrance support bracket to header with with M6 screw (4). 5) Check/adjust jamb for plumb and squareness. Jamb tolerance should be • 1 mm. 4.12.2 Mount hoistway door 1) Mount slow-speed door. 2) Mount high-speed door. 3) Check each door’s plumb and squareness. • Door inclination: within 1 mm tolerance from top to bottom. 4) Mount unlocking wire at the top floor.
Copyright© 2015 Nippon OTIS Elevator. All rights reserved.
No. B-(20)-38-e Page
57 of 119
Last translated January 10, 2002
Home Elevator New Noriai-go Wide 20 (Model No. K08B) Installation and Adjustment Manual OTIS CONFIDENTIAL !!
Note: This sketch is for reference only. It is a 6-panel door, but 4-panel one.
Copyright© 2015 Nippon OTIS Elevator. All rights reserved.
No. B-(20)-38-e Page
58 of 119
Last translated January 10, 2002
Home Elevator New Noriai-go Wide 20 (Model No. K08B) Installation and Adjustment Manual OTIS CONFIDENTIAL !!
Copyright© 2015 Nippon OTIS Elevator. All rights reserved.
No. B-(20)-38-e Page
59 of 119
Last translated January 10, 2002
Home Elevator New Noriai-go Wide 20 (Model No. K08B) Installation and Adjustment Manual OTIS CONFIDENTIAL !!
Copyright© 2015 Nippon OTIS Elevator. All rights reserved.
No. B-(20)-38-e Page
60 of 119
Last translated January 10, 2002
Home Elevator New Noriai-go Wide 20 (Model No. K08B) Installation and Adjustment Manual OTIS CONFIDENTIAL !! 4.13 Install hoistway equipment 4.13.1 Mount cam for 8LS limit switch Mount cam to fit to A part in the following sketch.
Copyright© 2015 Nippon OTIS Elevator. All rights reserved.
No. B-(20)-38-e Page
61 of 119
Last translated January 10, 2002
Home Elevator New Noriai-go Wide 20 (Model No. K08B) Installation and Adjustment Manual OTIS CONFIDENTIAL !! 4.13.2 Mount cam for 2LS limit switch
Copyright© 2015 Nippon OTIS Elevator. All rights reserved.
No. B-(20)-38-e Page
62 of 119
Last translated January 10, 2002
Home Elevator New Noriai-go Wide 20 (Model No. K08B) Installation and Adjustment Manual OTIS CONFIDENTIAL !! 4.13.3 Mount cam for 1LS limit switch
Copyright© 2015 Nippon OTIS Elevator. All rights reserved.
No. B-(20)-38-e Page
63 of 119
Last translated January 10, 2002
Home Elevator New Noriai-go Wide 20 (Model No. K08B) Installation and Adjustment Manual OTIS CONFIDENTIAL !! 4.13.4 Mount cam for 7LS limit switch
Copyright© 2015 Nippon OTIS Elevator. All rights reserved.
No. B-(20)-38-e Page
64 of 119
Last translated January 10, 2002
Home Elevator New Noriai-go Wide 20 (Model No. K08B) Installation and Adjustment Manual OTIS CONFIDENTIAL !! 4.13.5 Mount sensor for front door and vane
Copyright© 2015 Nippon OTIS Elevator. All rights reserved.
No. B-(20)-38-e Page
65 of 119
Last translated January 10, 2002
Home Elevator New Noriai-go Wide 20 (Model No. K08B) Installation and Adjustment Manual OTIS CONFIDENTIAL !! 4.13.6 Mount sensor for rear door and vane
Copyright© 2015 Nippon OTIS Elevator. All rights reserved.
No. B-(20)-38-e Page
66 of 119
Last translated January 10, 2002
Home Elevator New Noriai-go Wide 20 (Model No. K08B) Installation and Adjustment Manual OTIS CONFIDENTIAL !! 4.13.7 Mount pit flooding sensor
Copyright© 2015 Nippon OTIS Elevator. All rights reserved.
No. B-(20)-38-e Page
67 of 119
Last translated January 10, 2002
Home Elevator New Noriai-go Wide 20 (Model No. K08B) Installation and Adjustment Manual OTIS CONFIDENTIAL !! 4.13.8 Mount Machine Guarding
Machine label should be placed on machine guarding.
Copyright© 2015 Nippon OTIS Elevator. All rights reserved.
No. B-(20)-38-e Page
68 of 119
Last translated January 10, 2002
Home Elevator
No. B-(20)-38-e
New Noriai-go Wide 20 (Model No. K08B) Installation and Adjustment Manual
Page
69 of 119
Last translated January 10, 2002
OTIS CONFIDENTIAL !! 4.13.9 Mount controller
Controller label should be placed on controller top surface.
Copyright© 2015 Nippon OTIS Elevator. All rights reserved.
Home Elevator
No. B-(20)-38-e
New Noriai-go Wide 20 (Model No. K08B) Installation and Adjustment Manual
Page
70 of 119
Last translated January 10, 2002
OTIS CONFIDENTIAL !! 4.13.10 Mount travelling cable hanger Mount travelling cable hanger at the position higher than 1m of the rail in L2.
4.13.11 Mount cab travelling cable hanger Upper cab travelling cable hanger on safety guard
Lower cab travelling cable
hanger
4.13.12 Mount power supply box
Copyright© 2015 Nippon OTIS Elevator. All rights reserved.
Home Elevator New Noriai-go Wide 20 (Model No. K08B) Installation and Adjustment Manual OTIS CONFIDENTIAL !!
No. B-(20)-38-e Page
71 of 119
Last translated January 10, 2002
4. 14 Terminate ropes at car frame 4.14.1 Terminate ropes at car frame With the carframe resting on the buffer, wind the first rope and the second rope around the machine drum 2.0 turns and 1.5 turns respectively. Install the rope wedge sockets as shown below. Note U-bolt should be on the ropes tail end only.
Copyright© 2015 Nippon OTIS Elevator. All rights reserved.
Home Elevator
No. B-(20)-38-e
New Noriai-go Wide 20 (Model No. K08B) Installation and Adjustment Manual
Page
72 of 119
Last translated January 10, 2002
OTIS CONFIDENTIAL !! 4.14.2 Align car frame Align car frame when it is up apart from stopper with rope wound around the machine drum. Adjust rope tension to level car frame sideways. • 2 mm or less tolerance in each 1000 mm of length. Adjust car frame side brace to level car frame longways. • 2 mm or less tolerance in each 1000 mm of length. 4.14.3 How to Operate Machine Brake
Be sure to operate machine brake always with car frame stopper. 1) Remove a dustproof cover with screw (3 units of M4 x 10 as in the sketch 1 below). 2) Insert a brake releasing lever from the top into brake as in the sketch 2 below. 3) Pressing the brake releasing lever to a direction of the arrow in the sketch 2 below, the brake is released. 4) After using the brake releasing lever, remove the lever from the brake and return the dustproof cover to machine brake.
3 screws to mount
Dust-proof
dustproof cover
cover
Sketch 1
When pressed, brake is released
Sketch 2
Copyright© 2015 Nippon OTIS Elevator. All rights reserved.
Home Elevator New Noriai-go Wide 20 (Model No. K08B) Installation and Adjustment Manual OTIS CONFIDENTIAL !! 4.15 Assemble car and safety guard Note: Fix car wiring to car frame before assembling car. It is impossible to fix wiring after car assembly.
Copyright© 2015 Nippon OTIS Elevator. All rights reserved.
No. B-(20)-38-e Page
73 of 119
Last translated January 10, 2002
Home Elevator New Noriai-go Wide 20 (Model No. K08B) Installation and Adjustment Manual OTIS CONFIDENTIAL !! 4.15.1 Car with front door only
Copyright© 2015 Nippon OTIS Elevator. All rights reserved.
No. B-(20)-38-e Page
74 of 119
Last translated January 10, 2002
Home Elevator New Noriai-go Wide 20 (Model No. K08B) Installation and Adjustment Manual OTIS CONFIDENTIAL !!
Copyright© 2015 Nippon OTIS Elevator. All rights reserved.
No. B-(20)-38-e Page
75 of 119
Last translated January 10, 2002
Home Elevator New Noriai-go Wide 20 (Model No. K08B) Installation and Adjustment Manual OTIS CONFIDENTIAL !! 4.15.2 Car with front/rear doors
Copyright© 2015 Nippon OTIS Elevator. All rights reserved.
