Riso RZ Series Error Codes List [PDF]

Zitiervorschau

Riso RZ Series Error Codes By Ali Zghyebeh

Riso RZ Series Error Codes List



     

 



Code: A01-206 Description:Timeout error during master-making operation

Code: A01-211 Description:Master-positioning sensor is ON during standby.

Code: A01-214 Description:Master-positioning sensor is ON at the start of master making. Code: A01-215 Description:Faulty gate-array control for the write pulse motor (motor does not stop within set time) Code: A02-509 Description:Master-loading sensor was OFF when the master was checked at a specified drum angle during the master-loading oper201ation.

‫ﺯﻭ‬ ‫ﺭﻳ‬



Code: A01-202 Description:Master-positioning sensor does not go OFF even when the write pulse motor is reversed during the master-positioning or at start ofmaster-making operation.

‫ﻛﺯ‬ ‫ﻣﺭ‬



Code: A01-201 Description:Master-positioning sensor does not go ON even after the write pulse motor is activated during the master-positioning, master-cut, ormaster-loading operation.

‫ﺧﺩ‬



‫ﻣﺔ‬



 

   

Code: A04-303 Description:Master-disposal jam sensor was OFF at both 120 and 180 degrees drum angle. Code: A04-314 Description:Master-disposal error (recovery error). Code: A05-304 Description:Master-disposal jam sensor was ON at the completion of the master-disposal operation.

‫مركز خدمة ريزو ـ حسان آغا‬

1

Riso RZ Series Error Codes By Ali Zghyebeh



   

 

 

 

Code: A06-403 Description:Paper-feed-tray upper or lower safety switch is OFF. Code: A07-409 Description:Paper-ejection sensor was OFF when the paper should have arrived, and the paper sensor was ON when the machine stopped (Papermisfeed). Code: A07-412 Description:Paper sensor was OFF three times in succession when a paper misfeed was detected (paper misfeed). Code: A07-413 Description:Paper sensor was ON when the paper should have left the paper sensor (long-length paper mode error). Code: A07-418 Description:The paper sensor was ON at the start of machine operation when the START button was pressed. Code: A07-429 Description:Paper feed error (recovery error).

‫ﺯﻭ‬ ‫ﺭﻳ‬



Code: A05-315 Description:The master-disposal jam sensor was ON when the master disposal box was set in the machine.

‫ﻛﺯ‬ ‫ﻣﺭ‬



Code: A05-312 Description:The master-disposal jam sensor was ON at the start of master-making operation.

‫ﺧﺩ‬



‫ﻣﺔ‬



  

 

 

Code: A07-432 Description:Paper sensor was ON when the machine went into paper feed retry movement after a paper misfeed. Code: A08-410 Description:Paper-ejection sensor was OFF when paper should have arrived, and the paper sensor was OFF when the machine stopped (paper jamon the print drum). Code: A08-421 Description:Paper sensor was ON when the paper should have left the paper sensor during feeding of long paper in long-length paper mode (paperlonger than 555 mm).

‫مركز خدمة ريزو ـ حسان آغا‬

2

Riso RZ Series Error Codes By Ali Zghyebeh



 

          

Code: A09-417 Description:Paper-ejection sensor was ON at the start of machine operation when the START button was pressed. Code: A09-431 Description:Paper-ejection error (recovery error). Code: A10-102 Description:Original-registration-sensor remaining jam Code: A10-103 Description:Original-IN-sensor remaining jam

Code: A10-105 Description:Original-registration-sensor non-arrival jam Code: A10-106 Description:Original-IN-sensor non-arrival jam Code: A10-107 Description:Original-OUT-sensor non-arrival jam

‫ﺯﻭ‬ ‫ﺭﻳ‬



Code: A09-411 Description:Paper-ejection sensor was ON when the paper should have left the paper-ejection sensor.

‫ﻛﺯ‬ ‫ﻣﺭ‬



Code: A08-430 Description:Paper jam on print drum (recovery error).

