Din 5480-2 [PDF]

  • 0 0 0
  • Gefällt Ihnen dieses papier und der download? Sie können Ihre eigene PDF-Datei in wenigen Minuten kostenlos online veröffentlichen! Anmelden
Datei wird geladen, bitte warten...
Zitiervorschau

DEUTSCHE NORM

May 2006

D

DIN 5480-2 ICS 21.120.10

Supersedes: see below

SUPPLIED BY BSB UNDER LICENCE FROM DIN FOR ESCORTS LIMITED - FARIDABAD ON 29/12/2012

Involute splines based on reference diameters – Part 2: Nominal and inspection dimensions Passverzahnungen mit Evolventenflanken und Bezugsdurchmesser – Teil 2: Nennmaße und Prüfmaße

Supersedes DIN 5480-2:1991-10, DIN 5480-3:1991-10, DIN 5480-4:1991-10, DIN 5480-5:1991-10, DIN 5480-6:1991-10, DIN 5480-7:1991-10, DIN 5480-8:1991-10, DIN 5480-9:1991-10, DIN 5480-10:1991-10, DIN 5480-11:1991-10, DIN 5480-12:1991-10, DIN 5480-13:1991-10 and DIN 5480 Corrigendum 1:1995-11.

Document comprises 40 pages

Translation by DIN-Sprachendienst. In case of doubt, the German-language original should be consulted as the authoritative text.

©

No part of this translation may be reproduced without prior permission of DIN Deutsches Institut für Normung e. V., Berlin. Beuth Verlag GmbH, 10772 Berlin, Germany, has the exclusive right of sale for German Standards (DIN-Normen).

English price group 14 www.din.de www.beuth.de

!,z2Z" 9871555

DIN 5480-2:2006-05

Contents

Page

1

Scope ......................................................................................................................................................5

2

Normative references ............................................................................................................................5

3 3.1 3.2 3.3

Graphic representation of dimensions and measurements..............................................................6 Space width/tooth thickness ................................................................................................................6 Diameters................................................................................................................................................6 Inspection dimensions..........................................................................................................................6

4

Module m = 0,5 mm ................................................................................................................................8

5

Module m = 0,6 mm ............................................................................................................................. 10

6

Module m = 0,75 mm ........................................................................................................................... 12

7

Module m = 0,8 mm ............................................................................................................................. 14

8

Module m = 1 mm ................................................................................................................................ 16

9

Module m = 1,25 mm ........................................................................................................................... 18

10

Module m = 1,5 mm ............................................................................................................................. 20

11

Module m = 1,75 mm ........................................................................................................................... 22

12

Module m = 2 mm ................................................................................................................................ 24

13

Module m = 2,5 mm ............................................................................................................................. 26

14

Module m = 3 mm ................................................................................................................................ 28

15

Module m = 4 mm ................................................................................................................................ 30

16

Module m = 5 mm ................................................................................................................................ 32

17

Module m = 6 mm ................................................................................................................................ 34

18

Module m = 8 mm ................................................................................................................................ 36

19

Module m = 10 mm .............................................................................................................................. 38

Bibliography ..................................................................................................................................................... 40 Figures Figure 1 — Space width/tooth thickness..........................................................................................................6 Figure 2 — Diameters .........................................................................................................................................6 Figure 3 — Inspection dimensions ...................................................................................................................6 Figure 4 — Tooth thickness measurement ......................................................................................................7 See foreword for relationship to the ISO 4156 series of standards, including ISO 4156 AMD 1:1992, published by the International Organization for Standardization (ISO).

2

SUPPLIED BY BSB UNDER LICENCE FROM DIN FOR ESCORTS LIMITED - FARIDABAD ON 29/12/2012

Foreword..............................................................................................................................................................3

DIN 5480-2:2006-05

Validity This standard is valid from 2006-05-01.

Foreword

Involute splines in accordance with ISO 4156 are based on module series. These are not interchangeable with involute splines conforming to the DIN 5480 series of standards. The DIN 5480 series of standards is based on reference diameters that are independent of the module, allowing an optimal fit to standard ball and roller bearing diameters and reducing the number of different tools required for manufacturing. This series of standards has been revised by Technical Committee 2.1 Passverzahnungen (“Involute splines”) of the Normenauschuss Maschinenbau (Mechanical Engineering Standards Committee). The revision was considered necessary since a review of the DIN 5480 series of standards in accordance with DIN 820-4 had shown that the series had structural and editorial weaknesses. The object of the revision was to combine the individual parts of this standard in a practical, sensible manner. The entire series of standards now consists of only four parts instead of the previous sixteen. DIN 5480 Involute splines based on reference diameters now comprises: ⎯ Part 1: General ⎯ Part 2: Nominal and inspection dimensions ⎯ Part 15: Inspection ⎯ Part 16: Tools The new edition of DIN 5480-1 deals with fundamental principles, the same as its predecessor, but now also includes fit dimensions and tolerances, these being formerly contained in DIN 5480-14:1986-03. The calculation formulae, tolerances and deviations contained in Part 1 also apply to the other parts of this series of standards. DIN 5480-2 now contains the nominal dimensions and inspection dimensions for the range of items stated above, and incorporates the contents of the former editions of DIN 5480-2 to DIN 5480-13. DIN 5480-15 covers quality inspections of spline joints. DIN 5480-16 defines the design features of tools for manufacturing involute splines.

3

SUPPLIED BY BSB UNDER LICENCE FROM DIN FOR ESCORTS LIMITED - FARIDABAD ON 29/12/2012

This series of standards deals with involute splines and spline joints within a module range of 0,5 to 10, having a number of teeth ranging from 6 to 82 and with a pressure angle of 30°. The DIN 5480 series of standards is limited to splines with a pressure angle of 30°, since pressure angles of 37,5° and 45° are covered by ISO 4156.

DIN 5480-2:2006-05

Amendments

a)

The title has been changed to “Involute splines based on reference diameters”.

b)

The full root radius has been included for shafts.

c)

Cold-rolling has been included as a manufacturing process for shafts.

d)

The measuring circle (ball or pin) diameters have been taken from DIN 3977, with one exception.

e)

The standard has been editorially revised.

Previous editions DIN 5480-2: 1966-12; 1974-09; 1986-03; 1991-10 DIN 5480-3: 1966-12; 1974-09; 1986-03; 1991-10 DIN 5480-4: 1966-12; 1974-09; 1986-03; 1991-10 DIN 5480-5: 1966-12; 1974-09; 1986-03; 1991-10 DIN 5480-6: 1966-12; 1974-09; 1986-03; 1991-10 DIN 5480-7: 1966-12; 1974-09; 1986-03; 1991-10 DIN 5480-8: 1966-12; 1974-09; 1986-03; 1991-10 DIN 5480-9: 1966-12; 1974-09; 1986-03; 1991-10 DIN 5480-10: 1966-12; 1974-09; 1986-03; 1991-10 DIN 5480-11: 1966-12; 1975-12; 1986-03; 1991-10 DIN 5480-12: 1966-12; 1974-09; 1986-03; 1991-10 DIN 5480-13: 1966-12; 1974-09; 1986-03; 1991-10 DIN 5480 Corrigendum 1: 1995-11

4

SUPPLIED BY BSB UNDER LICENCE FROM DIN FOR ESCORTS LIMITED - FARIDABAD ON 29/12/2012

This standard differs from DIN 5480-2:1991-10, DIN 5480-3:1991-10, DIN 5480-4:1991-10, DIN 5480-5:1991-10, DIN 5480-6:1991-10, DIN 5480-7:1991-10, DIN 5480-8:1991-10, DIN 5480-9:1991-10, DIN 5480-10:1991-10, DIN 5480-11:1991-10, DIN 5480-12:1991-10, DIN 5480-13:1991-10 and DIN 5480 Corrigendum 1:1995-11 as follows:

DIN 5480-2:2006-05

1

Scope

a)

They have a standard pressure angle of 30°.

b)

The basic rack profile is the same for all pitches, therefore applying a uniform design rule to all profiles.

c)

They have a side fit profile (a diameter fit is permitted in some cases).

d)

Addendum modification is used in order to achieve specific reference diameters.

e)

The fit system includes tolerances for effective form deviations so that the effect of such deviations on backlash is taken into account. The specified range of fundamental deviations and tolerance classes takes due consideration of all requirements.

Involute spine joints as in this standard are used for connecting hubs and shafts either with a removable connection, a sliding fit or a permanent fit. They have all the characteristics required for centring the parts and transmitting torques, as well as meeting all the requirements for economical manufacturing. The theoretical root diameters for hubs and shafts where the dedendum of the basic rack profile, hfP, is 0,55 ⋅ m. The dedendum depends on the manufacturing method used, and can therefore have various values (see DIN 5480-1, Table 3). The root diameters depend on the dedendum.

2

Normative references

The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. DIN 5480-1, Involute splines based on reference diameters – Part 1: General DIN 5480-15, Involute splines based on reference diameters – Part 15: Inspection DIN 5480-16, Involute splines based on reference diameters – Part 16: Tools

5

SUPPLIED BY BSB UNDER LICENCE FROM DIN FOR ESCORTS LIMITED - FARIDABAD ON 29/12/2012

This standard applies to involute splines and spline joints based on reference diameters for connecting hubs and shafts either with a removable connection, a sliding fit or a permanent fit. It lays down the following general characteristics for splines as in this standard:

DIN 5480-2:2006-05

3.1

Graphic representation of dimensions and measurements Space width/tooth thickness

Figure 1 — Space width/tooth thickness

3.2

Diameters

Key 1 2

Shaft Hub Figure 2 — Diameters

3.3

Inspection dimensions

Key 1 2

Shaft Hub Dimension M2 between 2 measuring circles (balls or pins)

Dimension M1 over 2 measuring circles (balls or pins)

Figure 3 — Inspection dimensions

6

SUPPLIED BY BSB UNDER LICENCE FROM DIN FOR ESCORTS LIMITED - FARIDABAD ON 29/12/2012

3

Key a) Unfavourable position near the tip b) Favourable position near the V circle c) Unfavourable position near the root form circle Figure 4 — Tooth thickness measurement Table 1 — Root fillet radii and deviation factors Dimensions in mm Module m mm

Minimum root fillet radius for chipremoval manufacturing methods

Nominal value for cold-rolling

0,5

0,08

0,27

0,866

0,6

0,10

0,32

0,866

0,75

0,12

0,40

0,866

0,8

0,13

0,43

0,866

1

0,16

0,54

0,866

1,25

0,20

0,67

0,866

1,5

0,24

0,81

0,866

1,75

0,28

0,94

0,866

2

0,32

1,08

0,866

2,5

0,40

1,35

0,866

3

0,48

1,62

0,866

4

0,64

2,16

0,866

5

0,80



0,866

6

0,96



0,866

8

1,28



0,866

10

1,60



0,866

ρ F min

ρF

Deviation factor A *Wk

7

SUPPLIED BY BSB UNDER LICENCE FROM DIN FOR ESCORTS LIMITED - FARIDABAD ON 29/12/2012

DIN 5480-2:2006-05

DIN 5480-2:2006-05

4

Module m = 0,5 mm Table 2 — Nominal dimensions, m = 0,5 mm Dimensions in mm

ReferNumber Pitch ence of teeth diameter diameter

a

8

Base diameter

Hub diameters

Shaft Space width Root addendum Tooth diammodification thickness eter

Shaft diameters

Deviationa

Root form circle diameter dFf2

Tip diameter

Tip diameter

Root form circle Root a diameter diameter Deviation dFf1

dB

z

d

db

x1 ⋅ m

e2 = s1

df2

Adf2

min.

da2

da1

max.

df1

Adf1

6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40

10 12 14 16 18 20 22 24 26 28 30 32 34 36 38 40 42 44 46 48 50 52 54 56 58 60 62 64 66 68 70 72 74 76 78

5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39

4,330 5,196 6,062 6,928 7,794 8,660 9,526 10,392 11,258 12,124 12,990 13,856 14,722 15,588 16,454 17,321 18,187 19,053 19,919 20,785 21,651 22,517 23,383 24,249 25,115 25,981 26,847 27,713 28,579 29,445 30,311 31,177 32,043 32,909 33,775

0,225 0,225 0,225 0,225 0,225 0,225 0,225 0,225 0,225 0,225 0,225 0,225 0,225 0,225 0,225 0,225 0,225 0,225 0,225 0,225 0,225 0,225 0,225 0,225 0,225 0,225 0,225 0,225 0,225 0,225 0,225 0,225 0,225 0,225 0,225

1,045 1,045 1,045 1,045 1,045 1,045 1,045 1,045 1,045 1,045 1,045 1,045 1,045 1,045 1,045 1,045 1,045 1,045 1,045 1,045 1,045 1,045 1,045 1,045 1,045 1,045 1,045 1,045 1,045 1,045 1,045 1,045 1,045 1,045 1,045

6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40

0,19 0,19 0,19 0,19 0,19 0,19 0,19 0,20 0,20 0,20 0,20 0,20 0,20 0,20 0,20 0,20 0,20 0,20 0,20 0,20 0,21 0,21 0,21 0,21 0,21 0,21 0,21 0,21 0,21 0,21 0,21 0,21 0,21 0,21 0,21

5,95 6,95 7,95 8,95 9,95 10,95 11,95 12,96 13,96 14,96 15,96 16,96 17,96 18,96 19,96 20,96 21,96 22,96 23,96 24,96 25,96 26,96 27,96 28,96 29,96 30,96 31,96 32,96 33,96 34,96 35,96 36,96 37,96 38,96 39,96

5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39

5,9 6,9 7,9 8,9 9,9 10,9 11,9 12,9 13,9 14,9 15,9 16,9 17,9 18,9 19,9 20,9 21,9 22,9 23,9 24,9 25,9 26,9 27,9 28,9 29,9 30,9 31,9 32,9 33,9 34,9 35,9 36,9 37,9 38,9 39,9

4,95 5,95 6,95 7,95 8,95 9,95 10,95 11,94 12,94 13,94 14,94 15,94 16,94 17,94 18,94 19,94 20,94 21,94 22,94 23,94 24,94 25,94 26,94 27,94 28,94 29,94 30,94 31,94 32,94 33,94 34,94 35,94 36,94 37,94 38,94

4,90 5,90 6,90 7,90 8,90 9,90 10,90 11,90 12,90 13,90 14,90 15,90 16,90 17,90 18,90 19,90 20,90 21,90 22,90 23,90 24,90 25,90 26,90 27,90 28,90 29,90 30,90 31,90 32,90 33,90 34,90 35,90 36,90 37,90 38,90

–0,41 –0,41 –0,41 –0,41 –0,41 –0,41 –0,41 –0,45 –0,45 –0,45 –0,45 –0,45 –0,45 –0,45 –0,45 –0,45 –0,45 –0,45 –0,45 –0,45 –0,49 –0,49 –0,49 –0,49 –0,49 –0,49 –0,49 –0,49 –0,49 –0,49 –0,49 –0,49 –0,49 –0,49 –0,49

The deviation values given here relate to chip-cutting machining methods and the theoretical root diameter (see DIN 5480-1, 7.1). The deviation for cold-rolled splines is –0,76 ⋅ m.

SUPPLIED BY BSB UNDER LICENCE FROM DIN FOR ESCORTS LIMITED - FARIDABAD ON 29/12/2012

Nominal dimensions

Basic data

DIN 5480-2:2006-05

Table 3 — Inspection dimensions, m = 0,5 mm Dimensions in mm

Reference diameter

a

Hub dimensions

Number Measuring of teeth circle diameter

Shaft dimensions

Nominal dimension

Deviation factor

Measuring circle diameter

Nominal dimension

Deviation factor

Number of teeth measured

Nominal dimension

k

Wk

a

3,859 3,905 3,952 5,359 5,405 5,452 6,859 6,905 6,952 8,359 8,405 8,452 9,859 9,905 9,952 11,359 11,405 11,452 12,859 12,905 12,952 14,359 14,405 14,452 15,859 15,905 15,952 17,359 17,405 17,452 18,859 18,905 18,952 20,359 20,405

dB

z

DM

M2

A *M2

DM

M1

A *M1

6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40

10 12 14 16 18 20 22 24 26 28 30 32 34 36 38 40 42 44 46 48 50 52 54 56 58 60 62 64 66 68 70 72 74 76 78

1,0 1,0 1,0 1,0 1,0 1,0 1,0 1,0 1,0 1,0 1,0 1,0 1,0 1,0 1,0 1,0 1,0 1,0 1,0 1,0 1,0 1,0 1,0 1,0 1,0 1,0 1,0 1,0 1,0 1,0 1,0 1,0 1,0 1,0 1,0

3,797 4,800 5,801 6,803 7,804 8,804 9,805 10,805 11,806 12,806 13,807 14,807 15,807 16,807 17,807 18,808 19,808 20,808 21,808 22,808 23,808 24,808 25,808 26,808 27,808 28,808 29,809 30,809 31,809 32,809 33,809 34,809 35,809 36,809 37,809

2,01 1,95 1,91 1,88 1,86 1,85 1,84 1,83 1,82 1,81 1,80 1,80 1,80 1,79 1,79 1,79 1,78 1,78 1,78 1,78 1,77 1,77 1,77 1,77 1,77 1,77 1,77 1,76 1,76 1,76 1,76 1,76 1,76 1,76 1,76

1,25 1,25 1,25 1,25 1,0 1,0 1,0 1,0 1,0 1,0 1,0 1,0 1,0 1,0 1,0 1,0 1,0 1,0 1,0 1,0 1,0 1,0 1,0 1,0 1,0 1,0 1,0 1,0 1,0 1,0 1,0 1,0 1,0 1,0 1,0

7,511 8,540 9,564 10,584 10,961 11,970 12,978 13,985 14,991 15,996 17,001 18,005 19,009 20,013 21,016 22,019 23,022 24,024 25,026 26,029 27,031 28,033 29,034 30,036 31,038 32,039 33,040 34,042 35,043 36,044 37,045 38,046 39,048 40,048 41,049

1,20 1,23 1,27 1,29 1,39 1,41 1,43 1,44 1,46 1,47 1,48 1,49 1,50 1,51 1,52 1,53 1,54 1,54 1,55 1,55 1,56 1,57 1,57 1,57 1,58 1,58 1,59 1,59 1,59 1,60 1,60 1,60 1,61 1,61 1,61

3 3 3 4 4 4 5 5 5 6 6 6 7 7 7 8 8 8 9 9 9 10 10 10 11 11 11 12 12 12 13 13 13 14 14

a a

a

a

a

a

a

a

a

a

a

a

SUPPLIED BY BSB UNDER LICENCE FROM DIN FOR ESCORTS LIMITED - FARIDABAD ON 29/12/2012

Basic data

These tooth thickness measurements are not reliable because they were made near the root fillet or the edge of the tip. Measurements between and over measuring circles are preferable. Deviations and tolerances can result in the unreliability of other tooth thickness measurements not identified by a.

9

DIN 5480-2:2006-05

5

Module m = 0,6 mm Table 4 — Nominal dimensions, m = 0,6 mm Dimensions in mm

Reference diameter

10

NumPitch ber of diameter teeth

Base diameter

Hub diameter

Shaft Space width Root addendum Tooth diammodification thickness eter

Deviation

Shaft diameter

Root form Tip circle diameter diameter dFf2

Tip diameter

Root form circle Root diameter diameter

Deviation

dFf1

dB

z

d

db

x1 ⋅ m

e2 = s1

df2

Adf2

min.

da2

da1

max.

df1

Adf1

6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 42 45 47 48

8 10 12 13 15 17 18 20 22 23 25 27 28 30 32 34 35 37 38 40 42 44 45 47 48 50 52 54 55 57 58 60 62 64 64 68 74 76 78

4,8 6,0 7,2 7,8 9,0 10,2 10,8 12,0 13,2 13,8 15,0 16,2 16,8 18,0 19,2 20,4 21,0 22,2 22,8 24,0 25,2 26,4 27,0 28,2 28,8 30,0 31,2 32,4 33,0 34,2 34,8 36,0 37,2 38,4 38,4 40,8 44,4 45,6 46,8

4,157 5,196 6,235 6,755 7,794 8,833 9,353 10,392 11,432 11,951 12,990 14,030 14,549 15,588 16,628 17,667 18,187 19,226 19,745 20,785 21,824 22,863 23,383 24,422 24,942 25,981 27,020 28,059 28,579 29,618 30,138 31,177 32,216 33,255 33,255 35,334 38,452 39,491 40,530

0,27 0,17 0,07 0,27 0,17 0,07 0,27 0,17 0,07 0,27 0,17 0,07 0,27 0,17 0,07 –0,03 0,17 0,07 0,27 0,17 0,07 –0,03 0,17 0,07 0,27 0,17 0,07 –0,03 0,17 0,07 0,27 0,17 0,07 –0,03 0,47 0,27 –0,03 0,37 0,27

1,254 1,139 1,023 1,254 1,139 1,023 1,254 1,139 1,023 1,254 1,139 1,023 1,254 1,139 1,023 0,908 1,139 1,023 1,254 1,139 1,023 0,908 1,139 1,023 1,254 1,139 1,023 0,908 1,139 1,023 1,254 1,139 1,023 0,908 1,485 1,254 0,908 1,370 1,254

6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 42 45 47 48

0,21 0,21 0,21 0,21 0,21 0,21 0,21 0,22 0,22 0,22 0,22 0,22 0,22 0,22 0,22 0,22 0,22 0,22 0,22 0,22 0,23 0,23 0,23 0,23 0,23 0,23 0,23 0,23 0,23 0,23 0,23 0,23 0,23 0,23 0,23 0,23 0,23 0,23 0,23

5,93 6,93 7,93 8,93 9,93 10,93 11,93 12,94 13,94 14,94 15,94 16,94 17,94 18,94 19,94 20,94 21,94 22,94 23,94 24,94 25,94 26,94 27,94 28,94 29,94 30,94 31,94 32,94 33,94 34,94 35,94 36,94 37,94 38,94 39,94 41,94 44,94 46,94 47,94

4,8 5,8 6,8 7,8 8,8 9,8 10,8 11,8 12,8 13,8 14,8 15,8 16,8 17,8 18,8 19,8 20,8 21,8 22,8 23,8 24,8 25,8 26,8 27,8 28,8 29,8 30,8 31,8 32,8 33,8 34,8 35,8 36,8 37,8 38,8 40,8 43,8 45,8 46,8

