35 0 2MB
CORROSION PROTECTION Offshore installations
CORROSION PROTECTION Offshore installations
Contents
2
Introduction
3
Typical offshore specifications
5
Key offshore products
6
Documentation
7
Crucial performance indicators
8
Problems and solutions
9
Offshore product range
10
A lifetime protecting offshore structures For almost a century, Hempel has been providing high-quality
an extremely beneficial return on investment, dramatically
protective coating systems for stationary and floating steel
increasing the useful lifetime of all individual components
structures of all kinds. Today, some of the world’s longest
and keeping downtime to a minimum. And for anyone looking
bridges, tallest cranes and largest ships rely on Hempel
for a protection specification that will last up to 30 years,
quality to keep them working and looking their best. Not
second best is simply not good enough.
surprisingly, Hempel also provides protection for a vast number of offshore structures in some of the harshest
Technical expertise
environments in the world.
Our FROSIO/NACE-certified technical staff and coating advisers have in-depth knowledge and understanding of
High return on investment
on-site working procedures and the conditions under which
Owners and operators know that each floating production
paint contractors must operate. In fact, we’re one of the few
system – from full-scale platforms to FPSOs and barges
companies authorised to conduct in-house FROSIO training.
– represents a valuable asset as both a capital investment and a source of ongoing revenue. They also know that high-performance protective coatings from Hempel provide
3
1
3 7
2
6 4
5
4
4
Typical offshore specifications 1
Main exterior surfaces
Generic type Polyurethane or Polysiloxane Epoxy Epoxy Inorganic or organic zinc-rich
2
Main exterior decks, escape routes, heavy traffic and helidecks
Generic type Heavy-duty epoxy
3
Dry film thickness 25 µm / 1 mil 25 µm / 1 mil 200 µm / 8 mils
Tank lining
Generic type Epoxy phenolic Epoxy phenolic Epoxy phenolic
5
Dry film thickness 3000 µm / 120 mils
Hot surfaces
Generic type Silicone aluminium Silicone aluminium Thermal sprayed aluminium
4
Dry film thickness 50 µm / 2 mils or 100 µm / 4 mils 125 µm / 5 mils 125 µm / 5 mils 50 µm / 2 mils
Dry film thickness 100 µm / 4 mils 100 µm / 4 mils 100 µm / 4 mils
Splash zone and submerged surfaces
Generic type Glass flake epoxy Glass flake epoxy
Dry film thickness 500 µm / 20 mils 500 µm / 20 mils
e loxan Polysi ne ne or olysiloxa a th P re ne Polyu thanEepoorxyolysiloxxaane lo P re Polyu thanEEeeppooorrxxyPyolyzsiinc-ricnhe rethan oxaynic siloxaicnhe u ly o rg P re Eop ly cx-ra Polyuanic aonrEeporrxxayyPPnooiclyzsiinlo ich oxy zinc-rich thoarnEeoprg Inolyrgure c-r nic th EEppoooxxayynnic are Pooly ic zinl In a P rgu nic orrEooprg rg h y anic o EpoxxSytee c-ric o anic ezin Inoorg a prg l c-rich E rg in z e In r oorgSatnic l o ic annic or teel Inoorg a SStee In rg
l SStteeeel
y epox y-duty xy Heav uty epo -d y y x v Hea uty eeppooxy y-d Heavy-duty eexly Heav Stepooxly y-duty Steepeel Heeaavvy-duty H Steel
Ste l SStteeeel
m miniu ne alu in m ium m Silico e aalu miniu ium nne lu inluiumm in o o ic il ic SSil e ayluedmainium ium m n ra inluiummin aloosp Sililic ne aaylu m lu edmainiuminium S ic e ra Therm n m m m lu sp o iu iu Silaiclone aayedmaainlu luiummin lu Therm Silaic edmin losp neera emmliniumm iu raaylu e in sp Silaic t m l n S o lu Thheerm a iu lu ic ne d a lin Silic T rm SilalosprayyeeSdtaelueml el al spra Ste Thheerm T rm Stee
l SStteeeel
nolic y phe Epox phheennoolilicc yp EEppooxxy heennoolililiccc y ppheno EEEpppoooxxxyy pphhenolilicc y no Epoxy phe olicc Epooxxyy pphhheeennnnooolililicc l EEppooxxyy pphene oliec EEpppooxxy phhSeetnolilieccl Epoxy phSetneo Epoxy p eel E St l