‫ﺧﺩ‬



‫ﻣﺔ‬



       

 

Code: A10-109 Description:An original feed error occurred, due to opening the AF. Code: A10-162 Description:No original in AF during AF master making. Code: A16-525 Description:Waiting for the master to be removed. Code: A17-209 Description:Cutter home-position switch is OFF at the start of master-making or master-set operation. Code: A34-218 Description:Request to resetting the master.

‫مركز خدمة ريزو ـ حسان آغا‬

3

Riso RZ Series Error Codes By Ali Zghyebeh



 

 

 

 

 

Code: B22-727 Description:After cluster-A signal turned ON, BUSY-signal stayed "L" more than 7 seconds (power to job separator was turned OFF while the tape isbeing ejected. Code: B23-722 Description:With the “Tape separation” function set ON, no tape detected in the job separator when the start key is pressed.

Code: B23-723 Description:No tape remains in job separator upon completion of the tape-ejection operation. Code: B24-724 Description:Tape jam detected when the start key is pressed with the “Tape separation” function set to ON. Code: B24-725 Description:Job separator tape-jam detection signal is “H” within 1,200 milliseconds after the cluster-A signal turns ON (tape misfeed). Code: B24-726 Description:Job separator tape-jam detection signal is “L” when the BUSY signal changes from “L” to “H” (or after 7 sec. at “L”) after the cluster-Asignal goes ON (tape misfeed).

‫ﺯﻭ‬ ‫ﺭﻳ‬



Code: B22-721 Description:With the “Tape separation” function set ON, no power is supplied to the job separator when start key is pressed.

‫ﻛﺯ‬ ‫ﻣﺭ‬



Code: B01-730 Description:Keycard counter: No card

‫ﺧﺩ‬



‫ﻣﺔ‬





 

   

 

Code: B31-916 Description:Network cable is not connected when the machine is powered ON. Code: B32-917 Description:Communication error on the network. Code: B32-920 Description:Error detected by Network Interface Card (NIC) - NAK (negative acknowledgement was received). Code: B33-931 Description:DHCP server is not found with DHCP ON. ‫مركز خدمة ريزو ـ حسان آغا‬

4

Riso RZ Series Error Codes By Ali Zghyebeh



   

 

   



Code: C01-563 Description:Ink remaining amount is zero. Code: C01-574 Description:Inkless error was detected 5 times consecutively on one same ink bottle. Code: C02-200 Description:The master end was detected twice in succession at 10milliseconds intervals during master transport. Code: C02-240 Description:Master remaining amount is zero

Code: C03-308 Description:Compression detection position was reached before the master-compression-motor encoder-sensor count reached the specified level,after the master compression motor turned ON in the compression direction. Code: C03-313 Description:Master removal box full detected by the master removal count.

‫ﺯﻭ‬ ‫ﺭﻳ‬



Code: C01-512 Description:The ink sensor did not go ON even when inking was performed for the preset period.

‫ﻛﺯ‬ ‫ﻣﺭ‬



Code: B34-919 Description:Error detected on the locally connected printer.

‫ﺧﺩ‬



‫ﻣﺔ‬



 

 

 

 

Code: C04-402 Description:Paper detection sensor is OFF (no paper on the feed tray). Code: D01-526 Description:Print drum is not set in the machine (drum connection signal, drum safety switch, and drum-lock sensor is OFF. Code: D01-527 Description:Print drum connection signal is OFF when the print drum was inserted in the machine. Code: D01-528 Description:Print drum safety switch is OFF when the print drum was inserted in the machine. ‫مركز خدمة ريزو ـ حسان آغا‬

5

Riso RZ Series Error Codes By Ali Zghyebeh



         

 

Code: D02-532 Description:Incorrect print drum is used. Code: D03-533 Description:Ink cartridge set sensor is OFF. Code: D04-534 Description:Incorrect ink cartridge is used.

Code: D04-560 Description:Ink TAG is not detected on ink bottle.