5,88 6,88 7,88 8,88 9,88 10,88 11,88 12,88 13,88 14,88 15,88 16,88 17,88 18,88 19,88 20,88 21,88 22,88 23,88 24,88 25,88 26,88 27,88 28,88 29,88 30,88 31,88 32,88 33,88 34,88 35,88 36,88 37,88 38,88 39,88 41,88 44,88 46,88 47,88

4,75 5,75 6,75 7,75 8,75 9,75 10,75 11,74 12,74 13,74 14,74 15,74 16,74 17,74 18,74 19,74 20,74 21,74 22,74 23,74 24,74 25,74 26,74 27,74 28,74 29,74 30,74 31,74 32,74 33,74 34,74 35,74 36,74 37,74 38,74 40,74 43,74 45,74 46,74

4,68 5,68 6,68 7,68 8,68 9,68 10,68 11,68 12,68 13,68 14,68 15,68 16,68 17,68 18,68 19,68 20,68 21,68 22,68 23,68 24,68 25,68 26,68 27,68 28,68 29,68 30,68 31,68 32,68 33,68 34,68 35,68 36,68 37,68 38,68 40,68 43,68 45,68 46,68

–0,43 –0,43 –0,43 –0,43 –0,43 –0,43 –0,43 –0,47 –0,47 –0,47 –0,47 –0,47 –0,47 –0,47 –0,47 –0,47 –0,47 –0,47 –0,47 –0,47 –0,51 –0,51 –0,51 –0,51 –0,51 –0,51 –0,51 –0,51 –0,51 –0,51 –0,51 –0,51 –0,51 –0,51 –0,51 –0,51 –0,51 –0,51 –0,51

SUPPLIED BY BSB UNDER LICENCE FROM DIN FOR ESCORTS LIMITED - FARIDABAD ON 29/12/2012

Nominal dimensions

Basic data

DIN 5480-2:2006-05

Table 5 — Inspection dimensions, m = 0,6 mm Dimensions in mm Hub dimensions

Reference Number of Measuring diameter teeth circle diameter

a

Shaft dimensions

Nominal dimension

Deviation factor

Measuring circle diameter

Nominal dimension

Deviation factor

Number of teeth measured

Nominal dimension

k

Wk

a

2,942 2,898 4,486 4,714 4,670 6,258 6,486 6,442 6,398 8,258 8,214 8,170 10,030 9,986 9,942 9,898 11,758 11,714 11,942 11,898 13,486 13,442 13,670 15,258 15,486 15,442 15,398 15,354 17,214 17,170 19,030 18,986 18,942 18,898 21,030 20,942 22,442 24,530 24,486

dB

z

DM

M2

A *M2

DM

M1

A *M1

6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 42 45 47 48

8 10 12 13 15 17 18 20 22 23 25 27 28 30 32 34 35 37 38 40 42 44 45 47 48 50 52 54 55 57 58 60 62 64 64 68 74 76 78

1,0 1,0 1,0 1,0 1,0 1,0 1,0 1,0 1,0 1,0 1,0 1,0 1,0 1,0 1,0 1,0 1,0 1,0 1,0 1,0 1,0 1,0 1,0 1,0 1,0 1,0 1,0 1,0 1,0 1,0 1,0 1,0 1,0 1,0 1,0 1,0 1,0 1,0 1,0

3,964 4,972 5,959 6,909 7,923 8,921 9,969 10,972 11,966 12,937 13,943 14,940 15,970 16,972 17,968 18,957 19,951 20,949 21,971 22,972 23,969 24,961 25,956 26,954 27,971 28,972 29,970 30,963 31,959 32,957 33,971 34,972 35,970 36,965 37,960 39,971 42,966 44,968 45,971

1,58 1,76 1,95 1,62 1,74 1,86 1,66 1,74 1,84 1,67 1,74 1,81 1,68 1,74 1,80 1,86 1,74 1,79 1,69 1,74 1,78 1,83 1,74 1,78 1,70 1,74 1,77 1,81 1,74 1,77 1,71 1,74 1,77 1,80 1,66 1,71 1,79 1,69 1,71

1,75 1,5 1,25 1,5 1,25 1,25 1,5 1,25 1,25 1,25 1,25 1,25 1,25 1,25 1,25 1,25 1,25 1,25 1,25 1,25 1,25 1,25 1,25 1,25 1,25 1,25 1,25 1,25 1,25 1,25 1,25 1,25 1,25 1,25 1,25 1,25 1,25 1,25 1,25

8,348 8,874 9,327 10,795 11,250 12,307 13,922 14,333 15,372 16,275 17,319 18,356 19,330 20,365 21,394 22,417 23,353 24,380 25,356 26,384 27,407 28,425 29,374 30,395 31,374 32,396 33,415 34,431 35,387 36,405 37,386 38,405 39,421 40,434 41,353 43,395 46,437 48,385 49,402

1,12 1,22 1,36 1,24 1,36 1,42 1,32 1,43 1,47 1,42 1,46 1,51 1,46 1,50 1,53 1,57 1,52 1,55 1,51 1,54 1,57 1,60 1,56 1,58 1,54 1,57 1,60 1,62 1,58 1,61 1,57 1,59 1,61 1,64 1,55 1,59 1,65 1,59 1,60

2 2 3 3 3 4 4 4 4 5 5 5 6 6 6 6 7 7 7 7 8 8 8 9 9 9 9 9 10 10 11 11 11 11 12 12 13 14 14

a

a a

a a

a a

a a

a

These tooth thickness measurements are not reliable because they were made near the root fillet or the edge of the tip. Measurements between and over measuring circles are preferable. Deviations and tolerances can result in the unreliability of other tooth thickness measurements not identified by a.

11

SUPPLIED BY BSB UNDER LICENCE FROM DIN FOR ESCORTS LIMITED - FARIDABAD ON 29/12/2012

Basic data

DIN 5480-2:2006-05

6

Module m = 0,75 mm Table 6 — Nominal dimensions, m = 0,75 mm Dimensions in mm

Refer- Number of ence diameter teeth

Pitch diameter

Base diameter

Shaft Space addenwidth dum Tooth modificathickness tion

Hub diameter Root diameter

Root form circle Deviation diameter

dFf2

Shaft diameter Tip diameter

Tip diameter

Root form circle Root diameter diameter dFf1

Deviation

dB

z

d

db

x1 ⋅ m

e2 = s1

df2

Adf2

min.

da2

da1

max.

df1

Adf1

6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 42 45 47 48 50 52 55

6 8 9 10 12 13 14 16 17 18 20 21 22 24 25 26 28 29 30 32 33 34 36 37 38 40 41 42 44 45 46 48 49 50 52 54 58 60 62 64 68 72

4,50 6,00 6,75 7,50 9,00 9,75 10,50 12,00 12,75 13,50 15,00 15,75 16,50 18,00 18,75 19,50 21,00 21,75 22,50 24,00 24,75 25,50 27,00 27,75 28,50 30,00 30,75 31,50 33,00 33,75 34,50 36,00 36,75 37,50 39,00 40,50 43,50 45,00 46,50 48,00 51,00 54,00

3,897 5,196 5,846 6,495 7,794 8,444 9,093 10,392 11,042 11,691 12,990 13,640 14,289 15,588 16,238 16,887 18,187 18,836 19,486 20,785 21,434 22,084 23,383 24,032 24,682 25,981 26,630 27,280 28,579 29,228 29,878 31,177 31,826 32,476 33,775 35,074 37,672 38,971 40,270 41,569 44,167 46,765

0,3375 0,0875 0,2125 0,3375 0,0875 0,2125 0,3375 0,0875 0,2125 0,3375 0,0875 0,2125 0,3375 0,0875 0,2125 0,3375 0,0875 0,2125 0,3375 0,0875 0,2125 0,3375 0,0875 0,2125 0,3375 0,0875 0,2125 0,3375 0,0875 0,2125 0,3375 0,0875 0,2125 0,3375 0,0875 0,3375 0,3375 0,5875 0,3375 0,5875 0,0875 0,0875

1,568 1,279 1,423 1,568 1,279 1,423 1,568 1,279 1,423 1,568 1,279 1,423 1,568 1,279 1,423 1,568 1,279 1,423 1,568 1,279 1,423 1,568 1,279 1,423 1,568 1,279 1,423 1,568 1,279 1,423 1,568 1,279 1,423 1,568 1,279 1,568 1,568 1,856 1,568 1,856 1,279 1,279

6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 42 45 47 48 50 52 55

0,24 0,24 0,24 0,24 0,24 0,24 0,24 0,25 0,25 0,25 0,25 0,25 0,25 0,25 0,25 0,25 0,25 0,25 0,25 0,25 0,26 0,26 0,26 0,26 0,26 0,26 0,26 0,26 0,26 0,26 0,26 0,26 0,26 0,26 0,26 0,26 0,26 0,26 0,26 0,26 0,27 0,27

5,90 6,90 7,90 8,90 9,90 10,90 11,90 12,91 13,91 14,91 15,91 16,91 17,91 18,91 19,91 20,91 21,91 22,91 23,91 24,91 25,91 26,91 27,91 28,91 29,91 30,91 31,91 32,91 33,91 34,91 35,91 36,91 37,91 38,91 39,91 41,91 44,91 46,91 47,91 49,91 51,92 54,92

4,5 5,5 6,5 7,5 8,5 9,5 10,5 11,5 12,5 13,5 14,5 15,5 16,5 17,5 18,5 19,5 20,5 21,5 22,5 23,5 24,5 25,5 26,5 27,5 28,5 29,5 30,5 31,5 32,5 33,5 34,5 35,5 36,5 37,5 38,5 40,5 43,5 45,5 46,5 48,5 50,5 53,5

5,85 6,85 7,85 8,85 9,85 10,85 11,85 12,85 13,85 14,85 15,85 16,85 17,85 18,85 19,85 20,85 21,85 22,85 23,85 24,85 25,85 26,85 27,85 28,85 29,85 30,85 31,85 32,85 33,85 34,85 35,85 36,85 37,85 38,85 39,85 41,85 44,85 46,85 47,85 49,85 51,85 54,85

4,45 5,45 6,45 7,45 8,45 9,45 10,45 11,44 12,44 13,44 14,44 15,44 16,44 17,44 18,44 19,44 20,44 21,44 22,44 23,44 24,44 25,44 26,44 27,44 28,44 29,44 30,44 31,44 32,44 33,44 34,44 35,44 36,44 37,44 38,44 40,44 43,44 45,44 46,44 48,44 50,43 53,43

4,35 5,35 6,35 7,35 8,35 9,35 10,35 11,35 12,35 13,35 14,35 15,35 16,35 17,35 18,35 19,35 20,35 21,35 22,35 23,35 24,35 25,35 26,35 27,35 28,35 29,35 30,35 31,35 32,35 33,35 34,35 35,35 36,35 37,35 38,35 40,35 43,35 45,35 46,35 48,35 50,35 53,35

–0,46 –0,46 –0,46 –0,46 –0,46 –0,46 –0,46 –0,50 –0,50 –0,50 –0,50 –0,50 –0,50 –0,50 –0,50 –0,50 –0,50 –0,50 –0,50 –0,50 –0,54 –0,54 –0,54 –0,54 –0,54 –0,54 –0,54 –0,54 –0,54 –0,54 –0,54 –0,54 –0,54 –0,54 –0,54 –0,54 –0,54 –0,54 –0,54 –0,54 –0,58 –0,58

12

SUPPLIED BY BSB UNDER LICENCE FROM DIN FOR ESCORTS LIMITED - FARIDABAD ON 29/12/2012

Nominal dimensions

Basic data

DIN 5480-2:2006-05

Table 7 — Inspection dimensions, m = 0,75 mm Dimensions in mm Hub dimensions

Reference Number of Measuring diameter teeth circle diameter

a

Shaft dimensions

Nominal dimension

Deviation factor

Measuring circle diameter

Nominal dimension

Deviation factor

Number of teeth measured

Nominal dimension

Wk

dB

z

DM

M2

A *M2

DM

M1

A *M1

k

6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 42 45 47 48 50 52 55

6 8 9 10 12 13 14 16 17 18 20 21 22 24 25 26 28 29 30 32 33 34 36 37 38 40 41 42 44 45 46 48 49 50 52 54 58 60 62 64 68 72

1,5 1,25 1,25 1,5 1,25 1,25 1,5 1,25 1,25 1,25 1,25 1,25 1,5 1,25 1,25 1,50 1,25 1,25 1,25 1,25 1,25 1,25 1,25 1,25 1,25 1,25 1,25 1,25 1,25 1,25 1,25 1,25 1,25 1,25 1,25 1,25 1,25 1,25 1,25 1,25 1,25 1,25

2,673 4,438 5,363 5,695 7,449 8,395 8,702 10,454 11,411 12,461 13,457 14,421 14,707 16,458 17,428 17,709 19,459 20,434 21,463 22,460 23,437 24,463 25,461 26,440 27,463 28,461 29,443 30,463 31,462 32,445 33,464 34,462 35,447 36,464 37,462 39,464 42,464 44,450 45,464 47,451 49,463 52,463

2,42 2,13 1,73 2,01 1,95 1,74 1,91 1,88 1,74 1,66 1,85 1,74 1,84 1,83 1,74 1,82 1,81 1,74 1,69 1,80 1,74 1,69 1,79 1,74 1,69 1,79 1,74 1,70 1,78 1,74 1,70 1,78 1,74 1,70 1,77 1,71 1,71 1,66 1,71 1,66 1,76 1,76

2,75 1,75 1,75 2,0 1,5 1,5 1,75 1,5 1,5 1,5 1,5 1,5 1,5 1,5 1,5 1,5 1,5 1,5 1,5 1,5 1,5 1,5 1,5 1,5 1,5 1,5 1,5 1,5 1,5 1,5 1,5 1,5 1,5 1,5 1,5 1,5 1,5 1,5 1,5 1,5 1,5 1,5

10,087 9,072 9,894 11,564 11,497 12,374 14,037 14,522 15,424 16,442 17,539 18,457 19,467 20,552 21,481 22,486 23,561 24,499 25,501 26,569 27,513 28,514 29,575 30,524 31,524 32,580 33,534 34,532 35,584 36,542 37,540 38,588 39,549 40,546 41,591 43,552 46,556 48,510 49,561 51,517 53,600 56,602

1,02 1,23 1,21 1,18 1,38 1,35 1,29 1,44 1,41 1,39 1,48 1,45 1,43 1,51 1,48 1,46 1,53 1,50 1,48 1,55 1,52 1,50 1,56 1,54 1,52 1,58 1,55 1,54 1,59 1,57 1,55 1,60 1,58 1,56 1,61 1,57 1,58 1,55 1,59 1,56 1,63 1,64

2 2 2 3 3 3 3 3 4 4 4 4 5 5 5 5 5 6 6 6 6 7 7 7 7 7 8 8 8 8 9 9 9 9 9 10 11 11 11 12 12 13

a a

a

a

a a

a

a a

a

a a

a a

3,608 3,428 3,588 5,788 5,608 5,768 5,928 5,747 7,948 8,108 7,928 8,088 10,288 10,108 10,268 10,428 10,247 12,448 12,608 12,428 12,588 14,788 14,608 14,768 14,928 14,747 16,948 17,108 16,928 17,088 19,288 19,108 19,268 19,428 19,247 21,608 23,788 24,108 23,928 26,288 25,928 28,108

These tooth thickness measurements are not reliable because they were made near the root fillet or the edge of the tip. Measurements between and over measuring circles are preferable. Deviations and tolerances can result in the unreliability of other tooth thickness measurements not identified by a.

13

SUPPLIED BY BSB UNDER LICENCE FROM DIN FOR ESCORTS LIMITED - FARIDABAD ON 29/12/2012

Basic data

DIN 5480-2:2006-05

7

Module m = 0,8 mm Table 8 — Nominal dimensions, m = 0,8 mm Dimensions in mm

Reference diameter

Number of teeth

Pitch diameter

Base diameter

dB

z

d

db

x1 ⋅ m

6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 42 45 47 48 50 52 55 58 60

6 7 8 10 11 12 13 15 16 17 18 20 21 22 23 24 25 26 27 28 30 31 32 34 35 36 37 38 40 41 42 44 45 46 47 48 51 55 57 58 60 64 66 70 74

4,8 5,6 6,4 8,0 8,8 9,6 10,4 12,0 12,8 13,6 14,4 16,0 16,8 17,6 18,4 19,2 20,0 20,8 21,6 22,4 24,0 24,8 25,6 27,2 28,0 28,8 29,6 30,4 32,0 32,8 33,6 35,2 36,0 36,8 37,6 38,4 40,8 44,0 45,6 46,4 48,0 51,2 52,8 56,0 59,2

4,157 4,850 5,543 6,928 7,621 8,314 9,007 10,392 11,085 11,778 12,471 13,856 14,549 15,242 15,935 16,628 17,321 18,013 18,706 19,399 20,785 21,477 22,170 23,556 24,249 24,942 25,634 26,327 27,713 28,406 29,098 30,484 31,177 31,870 32,563 33,255 35,334 38,105 39,491 40,184 41,569 44,341 45,726 48,497 51,269

0,16 0,26 0,36 0,06 0,16 0,26 0,36 0,06 0,16 0,26 0,36 0,06 0,16 0,26 0,36 –0,04 0,06 0,16 0,26 0,36 0,06 0,16 0,26 –0,04 0,06 0,16 0,26 0,36 0,06 0,16 0,26 –0,04 0,06 0,16 0,26 0,36 0,16 0,06 0,26 0,36 0,56 –0,04 0,66 0,56 –0,04

14

Shaft Space width addendum Tooth modification thickness

Hub diameter Root form circle diameter

Root diameter

Deviation

e2 = s1

df2

Adf2

dFf2 min.

1,441 1,557 1,672 1,326 1,441 1,557 1,672 1,326 1,441 1,557 1,672 1,326 1,441 1,557 1,672 1,210 1,326 1,441 1,557 1,672 1,326 1,441 1,557 1,210 1,326 1,441 1,557 1,672 1,326 1,441 1,557 1,210 1,326 1,441 1,557 1,672 1,441 1,326 1,557 1,672 1,903 1,210 2,019 1,903 1,210

6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 42 45 47 48 50 52 55 58 60

0,25 0,25 0,25 0,25 0,25 0,25 0,25 0,26 0,26 0,26 0,26 0,26 0,26 0,26 0,26 0,26 0,26 0,26 0,26 0,26 0,26 0,27 0,27 0,27 0,27 0,27 0,27 0,27 0,27 0,27 0,27 0,27 0,27 0,27 0,27 0,27 0,27 0,27 0,27 0,27 0,27 0,28 0,28 0,28 0,28

5,89 6,89 7,89 8,89 9,89 10,89 11,89 12,90 13,90 14,90 15,90 16,90 17,90 18,90 19,90 19,90 20,90 21,90 22,90 23,90 24,90 25,90 26,90 27,90 28,90 29,90 30,90 31,90 32,90 33,90 34,90 35,90 36,90 37,90 38,90 39,90 41,90 44,90 46,90 47,90 49,90 51,91 54,91 57,91 59,91

Shaft diameter Root form circle diameter

Tip diameter

Tip diameter

da2

da1

dFf1 max.

