Balticare - Product and Application Handbook EU-Vol II [PDF]

Zitiervorschau

®

Product and Application Handbook EU - VOLUME II

Welcome... ... to the European edition of the BAC Product and Application Handbook. In an era of information transfer, we are excited to make available to you a unique compilation of industry knowledge and product application details. This handbook reflects our commitment to facilitate the application of our products, services and technical resources for higher system efficiency, environmental responsibility and safe operation. BAC has a rich history in the design and development of the world's largest range of evaporative cooling and ice thermal storage products. A specialised hygiene services initiative is also presented in support of these products. I hope you will find this publication to be a valuable resource and a service to the industry… because temperature matters. Sincerely,

Andreas G. Coumnas Managing Director - Europe

A1

Contents Table of Contents Technical Resources . . . . . . . . . . . . . . . . . . . .G

Introduction to Heat Transfer Products . . . . . . . . . . . . . . . .A4

Connection Guide . . . . . . . . . . . . . . . . . . . . . . . . . .TR - G

Open Cooling Towers . . . . . . . . . . . . . . . . . . . . . . . .B

Materials of Construction . . . . . . . . . . . . . . . . . . . . .TR - G

Overview & Engineering Considerations . . . . . . . . . .CT - B

Selection Software . . . . . . . . . . . . . . . . . . . . . . . . . . .TR - G

Series 3000-D Open Cooling Towers . . . . . . . .S3000-D - B

The Value of Standards . . . . . . . . . . . . . . . . . . . . . . .TR - G

TXV Open Cooling Towers . . . . . . . . . . . . . . . . . . .TXV - B

Selection of Remote Sump Tank . . . . . . . . . . . . . . . .TR - G

FXT Open Cooling Towers . . . . . . . . . . . . . . . . . . . .FXT - B

Filtration Options . . . . . . . . . . . . . . . . . . . . . . . . . . . .TR - G

RCT Open Cooling Towers . . . . . . . . . . . . . . . . . . .RCT - B

Sound Reduction Options . . . . . . . . . . . . . . . . . . . . .TR - G

IMT Open Cooling Towers . . . . . . . . . . . . . . . . . . . .IMT - B

Fundamentals of Sound . . . . . . . . . . . . . . . . . . . . . .TR - G

VTL Open Cooling Towers

. . . . . . . . . . . . . . . . . . .VTL - B

Controls . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .TR - G

VXT Open Cooling Towers

. . . . . . . . . . . . . . . . . . .VXT -B

Plume Abatement . . . . . . . . . . . . . . . . . . . . . . . . . . .TR - G

Closed Circuit Cooling Towers . . . . . . . . . . . . . . . . .C

Formulas and Tables . . . . . . . . . . . . . . . . . . . . . . . . .TR - G

Overview & Engineering Considerations . . . . . . .CCCT - C

Replacement Parts . . . . . . . . . . . . . . . . . . . . . . . . . .TR - G

FXV Closed Circuit Cooling Towers . . . . . . . . . . . .FXV - C

Application Guidelines . . . . . . . . . . . . . . . . . . . . . . . .TR - G

VXI Closed Circuit Cooling Towers . . . . . . . . . . . . .VXI - C

Glossary . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .TR - G

VFL Closed Circuit Cooling Towers

. . . . . . . . . . . .VFL - C

Water Conserving Hybrid Wet-Dry Products . . . . . . .D

Handbook Resources

Overview & Engineering Considerations . . . . . . . .HWD - D

Color Coded Sections

HXI Hybrid Closed Circuit Cooling Tower . . . . . . . . .HXI - D

Vertical Identification Bars

HFL Hybrid Closed Circuit Cooling Tower

Sectional Icons

. . . . . . .HFL - D

DFC Dry Cooler . . . . . . . . . . . . . . . . . . . . . . . . . . . .DFC - D

Open Cooling Towers

DFC-AD TrilliumSeries Cooler . . . . . . . . . . . .DFCV-AD - D

Closed Circuit Cooling Towers

DCV-AD TrilliumSeries Condenser . . . . . . . . . .DCV-AD - D

Water Conserving Hybrid Wet-Dry Products

HXC Hybrid Condenser . . . . . . . . . . . . . . . . . . . . .HXC - D Evaporative Condensers . . . . . . . . . . . . . . . . . . . . . .E Overview & Engineering Considerations . . . . . . . . . .EC - E VXC Evaporative Condensers . . . . . . . . . . . . . . . . .VXC - E VCL Evaporative Condensers . . . . . . . . . . . . . . . . .VCL - E CXV Evaporative Condensers . . . . . . . . . . . . . . . . .CXV - E TSU ICE CHILLER® . . . . . . . . . . . . . . . . . . . . . . . . . . F Thermal Storage Products . . . . . . . . . . . . . . . . . . . .TSU - F

Evaporative Condensers ICE CHILLER® Thermal Storage Products

Complete Product Brochures featuring Product Introductions Benefits Construction Details Custom Features & Options Accessories Engineering Data Structural Support Engineering Specifications

Technical Resources

Table of Contents

Baltimore Aircoil Company . . . . . . . . . . . . . . . . . . . . . . . . . . .A1

A2

Commitment For more than seven decades Baltimore Aircoil Company has been dedicated to the development of innovative, cost effective heat transfer solutions for its customers. This has established BAC as the global leader of factory assembled evaporative heat rejection and thermal storage equipment.

Design Ongoing investment in research and development, combined with sophisticated R&D laboratory facilities enables BAC to consistently offer technology and products in advance of new industry demands.

Selection BAC offers the widest array of factory assembled evaporative heat rejection and thermal storage equipment in the industry. Breadth of product enables BAC to provide its customers optimized solutions with regard to their specific needs. Whether an application calls for open or closed cooling circuits, axial or centrifugal fans, special materials of construction or unique dimensional considerations, BAC has the solution.

Performance All BAC products are engineered to minimize lifecycle costs through a combination of low energy consumption and low maintenance. An extensive array of options addresses such issues as low sound or low water consumption requirements.

A3

How can we help? From employees to partners every action at BAC centers on you, the customer. Our service philosophy extends beyond customer service to embody a total service approach. So from application to installation to aftermarket needs, whether you are working with our representatives, the Product & Application Handbook or using www.BaltimoreAircoil.com, BAC has a tool to help.

BAC Sales Channel BAC employs the most extensive and experienced network of manufacturer’s representatives to provide you unrivalled local support for your specific application needs. Integrated globally, the BAC network of representatives facilitates design support for projects coordinated on a local, national, or international scale.

BAC Product & Application Handbook A revolutionary tool for assisting with equipment application and selection requirements, it is the only place to find critical industry technical and product information together in one convenient format.

www. BaltimoreAircoil.com A proprietary online tool that allows access to resources and education to assist product evaluation, comparison and selection.

• Product Information • Selections • Equipment Specifications • Technical Information • Rigging and Installation Manuals

A4

Heat Transfer Products Evaporative cooling products minimize the energy consumption of the entire system by providing lower operating temperatures than possible with comparably sized air-cooled equipment. BAC has a large selection of heat transfer products to offer, each of which falls into one of these five main categories:

Open Cooling Towers Open cooling towers are a proven and cost-effective method of cooling condenser water loops and industrial processes. In operation, the condenser water (or process water) flows directly over the heat transfer surface of the open cooling tower. As air is introduced into the tower, a fraction of this water is evaporated, cooling the remaining water.

Closed Circuit Cooling Towers Closed circuit cooling towers keep the process fluid clean and contaminant free in a closed loop. This creates two separate fluid circuits: (1) an external circuit, in which spray water circulates over the coil and mixes with the outside air, and (2) an internal circuit, in which the process fluid to be cooled circulates inside the coil. During operation, heat is transferred from the warm fluid in the coil to the spray water, and then to the atmosphere as a portion of the water evaporates. In addition to chiller applications and industrial process cooling, closed circuit cooling towers are often used in heat pump loops, where closed loop cooling is preferred.

Water Conserving Hybrid Wet-Dry Products Water conserving and hybrid products are usually of the closed circuit type. The hybrid wet-dry products cool the liquid to be cooled by efficiently combining dry sensible air cooling with evaporative dooling. These products include two or more distinctive heat transfer surfaces or sections combined into one product optimising the use of ambient dry and wet bulb temperature. Low water and water treatment cost, vastly improved opearational safety and virtual elimination of visible plume are the main advantages of “intelligent” water saving products.

Evaporative Condensers When applied to HVAC and light industrial systems, evaporative condensers provide lower condensing temperatures and compressor kW savings of up to 15 percent compared with traditional systems. In an evaporative condenser, refrigerant vapor is condensed in a coil, which is continually wetted on the outside by a recirculating water system. Air is circulated over the coil, causing a small portion of the recirculating water to evaporate. The evaporation removes heat from the vapor in the coil, causing it to condense.

Ice Thermal Storage Products Ice thermal storage units are used to build and store cooling in the form of ice during periods of reduced cooling demand. This way the mechanical refrigeration system need not be sized on peak load but on "average" conditions. Hence a smaller refrigeration system with lower power requirements and a smaller refrigerant charge can be selected. Compared to conventional refrigeration systems, ice thermal storage systems generally have a higher compressor operating efficiency since the compressor will operate continuously at full capacity and not at fluctuating part load conditions. Ice thermal storage units can either be of the "internal" or ""external" melt type. For "internal melt" only glycol solutions can be used as secondary refrigerant. "External melt" ice thermal storage units can use either direct refrigerant feed or glycol solutions.

Need help deciding which product to use? Contact your local BAC Balticare Representative for assistance.

Baltimore Aircoil

CT - B 1

Open Cooling Towers Overview

Open Cooling Towers

Product Group Detail General Information ................................................................................. B2 Principle of Operation .............................................................................. B2 Configuration ............................................................................................. B2 Water Distribution System ....................................................................... B2 Fan System ................................................................................................. B3 Capacity Range .......................................................................................... B3 Maximum Entering Water Temperature ................................................ B4 Typical Applications .................................................................................. B4 Product Line Overview Table .................................................................. B4 Engineering Considerations ..................................................................... B6

CT - B 2

General Information Open cooling towers provide evaporative cooling for many types of systems, and the specific application will largely determine which BAC Cooling Tower is best suited for a project. The Product Line Overview Table is intended as a general guide. Specialised assistance is available through your local BAC Balticare Representative.

Overview

Principle of Operation Open cooling towers reject heat from water-cooled systems to the atmosphere. Hot water from the system enters the cooling tower and is distributed over the wet deck (heat transfer surface). Air is pulled or pushed through the wet deck, causing a small portion of the water to evaporate. Evaporation removes heat from the remaining water, which is collected in the cold water basin and returned to the system to absorb more heat. Each open cooling tower line, although operating under the same basic principle of operation, is arranged a little differently. See the schematics on the Product Line Overview Table for product specific details.

Configuration There are two main configurations of factory assembled open cooling towers: crossflow and counterflow. In crossflow cooling towers, the water flows vertically down the wet deck as the air flows horizontally across it. In counterflow cooling towers, the water flows vertically down the wet deck as the air flows vertically up it.

Crossflow Configuration

Counterflow Configuration

Water Distribution System Open cooling towers employ either gravity distribution or pressurised spray systems to distribute water over the wet deck surface. Gravity distribution systems, installed on BAC’s crossflow cooling towers, feature hot water basins mounted on top of the tower above the wet deck. A series of metering orifices in the floor of each hot water basin distribute the water as a function of the depth of the water in the basin. Gravity distribution systems generally require minimal pump head, can be inspected while the unit is in operation and are easy to access for routine maintenance and service. Spray distribution systems, employed on counterflow cooling towers, feature a series of pipes fitted with spray nozzles mounted inside the tower above the wet deck. These systems typically require 0,15 through 0,5 bar of water pressure at the water inlet and require the unit to be out of service for inspection and maintenance.

