31 0 210KB
Receiver / Decoder DRP Family DRP 364, 373, 375, 385
Menu Guide
BLANKOM Digital GmbH TecCenter 31162 Bad Salzdetfurth Germany Tel. +49 (0) 5063 / 2711-0 Fax +49 (0) 5063 / 2711-60 Menu Guide - Receiver / Decoder DRP Family Rev 1.0
Receiver / Decoder DRP Family DRP 364, 373, 375, 385 List Of Contents
General Operating Instructions.............................................. 3 Main Level Menu.................................................................. 4 Front End Menu DRP 364 - ASI............................................ 5 Front End Menu DRP 375 - COFDM ...................................... 5 Front End Menu DRP 373 - QPSK ......................................... 6 Front End Menu DRP 385 - QAM .......................................... 7 Decoder Menu ..................................................................... 8 Video / Audio Menu.............................................................. 9 Video / Audio Menu............................................................ 10 Additional Menu................................................................. 11 Communication Interface Menu ........................................... 12 Common Interface Menu / Time Menu / Info Menu ................ 13 Default Configuration (Factory Settings) ............................... 14 Logbook Entries................................................................. 15 Logbook Entries................................................................. 16 RS 232 Interface – Command Overview ............................... 17 RS 232 Interface – Command Syntax................................... 20 Ethernet Interface – Command Syntax................................. 20
Blankom Digital
Rev 1.0
Receiver / Decoder DRP Family DRP 364, 373, 375, 385 General Operating Instructions Operation with pushbuttons The device is operated via the front panel keypad, supported by alphanumerical information in a background illuminated LC display. Menus provide for adjusting and query parameters. Use the buttons to select menu items for parameter displaying and changing or, in the adjustment mode, to select certain parameters within a menu and to modify values or decimals. The arrows in the display show in which direction you can move within the menu level. To store the modification, press ENTER. The fallback menue appears automatically after 5 minutes without button operation or by presssing the buttons and simultaneously.
1381 MHz BBC Prime
5.1dB
Display of receiption frequency, C/N reserve and service name. (Ex. of QPSK-Receiver, display depending on DRP type)
Adjustment Mode You can only change parameters in the adjustment mode. Simultaneously press the arrow keys ⊳ and hold them down while pressing 3 times ENTER. The adjustment mode deactivates automatically after 3 minutes without button operation or by pressing the ENTER button for more than 2 seconds.
Reset A Reset performs a restart of the software. The DRP is initialized and will start with the latest stored configuration of the customer. All stored parameters remain the same. Simultaneously press the arrow keys and and hold them down while pressing 3 times ENTER.
Preset A Preset performs a restart of the software with default settings. The DRP is initialized and will start with the configuration set by the factory. All stored parameters will be erased and set to default values! Simultaneously press the arrow keys and and hold them down while pressing 3 times ENTER.
Rev 1.0
Blankom Digital
3 / 20
Receiver / Decoder DRP Family DRP 364, 373, 375, 385 Main Level Menu
54MBit/s BBC PRIME v DRP364-1N V2.13 (V1.07) v FRONT-END ASI
Fall back menu (depending on frontend type)
DRP type and options Software version application + (firmware ethernet option)
Depending on front end type
v DECODER v VIDEO/AUDIO v ADDITIONAL v COMMUNICATION INTERFACE v COMMON INTERFACE v DATE 25.10.04 TIME 20:12:53 v LOG SCRIPT (example: DRP 364-1)
4 / 20
Blankom Digital
Rev 1.0
Receiver / Decoder DRP Family DRP 364, 373, 375, 385 Front End Menu DRP 364 - ASI
Main level
Level 2
54MBit/s BBC PRIME v FRONT-END ASI
v DECODER
54 MBit/s 188 Bytes
Input data rate and supported packet size
v INPUT RATE 54 Mbit/s
Selection input data rate
v PACKET SIZE 188 Bytes
Selection packet size
v TSID / ONID 0x044D / 0x0001
Transport stream ID and
[54] [72] Mbit/s
[188] [204] bytes
original network ID
Front End Menu DRP 375 - COFDM
Main level 594.0 MHz NDR FS NDS
Level 2
>24dB
v FRONT-END COFDM
v DECODER
594.0 MHz 8 MHz
Input frequency and channel bandwidth
v FREQUENCY 594.0 MHz
Selection input frequency
v CH BANDWIDTH 8 MHz
Selection channel bandwidth
v TSID / ONID 0x044D / 0x0001
Transport stream ID and
v BIT ERROR RATE = 10E-5 / 7 = BER >= 10E-7 / 9 = BER >= 10E-9 - = not active
ST
DRP 373 - QPSK Command AP
LNB
LNB22 SY ZF
Parameter
Description
?
Display SCPC transport stream ID and SCPC status
xxxx
Set SCPC transport stream ID
?
Display LNB setting
14
Set remote power supply to 14 V
18
Set remote power supply to 18 V
off
Deactivate remote power supply and control signal
on
22 kHz control signal on
off
22 kHz control signal off
?
Display configured sympol rate
xx.xxxx
Set symbol rate in MSymbol/s
?
Display configured input frequency
xxxx
Set input frequency in MHz
DRP 375 - COFDM Command CHBW COFDMPAR
Parameter
Description
?
Display configured channel bandwith
7
Set channel bandwith to 7 MHz
8
Set channel bandwith to 8 MHz
?
Polling COFDM transmission parameters
DRP 385 - QAM Command RF SY QAM
Rev 1.0
Parameter
Description
?
Display configured input fequency
xxx.x
Set input frequency in MHz
?
Display configured sympol rate
x.xxxx
Set symbol rate in MSymbol/s
?