4,4 5,4 6,4 7,4 8,4 9,4 10,4 11,4 12,4 13,4 14,4 15,4 16,4 17,4 18,4 18,4 19,4 20,4 21,4 22,4 23,4 24,4 25,4 26,4 27,4 28,4 29,4 30,4 31,4 32,4 33,4 34,4 35,4 36,4 37,4 38,4 40,4 43,4 45,4 46,4 48,4 50,4 53,4 56,4 58,4

5,84 6,84 7,84 8,84 9,84 10,84 11,84 12,84 13,84 14,84 15,84 16,84 17,84 18,84 19,84 19,84 20,84 21,84 22,84 23,84 24,84 25,84 26,84 27,84 28,84 29,84 30,84 31,84 32,84 33,84 34,84 35,84 36,84 37,84 38,84 39,84 41,84 44,84 46,84 47,84 49,84 51,84 54,84 57,84 59,84

4,35 5,35 6,35 7,35 8,35 9,35 10,35 11,34 12,34 13,34 14,34 15,34 16,34 17,34 18,34 18,34 19,34 20,34 21,34 22,34 23,34 24,34 25,34 26,34 27,34 28,34 29,34 30,34 31,34 32,34 33,34 34,34 35,34 36,34 37,34 38,34 40,34 43,34 45,34 46,34 48,34 50,33 53,33 56,33 58,33

Root diameter

Deviation

df1

Adf1

4,24 5,24 6,24 7,24 8,24 9,24 10,24 11,24 12,24 13,24 14,24 15,24 16,24 17,24 18,24 18,24 19,24 20,24 21,24 22,24 23,24 24,24 25,24 26,24 27,24 28,24 29,24 30,24 31,24 32,24 33,24 34,24 35,24 36,24 37,24 38,24 40,24 43,24 45,24 46,24 48,24 50,24 53,24 56,24 58,24

–0,47 –0,47 –0,47 –0,47 –0,47 –0,47 –0,47 –0,51 –0,51 –0,51 –0,51 –0,51 –0,51 –0,51 –0,51 –0,51 –0,51 –0,51 –0,51 –0,51 –0,51 –0,55 –0,55 –0,55 –0,55 –0,55 –0,55 –0,55 –0,55 –0,55 –0,55 –0,55 –0,55 –0,55 –0,55 –0,55 –0,55 –0,55 –0,55 –0,55 –0,55 –0,59 –0,59 –0,59 –0,59

SUPPLIED BY BSB UNDER LICENCE FROM DIN FOR ESCORTS LIMITED - FARIDABAD ON 29/12/2012

Nominal dimensions

Basic data

DIN 5480-2:2006-05

Table 9 — Inspection dimensions, m = 0,8 mm Dimensions in mm Hub dimensions

Shaft dimensions

Reference diameter

Number of teeth

Measuring circle diameter

Nominal dimension

Deviation factor

Measuring circle diameter

dB

z

DM

M2

A *M2

DM

M1

A *M1

6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 42 45 47 48 50 52 55 58 60

6 7 8 10 11 12 13 15 16 17 18 20 21 22 23 24 25 26 27 28 30 31 32 34 35 36 37 38 40 41 42 44 45 46 47 48 51 55 57 58 60 64 66 70 74

1,4 1,5 1,5 1,4 1,5 1,5 1,5 1,5 1,5 1,5 1,5 1,5 1,5 1,5 1,5 1,5 1,5 1,5 1,5 1,5 1,5 1,5 1,5 1,5 1,5 1,5 1,5 1,5 1,5 1,5 1,5 1,5 1,5 1,5 1,5 1,5 1,5 1,5 1,5 1,5 1,5 1,5 1,5 1,5 1,5

3,052 3,629 4,794 6,023 6,649 7,779 8,720 9,643 10,759 11,728 12,795 13,736 14,724 15,788 16,753 16,711 17,713 18,776 19,754 20,796 21,760 22,748 23,791 24,742 25,739 26,782 27,765 28,796 29,770 30,760 31,792 32,756 33,752 34,785 35,772 36,796 38,768 41,761 43,776 44,796 46,794 48,770 51,790 54,794 56,774

2,42 2,18 1,83 2,41 2,27 1,95 1,77 2,30 2,03 1,86 1,77 2,08 1,93 1,84 1,76 2,12 1,98 1,89 1,81 1,76 1,93 1,85 1,80 1,96 1,89 1,84 1,79 1,75 1,87 1,82 1,78 1,90 1,85 1,81 1,78 1,75 1,80 1,83 1,77 1,74 1,70 1,84 1,69 1,71 1,82

2,25 2,25 2,25 1,75 1,75 1,75 2,0 1,5 1,75 1,75 1,75 1,5 1,5 1,5 1,75 1,5 1,5 1,5 1,5 1,5 1,5 1,5 1,5 1,5 1,5 1,5 1,5 1,5 1,5 1,5 1,5 1,5 1,5 1,5 1,5 1,5 1,5 1,5 1,5 1,5 1,5 1,5 1,5 1,5 1,5

8,998 9,776 10,939 10,974 11,835 12,903 14,393 14,291 15,992 16,895 17,926 18,378 19,305 20,330 21,920 21,407 22,348 23,369 24,308 25,323 26,397 27,345 28,359 29,417 30,373 31,386 32,340 33,349 34,407 35,367 36,376 37,422 38,388 39,397 40,360 41,365 43,381 46,398 48,374 49,377 51,345 53,428 56,334 59,357 61,430

1,10 1,09 1,12 1,31 1,29 1,30 1,24 1,46 1,38 1,36 1,36 1,52 1,49 1,47 1,40 1,58 1,55 1,53 1,51 1,49 1,57 1,55 1,53 1,61 1,59 1,57 1,55 1,54 1,61 1,59 1,57 1,64 1,62 1,60 1,58 1,57 1,61 1,64 1,61 1,59 1,57 1,66 1,57 1,59 1,67

a

Nominal dimension

Deviation factor

Number of teeth measured

Nominal dimension

k

Wk

2 2 2 2 3 3 3 3 3 4 4 4 4 5 5 4 5 5 5 6 6 6 6 6 6 7 7 7 7 8 8 8 8 8 9 9 9 10 10 11 11 11 12 13 13

a a

a

a a

a

a

a a

a

a

a

3,648 3,786 3,923 3,697 6,011 6,148 6,286 6,060 6,197 8,511 8,648 8,423 8,560 10,874 11,011 8,472 10,786 10,923 11,060 13,374 13,148 13,286 13,423 13,197 13,334 15,648 15,786 15,923 15,697 18,011 18,148 17,923 18,060 18,197 20,511 20,648 20,560 22,786 23,060 25,374 25,648 25,197 28,148 30,374 29,923

These tooth thickness measurements are not reliable because they were made near the root fillet or the edge of the tip. Measurements between and over measuring circles are preferable. Deviations and tolerances can result in the unreliability of other tooth thickness measurements not identified by a.

15

SUPPLIED BY BSB UNDER LICENCE FROM DIN FOR ESCORTS LIMITED - FARIDABAD ON 29/12/2012

Basic data

DIN 5480-2:2006-05

8

Module m = 1 mm Table 10 — Nominal dimensions, m = 1 mm Dimensions in mm

Reference diameter

Number of teeth

Pitch diameter

Base diameter

dB

z

d

db

x1 ⋅ m

8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 42 45 47 48 50 52 55 58 60

6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 22 22 24 24 26 26 28 28 30 30 32 32 34 34 36 36 38 38 40 44 46 46 48 50 54 56 58

6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 22 22 24 24 26 26 28 28 30 30 32 32 34 34 36 36 38 38 40 44 46 46 48 50 54 56 58

5,196 6,062 6,928 7,794 8,660 9,526 10,392 11,258 12,124 12,990 13,856 14,722 15,588 16,454 17,321 19,053 19,053 20,785 20,785 22,517 22,517 24,249 24,249 25,981 25,981 27,713 27,713 29,445 29,445 31,177 31,177 32,909 32,909 34,641 38,105 39,837 39,837 41,569 43,301 46,765 48,497 50,229

0,45 0,45 0,45 0,45 0,45 0,45 0,45 0,45 0,45 0,45 0,45 0,45 0,45 0,45 0,45 –0,05 0,45 –0,05 0,45 –0,05 0,45 –0,05 0,45 –0,05 0,45 –0,05 0,45 –0,05 0,45 –0,05 0,45 –0,05 0,45 0,45 –0,05 –0,05 0,45 0,45 0,45 –0,05 0,45 0,45

16

Hub diameter Root diameter

Deviation

Root form circle diameter

e2 = s1

df2

Adf2

2,090 2,090 2,090 2,090 2,090 2,090 2,090 2,090 2,090 2,090 2,090 2,090 2,090 2,090 2,090 1,513 2,090 1,513 2,090 1,513 2,090 1,513 2,090 1,513 2,090 1,513 2,090 1,513 2,090 1,513 2,090 1,513 2,090 2,090 1,513 1,513 2,090 2,090 2,090 1,513 2,090 2,090

8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 42 45 47 48 50 52 55 58 60

0,29 0,29 0,29 0,29 0,29 0,30 0,30 0,30 0,30 0,30 0,30 0,30 0,30 0,30 0,30 0,30 0,30 0,30 0,31 0,31 0,31 0,31 0,31 0,31 0,31 0,31 0,31 0,31 0,31 0,31 0,31 0,31 0,31 0,31 0,31 0,31 0,31 0,31 0,32 0,32 0,32 0,32

Shaft Space width addendum Tooth modification thickness

Shaft diameter Tip diameter

Tip diameter

Root form circle diameter

min.

da2

da1

7,85 8,85 9,85 10,85 11,85 12,86 13,86 14,86 15,86 16,86 17,86 18,86 19,86 20,86 21,86 22,86 23,86 24,86 25,86 26,86 27,86 28,86 29,86 30,86 31,86 32,86 33,86 34,86 35,86 36,86 37,86 38,86 39,86 41,86 44,86 46,86 47,86 49,86 51,87 54,87 57,87 59,87

6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 40 43 45 46 48 50 53 56 58

7,8 8,8 9,8 10,8 11,8 12,8 13,8 14,8 15,8 16,8 17,8 18,8 19,8 20,8 21,8 22,8 23,8 24,8 25,8 26,8 27,8 28,8 29,8 30,8 31,8 32,8 33,8 34,8 35,8 36,8 37,8 38,8 39,8 41,8 44,8 46,8 47,8 49,8 51,8 54,8 57,8 59,8

dFf2

Root diameter

Deviation

max.

df1

Adf1

5,95 6,95 7,95 8,95 9,95 10,94 11,94 12,94 13,94 14,94 15,94 16,94 17,94 18,94 19,94 20,94 21,94 22,94 23,94 24,94 25,94 26,94 27,94 28,94 29,94 30,94 31,94 32,94 33,94 34,94 35,94 36,94 37,94 39,94 42,94 44,94 45,94 47,94 49,93 52,93 55,93 57,93

5,80 6,80 7,80 8,80 9,80 10,80 11,80 12,80 13,80 14,80 15,80 16,80 17,80 18,80 19,80 20,80 21,80 22,80 23,80 24,80 25,80 26,80 27,80 28,80 29,80 30,80 31,80 32,80 33,80 34,80 35,80 36,80 37,80 39,80 42,80 44,80 45,80 47,80 49,80 52,80 55,80 57,80

–0,51 –0,51 –0,51 –0,51 –0,51 –0,55 –0,55 –0,55 –0,55 –0,55 –0,55 –0,55 –0,55 –0,55 –0,55 –0,55 –0,55 –0,55 –0,59 –0,59 –0,59 –0,59 –0,59 –0,59 –0,59 –0,59 –0,59 –0,59 –0,59 –0,59 –0,59 –0,59 –0,59 –0,59 –0,59 –0,59 –0,59 –0,59 –0,63 –0,63 –0,63 –0,63

dFf1

SUPPLIED BY BSB UNDER LICENCE FROM DIN FOR ESCORTS LIMITED - FARIDABAD ON 29/12/2012

Nominal dimensions

Basic data

DIN 5480-2:2006-05

Table 11 — Inspection dimensions, m = 1 mm Dimensions in mm Hub dimensions

Shaft dimensions

Reference diameter

Number of teeth

Measuring circle diameter

Nominal dimension

dB

z

DM

M2

A *M2

DM

8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 42 45 47 48 50 52 55 58 60

6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 22 22 24 24 26 26 28 28 30 30 32 32 34 34 36 36 38 38 40 44 46 46 48 50 54 56 58

1,75 1,75 1,75 2,0 1,75 2,0 1,75 1,75 1,75 1,75 1,75 1,75 1,75 1,75 1,75 1,5 1,75 1,75 1,75 1,5 1,75 1,75 1,75 1,75 1,75 1,75 1,75 1,75 1,75 1,75 1,75 1,75 1,75 1,75 1,75 1,75 1,75 1,75 1,75 1,75 1,75 1,75

4,367 5,189 6,368 6,459 8,369 8,489 10,369 11,273 12,369 13,286 14,369 15,296 16,370 17,304 18,370 20,110 20,370 21,311 22,370 24,112 24,370 25,321 26,370 27,325 28,370 29,328 30,370 31,331 32,370 33,334 34,370 35,336 36,370 38,370 41,341 43,343 44,370 46,370 48,370 51,347 54,370 56,370

1,64 1,61 1,66 2,03 1,67 1,96 1,68 1,67 1,69 1,68 1,69 1,69 1,70 1,69 1,70 1,84 1,70 2,00 1,71 1,82 1,71 1,95 1,71 1,93 1,71 1,91 1,71 1,90 1,71 1,89 1,72 1,88 1,72 1,72 1,85 1,85 1,72 1,72 1,72 1,83 1,72 1,72

4,0 3,25 3,0 2,75 2,75 2,5 2,5 2,5 2,5 2,25 2,25 2,25 2,25 2,25 2,25 2,25 2,25 2,0 2,25 2,0 2,0 2,0 2,0 2,0 2,0 2,0 2,0 2,0 2,0 2,0 2,0 2,0 2,0 2,0 2,0 2,0 2,0 2,0 2,0 2,0 2,0 2,0

a

Deviation factor

Number of teeth measured

Nominal dimension

M1

A *M1

k

Wk

14,173 13,347 14,103 14,395 15,615 15,915 17,081 17,992 19,128 19,431 20,541 21,473 22,568 23,508 24,592 25,787 26,613 27,109 28,631 29,113 29,982 31,117 31,992 33,121 34,002 35,124 36,010 37,127 38,018 39,129 40,025 41,132 42,032 44,038 47,137 49,139 50,053 52,057 54,061 57,144 60,072 62,075

1,01 1,04 1,11 1,13 1,17 1,21 1,23 1,24 1,27 1,31 1,33 1,33 1,35 1,36 1,37 1,47 1,39 1,54 1,41 1,55 1,46 1,56 1,47 1,57 1,48 1,58 1,49 1,59 1,50 1,59 1,51 1,60 1,52 1,53 1,62 1,62 1,55 1,55 1,56 1,63 1,57 1,58

Deviation Measuring Nominal factor circle diameter dimension

2 2 2 2 3 3 3 3 3 3 4 4 4 4 4 4 5 4 5 5 5 5 6 5 6 6 6 6 7 6 7 7 7 8 8 8 9 9 9 9 10 11

a a a

a a a

a

a

a

a

a

a

a

a a a

4,810 4,857 4,903 4,950 7,717 7,764 7,810 7,857 7,903 7,950 10,717 10,764 10,810 10,857 10,903 10,497 13,717 10,590 13,810 13,403 13,903 13,497 16,717 13,590 16,810 16,403 16,903 16,497 19,717 16,590 19,810 19,403 19,903 22,717 22,403 22,497 25,717 25,810 25,903 25,590 28,903 31,717

These tooth thickness measurements are not reliable because they were made near the root fillet or the edge of the tip. Measurements between and over measuring circles are preferable. Deviations and tolerances can result in the unreliability of other tooth thickness measurements not identified by a.

17

SUPPLIED BY BSB UNDER LICENCE FROM DIN FOR ESCORTS LIMITED - FARIDABAD ON 29/12/2012

Basic data

DIN 5480-2:2006-05

9

Module m = 1,25 mm Table 12 — Nominal dimensions, m = 1,25 mm Dimensions in mm

Refer- Numence ber of diameter teeth

Pitch diameter

Base diameter

Hub diameter

Shaft Space width Root Deviaaddendum Tooth diameter tion modification thickness

Root form circle diameter

dFf2

Shaft diameter Tip diameter

Tip diameter

Root form circle Root diameter diameter Deviation

dFf1

dB

z

d

db

x1 ⋅ m

e2 = s1

df2

Adf2

min.

da2

da1

max.

df1

Adf1

10 11 12 13 14 15 16 17 18 20 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 42 45 47 48 50 52 55 58 60 62 65 68 70 72 75 78 80

6 7 8 9 10 10 11 12 13 14 14 15 16 17 18 18 19 20 21 22 22 23 24 25 26 26 27 28 29 30 30 32 34 36 37 38 40 42 45 46 48 50 53 54 56 58 60 62

7,50 8,75 10,00 11,25 12,50 12,50 13,75 15,00 16,25 17,50 17,50 18,75 20,00 21,25 22,50 22,50 23,75 25,00 26,25 27,50 27,50 28,75 30,00 31,25 32,50 32,50 33,75 35,00 36,25 37,50 37,50 40,00 42,50 45,00 46,25 47,50 50,00 52,50 56,25 57,50 60,00 62,50 66,25 67,50 70,00 72,50 75,00 77,50

6,495 7,578 8,660 9,743 10,825 10,825 11,908 12,990 14,073 15,155 15,155 16,238 17,321 18,403 19,486 19,486 20,568 21,651 22,733 23,816 23,816 24,898 25,981 27,063 28,146 28,146 29,228 30,311 31,393 32,476 32,476 34,641 36,806 38,971 40,054 41,136 43,301 45,466 48,714 49,796 51,962 54,127 57,374 58,457 60,622 62,787 64,952 67,117

0,5625 0,4375 0,3125 0,1875 0,0625 0,5625 0,4375 0,3125 0,1875 0,5625 0,5625 0,4375 0,3125 0,1875 0,0625 0,5625 0,4375 0,3125 0,1875 0,0625 0,5625 0,4375 0,3125 0,1875 0,0625 0,5625 0,4375 0,3125 0,1875 0,0625 0,5625 0,3125 0,5625 0,3125 0,1875 0,5625 0,3125 0,5625 0,1875 0,5625 0,3125 0,5625 0,1875 0,5625 0,3125 0,5625 0,8125 0,5625

2,613 2,469 2,324 2,180 2,036 2,613 2,469 2,324 2,180 2,613 2,613 2,469 2,324 2,180 2,036 2,613 2,469 2,324 2,180 2,036 2,613 2,469 2,324 2,180 2,036 2,613 2,469 2,324 2,180 2,036 2,613 2,324 2,613 2,324 2,180 2,613 2,324 2,613 2,180 2,613 2,324 2,613 2,180 2,613 2,324 2,613 2,902 2,613

10 11 12 13 14 15 16 17 18 20 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 42 45 47 48 50 52 55 58 60 62 65 68 70 72 75 78 80

0,34 0,34 0,34 0,35 0,35 0,35 0,35 0,35 0,35 0,35 0,35 0,35 0,35 0,35 0,35 0,35 0,36 0,36 0,36 0,36 0,36 0,36 0,36 0,36 0,36 0,36 0,36 0,36 0,36 0,36 0,36 0,36 0,36 0,36 0,36 0,36 0,37 0,37 0,37 0,37 0,37 0,37 0,37 0,37 0,37 0,37 0,37 0,37

9,80 10,80 11,80 12,81 13,81 14,81 15,81 16,81 17,81 19,81 19,81 20,81 21,81 22,81 23,81 24,81 25,81 26,81 27,81 28,81 29,81 30,81 31,81 32,81 33,81 34,81 35,81 36,81 37,81 38,81 39,81 41,81 44,81 46,81 47,81 49,81 51,82 54,82 57,82 59,82 61,82 64,82 67,82 69,82 71,82 74,82 77,82 79,82

7,5 8,5 9,5 10,5 11,5 12,5 13,5 14,5 15,5 17,5 17,5 18,5 19,5 20,5 21,5 22,5 23,5 24,5 25,5 26,5 27,5 28,5 29,5 30,5 31,5 32,5 33,5 34,5 35,5 36,5 37,5 39,5 42,5 44,5 45,5 47,5 49,5 52,5 55,5 57,5 59,5 62,5 65,5 67,5 69,5 72,5 75,5 77,5

9,75 10,75 11,75 12,75 13,75 14,75 15,75 16,75 17,75 19,75 19,75 20,75 21,75 22,75 23,75 24,75 25,75 26,75 27,75 28,75 29,75 30,75 31,75 32,75 33,75 34,75 35,75 36,75 37,75 38,75 39,75 41,75 44,75 46,75 47,75 49,75 51,75 54,75 57,75 59,75 61,75 64,75 67,75 69,75 71,75 74,75 77,75 79,75

7,45 8,45 9,45 10,44 11,44 12,44 13,44 14,44 15,44 17,44 17,44 18,44 19,44 20,44 21,44 22,44 23,44 24,44 25,44 26,44 27,44 28,44 29,44 30,44 31,44 32,44 33,44 34,44 35,44 36,44 37,44 39,44 42,44 44,44 45,44 47,44 49,43 52,43 55,43 57,43 59,43 62,43 65,43 67,43 69,43 72,43 75,43 77,43

7,25 8,25 9,25 10,25 11,25 12,25 13,25 14,25 15,25 17,25 17,25 18,25 19,25 20,25 21,25 22,25 23,25 24,25 25,25 26,25 27,25 28,25 29,25 30,25 31,25 32,25 33,25 34,25 35,25 36,25 37,25 39,25 42,25 44,25 45,25 47,25 49,25 52,25 55,25 57,25 59,25 62,25 65,25 67,25 69,25 72,25 75,25 77,25

–0,56 –0,56 –0,56 –0,60 –0,60 –0,60 –0,60 –0,60 –0,60 –0,60 –0,60 –0,60 –0,60 –0,60 –0,60 –0,60 –0,64 –0,64 –0,64 –0,64 –0,64 –0,64 –0,64 –0,64 –0,64 –0,64 –0,64 –0,64 –0,64 –0,64 –0,64 –0,64 –0,64 –0,64 –0,64 –0,64 –0,68 –0,68 –0,68 –0,68 –0,68 –0,68 –0,68 –0,68 –0,68 –0,68 –0,68 –0,68

18

SUPPLIED BY BSB UNDER LICENCE FROM DIN FOR ESCORTS LIMITED - FARIDABAD ON 29/12/2012

Nominal dimensions

Basic data

DIN 5480-2:2006-05

Table 13 — Inspection dimensions, m = 1,25 mm Dimensions in mm Hub dimensions

Reference Number of Measuring diameter teeth circle diameter

a

Shaft dimensions

Nominal dimension

Deviation factor

Measuring circle diameter

Nominal dimension

Deviation factor

Number of teeth measured

Nominal dimension

k

Wk

dB

z

DM

M2

A *M2

DM

M1

A *M1

10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 42 45 47 48 50 52 55 58 60 62 65 68 70 72 75 78 80

6 7 8 9 10 10 11 12 13 14 14 15 16 17 18 18 19 20 21 22 22 23 24 25 26 26 27 28 29 30 30 32 34 36 37 38 40 42 45 46 48 50 53 54 56 58 60 62

2,25 2,25 2,25 2,25 2,25 2,25 2,25 2,25 2,25 2,25 2,25 2,25 2,25 2,25 2,25 2,25 2,25 2,25 2,25 2,25 2,25 2,25 2,25 2,25 2,25 2,25 2,25 2,25 2,25 2,25 2,25 2,25 2,25 2,25 2,25 2,25 2,25 2,25 2,25 2,25 2,25 2,25 2,25 2,25 2,25 2,25 2,25 2,25

5,276 6,052 7,230 8,007 9,060 10,276 11,132 12,249 13,099 14,158 15,276 16,170 17,257 18,143 19,193 20,276 21,192 22,261 23,170 24,212 25,276 26,207 27,264 28,187 29,224 30,276 31,217 32,266 33,200 34,232 35,276 37,267 40,276 42,268 43,216 45,276 47,269 50,276 53,227 55,276 57,270 60,276 63,235 65,276 67,271 70,276 73,271 75,276

1,71 1,85 2,13 2,41 2,99 1,72 1,81 1,95 2,08 2,26 1,72 1,79 1,88 1,96 2,07 1,73 1,78 1,85 1,91 1,99 1,73 1,77 1,83 1,87 1,94 1,73 1,77 1,81 1,85 1,90 1,73 1,80 1,73 1,79 1,82 1,73 1,79 1,73 1,81 1,73 1,78 1,73 1,79 1,73 1,77 1,73 1,70 1,73

4,5 3,5 3,0 2,75 2,5 3,25 3,0 2,75 2,5 2,5 3,0 2,75 2,5 2,5 2,5 2,75 2,75 2,5 2,5 2,5 2,75 2,5 2,5 2,5 2,5 2,5 2,5 2,5 2,5 2,5 2,5 2,5 2,5 2,5 2,5 2,5 2,5 2,5 2,5 2,5 2,5 2,5 2,5 2,5 2,5 2,5 2,5 2,5

16,629 15,279 15,554 15,851 16,503 19,075 19,417 20,059 20,360 21,548 23,602 23,940 24,477 25,433 26,578 28,050 29,026 29,513 30,480 31,599 33,103 33,423 34,540 35,514 36,614 37,477 38,460 39,561 40,540 41,627 42,502 44,577 47,523 49,590 50,576 52,540 54,602 57,554 60,600 62,566 64,619 67,577 70,617 72,586 74,632 77,594 80,552 82,601

1,03 1,08 1,20 1,25 1,37 1,19 1,23 1,31 1,38 1,43 1,28 1,33 1,41 1,43 1,47 1,36 1,38 1,45 1,47 1,51 1,40 1,45 1,48 1,50 1,53 1,46 1,48 1,51 1,53 1,55 1,48 1,53 1,50 1,54 1,56 1,52 1,56 1,54 1,59 1,55 1,58 1,56 1,60 1,57 1,60 1,58 1,56 1,59

2 2 2 2 2 3 3 3 3 3 3 3 3 3 4 4 4 4 4 4 5 5 5 5 5 5 5 5 5 6 6 6 7 7 7 7 7 8 8 9 9 9 9 10 10 11 11 11

a

a a a a a

a a a a a

a a

a a

a

6,013 5,946 5,879 5,813 5,746 9,647 9,580 9,513 9,446 9,379 9,879 9,813 9,746 9,679 13,013 13,513 13,446 13,379 13,313 13,246 17,147 17,080 17,013 16,946 16,879 17,379 17,313 17,246 17,179 20,513 21,013 20,879 24,647 24,513 24,446 24,879 24,746 28,513 28,313 32,147 32,013 32,379 32,179 36,013 35,879 39,647 40,013 39,879

These tooth thickness measurements are not reliable because they were made near the root fillet or the edge of the tip. Measurements between and over measuring circles are preferable. Deviations and tolerances can result in the unreliability of other tooth thickness measurements not identified by a.