Baltimore Aircoil

CT - B 3

Pressurised Spray Distribution

Fan System The flow of air through most factory assembled evaporative cooling equipment is provided by one or more mechanically driven fans. The fan(s) may be axial or centrifugal, each type having its own distinct advantages. Axial fan units require approximately half the fan motor kilowatt of comparably sized centrifugal fan units, offering significant life-cycle cost savings. Centrifugal fan units are capable of overcoming reasonable amounts of external static pressure (≤125 Pa), making them suitable for both indoor and outdoor installations. Centrifugal fans are also inherently quieter than axial fans, although the difference is minimal and can often be overcome through the application of optional low sound fans and/or sound attenuation on axial fan units. Fans can be applied in an induced draft or a forced draft configuration.

Centrifugal Fans

Axial Fans

Induced Draft The rotating air handling components of induced draft equipment are mounted in the top deck of the unit, minimizing the impact of fan noise on near-by neighbors and providing maximum protection from fan icing with units operating in sub-freezing conditions. The air being drawn through the unit hereby discharges over the inducing fan. The use of corrosion resistant materials ensures long life and minimizes maintenance requirements for the air handling components. Forced Draft Rotating air-handling components are located on the air inlet face at the base of forced draft equipment whereby fresh air is blown through the unit. This base fan position facilitates easy access for routine maintenance and service. Additionally, location of these components in the dry entering air stream extends component life by isolating them from the corrosive saturated discharge air.

Capacity Range In the following Product Line Overview Table, product capacity range is called out in terms of water flow capability at 35ºC/30ºC/21ºC. A nominal cooling tower capacity is defined at 35ºC entering water temperature to a 30ºC leaving water temperature at a 21ºC entering wet-bulb temperature. Nominal conditions are typical of conventional HVAC designs but will not apply to all projects. All water flow capacities shown are for a single cell; multiple cell units can be applied to achieve larger capacities.

... because temperature matters

Open Cooling Towers

Gravity Distribution Basin

CT - B 4

Maximum Entering Water Temperature As previously stated, typical HVAC conditions call for an entering water temperature of approximately 35ºC. All BAC Cooling Towers are capable of withstanding temperatures of at least 50ºC with standard fill materials. For applications where the entering water temperature exceeds 50ºC, check the Product Line Overview Table or consult your local BAC/Balticare representative to determine whether alternate fill materials are available for your project.

Overview

Typical Applications A list of typical applications is provided in the Product Line Overview Table for your reference.

Product Line Overview Table Series 3000-D

TXV

FXT

2

3 8

2

3

3

8

3

Principle of Operation

9

8

6

2

5

6

5

5

5 9

1

1

1

9

6

1

7

7

7

4

4

4

Configuration

Crossflow

Crossflow

Crossflow

Water Distribution

Gravity

Gravity

Gravity

Fan System

Axial Fan, Induced Draft

Axial Fan, Induced Draft

Axial Fan, Forced Draft

Capacity Range (Single Cell)

40 to 260 l/s

10 tot 128 l/s

3 tot 145 l/s

Maximum Entering Water Temperature

50 °C standard wet deck 55°C Alternative wet deck material

50 °C standard wet deck 55°C Alternative wet deck material

50 °C standard wet deck 55°C Alternative wet deck material

Typical Applications

Medium to large HVAC & industrial applications Replacement of field erected towers

Medium HVAC & industrial applications Counterflow unit replacements Crossflow unit replacements Tight enclosures & installations requiring a single air inlet

Small to medium industrial applications

1. Air in, 2. Air Out, 3. Hot Water In, 4. Cooled Water out, 5. Water; 6. Wet Deck Surface, 7. Cold Water Basin; 8. Water Distribution System; 9. Eliminators.

Note: For projects requiring water conservation and/or plume sensitive location, VXT and VTL cooling towers can be equipped with plume abatement coils (PAC) in combination with 2-way valve arrangement. Refer to your BAC Balticare representative for more details and selections.

Baltimore Aircoil

CT - B 5

Note : BAC offers heat exchanger skids in combination with most of his open cooling tower products. These skids are available for both new installations or to retrofit on existing installations. The heat exchanger skid consists of a plate heat exchanger with pump and interconnecting piping and appendages. The skids are delivered on a heavy duty frame and with steel panel enclosure. Refer to your BAC Balticare representative for more details and selections.

IMT

VTL

VXT

2

2

2

9

6

8

3

6

3

6

8 5

1

1

7

4

6

3 1

1

7

3

5

5

5 1

2

9

8

8

4

1

7

4

7

4

Counterflow

Counterflow

Counterflow

Counterflow

Pressurised

Pressurised

Pressurised

Pressurised

Axial Fan, Induced Draft

Axial Fan, Induced Draft

Centrifugal Fan, Forced Draft

Centrifugal Fan, Forced Draft

40 to 145 l/s

35 to 575 l/s

4 tot 90 l/s

1,6 to 1230 l/s

55°C Standard Wet Deck 60°C w/Alternate Wet Deck Materials

55°C Standard Wet Deck 65°C w/Alternate Wet Deck Materials

55°C Standard Wet Deck 65° C w/Alternate Wet Deck Materials

55°C Standard Wet Deck 65°C w/Alternate Wet Deck Materials

Large industrial applications Replacement of field erected towers with basinless units Dirty water applications.

Small to medium HVAC & Industrial applications Installations w/extremely low height requirements Indoor Installations High temperature industrial applications Tight enclosures & installations requiring a single air inlet

Small to medium HVAC & industrial applications Indoor installations High temperature industrial applications Tight enclosures & installations requiring a single air inlet

Small to medium industrial applications Dirty Water applications

... because temperature matters

Open Cooling Towers

RCT

CT - B 6

Engineering Considerations Location Units must have an adequate supply of fresh air to the air inlet(s). When units are located adjacent to building walls or in enclosures, care must be taken to ensure that the warm, saturated discharge air is not deflected off surrounding walls or enclosures and drawn back to the air inlet(s).

Overview

Warning: Each unit should be located and positioned to prevent the introduction of the warm discharge air and the associated drift, which may contain chemical or biological contaminants including Legionella, into the ventilation systems of the building on which the unit is located or those of adjacent buildings.

Note: For detailed recommendations on layout, please consult your local BAC Balticare Representative.

For VL and VX products, bottom screens or solid bottom panels may be desirable or necessary for safety, depending on the location and conditions at the installation site.

Piping and Valves Piping must be sized and installed in accordance with good piping practice. All piping should be supported by pipe hangers or other supports, not by the unit. On open systems, in order to prevent basin overflow at shutdown and to ensure satisfactory pump operation at start-up, all heat exchangers and as much piping as possible should be installed below the operating level of the cooling tower. Some units may require flow balancing valves (supplied by others) at the hot water inlets to balance the flow to individual inlets and cells. External shutoff valves (supplied by others) may also be required if the system design necessitates the isolation of individual cells. When multiple cells are used on a common system, equalizing lines should be installed between the cold water basins to ensure balanced water level in all cells. It is good engineering practice to valve the inlet and outlet of each tower separately for servicing. The shut-off valves can be used, if necessary, to adjust any minor unbalanced condition in water flow to or from the units.

Capacity Control Variable Frequency Drives (VFD) Installations which are to be controlled by Variable Frequency Drives (VFD) require the use of an inverter duty motor as designed IEC 34.1, which recognizes the increased stresses placed on motors by these drive systems. Inverter duty motors must be furnished on VFD applications in order to maintain the motor warranty. Fan motors must be furnished with thermal protection (either PTC sensors or coil thermostats normally open, or normally closed). The motor protection consists of temperature sensitive cutout devices embedded in the motor windings (minimum 3 per motor). The minimum fan motor speed during normal operation should not be below 30% of the speed indicated on the motor nameplate. This corresponds with 15 Hz for a 50 Hz supply and 18 Hz for a 60 Hz supply. BAC offers factory installed motor control packages including VFD drives. Refer to the section "Technical Resources, Motor Controls". Check with your local BAC Balticare representative for availability. Warning: When the fan speed is to be changed from the factory-set speed, including through the use of a variable speed control device, steps must be taken to avoid operating at or near fan speeds that cause a resonance with the unit or its supporting structure. At start-up, the variable frequency drive should be cycled slowly between zero and full speed and any speeds that cause a noticeable resonance in the unit should be “locked out” by the variable speed drive.

Fan Cycling Fan cycling is the simplest method of capacity control. The number of steps of capacity control can be increased using the Baltiguard® Fan System, the independent fan motor option, or two-speed fan motors in conjunction with fan cycling (see the “Custom Features & Options” section of the

Baltimore Aircoil

CT - B 7

appropriate product line to determine whether the Baltiguard® Fan System or the independent fan motor option are available; two-speed motors are available for all products). These options provide substantial energy savings when compared to simple fan cycling. Warning: Rapid on-off cycling can cause the fan motor to overheat. It is recommended that controls be set to allow a maximum of 6 on-off cycles per hour.

Vibration Cut-out Switch Vibration cut-out switches are recommended on all axial fan installations. Vibration cut-out switches are designed to interrupt power to the fan motor and/or provide an alarm to the operator in the event of excessive vibration. BAC offers both electronic and mechanical vibration cut-out switches on all cooling towers.

Water Treatment As water evaporates in the unit, the dissolved solids originally present in the water remain in the system. The concentration of these dissolved solids increases rapidly and can cause scale and corrosion. In addition, airborne impurities and biological contaminants, including Legionella, may be introduced into the circulating water. To control all potential contaminants, a water treatment program must be employed. In many cases, a simple bleed-off may be adequate for control of scale and corrosion. However, biological contamination, including Legionella, can be controlled only through the use of biocides. Such treatment should be initiated at system startup, after periods of equipment shutdown, and continued regularly thereafter. Accordingly, it is strongly recommended a biocide treatment be initiated when the unit is first filled with water and continued regularly thereafter. For more information, consult the appropriate Operating and Maintenance Manual. When a water treatment program is employed, it must be compatible with construction materials. Batch feeding of chemicals into the unit is not recommended. If units are constructed with optional corrosion resistant materials, acid treatment may be considered; however, the water quality must be maintained within the guidelines set forth in the Operating and Maintenance Instructions. Note: Unless a common remote sump is utilised, each cell of a multi-cell installation must be treated as a separate entity, even if the cold water basins are equalized.

For complete Water Quality Guidelines, see the appropriate Operating and Maintenance Instruction Manual, available at www.baltimoreaircoil.com. For specific recommendations on water treatment, contact a competent water treatment supplier.

Sound Levels Sound rating data are available for all BAC models. When calculating the sound levels generated by a unit, the designer must take into account the effects of the geometry of the tower as well as the distance and direction from the unit to noise-sensitive areas. Whisper Quiet fans and intake and discharge sound attenuation can be supplied on certain models to provide reduced sound characteristics (see the “Custom Features and Options” section of the appropriate product line for details). The Baltiguard® Fan System, two-speed motors, or variable frequency drives can also be used to reduce sound during periods of non-peak thermal loads. For more information on sound and how it relates to evaporative cooling equipment, see Section "Technical Resources, Fundamentals of Sound". For detailed low sound selections, please consult your local BAC Balticare Representative.