No. B-(20)-38-e Page
76 of 119
Last translated January 10, 2002
Home Elevator New Noriai-go Wide 20 (Model No. K08B) Installation and Adjustment Manual OTIS CONFIDENTIAL !!
Copyright© 2015 Nippon OTIS Elevator. All rights reserved.
No. B-(20)-38-e Page
77 of 119
Last translated January 10, 2002
Home Elevator New Noriai-go Wide 20 (Model No. K08B) Installation and Adjustment Manual OTIS CONFIDENTIAL !! 4.16 Install operator and car door 4.16.1 Install operator
Copyright© 2015 Nippon OTIS Elevator. All rights reserved.
No. B-(20)-38-e Page
78 of 119
Last translated January 10, 2002
Home Elevator New Noriai-go Wide 20 (Model No. K08B) Installation and Adjustment Manual OTIS CONFIDENTIAL !!
4.16.2 Check car cam position
Check if the white roller is placed on the two grooves of the cam. Roller
Roller
Copyright© 2015 Nippon OTIS Elevator. All rights reserved.
No. B-(20)-38-e Page
79 of 119
Last translated January 10, 2002
Home Elevator
No. B-(20)-38-e
New Noriai-go Wide 20 (Model No. K08B) Installation and Adjustment Manual
Page
80 of 119
Last translated January 10, 2002
OTIS CONFIDENTIAL !! 4.17 Controller wiring 4.17.1 Expanded controller configuration
Cutout 1
Cutout 2
Cutout 3
CTBL 1
Inverter
PFC Board
FG1
PVT PG
(FG 3)
Power Board J_A26807BTG1
J_A21340ABS1 J_A26807BTL1
Control Board
FG2 CTBL 2
J_A26807BTD101
PFC Coil MLF
Rosette PLF
Modular
Fan
Copyright© 2015 Nippon OTIS Elevator. All rights reserved.
Home Elevator
No. B-(20)-38-e
New Noriai-go Wide 20 (Model No. K08B) Installation and Adjustment Manual
Page
Last translated January 10, 2002
OTIS CONFIDENTIAL !! 4.17.2 Connectors on PC board of controller
Power board (J_A26807BTG1)
Connector already connected at factory HL2-3
HPB5C CZ BRK
F1
INV2
F6
HCB3 DCBUS
HCB2 F3
PFC
HSC3
CMSW
F2
RMD2
CPOW
F4
BAT
F5
SVT
HCB1
SC
F7
Control board
CPOW
HPB5P
(J_A26807BTD101)
81 of 119
HPB5P PF2
PVT2
CHECK
(Not used)
PVT1 MTC
EQS
HSC2 HWY1
FDL (Not used)
Copyright© 2015 Nippon OTIS Elevator. All rights reserved.
HWY2
Home Elevator
No. B-(20)-38-e
New Noriai-go Wide 20 (Model No. K08B) Installation and Adjustment Manual
Page
82 of 119
Last translated January 10, 2002
OTIS CONFIDENTIAL !! 4.17.3 Controller wiring Follow the procedures in sections (A)-(F) Note: Marker
is labeled to the connector. Wiring marker
is attached to wire cable.
(A) HJB cable is assembled to a bottom floor jamb.
CMSW
SVT HSC3
TC
DJPS
MCSW
PES-BOX
HSC2
MCS2 PES-BOX
PES
P1 P2
P3
buttons
MCS1
PESB
Already connected to hall
TC
(B) HWAY cable: Diagram below shows wiring for two stop elevator, for your reference.
sensor
HWAY
HWAY
Cable
Cable
HB
PFS
DS
DS
FG
flooding
FG3
DS
FG
Copyright© 2015 Nippon OTIS Elevator. All rights reserved.
floor hall button
HB
Connect to first
TC Pit
hall button
HWY2
Connect to second floor
HWY1
Home Elevator
No. B-(20)-38-e
New Noriai-go Wide 20 (Model No. K08B) Installation and Adjustment Manual
Page
83 of 119
Last translated January 10, 2002
OTIS CONFIDENTIAL !! (C) PES box, battery and service light
Battery BAT
SET TC BAT BAT TC
AC100
HJB Cable
MCSW
PES box PES
HJB cable
No wire
RS
SJ
connection required
PSL
FG1
PSL
Service light Cutout 2
Note: Only phase wire shall be wired from “Cutout 2” to prevent noise
Power Board J_A26807BTG1 FG1
CTBL 1 FG2
RS
CTBL 2
Copyright© 2015 Nippon OTIS Elevator. All rights reserved.
Home Elevator
No. B-(20)-38-e
New Noriai-go Wide 20 (Model No. K08B) Installation and Adjustment Manual
Page
84 of 119
Last translated January 10, 2002
OTIS CONFIDENTIAL !! (D) Wiring motor & DBR resistor
Cables with connector to connect motor and DBR resistor is out from inverter beside PFC board. Wire those cables to motor and DBR resistor. “Motor” and “DBR” are printed respectively on connectors for motor and DBR. When wiring motor cable, connect motor grounding wire to 6th of CTBL1. Note: Cables should be fixed with plastic cable fastener in a way they would not touch “heat sink” behind PFC board. DBR resistor is pre-installed to machine guarding. See the pictures and sketch below.
Cutout 3
Heat sink
Motor cable
Grounding
Cutout 3
wire
CTBL1-6
CTBL 1
MOTOR Inverter
PFC Board
J_A21340ABS1
FG1
J_A26807BTG1
J_A26807BTL1
CTBL 2 FG2
DBR
Power Board
PFC Coil MLF
Copyright© 2015 Nippon OTIS Elevator. All rights reserved.
Home Elevator
No. B-(20)-38-e
New Noriai-go Wide 20 (Model No. K08B) Installation and Adjustment Manual
Page
Last translated January 10, 2002
OTIS CONFIDENTIAL !! (E) Wiring PVT, brake and MTC cables
Fix cables as shown below.
Note: PVT, brake and MTC cables are pre-installed to machine.
Cutout 1 BRK CTBL 1
FG1
PVT FG Power Board J_A26807BTG1
FG2 CTBL 2
85 of 119
(FG 3) Control Board J_A26807BTD101
PVT1 MTC
PVT, brake and MTC cables
Copyright© 2015 Nippon OTIS Elevator. All rights reserved.
Home Elevator
No. B-(20)-38-e
New Noriai-go Wide 20 (Model No. K08B) Installation and Adjustment Manual
Page
86 of 119
Last translated January 10, 2002
OTIS CONFIDENTIAL !! Vinyl tape
(F) Wiring TC cables
Fix cables as shown below.
Parts to be fixed are marked with vinyl tape.
HCB1
2-HPB2
HCB2
12-COM
HCB3
J1
INV1
PES box HJB cable
HWAY cable HJB cable
15-AUX
TC cable
29-HPB3
AC100
TEL
PESB
TEL
30-PIT
DS
26-ECB
DJPS
FG4
CZ
PES box
SET
CTBL1-5
Cutout 3 TEL Inverter
PFC Board
J_A21340ABS1
J_A26807BTL1
INV1
Modular
MLF
PFC coil
Copyright© 2015 Nippon OTIS Elevator. All rights reserved.
rosette
Fan
Home Elevator New Noriai-go Wide 20 (Model No. K08B) Installation and Adjustment Manual OTIS CONFIDENTIAL !!
No. B-(20)-38-e Page
Last translated January 10, 2002
Each cable runs through one of three cutouts. See the following to find out which cable runs through which cutout.
Cutout 1 HJB cable, HWAY cable, one cable from PES box, PVT cable, brake cable, MTC cable, telephone cable
Cutout 2 Two power supply related cables from PES box
Cutout 3 Motor cable, DBR cable
Copyright© 2015 Nippon OTIS Elevator. All rights reserved.
87 of 119
Home Elevator
No. B-(20)-38-e
New Noriai-go Wide 20 (Model No. K08B) Installation and Adjustment Manual
Page
88 of 119
Last translated January 10, 2002
OTIS CONFIDENTIAL !! 4.17.4 Car top controller (or junction box) Note: 1. Marker
is labeled to the connector.
2.