Stee l Stteeeel S
y epox flake y Glass akkee eeppooxxy a fl y GGlalassss flake eppooxxy e lass fl flakkee epooxxyy Gla G ss fla p Glass flakkeSeetpeoexxyyl e Glass a fl ke epooexly p Glass flakS e tee Glass ss fla Steell Gla tee
S l Stteeeel S
6
Interior surfaces
Generic type Epoxy Epoxy
Dry film thickness 100 µm / 4 mils 100 µm / 4 mils
y Epox y EEppooxxy y Eppooxxy E oxy Ep xy EppooxSyteel E oxy el EpoSxyte Ep el
te l SStee l SStteeeel
7
Exterior production equipment
Generic type Polyurethane or Polysiloxane Epoxy Epoxy Inorganic or organic zinc-rich
Dry film thickness 50 µm / 2 mils or 100 µm / 4 mils 125 µm / 5 mils 125 µm / 5 mils 50 µm / 2 mils
For specific products, see the offshore product range (page 10). Several of Hempel’s coating systems have been tested and pre-qualified for NORSOK M-501.
xane olysilo ane x e or P than orxPyolysilo ane re u Poly thanEepo olysiloxxane lo h P re Polyu thanEEeeppooorrxxyPyolysizinc-ric ic xane n ure Pooly retha Epoorgxayn lysilocx-raicnhe P lyuanicaonrEeporrxxayyPPnooiclyzsiinlo ich o c-rich oprg Inorgurenth ic aonrEEEeppooxxayyynic zzin c-r areth Poooly oxxaynic ein In P lyrgu nic orrEooprg l c-rich oxSyte in anic o Eprg z o Inoorg a icezin prgane l c-rich E In rg ic t o or orgSan l annic eel ic or Ste Inoorg a rg Ste In
l SStteeeel
5
Key offshore products Tough, tougher... HEMPADUR MULTI-STRENGTH GF 35870 – glass flake epoxy Provides excellent corrosion protection as well as high resistance to both impact and abrasion. This product is tailor-made for the severely corrosive atmospheric conditions faced by offshore oil and gas constructions.
Benefits
Reinforcement with high content of lamellar glass flakes (more than 25% by weight of pigments and extenders).
Provides excellent corrosion protection through superior barrier effect.
Immersible just 6 hours after application (20°C/68°F), as curing proceeds under water.
Facilitates repair of structures in tidal zones.
Rain-resistant just 4 hours after application.
Structures can be coated indoors and stored outdoors in wet or humid conditions shortly after application.
High volume solids content (87%).
High-build properties ensure greater dry film thickness in just one or two coats.
Low volatile organic compound content (180 g/litre).
Healthier and safer for applicators, particularly when applied indoors.
NORSOK M-501-approved
Features
A breakthrough in tank linings HEMPADUR 85671 – epoxy phenolic (Novolac) A two-component, amine adduct cured phenolic epoxy (Novolac) coating with excellent resistance to high temperature, water and lining in tanks, pipelines, etc. for hot water, brine, crude oil and potable water.
Benefits
Excellent resistance to hydrocarbons. Also approved for jet fuel.
Excellent/safe choice for cargo tanks and all fuel oil tanks.
Excellent resistance to water at high temperatures – also water contaminated with oil.
Excellent/safe choice for process water and slop tanks.
Very good resistance to high pressure and decompression.
Excellent choice for separators and other pressure vessels.
Approved by WRAS/UK and NSF/USA for contact with potable water.
Excellent/safe choice for drinking water tanks.
New thinking in topcoat solutions HEMPAXANE 55000 – polysiloxane Provides exceptional gloss and colour retention along with excellent resistance to abrasion, spillage of chemicals, stains and
6
Features
Benefits
Excellent colour and gloss retention.
Far superior performance compared to other generic types of topcoats.
High volume solids content (84%).
Complies with VOC regulations all over the world.