... because temperature matters

Open Cooling Towers

Capacity Control Dampers (VTL and VXT Models Only) On centrifugal fan models, modulating capacity control dampers are available to provide close control of the leaving temperature. See Section "Accessories" or contact your local BAC Balticare representative.

CT - B 8

Overview

Winterization When a unit is shut down in freezing weather, the basin water must be protected by draining to an indoor auxiliary remote sump tank or by providing supplementary heat to the cold water basin. Supplementary heat can be provided by electric immersion heaters or in some cases, hot water, steam coils, or steam injectors. All exposed water piping, make-up lines, and spray pumps (if applicable) that do not drain at shutdown should be traced with electric heater tape and insulated. For remote sump applications, the spray water pump must be selected for the required flow at a total head which includes the vertical lift, pipe friction (in supply and suction lines) plus the required pressure at the inlet header of the water distribution system (14 kPa). A valve should always be installed in the discharge line from the pump to permit adjusting flow to the unit requirement. Inlet water pressure should be measured by a pressure gauge installed in the water supply riser at the spray water inlet, and adjusted to the specified inlet pressure.

Indoor Installations (applicable to VTL and VXT models only) Many indoor installations require the use of inlet and/or discharge ductwork. Units installed with inlet ductwork must be ordered with solid-bottom panels. Generally, intake ducts are used only on smaller units while the equipment room is used as a plenum for larger units. Discharge ductwork will normally be required to carry the saturated discharge air from the building. Both intake and discharge ductwork must have access doors to allow servicing of the fan assembly, drift eliminators, and water distribution system. All ductwork is supplied and installed by others and should be symmetrical and designed to provide even air distribution across the face of air intakes and discharge openings. Such ductwork may increase the external static pressure on the unit, requiring a larger fan motor to be installed. This external static pressure must be quantified (in Pa) to BAC to allow for suitable fan motor sizing. Warning: The discharge opening must be positioned to prevent the introduction of discharge air into the fresh air intakes serving the unit or the ventilation systems of adjacent buildings.

Note: Axial fan units are not suitable for indoor installations.

Safety Adequate precautions, appropriate for the installation and location of these products, should be taken to safeguard the public from possible injury and the equipment and the premises from damage. Operation, maintenance and repair of this equipment should be undertaken only by personnel qualified to do so. Proper care, procedures and tools must be used in handling, lifting, installing, operating, maintaining, and repairing this equipment to prevent personal injury and/or property damage.

Wet Deck Surface Compatibility BAC’s standard wet deck is constructed of plastic material. The wet deck surface is compatible with the water found in most evaporative cooling applications. The maximum allowable water temperature for each product is as shown in the following table Product Line

Standard Wet Deck

High Temperature Wet Deck

FRP

VTL

55°C

65°C

N/A

VXT

55°C

65°C

N/A

S3000D

50°C

55°C

N/A

TXV

50°C

55°C

N/A

FXT

50°C

55°C

N/A

IMT

55°C

65°C

55°C

RCT

55°C

60°C

55°C

N/A = not applicable

For applications where the entering water temperature exceeds the limits shown above, contact your local BAC Balticare Representative for assistance.

Baltimore Aircoil

S3000D - B 1

S3000D

Open Cooling Towers

Open Cooling Towers

Product Detail S3000D Open Cooling Towers .................................................................. B2 Benefits ....................................................................................................... B4 Construction Details .................................................................................. B6 Custom Features and Options .................................................................. B7 Accessories ................................................................................................. B9 Engineering Data ..................................................................................... B12 Structural Support .................................................................................. B17 Engineering Specifications ..................................................................... B21

S3000D - B 2

S3000D Open Cooling Towers Capacity Single Cell Capacity:

S3000D

40 – 260 l/s

General Description Series 3000D Cooling Towers deliver fully rated thermal performance over a wide range of flow and temperature requirements. Standard design features satisfy today’s environmental concerns, minimize installation costs, maximize year-round operating reliability, and simplify maintenance requirements.

Key Features z

Low energy consumption

z

Low installed cost

z

Easy maintenance

z

Reliable year-round operation

z

Long service life

z

Easy removable high efficient fill as standard

z

Cold water basin is to be free draining

Baltimore Aircoil

S3000D - B 3

Open Cooling Towers

... because temperature matters

S3000D - B 4

Benefits Low Energy Consumption

S3000D

z

z

Evaporative cooling equipment minimises the energy consumption of the entire system because it provides lower operating temperatures. The owner saves money while conserving natural resources and reducing environmental impact. The cooling towers provide the heat rejection required at the lowest possible energy input via: - High efficiency, low kW axial fans - High efficiency easy removable heat exchange surface, which provides maximum air/water contact time at low air pressure drops - Variable Frequency Drives

Low Installed Cost z

z

Support – All models mount directly on two parallel I-beams and ship complete with motors and drives factory-installed and aligned. Modular Design – Models S3-D728L through S3-D1056L and S3-D1132L through S3-D1301L ship in two sections to minimise the size and weight of the heaviest lift, allowing for the use of smaller, less costly cranes.

Modular Design

Combined Inlet Shields

Reliable Year-Round Operation z

z

Belt Drive System utilizes special corrosion-resistant materials of construction and state-ofthe-art technology to ensure ease of maintenance and reliable year-round performance. Combined Inlet Shields prevent biological growth from sunlight, act as a filter for air borne impurities and debris and eliminate water splash out.

Baltimore Aircoil

S3000D - B 5

Easy Removable Fill The fill removal system allows nesting the fill in place for cleaning or replacement. The fill section can easily be reached through the access hatch in the hot water basin. Telescopic fill supports allow for complete fill removal.

Sloped Cold Water Basin

Free Draining Cold Water Basin The sloping cooling tower basin allows for free draining.

Long Service Life z

z

Frame Construction – Enables casing panels, critical links for long service life, to be constructed of corrosion-resistant, fiberglass reinforced polyester (FRP). Materials of Construction – Various materials are available to meet the corrosion resistance, unit operating life, and budgetary requirements of any project (see section: Custom Features and Options for more details).

S3000D Frame Construction shown without FRP Panels

Easy Maintenance z

z

Easy Cleaning – The wet deck surface is elevated above the sloped cold water basin floor to facilitate flushing of dirt and debris from this critical area. Hinged Access Doors – Provide easy entry to the spacious plenum for routine drive maintenance.

Elevated Wet Deck Surface

Easy Access to Hot Water Basin

... because temperature matters

Open Cooling Towers

Removable Fill on Telescopic Fill Supports

S3000D - B 6

S3000D

Construction Details

1. Heavy-Duty Construction Heavy-gauge Z600 galvanized steel frame

2. FRP Casing Panels z Corrosion resistant

z Large orifice, non-clog nozzles z Steel distribution covers

6. BACross II Wet Deck Surface with Integral Drift Eliminators (Not Shown) z Plastic material

z UV resistant finish

z Impervious to rot, decay and biological attack

z Maintenance free

z Designed and manufactured by BAC

3. Fan Drive System

7. Combined Inlet Shields

z Premium quality belts z Corrosion resistant sheaves

z Corrosion Resistant z Easily removable

z Heavy-duty bearings z Adapted fan motor for operation in saturated conditions.

4. Low kW Axial Fan

z UV resistant plastic material

8. Cold Water Basin z Sloped cold water basin for easy cleaning

z Quiet operation

z Suction strainer with anti-vortex hood

z High Efficiency z Corrosion resistant aluminum

5. Water Distribution System z Low pump head gravity distribution basin

z Adjustable water make-up assembly from inside the unit

9. Hinged Access Doors (Not Shown) z Inward swinging door on each end wall

Baltimore Aircoil

S3000D - B 7

Custom Features and Options Construction Options z

z

Optional BALTIBOND® Corrosion Protection System: The BALTIBOND® Corrosion Protection System, a hybrid polymer coating used to extend equipment life, is applied to all hot-dip galvanized steel components of the unit. Optional Stainless Steel Cold Water Basin: A type 304 or 316 stainless steel cold water basin is provided.

Note: See section Technical Resources, Material Options for more details on the materials described above.

Fan Drive System The low sound fan drive system provides the cooling air necessary to reject heat from the system to the atmosphere. The standard fan drive system consists of two sheaves located on minimum shaft centreline distances to maximise belt life. A fan motor, custom engineered for BAC to provide maximum performance for cooling tower service, is provided.

Fan Drive System

Low Sound Operation The ultra low sound levels generated by Series 3000D Cooling Towers make them suitable for installation in most environments. For very sound sensitive installations, the Series 3000D is available with a “Whisper Quiet Fan” - option that significantly reduces the sound levels generated from the tower. For extremely sound sensitive installations, factory designed, tested and rated sound attenuation is available for both the air inlet and discharge of Series 3000D Cooling Towers.

S3000D with Intake and Discharge Attenuator

No discharge attenuator for units with Whisper Quiet Fan. Note: For more information, please refer to the section “Technical Resources, Sound Reduction Options”.

... because temperature matters

Open Cooling Towers

z

Standard Construction: Steel panels and structural elements are constructed of Z600 heavy-gauge hot-dip galvanized steel. All external steel panels are protected with the Baltiplus Corrosion Protection. Casing panels are constructed of UV resistant fiberglass reinforced polyester.

S3000D - B 8

Gear Drive System, Externally Mounted Motor A gear drive system with a TEFC motor mounted outside the airstream is also available on Series 3000D Cooling Towers. A non-corrosive carbon-fiber composite drive shaft with stainless steel hubs is selected with a 2.0 service factor. The motor and drive shaft ship separately for easy field installation.

S3000D

Gear Drive System, Closed-Coupled Motor A close-coupled gear drive system is available as a fan drive option on Series 3000D Cooling Towers. Both the gear drive and couplings are selected with a 2,0 service factor. Gear construction includes a nickel-alloy steel shaft, casehardened gears, self-lubrication, and a single piece, gray iron housing. This drive system ships completely installed and aligned.

Remote Sump Execution The use of an auxiliary sump within a heated Gear Drive System space is the most satisfactory way to protect sump water from freezing. When the circulating pump is shut off, all the water in the water distribution, in suspension and in the sump will drain freely to the auxiliary sump. Note: For detailed information on the calculation of the remote sump tank, please refer to the section "Technical Resources, Selection of Remote Sump Tank".

Combined Inlet Shields Combined Inlet shields prevent biological growth from sunlight, act as a filter for air borne impurities and debris and eliminate water splash out.

High Temperature Wet Deck If operation above 50°C is anticipated, an optional high temperature wet deck material is available which increases the maximum allowable entering water temperature to 55°C.

Combined Inlet Shields

Baltimore Aircoil

S3000D - B 9

Accessories Ladder, Safety Cage and Handrails In the event the owner requires easy access to the top of the unit, the unit can be furnished with ladder(s) extending from the base of the unit to the deck of the unit, as well as safety cages, and handrail packages.

A galvanized steel internal walkway is available to provide a permanent working surface for easy Ladder and Safety Cage, Handrails access to the strainer, outlet, and make-up water assembly. For access to the motor and drive assemblies on two-piece units, an internal ladder and upper service platform with handrails is available.

Internal Platform and Ladder

Internal Walkway

Vibration Cut Out Switch A factory-mounted vibration cut-out switch is available to effectively protect against equipment failure due to excessive vibration of the mechanical equipment system. BAC can provide a vibration cut-out switch in an IP65 enclosure to ensure reliable protection.

Electric Water Level Control Package The electric water level control replaces the standard mechanical make-up valve when a more precise water level control is required. This package consists of a float switch mounted in the basin and a solenoid activated valve in the make-up water line. The valve is slow closing to minimize water hammer.