Connector already connected at factory
3. Connectors marked with * are mounted only for cars with front/rear doors
* AGS
* ALR2
* ALR1
LR2
LR1
GS
FG3 FG4 FG1
PC Board
FG2
CLEL
Car light
CF
(option)
J1
TC cable Fan
CFS
COP cable
4.17.5 Connectors on PC board of car top controller (or junction box) LR
SGS
DL COP2 TBZ
ECB DZ
1L2L HPB3 PIT SOS1 SOS2 7LS
8LS
GS
TERM1
* ADZS F2 * ADL
HPB2
* ASGS
Power switch
J_A26807BTE101 for front door only J_A26807BTE201 for front/rear door
* ALR
DIP switch
Note: Those marked with * are only for front/rear doors
DIVI
F7
AUX
F3 F6
FDL (not used) LWD CHK
(not used) COM
* DIV4 *DIV5 DIV2 DIV3
COP
Copyright© 2015 Nippon OTIS Elevator. All rights reserved.
TINS DCDIV TES
Home Elevator
No. B-(20)-38-e
New Noriai-go Wide 20 (Model No. K08B) Installation and Adjustment Manual
Page
89 of 119
Last translated January 10, 2002
OTIS CONFIDENTIAL !! 4.17.6 Car top controller (or junction box) wiring Follow the procedures in sections (A)-(G)
Note: Marker
is labeled to the connector.
Wiring marker
is attached to wire cable.
(A) Cable with 1LS and 2LS are wired to a connector, marked with 1L2L, on PC board in controller.
1L2 L
Cable with 7LS and 8LS are wired to connectors, marked with 7LS and 7LS-2, on PC board in controller. 7LS micro switch cable is connected to 7LS-2
7LS
7LS-2 7LS micro switch
(B) Door zone sensor is wired to PC board.
One sensor for front door only
Additional sensor for front/rear door
ADZS DZS
Copyright© 2015 Nippon OTIS Elevator. All rights reserved.
Home Elevator
No. B-(20)-38-e
New Noriai-go Wide 20 (Model No. K08B) Installation and Adjustment Manual
(C) Light ray device (pre-assembled to side panel) for front door only is wired to connector in car top controller.
LR2
Light Ray Device for front/rear door is wired to connector in car top controller.
ALR1
90 of 119
Last translated January 10, 2002
OTIS CONFIDENTIAL !!
LR1
Page
ALR2
(D) COP and telephone line (pre-assembled to side panel) COP and COP2 are wired to PC board.
CFS is connected to connector in car top controller. TEL is connected to TC cable connector.
CFS
COP
COP2
TEL
(E) Other cables such as SOS1, SOS2, car light cable, car fan cable and LWD cable are all wired to PC board connectors according to their markers.
Copyright© 2015 Nippon OTIS Elevator. All rights reserved.
Home Elevator New Noriai-go Wide 20 (Model No. K08B) Installation and Adjustment Manual OTIS CONFIDENTIAL !!
No. B-(20)-38-e Page
91 of 119
Last translated January 10, 2002
(F) Operator cable For front door only : Connect wires in the sketch below to PC board in car top controller; however, grounding wire is connected to frame grounding terminal in car top controller,and only GS cable is connected to connector in car top controller.
DL GS SGS DIV1 FG2 DIV2 DIV3 FG1
For front/rear doors : Connect wires in the sketch above and below to PC board in car top controller; however, grounding wire is connected to frame grounding terminal in car top controller, and only AGS cable is connected to connector in car top controller.
ADL AGS
ASGS
Male
DIV1
Female
DIV1
DIV1 on front door side
FG2
DIV4 DIV5
FG1
Copyright© 2015 Nippon OTIS Elevator. All rights reserved.
Home Elevator New Noriai-go Wide 20 (Model No. K08B) Installation and Adjustment Manual OTIS CONFIDENTIAL !! (G) TC cable
No. B-(20)-38-e Page
92 of 119
Last translated January 10, 2002
Marker
Fix cables as shown below. Parts to be fixed are marked with vinyl tape.
TC cables are wired to PC board, grounding wire is connected to frame grounding terminal in car top controller, and only J1 and TEL cable are connected to connector in car top controller.
HCB1 HCB2
Already wired to pit controller
HCB3
TC cable
INV1 AC100
2-HPB2
12-COM
PESB TEL
DS
15-AUX J1
29-HPB3
30-PIT TEL
DJPS CZ SET
CTBL1-5
Copyright© 2015 Nippon OTIS Elevator. All rights reserved.
FG4 26-ECB
Home Elevator
No. B-(20)-38-e
New Noriai-go Wide 20 (Model No. K08B) Installation and Adjustment Manual
Page
93 of 119
Last translated January 10, 2002
OTIS CONFIDENTIAL !! See the wiring diagram below.
Safety guard
C 4 FG3 FG
B FG1
PC board
A
FG2
Fix with plastic cable
Safety
fastener
guard
Safety guard
LR2 cable, SOS1/2 cable, ADZ cable, lighting cable, fan cable, TC cable, 7LS-2 cable, 7L/8L cable and LWD cable run through Rou A above.
Operator cable, 1L/2L cable, DZ cable and LR1 cable run through Route B above. COP cable and telephone cable run through Route C above.
4.17.7 Setting car top controller DIP switch Set car top controller DIP switch at site according to DIP switch setting diagram delivered from factory.
Copyright© 2015 Nippon OTIS Elevator. All rights reserved.
Home Elevator New Noriai-go Wide 20 (Model No. K08B) Installation and Adjustment Manual OTIS CONFIDENTIAL !!
No. B-(20)-38-e Page
Last translated January 10, 2002
5. Adjustment In this chapter, the following are discussed for adjusting and testing the home elevator equipment after installation:
5.1 Adjustment sequence flowchart 5.2 Insulation test/power supply voltage measurement 5.3 DIP switch setting 5.4 Test run 5.5 Rope tension/rope guard check 5.6 Running clearance/car installation check 5.7 Safety adjustment 5.8 Doors/door-related components adjustment 5.9 Learn run 5.10 Load weighing device adjustment
Copyright© 2015 Nippon OTIS Elevator. All rights reserved.
94 of 119
Home Elevator New Noriai-go Wide 20 (Model No. K08B) Installation and Adjustment Manual OTIS CONFIDENTIAL !!
No. B-(20)-38-e Page
95 of 119
Last translated January 10, 2002
5.1 Adjustment sequence flowchart Pre-test run Wiring OK
Insulation resistance OK
No obstacle for pre test run?
Power supply voltage OK
Switch on and check power supply voltage for each operation circuit
Check safety chain circuit Test run
Check machines in hatch
Check car guide roller, safety, rope tension, running clearance, limit switches, car door, hatch door and vane
Prepare for normal operation Check if elevator stops when each safety switch is activated
Check if door operate smoothly
Check if safety operates properly
Check if learn run is done Normal operation
Check if load weighing device is adjusted
Riding quality and leveling OK?
Undergo handover inspection and other inspections if required
Handover
Copyright© 2015 Nippon OTIS Elevator. All rights reserved.
Home Elevator New Noriai-go Wide 20 (Model No. K08B) Installation and Adjustment Manual OTIS CONFIDENTIAL !!
No. B-(20)-38-e Page
96 of 119
Last translated January 10, 2002
5.2 Insulation test/power supply voltage measurement 5.2.1 Power supply preparation When main power (100V, 200V) is available, use it for adjustment. When only stand-by power (100V) is available, adjust test run with setup transformer/stand-by power cable (tool). Reference: Setup transformer specification (Hama Denki Industries’) (Input 100V AC, output 100V-0-100V, output current 12.5A, weight 21 kg, 50/60 Hz and class H) Note: Normal operation is possible only with no load with stand-by power supply. 5.2.2 Insulation test Remove jumper wire of HL 1 and measure insulation at the spots next page in pit controller. (Measurement preparation) 1. Turn MC switch in a bottom floor hall button box off. 2. Mount car frame stopper (at two places) 3. Remove pit controller cover. 4. Turn NFBE and NFBL in pit controller off. 5. Remove jumper wire between HL1 -FG. (Measurement spot) 1. FG-NFBE (200V) (specified value: 10M • or more) 2. FG-NFBE (100V) (specified value: 10M • or more) 3. FG-machine UVW terminal (specified value: 5M • or more) 4. FG-HL1 (specified value: 1M • or more) Note: When measured value is less than specified, do not turn the power on till you find out the cause. (Restoration) Put back the jumper wire between HL1-FG.