Code: D04-561 Description:Ink cartridge communication error (communication with the ink cartridge was interfered by noise). Code: D04-562 Description:Wrong ink cartridge information. Code: D04-564 Description:Detected a mismatch in ink cartridge information

‫ﺯﻭ‬ ‫ﺭﻳ‬



Code: D01-530 Description:Print drum connection signal does not go OFF within 5 seconds after the print drum safety switch went OFF when the print drum waspulled out.

‫ﻛﺯ‬ ‫ﻣﺭ‬



Code: D01-529 Description:Print drum lock sensor is OFF when the print drum was inserted in the machine (time-out: 5 seconds).

‫ﺧﺩ‬



‫ﻣﺔ‬



      

 

Code: D05-210 Description:Master detection sensor is OFF (not detecting master). Code: D07-310 Description:Disposal-box safety switch is OFF. Code: D08-224 Description:Master making unit is not set (both the safety switch and lock sensor are OFF). Code: D08-226 Description:Master making unit safety switch is still OFF when the master making unit is set in position.

‫مركز خدمة ريزو ـ حسان آغا‬

6

Riso RZ Series Error Codes By Ali Zghyebeh



 

   

    

Code: D09-212 Description:Master-making-unit set sensor is OFF (sensor light path is free). Code: D11-535 Description:Front cover set switch is OFF.

Code: D13-9 Description:The rear cover is opened (serviceman safety switch is OFF). Code: D17-236 Description:Incorrect master roll.

Code: D17-237 Description:Master roll undetected.

Code: D17-238 Description:Master roll communication error.

‫ﺯﻭ‬ ‫ﺭﻳ‬



Code: D08-228 Description:Master making unit lock sensor is still ON even after the master making unit safety switch went OFF, when the master making unit waspulled out of the machine.

‫ﻛﺯ‬ ‫ﻣﺭ‬



Code: D08-227 Description:Master making unit lock sensor is still OFF when the master making unit is set in position (timeout: 5 seconds).

‫ﺧﺩ‬



‫ﻣﺔ‬



         

Code: D17-239 Description:Wrong master roll detected. Code: D17-241 Description:Detected a mismatch in master roll information. Code: D18-522 Description:Print drum ready for release (solenoid is ON). Code: D19-223 Description:Master making unit ready for release (solenoid is ON). Code: D22-540 Description:Error in access to the Drum PCB (unable to read from or write on the Drum PCB).

‫مركز خدمة ريزو ـ حسان آغا‬

7

Riso RZ Series Error Codes By Ali Zghyebeh   

 

 



Code: E01-10 Description:Battery voltage was less than 2.5 V when the power was switched ON (weak battery: time to replace battery). Code: E02-11 Description:Master counter reached the value set for the maintenance call (value set by test mode). [The message appears when either the power isturned ON, the unit is reset, or when the machine operation ended.] Code: E02-12 Description:Copy counter reached the value set for the maintenance call (value by set test mode). [The message appears when either the power isturned ON, the unit is reset, or when the machine operation ended.] Code: E02-22 Description:Maintenance counter inside the print drum reached the value set for the maintenance call (value set by test mode). [The messageappears when either the power is turned ON, the unit is reset, or when the machine operation ended.]



Code: F01-15 Description:There is no master on the print drum at the start of printing.

‫ﺯﻭ‬ ‫ﺭﻳ‬



‫ﻣﺔ‬

‫ﺧﺩ‬



Code: D22-542 Description:Abnormal data on Drum PCB.

‫ﻛﺯ‬ ‫ﻣﺭ‬



 

   

 

Code: F02-18 Description:Paper size does not match with the image size on the print drum at the start of printing. Code: F03-16 Description:Multi-up was selected using custom size paper. Code: F05-19 Description:In master making, the print quantity selected is less than the minimum print quantity. Code: F10-21 Description:Paper size does not match with the size of image on the print drum when test print is selected and activated.