Excellent resistance to spillage from a wide range of chemicals.
Greater durability and less risk of damage to steel surfaces.
Excellent barrier effect against diffusion of water and ions.
Longer working life, lower maintenance costs and less risk of premature refurbishment.
Solvent emission to the atmosphere Solvent emission index
NORSOK M-501-approved
UV-light. HEMPAXANE 55000 is not just a topcoat – it is also an integrated part of your corrosion protection.
120 100 80 60 40 20 0
Acrylic
Polyurethane
55000
NORSOK M-501-approved
chemicals. Suitable as an interior
Features
Documentation The specifier, engineer, owner or any other decision-maker
Unfortunately, no accelerated test method used today
responsible for selecting the right coating system to protect
correlates with real-life performance. It is therefore very
offshore installations is very aware of the fact that making
important to understand that even an excellent test result
the wrong choice can be costly.
does not automatically guarantee excellent performance in practice. There are simply too many variables that give rise
Documentation is therefore normally required for major projects
to important differences between laboratory application and
in order to corroborate the performance of the coating system.
testing on the one hand, and real-life situations on the other.
Two types of documentation are often required:
Experience
1) Documentation concerning practical performance, to
Hempel has vast experience in the use of coating systems in
confirm that the coating system has worked satisfactorily
marine and offshore environments. This accumulated know-
under similar conditions.
how makes Hempel an extremely reliable supplier, and the company can deliver extensive documentation on the use of
This documentation is the best possible proof that the system
coating systems in practice.
is efficient under real-life conditions. The main disadvantage of this type of documentation is that many of the coatings
Hempel also carries out comprehensive accelerated tests,
used 10–15 years ago are no longer on the market today.
both internally at its modern Test and Innovation Centre in Denmark, and externally at different recognised independent
2) To
a
certain
extent,
documentation
concerning
laboratories.
performance can also be obtained through accelerated testing. Several standards currently list accelerated test
At the end of the day, optimum corrosion protection is only obtained
methods that should be performed for the qualification
when the coating system is properly applied on-site. In many
testing of coating systems for offshore use.
cases this can only be ensured by a good QAS system, backed up by one of Hempel’s many experienced coating engineers.
Such standards include NORSOK M-501, ISO 12944 and ISO 20340, as well as different NACE standards. Hempel’s internal test package is in fact on a par with or tougher and usually much more comprehensive than the above external test requirements. The above standards specify very extensive requirements and should therefore be suitable for coating systems used in tough offshore conditions.
Hempel’s internal test: • • • • • • •
Surface preparation Application Water immersion Chemical resistance Pull off Impact strength Flexibility
• • • • • • •
Temperature gradient Cathodic disbondment Rust creepage resistance Thermal cycling resistance Colour/gloss retention Edge build Thick film crack resistance
• • • • • •
Abrasion resistance Aging stability Cyclic testing Blister box Salt spray Physical constants
Most of the tests are according to accredited standards such as, ASTM, NORSOK, NACE and ISO.
7
Offshore installations require optimum coating systems Impact and abrasion resistance
Application properties
Recoating intervals
Gloss and colour retention
A balance between crucial performance indicators
Flexibility
Anticorrosive performance Chemical resistance
Gloss and colour retention A good coating system is resistant to the environmental stresses to which it is exposed, and maintains good gloss and colour retention.
Recoating intervals A good coating system provides workable overcoating intervals that ensure better than adequate intercoat
Anticorrosive performance
adhesion.
A good coating system provides good corrosion protection – even in areas that are mechanically damaged.
Application properties A good coating system has good application properties
Chemical resistance A good coating system provides optimum resistance to a
that match the environmental conditions under which it is applied.
wide range of chemicals.
Impact and abrasion resistance Flexibility
A good coating has mechanical properties that match the
A good coating system has sufficient flexibility to withstand
kind of service for which it is intended (flexibility, impact and
steel expansions and contractions at varying temperatures.
abrasion resistance).
8
Problems and solutions Problems encountered with offshore maintenance
Hempel solutions • Reliable supplier with almost a century of worldwide
The cost of coating maintenance is increasing – both when
experience.
carried out on-site and when done during shutdowns or a docking.