Copyright© 2015 Nippon OTIS Elevator. All rights reserved.
Home Elevator New Noriai-go Wide 20 (Model No. K08B) Installation and Adjustment Manual OTIS CONFIDENTIAL !! 5.3 DIP switch setup Set up DIP switch on PC board in car top controller according to the setup diagram delivered from factory.
(Factory shipment setup) ON
1
SW1-1:
LPM
2
3
4
5
6
ON = 1/2 speed mode for temporary power Off = rated speed mode
Floor (number of floors) setup (SW1-2/SW1-3) SW1-2: SW1-3:
2 stop 3 stop 4 stop Off On Off Off
invalid Off
On
On
On
Operation mode setup (SW1-4/SW1-5)
Normal Operation for Inspection before operation demonstration shipment SW1-4: Off On Off SW1-5: Off Off On SW1-6: DS_LWO On = No load weighing buzzer Off = Load weighing buzzer
Copyright© 2015 Nippon OTIS Elevator. All rights reserved.
No. B-(20)-38-e Page
97 of 119
Last translated January 10, 2002
Home Elevator New Noriai-go Wide 20 (Model No. K08B) Installation and Adjustment Manual OTIS CONFIDENTIAL !!
No. B-(20)-38-e Page
98 of 119
Last translated January 10, 2002
5.4 Test run 5.4.1 Test run preparation Prepare for a test run according to the following procedure: 1) Check if grounding wire in circuit breaker box for the building is connected to FG terminal in PES box of elevator controller. 2) Turn on the electricity to the breaker exclusively for elevator (100 V, 200 V) in the building. 3) With a tester, check if specified voltage is in line voltage of NEBE (200 V) and NFBL (100 V) in PES box. (tolerance within • 5%) 4) Press “PES switch” of pit controller to make a car inoperative 5) Turn on the electricity to NEBE (200 V) and NFBL (100 V). 6) With a tester, check if specified voltage is in controller voltage of NEBE (200 V) and NFBL (100 V) in PES box. 7) Put cover on pit controller. 8) Operator shall leave pit. 5.4.2 Test run 5.4.2.1 Test run at bottom floor Go down to elevator hall in the bottom floor to start test run. Before test run, check if 1) car frame stopper is mounted 2) “PES” switch is pressed and it is operative 3) MC switch on the back of bottom floor hall buttons is turned off. ( Procedure )
1. Turn “TES” of car top controller off. 2. Select “NOR” of “INS/NOR changeover switch” in car top controller. 3. Select “INS” of “INS/NOR changeover switch” on the back side of bottom floor hall button panel. 4. Turn “PES switch” off to make the car operative. 5. Close hatch door. 6. Turn MC switch on the back of bottom floor hall buttons on. 7. Press “U” and “C” switch on the back side of bottom floor hall button panel simultaneously to make sure car goes up. * If the car would not go up, 2LS switch might be activated. 8. Press “D” and “C” switch on the back of bottom floor hall buttons simultaneously to make sure car goes down. * If the car would not go up, 1LS switch might be on.
Copyright© 2015 Nippon OTIS Elevator. All rights reserved.
Home Elevator New Noriai-go Wide 20 (Model No. K08B) Installation and Adjustment Manual OTIS CONFIDENTIAL !!
No. B-(20)-38-e Page
99 of 119
Last translated January 10, 2002
5.4.2.2 Safety devices check (bottom floor) Drive a car up and down to check if safety devices operates properly. Do not fail to mount car frame stopper when you operate in the pit. Check point (common to both up and down operation) 1) When the bottom floor doors are open, the car would not go up or down. 2) When PES switch is turned on, the car would not go up or down. 3) When MC switch on the back of bottom floor hall buttons is turned off, the car would not go up or down. 4) When 7LS switch is turned on, the car would not go up or down. Check point (down operation only) 1) When 1LS switch is turned on, the car would not go down.
Copyright© 2015 Nippon OTIS Elevator. All rights reserved.
Home Elevator New Noriai-go Wide 20 (Model No. K08B) Installation and Adjustment Manual OTIS CONFIDENTIAL !!
No. B-(20)-38-e Page 100 of 119 Last translated January 10, 2002
5.4.3.1 Test run on car top Conduct test run on car top. Before test run, select “INS” of “INS/NOR changeover switch” on the backside of bottom floor hall buttons. Note: TINS has priority over HINS; therefore, when TINS is operative, HINS becomes inoperative. (Procedure)
1) Turn on the inspection switch of the bottom floor hall button to move the car up to a position where an operator can ride on the car top. 2) Leave “INS” of “INS/NOR changeover switch on the backside of bottom floor hall buttons on. 3) Open hatch doors at the second floor and fix them with a door stopper. 4) Turn on TES from the second floor. 5) Turn on TINS from the second floor and check that car would not move. 6) Ride on car top and close hatch door. 7) Turn off TES. 8) Press “D” and “C” switch simultaneously to make sure car goes down. * When 1LS is turned on, car would not go down. 9) Press “U” and “C” switch simultaneously to make sure car goes up. * When 2LS is turned on, car would not go up. 5.4.3.2 Safety devices check (car top) Drive a car up and down to check if safety devices operates properly. Check point (common to both up and down operation) 1) When the floor door is open at each floor, the car would not go up or down. 2) When TES switch is turned on, the car would not go up or down. 3) When the hatch door is open at each floor, the car would not go up or down. 4) When 8LS switch is turned on, the car would not go up or down. Check point (up operation only) 1) When 2LS switch is turned on, the car would not go up. 2) When WLS (over-winding limit switch) is pressed, the car would not go up.
Copyright© 2015 Nippon OTIS Elevator. All rights reserved.
Home Elevator New Noriai-go Wide 20 (Model No. K08B) Installation and Adjustment Manual OTIS CONFIDENTIAL !!
No. B-(20)-38-e Page 101 of 119 Last translated January 10, 2002
5.5 Rope tension/rope guard check Start test run to check if two ropes’ tension is equal. Check if rope guard is parallel to rope drum and its distance to rope is 3mm or less.
5.6 Running clearance/car installation check Running clearance/car Installation check is already done at the time of installation, but check them again at test run. Check running clearance first and then check car installation precision. • Clearance: 10 mm • 2 mm
•
Parallelism between car sill and hatch door: within • 2 mm
Check opening dimension, car uprightness and door clearance.
• •
Opening dimension: 800 mm Car uprightness: check with plumb bob (tolerance should be within • 1 mm)
Copyright© 2015 Nippon OTIS Elevator. All rights reserved.
Home Elevator New Noriai-go Wide 20 (Model No. K08B) Installation and Adjustment Manual OTIS CONFIDENTIAL !!
No. B-(20)-38-e Page 102 of 119 Last translated January 10, 2002
5.7 Safety adjustment 5.7.1 Check safety block’s clearance Check with a thickness gauge to see if the clearance between the rail and the block is equal to that between the rail and the roller.
5.7.2 Safety operated switch (SOS) adjustment Make clearance between SOS’s roller and actuating plate 1 mm in normal condition.
Angle for SOS switch Make clearance 1 mm •
Since safety block and guide shoe are both well adjusted before shipment from factory, you basically make no adjustment at job site.
•
After adjustment, activate safety to make sure SOS is electrically operated.
•
Make 1 mm clearance between actuating plate and a roller.
Copyright© 2015 Nippon OTIS Elevator. All rights reserved.
Home Elevator New Noriai-go Wide 20 (Model No. K08B) Installation and Adjustment Manual OTIS CONFIDENTIAL !!
No. B-(20)-38-e Page 103 of 119 Last translated January 10, 2002
5.7.3 Follow the procedures below to make sure that safety operates properly 1. Place rated load in a car. 2. Since an operator works in the pit, mount car stopper to the rail in a position as high as 1200-1400 mm from the pit. 3. Set a jack for car on a buffer (remove rubber). 4. Run the car down in the inspection run and make sure SOS operates. 5. Loosen angle mounting bolts to release SOS. 6. Run the car up to cancel safety. 7. Readjust angle to make 2 mm clearance and fix it with bolts. 8. Remove jack for car. 9. Put rubber back to buffer. 10. Make sure that safety does not bungles during down operation (see 5.7.1). 11. Check safety impression. 12. Modify rails with file. 13. Remove car stopper mounted in section 2 and leave the pit.