19

SUPPLIED BY BSB UNDER LICENCE FROM DIN FOR ESCORTS LIMITED - FARIDABAD ON 29/12/2012

Basic data

DIN 5480-2:2006-05

10 Module m = 1,5 mm Table 14 — Nominal dimensions, m = 1,5 mm Dimensions in mm

Reference diameter

Number of teeth

Pitch diameter

Base diameter

dB

z

d

db

x1 ⋅ m

12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 42 45 47 48 50 52 55 58 60 62 65 68 70 72 75 78 80 82 85 88 90 92 95 98 100 105 110

6 7 8 8 9 10 10 11 12 12 13 14 14 15 16 16 17 18 18 19 20 20 21 22 22 23 24 24 25 26 28 30 30 32 33 35 37 38 40 42 44 45 46 48 50 52 53 55 57 58 60 62 64 64 68 72

9,0 10,5 12,0 12,0 13,5 15,0 15,0 16,5 18,0 18,0 19,5 21,0 21,0 22,5 24,0 24,0 25,5 27,0 27,0 28,5 30,0 30,0 31,5 33,0 33,0 34,5 36,0 36,0 37,5 39,0 42,0 45,0 45,0 48,0 49,5 52,5 55,5 57,0 60,0 63,0 66,0 67,5 69,0 72,0 75,0 78,0 79,5 82,5 85,5 87,0 90,0 93,0 96,0 96,0 102,0 108,0

7,794 9,093 10,392 10,392 11,691 12,990 12,990 14,289 15,588 15,588 16,887 18,187 18,187 19,486 20,785 20,785 22,084 23,383 23,383 24,682 25,981 25,981 27,280 28,579 28,579 29,878 31,177 31,177 32,476 33,775 36,373 38,971 38,971 41,569 42,868 45,466 48,064 49,363 51,962 54,560 57,158 58,457 59,756 62,354 64,952 67,550 68,849 71,447 74,045 75,344 77,942 80,540 83,138 83,138 88,335 93,531

0,675 0,425 0,175 0,675 0,425 0,175 0,675 0,425 0,175 0,675 0,425 0,175 0,675 0,425 0,175 0,675 0,425 0,175 0,675 0,425 0,175 0,675 0,425 0,175 0,675 0,425 0,175 0,675 0,425 0,675 0,675 0,175 0,675 0,175 0,425 0,425 0,425 0,675 0,175 0,175 0,175 0,425 0,675 0,675 0,675 0,175 0,425 0,425 0,425 0,675 0,175 0,175 0,175 1,175 0,675 0,175

20

Shaft Space width addendum Tooth modification thickness

Hub diameter

Shaft diameter

Root form Tip circle diameter diameter dFf2

Root diameter

Deviation

e2 = s1

df2

Adf2

min.

3,136 2,847 2,558 3,136 2,847 2,558 3,136 2,847 2,558 3,136 2,847 2,558 3,136 2,847 2,558 3,136 2,847 2,558 3,136 2,847 2,558 3,136 2,847 2,558 3,136 2,847 2,558 3,136 2,847 3,136 3,136 2,558 3,136 2,558 2,847 2,847 2,847 3,136 2,558 2,558 2,558 2,847 3,136 3,136 3,136 2,558 2,847 2,847 2,847 3,136 2,558 2,558 2,558 3,713 3,136 2,558

12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 42 45 47 48 50 52 55 58 60 62 65 68 70 72 75 78 80 82 85 88 90 92 95 98 100 105 110

0,39 0,40 0,40 0,40 0,40 0,40 0,40 0,40 0,40 0,40 0,40 0,40 0,40 0,40 0,41 0,41 0,41 0,41 0,41 0,41 0,41 0,41 0,41 0,41 0,41 0,41 0,41 0,41 0,41 0,41 0,41 0,41 0,41 0,41 0,42 0,42 0,42 0,42 0,42 0,42 0,42 0,42 0,42 0,42 0,42 0,42 0,42 0,42 0,42 0,42 0,42 0,42 0,42 0,42 0,44 0,44

11,75 12,76 13,76 14,76 15,76 16,76 17,76 18,76 19,76 20,76 21,76 22,76 23,76 24,76 25,76 26,76 27,76 28,76 29,76 30,76 31,76 32,76 33,76 34,76 35,76 36,76 37,76 38,76 39,76 41,76 44,76 46,76 47,76 49,76 51,77 54,77 57,77 59,77 61,77 64,77 67,77 69,77 71,77 74,77 77,77 79,77 81,77 84,77 87,77 89,77 91,77 94,77 97,77 99,77 104,78 109,78

Tip diameter

Root form circle diameter

da2

da1

9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 39 42 44 45 47 49 52 55 57 59 62 65 67 69 72 75 77 79 82 85 87 89 92 95 97 102 107

11,7 12,7 13,7 14,7 15,7 16,7 17,7 18,7 19,7 20,7 21,7 22,7 23,7 24,7 25,7 26,7 27,7 28,7 29,7 30,7 31,7 32,7 33,7 34,7 35,7 36,7 37,7 38,7 39,7 41,7 44,7 46,7 47,7 49,7 51,7 54,7 57,7 59,7 61,7 64,7 67,7 69,7 71,7 74,7 77,7 79,7 81,7 84,7 87,7 89,7 91,7 94,7 97,7 99,7 104,7 109,7

Root diameter

Deviation

max.

df1

Adf1

8,95 9,94 10,94 11,94 12,94 13,94 14,94 15,94 16,94 17,94 18,94 19,94 20,94 21,94 22,94 23,94 24,94 25,94 26,94 27,94 28,94 29,94 30,94 31,94 32,94 33,94 34,94 35,94 36,94 38,94 41,94 43,94 44,94 46,94 48,93 51,93 54,93 56,93 58,93 61,93 64,93 66,93 68,93 71,93 74,93 76,93 78,93 81,93 84,93 86,93 88,93 91,93 94,93 96,93 101,92 106,92

8,70 9,70 10,70 11,70 12,70 13,70 14,70 15,70 16,70 17,70 18,70 19,70 20,70 21,70 22,70 23,70 24,70 25,70 26,70 27,70 28,70 29,70 30,70 31,70 32,70 33,70 34,70 35,70 36,70 38,70 41,70 43,70 44,70 46,70 48,70 51,70 54,70 56,70 58,70 61,70 64,70 66,70 68,70 71,70 74,70 76,70 78,70 81,70 84,70 86,70 88,70 91,70 94,70 96,70 101,70 106,70

–0,61 –0,65 –0,65 –0,65 –0,65 –0,65 –0,65 –0,65 –0,65 –0,65 –0,65 –0,65 –0,65 –0,65 –0,69 –0,69 –0,69 –0,69 –0,69 –0,69 –0,69 –0,69 –0,69 –0,69 –0,69 –0,69 –0,69 –0,69 –0,69 –0,69 –0,69 –0,69 –0,69 –0,69 –0,73 –0,73 –0,73 –0,73 –0,73 –0,73 –0,73 –0,73 –0,73 –0,73 –0,73 –0,73 –0,73 –0,73 –0,73 –0,73 –0,73 –0,73 –0,73 –0,73 –0,79 –0,79

dFf1

SUPPLIED BY BSB UNDER LICENCE FROM DIN FOR ESCORTS LIMITED - FARIDABAD ON 29/12/2012

Nominal dimensions

Basic data

DIN 5480-2:2006-05

Table 15 — Inspection dimensions, m = 1,5 mm Dimensions in mm Hub dimensions

Shaft dimensions

Reference diameter

Number of teeth

Measuring circle diameter

Nominal dimension

dB

z

DM

M2

A *M2

DM

M1

A *M1

12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 42 45 47 48 50 52 55 58 60 62 65 68 70 72 75 78 80 82 85 88 90 92 95 98 100 105 110

6 7 8 8 9 10 10 11 12 12 13 14 14 15 16 16 17 18 18 19 20 20 21 22 22 23 24 24 25 26 28 30 30 32 33 35 37 38 40 42 44 45 46 48 50 52 53 55 57 58 60 62 64 64 68 72

2,75 2,75 2,5 2,75 2,75 2,75 2,75 2,75 2,75 2,75 2,75 2,75 2,75 2,75 2,75 2,75 2,75 2,75 2,75 2,75 2,75 2,75 2,75 2,75 2,75 2,75 2,75 2,75 2,75 2,75 2,75 2,75 2,75 2,75 2,75 2,75 2,75 2,75 2,75 2,75 2,75 2,75 2,75 2,75 2,75 2,75 2,75 2,75 2,75 2,75 2,75 2,75 2,75 2,75 2,75 2,75

6,180 6,868 8,877 9,180 9,939 10,985 12,181 12,983 14,038 15,181 16,014 17,068 18,181 19,036 20,087 21,181 22,053 23,101 24,181 25,067 26,111 27,181 28,078 29,118 30,181 31,087 32,125 33,181 34,094 36,181 39,181 41,138 42,181 44,141 46,115 49,119 52,122 54,181 56,150 59,151 62,153 64,133 66,181 69,181 72,181 74,157 76,140 79,142 82,143 84,181 86,161 89,161 92,162 94,168 99,181 104,164

1,77 2,18 2,13 1,76 2,03 2,67 1,76 1,96 2,33 1,75 1,91 2,18 1,75 1,88 2,09 1,75 1,86 2,03 1,75 1,85 1,99 1,74 1,84 1,96 1,74 1,83 1,93 1,74 1,82 1,74 1,74 1,88 1,74 1,87 1,80 1,79 1,79 1,74 1,84 1,83 1,83 1,78 1,74 1,74 1,74 1,81 1,77 1,77 1,77 1,74 1,80 1,80 1,80 1,69 1,74 1,79

5,5 4,0 3,5 4,5 3,5 3,25 4,0 3,5 3,0 3,5 3,25 3,0 3,5 3,25 3,0 3,5 3,25 3,0 3,25 3,0 3,0 3,25 3,0 3,0 3,25 3,0 3,0 3,25 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0

20,173 17,756 18,144 21,155 19,788 20,593 23,127 22,914 22,995 25,011 25,382 26,022 28,074 28,446 29,044 31,127 31,498 32,063 33,532 33,883 35,078 36,564 36,914 38,092 39,593 39,939 41,103 42,618 42,961 44,972 47,988 50,130 51,003 53,138 55,026 58,038 61,049 63,047 65,160 68,164 71,169 73,084 75,079 78,086 81,092 83,182 85,109 88,114 91,119 93,113 95,192 98,195 101,197 103,034 108,133 113,204

1,02 1,10 1,23 1,11 1,21 1,31 1,18 1,25 1,38 1,26 1,32 1,41 1,29 1,35 1,44 1,31 1,37 1,46 1,36 1,43 1,48 1,38 1,45 1,49 1,40 1,46 1,51 1,42 1,48 1,46 1,47 1,54 1,48 1,55 1,52 1,53 1,54 1,52 1,58 1,58 1,59 1,57 1,55 1,55 1,56 1,61 1,59 1,59 1,60 1,58 1,62 1,62 1,63 1,56 1,60 1,64

a

Deviation Measuring Nominal factor circle diameter dimension

Deviation factor

Number of teeth measured

k 2 2 2 2 2 2 3 3 3 3 3 3 3 3 3 4 4 4 4 4 4 4 4 4 5 5 5 5 5 5 6 6 6 6 6 7 7 7 7 8 8 8 9 9 9 9 10 10 10 11 11 11 11 12 12 13

a a a a

a a a

a a

a

a

a a

a

a a

a

a a

Nominal dimension

Wk 7,216 7,035 6,855 7,355 7,175 6,995 11,576 11,396 11,216 11,716 11,535 11,355 11,855 11,675 11,495 16,076 15,896 15,716 16,216 16,035 15,855 16,355 16,175 15,995 20,576 20,396 20,216 20,716 20,535 20,855 25,076 24,716 25,216 24,855 25,175 29,396 29,535 29,855 29,495 33,716 33,855 34,175 38,576 38,716 38,855 38,495 42,896 43,035 43,175 47,576 47,216 47,355 47,495 52,576 52,355 56,216

These tooth thickness measurements are not reliable because they were made near the root fillet or the edge of the tip. Measurements between and over measuring circles are preferable. Deviations and tolerances can result in the unreliability of other tooth thickness measurements not identified by a.

21

SUPPLIED BY BSB UNDER LICENCE FROM DIN FOR ESCORTS LIMITED - FARIDABAD ON 29/12/2012

Basic data

DIN 5480-2:2006-05

11 Module m = 1,75 mm Table 16 — Nominal dimensions, m = 1,75 mm Dimensions in mm ReferNumber ence of teeth diameter

dB 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 42 45 47 48 50 52 55 58 60 62 65 68 70 72 75 78 80 82 85 88 90 92 95 98 100 105 110 110 120 120 a

22

z 6 6 7 8a 8 9 9 10 10 11 12 12 13 13 14 14 15 16 16 17 17 18 18 19 20 20 21 21 22 24 25 26 27 28 30 32 33 34 36 37 38 40 41 43 44 45 47 49 50 51 53 54 56 58 60 61 66 67

Nominal dimensions

Hub diameter

Pitch diameter

Base diameter

Shaft addendum modification

Space width Tooth thickness

Root diameter

Deviation

d 10,50 10,50 12,25 14,00 14,00 15,75 15,75 17,50 17,50 19,25 21,00 21,00 22,75 22,75 24,50 24,50 26,25 28,00 28,00 29,75 29,75 31,50 31,50 33,25 35,00 35,00 36,75 36,75 38,50 42,00 43,75 45,50 47,25 49,00 52,50 56,00 57,75 59,50 63,00 64,75 66,50 70,00 71,75 75,25 77,00 78,75 82,25 85,75 87,50 89,25 92,75 94,50 98,00 101,50 105,00 106,75 115,50 117,25

db 9,093 9,093 10,609 12,124 12,124 13,640 13,640 15,155 15,155 16,671 18,187 18,187 19,702 19,702 21,218 21,218 22,733 24,249 24,249 25,764 25,764 27,280 27,280 28,795 30,311 30,311 31,826 31,826 33,342 36,373 37,889 39,404 40,920 42,435 45,466 48,497 50,013 51,529 54,560 56,075 57,591 60,622 62,137 65,168 66,684 68,200 71,231 74,262 75,777 77,293 80,324 81,839 84,870 87,902 90,933 92,448 100,026 101,541

x1 ⋅ m 0,2875 0,7875 0,4125 0,0375 0,5375 0,1625 0,6625 0,2875 0,7875 0,4125 0,0375 0,5375 0,1625 0,6625 0,2875 0,7875 0,4125 0,0375 0,5375 0,1625 0,6625 0,2875 0,7875 0,4125 0,0375 0,5375 0,1625 0,6625 0,7875 0,5375 0,6625 0,2875 0,4125 0,5375 0,2875 0,0375 0,1625 0,2875 0,0375 0,6625 0,7875 0,0375 0,6625 0,4125 0,5375 0,6625 0,4125 0,1625 0,2875 0,4125 0,1625 0,7875 0,0375 0,7875 1,5375 0,6625 1,2875 0,4125

e2 = s 1 3,081 3,658 3,225 2,792 3,370 2,937 3,514 3,081 3,658 3,225 2,792 3,370 2,937 3,514 3,081 3,658 3,225 2,792 3,370 2,937 3,514 3,081 3,658 3,225 2,792 3,370 2,937 3,514 3,658 3,370 3,514 3,081 3,225 3,370 3,081 2,792 2,937 3,081 2,792 3,514 3,658 2,792 3,514 3,225 3,370 3,514 3,225 2,937 3,081 3,225 2,937 3,658 2,792 3,658 4,524 3,514 4,236 3,225

df2 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 42 45 47 48 50 52 55 58 60 62 65 68 70 72 75 78 80 82 85 88 90 92 95 98 100 105 110 110 120 120

Adf2 0,46 0,46 0,46 0,46 0,46 0,46 0,46 0,46 0,46 0,46 0,46 0,46 0,46 0,47 0,47 0,47 0,47 0,47 0,47 0,47 0,47 0,47 0,47 0,47 0,47 0,47 0,47 0,47 0,47 0,47 0,47 0,47 0,47 0,49 0,49 0,49 0,49 0,49 0,49 0,49 0,49 0,49 0,49 0,49 0,49 0,49 0,49 0,49 0,49 0,49 0,49 0,49 0,49 0,51 0,51 0,51 0,51 0,51

A special tool is required for manufacturing splined shafts by shaping.

Shaft diameter

Root form circle Tip diameter diameter

dFf2

min. 12,71 13,71 14,71 15,71 16,71 17,71 18,71 19,71 20,71 21,71 22,71 23,71 24,71 25,72 26,72 27,72 28,72 29,72 30,72 31,72 32,72 33,72 34,72 35,72 36,72 37,72 38,72 39,72 41,72 44,72 46,72 47,72 49,72 51,73 54,73 57,73 59,73 61,73 64,73 67,73 69,73 71,73 74,73 77,73 79,73 81,73 84,73 87,73 89,73 91,73 94,73 97,73 99,73 104,74 109,74 109,74 119,74 119,74

da2 9,5 10,5 11,5 12,5 13,5 14,5 15,5 16,5 17,5 18,5 19,5 20,5 21,5 22,5 23,5 24,5 25,5 26,5 27,5 28,5 29,5 30,5 31,5 32,5 33,5 34,5 35,5 36,5 38,5 41,5 43,5 44,5 46,5 48,5 51,5 54,5 56,5 58,5 61,5 64,5 66,5 68,5 71,5 74,5 76,5 78,5 81,5 84,5 86,5 88,5 91,5 94,5 96,5 101,5 106,5 106,5 116,5 116,5

Tip diameter

Root form circle diameter

da1 12,65 13,65 14,65 15,65 16,65 17,65 18,65 19,65 20,65 21,65 22,65 23,65 24,65 25,65 26,65 27,65 28,65 29,65 30,65 31,65 32,65 33,65 34,65 35,65 36,65 37,65 38,65 39,65 41,65 44,65 46,65 47,65 49,65 51,65 54,65 57,65 59,65 61,65 64,65 67,65 69,65 71,65 74,65 77,65 79,65 81,65 84,65 87,65 89,65 91,65 94,65 97,65 99,65 104,65 109,65 109,65 119,65 119,65

max. 9,44 10,44 11,44 12,44 13,44 14,44 15,44 16,44 17,44 18,44 19,44 20,44 21,44 22,43 23,43 24,43 25,43 26,43 27,43 28,43 29,43 30,43 31,43 32,43 33,43 34,43 35,43 36,43 38,43 41,43 43,43 44,43 46,43 48,42 51,42 54,42 56,42 58,42 61,42 64,42 66,42 68,42 71,42 74,42 76,42 78,42 81,42 84,42 86,42 88,42 91,42 94,42 96,42 101,41 106,41 106,41 116,41 116,41

dFf1

Root diameter

Deviation

df1 9,15 10,15 11,15 12,15 13,15 14,15 15,15 16,15 17,15 18,15 19,15 20,15 21,15 22,15 23,15 24,15 25,15 26,15 27,15 28,15 29,15 30,15 31,15 32,15 33,15 34,15 35,15 36,15 38,15 41,15 43,15 44,15 46,15 48,15 51,15 54,15 56,15 58,15 61,15 64,15 66,15 68,15 71,15 74,15 76,15 78,15 81,15 84,15 86,15 88,15 91,15 94,15 96,15 101,15 106,15 106,15 116,15 116,15

Adf1 –0,74 –0,74 –0,74 –0,74 –0,74 –0,74 –0,74 –0,74 –0,74 –0,74 –0,74 –0,74 –0,74 –0,78 –0,78 –0,78 –0,78 –0,78 –0,78 –0,78 –0,78 –0,78 –0,78 –0,78 –0,78 –0,78 –0,78 –0,78 –0,78 –0,78 –0,78 –0,78 –0,78 –0,84 –0,84 –0,84 –0,84 –0,84 –0,84 –0,84 –0,84 –0,84 –0,84 –0,84 –0,84 –0,84 –0,84 –0,84 –0,84 –0,84 –0,84 –0,84 –0,84 –0,90 –0,90 –0,90 –0,90 –0,90