... because temperature matters

Open Cooling Towers

Internal Service Platforms

S3000D - B 10

Basin Heaters

S3000D

Units exposed to below freezing ambient temperatures require protection to prevent freezing of the water in the cold water basin when the unit is idle. Factory-installed heaters, which maintain the water temperature at 4°C, are a simple and inexpensive way of providing such protection. The heater package includes the heaters, a thermostat and a low level cut out switch to protect the heaters if the water level is too low. Standard electric heaters are selected for -18°C ambient temperature.

Model No. S3000D

Heaters -18°C (kW)

S3-D240 L – S3-D379 L

2x8

S3-D412 L – S3-D527 L

2x8

S3-D473 L – S3-D672 L

2 x 12

S3-D728 L – S3-D1056 L

2 x 12

S3-D583 L – S3-D725 L

2 x 14

S3-D1132 L – S3-D1301 L

2 x 14

Extended Lubrication Lines Extended lubrication lines with grease fittings are available for lubrication of the fan shaft bearings.

Basin Sweeper Piping Basin sweeper piping provides an effective method of preventing sediment from collecting in the cold water basin of the unit. A complete piping system, including nozzles, is provided in the unit basin for connection to side stream filtration equipment. Note: For more information, please refer to the section "Technical Resources, Filtration".

Extended Lubrication Lines

Mechanical Equipment Removal System The mechanical equipment removal system is a lightweight, easy to install system for removal and installation of fan motor or gearbox. (motors upto 22kW)

Distribution Basin Covers These covers help prevent the accumulation of leaves, debris and algae in the hot water distribution basins. Mechanical Equipment Removal System

Baltimore Aircoil

S3000D - B 11

Velocity Recovery Stacks Velocity recovery stacks are available on the Series 3000D for incremental thermal performance increases. This accessory can be used to gain extra capacity in tight layouts, while maintaining the same footprint and unit kW. Field assembly is required.

... because temperature matters

Open Cooling Towers

S3000D with Velocity Recovery Stacks

S3000D - B 12

Engineering Data REMARK: Do not use for construction. Refer to factory certified dimensions & weights. This brochure includes data current at time of publication, which should be reconfirmed at the time of purchase. In the interest of product improvement, specifications, weights and dimensions are subject to change without notice. Up-to-date engineering data and more can be found at www.BaltimoreAircoil.com.

S3000D

Single Cell Units

1. Water In; 2. Overflow ND80; 3. Make-up; 4. Water Out; 5. Drain ND50; 6. Access Door; 7. S3-D728 L thru S3-D1056 L and S3-D1132 L thru S3-D1301 L ship in two sections per cell. The top section is the heaviest and tallest. Top section heights are: S3-D728 L thru S3-D970 L: 3125 mm; S3-D1132 L: 3330 mm; S3-D985 L thru S3-D1056 L: 3533 mm; S3-D1213 L: 3736 mm; S3-D1301 L: 3822mm. Model

Operating Weight (kg)

Shipping Weight (kg)

Heaviest Section (kg)

H (mm)

L1 (mm)

W (mm)

A (mm)

Fan Motor (kW)

Airflow (m3/s)

S3-D240 L S3-D272 L S3-D299 L

6706 6765 6792

3083 3142 3169

3083 3142 3169

2840 2840 2840

2584 2584 2584

5500 5500 5500

2635 2635 2635

7,5 11 15

28,1 32,0 35,0

S3-D333 L S3-D358 L S3-D379 L

7151 7164 7187

3296 3310 3332

3296 3310 3332

3247 3247 3247(3)

2584 2584 2584

5500 5500 5500

3040 3040 3040

15 18,5 22

38,4 41,2 43,7

S3-D412 L S3-D436 L

8435 8458

3823 3845

3823 3845

3247 3247(3)

2978 2978

6110 6110

3040 3040

18,5 22

46,5 49,2

S3-D455 L S3-D482 L S3-D527 L

8844 8867 8939

3968 3991 4063

3968 3991 4063

3653 3653(3) 3653(3)

2978 2978 2978

6110 6110 6110

3450 3450 3450

18,5 22 30

50,3 53,3 58,4

S3-D473 L S3-D501 L

10483 10506

4626 4649

4626 4649

3473 3473(3)

3600 3600

6566 6566

3040 3040

18,5 22

53,3 56,4

S3-D552 L S3-D604 L S3-D648 L S3-D672 L

11663 11736 11740 12285

4903 4976 4980 5530

4903 4976 4980 5530

3843(3) 3843(3) 3843(3) 3843(3)

3600 3600 3600 3600

6566 6566 6566 6566

3450 3450 3450 3450

22 30 37 45

61,1 66,8 71,7 74,4

S3-D728 L S3-D781 L S3-D828 L

14555 14560 14660

6251 6256 6351

3959 3963 4059

4920(3) 4920(3) 4920(3)

3600 3600 3600

6566 6566 6566

4715 4715 4715

30 37 45

80,2 86,0 91,1

S3-D872 L S3-D923 L S3-D970 L

15904 16004 16585

6583 6678 7264

3995 4091 4676

5733(3) 5733(3) 5923(2)

3600 3600 3600

6566 6566 6566

5530 5530 5530

37 45 55

92,6 98,1 103,2

S3-D985 L S3-D1056 L

18269 18310

7064 7105

4295 4336

6547(3) 6737(2)

3600 3600

6566 6566

6340 6340

45 55

103,1 110,6

S3-D583 L S3-D618 L S3-D676 L S3-D725 L

13756 13779 13852 13856

5480 5502 5575 5580

5480 5502 5575 5580

3653 3653(3) 3653(3) 3653(3)

4245 4245 4245 4245

7328 7328 7328 7328

3450 3450 3450 3450

18,5 22 30 37

64,5 68,4 74,8 80,3

S3-D1132 L

18746

7540

4644

5923(2)

4245

7328

5530

55

120,1

S3-D1213 L S3-D1301 L

20112 21151

7968 9007

4867 5906

6737(2) 6737(2)

4245 4245

7328 7328

6340 6340

55 75

126,4 135,7

Baltimore Aircoil

S3000D - B 13

Double Cell Units

Model

Operating Weight (kg)

Shipping Weight (kg)

Heaviest Section (kg)

H (mm)

L2 (mm)

W (mm)

A (mm)

Fan Motor (kW)

Airflow (m3/s)

S3-D240-2 L S3-D272-2 L S3-D299-2 L

13412 13530 13584

6166 6284 6338

3083 3142 3169

2840 2840 2840

5290 5290 5290

5500 5500 5500

2635 2635 2635

(2x) 7,5 (2x) 11 (2x) 15

56,2 64,0 70,0

S3-D333-2 L S3-D358-2 L S3-D379-2 L

14302 14328 14374

6592 6620 6664

3296 3310 3332

3247 3247 3247(3)

5290 5290 5290

5500 5500 5500

3040 3040 3040

(2x) 15 (2x) 18,5 (2x) 22

76,8 82,4 87,4

S3-D412-2 L S3-D436-2 L

16870 16916

7646 7690

3823 3845

3247 3247(3)

6077 6077

6110 6110

3040 3040

(2x) 18,5 (2x) 22

93,0 98,4

S3-D455-2 L S3-D482-2 L S3-D527-2 L

17688 17734 17878

7936 7982 8126

3968 3991 4063

3653 3653(3) 3653(3)

6077 6077 6077

6110 6110 6110

3450 3450 3450

(2x) 18,5 (2x) 22 (2x) 30

100,6 106,6 116,8

S3-D473-2 L S3-D501-2 L

20966 21012

9252 9298

4626 4649

3437 3437(3)

7321 7321

6566 6566

3040 3040

(2x) 18,5 (2x) 22

106,6 112,8

S3-D552-2 L S3-D604-2 L S3-D648-2 L S3-D672-2 L

23326 23472 23480 24570

9806 9952 9960 11060

4903 4976 4980 5530

3843(3) 3843(3) 3843(3) 3843(3)

7321 7321 7321 7321

6566 6566 6566 6566

3450 3450 3450 3450

(2x) 22 (2x) 30 (2x) 37 (2x) 45

122,2 133,6 143,4 148,8

S3-D728-2 L S3-D781-2 L S3-D828-2 L

29110 29120 29320

12502 12512 12702

3959 3963 4059

4920(3) 4920(3) 4920(3)

7321 7321 7321

6566 6566 6566

4715 4715 4715

(2x) 30 (2x) 37 (2x) 45

160,4 172,0 182,2

S3-D872-2 L S3-D923-2 L S3-D970-2 L

31808 32008 33170

13166 13356 14528

3995 4091 4676

5733(3) 5733(3) 5923(2)

7321 7321 7321

6566 6566 6566

5530 5530 5530

(2x) 37 (2x) 45 (2x) 55

185,2 196,2 206,4

S3-D985-2 L S3-D1056-2 L

36538 36620

14128 14210

4295 4336

6547(3) 6737(2)

7321 7321

6566 6566

6340 6340

(2x) 45 (2x) 55

206,2 221,2

S3-D583-2 L S3-D618-2 L S3-D676-2 L S3-D725-2 L

27512 27558 27704 27712

10960 11004 11150 11160

5480 5502 5575 5580

3653 3653(3) 3653(3) 3653(3)

8610 8610 8610 8610

7328 7328 7328 7328

3450 3450 3450 3450

(2x) 18,5 (2x) 22 (2x) 30 (2x) 37

129,0 136,8 149,6 160,6

S3-D1132-2 L

37492

15080

4644

5923(2)

8610

7328

5530

(2x) 55

240,2

4867 5906

6737(2) 6737(2)

8610 8310

7328 7328

6340 6340

(2x) 55 (2x) 75

252,8 271,4

S3-D1213-2 L S3-D1301-2 L

40224 42302

15936 18014

... because temperature matters

Open Cooling Towers

1. Water In; 2. Overflow; 3. Make-up; 4. Water Out; 5. Drain ND50; 6. Access Door; 7. S3-D728 L thru S3-D1056 L and S3-D1132 L thru S3D1301 L ship in two sections per cell. The top section is the heaviest and tallest. Top section heights are: S3-D728 L thru S3-D970 L: 3125 mm; S3-D1132 L: 3330 mm; S3-D985 L thru S3-D1056 L: 3533 mm; S3-D1213 L: 3736 mm; S3-D1301 L: 3822mm.

S3000D - B 14

General Notes 1. Operating weight is for tower with the water level in the cold water basin at overflow. If a lower operating weight is needed to meet design requirements, your local BAC Balticare Sales Representative can provide additional assistance.

S3000D

2. Heights are for units with belt drive, except for models with motor of 55 kW and larger where gear drive is standard (= S3-D970 L, S3-D1056 L, S3-D1132 L, S3-D1213 L and S3D-1301 L).

3. Models with motors of 22 to 45 kW are shipped with an optional gear drive and may have heights up to 190 mm greater than shown. 4. Models with optional Whisper Quiet Fan may have heights up to 1000 mm greater than shown. 5. Models with an optional Velocity Recovery Stack can be up to 1500 mm higher.