‫مركز خدمة ريزو ـ حسان آغا‬

8

Riso RZ Series Error Codes By Ali Zghyebeh



 

 

 

 

  

Code: F37-50 Description:Original was set on the AF with book mode selected, when master making is activated. Code: F50-910 Description:Auto-printer-selection is disabled due to error on linked printer. Code: F54-923 Description:Auto-printer-selection is disabled due to no paper in the linked printer. Code: F55-924 Description:Auto-printer-selection is disabled while receiving print data from PC. Code: F58-927 Description:Cannot print from linked printer (Initializing NET-C). Code: H1-566 Description:Requesting ink color information input (Ink-TAG related).

‫ﺯﻭ‬ ‫ﺭﻳ‬



Code: F22-33 Description:Next original is not placed on flatbed for multi-up operation.

‫ﻛﺯ‬ ‫ﻣﺭ‬



Code: F21-32 Description:Next original is not in placed on AF for multi-up operation.

‫ﺧﺩ‬



‫ﻣﺔ‬



 

 

 

 

Code: H2-567 Description:Requesting print density information input (Ink-TAG related). Code: H3-568 Description:Requesting test printing print density information input (Ink-TAG related). Code: H4-242 Description:Requesting master-making density information input (Master-TAG related). Code: H5-243 Description:Requesting Print density information input (Master-TAG related). ‫مركز خدمة ريزو ـ حسان آغا‬

9

Riso RZ Series Error Codes By Ali Zghyebeh



 

 

   

 



Code: P01-521 Description:B-positioning sensor status does not change even after 3,033 pulses after the main motor activates. Code: P01-524 Description:Clamp unit is not at the home position while the print drum is in operation (except during master disposal). Code: P01-537 Description:Print drum failed to stop at position B. (over-run)

Code: P01-538 Description:Print drum is not locked during operation. (Print-drum lock position sensor: OFF) Code: P02-400 Description:Both the upper and lower limit sensors were ON at the same time. Code: P02-401 Description:Overload current was detected in the elevator motor.

‫ﺯﻭ‬ ‫ﺭﻳ‬



Code: P01-520 Description:Main encoder sensor does not go ON/OFF within 10 milliseconds after the main motor activates.

‫ﻛﺯ‬ ‫ﻣﺭ‬



Code: H6-244 Description:Requesting test printing print density information input (Master-TAG related).

‫ﺧﺩ‬



‫ﻣﺔ‬



 

 

 

Code: P02-404 Description:The lower-limit sensor does not go OFF within 2 seconds after the elevator motor operates in the raising direction from the lower-limitposition. Code: P02-405 Description:The upper-limit sensor does not go ON within 12 seconds after the elevator motor operates in the raising direction. Code: P02-406 Description:The upper-limit sensor does not go OFF within 2 seconds after the elevator motor operates in the lower direction from the upper-limitposition.

‫مركز خدمة ريزو ـ حسان آغا‬

10

Riso RZ Series Error Codes By Ali Zghyebeh



 

 

 

 



Code: P03-500 Description:Clamp sensor A is OFF after the completion of the clamp unit initialization or home positioning movement. Code: P03-501 Description:Clamp sensor B does not change within 1 second from the time the clamp motor operates in the correct direction. Code: P03-502 Description:Clamp sensor B does not change within 1 second from the time the clamp motor operates in the reverse direction. Code: P03-503 Description:Clamp sensor A does not go ON within 3 seconds when the clamp unit makes initialization movement. Code: P03-504 Description:At the start of Clamp plate open/close action, the the detection sequence of clamp-sensors A & B is abnormal.

‫ﺯﻭ‬ ‫ﺭﻳ‬



Code: P02-408 Description:The upper-limit sensor is OFF continuously for over 2 seconds during operation of the elevator servo action to raise the feed tray.

‫ﻛﺯ‬ ‫ﻣﺭ‬



Code: P02-407 Description:The lower-limit sensor does not go ON within 12 seconds after the elevator motor operates in the lowering direction.

‫ﺧﺩ‬



‫ﻣﺔ‬



 

 

 

 

Code: P03-505 Description:At the start of print drum Positon-A compensation movement, the detection sequence of clamp-sensors A & B is abnormal. Code: P03-506 Description:At the start of Clamp unit Home-positioning movement, the detection sequence of clamp-sensors A & B is abnormal. Code: P03-507 Description:Clamp sensor A is ON after the clamp release action is completed. Code: P03-508 Description:Clamp sensor A is ON after the A-position compensating movement is completed.