SUPPLIED BY BSB UNDER LICENCE FROM DIN FOR ESCORTS LIMITED - FARIDABAD ON 29/12/2012

Basic data

DIN 5480-2:2006-05

Table 17 — Inspection dimensions, m = 1,75 mm Dimensions in mm Reference diameter

a

Hub dimensions

Number of teeth

Measuring circle diameter

dB

z

13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 42 45 47 48 50 52 55 58 60 62 65 68 70 72 75 78 80 82 85 88 90 92 95 98 100 105 110 110 120 120

6 6 7 8 8 9 9 10 10 11 12 12 13 13 14 14 15 16 16 17 17 18 18 19 20 20 21 21 22 24 25 26 27 28 30 32 33 34 36 37 38 40 41 43 44 45 47 49 50 51 53 54 56 58 60 61 66 67

Shaft dimensions Measuring Nominal circle diameter dimension

Deviation factor

Number of teeth measured

Nominal dimension

Deviation factor

DM

M2

A*M2

DM

M1

A*M1

k

Wk

3,0 3,25 3,25 3,0 3,25 3,0 3,25 3,0 3,25 3,25 3,0 3,25 3,0 3,25 3,25 3,25 3,25 3,0 3,25 3,0 3,25 3,25 3,25 3,25 3,0 3,25 3,0 3,25 3,25 3,25 3,25 3,25 3,25 3,25 3,25 3,0 3,25 3,25 3,25 3,25 3,25 3,25 3,25 3,25 3,25 3,25 3,25 3,25 3,25 3,25 3,25 3,25 3,25 3,25 3,5 3,25 3,5 3,25

6,738 7,082 7,623 9,534 10,023 11,495 11,835 13,789 14,084 14,813 16,696 17,048 18,607 18,911 19,974 21,085 21,889 23,743 24,059 25,663 25,952 27,006 28,085 28,932 30,766 31,065 32,697 32,977 35,085 38,069 39,995 41,035 42,978 45,072 48,043 51,796 52,963 55,048 58,010 61,024 63,086 65,019 68,030 71,019 73,077 75,035 78,025 81,005 83,061 85,030 88,011 91,086 93,040 98,086 102,327 103,049 112,335 113,043

2,42 1,82 2,74 3,42 2,13 2,27 1,87 2,01 1,78 2,11 2,26 1,95 2,02 1,83 2,13 1,77 1,97 2,05 1,88 1,93 1,81 2,00 1,76 1,91 1,97 1,85 1,89 1,79 1,75 1,83 1,78 1,90 1,85 1,81 1,87 1,86 1,89 1,85 1,90 1,77 1,75 1,88 1,76 1,80 1,78 1,76 1,79 1,83 1,81 1,79 1,82 1,74 1,83 1,74 1,69 1,75 1,72 1,77

4,5 6 4,5 3,75 4,5 3,75 4,5 3,75 4,5 3,75 3,5 4,0 3,5 4,0 3,5 4,0 3,75 3,5 3,75 3,5 3,75 3,5 4,0 3,5 3,5 3,5 3,5 3,5 3,75 3,5 3,5 3,5 3,5 3,5 3,5 3,25 3,25 3,25 3,25 3,5 3,5 3,25 3,5 3,5 3,5 3,5 3,25 3,25 3,25 3,25 3,25 3,5 3,25 3,5 3,5 3,5 3,5 3,25

18,639 22,624 20,227 20,109 22,620 21,799 24,299 24,046 26,587 25,788 26,558 28,607 28,344 30,383 30,494 32,546 32,950 33,606 35,078 35,440 36,904 37,546 39,654 39,393 40,638 41,485 42,502 43,343 46,082 48,526 50,404 51,611 53,500 55,558 58,633 60,988 62,902 64,950 67,995 71,519 73,555 75,001 78,544 81,605 83,636 85,565 87,912 90,952 92,982 94,923 97,960 101,620 103,018 108,632 113,488 113,623 123,563 122,955

1,13 1,03 1,12 1,29 1,17 1,28 1,16 1,30 1,19 1,29 1,41 1,29 1,39 1,28 1,40 1,29 1,36 1,46 1,37 1,45 1,36 1,45 1,34 1,44 1,50 1,44 1,49 1,43 1,41 1,47 1,46 1,51 1,50 1,50 1,53 1,60 1,58 1,57 1,61 1,53 1,52 1,62 1,54 1,57 1,56 1,55 1,60 1,62 1,62 1,61 1,63 1,57 1,65 1,58 1,54 1,59 1,57 1,63

2 2 2 2 2 2 2 2 3 3 3 3 3 3 3 3 3 3 3 3 4 4 4 4 4 4 4 4 5 5 5 5 5 5 6 6 6 6 7 7 7 7 8 8 8 8 9 9 9 9 9 10 10 11 11 11 12 12

7,918 8,418 8,125 7,831 8,331 8,038 8,538 8,244 13,505 13,212 12,918 13,418 13,125 13,625 13,331 13,831 13,538 13,244 13,744 13,450 18,712 18,418 18,918 18,625 18,331 18,831 18,538 19,038 24,005 23,918 24,125 23,831 24,038 24,244 28,918 28,831 29,038 29,244 33,918 34,625 34,831 34,244 39,712 39,625 39,831 40,038 44,712 44,625 44,831 45,038 44,950 50,418 49,831 55,505 56,418 55,625 61,418 60,625

a a a a a

a

a a

a

a

a a a

a

a

a

Nominal dimension

These tooth thickness measurements are not reliable because they were made near the root fillet or the edge of the tip. Measurements between and over measuring circles are preferable. Deviations and tolerances can result in the unreliability of other tooth thickness measurements not identified by a.

23

SUPPLIED BY BSB UNDER LICENCE FROM DIN FOR ESCORTS LIMITED - FARIDABAD ON 29/12/2012

Basic data

DIN 5480-2:2006-05

12 Module m = 2 mm Table 18 — Nominal dimensions, m = 2 mm Dimensions in mm

Reference diameter

Number of teeth

Pitch diameter

Base diameter

Shaft Space width addendum Tooth modification thickness

Hub diameter Root diameter

Deviation

Root form circle diameter

dFf2

Shaft diameter Tip diameter

Tip diameter

Root form circle diameter

dFf1

Root diameter

Deviation

dB

z

d

db

x1 ⋅ m

e2 = s1

df2

Adf2

min.

da2

da1

max.

df1

Adf1

15 16 17 18 20 22 25 28 30 30 32 35 37 38 40 42 45 47 48 50 52 55 58 60 62 65 68 70 72 75 78 80 82 85 88 90 92 95 98 100 105 110 120 130 140 150

6 6 7 7 8 9 11 12 13 a 14 14 16 17 a 18 18 a 20 21 22 22 24 24 26 28 28 30 31 32 34 34 36 38 38 40 41 42 44 44 46 48 48 51 54 58 64 68 74

12 12 14 14 16 18 22 24 26 28 28 32 34 36 36 40 42 44 44 48 48 52 56 56 60 62 64 68 68 72 76 76 80 82 84 88 88 92 96 96 102 108 116 128 136 148

10,392 10,392 12,124 12,124 13,856 15,588 19,053 20,785 22,517 24,249 24,249 27,713 29,445 31,177 31,177 34,641 36,373 38,105 38,105 41,569 41,569 45,033 48,497 48,497 51,962 53,694 55,426 58,890 58,890 62,354 65,818 65,818 69,282 71,014 72,746 76,210 76,210 79,674 83,138 83,138 88,335 93,531 100,459 110,851 117,779 128,172

0,4 0,9 0,4 0,9 0,9 0,9 0,4 0,9 0,9 –0,1 0,9 0,4 0,4 –0,1 0,9 –0,1 0,4 0,4 0,9 –0,1 0,9 0,4 –0,1 0,9 –0,1 0,4 0,9 –0,1 0,9 0,4 –0,1 0,9 –0,1 0,4 0,9 –0,1 0,9 0,4 –0,1 0,9 0,4 –0,1 0,9 –0,1 0,9 –0,1

3,603 4,181 3,603 4,181 4,181 4,181 3,603 4,181 4,181 3,026 4,181 3,603 3,603 3,026 4,181 3,026 3,603 3,603 4,181 3,026 4,181 3,603 3,026 4,181 3,026 3,603 4,181 3,026 4,181 3,603 3,026 4,181 3,026 3,603 4,181 3,026 4,181 3,603 3,026 4,181 3,603 3,026 4,181 3,026 4,181 3,026

15 16 17 18 20 22 25 28 30 30 32 35 37 38 40 42 45 47 48 50 52 55 58 60 62 65 68 70 72 75 78 80 82 85 88 90 92 95 98 100 105 110 120 130 140 150

0,51 0,51 0,51 0,51 0,51 0,51 0,51 0,52 0,52 0,52 0,52 0,52 0,52 0,52 0,52 0,52 0,52 0,52 0,52 0,52 0,54 0,54 0,54 0,54 0,54 0,54 0,54 0,54 0,54 0,54 0,54 0,54 0,54 0,54 0,54 0,54 0,54 0,54 0,54 0,54 0,56 0,56 0,56 0,56 0,56 0,56

14,66 15,66 16,66 17,66 19,66 21,66 24,66 27,67 29,67 29,67 31,67 34,67 36,67 37,67 39,67 41,67 44,67 46,67 47,67 49,67 51,68 54,68 57,68 59,68 61,68 64,68 67,68 69,68 71,68 74,68 77,68 79,68 81,68 84,68 87,68 89,68 91,68 94,68 97,68 99,68 104,69 109,69 119,69 129,69 139,69 149,69

11 12 13 14 16 18 21 24 26 26 28 31 33 34 36 38 41 43 44 46 48 51 54 56 58 61 64 66 68 71 74 76 78 81 84 86 88 91 94 96 101 106 116 126 136 146

14,6 15,6 16,6 17,6 19,6 21,6 24,6 27,6 29,6 29,6 31,6 34,6 36,6 37,6 39,6 41,6 44,6 46,6 47,6 49,6 51,6 54,6 57,6 59,6 61,6 64,6 67,6 69,6 71,6 74,6 77,6 79,6 81,6 84,6 87,6 89,6 91,6 94,6 97,6 99,6 104,6 109,6 119,6 129,6 139,6 149,6

10,94 11,94 12,94 13,94 15,94 17,94 20,94 23,93 25,93 25,93 27,93 30,93 32,93 33,93 35,93 37,93 40,93 42,93 43,93 45,93 47,92 50,92 53,92 55,92 57,92 60,92 63,92 65,92 67,92 70,92 73,92 75,92 77,92 80,92 83,92 85,92 87,92 90,92 93,92 95,92 100,91 105,91 115,91 125,91 135,91 145,91

10,60 11,60 12,60 13,60 15,60 17,60 20,60 23,60 25,60 25,60 27,60 30,60 32,60 33,60 35,60 37,60 40,60 42,60 43,60 45,60 47,60 50,60 53,60 55,60 57,60 60,60 63,60 65,60 67,60 70,60 73,60 75,60 77,60 80,60 83,60 85,60 87,60 90,60 93,60 95,60 100,60 105,60 115,60 125,60 135,60 145,60

–0,79 –0,79 –0,79 –0,79 –0,79 –0,79 –0,79 –0,83 –0,83 –0,83 –0,83 –0,83 –0,83 –0,83 –0,83 –0,83 –0,83 –0,83 –0,83 –0,83 –0,89 –0,89 –0,89 –0,89 –0,89 –0,89 –0,89 –0,89 –0,89 –0,89 –0,89 –0,89 –0,89 –0,89 –0,89 –0,89 –0,89 –0,89 –0,89 –0,89 –0,95 –0,95 –0,95 –0,95 –0,95 –0,95

a

24

A special tool is required for manufacturing splined hubs by shaping.

SUPPLIED BY BSB UNDER LICENCE FROM DIN FOR ESCORTS LIMITED - FARIDABAD ON 29/12/2012

Nominal dimensions

Basic data

DIN 5480-2:2006-05

Table 19 — Inspection dimensions, m = 2 mm Dimensions in mm Hub dimensions

Shaft dimensions

Reference diameter

Number of teeth

Measuring circle diameter

Nominal dimension

Deviation factor

Measuring circle diameter

Nominal dimension

Deviation factor

dB

z

DM

M2

A*M2

DM

M1

A*M1

15 16 17 18 20 22 25 28 30 30 32 35 37 38 40 42 45 47 48 50 52 55 58 60 62 65 68 70 72 75 78 80 82 85 88 90 92 95 98 100 105 110 120 130 140 150

6 6 7 7 8 9 11 12 13 14 14 16 17 18 18 20 21 22 22 24 24 26 28 28 30 31 32 34 34 36 38 38 40 41 42 44 44 46 48 48 51 54 58 64 68 74

3,5 3,5 3,5 3,5 3,5 3,5 3,5 3,5 3,5 3,5 3,5 3,5 3,5 3,5 3,5 3,5 3,5 3,5 3,5 3,5 3,5 3,5 3,5 3,5 3,5 3,5 3,5 3,5 3,5 3,5 3,5 3,5 3,5 3,5 3,5 3,5 3,5 3,5 3,5 3,5 3,5 3,5 3,5 3,5 3,5 3,5

7,629 8,735 9,324 10,379 12,736 14,460 17,478 20,738 22,547 22,484 24,738 27,711 29,571 30,566 32,739 34,589 37,603 39,720 40,739 42,621 44,740 47,723 50,642 52,740 54,650 57,648 60,740 62,663 64,740 67,729 70,672 72,740 74,676 77,671 80,740 82,683 84,740 87,732 90,688 92,740 97,685 102,695 112,741 122,702 132,741 142,708

2,42 1,64 2,18 1,61 1,66 1,64 1,96 1,68 1,67 2,41 1,69 1,88 1,86 2,15 1,70 2,08 1,84 1,84 1,70 2,00 1,71 1,82 1,95 1,71 1,93 1,80 1,71 1,90 1,71 1,79 1,88 1,72 1,87 1,78 1,72 1,85 1,72 1,78 1,84 1,72 1,77 1,83 1,72 1,81 1,72 1,80

5,5 8,0 5,0 6,0 6,0 5,5 4,5 5,0 5,0 4,0 4,5 4,0 4,0 4,0 4,5 4,0 4,0 4,0 4,0 4,0 4,0 4,0 4,0 4,0 4,0 4,0 4,0 4,0 4,0 4,0 4,0 4,0 4,0 4,0 4,0 4,0 4,0 4,0 4,0 4,0 4,0 4,0 4,0 4,0 4,0 4,0

22,212 28,345 22,695 25,588 28,206 28,790 29,898 34,161 35,984 34,144 37,016 39,000 40,857 42,181 45,137 46,195 48,938 51,074 51,912 54,218 55,939 59,109 62,235 63,984 66,242 69,058 72,021 74,253 76,036 79,166 82,263 84,063 86,267 89,123 92,086 94,275 96,096 99,202 102,281 104,114 109,165 114,289 124,150 134,299 144,177 154,306

1,11 1,01 1,13 1,06 1,11 1,13 1,28 1,23 1,24 1,46 1,30 1,42 1,42 1,50 1,35 1,52 1,46 1,47 1,43 1,54 1,44 1,50 1,56 1,47 1,57 1,53 1,49 1,59 1,50 1,55 1,60 1,52 1,61 1,57 1,54 1,62 1,54 1,58 1,62 1,55 1,59 1,63 1,58 1,65 1,60 1,66

a

Number of Nominal teeth dimension measured

k 2 2 2 2 2 2 3 3 3 3 3 3 4 3 4 4 4 4 5 4 5 5 5 6 5 6 6 6 7 7 7 7 7 8 8 8 8 8 8 9 9 9 11 11 12 13

a a a

a a a a

a a

a a

a a

a a a

a

a

Wk 9,121 9,621 9,214 9,714 9,807 9,900 15,028 15,621 15,714 14,807 15,807 15,493 21,028 15,179 21,621 20,807 21,400 21,493 27,434 21,179 27,621 27,307 26,993 33,434 27,179 33,214 33,807 32,993 39,434 39,121 38,807 39,807 38,993 45,028 45,621 44,807 45,807 45,493 45,179 51,621 51,400 51,179 63,434 62,993 69,807 74,807

These tooth thickness measurements are not reliable because they were made near the root fillet or the edge of the tip. Measurements between and over measuring circles are preferable. Deviations and tolerances can result in the unreliability of other tooth thickness measurements not identified by a.

25

SUPPLIED BY BSB UNDER LICENCE FROM DIN FOR ESCORTS LIMITED - FARIDABAD ON 29/12/2012

Basic data

DIN 5480-2:2006-05

13 Module m = 2,5 mm Table 20 — Nominal dimensions, m = 2,5 mm Dimensions in mm

ReferNumber ence of teeth diameter

dB

z

20 22 25 28 30 32 35 37 38 40 42 45 47 48 50 52 55 58 60 62 65 68 70 72 75 78 80 82 85 88 90 92 95 98 100 105 110 120 130 140 150

6 7 8 10 10 11 12 13 14 14 15 16 17 18 18 19 20 22 22 23 24 26 26 27 28 30 30 31 32 34 34 35 36 38 38 40 42 46 50 54 58

26

Pitch diameter

Base diameter

d

db

15,0 12,990 17,5 15,155 20,0 17,321 25,0 21,651 25,0 21,651 27,5 23,816 30,0 25,981 32,5 28,146 35,0 30,311 35,0 30,311 37,5 32,476 40,0 34,641 42,5 36,806 45,0 38,971 45,0 38,971 47,5 41,136 50,0 43,301 55,0 47,631 55,0 47,631 57,5 49,796 60,0 51,962 65,0 56,292 65,0 56,292 67,5 58,457 70,0 60,622 75,0 64,952 75,0 64,952 77,5 67,117 80,0 69,282 85,0 73,612 85,0 73,612 87,5 75,777 90,0 77,942 95,0 82,272 95,0 82,272 100,0 86,603 105,0 90,933 115,0 99,593 125,0 108,253 135,0 116,913 145,0 125,574

Shaft Space width addendum Tooth modification thickness

Hub diameter Root diameter

Deviation

Root form circle diameter

dFf2

Shaft diameter Tip diameter

Tip diameter

Root form circle diameter

dFf1

Root Deviation diameter

x1 ⋅ m

e2 = s1

df2

Adf2

min.

da2

da1

max.

df1

Adf1

1,125 0,875 1,125 0,125 1,125 0,875 1,125 0,875 0,125 1,125 0,875 1,125 0,875 0,125 1,125 0,875 1,125 0,125 1,125 0,875 1,125 0,125 1,125 0,875 1,125 0,125 1,125 0,875 1,125 0,125 1,125 0,875 1,125 0,125 1,125 1,125 1,125 1,125 1,125 1,125 1,125

5,226 4,937 5,226 4,071 5,226 4,937 5,226 4,937 4,071 5,226 4,937 5,226 4,937 4,071 5,226 4,937 5,226 4,071 5,226 4,937 5,226 4,071 5,226 4,937 5,226 4,071 5,226 4,937 5,226 4,071 5,226 4,937 5,226 4,071 5,226 5,226 5,226 5,226 5,226 5,226 5,226

20 22 25 28 30 32 35 37 38 40 42 45 47 48 50 52 55 58 60 62 65 68 70 72 75 78 80 82 85 88 90 92 95 98 100 105 110 120 130 140 150

0,61 0,61 0,61 0,62 0,62 0,62 0,62 0,62 0,62 0,62 0,62 0,62 0,62 0,62 0,62 0,64 0,64 0,64 0,64 0,64 0,64 0,64 0,64 0,64 0,64 0,64 0,64 0,64 0,64 0,64 0,64 0,64 0,64 0,64 0,64 0,66 0,66 0,66 0,66 0,66 0,66

19,56 21,56 24,56 27,57 29,57 31,57 34,57 36,57 37,57 39,57 41,57 44,57 46,57 47,57 49,57 51,58 54,58 57,58 59,58 61,58 64,58 67,58 69,58 71,58 74,58 77,58 79,58 81,58 84,58 87,58 89,58 91,58 94,58 97,58 99,58 104,59 109,59 119,59 129,59 139,59 149,59

15 17 20 23 25 27 30 32 33 35 37 40 42 43 45 47 50 53 55 57 60 63 65 67 70 73 75 77 80 83 85 87 90 93 95 100 105 115 125 135 145

19,5 21,5 24,5 27,5 29,5 31,5 34,5 36,5 37,5 39,5 41,5 44,5 46,5 47,5 49,5 51,5 54,5 57,5 59,5 61,5 64,5 67,5 69,5 71,5 74,5 77,5 79,5 81,5 84,5 87,5 89,5 91,5 94,5 97,5 99,5 104,5 109,5 119,5 129,5 139,5 149,5

14,94 16,94 19,94 22,93 24,93 26,93 29,93 31,93 32,93 34,93 36,93 39,93 41,93 42,93 44,93 46,92 49,92 52,92 54,92 56,92 59,92 62,92 64,92 66,92 69,92 72,92 74,92 76,92 79,92 82,92 84,92 86,92 89,92 92,92 94,92 99,91 104,91 114,91 124,91 134,91 144,91

14,50 16,50 19,50 22,50 24,50 26,50 29,50 31,50 32,50 34,50 36,50 39,50 41,50 42,50 44,50 46,50 49,50 52,50 54,50 56,50 59,50 62,50 64,50 66,50 69,50 72,50 74,50 76,50 79,50 82,50 84,50 86,50 89,50 92,50 94,50 99,50 104,50 114,50 124,50 134,50 144,50

–0,89 –0,89 –0,89 –0,93 –0,93 –0,93 –0,93 –0,93 –0,93 –0,93 –0,93 –0,93 –0,93 –0,93 –0,93 –0,99 –0,99 –0,99 –0,99 –0,99 –0,99 –0,99 –0,99 –0,99 –0,99 –0,99 –0,99 –0,99 –0,99 –0,99 –0,99 –0,99 –0,99 –0,99 –0,99 –1,05 –1,05 –1,05 –1,05 –1,05 –1,05