Display configured QAM constellation size
xxx
Set QAM constellation size
Blankom Digital
17 / 20
Receiver / Decoder DRP Family DRP 364, 373, 375, 385 DRP Common Commands Command
Parameter
Description
&S
Display of all parameters (incl. DRP type and software version)
&W
Preset (restart with factory settings) ?
Display audio gain
AG
dec
Decrease audio gain
inc
Increase audio gain
AL
?
Display available audio language according to table ID
Xx
Selection of audio language by table ID
AM AS
AT
?
Polling audio mode
?
Display output aspect ratio
43
Set output aspect ratio to 4:3
+12dB to –6dB at 0,5dB steps -6dB to –30dB at 3dB steps
auto
Set output aspect ratio to original input aspect ratio
l/on
Audio test sound left on
l/off
Audio test sound left off
r/on
Audio test sound right on
r/off
Audio test sound right off
CAM
?
Display CAM system
CAVER
?
Display hardware version of CA board
CD
?
Polling UTC date (e.g.: 06,07,04)
CN
?
Polling C/N reserve in dB (calculated margin to BER 2.0E-4)
CNI
?
Display configured VPS CNI code
xxx
Set VPS CNI Code
CT
?
Polling UTC time (e.g.: 14,26,23)
?
Display echo status
on
Activate echo function
EC
off
Deactivate echo function
EV
?
Polling of actual and next event (event name + VPS start time)
ID
?
Display of DRP type
INVID
?
Polling of aspect ratio and resolution of MPEG input signal
?
Polling muting status of original encoded WSS line (line 23)
0
Removing of encoded original WSS line (line 23) during letterbox mode off
1
Removing of encoded original WSS line (line 23) during letterbox mode on
clear
Clear log script
xxx
Polling 20 log script entries starting from position xxx
LBXWSSMUTE
LS
MU
PA
?
Display status of muting function (h = enabled, l = disabled)
xxxx
Enable/Disable muting functions xxxx = [AFC][BER][PROC][CA] h = high (enable) / l = low (disable)
?
Listing of all services within multiplex with index, service ID and name
xxxx
Selection of a service via service ID
PAS
?
Display configured service with ID, name and ISO639 language descriptor
PIDS
?
Display of video PID / audio PID / teletext PID
PSI
?
Polling PSI table versions of PAT, SDT and PMT
?
Listing of all services within multiplex with name, ID, PMT-PID, Provider + PIDs of configured service
PT
18 / 20
Blankom Digital
Rev 1.0
Receiver / Decoder DRP Family DRP 364, 373, 375, 385 DRP Common Commands Command PZ
RD
Parameter
Description
?
Display status of test line generation
on
Test line generation off
off
Test line generation on
?
Display fall back delay of relay after alarm in seconds
xxxx
Set fall back delay of relay after alarm in seconds
?
Display configured signalling mode
RESET SM
Restart of application (configuration remains)
rem
Set signalling mode to REMOTE ALARM
kbb
Set signalling mode to KBB OPTION
01,00
Protocol termination: i.e. interface activities are terminated, interface distributor #1 takes over control.
xx, yy
Selects a DRP via an interface distributor xx= cabinet address, yy= receiver address. DRP sets the RTS line to ‘LOW’ for 2 seconds. The command is not acknowledged (01 OK or 02 ERROR).
?
Polling muting status and BER-LEDs (A B E P C F 5 7 9 ) A = AFC or AGC-MUTING / B=BER-MUTING / E=ERROR FLAG P = PROC.MUTING / C = CA / F = FAULT 5 = BER >= 1.0E-5 / 7 = BER >= 1.0E-7 / 9 = BER >= 1.0E-9 - = not active
?
Display status test pattern generation
on
Test pattern generation on
SR
ST
TB
off
Test pattern generation off
TSID
?
Polling transport stream ID and original network ID
TT
?
Display status teletext insertion
TX
on
Teletext insertion on
TXTLINES VERFE
VF
VP
off
Teletext insertion off
?
Polling used teletext lines field 1/2
?
Display hardware version of front end
?
Display output video norm
pal
Set output video norm to PAL
secam
Set output video norm to SECAM
ntsc
Set output video norm to NTSC
?
Display status data line 16 / VPS insertion
on
Data line 16 / VPS insertion on
VS
off
Data line 16 / VPS insertion off
WM
?
Display status WSS insertion
WS
on
WSS insertion on
off
WSS insertion off
Rev 1.0
Blankom Digital
19 / 20
Receiver / Decoder DRP Family DRP 364, 373, 375, 385 Option N - Ethernet Command
Parameter
Description
ETHFWVER
?
Display firmware version of ethernet module
?
Display configured gateway address
GATEADDR
xxx.xxx.xxx.xxx Set gateway address ?
IPADDR
Display configured IP address
xxx.xxx.xxx.xxx Set IP address ?
SUBADDR
Display configured subnet mask
xxx.xxx.xxx.xxx Set subnet mask
RS 232 Interface – Command Syntax General commands: Line Feed Carriage Return
ASCII 0A Hex ''Ctrl J'' ASCII 0D Hex ''Return ↵''
Command syntax: (case insensitive) command parameter (n byte) e.g.: TXON => setting the VBI teletext to ON (Enabled) e.g.: LSCLEAR => clear log script Reply syntax: acknowledgement command parameter (n byte) e.g.: AM?
=> 01 OK stereo
e.g.: CAM?
=> 01 OK Cryptoworks
Data is transmitted as: ''ASCII'' Valid commands are acknowledged with: ''01 0K'' Invalid commands are acknowledged with: ''02 Error'' Echofunction can be enabled/disabled.
Ethernet Interface – Command Syntax Protocol : The protocol used for the control over ethernet is UDP using port 4003. The command syntax is the same as used for the RS232 interface.
20 / 20
Blankom Digital
Rev 1.0