‫مركز خدمة ريزو ـ حسان آغا‬

11

Riso RZ Series Error Codes By Ali Zghyebeh



 

 

 



Code: P05-603 Description:The vertical-centering sensor does not switch ON even when the vertical-positioning pulse motor activated in the imagedown direction for5 seconds during vertical home positioning movement. Code: P05-604 Description:The vertical-centering sensor does not switch OFF even when the vertical-positioning pulse motor activated in the image-up direction for 5seconds during vertical home positioning movement. Code: P05-605 Description:Even though the vertical positioning motor stopped according to the vertical centering sensor detection, the stopping position does notcorrespond with the programmed position. (GA control error).

Code: P05-612 Description:The one-step-positioning key was pressed with verticalprint-position information undefined.

‫ﺯﻭ‬ ‫ﺭﻳ‬



Code: P04-513 Description:The overflow sensor was ON for a set number of times in succession during the 10-millisecond-interval overflow-sensor check.

‫ﻛﺯ‬ ‫ﻣﺭ‬



Code: P03-545 Description:Clamp unit is not in the home position while the print drum is in movement (cause due to the clamp motor).

‫ﺧﺩ‬



‫ﻣﺔ‬



   

 

Code: P08-951 Description:Print job executed was not in correct RisoRinc format. Code: P11-600 Description:Print pressure HP sensor does not switch ON within 3.9 seconds after the print pressure pulse motor activated towards higher pressureduring home positioning operation. Code: P11-601 Description:Print pressure HP sensor does not switch OFF within 4.6 seconds after the print pressure pulse motor activated towards lower pressureduring home positioning operation.

‫مركز خدمة ريزو ـ حسان آغا‬

12

Riso RZ Series Error Codes By Ali Zghyebeh



 

 

 



Code: P12-301 Description:Master compression motor lock when moving compression plate up. Code: P12-305 Description:Master compression sensor does not go ON within 6.5 seconds after the master compression motor operates in the return direction. Code: P12-306 Description:Master compression sensor does not go OFF within 2 seconds after the master compression motor operates in the compress direction. Code: P12-307 Description:Master compression plate maximum position is not detected within 6.5 seconds after the master compression motor operates in thecompress direction.

‫ﺯﻭ‬ ‫ﺭﻳ‬



Code: P12-300 Description:Overload current was detected in the master removal motor.

‫ﻛﺯ‬ ‫ﻣﺭ‬



Code: P11-602 Description:Even though the print pressure control pulse motor stopped according to the print pressure HP sensor detection, the stopping positiondoes not correspond with the programmed position. (GA control error).

‫ﺧﺩ‬



‫ﻣﺔ‬



 

 

 

Code: P12-309 Description:Master-compression-motor encoder sensor count did not change as the master compression motor activated in the compress directionand moved out from the home position. Code: P12-316 Description:Master-compression-motor encoder sensor count did not change within 10 milliseconds after the master compression motor activated. Code: P13-203 Description:Cutter HP switch does not go OFF within 100 milliseconds after the cutter motor is activated.

‫مركز خدمة ريزو ـ حسان آغا‬

13

Riso RZ Series Error Codes By Ali Zghyebeh



 

 

 

 



Code: P13-221 Description:Both the cutter HP switch and cutter stop position switch are ON at the same time. Code: P13-222 Description:Cutter HP switch does not go ON within 450 milliseconds after the cutter home positioning operation started. Code: P13-231 Description:Cutter HP switch does not go OFF within 500 milliseconds after the cutter moved out from the home position.

Code: P13-232 Description:Cutter stop position switch does not go ON within 2 seconds after the cutting operation started.

Code: P13-233 Description:Cutter stop position switch does not go OFF within 500 milliseconds after the cutter activates to move from the stop position to the homeposition.