SUPPLIED BY BSB UNDER LICENCE FROM DIN FOR ESCORTS LIMITED - FARIDABAD ON 29/12/2012

Nominal dimensions

Basic data

DIN 5480-2:2006-05

Table 21 — Inspection dimensions, m = 2,5 mm Dimensions in mm Hub dimensions

Shaft dimensions

Reference diameter

Number of teeth

Measuring circle diameter

Nominal dimension

Deviation factor

Measuring circle diameter

Nominal dimension

Deviation factor

Number of teeth measured

Nominal dimension

dB

z

DM

M2

A*M2

DM

M1

A*M1

k

Wk

20 22 25 28 30 32 35 37 38 40 42 45 47 48 50 52 55 58 60 62 65 68 70 72 75 78 80 82 85 88 90 92 95 98 100 105 110 120 130 140 150

6 7 8 10 10 11 12 13 14 14 15 16 17 18 18 19 20 22 22 23 24 26 26 27 28 30 30 31 32 34 34 35 36 38 38 40 42 46 50 54 58

4,5 4,5 4,5 4,25 4,5 4,5 4,5 4,5 4,5 4,5 4,5 4,5 4,5 4,5 4,5 4,5 4,5 4,5 4,5 4,5 4,5 4,5 4,5 4,5 4,5 4,5 4,5 4,5 4,5 4,5 4,5 4,5 4,5 4,5 4,5 4,5 4,5 4,5 4,5 4,5 4,5

10,551 12,105 15,552 19,115 20,552 22,265 25,552 27,308 28,316 30,552 32,340 35,552 37,365 38,387 40,552 42,384 45,552 48,424 50,552 52,413 55,552 58,448 60,552 62,434 65,552 68,464 70,552 72,449 75,552 78,476 80,552 82,461 85,552 88,485 90,552 95,552 100,552 110,552 120,552 130,552 140,552

1,71 1,85 1,72 2,30 1,72 1,81 1,72 1,80 2,26 1,72 1,79 1,73 1,78 2,07 1,73 1,78 1,73 1,99 1,73 1,77 1,73 1,94 1,73 1,77 1,73 1,90 1,73 1,76 1,73 1,88 1,73 1,76 1,73 1,86 1,73 1,73 1,73 1,73 1,73 1,73 1,73

9,0 7,0 7,0 5,0 6,5 6,0 6,0 5,5 5,0 6,0 5,5 5,5 5,5 5,0 5,5 5,5 5,5 5,0 5,5 5,0 5,0 5,0 5,0 5,0 5,0 5,0 5,0 5,0 5,0 5,0 5,0 5,0 5,0 5,0 5,0 5,0 5,0 5,0 5,0 5,0 5,0

33,258 30,558 34,113 33,006 38,151 38,835 42,093 42,764 43,096 47,204 47,881 51,035 52,974 53,156 56,100 58,052 61,157 63,198 66,206 66,846 69,924 73,229 74,954 76,920 79,980 83,253 85,004 86,978 90,026 93,272 95,045 97,024 100,063 103,288 105,079 110,094 115,108 125,132 135,153 145,172 155,188

1,03 1,08 1,13 1,37 1,19 1,23 1,25 1,30 1,43 1,28 1,33 1,33 1,36 1,47 1,36 1,38 1,38 1,51 1,40 1,45 1,44 1,53 1,46 1,48 1,47 1,55 1,48 1,50 1,49 1,57 1,50 1,52 1,51 1,58 1,52 1,53 1,54 1,55 1,56 1,57 1,58

a

2 2 2 2 3 3 3 3 3 3 3 4 4 4 4 4 4 4 5 5 5 5 5 5 6 6 6 6 6 6 7 7 7 7 7 8 8 9 9 10 11

a

a

a a a

a

a

a a

a

a

a

a

12,026 11,892 12,259 11,491 19,293 19,159 19,526 19,392 18,759 19,759 19,625 26,793 26,659 26,026 27,026 26,892 27,259 26,491 34,293 34,159 34,526 33,759 34,759 34,625 41,793 41,026 42,026 41,892 42,259 41,491 49,293 49,159 49,526 48,759 49,759 56,793 57,026 64,293 64,759 72,026 79,293

These tooth thickness measurements are not reliable because they were made near the root fillet or the edge of the tip. Measurements between and over measuring circles are preferable. Deviations and tolerances can result in the unreliability of other tooth thickness measurements not identified by a.

27

SUPPLIED BY BSB UNDER LICENCE FROM DIN FOR ESCORTS LIMITED - FARIDABAD ON 29/12/2012

Basic data

DIN 5480-2:2006-05

14 Module m = 3 mm Table 22 — Nominal dimensions, m = 3 mm Dimensions in mm

Refer- Number of ence diameter teeth

Pitch diameter

Base diameter

Space width Shaft Tooth addendum modification thickness

Hub diameter Root diameter

Deviation

Root form circle diameter

dFf2

Shaft diameter Tip diameter

Tip diameter

Root form circle diameter

dFf1

Root Deviation diameter

dB

z

d

db

x1 ⋅ m

e2 = s1

df2

Adf2

min.

da2

da1

max.

df1

Adf1

22 25 28 30 32 35 37 38 40 42 45 45 47 48 50 52 55 58 60 62 65 68 70 72 75 78 80 82 85 88 90 92 95 98 100 105 110 120 130 140 150 160 170 180 190 200 210 210

6 7 8 8 9 10 11 11 12 12 13 14 a 14 14 15 16 17 18 18 19 20 21 22 22 24 24 25 26 27 28 28 29 30 31 32 34 35 38 42 45 48 52 55 58 62 65 68 69

18 21 24 24 27 30 33 33 36 36 39 42 42 42 45 48 51 54 54 57 60 63 66 66 72 72 75 78 81 84 84 87 90 93 96 102 105 114 126 135 144 156 165 174 186 195 204 207

15,588 18,187 20,785 20,785 23,383 25,981 28,579 28,579 31,177 31,177 33,775 36,373 36,373 36,373 38,971 41,569 44,167 46,765 46,765 49,363 51,962 54,560 57,158 57,158 62,354 62,354 64,952 67,550 70,148 72,746 72,746 75,344 77,942 80,540 83,138 88,335 90,933 98,727 109,119 116,913 124,708 135,100 142,894 150,688 161,081 168,875 176,669 179,267

0,35 0,35 0,35 1,35 0,85 0,85 0,35 0,85 0,35 1,35 1,35 –0,15 0,85 1,35 0,85 0,35 0,35 0,35 1,35 0,85 0,85 0,85 0,35 1,35 –0,15 1,35 0,85 0,35 0,35 0,35 1,35 0,85 0,85 0,85 0,35 –0,15 0,85 1,35 0,35 0,85 1,35 0,35 0,85 1,35 0,35 0,85 1,35 –0,15

5,117 5,117 5,117 6,271 5,694 5,694 5,117 5,694 5,117 6,271 6,271 4,539 5,694 6,271 5,694 5,117 5,117 5,117 6,271 5,694 5,694 5,694 5,117 6,271 4,539 6,271 5,694 5,117 5,117 5,117 6,271 5,694 5,694 5,694 5,117 4,539 5,694 6,271 5,117 5,694 6,271 5,117 5,694 6,271 5,117 5,694 6,271 4,539

22 25 28 30 32 35 37 38 40 42 45 45 47 48 50 52 55 58 60 62 65 68 70 72 75 78 80 82 85 88 90 92 95 98 100 105 110 120 130 140 150 160 170 180 190 200 210 210

0,71 0,71 0,72 0,72 0,72 0,72 0,72 0,72 0,72 0,72 0,72 0,72 0,72 0,72 0,72 0,74 0,74 0,74 0,74 0,74 0,74 0,74 0,74 0,74 0,74 0,74 0,74 0,74 0,74 0,74 0,74 0,74 0,74 0,74 0,74 0,76 0,76 0,76 0,76 0,76 0,76 0,76 0,76 0,76 0,76 0,76 0,77 0,77

21,46 24,46 27,47 29,47 31,47 34,47 36,47 37,47 39,47 41,47 44,47 44,47 46,47 47,47 49,47 51,48 54,48 57,48 59,48 61,48 64,48 67,48 69,48 71,48 74,48 77,48 79,48 81,48 84,48 87,48 89,48 91,48 94,48 97,48 99,48 104,49 109,49 119,49 129,49 139,49 149,49 159,49 169,49 179,49 189,49 199,49 209,50 209,50

16 19 22 24 26 29 31 32 34 36 39 39 41 42 44 46 49 52 54 56 59 62 64 66 69 72 74 76 79 82 84 86 89 92 94 99 104 114 124 134 144 154 164 174 184 194 204 204

21,4 24,4 27,4 29,4 31,4 34,4 36,4 37,4 39,4 41,4 44,4 44,4 46,4 47,4 49,4 51,4 54,4 57,4 59,4 61,4 64,4 67,4 69,4 71,4 74,4 77,4 79,4 81,4 84,4 87,4 89,4 91,4 94,4 97,4 99,4 104,4 109,4 119,4 129,4 139,4 149,4 159,4 169,4 179,4 189,4 199,4 209,4 209,4

15,94 18,94 21,93 23,93 25,93 28,93 30,93 31,93 33,93 35,93 38,93 38,93 40,93 41,93 43,93 45,92 48,92 51,92 53,92 55,92 58,92 61,92 63,92 65,92 68,92 71,92 73,92 75,92 78,92 81,92 83,92 85,92 88,92 91,92 93,92 98,91 103,91 113,91 123,91 133,91 143,91 153,91 163,91 173,91 183,91 193,91 203,90 203,90

15,40 18,40 21,40 23,40 25,40 28,40 30,40 31,40 33,40 35,40 38,40 38,40 40,40 41,40 43,40 45,40 48,40 51,40 53,40 55,40 58,40 61,40 63,40 65,40 68,40 71,40 73,40 75,40 78,40 81,40 83,40 85,40 88,40 91,40 93,40 98,40 103,40 113,40 123,40 133,40 143,40 153,40 163,40 173,40 183,40 193,40 203,40 203,40

–0,99 –0,99 –1,03 –1,03 –1,03 –1,03 –1,03 –1,03 –1,03 –1,03 –1,03 –1,03 –1,03 –1,03 –1,03 –1,09 –1,09 –1,09 –1,09 –1,09 –1,09 –1,09 –1,09 –1,09 –1,09 –1,09 –1,09 –1,09 –1,09 –1,09 –1,09 –1,09 –1,09 –1,09 –1,09 –1,15 –1,15 –1,15 –1,15 –1,15 –1,15 –1,15 –1,15 –1,15 –1,15 –1,15 –1,22 –1,22

a

28

A special tool is required for manufacturing splined hubs by shaping.

SUPPLIED BY BSB UNDER LICENCE FROM DIN FOR ESCORTS LIMITED - FARIDABAD ON 29/12/2012

Nominal dimensions

Basic data

DIN 5480-2:2006-05

Table 23 — Inspection dimensions, m = 3 mm Dimensions in mm Reference diameter

a

Hub dimensions

Number of teeth

Measuring circle diameter

dB

z

22 25 28 30 32 35 37 38 40 42 45 45 47 48 50 52 55 58 60 62 65 68 70 72 75 78 80 82 85 88 90 92 95 98 100 105 110 120 130 140 150 160 170 180 190 200 210 210

6 7 8 8 9 10 11 11 12 12 13 14 14 14 15 16 17 18 18 19 20 21 22 22 24 24 25 26 27 28 28 29 30 31 32 34 35 38 42 45 48 52 55 58 62 65 68 69

Shaft dimensions

Nominal dimension

Deviation factor

Measuring circle diameter

DM

M2

A*M2

5,0 5,0 5,25 5,25 5,25 5,25 5,25 5,25 5,25 5,25 5,25 5,25 5,25 5,25 5,25 5,25 5,25 5,25 5,25 5,25 5,25 5,25 5,25 5,25 5,25 5,25 5,25 5,25 5,25 5,25 5,25 5,25 5,25 5,25 5,25 5,25 5,25 5,25 5,25 5,25 5,25 5,5 5,5 5,5 5,5 5,5 5,5 5,5

11,694 14,235 16,835 19,104 20,686 24,089 25,627 26,762 28,964 31,107 33,820 33,726 36,096 37,108 38,855 41,010 43,807 47,023 49,109 50,908 54,101 56,928 59,042 61,109 63,932 67,109 68,957 71,054 73,922 77,059 79,110 80,978 84,105 86,987 89,066 93,994 99,001 109,110 119,078 129,026 139,111 148,315 158,283 168,362 178,323 188,295 198,362 198,232

2,42 2,18 2,56 1,66 1,85 1,86 2,14 1,83 2,10 1,68 1,67 2,41 1,82 1,69 1,80 1,97 1,95 1,94 1,70 1,79 1,79 1,78 1,89 1,70 2,00 1,71 1,78 1,86 1,85 1,85 1,71 1,77 1,77 1,77 1,83 1,90 1,76 1,72 1,81 1,76 1,72 1,81 1,77 1,74 1,80 1,76 1,74 1,82

Number of Nominal teeth dimension measured

Nominal dimension

Deviation factor

DM

M1

A*M1

k

7,0 7,0 7,0 8,0 7,0 7,0 6,0 7,0 6,0 7,0 7,0 6,0 6,0 7,0 6,0 6,0 6,0 6,0 7,0 6,0 6,0 6,0 6,0 6,0 6,0 6,0 6,0 6,0 6,0 6,0 6,0 6,0 6,0 6,0 6,0 6,0 6,0 6,0 6,0 6,0 6,0 6,0 6,0 6,0 6,0 6,0 6,0 6,0

30,099 32,544 36,289 40,013 39,577 43,158 42,581 45,828 45,989 50,023 52,752 51,216 52,848 56,148 55,606 58,088 60,873 64,125 68,343 67,767 70,999 73,827 76,183 77,868 81,326 83,909 85,923 88,227 91,092 94,245 95,977 97,995 101,141 104,025 106,275 111,380 116,076 126,095 136,329 146,167 156,172 166,364 176,228 186,226 196,389 206,272 216,266 216,400

1,17 1,17 1,23 1,14 1,21 1,25 1,35 1,25 1,38 1,26 1,26 1,46 1,37 1,29 1,38 1,44 1,44 1,46 1,34 1,43 1,44 1,45 1,49 1,43 1,54 1,44 1,48 1,52 1,52 1,53 1,47 1,50 1,51 1,51 1,55 1,59 1,53 1,52 1,58 1,57 1,55 1,61 1,59 1,58 1,62 1,61 1,60 1,65

2 2 2 2 2 2 2 3 3 3 3 3 3 3 3 3 3 4 4 4 4 4 4 5 4 5 5 5 5 5 6 6 6 6 6 6 7 7 8 8 9 9 10 11 11 12 12 12

Wk a

a a a a a

a a a

a

a

a

a a a

a

13,431 13,571 13,710 14,710 14,350 14,490 14,129 22,791 22,431 23,431 23,571 22,210 23,210 23,710 23,350 22,990 23,129 31,431 32,431 32,071 32,210 32,350 31,990 41,152 31,769 41,431 41,071 40,710 40,850 40,990 50,152 49,791 49,931 50,071 49,710 49,490 58,791 59,710 67,431 68,350 77,431 76,990 86,071 95,152 94,710 103,791 104,710 103,350

These tooth thickness measurements are not reliable because they were made near the root fillet or the edge of the tip. Measurements between and over measuring circles are preferable. Deviations and tolerances can result in the unreliability of other tooth thickness measurements not identified by a.

29

SUPPLIED BY BSB UNDER LICENCE FROM DIN FOR ESCORTS LIMITED - FARIDABAD ON 29/12/2012

Basic data

DIN 5480-2:2006-05

15 Module m = 4 mm Table 24 — Nominal dimensions, m = 4 mm Dimensions in mm

Refer- Number of ence diameter teeth

Pitch diameter

Base diameter

Hub diameter

Shaft addendum modification

Space width Tooth thickness

Root diameter

Deviation

Root form circle diameter

dFf2

Shaft diameter Tip diameter

Tip diameter

Root form circle diameter

dFf1

Root Deviation diameter

dB

z

d

db

x1 ⋅ m

e2 = s1

df2

Adf2

min.

da2

da1

max.

df1

Adf1

32 35 37 38 40 42 45 47 48 50 52 55 58 60 60 62 65 68 68 70 72 75 78 80 82 85 88 90 92 95 98 100 105 110 120 130 140 150 160 170 180 190 200 210

6 7 8 8 8 9 10 10 10 11 11 12 13 13 a 14 14 15 15 16 a 16 16 17 18 18 19 20 20 21 22 22 23 24 25 26 28 31 34 36 38 41 44 46 48 51

24 28 32 32 32 36 40 40 40 44 44 48 52 52 56 56 60 60 64 64 64 68 72 72 76 80 80 84 88 88 92 96 100 104 112 124 136 144 152 164 176 184 192 204

20,785 24,249 27,713 27,713 27,713 31,177 34,641 34,641 34,641 38,105 38,105 41,569 45,033 45,033 48,497 48,497 51,962 51,962 55,426 55,426 55,426 58,890 62,354 62,354 65,818 69,282 69,282 72,746 76,210 76,210 79,674 83,138 86,603 90,067 96,995 107,387 117,779 124,708 131,636 142,028 152,420 159,349 166,277 176,669

1,8 1,3 0,3 0,8 1,8 0,8 0,3 1,3 1,8 0,8 1,8 1,3 0,8 1,8 –0,2 0,8 0,3 1,8 –0,2 0,8 1,8 1,3 0,8 1,8 0,8 0,3 1,8 0,8 –0,2 1,3 0,8 –0,2 0,3 0,8 1,8 0,8 –0,2 0,8 1,8 0,8 –0,2 0,8 1,8 0,8

8,362 7,784 6,630 7,207 8,362 7,207 6,630 7,784 8,362 7,207 8,362 7,784 7,207 8,362 6,052 7,207 6,630 8,362 6,052 7,207 8,362 7,784 7,207 8,362 7,207 6,630 8,362 7,207 6,052 7,784 7,207 6,052 6,630 7,207 8,362 7,207 6,052 7,207 8,362 7,207 6,052 7,207 8,362 7,207

32 35 37 38 40 42 45 47 48 50 52 55 58 60 60 62 65 68 68 70 72 75 78 80 82 85 88 90 92 95 98 100 105 110 120 130 140 150 160 170 180 190 200 210

0,92 0,92 0,92 0,92 0,92 0,92 0,92 0,92 0,92 0,92 0,94 0,94 0,94 0,94 0,94 0,94 0,94 0,94 0,94 0,94 0,94 0,94 0,94 0,94 0,94 0,94 0,94 0,94 0,94 0,94 0,94 0,94 0,96 0,96 0,96 0,96 0,96 0,96 0,96 0,96 0,96 0,96 0,96 0,97

31,27 34,27 36,27 37,27 39,27 41,27 44,27 46,27 47,27 49,27 51,28 54,28 57,28 59,28 59,28 61,28 64,28 67,28 67,28 69,28 71,28 74,28 77,28 79,28 81,28 84,28 87,28 89,28 91,28 94,28 97,28 99,28 104,29 109,29 119,29 129,29 139,29 149,29 159,29 169,29 179,29 189,29 199,29 209,30

24 27 29 30 32 34 37 39 40 42 44 47 50 52 52 54 57 60 60 62 64 67 70 72 74 77 80 82 84 87 90 92 97 102 112 122 132 142 152 162 172 182 192 202

31,2 34,2 36,2 37,2 39,2 41,2 44,2 46,2 47,2 49,2 51,2 54,2 57,2 59,2 59,2 61,2 64,2 67,2 67,2 69,2 71,2 74,2 77,2 79,2 81,2 84,2 87,2 89,2 91,2 94,2 97,2 99,2 104,2 109,2 119,2 129,2 139,2 149,2 159,2 169,2 179,2 189,2 199,2 209,2

23,93 26,93 28,93 29,93 31,93 33,93 36,93 38,93 39,93 41,93 43,92 46,92 49,92 51,92 51,92 53,92 56,92 59,92 59,92 61,92 63,92 66,92 69,92 71,92 73,92 76,92 79,92 81,92 83,92 86,92 89,92 91,92 96,91 101,91 111,91 121,91 131,91 141,91 151,91 161,91 171,91 181,91 191,91 201,90

23,20 26,20 28,20 29,20 31,20 33,20 36,20 38,20 39,20 41,20 43,20 46,20 49,20 51,20 51,20 53,20 56,20 59,20 59,20 61,20 63,20 66,20 69,20 71,20 73,20 76,20 79,20 81,20 83,20 86,20 89,20 91,20 96,20 101,20 111,20 121,20 131,20 141,20 151,20 161,20 171,20 181,20 191,20 201,20

–1,23 –1,23 –1,23 –1,23 –1,23 –1,23 –1,23 –1,23 –1,23 –1,23 –1,29 –1,29 –1,29 –1,29 –1,29 –1,29 –1,29 –1,29 –1,29 –1,29 –1,29 –1,29 –1,29 –1,29 –1,29 –1,29 –1,29 –1,29 –1,29 –1,29 –1,29 –1,29 –1,35 –1,35 –1,35 –1,35 –1,35 –1,35 –1,35 –1,35 –1,35 –1,35 –1,35 –1,42

a

30

A special tool is required for manufacturing splined hubs by shaping.