Copyright© 2015 Nippon OTIS Elevator. All rights reserved.
Home Elevator
No. B-(20)-38-e
New Noriai-go Wide 20 (Model No. K08B) Installation and Adjustment Manual
Page 104 of 119 Last translated January 10, 2002
OTIS CONFIDENTIAL !! 5.8 Doors/door-related components adjustment 5.8.1 Check/adjust door installation and friction •
Procedures to check door installation and friction.
1) Fully open the door and check if each door is flush with entrance column.
Make sure that they are flush. When doors are fully open.
Should be flush
When doors are tightly closed.
Front View of Car Frame
•
Top View of Car Door
When doors are not flush with entrance column, make another adjustment.
2) Open and close the doors manually to see if there is any door friction (such as chatter). Check if guide shoe is securely mounted and there is no trash in sill groove or track rail.
400 mm 200 mm 3) Check jamb, hatch door, entrance column and car door construction tolerances.
Copyright© 2015 Nippon OTIS Elevator. All rights reserved.
Home Elevator
No. B-(20)-38-e
New Noriai-go Wide 20 (Model No. K08B) Installation and Adjustment Manual
Last translated January 10, 2002
OTIS CONFIDENTIAL !! 5.8.2 Hoistway door adjustment Make sure clearance of latch part of interlock in header at each floor is 1.5 ~ 2 mm.
Switch box
Bracket
Page 105 of 119
1.5 ~ 2 mm Interlock Adjust side-to-side
Copyright© 2015 Nippon OTIS Elevator. All rights reserved.
Home Elevator New Noriai-go Wide 20 (Model No. K08B) Installation and Adjustment Manual OTIS CONFIDENTIAL !!
No. B-(20)-38-e Page 106 of 119 Last translated January 10, 2002
5.9 Learn run 5.9.1 Check the followings before starting Learn run 1) Car top controller is in “NOR.” 2) 1LS and 2LS are already mounted. 3) Wiring 1LS and 2LS are completed. 4) Cam for 1LS and 2LS is already mounted. 5) Door zone sensor is already mounted. 6) Door zone vane is already mounted at each floor. 7) PC board at the back of bottom hall buttons is in “INS.” 8) Floor is set by DIP switch in HCDIII-C board of pit controller. (See section 3) 5.9.2 Learn run operation 1) Car goes down to search 1LS. 2) Car goes down to search bottom floor door zone vane in 1LS. Note: There are two door zone vanes in 1LS in case of front/rear door while front door only has only one door zone vane. When it is the case, make sure that setting of install parameter is changed. 3) Finding bottom floor door zone vane in 1LS, the car stops. 4) Car goes up to search door zone vane at the second floor. 5) Car goes up to search 2LS. 6) Car goes up to search door zone vane at the third floor. 7) Finding door zone vane at the third floor, the car stops.
Copyright© 2015 Nippon OTIS Elevator. All rights reserved.
Home Elevator
No. B-(20)-38-e
New Noriai-go Wide 20 (Model No. K08B) Installation and Adjustment Manual
Page 107 of 119 Last translated January 10, 2002
OTIS CONFIDENTIAL !! 5.9.3 Learn run operation by bottom floor hall button
switch changeove r INS/NOR DIP switch
(How to set up ) 1) Turn DIP switch “LEARN” on the back of bottom floor hall button “ON.”
ON
ON
OFF
OFF (Back of bottom floor hall button)
2) Select “NOR” of INS/NOR changeover switch on the back of bottom floor hall button. NOR
NOR
INS
INS
3) Start Learn run. 4) Turn DIP switch “LEARN” on the back of bottom floor hall button “OFF” to finish.
ON
ON
OFF
OFF
Copyright© 2015 Nippon OTIS Elevator. All rights reserved.
Home Elevator New Noriai-go Wide 20 (Model No. K08B) Installation and Adjustment Manual OTIS CONFIDENTIAL !!
No. B-(20)-38-e Page 108 of 119 Last translated January 10, 2002
5.9.4 Learn run operation by service tool Learn run feature operation Example:
LEARN=1 PVT=2 Run=3 Door=4
u af:02 up/DZT A:07345 L:07100
1
When 1 is selected in calibration function menu, the Learn run field is activated. Press GO ON key according to service tool display.
DIP-S LEARN is ON!!
Switch off Top of car ins
Switch on
When the Learn run is started with DIP switch (HSCB dsw1-1), you cannot start the Learn run with service tool and the display shows the message in the left. When you turn the DIP switch off, you can start the Learn run with service tool.
When the top of car inspection switch (TINS) is not in NOR mode, an operator might be on the car top. In order to avoid an accident, the Learn run cannot be started with service tool and the message in the left is displayed. If TINS is shifted to NOR mode, the message will be changed to the next.
When the Learn run menu is selected in normal mode, the instruction to shift to the inspection mode.
Inspection.
to start learn run press GO ON
1LS, 2LS Dist. to term. floor=0000
Switch back to
When hall inspection switch (HINS) is shifted to INS or it is already in inspection mode, press GO ON key to assure the Learn run mode.
Specified distance between 1LS and 2LS is indicated as 0000 from set value of E2PROM parameter ACCEL NTSD.
Make sure that actual distance is the same as the displayed set value, and press GO ON key.
When the inspection switch is returned to normal mode, the Learn run will start.
Normal
1 af:22 3333333 A:44444 L:55555
1
= Running direction (u: up, d: down, -: stop) 22 = Actual floor ••: position fault 3333333 =
Learn run status 444444 = Distance from bottom floor (mm) * about 2000 mm is offset as pit depth 555555 = Learned distance (mm)
LEARN FINISHED!! Press
LEARN FINISHED!! Hw
ENTER
length: 666666
Learn finished successfully
After the learn run, the status is displayed as FINISHED!! and when ON or OFF keys are pressed, display message changes over to hoistway length (666666) as shown above. When ENTER key is pressed, the learned value is automatically written on the floor table in flash memory.
Copyright© 2015 Nippon OTIS Elevator. All rights reserved.
Home Elevator New Noriai-go Wide 20 (Model No. K08B) Installation and Adjustment Manual OTIS CONFIDENTIAL !!
No. B-(20)-38-e Page 109 of 119 Last translated January 10, 2002
Sequence of learn run status indication on display 1)
INACTIVE
Learn mode is selected and car is parked.
2) UP/ ILS
If car parks within 1LS when the Learn run starts, car runs up to the outside of 1LS and
3) DOWN ILS
After the car stops, it turns around to run downward. If car parks at the outside of 1LS,
stops. here is the starting point. 4) DOWN BFL
After checking 1LS, the car runs to the bottom floor door zone with set value of No. of DZ in 1LS in E2PROM and learn 1LS distance.
5) DO /DZB
The car keeps running until DZB sensor comes out from the door zone vane. After the car stops, it turns around to run upward. Then the car keeps running upward to the floor set by E2PROM parameter TOP FLOOR, learning the position where input signal of DZT/DZB sensor turns on/off.
6) UP DZT
Learning the position where DZT sensor comes into door zone vane.
7) UP DZ
Learning the position where DZ sensor comes into door zone vane.
8) UP DZB
Learning the position where DZB sensor comes into door zone vane.
9) UP /DZT
Learning the position where DZT sensor comes out from door zone vane.
10) UP /DZ
Learning the position where DZ sensor comes out from door zone vane.
11) UP /DZB
Learning the position where DZB sensor comes out from door zone vane.
12) DOWN TFL
The car keeps running until DZI sensor comes out from the door zone vane at the top floor. After the car stops, it turns around to run downward to the level of the top floor. When a blind floor is set on door table, floor table is recalculated after stop.
13) EXZ WRIT
Writing floor table of the blind floor to E2PROM.
14) FINISHED
Indicating a message that Learn run is completed.
Error messages during Learn run NOTE: When error is detected during operation, the car immediately stops and an error message is displayed. NO LEARN ERROR
No error.
1LS DISTAN ERROR
Distance between 1LS and the vane at the bottom floor is not the same as specified.
2LS DISTAN ERROR
Distance between 2LS and the vane at the bottom floor is not the same as specified.