‫ﺯﻭ‬ ‫ﺭﻳ‬



Code: P13-205 Description:Master-positioning sensor is ON when the print drum rotates through the preset angle following master cutting.

‫ﻛﺯ‬ ‫ﻣﺭ‬



Code: P13-204 Description:Cutter HP switch does not go ON within 300 milliseconds after the cutter motor is activated.

‫ﺧﺩ‬



‫ﻣﺔ‬



 

   

 

Code: P13-234 Description:Cutter HP switch does not go ON within 2 seconds after the cutter home positioning operation started. Code: P14-114 Description:Incorrect main-unit data. Code: P14-115 Description:The scanner operation is not completed within the set time. Code: P14-116 Description:Timeout error for black shading compensation. (RZ3 series only)

‫مركز خدمة ريزو ـ حسان آغا‬

14

Riso RZ Series Error Codes By Ali Zghyebeh



 

     

 



Code: P14-124 Description:Gain adjustment not completed within set time. (RZ3 series only) Code: P14-125 Description:Offset adjustment not completed. Code: P14-126 Description:Gain adjustment not completed.

Code: P14-135 Description:Malfunction detected during offset adjustment. (RZ3 series only) Code: P14-136 Description:Malfunction detected during offset adjustment. (RZ3 series only) Code: P14-137 Description:Malfunction detected during black shading compensation. (RZ3 series only)

‫ﺯﻭ‬ ‫ﺭﻳ‬



Code: P14-123 Description:Offset adjustment not completed within set time. (RZ3 series only)

‫ﻛﺯ‬ ‫ﻣﺭ‬



Code: P14-117 Description:Timeout error for white shading compensation. (RZ3 series only)

‫ﺧﺩ‬



‫ﻣﺔ‬



 

 

 

 

Code: P14-138 Description:Malfunction detected during white shading compensation. (RZ3 series only) Code: P14-170 Description:Even though the read pulse motor stopped according to the sensor detection, the stopping position does not correspond with theprogrammed position. (GA control error). Code: P15-110 Description:ABC (auto-base-control) timeout. The original does not move from the ABC scanning position on the AF unit. Code: P15-111 Description:Operation command was made to the AF unit without 24 volts supplied to the AF unit. ‫مركز خدمة ريزو ـ حسان آغا‬

15

Riso RZ Series Error Codes By Ali Zghyebeh



 

   

 

  

Code: P15-132 Description:Riso printer detected communication sequence error from the AF unit. Code: P15-133 Description:Communication error with AF unit (ACK or NAK error). Code: P15-134 Description:Riso printer could not send command to the AF unit within the set time.

Code: P15-160 Description:AF unit detection signal went OFF while the AF unit is in operation. Code: P15-4 Description:Communication error with AF-CPU. Code: P17-20 Description:Solenoid counter is not connected.

‫ﺯﻭ‬ ‫ﺭﻳ‬



Code: P15-131 Description:Riso printer received an undefined command from the AF unit.

‫ﻛﺯ‬ ‫ﻣﺭ‬



Code: P15-130 Description:Timeout error in receiving reply from the AF unit after command signal was sent from the Riso printer to the AF unit.

‫ﺧﺩ‬



‫ﻣﺔ‬



 

 

 

Code: P18-531 Description:Print drum lock sensor is still ON even after 100 milliseconds after the print drum lock solenoid is activated. Code: P19-207 Description:TPH pressure sensor does not go OFF within 2 seconds after the thermal-pressure motor activates in the decompressing direction, orduring home positioning operation. Code: P19-208 Description:TPH pressure sensor does not go ON within 2 seconds after the thermal-pressure motor activates in the decompressing direction.

‫مركز خدمة ريزو ـ حسان آغا‬

16

Riso RZ Series Error Codes By Ali Zghyebeh



 

 

 

 



Code: P20-415 Description:Paper-ejection-wing home sensor does not go OFF within 7,000 milliseconds after the paper ejection wing motor activates in thecounterclockwise direction from the home position. Code: P20-416 Description:Overload current was detected in the paper-ejection motor.