Connection Sizes

Model S3000

Top Inlet (mm)

Water Outlet (mm)

Make-Up (mm)

F (mm)

G (mm)

J (mm)

S3-D240 L S3-D272 L S3-D299 L

(2x) ND 150 (2x) ND 150 (2x) ND 150

(1x) ND 200 (1x) ND 200 (1x) ND 200

ND 25 ND 25 ND 25

6 6 6

1292 1292 1292

2706 2706 2706

S3-D333 L S3-D358 L S3-D379 L

(2x) ND 150 (2x) ND 150 (2x) ND 150

(1x) ND 200 (1x) ND 200 (1x) ND 200

ND 25 ND 25 ND 25

6 6 6

1292 1292 1292

2706 2706 2706

S3-D412 L S3-D436 L

(2x) ND 150 (2x) ND 150

(1x) ND 200 (1x) ND 200

ND 40 ND 40

30 30

1489 1489

3099 3099

S3-D455 L S3-D482 L S3-D527 L

(2x) ND 150 (2x) ND 150 (2x) ND 150

(1x) ND 250 (1x) ND 250 (1x) ND 250

ND 40 ND 40 ND 40

30 30 30

1489 1489 1489

3099 3099 3099

S3-D473 L S3-D501 L

(2x) ND 200 (2x) ND 200

(1x) ND 250 (1x) ND 250

ND 40 ND 40

30 30

1800 1800

3721 3721

S3-D552 L S3-D604 L S3-D648 L S3-D672 L

(2x) ND 200 (2x) ND 200 (2x) ND 200 (2x) ND 200

(1x) ND 250 (1x) ND 250 (1x) ND 250 (1x) ND 250

ND 40 ND 40 ND 40 ND 40

30 30 30 30

1800 1800 1800 1800

3721 3721 3721 3721

S3-D728 L S3-D781 L S3-D828 L

(2x) ND 200 (2x) ND 200 (2x) ND 200

(1x) ND 300 (1x) ND 300 (1x) ND 300

ND 40 ND 40 ND 40

30 30 30

1800 1800 1800

3721 3721 3721

S3-D872 L S3-D923 L S3-D970 L

(2x) ND 200 (2x) ND 200 (2x) ND 200

(1x) ND 300 (1x) ND 300 (1x) ND 300

ND 40 ND 40 ND 40

30 30 30

1800 1800 1800

3721 3721 3721

S3-D985 L S3-D1056 L

(2x) ND 200 (2x) ND 200

(1x) ND 300 (1x) ND 300

ND 40 ND 40

30 30

1800 1800

3721 3721

S3-D583 L S3-D618 L S3-D676 L S3-D725 L

(2x) ND 200 (2x) ND 200 (2x) ND 200 (2x) ND 200

(1x) ND 250 (1x) ND 300 (1x) ND 300 (1x) ND 300

ND 40 ND 40 ND 40 ND 40

15 15 15 15

2116 2116 2116 2116

5010 5010 5010 5010

S3-D1132 L

(2x) ND 250

(1x) ND 350

ND 50

15

2116

5010

S3-D1213 L S3-D1301 L

(2x) ND 250 (2x) ND 250

(1x) ND 350 (1x) ND 350

ND 50 ND 50

15 15

2116 2116

5010 5010

Notes: 1. Top inlet connections are flange stud circles. All other connections ND100 and smaller are MPT. Connections larger than ND100 are beveled for welding.

2. On double cell units, connections are the same size but are located on both ends of the unit.

Baltimore Aircoil

S3000D - B 15

Sound Attenuation S3-D240 L through S3-D725 L

Model No.

Fan Motor (kW)

A (mm)

B (mm)

Ht (mm)

Weight Discharge Attenuator (kg) (1)

Weight Intake Attenuator (kg) (2) (3)

S3-D240 L S3-D272 L S3-D299 L

7,5 11 15

2578 2578 2578

1715 1715 1715

3946 3946 3946

350 350 350

340 340 340

S3-D333 L S3-D358 L S3-D379 L

15 18,5 22

2578 2578 2578

2121 2121 2121

4351 4351 4351

350 350 350

420 420 420

S3-D412 L S3-D436 L

18,5 22

3035 3035

2121 2121

4351 4351

400 400

480 480

S3-D455 L S3-D482 L S3-D527 L

18,5 22 30

3035 3035 3035

2527 2527 2527

4761 4761 4761

400 400 400

570 570 570

S3-D473 L S3-D501 L

18,5 22

3340 3340

2121 2121

4351 4351

460 460

580 580

S3-D552 L S3-D604 L S3-D648 L S3-D672 L

22 30 37 45

3340 3340 3340 3340

2527 2527 2527 2527

4761 4761 4761 4761

460 460 460 460

690 690 690 690

S3-D583 L S3-D618 L S3-D676 L S3-D725 L

18,5 22 30 37

3645 3645 3645 3645

2527 2527 2527 2527

4761 4761 4761 4761

550 550 550 550

810 810 810 810

... because temperature matters

Open Cooling Towers

1. Intake Attenuator; 2. Discharge Attenuator; L=Unit Length; W=Unit Width (see engineering data).

S3000D - B 16

S3000D

Sound Attentuation S3-D728 L through S3-D1301 L

1. Intake Sound Attenuation; 2. Discharge Attenuation; L = Unit Length; W = Unit Width (see engineering data).

Model No.

Fan Motor (kW)

A (mm)

B1 (mm)

B2 (mm)

Ht

Weight Discharge Attenuator (1) (kg)

Weight Lower Intake Attenuator (both) (2) (3) (kg)

Weight Upper Intake Attenuator(both) (2) (3) (kg)

S3-D728 L S3-D781 L S3-D828 L

30 37 45

3645 3645 3645

994 994 994

2353 2353 2353

6026 6026 6026

480 480 480

270 270 270

640 640 640

S3-D872 L S3-D923 L S3-D970 L

37 45 55

3645 3645 3645

1807 1807 1807

2353 2353 2353

6841 6841 6841

480 480 480

500 500 500

640 640 640

S3-D985 L S3-D1056 L

45 55

3645 3645

2213 2213

2353 2353

7651 7651

480 480

500 500

750 750

S3-D1132L

55

4255

1807

2353

6841

570

580

750

S3-D1213L S3-D1301L

55

4255 4255

2213 2213

2759 2759

7651 7651

570 570

710 710

880 880

General Notes Sound Attenuation 1. Discharge attenuator is shipped in one piece, not installed.

3. Weight of intake attenuator is total for both attenuators.

2. Intake attenuators are shipped installed for single cell units. For 2 or more cells, consult BAC Balticare Representative.

4. For correct layout and piping considerations, please refer to your local BAC Balticare representative.

Remote Sump Data Refer to the "Technical Resources" section "Selection of Remote Sump" for Remote Sump Data.

Baltimore Aircoil

S3000D - B 17

Structural Support REMARK: Do not use for construction. Refer to factory certified dimensions & weights. This brochure includes data current at time of publication, which should be reconfirmed at the time of purchase. In the interest of product improvement, specifications, weights and dimensions are subject to change without notice. Up-to-date engineering data and more can be found at www.BaltimoreAircoil.com.

Units with and without Sound Attenuation Single Cell Unit – Plan A

1. Outline of unit; 2. Air Inlet Side; 3. Mounting Holes (Ø 22 mm); 4. Access for Mounting holes required; 5. Additional Anchor Bolts (see note 7).

... because temperature matters

Open Cooling Towers

The recommended support arrangement for the Series 3000D Cooling Tower, consists of parallel I-beams positioned as shown in the drawings. Besides providing adequate support, the steel also serves to raise the unit above any solid foundation to assure access to the bottom of the tower. The Series 3000D may also be supported on columns at the anchor bolt locations as shown the following Plan. A minimum bearing surface of 100 cm must be provided under each of the concentrated load points (See Note 6 following page). To support a Series 3000D Cooling Tower on columns, or in an alternate steel support arrangement, consult your BAC Balticare Representative.

S3000D - B 18

S3000D

Single Cell Unit – Plan B

1. Outline of unit; 2. Air Inlet Side; 3. Mounting Holes (Ø 22mm); 4. Acces for Mounting Holes Required.

Double Cell Unit – Plan C

1. Outline of unit; 2. Air Inlet Side; 3. Mounting Holes (Ø 22mm); 4. Acces for Mounting Holes Required.

Baltimore Aircoil

S3000D - B 19

Double Cell Unit – Plan D

Model No.

Operating Weight (1) (kg)

Shipping Weight (1)(2) (kg)

Weight at bolt hole location (1)(2) (kg)

Length (L1) (mm)

Length (L2) (mm)

Width (W) (mm)

A (mm)

B (mm)

C (mm)

D (mm)

E (mm)

S3-D240 L S3-D272 L S3-D299 L

6706 6765 6792

3083 3142 3169

1677 1691 1698

2584 2584 2584

5288 5288 5288

5500 5500 5500

3100 3100 3100

4835 4835 4835

29 29 29

2526 2526 2526

178 178 178

S3-D333 L S3-D358 L S3-D379 L

7151 7164 7187

3296 3310 3332

1788 1791 1797

2584 2584 2584

5288 5288 5288

5500 5500 5500

3100 3100 3100

4835 4835 4835

29 29 29

2526 2526 2526

178 178 178

S3-D412 L S3-D436 L

8435 8458

3823 3845

2109 2115

2978 2978

6076 6076

6110 6110

4731 4731

5445 5445

29 29

2920 2920

178 178

S3-D455 L S3-D482 L S3-D527 L

8844 8867 8939

3968 3991 4063

2211 2217 2235

2978 2978 2978

6076 6076 6076

6110 6110 6110

4731 4731 4731

5445 5445 5445

29 29 29

2920 2920 2920

178 178 178

S3-D473 L S3-D501 L

10483 10506

4626 4649

2621 2627

3600 3600

7320 7320

6566 6566

3445 3445

5902 5902

29 29

3542 3542

178 178

S3-D552 L S3-D604 L S3-D648 L S3-D672 L

11663 11736 11740 12285

4903 4976 4980 5530

2916 2934 2935 3071

3600 3600 3600 3600

7320 7320 7320 7320

6566 6566 6566 6566

3445 3445 3445 3445

5902 5902 5902 5902

29 29 29 29

3542 3542 3542 3542

178 178 178 178

S3-D728 L S3-D781 L S3-D828 L

14555 14560 14660

6251 6256 6351

3639 3640 3665

3600 3600 3600

7320 7320 7320

6566 6566 6566

3445 3445 3445

5902 5902 5902

29 29 29

3542 3542 3542

178 178 178

S3-D872 L S3-D923 L S3-D970 L

15904 16004 16585

6583 6678 7264

3976 4001 4146

3600 3600 3600

7320 7320 7320

6566 6566 6566

3445 3445 3445

5902 5902 5902

29 29 29

3542 3542 3542

178 178 178

S3-D985 L S3-D1056 L

18269 18310

7064 7105

4567 4578

3600 3600

7320 7320

6566 6566

3445 3445

5902 5902

29 29

3542 3542

178 178

... because temperature matters

Open Cooling Towers

1. Outline of unit, 2. Air Inlet Side; 3. Mounting Holes(Ø 22 mm); 4. Access for Mounting Holes required; 5. Additional Anchor Bolts (see note 7).

S3000D

S3000D - B 20

Model No.

Operating Weight (1) (kg)

Shipping Weight (1)(2) (kg)

Weight at bolt hole location (1)(2) (kg)

Length (L1) (mm)

Length (L2) (mm)

Width (W) (mm)

A (mm)

B (mm)

C (mm)

D (mm)

E (mm)

S3-D583 L S3-D618 L S3-D676 L S3-D725 L

13756 13779 13852 13856

5480 5502 5575 5580

3439 3445 3463 3464

4245 4245 4245 4245

8610 8610 8610 8610

7328 7328 7328 7328

3654 3654 3654 3654

6664 6664 6664 6664

43 43 43 43

4159 4159 4159 4159

206 206 206 206

S3-D1132 L

18746

7540

4687

4245

8610

7328

3654

6664

43

4159

206

S3-D1213 L S3-D1301 L

20112 21151

7968 9007

5028 5288

4245 4245

8610 8610

7328 7328

3654 3654

6664 6664

43 43

4159 4159

206 206

Notes: 1. Weights are for a single cell. To obtain weights for multi-cell units, multiply by the number of cells. 2. Operating weight and weight loading are for a single cell tower with water at overflow level in the cold water basin. 3. Support beams and anchor bolts to be selected and installed by parties other than BAC. 4. All support steel must be level at the top.