SWITCH SEQ ERROR
Input order of DZ1, DZ, DZ2 sensor is abnormal.
PCI READIN ERROR
There is abnormality in position reference function in a board (board malfunction, noise)
NO 1LS AT ERROR
No 1LS input though the car is on the bottom floor.
NO 2LS AT ERROR
No 2LS input though the car is on the top floor.
E2P WRITE DISABL
Light protect switch of E2PROM is not in ENABLE.
NO BOTTOM FLR
Even after running longer than set value after finding 1LS, the bottom floor cannot be detected.
LEARN CANCELED
ENTER key might be pressed during Learn run or inspection switch is cut off.
LANDING SET ERR
Landing setting of the bottom floor and top floor is set blind.
Copyright© 2015 Nippon OTIS Elevator. All rights reserved.
Home Elevator New Noriai-go Wide 20 (Model No. K08B) Installation and Adjustment Manual OTIS CONFIDENTIAL !!
No. B-(20)-38-e Page 110 of 119 Last translated January 10, 2002
5.10 Load weighing device adjustment Load weighing device (LWD) is of micro switch type. * Do not fail to make sure of braking force at 125% load. 5.10.1 Micro switch (LWD) adjustment LWS (Overload)
Adjust load weighing device to make micro switch be activated when load exceeds 105% of the rated capacity and is within 110%. Put 200 kg weight on the floor and add 20 kg. Adjust load weighing device to make a switch be activated in this condition.
5.10.2 Conduct load test Place an ammeter, voltmeter and speedometer at the hall to measure current, voltage and speed. Here, conduct load test at load % required by laws and regulations and check if the data are the same as those specified in the motor label.
Copyright© 2015 Nippon OTIS Elevator. All rights reserved.
Home Elevator
No. B-(20)-38-e
New Noriai-go Wide 20 (Model No. K08B) Installation and Adjustment Manual
Page 111 of 119 Last translated January 10, 2002
OTIS CONFIDENTIAL !! 5.11 References 5.11.1 Parameters
Note: Do not change any setting at site except hoistway-related parameters. 5.11.1.1 Installation parameters (M-1-3-1) (Hoistway-related parameters)
Indication
Min.
Max. Default
Setting
Description
Top Floor
1
3
1
JOB
No. of top floor, but DIPSW setting has priority
No. of DZ in 1LS
1
2
1
JOB
No. of door zones in 1LS zone
No. of DZ in 2LS
1
2
1
JOB
No. of door zones in 2LS zone
floor char of 1F
0
19
1
1
Bottom floor CPI display setting
floor char of 2F
0
19
2
2
Second level CPI display setting
floor char of 3F
0
19
3
3
Third level CPI display setting
floor char of 4F
0
19
4
4
Fourth level CPI display setting
(Door control parameters) Normal door time
0
254
151
15
Door time in normal operation
Opn Hold Set tim
10
249
20
20
Time to press DOB when setting open hold (x100ms)
OpnHold tim x10s
18
254
18
18
Door open hold time (x 10 sec)
DOB lock det tim
0
254
20
20
DOB lock detection time (if sec: 0, detection is invalid)
LRU lock det tim
0
254
30
30
LRU lock detection time (if sec: 0, detection is invalid)
SGS lock det tim
0
254
30
30
SGS lock detection time (if sec: 0, detection is invalid)
Ena SGS ropn num
1
254
30
30
No. of times to detect abnormal SGS continuous reversal
LRU lock resp NY
0
254
1
1
Response when detecting LRU lock 0: No response, 1: LRU invalid
SGS lock resp NY
0
254
0
0
Response when detecting SGS lock 0: No
SGSropnLock resp
0
254
0
0
DS/GS reopn tim
1
100
5
5
DS/GS err respns
0
2
1
1
response, 1: SGS invalid Response when detecting SGS reopen lock 0: No response, 1: SGS invalid Time to open door by DOB, LRU and re-close (sec) when detecting cam has come off
Response when detecting cam has come off 0 :Close door after fully open, 1: Close door immediately
DS/GS delay toll
1
100
20
20
Time to detect cam has come off (x 100 ms)
Ena SGS on delay
0
250
20
20
Delay time from SGD off to validate SGS (100 ms)
DTO detect time
0
254
10
10
Time to detect DTO (sec)
DTC detect time
0
254
15
15
Time to detect DTC (sec)
Copyright© 2015 Nippon OTIS Elevator. All rights reserved.
Home Elevator
No. B-(20)-38-e
New Noriai-go Wide 20 (Model No. K08B) Installation and Adjustment Manual
Page 112 of 119 Last translated January 10, 2002
OTIS CONFIDENTIAL !! (Run control parameters)
Indication
Min. Max. Default Setting
BAT Rescue floor
0
255
255
Description JOB
The floor to which car goes in case of power failure; the nearest down-below floor for 255 (Note: When set value is 0, car goes to the bottom floor. Since car is set to go downward as a rule, car always goes to the nearest down-below floor though you set the fourth floor as rescue floor)
PTR drop delay
0
254
0
0
Time (x 100 ms) from turning LB signal off to turning PTR signal off when a car stops running
relay delay time
0
254
35
35
Time from turning UD relay on to turning PTR on (x 10 ms)
Enable Relevl NY
0
1
1
1
Setting re-leveling function; set 0, and re-leveling is banned
Max Relevel run
1
254
5
5
Max. no. of re-leveling run at a same floor
Relevel err resp
0
1
1
1
Control at a time of re-leveling error 0: Emergency stop, 1: Slowdown and stop
Low Spd Rel tout
0
70
20
20
Time to detect motor lock at a time of re-leveling control (sec)
Inspection type
0
3
2
2
Setting for start delay/stop during inspection run 0: Start 3 sec. delay/emergency stop 1: Start without delay/emergency stop 2: Start 3 sec. delay/control stop 3: Start without delay/control stop
Max No Pos Rescu
10
254
10
10
Setting times of retrying when controller cannot detect car position, and when door zone is not detected after retrying set times, operation
MLB fail det tim
0
254
5
5
RTR drop err cyc
0
20
3
3
Time to detect RTR drop error (x 10 ms)
No of ECS retry
0
254
2
2
No. of times to retry automatic signaling when using RMD
IIC filter cycle
0
4
1
1
No. of S/W filter cycle for IIC buss input
LR pickup delay
0
254
0
0
Parking time with door open and car light off (x 10 ms)
DoorEnegizeDlay
4
254
10
10
Parking time with door open during door de-energizing (x 100 ms)
DS rebound limit
1
254
20
20
Time to detect door switch rebound (x 10 ms)
CC LR time x10s
1
254
6
6
Time to turn car light off after responding to car call (x 10 s)
HC LR time x10s
1
254
18
18
Time to turn car light off after responding to hall call (x 10 s)
OSS trip percent
100
254
130
130
Overspeed detecting time (ratio to rated speed %)
OSS trip det cyc
3
20
5
5
Overspeed detecting filter (cyc: 10 ms/cyc)
REFUSE DSP TYPE
0
1
1
1
Buzzer control after landing at the nearest floor when detecting
PFS SHD wait tim
2
40
3
3
will stop Time to detect CHKLB is always on (100 ms) when a passenger evacuate by himself/herself
flood/earthquake Shortest waiting time after activating flood sensor until main power supply is interrupted (mim)
Copyright© 2015 Nippon OTIS Elevator. All rights reserved.
Home Elevator
No. B-(20)-38-e
New Noriai-go Wide 20 (Model No. K08B) Installation and Adjustment Manual
Page 113 of 119 Last translated January 10, 2002
OTIS CONFIDENTIAL !! 5.11.1.2 Profile parameters (M-1-3-2) Indication
Min. Max.