Code: P20-437 Description:Paper-ejection encoder sensor status does not change within 10 milliseconds after the paper-ejection motor is activated. Code: P24-539 Description:Inking-motor encoder sensor status does not change within 20 milliseconds after the inking-motor is activated. Code: P25-26 Description:Battery voltage was below 2.3 volts (too low) when the power is turned ON.

‫ﺯﻭ‬ ‫ﺭﻳ‬



Code: P19-217 Description:TPH pressure sensor does not go ON within 2 seconds after the thermal-pressure motor activates in the compressing direction.

‫ﻛﺯ‬ ‫ﻣﺭ‬



Code: P19-216 Description:TPH pressure sensor does not go OFF within 500 millisecond after the thermal-pressure motor activates in the compressing direction.

‫ﺧﺩ‬



‫ﻣﺔ‬



 

 



Code: P92-570 Description:EEPROM on the print drum PCB was being accessed while the print drum was in releasing action from the machine. Code: P93-932 Description:No reply from the NET-C network interface card while accessing to the network interface card.



Code: P93-933 Description:No response from NET-C for 90 seconds during NET-C initialization.



Code: P94-225

‫مركز خدمة ريزو ـ حسان آغا‬

17

Riso RZ Series Error Codes By Ali Zghyebeh 

Description:TPH code does not match with the machine code when the power is turned ON with the master-making unit in operating position or whenthe master-making unit is inserted in operating position while the power is ON.



Code: P95-59 Description:Machine serial-number information sent from SH-PCB does not match with the machine serial number information in the MCTL PCB.

   

 

  

Code: P96-433 Description:Paper size width potentiometer test-mode setting is not completed. Code: P96-569 Description:Either the print drum color information or ink category information is still not input. Code: P96-613 Description:Print pressure data missing.

Code: P98-119 Description:Image processing PCB trouble.

‫ﺯﻭ‬ ‫ﺭﻳ‬



Code: P96-172 Description:Scanner adjustment not completed.

‫ﻛﺯ‬ ‫ﻣﺭ‬



Code: P96-171 Description:TPH resistance value not input.

‫ﺧﺩ‬



‫ﻣﺔ‬



     

 

Code: P98-120 Description:Scanner communication problem. (RZ3 series only) Code: P98-129 Description:Faulty Scanner GA PCB. (RZ3 series only) Code: P98-2 Description:No reply from Mini-Rosa PCB when the machine power is turned ON even though the Rosa connection signal is ON. Code: P98-245 Description:Master transfer time-out error during master making (Write pulse motor error).

‫مركز خدمة ريزو ـ حسان آغا‬

18

Riso RZ Series Error Codes By Ali Zghyebeh



         

 

Code: P98-39 Description:Improper EEPROM on the SH-PCB. Code: P98-46 Description:The DIMM capacity does not match. Code: P98-5 Description:Hardware error.

Code: P98-51 Description:Touch-panel communication error

Code: P98-53 Description:Failure in calling out the saved Memory settings (program, mode, user paper information).

Code: P98-54 Description:Failure in saving the Memory settings (program, mode, user paper information). Code: P98-55 Description:Machine type code from SH-PCB does not match with the machine information on the H8-PCB.

‫ﺯﻭ‬ ‫ﺭﻳ‬



Code: P98-38 Description:Machine data on EEPROM does not match with that on the SH-PCB

‫ﻛﺯ‬ ‫ﻣﺭ‬



Code: P98-246 Description:Master transfer time-out error during master making (Load pulse motor error).

‫ﺧﺩ‬



‫ﻣﺔ‬





     

 

Code: P98-6 Description:FRAM checksum error. Code: P98-614 Description:Vertical print position data missing. Code: P98-63 Description:The test-mode memory data stored was outside the adjustment range. Code: P98-64 Description:An undefined command was sent in communication between SH-PCB and MCTL PCB.