SUPPLIED BY BSB UNDER LICENCE FROM DIN FOR ESCORTS LIMITED - FARIDABAD ON 29/12/2012

Nominal dimensions

Basic data

DIN 5480-2:2006-05

Table 25 — Inspection dimensions, m = 4 mm Dimensions in mm Hub dimensions

Shaft dimensions

Reference diameter

Number of teeth

Measuring circle diameter

Nominal dimension

Deviation factor

Measuring circle diameter

Nominal dimension

Deviation factor

dB

z

DM

M2

A*M2

DM

M1

A*M1

32 35 37 38 40 42 45 47 48 50 52 55 58 60 60 62 65 68 68 70 72 75 78 80 82 85 88 90 92 95 98 100 105 110 120 130 140 150 160 170 180 190 200 210

6 7 8 8 8 9 10 10 10 11 11 12 13 13 14 14 15 15 16 16 16 17 18 18 19 20 20 21 22 22 23 24 25 26 28 31 34 36 38 41 44 46 48 51

7,0 7,0 7,0 7,0 7,0 7,0 7,0 7,0 7,0 7,0 7,0 7,0 7,0 7,0 7,0 7,0 7,0 7,0 7,0 7,0 7,0 7,0 7,0 7,0 7,0 7,0 7,0 7,0 7,0 7,0 7,0 7,0 7,0 7,0 7,0 7,0 7,0 7,0 7,0 7,0 7,0 7,0 7,5 7,0

17,470 19,778 21,913 23,337 25,473 26,837 30,113 32,472 33,475 34,955 37,023 40,474 43,037 45,094 44,967 47,411 49,965 53,146 53,066 55,421 57,478 60,189 63,429 65,478 67,178 70,340 73,479 75,207 77,215 80,478 83,231 85,243 90,181 95,447 105,480 115,296 125,325 135,457 145,481 155,341 165,365 175,463 183,981 195,369

1,64 1,80 3,04 2,13 1,66 2,03 2,41 1,81 1,67 1,96 1,66 1,79 1,91 1,67 2,41 1,91 2,05 1,68 2,25 1,88 1,69 1,77 1,86 1,70 1,85 1,95 1,70 1,84 2,04 1,76 1,83 2,00 1,89 1,82 1,71 1,80 1,90 1,79 1,72 1,78 1,85 1,78 1,75 1,77

15 11 9,0 10 12 9,0 8,0 10 10 9,0 10 9,0 8,0 10 8,0 8,0 8,0 9,0 8,0 8,0 9,0 9,0 8,0 9,0 8,0 8,0 9,0 8,0 8,0 8,0 8,0 8,0 8,0 8,0 8,0 8,0 8,0 8,0 8,0 8,0 8,0 8,0 8,0 8,0

54,521 48,316 47,335 50,447 56,413 51,497 52,967 59,393 60,090 59,797 63,660 65,139 65,470 71,967 68,288 69,932 72,791 77,722 76,329 78,001 82,163 85,115 86,058 90,273 89,803 93,257 98,368 97,877 100,414 102,993 105,939 108,435 113,123 118,217 127,969 138,115 148,507 158,332 168,127 178,247 188,549 198,404 208,229 218,331

1,02 1,09 1,25 1,19 1,11 1,23 1,36 1,21 1,20 1,28 1,21 1,29 1,37 1,24 1,46 1,39 1,43 1,31 1,48 1,42 1,33 1,35 1,44 1,35 1,44 1,49 1,37 1,46 1,53 1,45 1,48 1,54 1,52 1,50 1,47 1,53 1,59 1,55 1,52 1,57 1,62 1,58 1,55 1,59

a

Number of Nominal teeth dimension measured

k 2 2 2 2 2 2 2 2 3 3 3 3 3 3 3 3 3 3 3 3 4 4 4 4 4 4 4 4 4 5 5 4 5 5 6 6 6 7 7 8 8 8 9 9

a

a a a

a a a

a

a a a

a a a

Wk 19,241 18,928 18,114 18,614 19,614 18,800 18,486 19,486 30,869 30,055 31,055 30,741 30,428 31,428 29,614 30,614 30,300 31,800 29,986 30,986 42,869 42,555 42,241 43,241 42,428 42,114 43,614 42,800 41,986 54,369 54,055 42,359 53,928 54,614 66,869 66,428 65,986 78,241 79,614 90,055 89,614 90,986 103,241 102,800

These tooth thickness measurements are not reliable because they were made near the root fillet or the edge of the tip. Measurements between and over measuring circles are preferable. Deviations and tolerances can result in the unreliability of other tooth thickness measurements not identified by a.

31

SUPPLIED BY BSB UNDER LICENCE FROM DIN FOR ESCORTS LIMITED - FARIDABAD ON 29/12/2012

Basic data

DIN 5480-2:2006-05

16 Module m = 5 mm Table 26 — Nominal dimensions, m = 5 mm Dimensions in mm

Refer- Numence ber of diameter teeth

Pitch diameter

Base diameter

Shaft Space width addendum Tooth modification thickness

Hub diameter Root diameter

Deviation

Root form circle diameter

dFf2

Shaft diameter Tip diameter

Tip diameter

Root form circle diameter

dFf1

Root Deviation diameter

dB

z

d

db

x1 ⋅ m

e2 = s1

df2

Adf2

min.

da2

da1

max.

df1

Adf1

40 42 45 47 48 50 52 55 58 60 62 65 68 70 72 75 75 78 80 82 85 85 88 90 92 95 98 100 105 110 120 130 140 150 160 170 180 190 200 210 220 240 250 260 280 300 320

6 7 7 8 8 8 9 9 10 10 11 11 12 12 13 13 14 a 14 14 15 15 16 a 16 16 17 18 18 18 20 20 22 24 26 28 30 32 34 36 38 40 42 46 48 50 54 58 62

30 35 35 40 40 40 45 45 50 50 55 55 60 60 65 65 70 70 70 75 75 80 80 80 85 90 90 90 100 100 110 120 130 140 150 160 170 180 190 200 210 230 240 250 270 290 310

25,981 30,311 30,311 34,641 34,641 34,641 38,971 38,971 43,301 43,301 47,631 47,631 51,962 51,962 56,292 56,292 60,622 60,622 60,622 64,952 64,952 69,282 69,282 69,282 73,612 77,942 77,942 77,942 86,603 86,603 95,263 103,923 112,583 121,244 129,904 138,564 147,224 155,885 164,545 173,205 181,865 199,186 207,846 216,506 233,827 251,147 268,468

2,25 0,75 2,25 0,75 1,25 2,25 0,75 2,25 1,25 2,25 0,75 2,25 1,25 2,25 0,75 2,25 –0,25 1,25 2,25 0,75 2,25 –0,25 1,25 2,25 0,75 –0,25 1,25 2,25 –0,25 2,25 2,25 2,25 2,25 2,25 2,25 2,25 2,25 2,25 2,25 2,25 2,25 2,25 2,25 2,25 2,25 2,25 2,25

10,452 8,720 10,452 8,720 9,297 10,452 8,720 10,452 9,297 10,452 8,720 10,452 9,297 10,452 8,720 10,452 7,565 9,297 10,452 8,720 10,452 7,565 9,297 10,452 8,720 7,565 9,297 10,452 7,565 10,452 10,452 10,452 10,452 10,452 10,452 10,452 10,452 10,452 10,452 10,452 10,452 10,452 10,452 10,452 10,452 10,452 10,452

40 42 45 47 48 50 52 55 58 60 62 65 68 70 72 75 75 78 80 82 85 85 88 90 92 95 98 100 105 110 120 130 140 150 160 170 180 190 200 210 220 240 250 260 280 300 320

1,14 1,14 1,14 1,14 1,14 1,14 1,16 1,16 1,16 1,16 1,16 1,16 1,16 1,16 1,16 1,16 1,16 1,16 1,16 1,16 1,16 1,16 1,16 1,16 1,16 1,16 1,16 1,16 1,17 1,17 1,17 1,17 1,17 1,17 1,17 1,17 1,17 1,17 1,17 1,19 1,19 1,19 1,19 1,19 1,19 1,19 1,19

39,08 41,08 44,08 46,08 47,08 49,08 51,09 54,09 57,09 59,09 61,09 64,09 67,09 69,09 71,09 74,09 74,09 77,09 79,09 81,09 84,09 84,09 87,09 89,09 91,09 94,09 97,09 99,09 104,10 109,10 119,10 129,10 139,10 149,10 159,10 169,10 179,10 189,10 199,10 209,11 219,11 239,11 249,11 259,11 279,11 299,11 319,11

30 32 35 37 38 40 42 45 48 50 52 55 58 60 62 65 65 68 70 72 75 75 78 80 82 85 88 90 95 100 110 120 130 140 150 160 170 180 190 200 210 230 240 250 270 290 310

39 41 44 46 47 49 51 54 57 59 61 64 67 69 71 74 74 77 79 81 84 84 87 89 91 94 97 99 104 109 119 129 139 149 159 169 179 189 199 209 219 239 249 259 279 299 319

29,92 31,92 34,92 36,92 37,92 39,92 41,91 44,91 47,91 49,91 51,91 54,91 57,91 59,91 61,91 64,91 64,91 67,91 69,91 71,91 74,91 74,91 77,91 79,91 81,91 84,91 87,91 89,91 94,90 99,90 109,90 119,90 129,90 139,90 149,90 159,90 169,90 179,90 189,90 199,89 209,89 229,89 239,89 249,89 269,89 289,89 309,89

29,00 31,00 34,00 36,00 37,00 39,00 41,00 44,00 47,00 49,00 51,00 54,00 57,00 59,00 61,00 64,00 64,00 67,00 69,00 71,00 74,00 74,00 77,00 79,00 81,00 84,00 87,00 89,00 94,00 99,00 109,00 119,00 129,00 139,00 149,00 159,00 169,00 179,00 189,00 199,00 209,00 229,00 239,00 249,00 269,00 289,00 309,00

–1,49 –1,49 –1,49 –1,49 –1,49 –1,49 –1,55 –1,55 –1,55 –1,55 –1,55 –1,55 –1,55 –1,55 –1,55 –1,55 –1,55 –1,55 –1,55 –1,55 –1,55 –1,55 –1,55 –1,55 –1,55 –1,55 –1,55 –1,55 –1,62 –1,62 –1,62 –1,62 –1,62 –1,62 –1,62 –1,62 –1,62 –1,62 –1,62 –1,70 –1,70 –1,70 –1,70 –1,70 –1,70 –1,70 –1,70

a

32

A special tool is required for manufacturing splined hubs by shaping.

SUPPLIED BY BSB UNDER LICENCE FROM DIN FOR ESCORTS LIMITED - FARIDABAD ON 29/12/2012

Nominal dimensions

Basic data

DIN 5480-2:2006-05

Table 27 — Inspection dimensions, m = 5 mm Dimensions in mm Reference diameter

a

Hub dimensions

Number of teeth

Measuring circle diameter

dB

z

40 42 45 47 48 50 52 55 58 60 62 65 68 70 72 75 75 78 80 82 85 85 88 90 92 95 98 100 105 110 120 130 140 150 160 170 180 190 200 210 220 240 250 260 280 300 320

6 7 7 8 8 8 9 9 10 10 11 11 12 12 13 13 14 14 14 15 15 16 16 16 17 18 18 18 20 20 22 24 26 28 30 32 34 36 38 40 42 46 48 50 54 58 62

Shaft dimensions

Nominal dimension

Deviation factor

Measuring circle diameter

DM

M2

A*M2

9,0 9,0 9,0 9,0 9,0 9,0 9,0 9,0 9,0 9,0 9,0 9,0 9,0 9,0 9,0 9,0 9,0 9,0 9,0 9,0 9,0 9,0 9,0 9,0 9,0 9,0 9,0 9,0 9,0 9,0 9,0 9,0 9,0 9,0 9,0 9,0 9,0 9,0 9,0 9,0 9,0 9,0 9,0 9,0 9,0 9,0 9,0

21,103 21,573 25,223 27,554 28,922 31,103 32,028 35,418 38,968 41,103 42,254 45,542 48,996 51,103 52,398 55,629 55,235 59,014 61,103 62,498 65,692 65,416 69,027 71,103 72,573 75,531 79,036 81,103 85,613 91,103 101,103 111,103 121,103 131,103 141,103 151,103 161,103 171,103 181,103 191,103 201,103 221,103 231,103 241,103 261,103 281,103 301,103

1,71 3,29 1,67 2,71 2,13 1,72 2,41 1,69 2,01 1,72 2,19 1,70 1,95 1,72 2,08 1,71 2,62 1,91 1,72 2,01 1,72 2,37 1,88 1,73 1,96 2,24 1,86 1,73 2,15 1,73 1,73 1,73 1,73 1,73 1,73 1,73 1,73 1,73 1,73 1,73 1,73 1,73 1,73 1,73 1,73 1,73 1,73

Number of Nominal teeth dimension measured

Nominal dimension

Deviation factor

DM

M1

A*M1

k

18 12 16 12 12 14 11 14 12 14 11 12 11 12 10 12 10 11 12 10 12 10 10 11 10 10 10 11 10 11 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10

66,516 55,246 66,185 61,519 62,214 68,226 63,404 72,552 72,502 78,660 73,752 78,376 80,236 84,186 81,440 88,738 85,360 90,386 94,408 91,603 99,025 95,411 97,908 102,069 101,731 105,453 107,987 112,200 115,488 122,313 129,780 139,848 149,908 159,961 170,009 180,051 190,090 200,126 210,158 220,188 230,215 250,264 260,286 270,307 290,343 310,376 330,405

1,03 1,16 1,04 1,21 1,20 1,13 1,25 1,13 1,24 1,17 1,30 1,22 1,31 1,25 1,38 1,25 1,46 1,34 1,28 1,41 1,29 1,48 1,41 1,33 1,43 1,50 1,43 1,36 1,52 1,38 1,43 1,44 1,46 1,47 1,48 1,49 1,50 1,51 1,52 1,53 1,54 1,55 1,55 1,56 1,57 1,58 1,59

2 2 2 2 2 2 2 2 2 3 2 3 3 3 3 3 3 3 3 3 3 3 3 4 3 3 4 4 4 4 5 5 5 6 6 6 7 7 7 8 8 9 9 9 10 11 11

Wk

a a a a a

a a a a a a

a

a

a

a

a

a

24,052 22,784 24,284 23,017 23,517 24,517 23,250 24,750 23,983 38,586 23,716 38,819 38,052 39,052 37,784 39,284 37,017 38,517 39,517 38,250 39,750 37,483 38,983 53,586 38,716 37,948 53,052 54,052 52,017 54,517 68,586 69,052 69,517 83,586 84,052 84,517 98,586 99,052 99,517 113,586 114,052 128,586 129,052 129,517 144,052 158,586 159,517

These tooth thickness measurements are not reliable because they were made near the root fillet or the edge of the tip. Measurements between and over measuring circles are preferable. Deviations and tolerances can result in the unreliability of other tooth thickness measurements not identified by a.

33

SUPPLIED BY BSB UNDER LICENCE FROM DIN FOR ESCORTS LIMITED - FARIDABAD ON 29/12/2012

Basic data

DIN 5480-2:2006-05

17 Module m = 6 mm Table 28 — Nominal dimensions, m = 6 mm Dimensions in mm

Refer- Numence ber of diameter teeth

Pitch diameter

Base diameter

Hub diameter

Shaft Space width Root addendum Tooth diammodification thickness eter

Deviation

Root form circle diameter

dB

z

d

db

x1 ⋅ m

e2 = s1

df2

Adf2

dFf2 min.

48 50 52 55 58 60 62 65 68 70 72 75 78 78 80 82 85 88 90 90 92 95 98 100 105 110 120 130 140 150 160 170 180 190 200 210 220 240 250 260 280 300 320 340 360 380 400 420 440 450 460 480 500

6 7 7 8 8 8 9 9 10 10 10 11 11 12 a 12 12 13 13 13 14 a 14 14 15 15 16 17 18 20 22 24 25 27 28 30 32 34 35 38 40 42 45 48 52 55 58 62 65 68 72 74 75 78 82

36 42 42 48 48 48 54 54 60 60 60 66 66 72 72 72 78 78 78 84 84 84 90 90 96 102 108 120 132 144 150 162 168 180 192 204 210 228 240 252 270 288 312 330 348 372 390 408 432 444 450 468 492

31,177 36,373 36,373 41,569 41,569 41,569 46,765 46,765 51,962 51,962 51,962 57,158 57,158 62,354 62,354 62,354 67,550 67,550 67,550 72,746 72,746 72,746 77,942 77,942 83,138 88,335 93,531 103,923 114,315 124,708 129,904 140,296 145,492 155,885 166,277 176,669 181,865 197,454 207,846 218,238 233,827 249,415 270,200 285,788 301,377 322,161 337,750 353,338 374,123 384,515 389,711 405,300 426,084

2,7 0,7 1,7 0,2 1,7 2,7 0,7 2,2 0,7 1,7 2,7 1,2 2,7 –0,3 0,7 1,7 0,2 1,7 2,7 –0,3 0,7 2,2 0,7 1,7 1,2 0,7 2,7 1,7 0,7 –0,3 1,7 0,7 2,7 1,7 0,7 –0,3 1,7 2,7 1,7 0,7 1,7 0,7 0,7 1,7 2,7 0,7 1,7 2,7 0,7 –0,3 1,7 2,7 0,7

12,542 10,233 11,388 9,656 11,388 12,542 10,233 11,965 10,233 11,388 12,542 10,810 12,542 9,078 10,233 11,388 9,656 11,388 12,542 9,078 10,233 11,965 10,233 11,388 10,810 10,233 12,542 11,388 10,233 9,078 11,388 10,233 12,542 11,388 10,233 9,078 11,388 12,542 11,388 10,233 11,388 10,233 10,233 11,388 12,542 10,233 11,388 12,542 10,233 9,078 11,388 12,542 10,233

48 50 52 55 58 60 62 65 68 70 72 75 78 78 80 82 85 88 90 90 92 95 98 100 105 110 120 130 140 150 160 170 180 190 200 210 220 240 250 260 280 296 320 340 360 380 400 420 440 450 460 480 500

1,34 1,34 1,36 1,36 1,36 1,36 1,36 1,36 1,36 1,36 1,36 1,36 1,36 1,36 1,36 1,36 1,36 1,36 1,36 1,36 1,36 1,36 1,36 1,36 1,37 1,37 1,37 1,37 1,37 1,37 1,37 1,37 1,37 1,37 1,37 1,39 1,39 1,39 1,39 1,39 1,39 1,39 1,39 1,39 1,39 1,39 1,39 1,42 1,42 1,42 1,42 1,42 1,42

46,88 48,88 50,89 53,89 56,89 58,89 60,89 63,89 66,89 68,89 70,89 73,89 76,89 76,89 78,89 80,89 83,89 86,89 88,89 88,89 90,89 93,89 96,89 98,89 103,90 108,90 118,90 128,90 138,90 148,90 158,90 168,90 178,90 188,90 198,90 208,91 218,91 238,91 248,91 258,91 278,91 294,91 318,91 338,91 358,91 378,91 398,91 418,93 438,93 448,93 458,93 478,93 498,93

a

34

A special tool is required for manufacturing splined hubs by shaping.

Shaft diameter Root form circle diameter

Tip diameter

Tip diameter

da2

da1

dFf1 max.

36 38 40 43 46 48 50 53 56 58 60 63 66 66 68 70 73 76 78 78 80 83 86 88 93 98 108 118 128 138 148 158 168 178 188 198 208 228 238 248 268 284 308 328 348 368 388 408 428 438 448 468 488

46,8 48,8 50,8 53,8 56,8 58,8 60,8 63,8 66,8 68,8 70,8 73,8 76,8 76,8 78,8 80,8 83,8 86,8 88,8 88,8 90,8 93,8 96,8 98,8 103,8 108,8 118,8 128,8 138,8 148,8 158,8 168,8 178,8 188,8 198,8 208,8 218,8 238,8 248,8 258,8 278,8 294,8 318,8 338,8 358,8 378,8 398,8 418,8 438,8 448,8 458,8 478,8 498,8

35,92 37,92 39,91 42,91 45,91 47,91 49,91 52,91 55,91 57,91 59,91 62,91 65,91 65,91 67,91 69,91 72,91 75,91 77,91 77,91 79,91 82,91 85,91 87,91 92,90 97,90 107,90 117,90 127,90 137,90 147,90 157,90 167,90 177,90 187,90 197,89 207,89 227,89 237,89 247,89 267,89 283,89 307,89 327,89 347,89 367,89 387,89 407,87 427,87 437,87 447,87 467,87 487,87

Root diameter

Deviation

df1

Adf1

34,80 36,80 38,80 41,80 44,80 46,80 48,80 51,80 54,80 56,80 58,80 61,80 64,80 64,80 66,80 68,80 71,80 74,80 76,80 76,80 78,80 81,80 84,80 86,80 91,80 96,80 106,80 116,80 126,80 136,80 146,80 156,80 166,80 176,80 186,80 196,80 206,80 226,80 236,80 246,80 266,80 282,80 306,80 326,80 346,80 366,80 386,80 406,80 426,80 436,80 446,80 466,80 486,80

–1,69 –1,69 –1,75 –1,75 –1,75 –1,75 –1,75 –1,75 –1,75 –1,75 –1,75 –1,75 –1,75 –1,75 –1,75 –1,75 –1,75 –1,75 –1,75 –1,75 –1,75 –1,75 –1,75 –1,75 –1,82 –1,82 –1,82 –1,82 –1,82 –1,82 –1,82 –1,82 –1,82 –1,82 –1,82 –1,90 –1,90 –1,90 –1,90 –1,90 –1,90 –1,90 –1,90 –1,90 –1,90 –1,90 –1,90 –1,98 –1,98 –1,98 –1,98 –1,98 –1,98

SUPPLIED BY BSB UNDER LICENCE FROM DIN FOR ESCORTS LIMITED - FARIDABAD ON 29/12/2012

Nominal dimensions

Basic data

DIN 5480-2:2006-05

Table 29 — Inspection dimensions, m = 6 mm Dimensions in mm Hub dimensions

Shaft dimensions

Reference diameter

Number of teeth

Measuring circle diameter

Nominal dimension

Deviation factor

dB

z

DM

M2

A *M2

DM

48 50 52 55 58 60 62 65 68 70 72 75 78 78 80 82 85 88 90 90 92 95 98 100 105 110 120 130 140 150 160 170 180 190 200 210 220 240 250 260 280 300 320 340 360 380 400 420 440 450 460 480 500

6 7 7 8 8 8 9 9 10 10 10 11 11 12 12 12 13 13 13 14 14 14 15 15 16 17 18 20 22 24 25 27 28 30 32 34 35 38 40 42 45 48 52 55 58 62 65 68 72 74 75 78 82

10,5 10 10,5 10 10,5 10,5 10,5 10,5 10,5 10,5 10,5 10,5 10,5 10,5 10,5 10,5 10,5 10,5 10,5 10,5 10,5 10,5 10,5 10,5 10,5 10,5 10,5 10,5 10,5 10,5 10,5 10,5 10,5 10,5 10,5 10,5 10,5 10,5 10,5 10,5 10,5 10,5 11 11 11 11 11 11 11 11 11 11 11