5. Beams must be selected in accordance with accepted structural practice. Maximum deflection of beam under unit to be 1/360 of span, not to exceed 12 mm. 6. If point vibration isolation is used with multi-cell towers, the isolators must be located under the support steel, not between the support steel and the cooling towers. 7. 4 holes required for models S3-D240 L through S3-D725 L. 8 holes required for models S3-D728 L through S3-D1301 L. The 4 additional anchor bolts, for models S3-D728 L through S3-D1301 L, are located 114 mm towards the inside of the unit.

Baltimore Aircoil

S3000D - B 21

Engineering Specifications 1.0 Cooling Tower steel prepared in a four-step (clean, pre-treat, rinse, dry) process with an electrostatically sprayed, thermosetting, hybrid polymer fusebonded to the substrate during a thermally activated curing stage and monitored by a 23-step quality assurance program. Casing panels shall be constructed of corrosion and UV-resistant fibreglass reinforced polyester (FRP) to minimise maintenance requirements and prolong equipment life.

1.2 Thermal Capacity: The cooling tower(s) shall be warranted by the manufacturer to cool _____ l/s of water from ______ °C to _____°C at _____°C entering wet-bulb temperature.

(Alternate 1.3) Type 304 or 316 Stainless Steel Construction: All structural members, including the structural frame, hot and cold water basins, distribution covers and fan deck shall be constructed of Type 304 or 316 stainless steel and assembled with stainless steel nut and bolt fasteners. Fan cylinder shall be galvanised steel protected with the Baltibond® Corrosion Protection System. Casing panels shall be constructed of corrosion and UV-resistant fibreglass reinforced polyester (FRP) to minimise maintenance requirements and prolong equipment life.

1.3 Corrosion Resistant Construction (standard): Unless otherwise noted in this specification, all structural members shall be constructed of heavy-gauge Z600 metric hot-dip galvanised steel with all edges given a protective coating of zinc-rich compound. All external surfaces are protected with the BALTIPLUS Corrosion Protection. Casing panels shall be constructed of corrosion and UV-resistant fibreglass reinforced polyester (FRP) to minimise maintenance requirements and prolong equipment life. (Alternate 1.3) Corrosion Resistant Construction (optional): Unless otherwise noted in this specification, all structural members shall be protected with the BALTIBOND® Corrosion Protection System. The system shall consist of Z600 metric hot-dip galvanised

1.4 Quality Assurance: The cooling tower manufacturer shall have a Management System certified by an accredited registrar as complying with the requirements of ISO-9001:2000 to ensure consistent quality of products and services. 1.5 Warranty: The manufacturer’s standard equipment warranty shall be for a period of not less than one year from date of startup or eighteen months from date of shipment, whichever occurs first.

2.0 Construction Details 2.1 Structure: The cooling tower shall be constructed with a sturdy structural frame designed to transmit all wind and mechanical loads to the equipment anchorage. The frame shall be constructed of heavy-gauge steel angles and channels. 2.2 Casing Panels: Casing panels shall be constructed of corrosion and UV-resistant fibreglass reinforced polyester (FRP) to minimise maintenance requirements and prolong equipment life. 2.3 Cold Water Basin: The cold water basin shall be constructed of heavy-gauge steel panels and structural members. The basin shall include a sloping depressed section with drain/clean-out connection. The basin area under the wet deck surface shall be sloped toward the depressed section to facilitate cleaning. Standard basin accessories shall include a brass make-up valve with a large diameter plastic float for easy adjustment of operating water level. (Alternate 2.3) Cold Water Basin: The cold water basin shall be constructed of heavy-gauge Type 304 or 316 stainless steel panels and structural members. The basin shall include a depressed centre

section with drain/clean-out connection. The basin area under the wet deck surface shall be sloped toward the depressed section to facilitate cleaning. Standard basin accessories shall include a brass make-up valve with a large diameter plastic float for easy adjustment of operating water level. 2.4 Water Outlet: The cooling tower basin outlet shall be beveled for welding. The outlet shall be provided with large area lift out strainers with perforated openings sized smaller than the water distribution nozzles and an anti-vortexing device to prevent air entrainment. The strainer and vortex device shall be constructed of the same materials as the cold water basin to prevent dissimilar metal corrosion. 2.5 Water Distribution System: Hot water distribution basins shall be the open gravity type and constructed of heavy-gauge Z600 hotdip galvanized steel. Basin weirs and plastic metering orifices shall be provided to ensure even distribution of water over the wet deck surface. Lift-off distribution covers shall be constructed of heavygauge Z600 metric hot-dip galvanized steel.

3.0 Mechanical Equipment 3.1. Fan(s): Fan(s) shall be heavy-duty, axial flow with aluminum alloy blades selected to provide optimum cooling tower thermal performance with minimal sound levels. Air shall discharge through a fan cylinder designed for streamlined air entry and minimum tip clearance for maximum fan efficiency. The top of the fan cylinder shall be equipped with a conical, non-sagging removable fan guard. (Alternate 3.1) Fan(s): Fan(s) shall be of “Whisper Quiet” fan design for ultra low sound consisting of multi-blade aerofoil fan design constructed of fibreglass reinforced plastic blades. 3.2. Bearings: Fan(s) and shaft(s) shall be supported by heavy-duty, self-aligning, grease-packed ball bearings with moisture proof seals

and integral slinger collars, designed for a minimum L10 life of 40 000 hours (280 000 Hr. Avg. Life). 3.3. Fan Drive: The fan(s) shall be belt driven with taper lock sheaves. The belts shall be constructed of neoprene reinforced polyester cord and be specifically designed for cooling tower service. 3.4. Sheaves: Fan and motor sheave(s) shall be fabricated from corrosion-resistant materials to minimize maintenance and ensure maximum drive and powerband operating life. 3.5. Fan Motor: Fan motor(s) shall be totally enclosed fan cooled (TEFC), reversible, squirrel cage, ball bearing type designed specifically for cooling tower service. The motor shall be furnished with special moisture protection on windings, shafts and bearings.

4.0 BACross II Wet Deck Surface and Integral Drift Eliminators 4.1 BACross II Wet Deck Surface and Drift Eliminators: The wet deck surface and integral drift eliminators shall be formed from selfextinguishing plastic material and shall be impervious to rot, decay, fungus and biological attack. The wet deck shall be suitable for

entering water temperatures up to 50°C. The wet deck surface shall be manufactured, tested, and rated by the cooling tower manufacturer and shall be elevated above the cold water basin to facilitate cleaning.

... because temperature matters

Open Cooling Towers

1.1 General: Furnish and install _____ factory-assembled, induceddraft, axial fan, crossflow cooling tower(s) with vertical air discharge, conforming in all aspects to the specifications, schedules and as shown on the plans. Overall dimensions shall not exceed approximately _____ mm long x ______ mm wide x _____ mm high. The total connected fan kW shall not exceed _____ kW. The cooling tower(s) shall be Baltimore Aircoil Model ____________.

S3000D - B 22

5.0 Combined Inlet Shield Technology 5.1. Combined Inlet Shields: Combined inlet shields shall be separate from the wet deck surface and removable to allow easy access for inspection of the air/water interface at the air inlet side of the equipment. Combined inlet shields shall prevent UV-light and

debris from entering the unit, as well as prevent water splash out during fan cycling. They shall be constructed of maintenance free, corrosion and UV resistant material.

6.0 Access

S3000D

6.1 Plenum Access: Two hinged access doors shall be provided for access into the plenum section.

7.0 Sound 7.1 Sound Level: To maintain the quality of the local environment, the maximum sound pressure levels (dB) measured 15 m from the cooling tower operating at full fan speed shall not exceed the sound levels detailed below.

Location

63

125

250

(Alternate) 7.1 Sound Level: To maintain the quality of the local environment, the cooling tower shall be furnished with an extremely low sound fan Type “Whisper Quiet”. Maximum sound pressure levels (dB) measured 15 m from the cooling tower operating at full fan speed shall not exceed the sound levels detailed below.

500

Discharge Air Inlet End

Baltimore Aircoil

1000

2000

4000

8000

dB(A)

TXV - B 1

TXV

Open Cooling Towers

Open Cooling Towers

Product Detail TXV Open Cooling Tower ........................................................................ B2 Benefits ....................................................................................................... B4 Construction Details .................................................................................. B6 Custom Features and Options .................................................................. B7 Accessories ................................................................................................. B9 Engineering Data ...................................................................................... B11 Structural Support .................................................................................. B14 Engineering Specifications ..................................................................... B15

TXV - B 2

TXV Open Cooling Tower Capacity Single Cell Capacity:

TXV

10 - 128 l/s

General Description Series 1500 Cooling Towers minimize the operating, installation, and maintenance costs associated with both new and replacement cooling tower projects. The Series 1500 delivers fully rated thermal performance over a wide range of flow and temperature requirements. Standard design features minimize the costs associated with enclosures, support requirements, electrical service, piping, and rigging.

Key Features z

Ideal replacement unit

z

Single side air inlet

z

Low energy consumption

z

Low installed cost

z

Easy maintenance

z

Reliable year-round operation

z

Long service life

Baltimore Aircoil

TXV - B 3

Open Cooling Towers

... because temperature matters

TXV - B 4

Benefits Ideal Replacement Unit

TXV

z

z

z

Support Steel – Units are designed to mount directly on the existing support steel of many cooling towers (both cross flow and counter flow). Electrical Service – Fan motor configurations can be supplied to match existing wiring. Enclosures – Units fit in most existing enclosures with little or no modifications due to the single air inlet design. Single air inlet provides installation flexibility in tight layouts

Counterflow CoolingTower Replacement

Replaced by Crossflow units

Low Energy Consumption z

z

Evaporative Cooling Equipment minimizes the energy consumption of the entire system because it provides lower operating temperatures. The owner saves money while conserving natural resources and reducing environmental impact. TXV provides heat rejection at the lowest possible energy input and maintenance requirements via: - High efficiency, low kW axial fans - High efficiency BACross® Wet Deck, which provides maximum air/water contact time at low air pressure drops - Multiple Fan Motor System: independent fan motor and drive assembly per fan, which allows extra steps of capacity control.

Baltimore Aircoil

TXV - B 5

Low Installed Cost z

z

Modular Design – The modular design minimizes the size and weight of the heaviest lift, allowing for the use of smaller, less costly cranes. Modular Design – All models mount directly on parallel I-beams and ship complete with motors and drives factory-installed and aligned.

The unit shown ships in two pieces to minimize shipping and rigging costs

Easy Maintenance z

z

z

Easy Cleaning – The wet deck surface is elevated above the sloped cold water basin floor to facilitate flushing of dirt and debris from this critical area. Hinged Access Doors and Standard Internal Walkway – Provide easy entry to the spacious plenum for routine drive maintenance. Accessibility – Make-up, drain, overflow and optional basin accessories are accessible from outside the unit.

Reliable Year-Round Operation z

z

Belt Drive System utilizes special corrosion-resistant materials of construction and state-ofthe-art technology to ensure ease of maintenance and reliable year-round performance. Combined Inlet Shields prevent biological growth from sunlight, act as a filter for air borne impurities and debris and eliminate water splash out.