Default
Setting Description
Velocity NORMAL
10
500
333
333
Setting rated speed (mm/s)
Accelera NORMAL
10
1200
385
385
Setting max. accelerated velocity for normal run (mm/s 2)
Jerk NORMAL
10
2400
385
385
Setting jerk for normal run (mm/s 3)
Velocity INSpect
10
640
200
200
Setting velocity for inspection run (mm/s)
Accelera INSpect
10
1200
385
385
Setting max. accelerated velocity for inspection run (mm/s 2)
Velocity LEARN
10
300
50
50
Setting velocity for learn run (mm/s)
Accelera LEARN
10
1200
500
200
Setting max. accelerated velocity for learn run (mm/s 2)
Velocity Relevel
5
100
15
15
Setting velocity for relevel run (mm/s)
Accelera Relevel
10
1200
385
385
Setting max. accelerated velocity for relevel run (mm/s 2)
Velocity Recover
10
200
100
100
Setting max. car accelerated velocity when controller cannot
Accelera Recover
10
1200
385
385
Setting car velocity when controller cannot detect car position (mm/s 2)
Velocity slow
10
200
60
60
Setting velocity for slow speed operation (mm/s)
Velocity JPSDO
0
200
0
0
Setting velocity for JPSD operation (mm/s)
Velocity ReInit
10
200
100
100
Setting velocity for correction run (mm/s)
Accelera ReInit
10
1200
500
500
Setting accelerated velocity for correction run (mm/s 2)
Accelera NTSD
10
1200
300
300
Accelerated velocity during NTSD operation (mm/s 2)
Velocity Zero
0
10
3
3
Counts per Revol
0
1500
200
200
Rated pulse number of PVT or PPT (ppr)
Motor Speed rpm
0
2000
1061
1061
Motor axis (PVT axis) speed (rpm) when running with rated speed
JPSDO type TBA
0
2
0
0
Setting terminal to conduct JPSDO
Gain fixed posct
10
40
20
20
Jerk gain value for slowdown and stop in normal/relevel run
Destination Lead
0
10
0
0
Correction distance subtracted per cycle from destination
Destination Lag
0
10
3
3
Correction distance added per cycle to destination
Level Tolerance
0
10
1
1
Level tolerance for normal/relevel run (mm)
Zero Speed Time
0
1000
200
200
Time from when targeted distance becomes within level tolerance and detected speed becomes below stop tolerance velocity until when command is completed in FXG control at time of stopping at landing in
detect car position (mm/s)
normal run or relevelling run mode BKL to MOV Toul
0
200
0
0
Time from receiving LB signal to starting velocity command (ms)
Position Displmt
0
25
0
0
Setting for correcting slippage error occurring for approx. 30 ms in position correction by door zone sensor
1LS/2Lstolerance
0
1000
200
200
Tolerance (mm) between a position 1LS/2LS actually detected and a position learned during the learn run
Slippage toleran
0
1000
2002
200
Slippage tolerance (mm)
Jerk TIMED
0
2400
500
500
Jerk (mm/s 3) in timed deceleration
Veloc profile 2
0
300
100
100
Velocity (mm/s) during emergency power operation and LPM operation
Accel profile 2
10
1200
300
300
Max. accelerated velocity (mm/s 2) during emergency power
Jerk profile 2
10
2400
300
300
operation and LPM operation
Jerk (mm/s 3) during emergency power operation and LPM operation
Copyright© 2015 Nippon OTIS Elevator. All rights reserved.
Home Elevator
No. B-(20)-38-e
New Noriai-go Wide 20 (Model No. K08B) Installation and Adjustment Manual OTIS CONFIDENTIAL !!
Page 114 of 119 Last translated January 10, 2002
Indication
Min. Max.
Default Setting
Description
Veloc profile 3
0
300
50
50
Not used
Accel profile 3
10
1200
300
300
Not used
Jerk profile 3
10
2400
300
300
Not used
elta Tc
0
300
100
100
Setting drive control delayed time, subtract ordered speed x Delta TC from destination distance and correct stop position
Decel / Accel %
70
100
100
100
Setting deceleration control ratio against acceleration setting
Veloc OS test
0
1100
100
100
Not used
PreJerk Pos Delt
0
100
5
5
Distance (mm) equivalent to motor speed to shift to normal profile with pre-jerk control
PreJerk Ramp Dlt
1
20
3
3
Acceleration (mm/s/cyc) per 20 ms with pre-jerk control
PreJerk Ramp Cyc
1
50
6
6
Time (x 20 ms) accelerating with pre-jerk control
Ena PreJerk Vel
0
1
1
1
In order to reduce shock at a time of starting, set prejerk function to limit
[ms]
acceleration of the speed per 20 ms until confirming motor speed becomes equivalent to the speed detected by PVT PreJerk tout lim
0
50
20
20
Pre-jerk time out time (x 100 ms)
1LS/2LS distance
0
2190
1175
1175
Distance (mm) between terminal floor and 1LS/2LS - Not used
5.11.1.3 Engineering parameters (M-1-3-4) Indication
Min. Max. Default Setting Description
MLB type 0-2
0
1
1
1
Not used
Recover type 0-1
0
1
1
1
Rescue running direction when controller cannot detect car position in JOB with 2 stops 0: Only run downward 1: After over run downward, run upward
no CUD drop tol
10
254
30
30
Setting no CUD drop detection time x 10 ms
DBSS ICD version
0
1
1
1
Communication specification with SH (fixed with 1)
HDCB ICD version
0
1
1
1
Not used
DRIVE type
0
7
2
2
Not used
0-3
0
3
3
3
Not used
Ccall cutout flr
0
3
0
JOB
Setting car call cut off floor (Customer can set on COP)
Hcall cutout flr
0
3
0
JOB
Setting hall call cut off floor (Customer can set on COP)
Home Landing flr
0
3
0
JOB
Setting home landing floor (Customer can set on COP)
Home Landing tim
0
254
0
JOB
Home landing actuation delay (Customer can set with COP)
PVT DIRECTION
0
1
1
1
PVT direction signal setting
PVT TRANCE DELAY
0
254
30
15
Not used
sleep mode time
0
255
15
15
Time to change over to energy saving operation during parking (min)
IOS Landing flr
0
255
255
255
Parking floor when IOS is off. If 255 is set, parking floor cannot be set
reboot wait time
5
254
150
150
Time (x 100 ms) to start reboot function when a car parks between floors
reboot wait flag
0
2
0
0
Flag set for HCB5 self-resetting during rebooting Do not modify at site
RMD type
- 0: 10 sec., 1: 10 min.
Copyright© 2015 Nippon OTIS Elevator. All rights reserved.
Home Elevator
No. B-(20)-38-e
New Noriai-go Wide 20 (Model No. K08B) Installation and Adjustment Manual OTIS CONFIDENTIAL !!
Page 115 of 119 Last translated January 10, 2002
Indication
Min. Max. Default Setting Description
L_EDGE DELAY LRN
0
254
10
10
Correct delay in forwarding car position information at door zone edge during learn run
L_EDGE DELAY NOR
0
254
0
0
Correct delay in forwarding car position information at door zone edge during normal run
SPARE 1
0
254
0
-
Spare
SPARE 4
0
254
0
-
Spare
0
254
200
200
Distance (mm) detected while DZ sensor is working
SPARE 6
0
254
1
-
Spare
SPARE 7
0
254
1
-
Spare
Demo Type 0-2
0
2
0
0
Demonstration operation setting - Do not modify at site
DEMO Hcall pend
20
254
50
50
Hall call cancellation time setting in demonstration operation Do not modify at site
DEMO door time
20
254
50
50
Door time setting in demonstration operation - Do not modify at site
DEMO reopen time
5
254
25
25
Setting of time (x 100 ms) between door closing start and door revert open in demonstration operation - Do not modify at site
OverHeat protect
0
254
0
0
Setting door motor overheat protection
Abs oversp % NOR
0
254
110
110
Speed to detect overspeed in normal run
Abs oversp % INS
0
254
110
110
Speed to detect overspeed in inspection run
Abs oversp % REC
0
254
110
110
Speed to detect overspeed in recover run
Abs oversp % REI
0
254
110
110
Speed to detect overspeed in correction run
Track err % NOR
1
254
25
25
Speed to detect tracking error in normal run
Track err % INS
1
254
25
25
Speed to detect tracking error in inspection run
Track err % LOW
1
254
200
200
Speed to detect tracking error in relevel run
max# Abs overspd
0
254
3
3
Max. number of overspeed to shut operation down
max# track.retry
0
254
5
5
Max. number of tracking errors to shut operation down
max# track. err
0
254
5
5
Tracking error detection cycle (x 100 ms)
max# tract. loss
0
254
5
5
Max. number of traction loss to shut operation down
max# UX DX fault
0
254
5
5
Max. number of UX DX fault to shut operation down
max# Pos faults
0
254
5
5
Max. number of position fault to shut operation down
max# PVT faults
0
254
5
5
Max. number of PVT fault to shut operation down
max# rdyrun tout
0
254
5
5
Max. number of “RTR in tout” to shut operation down
max# brake tout
0
254
5
5
Max. number of “CLB in tout” to shut operation down
max# drive fault
0
254
5
5
Max. number of drive fault to shut operation down
max# unsafe strt
0
254
5
5
Max. number of “unsafe to start” to shut operation down
max# adv brk flt
0
254
0
0
Max. number of fault when advance lift brake is actuated to shut operation down
CP1 analog out0
0
254
0
-
Check pin CP1-1‘s output setting (analog)
CP1 analog out1
0
254
1
-
Check pin CP1-2‘s output setting (analog)
CP1 degital out0
0
254
0
-
Check pin CP1-3‘s output setting (digital)
CP1 degital out1
0
254
1
-
Check pin CP1-4‘s output setting (digital)
CP1 degital out2
0
254
2
-
Check pin CP1-5‘s output setting (digital)
CP1 degital out3
0
254
3
-
Check pin CP1-6‘s output setting (digital)
DZ Input err tol
Copyright© 2015 Nippon OTIS Elevator. All rights reserved.