26,204 28,471 29,136 34,169 36,165 38,209 39,007 42,406 45,839 48,178 50,212 52,433 55,534 55,200 57,928 60,187 62,185 65,631 67,641 67,451 69,982 73,223 75,529 77,709 83,132 87,614 98,217 108,203 118,084 127,864 137,914 147,845 158,220 168,210 178,132 187,988 198,002 218,221 228,214 238,156 258,051 278,221 296,630 316,566 336,724 356,646 376,590 396,724 416,657 426,581 436,608 456,724 476,666

1,64 2,18 1,89 2,56 1,91 1,66 2,32 1,73 2,24 1,86 1,67 1,96 1,66 2,75 2,10 1,84 2,23 1,82 1,67 2,41 2,02 1,75 1,99 1,80 1,88 1,95 1,70 1,79 1,89 2,00 1,78 1,85 1,71 1,77 1,83 1,90 1,76 1,72 1,76 1,81 1,76 1,72 1,81 1,77 1,74 1,80 1,76 1,74 1,79 1,81 1,76 1,74 1,78

22 14 16 12 16 18 14 16 14 14 16 14 15 12 12 14 12 14 14 12 12 14 12 12 12 12 14 12 12 12 12 12 12 12 12 12 12 12 12 12 12 12 11 11 11 11 11 11 11 11 11 11 11

a

Deviation factor

Number of teeth measured

M1

A *M1

k

80,692 65,089 71,023 66,901 78,701 84,619 77,745 84,551 84,861 86,315 92,509 90,930 95,491 90,355 91,978 98,580 96,601 104,032 105,505 102,431 104,088 111,549 109,597 111,211 117,001 121,745 136,686 141,997 152,367 162,653 171,846 182,184 191,953 202,282 212,550 222,760 232,152 252,190 262,447 272,658 292,335 312,343 329,859 349,607 369,617 389,891 409,675 429,677 449,915 459,993 469,725 489,723 509,933

1,02 1,17 1,10 1,33 1,16 1,11 1,23 1,15 1,27 1,25 1,18 1,27 1,21 1,43 1,38 1,28 1,41 1,29 1,26 1,46 1,41 1,30 1,42 1,38 1,42 1,44 1,34 1,44 1,49 1,54 1,48 1,52 1,47 1,51 1,55 1,59 1,53 1,52 1,55 1,58 1,57 1,55 1,63 1,61 1,60 1,65 1,63 1,61 1,66 1,68 1,64 1,63 1,66

2 2 2 2 2 2 2 2 2 2 3 3 3 2 3 3 3 3 3 3 3 3 3 3 3 3 4 4 4 4 5 5 6 6 6 6 7 7 7 8 8 9 9 10 11 11 12 12 13 13 13 14 14

Measuring circle Nominal diameter dimension

Nominal dimension

Wk

a a a a a a

a a a

a

a a a a

a

a a

28,862 27,141 28,141 26,921 28,421 29,421 27,700 29,200 27,979 28,979 46,303 45,083 46,583 27,538 44,862 45,862 44,641 46,141 47,141 44,421 45,421 46,921 45,700 46,700 46,479 46,259 64,862 64,421 63,979 63,538 82,141 81,700 100,303 99,862 99,421 98,979 117,583 119,421 118,979 134,862 136,700 154,862 153,979 172,141 190,303 189,421 207,583 209,421 224,862 224,421 226,700 244,862 243,979

These tooth thickness measurements are not reliable because they were made near the root fillet or the edge of the tip. Measurements between and over measuring circles are preferable. Deviations and tolerances can result in the unreliability of other a tooth thickness measurements not identified by .

35

SUPPLIED BY BSB UNDER LICENCE FROM DIN FOR ESCORTS LIMITED - FARIDABAD ON 29/12/2012

Basic data

DIN 5480-2:2006-05

18 Module m = 8 mm Table 30 — Nominal dimensions, m = 8 mm Dimensions in mm

Refer- Number of ence diameter teeth

Pitch diameter

Base diameter

Space width Shaft Tooth addendum modification thickness

Hub diameter Root diameter

Deviation

Root form circle diameter

dFf2

Shaft diameter Tip diameter

Tip diameter

Root form circle diameter

dFf1

Root diameter

Deviation

dB

z

d

db

x1 ⋅ m

e2 = s1

df2

Adf2

min.

da2

da1

max.

df1

Adf1

60 65 70 75 80 85 90 95 100 105 110 120 120 130 140 150 160 170 180 190 200 210 220 240 250 260 280 300 320 340 360 380 400 420 440 450 460 480 500

6 7 7 8 8 9 10 10 11 12 12 13 14 a 15 16 17 18 20 21 22 24 25 26 28 30 31 34 36 38 41 44 46 48 51 54 55 56 58 61

48 56 56 64 64 72 80 80 88 96 96 104 112 120 128 136 144 160 168 176 192 200 208 224 240 248 272 288 304 328 352 368 384 408 432 440 448 464 488

41,569 48,497 48,497 55,426 55,426 62,354 69,282 69,282 76,210 83,138 83,138 90,067 96,995 103,923 110,851 117,779 124,708 138,564 145,492 152,420 166,277 173,205 180,133 193,990 207,846 214,774 235,559 249,415 263,272 284,056 304,841 318,697 332,554 353,338 374,123 381,051 387,979 401,836 422,620

1,6 0,1 2,6 1,1 3,6 2,1 0,6 3,1 1,6 0,1 2,6 3,6 –0,4 0,6 1,6 2,6 3,6 0,6 1,6 2,6 –0,4 0,6 1,6 3,6 0,6 1,6 –0,4 1,6 3,6 1,6 –0,4 1,6 3,6 1,6 –0,4 0,6 1,6 3,6 1,6

14,414 12,682 15,569 13,837 16,723 14,991 13,259 16,146 14,414 12,682 15,569 16,723 12,104 13,259 14,414 15,569 16,723 13,259 14,414 15,569 12,104 13,259 14,414 16,723 13,259 14,414 12,104 14,414 16,723 14,414 12,104 14,414 16,723 14,414 12,104 13,259 14,414 16,723 14,414

60 65 70 75 80 85 90 95 100 105 110 120 120 130 140 150 160 170 180 190 200 210 220 240 250 260 280 300 320 340 360 380 400 420 440 450 460 480 500

1,76 1,76 1,76 1,76 1,76 1,76 1,76 1,76 1,76 1,77 1,77 1,77 1,77 1,77 1,77 1,77 1,77 1,77 1,77 1,77 1,77 1,79 1,79 1,79 1,79 1,79 1,79 1,79 1,79 1,79 1,79 1,79 1,79 1,82 1,82 1,82 1,82 1,82 1,82

58,49 63,49 68,49 73,49 78,49 83,49 88,49 93,49 98,49 103,50 108,50 118,50 118,50 128,50 138,50 148,50 158,50 168,50 178,50 188,50 198,50 208,51 218,51 238,51 248,51 258,51 278,51 298,51 318,51 338,51 358,51 378,51 398,51 418,53 438,53 448,53 458,53 478,53 498,53

44 49 54 59 64 69 74 79 84 89 94 104 104 114 124 134 144 154 164 174 184 194 204 224 234 244 264 284 304 324 344 364 384 404 424 434 444 464 484

58,4 63,4 68,4 73,4 78,4 83,4 88,4 93,4 98,4 103,4 108,4 118,4 118,4 128,4 138,4 148,4 158,4 168,4 178,4 188,4 198,4 208,4 218,4 238,4 248,4 258,4 278,4 298,4 318,4 338,4 358,4 378,4 398,4 418,4 438,4 448,4 458,4 478,4 498,4

43,91 48,91 53,91 58,91 63,91 68,91 73,91 78,91 83,91 88,90 93,90 103,90 103,90 113,90 123,90 133,90 143,90 153,90 163,90 173,90 183,90 193,89 203,89 223,89 233,89 243,89 263,89 283,89 303,89 323,89 343,89 363,89 383,89 403,87 423,87 433,87 443,87 463,87 483,87

42,40 47,40 52,40 57,40 62,40 67,40 72,40 77,40 82,40 87,40 92,40 102,40 102,40 112,40 122,40 132,40 142,40 152,40 162,40 172,40 182,40 192,40 202,40 222,40 232,40 242,40 262,40 282,40 302,40 322,40 342,40 362,40 382,40 402,40 422,40 432,40 442,40 462,40 482,40

–2,15 –2,15 –2,15 –2,15 –2,15 –2,15 –2,15 –2,15 –2,15 –2,22 –2,22 –2,22 –2,22 –2,22 –2,22 –2,22 –2,22 –2,22 –2,22 –2,22 –2,22 –2,30 –2,30 –2,30 –2,30 –2,30 –2,30 –2,30 –2,30 –2,30 –2,30 –2,30 –2,30 –2,38 –2,38 –2,38 –2,38 –2,38 –2,38

a

36

A special tool is required for manufacturing splined hubs by shaping.

SUPPLIED BY BSB UNDER LICENCE FROM DIN FOR ESCORTS LIMITED - FARIDABAD ON 29/12/2012

Nominal dimensions

Basic data

DIN 5480-2:2006-05

Table 31 — Inspection dimensions, m = 8 mm Dimensions in mm Hub dimensions

Shaft dimensions

Reference diameter

Number of teeth

Measuring circle diameter

Nominal dimension

Deviation factor

Measuring circle diameter

Nominal dimension

Deviation factor

dB

z

DM

M2

A *M2

DM

M1

A *M1

60

6

14

30,516

2,42

22

88,848

1,11

65

7

13b

36,924

2,63

16

79,195

70 75 80 85 90 95 100 105 110 120 120 130 140 150 160 170 180 190 200 210 220 240 250 260 280 300 320 340 360 380 400 420 440 450 460 480 500

7 8 8 9 10 10 11 12 12 13 14 15 16 17 18 20 21 22 24 25 26 28 30 31 34 36 38 41 44 46 48 51 54 55 56 58 61

14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14

39,557 45,371 50,945 54,803 60,225 65,966 69,911 75,080 80,948 90,188 89,935 99,929 110,843 120,378 130,956 140,681 150,414 160,956 170,486 180,363 190,894 210,959 220,788 230,592 250,650 270,915 290,961 310,683 330,731 350,926 370,962 390,738 410,778 420,697 430,934 450,963 470,776

1,80 2,42 1,66 1,89 2,41 1,73 1,96 2,41 1,79 1,67 2,41 2,05 1,88 1,77 1,70 1,95 1,84 1,76 2,00 1,89 1,82 1,71 1,86 1,80 1,90 1,79 1,72 1,78 1,85 1,78 1,72 1,77 1,83 1,80 1,77 1,72 1,77

22 18 22 20 16 20 18 16 18 20 16 16 16 18 18 16 16 16 16 16 16 16 16 16 16 16 16 16 16 16 16 16 16 16 16 16 16

96,632 95,390 108,241 108,481 105,933 119,486 119,594 121,294 130,279 143,934 136,575 145,582 156,001 170,231 180,546 186,514 195,753 205,987 216,870 226,246 236,435 255,937 266,768 276,230 297,014 316,665 336,253 356,494 377,099 396,808 416,458 436,662 457,155 466,855 476,906 496,602 516,779

Number of Nominal teeth dimension measured

k

Wk

2

36,483

1,27

2

35,355

1,09 1,24 1,13 1,18 1,36 1,21 1,28 1,41 1,29 1,24 1,46 1,43 1,42 1,35 1,35 1,49 1,46 1,45 1,54 1,52 1,50 1,47 1,55 1,53 1,59 1,55 1,52 1,57 1,62 1,58 1,55 1,59 1,63 1,62 1,60 1,58 1,61

2 2 2 2 2 3 3 3 3 3 3 3 3 4 4 4 4 5 4 5 5 6 6 6 6 7 7 8 8 8 9 9 9 10 10 11 11

37,855 36,728 39,228 38,100 36,972 61,238 60,110 58,983 61,483 62,855 59,228 60,600 61,972 85,110 86,483 84,228 85,600 108,738 84,717 107,855 109,228 133,738 131,483 132,855 131,972 156,483 159,228 180,110 179,228 181,972 206,483 205,600 204,717 227,855 229,228 253,738 252,855

a

a a a

a

a a

a a

a

a

a

These tooth thickness measurements are not reliable because they were made near the root fillet or the edge of the tip. Measurements between and over measuring circles are preferable. Deviations and tolerances can result in the unreliability of other tooth thickness measurements not identified by a.

b

Not specified in DIN 3977.

37

SUPPLIED BY BSB UNDER LICENCE FROM DIN FOR ESCORTS LIMITED - FARIDABAD ON 29/12/2012

Basic data

DIN 5480-2:2006-05

19 Module m = 10 mm Table 32 — Nominal dimensions, m = 10 mm Dimensions in mm

Refer- Numence ber of diameter teeth

Pitch diameter

Base diameter

Shaft Space width addendum Tooth modification thickness

Hub diameter Root diameter

Deviation

Root form circle diameter

dFf2

Shaft diameter Tip diameter

Tip diameter

Root form circle diameter

dFf1

Root Deviation diameter

dB

z

d

db

x1 ⋅ m

e2 = s1

df2

Adf2

min.

da2

da1

max.

df1

Adf1

80 85 90 95 100 105 110 120 130 130 140 150 150 160 170 170 180 190 190 200 210 220 240 250 260 280 300 320 340 360 380 400 420 440 450 460 480 500

6 7 7 8 8 9 9 10 11 12 a 12 13 14 a 14 15 16 a 16 17 18 a 18 20 a 20 22 24 24 26 28 30 32 34 36 38 40 42 44 44 46 48

60 70 70 80 80 90 90 100 110 120 120 130 140 140 150 160 160 170 180 180 200 200 220 240 240 260 280 300 320 340 360 380 400 420 440 440 460 480

51,962 60,622 60,622 69,282 69,282 77,942 77,942 86,603 95,263 103,923 103,923 112,583 121,244 121,244 129,904 138,564 138,564 147,224 155,885 155,885 173,205 173,205 190,526 207,846 207,846 225,167 242,487 259,808 277,128 294,449 311,769 329,090 346,410 363,731 381,051 381,051 398,372 415,692

4,5 2 4,5 2 4,5 2 4,5 4,5 4,5 –0,5 4,5 4,5 –0,5 4,5 4,5 –0,5 4,5 4,5 –0,5 4,5 –0,5 4,5 4,5 –0,5 4,5 4,5 4,5 4,5 4,5 4,5 4,5 4,5 4,5 4,5 –0,5 4,5 4,5 4,5

20,904 18,017 20,904 18,017 20,904 18,017 20,904 20,904 20,904 15,131 20,904 20,904 15,131 20,904 20,904 15,131 20,904 20,904 15,131 20,904 15,131 20,904 20,904 15,131 20,904 20,904 20,904 20,904 20,904 20,904 20,904 20,904 20,904 20,904 15,131 20,904 20,904 20,904

80 85 90 95 100 105 110 120 130 130 140 150 150 160 170 170 180 190 190 200 210 220 240 250 260 280 300 320 340 360 380 400 420 440 450 460 480 500

2,16 2,16 2,16 2,16 2,16 2,17 2,17 2,17 2,17 2,17 2,17 2,17 2,17 2,17 2,17 2,17 2,17 2,17 2,17 2,17 2,19 2,19 2,19 2,19 2,19 2,19 2,19 2,19 2,19 2,19 2,19 2,19 2,22 2,22 2,22 2,22 2,22 2,22

78,09 83,09 88,09 93,09 98,09 103,10 108,10 118,10 128,10 128,10 138,10 148,10 148,10 158,10 168,10 168,10 178,10 188,10 188,10 198,10 208,11 218,11 238,11 248,11 258,11 278,11 298,11 318,11 338,11 358,11 378,11 398,11 418,13 438,13 448,13 458,13 478,13 498,13

60 65 70 75 80 85 90 100 110 110 120 130 130 140 150 150 160 170 170 180 190 200 220 230 240 260 280 300 320 340 360 380 400 420 430 440 460 480

78 83 88 93 98 103 108 118 128 128 138 148 148 158 168 168 178 188 188 198 208 218 238 248 258 278 298 318 338 358 378 398 418 438 448 458 478 498

59,91 64,91 69,91 74,91 79,91 84,90 89,90 99,90 109,90 109,90 119,90 129,90 129,90 139,90 149,90 149,90 159,90 169,90 169,90 179,90 189,89 199,89 219,89 229,89 239,89 259,89 279,89 299,89 319,89 339,89 359,89 379,89 399,87 419,87 429,87 439,87 459,87 479,87

58,00 63,00 68,00 73,00 78,00 83,00 88,00 98,00 108,00 108,00 118,00 128,00 128,00 138,00 148,00 148,00 158,00 168,00 168,00 178,00 188,00 198,00 218,00 228,00 238,00 258,00 278,00 298,00 318,00 338,00 358,00 378,00 398,00 418,00 428,00 438,00 458,00 478,00

–2,55 –2,55 –2,55 –2,55 –2,55 –2,62 –2,62 –2,62 –2,62 –2,62 –2,62 –2,62 –2,62 –2,62 –2,62 –2,62 –2,62 –2,62 –2,62 –2,62 –2,70 –2,70 –2,70 –2,70 –2,70 –2,70 –2,70 –2,70 –2,70 –2,70 –2,70 –2,70 –2,78 –2,78 –2,78 –2,78 –2,78 –2,78

a

38

A special tool is required for manufacturing splined hubs by shaping.

SUPPLIED BY BSB UNDER LICENCE FROM DIN FOR ESCORTS LIMITED - FARIDABAD ON 29/12/2012

Nominal dimensions

Basic data

DIN 5480-2:2006-05

Table 33 — Inspection dimensions, m = 10 mm Dimensions in mm Hub dimensions

Shaft dimensions

Reference diameter

Number of teeth

Measuring circle diameter

Nominal dimension

Deviation factor

Measuring circle diameter

Nominal dimension

Deviation factor

dB

z

DM

M2

A *M2

DM

M1

A *M1

80 85 90 95 100 105 110 120 130 130 140 150 150 160 170 170 180 190 190 200 210 220 240 250 260 280 300 320 340 360 380 400 420 440 450 460 480 500

6 7 7 8 8 9 9 10 11 12 12 13 14 14 15 16 16 17 18 18 20 20 22 24 24 26 28 30 32 34 36 38 40 42 44 44 46 48

18 18 18 18 18 18 18 18 18 18 18 18 18 18 18 18 18 18 18 18 18 18 18 18 18 18 18 18 18 18 18 18 18 18 18 18 18 18

42,206 44,776 50,446 56,557 62,206 65,378 70,836 82,206 91,085 89,781 102,206 111,257 110,470 122,207 131,384 130,832 142,207 151,481 151,063 162,207 171,225 182,207 202,207 211,440 222,207 242,207 262,207 282,207 302,207 322,207 342,207 362,207 382,207 402,207 411,838 422,207 442,207 462,207

1,71 2,50 1,67 2,34 1,72 2,18 1,69 1,72 1,70 3,27 1,72 1,71 2,62 1,72 1,72 2,37 1,73 1,72 2,24 1,73 2,15 1,73 1,73 2,04 1,73 1,73 1,73 1,73 1,73 1,73 1,73 1,73 1,73 1,73 1,87 1,73 1,73 1,73

35 25 30 25 28 25 28 25 25 22 25 25 22 25 22 22 22 22 20 22 20 22 22 20 20 20 20 20 20 20 20 20 20 20 20 20 20 20

130,845 113,476 127,942 126,117 136,452 134,743 145,104 150,225 159,151 155,828 170,806 179,918 176,022 191,284 193,049 196,180 204,139 213,455 210,905 224,401 230,976 244,626 264,823 271,088 279,696 299,816 319,922 340,017 360,103 380,181 400,252 420,316 440,376 460,431 471,373 480,481 500,528 520,572

1,03 1,13 1,06 1,19 1,13 1,19 1,13 1,20 1,21 1,37 1,23 1,24 1,40 1,27 1,31 1,43 1,33 1,34 1,50 1,36 1,52 1,38 1,40 1,54 1,44 1,46 1,47 1,48 1,49 1,50 1,51 1,52 1,53 1,54 1,62 1,54 1,55 1,55

a

Number of teeth measured

Nominal dimension

k

Wk

2 2 2 2 2 2 2 3 3 2 3 3 3 3 3 3 4 4 3 4 4 4 5 4 5 5 6 6 6 7 7 7 8 8 8 8 9 9

a a a a

a a a a

a a a

a

a

a

48,103 46,069 48,569 46,534 49,034 47,000 49,500 77,172 77,638 45,897 78,103 78,569 74,034 79,034 79,500 74,966 107,172 107,638 75,897 108,103 104,034 109,034 137,172 105,897 138,103 139,034 167,172 168,103 169,034 197,172 198,103 199,034 227,172 228,103 224,034 229,034 257,172 258,103

The deviation values stated here relate to chip-cutting machining methods and the theoretical root diameter (see DIN 5480-1, 7.1). The deviation for cold-rolled splines is –0,76 ⋅ m.

39

SUPPLIED BY BSB UNDER LICENCE FROM DIN FOR ESCORTS LIMITED - FARIDABAD ON 29/12/2012

Basic data

DIN 5480-2:2006-05

Bibliography

DIN 323-1, Preferred numbers and series of preferred numbers — Basic values, calculated values, rounded values DIN 780-1, Module series for gears — Modules for cylindrical gears

DIN 3961, Tolerances for cylindrical gear teeth — Principles DIN 3977:1981-02, Measuring element diameters for the radial or diametral dimension for testing tooth thickness of cylindrical gears DIN 5466-1, Calculation of load capacityof splined joints — Part 1: Principles DIN ISO 6413:1990-03, Technical drawings — Representation of splines and serrations (ISO 6413:1988) ISO 54:1996-12, Cylindrical gears for general engineering and for heavy engineering — Modules ISO 4156 series, Straight cylindrical involute splines — Metric module, side fit

40

SUPPLIED BY BSB UNDER LICENCE FROM DIN FOR ESCORTS LIMITED - FARIDABAD ON 29/12/2012

DIN 3960, Concepts and parameters associated with cylindrical gears and cylindrical gear pairs with involute teeth