‫مركز خدمة ريزو ـ حسان آغا‬

19

Riso RZ Series Error Codes By Ali Zghyebeh



 

 

   

 



Code: P98-68 Description:Communication error 04 between SH-PCB and MCTL PCB (MCTL PCB side). Code: P98-69 Description:Communication error 05 between SH-PCB and MCTL PCB (MCTL PCB side). Code: P98-7 Description:Mini Rosa PCB not connected.

Code: P98-70 Description:Communication error 06 between SH-PCB and MCTL PCB (MCTL PCB side). Code: P98-71 Description:Communication error 07 between SH-PCB and MCTL PCB (MCTL PCB side). Code: P98-72 Description:Communication error 08 between SH-PCB and MCTL PCB (MCTL PCB side).

‫ﺯﻭ‬ ‫ﺭﻳ‬



Code: P98-67 Description:Communication error 03 between SH-PCB and MCTL PCB (MCTL PCB side).

‫ﻛﺯ‬ ‫ﻣﺭ‬



Code: P98-65 Description:Communication error 01 between SH-PCB and MCTL PCB (MCTL PCB side).

‫ﺧﺩ‬



‫ﻣﺔ‬



 

 

 

 

Code: P98-73 Description:Communication error 09 between SH-PCB and MCTL PCB (MCTL PCB side). Code: P98-74 Description:Communication error 10 between SH-PCB and MCTL PCB (SH-PCB side) Code: P98-75 Description:Communication error 11 between SH-PCB and MCTL PCB (SH-PCB side) Code: P98-76 Description:Communication error 12 between SH-PCB and MCTL PCB (SH-PCB side) ‫مركز خدمة ريزو ـ حسان آغا‬

20

Riso RZ Series Error Codes By Ali Zghyebeh



 

 

 

 

 

Code: P98-79 Description:Communication error 15 between SH-PCB and MCTL PCB (SH-PCB side) Code: P98-80 Description:Communication error 16 between SH-PCB and MCTL PCB (SH-PCB side) Code: P98-81 Description:Communication error 17 between SH-PCB and MCTL PCB (SH-PCB side) Code: P98-82 Description:Communication error 18 between SH-PCB and MCTL PCB (SH-PCB side) Code: P98-83 Description:Communication error 19 between SH-PCB and MCTL PCB (SH-PCB side) Code: P98-84 Description:Communication error 20 between SH-PCB and MCTL PCB (SH-PCB side)

‫ﺯﻭ‬ ‫ﺭﻳ‬



Code: P98-78 Description:Communication error 14 between SH-PCB and MCTL PCB (SH-PCB side)

‫ﻛﺯ‬ ‫ﻣﺭ‬



Code: P98-77 Description:Communication error 13 between SH-PCB and MCTL PCB (SH-PCB side)

‫ﺧﺩ‬



‫ﻣﺔ‬





 

 

   

Code: P98-934 Description:Main read/write communication error (detected by read/write side). Code: P98-935 Description:Main read/write communication error (detected by machine side). Code: P98-937 Description:Serial number data missing. Code: P98-938 Description:FRAM version-down.

‫مركز خدمة ريزو ـ حسان آغا‬

21

Riso RZ Series Error Codes By Ali Zghyebeh



         



Code: P98-949 Description:24V-A does not go OFF. Code: P98-950 Description:24V-B does not fo OFF. Code: P98-952 Description:Checksum error on the ROSA flash-memory.

Code: P98-953 Description:Unsuccessful writing on the ROSA flash-memory.

Code: P98-98 Description:Machine serial number information on the SH-PCB EEPROM does not match with that in the FRAM. Code: P99-936 Description:Software error

‫ﺯﻭ‬ ‫ﺭﻳ‬



Code: P98-948 Description:24V-B does not go ON (a possible burnt 24-volt group-B fuse).

‫ﻛﺯ‬ ‫ﻣﺭ‬



Code: P98-947 Description:24V-A does not go ON (a possible burnt 24-volt group-A fuse).

‫ﺧﺩ‬



‫ﻣﺔ‬



‫مركز خدمة ريزو ـ حسان آغا‬

22