Cyclone Design Calculation Tool Simplified [PDF]

Zitiervorschau

Cyclone calculation tool

DO NOT USE THIS METHOD FOR DETAIL DESIGN – ALWAYS CONSULT A REPUTABLE SUPPLIER FOR DETAIL DESIGN Cyclone design tool

Gas flowrate Dust load Gas viscosty Gas density Solid density

To modify

Calculated

Dust stream to separate Vc 22500 23 μc 2.20E-05 0.8825 1500

m3/h g/m3 Pa.s kg/m3 kg/m3

Control panel Cyclone diameter Dc (m) 1 Please modify the cyclone dia Cut off diameter (microns) 3.1 Pressure drop 7979.3

Selection of Standard Geometry Please select one standard geometry and copy past the values in the «chosen geometry» table

Dimensions Hc/Dc = KH Bc/Dc = KB Sc/Dc = KS Di/Dc = Ki Lc/Dc = KL Zc/Dc = KZ DS/Dc = KD

Standard Geometries for cyclones with tangential inlet Standard High efficiency Peterson Whitby Stairmand Lapple Swift Swift 0.5 0.5 0.583 0.5 0.44 0.25 0.25 0.208 0.2 0.21 0.625 0.6 0.583 0.5 0.5 0.5 0.5 0.5 0.5 0.4 2 1.75 1.333 1.5 1.4 2 2 1.84 2.5 2.5 0.25 0.4 0.5 0.375 0.4 Calculation of the dimensions of the cyclone

Page 1

Cyclone calculation tool

If you spot a mistake or wish to suggest an improvement, please contact [email protected]

Page 2

Cyclone calculation tool Copyright www.PowderProcess.net

The content of PowderProcess.net is copyrighted but no warranty nor liability is ensured. The content of this site is to be seen as a help and important information and calcula quality procedure of his organization or by checking another source. The user must always respect all applicable regulation. The use of the information is at the u

Page 3

Cyclone calculation tool

PPLIER FOR DETAIL DESIGN

Control panel Cyclone diameter Dc (m) m Please modify the cyclone diameter until cut off diameter reaches target and low pressure drop Cut off diameter (microns) microns Pressure drop Pa

ometry» table

ensions of the cyclone Chosen geometry Dimensions Copy paste the standard geometry chosen from the table above

Hc/Dc = KH Bc/Dc = KB Sc/Dc = KS Di/Dc = Ki Lc/Dc = KL Zc/Dc = KZ DS/Dc = KD

0.5 0.2 0.5 0.5 1.5 2.5 0.375 Estimate Dc

Dc

1.0 m Calculation of the other dimensions

Page 4

Cyclone calculation tool Hc Bc Sc Di Lc Zc DS

0.5 m 0.2 m 0.5 m 0.5 m 1.5 m 2.5 m 0.4 m Geometrical ratio calculations

Ae/Ai Ri/re Ae/Ai*Ri/re Af/Ai

0.5 0.6 0.3 61.0 Inlet and outlet velocities

Uce Uci

62.5 m/s 31.8 Striction and friction coefficient

Ce Ucc/Uce Rec Cf

0.8 1.2 3105155.2 0.0 Characteristic velocities

Ucri Uctetai/Uci Uctetai

1.1 m/s 2.6 m/s 82.7 m/s Cut off diameter

dc

0.0 m 0.0 mm 3.1 microns Pressure drop

Af/PiRi(RCRi)^0.5 Rc Ri/re ksice ksici DPC

43.1 0.5 0.3 3.2 14.6 7979.3 Pa

[email protected]

Page 5

Cyclone calculation tool

a help and important information and calculation must always be double checked by the user through the gulation. The use of the information is at the user and its organization own risk and own cost.

Page 6