Long Service Life z

Materials of Construction – Various materials are available to meet the corrosion resistance, unit operating life, and budgetary requirements of any project.

Note: For more information, please refer to the section “Technical Resources, Materials of Construction”.

... because temperature matters

Open Cooling Towers

z

Single Side Air Inlet – Units can be placed close to solid walls, reducing the size of enclosures and allowing for more profitable use of premium space.

TXV - B 6

TXV

Construction Details

1. Heavy-Duty Construction z

Z600 hot-dip galvanized steel panels

5. BACross® Wet Deck Surface with Integral Drift Eliminators (Not Shown) z

Plastic material

2. Fan Drive System z

Premium quality belts

z

Impervious to rot, decay and biological attack

z

Corrosion resistant sheaves

z

Designed and manufactured by BAC

z

Heavy-duty bearings

6. Combined Inlet Shields

z

Adapted fan motor for operation in saturated conditions.

3. Low kW Axial Fan(s)

z

Corrosion Resistant

z

Easily removable

z

UV resistant plastic material

z

Quiet operation

z

High Efficiency

z

Sloped cold water basin for easy cleaning

z

Corrosion resistant aluminum

z

Suction strainer with anti-vortex hood

4. Water Distribution System

z

7. Cold Water Basin

Adjustable water make-up assembly from air inlet side

z

Steel covers in easy to remove sections

z

Low pump head gravity distribution basin

z

z

Large orifice, non-clog nozzles

8. Hinged Access Doors

z

Integral strainer

z

Baltimore Aircoil

Integral internal walkway as standard Inward swinging door

TXV - B 7

Custom Features and Options Construction Options z

z

Standard Construction: Steel panels and structural elements are constructed of Z600 heavy-gauge hot-dip galvanized steel protected with the Baltiplus Corrosion Protection on the outside of the unit.

z

Optional Stainless Steel Construction: Steel panels and structural elements are constructed of stainless steel either type 304 or 316.

z

Optional Water-Contact Stainless Steel Cold Water Basin: A cost-effective alternative to an all stainless steel unit. The critical components in the cold water basin and the cold water basin itself are provided in stainless steel. The remaining components are protected with the BALTIBOND® Corrosion Protection System.

Note: See section Technical Resources, Material of Construction for more details on the materials described above.

Multiple Fan Drive System All TXV-models are standard equipped with the multiple fan motor system. This system consists of an independent fan motor and drive assembly per fan with a plenum partition to allow independent operation of each fan. This standard feature provides 2 steps of capacity control on dual fan units and 3 steps of capacity control on triple fan units, as illustrated below.

Individual Motor and Drive on each Fan

Extra Steps of Capacity Control

Removable Bundled Fill For installations where it is necessary or recommended to remove the wet deck surface for more thorough cleaning and disinfection, removable bundled fill is available. The fill bundles can be easily lifted and handled by one person and therefore provide a simple and secure method of removing and installing. The bundles can be dismantled and sheet by sheet can be removed for inspection and cleaning of both sides. After cleaning the sheets can be re-bundled and re-installed.

Easy Removable Fill Bundles

... because temperature matters

Open Cooling Towers

Optional BALTIBOND® Corrosion Protection System: The BALTIBOND® Corrosion Protection System, a hybrid polymer coating used to extend equipment life, is applied before assembly to all hot-dip galvanized steel components of the unit.

TXV - B 8

TXV

Low Sound Operation The low sound levels generated by Series 1500 Units, thanks to the use of high efficiency low noise fans as standard, make them suitable for installation in most environments. For very sound sensitive installations all models are also available with a “Whisper Quiet” sound fan option that significantly reduces the sound levels generated from the tower with minimal impact on thermal performance. For extremely sound sensitive installations, factory designed, tested and rated sound attenuation is available for both the air inlet and discharge.

Sound Attenuators on TXV Cooling Tower

Note: For more information, please refer to the section “Technical Resources, Sound Reduction Options”.

Remote Sump Execution The use of an auxiliary sump within a heated space is the most satisfactory way to protect sump water from freezing. When the circulating pump is shut off, all the water in the water distribution, in suspension and in the sump will drain freely to the auxiliary sump. Note: For detailed information on the calculation of the remote sump tank, please refer to the section "Technical Resources, Selection of Remote Sump Tank".

Combined Inlet Shields Combined Inlet shields prevent biological growth from sunlight, act as a filter for air borne impurities and debris and eliminate water splash out.

High Temperature Wet Deck If operation above 50°C is anticipated, an optional high temperature wet deck material is available which increases the maximum allowable entering water temperature to 55°C.

Combined Inlet Shields

Baltimore Aircoil

TXV - B 9

Accessories Ladder, Safety Cage and Handrails In the event the owner requires easy access to the top of the unit, the unit can be furnished with ladder(s) extending from the base of the unit to the deck of the unit, as well as safety cages, and handrail packages.

For access to the motor and drive assemblies internal ladders are available on models TXV-292 up to TXV-500 and TXV-310 up to TXV-425.

Internal Service Platforms For access to the motor and drive assemblies on models TXV-292 up to TXV-500 and TXV-310 up to TXV-425 an upper service platform with ladder and handrails is available.

Internal Walkway and Large, Hinged Access Door

External Service Platform, Ladder and Safety Cage

Internal Ladder and Service Platform

Electric Water Level Control Package The electric water level control replaces the standard mechanical make-up valve when a more precise water level control is required. This package consists of a float switch mounted in the basin and a solenoid activated valve in the make-up water line. The valve is slow closing to minimize water hammer.

... because temperature matters

Open Cooling Towers

Internal Ladder

TXV - B 10

Basin Heaters

TXV

Units exposed to below freezing ambient temperatures require protection to prevent freezing of the water in the cold water basin when the unit is idle. Factory-installed heaters, which maintain the water temperature at 4°C, are a simple and inexpensive way of providing such protection. The heater package includes the heaters, a thermostat and a low level cut out switch to protect the heaters if the water level is too low. Standard electric heaters are selected for -18°C ambient temperature.

Model No. TXV

Heater -18°C (kW)

TXV 109 - 154

1x6

TXV 177 - 193

1x6

TXV 217 - 237

1x8

TXV 292 - 333

1x8

TXV 354 - 500

2x6

TXV 310 - 425

2x6

Extended Lubrication Lines Extended lubrication lines with grease fittings are available for lubrication of the fan shaft bearings.

Distribution Basin Covers These covers prevent the accumulation of leaves, debris and algae in the hot water distribution pans.

Extended Lubrication Lines

Basin Sweeper Piping Basin sweeper piping provides an effective method of preventing sediment from collecting in the cold water basin of the unit. A complete piping system, including nozzles, is provided in the unit basin for connection to side stream filtration equipment. Note: For more information, please refer to the section "Technical Resources, Filtration".

Basin Sweeper Piping

Baltimore Aircoil

TXV - B 11

Engineering Data REMARK: Do not use for construction. Refer to factory certified dimensions & weights. This brochure includes data current at time of publication, which should be reconfirmed at the time of purchase. In the interest of product improvement, specifications, weights and dimensions are subject to change without notice. Up-to-date engineering data and more can be found at www.BaltimoreAircoil.com.

Open Cooling Towers

TXV 109 - TXV 237

1. Water in; 2. Water out; 3. Make Up; 4. Overflow ND80; 5. Drain ND50; 6.Access Door.

Model No. TXV

Operating Weight (kg)

Shipping Weight (kg)

Heaviest Section (kg)

H (mm)

L (mm)

W (mm)

Air Flow (m3/s)

Fan Motor (kW)

Fluid Inlet ND (mm)

Fluid Outlet ND (mm)

Make Up ND (mm)

TXV 109 TXV 135 TXV 154

3040 3070 3090

1640 1670 1690

1640 1670 1690

3150 3150 3150

2775 2775 2775

2385 2385 2385

16,4 20,8 23,8

(2x) 2,2 (2x) 4,0 (2x) 5,5

150 150 150

200 200 200

25 25 25

TXV 177 TXV 193

3780 3790

1910 1920

1910 1920

3150 3150

3690 3690

2385 2385

27,1 29,8

(2x) 5,5 (2x) 7,5

150 150

200 200

25 25

TXV 217 TXV 237

4600 4610

2290 2300

2290 2300

3150 3150

3690 3690

2985 2985

30,8 33,9

(2x) 5,5 (2x) 7,5

200 200

200 200

40 40

... because temperature matters

TXV - B 12

TXV

TXV 292 - TXV 500

1. Water in; 2. Water out; 3. Make Up; 4. Overflow ND80; 5. Drain ND50; 6.Access door.

Model TXV

Operating Weight (kg)

Shipping Weight (kg)

Heaviest Section (kg)

H (mm)

L (mm)

W (mm)

Air Flow (m3/s)

Fan Motor (kW)

Fluid Inlet ND (mm)

Fluid Outlet ND (mm)

Make Up ND (mm)

TXV 292 TXV 314 TXV 333

6090 6110 6130

3100 3120 3140

1720 1740 1760

4385 4385 4385

3690 3690 3690

2985 2985 2985

39,1 42,1 45,6

(2x) 7,5 (2x) 9,0 (2x) 11,0

250 250 250

250 250 250

40 40 40

TXV 354 TXV 402 TXV 441 TXV 500

8560 8570 8610 8710

4040 4050 4080 4180

2260 2270 2300 2400

4525 4525 4525 4525

5520 5520 5520 5520

2985 2985 2985 2985

46,6 53,4 58,8 67,7

(3x) 4,0 (3x) 5,5 (3x) 7,5 (3x) 11,0

250 250 250 250

250 250 250 250

40 40 40 40

TXV 310 - TXV 425

1. Water in; 2. Water out; 3. Make Up; 4. Overflow ND80; 5. Drain ND50; 6.Access Door.

Baltimore Aircoil

TXV - B 13

Model No. TXV

Operating Weight (kg)

Shipping Weight (kg)

Heaviest Section (kg)

H (mm)

L (mm)

W (mm)

Air Flow (m3/s)

Fan Motor (kW)

Fluid Inlet ND (mm)

Fluid Outlet ND (mm)

Make Up ND (mm)

TXV 310 TXV 340 TXV 365 TXV 385 TXV 425

7160 7170 7200 7210 7310

3370 3380 3400 3410 3510

1770 1780 1800 1810 1910

4790 4790 4790 4790 4790

3690 3690 3690 3690 3690

3610 3610 3610 3610 3610

38,3 42,1 45,4 48,2 53,1

(2x) 5,5 (2x) 7,5 (2x) 9,0 (2x) 11 (2x) 15

250 250 250 250 250

250 250 250 250 250

40 40 40 40 40

General Notes 3. Models TXV 292 up to 333, TXV 354 up to 500 and TXV 310 up to 425 are shipped in two sections per cell. The top section is the heaviest and has a height of 2130 mm.

2. Make-up, overflow, suction, and drain connections can be provided on end opposite to that shown; consult your BAC Balticare representative.

Sound Attenuation

1. Intake Attenuator; 2. Discharge Attenuator.

Model No

Dimensions (mm)

Weight (kg)

TXV

D

Ht

Intake

Discharge

TXV 109- 154

1345

3885

190

210

TXV 177 - 193

1345

3885

250

255

TXV 217 - 237

1665

3885

250

270

TXV 292 - 333

1665

5120

400

270

TXV 354 - 500

1500

5260

600

385

TXV 310 - 425

2005

5525

450

310

Models TXV 292 up to 333, TXV 354 up to 500 and TXV 310 up to TXV 425: intake attenuators ship in two sections. Indicated weights are total weights of two sections. W = Unit Width, see general Engineering Data.