Home Elevator
No. B-(20)-38-e
New Noriai-go Wide 20 (Model No. K08B) Installation and Adjustment Manual
Page 116 of 119 Last translated January 10, 2002
OTIS CONFIDENTIAL !! 5.11.1.4 CPI indication in normal operation
CPI indicates the floor the car stops at or the car call floor registered. The CPI indication of each floor can be defined freely by setting the hoistway-related parameters in accordance with the settings below: Setting Indication
Setting Indication
0
7
1
8
2
9
3
10
4
11
5
12
When Lobby floor
6
13
When penthouse
indication is set
indication is set
In addition to floor indications above, CPI can show the following indications as well:
Door open hold
Car position
Detection of
detection failure
SGS/DOB/LR U working
Overload (Upper “o” and
ESS actuation (“E”
lower “o” are indicated
and “5” are
alternately at intervals of
indicated alternately
1 second with continuous
at intervals of 1
alarm sound)
second)
Copyright© 2015 Nippon OTIS Elevator. All rights reserved.
Home Elevator
No. B-(20)-38-e
New Noriai-go Wide 20 (Model No. K08B) Installation and Adjustment Manual
Page 117 of 119 Last translated January 10, 2002
OTIS CONFIDENTIAL !! 5.11.2 Error log checklist
Be sure to check for the records shown below before filling out an error log checklist by checking with a service tool.
M-1-2-2-1 (RAM)
No. of runs - R (
)
Startup time - T (
)
M-1-2-2-2 (E2P)
No. of runs - R (
)
Startup time - T (
)
The error log checklist is shown below and on the following page. 1/4 Code
Indication
2/4 No. of errors Time elapsed Code
Error display
0000
0050 RMD tout err
0001 Div by Zero
0051 RMD pari err
0002 Not availble
0052 RMD orun err
0003 Suprious int
0053 RMD fram err
0004 Fst task ovr
0054 RMD comm err
0005 Lock up HB
0055 RMD undef Rx
0006 Lock up UB
0056 Errlog resp
0007 Lock up DB
0057
0008
0058
0009
0059 RMD TxBuf ov
0010 DZ seq. Error
0060 PGE sync err
0011 Pos mes flt
0061 FXG timeout
0012 POS fault
0062 Dist go err
0013
0063 Overshoot
0014
Inv flr cnt
0064 nor run tout
0015
Inv raw pos
0065 MTC operated
0016 Low Inv spd
0066
0017 High Inv spd
0067 Home landing
0018 1LS error
0068 EQC operated
0019 2LS error
0069
0020 SVT tout err
0070 Door Tim Opn
0021 SVT pari err
0071 Door Tim Cls
0022 SVT orun err
0072 Over Load
0023 SVT fram err
0073 DOL DFC act
0024 SVT comm err
0074 Lock up DOB
0025 SVT undef Rx
0075 Lock up LRU
0026 E2P read fit
0076 Lock up SGS
0027
0077 SGS ropn loc
Inv DEMO set
0028 Dip sw rd er
IOS operated
factory test
0078 DS/GS inp er
0029 Fmem mismach
0079 DS rebound
0030 H
0080 Correct run
tout err
0031 H
pari err
0032 H
orun err
0033 H
0081 Recover run 0082 Relevel run fram err
0083
Inspect run
0034 H
comm err
0084 CUD drop err
0035 H
undef Rx
0085 RTR drop err
0036 H
SIO refr
0086 CLB drop err
0037 H
Txf rest
0038 H 0039 H
0087 CUD in tout reset
TxBuf ov
0088 RTR in tout 0089 CLB in tout
0040 DBC tout err
0090 no CLB drop
0041 DBC pari err
0091 no RTR drop
0042 DBC orun err
0092 no CUD drop
0043 DBC fram err
0093 BL drop err
0044 DBC comm err
0094 missing DZ
0045 DBC undef Rx
0095 DZ fail
0046 DBC Buff clr
0096
invalid MDS
0047 DBC tout rst
0097
invalid MLS
0048 DBC
0098 DBD fault
0049 DBC TxBuf ov
0099 REINIT err
Copyright© 2015 Nippon OTIS Elevator. All rights reserved.
No. of errors Time elapsed
Home Elevator
No. B-(20)-38-e
New Noriai-go Wide 20 (Model No. K08B) Installation and Adjustment Manual
Page 118 of 119 Last translated January 10, 2002
OTIS CONFIDENTIAL !!
3/4 Indication
Code
4/4 No. of errors Time elapsed Code
Indication
0100 OSS trip
0150 Belt Slip
0101 DBP fail
0151 Abelt Slip
0102 ESS operated
0152 Tension fail
0103 SOS operated
0153 ATensionfail
0104 DFC emergstp
0154 DoorMecLoad
0105 BAT low volt
0155 ADoorMecLoad
0106 Battery flt
0156 Latch fail
0107 Adoor INVflt
0157 ALatch fail
0108 PES inp err
0158 DFC opn strt
0109 1LS/2LS oprt
0159 D/GS opn DED
0110
0160 DBF OCT
Illegal mov
0111 DBP input er
0161 DBF Err CT
0112 U/D inp err
0162 DBF Err CS
0113 SAF operated
0163 DBF Err ENC
0114 MLB operated
0164 DBF Err K4
0115 Door INV flt
0165 DBF Err DV
0116 Ovr Load stp
0166 DBF OVT
0117 Unsafe start
0167 DBF OST
0118 Abs over spd
0168 DBF 0DV
0119 go to shtdwn
0169 DBF Mot Lock
0120 DFC input err
0170 DBF UVT
0121 Tracking err
0171 DBF MTC
0122 Traction los
0172 DBF Fin THR
0123 PVT dir err
0173 DBF Elec THR
0124 1LS/2LS loss
0174 DBF Err ABZ
0125 BPSF/PF shdn
0175 DBF CautTrip
0126 DZ input
0176 DBF CPU err
0127 MLBT failure
0177 DBF PFC THR
0128 6LS operated
0178 DBF
0129 5LS operated
0179 DBF
0130 RELEVEL err
0180 DRV type mis
0131
0181 DRIVE reset
rdy/brk err
0132 BL in tout
0182 D-INV reset
0133 no BL drop
0183 HPB5 reset
0134 Power fail
0184 HCB5 reset
0135 LFR operated
0185
0136 Torque limit
0186 PFS operated
0137 Drive fault
0187 sleep mode
0138
INS-LIM fit
INS operated
0139 Motor lock 0140 Big pos slip 0141 Big neg slip 0142 0143 0144 0145
IIC comm err 0146 0147 0148 0149
Copyright© 2015 Nippon OTIS Elevator. All rights reserved.
No. of errors Time elapsed
Home Elevator
No. B-(20)-38-e
New Noriai-go Wide 20 (Model No. K08B) Installation and Adjustment Manual OTIS CONFIDENTIAL !!
Description
Date
01-Jan-15 Newly issued
Copyright© 2015 Nippon OTIS Elevator. All rights reserved.
Page 119 of 119 Last translated January 10, 2002