• Supplier with a proven quality assurance system that ensures products of a uniform, high quality, anywhere in the world.
Labour, equipment, downtime and even paint are also becoming more and more expensive.
• Supplier that can provide coating systems with documented performance (both in the laboratory and in service).
Many of our customers are well aware of this and they fully understand that maintenance costs can be significantly
• Supplier that not only ensures the supply of products, but
reduced if the right coating system is chosen and applied
also provides expert assistance during the application
correctly – the first time.
– ensuring the best possible result.
But how does a customer choose between good and bad
All these benefits are recognised by most global companies
coating systems? And how can the customer make sure that
working in the oil and gas industry.
the system will provide the best possible lifetime protection? Without a large laboratory consisting of vast test facilities, it is difficult to distinguish between good and bad coating systems – the customer must therefore rely on the supplier’s recommendations. Another concern for many owners during maintenance is how to ensure that even the best coating system in the world is applied properly – and how to do so without a large staff of qualified coating inspectors.
Hempel is a recognised supplier to well-known companies including: • • • • • • •
Shell ENI Group BP ConocoPhillips Statoil ExxonMobil ChevronTexaco
• • • • • • •
Total Saudi Aramco Petronas Maersk Oil & Gas ADNOC Repsol YPF Kuwait Oil Company
9
Hempel’s offshore product range Generic type
Product name
Description
Epoxy
HEMPADUR PRO 45601/3
A universal primer and intermediate for highperformance coating systems for atmospheric or submersed service.
66%
125 µ – 200 µ 5 mils – 8 mils
HEMPADUR UNIQ 47741/3
A unique universal newbuilding primer that provides excellent corrosion protection and abrasion resistance for all areas.
80%
125 µ – 200 µ 5 mils – 8 mils
HEMPADUR MASTIC 45880/1
Multi-purpose coating for maintenance including ballast tanks and new steel.
77%
125 µ – 200 µ 5 mils – 8 mils
HEMPADUR MULTI-STRENGTH 45751/3
A high-strength coating for areas exposed to abrasion and aggressively corrosive climates, such as ramps and drilling decks.
79%
150 µ – 250 µ 6 mils – 10 mils
HEMPADUR SPRAY-GUARD 35490/3
A heavy-duty coating for steel and concrete exposed to severely corrosive conditions and/or impact such as splash zones and decks.
100%
2.5 mm – 3 mm 100 mils – 120 mils
High-strength epoxy
Vol. Solids
Normal DFT Range
Glass flake epoxy
HEMPADUR A self-primed, high-build coating mainly for MULTI-STRENGTH GF 35870 areas subject to abrasion and/or a highly corrosive environment, such as splash zones, jetty pilings and work decks.
87%
350 µ – 500 µ 14 mils – 20 mils
Glass flake polyester
HEMPEL’S POLYESTER GF 35920
A rust-preventive coating for areas exposed to high abrasion and impact.
90%
650 µ – 750 µ 26 mils – 30 mils
Epoxy phenolic
HEMPADUR 85671
An interior lining in tanks, pipelines, etc. for hot water, brine, crude oil and potable water.
68%
100 µ – 125 µ 4 mils – 5 mils
Inorganic zinc silicate
HEMPEL’S GALVOSIL 15700 An inorganic zinc silicate as a single, complete coating for long-term protection of steel exposed to severely corrosive environments.
64%
50 µ – 100 µ 2 mils – 4 mils
HEMPEL’S GALVOSIL 15680 An inorganic zinc silicate as a single, complete coating for long-term protection of steel exposed to severely corrosive environments.
90%
50 µ – 75 µ 2 mils – 3 mils
Zinc-rich epoxy
HEMPADUR ZINC 17360
A versatile, VOC-compliant, long-term primer on steel for epoxy, polyurethane and polysiloxane coating systems in severely corrosive environments.
65%
50 µ – 75 µ 2 mils – 3 mils
Polyurethane topcoats
HEMPATHANE TOPCOAT 55210
A two-component, acrylic polyurethane coating with excellent gloss and colour retention. Good resistance to water, impact and abrasion.
52%
40 µ – 60 µ 1.6 mils – 2.4 mils
HEMPATHANE TOPCOAT 55910
A VOC-compliant, high-build finishing coat for protection of structural steel in corrosive environments, especially for maintenance.
66%
75 µ – 125 µ 3 mils – 5 mils
HEMPEL’S URETHANE 5595U
A deluxe finishing coat for protection of structural steel in severely corrosive environments.
63%
40 µ – 60 µ 1.6 mils – 2.4 mils
Polysiloxane topcoat
HEMPAXANE 55000
An isocyanate-free glossy protective finishing coat for new steel structures in severely corrosive environments.
84%
100 µ – 125 µ 4 mils – 5 mils
Modified acrylic – isocyanate-free topcoat
HEMPEL’S PRO ACRYLIC 55880
An isocyanate-free finishing coat in severe atmospheric environments where safety rules preclude the use of isocyanate-cured paints.
56%
50 µ – 100 µ 2 mils – 4 mils
Heat-resistant
HEMPEL’S SILICONE ALUMINIUM 56910
For long-term protection of hot pipelines, exhaust pipes, smoke stacks and other hot surfaces.
35%
25 µ 1 mil
Self-polishing antifouling
HEMPEL’S ANTIFOULING GLOBIC RANGE
Self-polishing antifouling.
58%
50 µ – 100 µ 2 mils – 4 mils
10
Availability
Hempel worldwide Most major construction projects today involve companies from many nations, with different sections being constructed in different countries before final assembly on site. Delays in the construction of any of these sections mean costly delays for the entire project. This is why the rapid, efficient supply of paint is an important key to our customers’ success. Hempel’s worldwide presence is perfectly suited to the multinational construction business, regardless of whether this involves petrochemical plants, tank farms, bridges, power plants or offshore platforms. The Hempel Group of companies currently comprises 22 manufacturing plants, 5 R&D centres, 46 sales and service offices and more than 120 stock points around the world. We operate with a worldwide product assortment, which means our products are readily available wherever and whenever required. For operators within the maritime industry, Hempel paints are readily available at all major ports of call. Contact your local Hempel office for further information and answers to any questions.
Comprehensive information about Hempel products and services is always available at www.hempel.com
11 / 2004
The Hempel Group Head Office Hempel A/S Lundtoftevej 150 DK-2800 Kgs. Lyngby Denmark Phone: +45 45 93 38 00 Main fax: +45 45 88 55 18 E-mail: [email protected]
Hempel offices in main offshore markets Buenos Aires Office Hempel (Argentina) S.R.L. Libertad 1213, 2nd floor (C1012AAY) Capital Federal, Buenos Aires Argentina Phone: +54 11 4816 3137 +54 11 4812 7450 Fax: E-mail: [email protected] Dammam Office Hempel Paints (Saudi Arabia) W.L.L. P. O. Box 1077, Dammam 31431 Saudi Arabia Phone: +966 3 847 1616 Fax: +966 3 847 1816 E-mail: [email protected]
Bergen Office Hempel (Norway) A/S Liavegen 12, P. O. Box 163, Nyborg N-5871 Bergen Norway Phone: +47 55 95 80 00 Fax: +47 55 95 80 50 E-mail: [email protected]
Houston Office Hempel (USA) Inc. 600 Conroe Park Nor th Drive Conroe, Texas 77303 USA Phone: +1 936 523 6000 +1 936 523 6073 Fax: E-mail: [email protected]
Hong Kong and China Office Hempel-Hai Hong (China) Ltd. Room 1408, South Tower China Merchants Plaza 333 Chengdu Road Nor th Shanghai 200041 The People’s Republic of China Phone: +86 21 5298 1258 Fax: +86 21 5298 1088
Singapore Office Hempel (Singapore) Pte. Ltd. 25, Tuas Avenue 11, Singapore 639088 Singapore Phone: +65 6 799 8383 Fax: +65 6 799 8400 [email protected] E-mail:
Doha Office Hempel Paints (Qatar) W.L.L. P. O. Box 3484 Doha Qatar Phone: +974 460 0881 +974 460 0901 Fax: E-mail: [email protected]
For other Hempel offices visit our website www.hempel.com 12
12