Remote Sump Data Refer to the "Technical Resources" section "Selection of Remote Sump" for Remote Sump Data.

... because temperature matters

Open Cooling Towers

1. All connections 100 mm and smaller are MPT. Connections 125 mm and larger are bevelled-for-welding.

TXV - B 14

Structural Support REMARK: Do not use for construction. Refer to factory certified dimensions & weights. This brochure includes data

TXV

current at time of publication, which should be reconfirmed at the time of purchase. In the interest of product improvement, specifications, weights and dimensions are subject to change without notice. Up-to-date engineering data and more can be found at www.BaltimoreAircoil.com. The recommended support arrangement for units consists of parallel I-beams running the full length of the unit, spaced as shown in the following drawing. Besides providing adequate support, the steel also serves to raise the unit above any solid foundation to ensure access to the bottom of the unit. To support units in an alternate steel support arrangement, consult your BAC Balticare Representative.

Units with and without Sound Attenuation

1. Unit Outline; 2. Air Intake; 3. Mounting holes Ø 22 mm; 4. Unit.

Dimensions (mm)

Model TXV

Max. Deflection (mm)

W

L

A

B

C

N° of 20 mm Anchor Bolts

109-154

8

2385

2775

2325

-

255

4

177-193

10

2385

3690

2325

-

255

4

217-333

10

2985

3690

2925

-

255

4

310-425

10

3610

3690

3550

-

255

4

354-500

12

2985

5520

2925

2440

270

8

Notes: 1. The recommended support arrangement for the units consists of parallel I-beams extending the full length of the unit. Supports and anchor bolts are to be designed and furnished by others. 2. All supporting beams are to be flush and level at top and must be oriented relative to gage line as shown. 3. Recommended design loads for each unit support beam should be 70% of the total unit operating weight applied as a uniform load to each of the unit beams. Beams should be designed in accordance with

standard structural practice. For the maximum allowable deflection of beams under the unit see table. 4. All mounting holes have a diameter of 22 mm at the locations shown. 5. If vibration isolators are used, a rail or channel must be provided between the unit (and optional attenuator) and the isolators to provide continuous unit support. Additionally the support beams must be designed to accommodate the overall length and mounting hole location of the isolators that may differ from those of the unit. Refer to vibration isolator drawings for these data.

Baltimore Aircoil

TXV - B 15

Engineering Specifications 1.0 Cooling Tower 1.1 General: Furnish and install _____ factory-assembled, induceddraft, axial fan, crossflow cooling tower(s) with single side air entry and vertical air discharge. Overall dimensions shall not exceed approximately _____ mm long x ______ mm wide x _____ mm high. The total connected fan kW shall not exceed _____ kW. The cooling tower(s) shall be Baltimore Aircoil Model ____________.

1.3 Corrosion Resistant Construction (standard): Unless otherwise noted in this specification, all steel panels and structural members shall be constructed of heavy-gauge Z600 metric hot-dip galvanised steel with all edges given a protective coating of zinc-rich compound and protected with the BALTIPLUS Corrosion Protection. (Alternate 1.3) Corrosion Resistant Construction (optional): Unless otherwise noted in this specification, all steel panels and structural members shall be protected with the BALTIBOND® Corrosion Protection System. The system shall consist of Z600 metric hot-dip galvanised steel prepared in a four-step (clean, pre-treat,

(Alternate 1.3) Type 304 or 316 Stainless Steel Construction: All steel panels and structural members, including the structural frame, hot and cold water basins, distribution covers and fan deck shall be constructed of Type 304 or 316 stainless steel and assembled with stainless steel nut and bolt fasteners. The fan cylinder shall be constructed of heavy-gauge Z600 metric hot-dip galvanised steel and protected with the BALTIBOND® Corrosion Protection System. 1.4 Quality Assurance: The cooling tower manufacturer shall have a Management System certified by an accredited registrar as complying with the requirements of ISO-9001:2000 to ensure consistent quality of products and services. 1.5 Warranty: The manufacturer’s standard equipment warranty shall be for a period of not less than one year from date of start-up or eighteen months from date of shipment, whichever occurs first.

2.0 Construction Details 2.1 Cold Water Basin: The cold water basin shall include a depressed section with drain/clean-out connection. The basin area under the wet deck surface shall be sloped toward the depressed section to facilitate cleaning. Standard basin accessories shall include a brass make-up valve with a large diameter plastic float for easy adjustment of operating water level. 2.2 Water Outlet: The cooling tower basin outlet shall be beveled. The outlet shall be provided with large area lift out strainers with

perforated openings sized smaller than the water distribution nozzles and an anti-vortexing device to prevent air entrainment. The strainer and vortex device shall be constructed of the same materials as the cold water basin to prevent dissimilar metal corrosion. 2.3 Water Distribution System: The distribution system shall be furnished with a single water inlet. The pipe stub connection shall be beveled for welding. Plastic metering devices shall be provided to ensure the uniform distribution of water over the wet deck surface.

3.0 Mechanical Equipment 3.1. Fan(s): Fan(s) shall be heavy-duty, axial flow with aluminum alloy blades selected to provide optimum cooling tower thermal performance with minimal sound levels. Air shall discharge through a fan cylinder designed for streamlined air entry and minimum tip clearance for maximum fan efficiency. The top of the fan cylinder shall be equipped with a conical, non-sagging removable fan guard. (Alternate 3.1) Fan(s): Fan(s) shall be of “Whisper Quiet” fan design for ultra low sound consisting of specially shaped aluminium blades with end caps and flexible hub connection. Air shall discharge through a fan cylinder designed for streamlined air entry and minimum tip clearance for maximum fan efficiency. The top of the fan cylinder shall be equipped with a conical, non-sagging removable fan guard. 3.2. Bearings: Fan(s) and shaft(s) shall be supported by heavy-duty, self-aligning, grease-packed ball bearings with moisture proof seals

and integral slinger collars, designed for a minimum L10 life of 40 000 hours (280 000 Hr. Avg. Life). 3.3. Fan Drive: The fan(s) shall be belt driven with taper lock sheaves. The belts shall be constructed of neoprene reinforced polyester cord and be specifically designed for cooling tower service. 3.4. Sheaves: Fan and motor sheave(s) shall be fabricated from corrosion-resistant materials to minimise maintenance and ensure maximum operating life. 3.5. Fan Motor: Fan motor(s) shall be totally enclosed fan cooled (TEFC), reversible, squirrel cage, ball bearing type designed specifically for cooling tower service. The motor shall be furnished with special moisture protection on windings, shafts and bearings.

4.0 BACross® Wet Deck Surface and Drift Eliminators 4.1. Wet Deck Surface and drift Eliminators: The wet deck surface and integral drift eliminators shall be impervious to rot, decay, and fungus or biological attack. The wet deck surface shall be

manufactured and performance tested by the cooling tower manufacturer to provide single source responsibility and assure control of the final product.

5.0 Combined Inlet Shields 5.1. Combined Inlet Shields: Combined inlet shields shall be separate from the wet deck surface and removable to allow easy access for inspection of the air/water interface at the air inlet side of the equipment. Combined inlet shields shall prevent UV-light and

debris from entering the unit, as well as prevent water splash out during fan cycling. They shall be constructed of maintenance free, corrosion and UV resistant material.

... because temperature matters

Open Cooling Towers

1.2 Thermal Capacity: The cooling tower(s) shall be warranted by the manufacturer to cool _____ l/s of water from ______ °C to _____°C at _____°C entering wet-bulb temperature.

rinse, dry) process with an electrostatically sprayed, thermosetting, hybrid polymer fuse-bonded to the substrate during a thermally activated curing stage and monitored by a 23-step quality assurance program.

TXV - B 16

6.0 Access 6.1. Plenum Access: Hinged access doors shall be provided on one or two sides of the tower for access into plenum section.

7.0 Sound 7.1 Sound Level: To maintain the quality of the local environment, the maximum sound pressure levels (dB) measured 15 m from the

TXV

Location

63

125

250

cooling tower operating at full fan speed shall not exceed the sound levels detailed below.

500

Discharge Air Inlet End Back

Baltimore Aircoil

1000

2000

4000

8000

dB(A)

FXT - B 45

FXT

Open Cooling Towers

Open Cooling Towers

Product Detail FXT Open Cooling Towers ..................................................................... B46 Benefits ..................................................................................................... B48 Construction Details ................................................................................ B49 Custom Features and Options ................................................................ B50 Accessories ............................................................................................... B51 Engineering Data ..................................................................................... B52 Structural Support .................................................................................. B54 Engineering Specifications ..................................................................... B56

FXT - B 46

FXT Open Cooling Towers Capacity Single Cell Capacity:

FXT

3 - 145 l/s

General Description FXT Cooling Towers deliver independently verified, fully rated thermal performance over a wide range of flow and temperature requirements. Standard design features satisfy today’s environmental concerns, minimize installation costs, maximize operating reliability, and simplify maintenance requirements.

Key Features z

Low energy consumption

z

Low installed cost

z

Easy maintenance

z

Long service life

z

Crossflow design

z

Forced draught configuration

z

Single side horizontal air entry

z

Horizontal air discharge

z

Aluminium axial fans

z

Gravity water distribution

Baltimore Aircoil

FXT - B 47

Open Cooling Towers

... because temperature matters

FXT - B 48

Benefits Low Installed Cost

FXT

z

All single cell FXT Cooling Towers ship completely assembled, minimizing installation time and cost: -

No motors to mount

-

No sheaves to align

-

No belts to install

-

No make-up system to assemble

Easy Maintenance z

z

This FXT unit is placed with one lift and ships fully assembled.

The interior of the unit is accessible through circular access doors for adjusting the float valve, cleaning the strainer or flushing the basin The fan motor is located on the exterior of the unit for easy maintenance and belt adjustment. On most models, a single threaded bolt and nut assembly further simplifies belt adjustment. Extended lubrication fittings are located on the exterior of the unit for bearing lubrication.

Circular Access Door

The Fan Motor is easily accessible at the base of the unit's exterior

Long Service Life z

Materials of Construction – Various materials are available to meet the corrosion resistance, unit operating life, and budgetary requirements of any project (See section Technical Resources, Materials of Construction" for more details)

Low Energy Consumption z

z

Evaporative cooling equipment minimizes the energy consumption of the entire system because it provides lower operating temperatures. The owner saves money while conserving natural resources and reducing environmental impact. The FXT provides the heat rejection required at the lowest possible energy input via: -

-

High efficiency, low kW axial fans High efficiency BACross® Wet Deck, which provides maximum air/water contact time at low air pressure drops Variable frequency drives

Baltimore Aircoil

FXT - B 49

Construction Details

z

Z600 hot-dip galvanized steel panels

2. Fan Drive System

z

Impervious to rot, decay and biological attack

z

Designed and manufactured by BAC

6. Air Inlet Cylinder

z

V-type belt drive

z

Heavy-duty bearings

z

Extended lubrication lines

z

Protection from moving parts

3. Low kW Axial Fan(s)

z

Easily removed for access to fans, bearings, motor and drives

z

Quiet operation

z

Corrosion resistant aluminum

z

Streamlines air entry for maximum efficiency

7. Inlet Screens

8. Water Make-Up Valve Assembly z

Bronze float valve

z

Large diameter plastic float

4. Water Distribution System z

Low pump head gravity distribution basin

z

Large orifice, non-clog nozzles

z

Steel distribution covers

9. Strainer z

Anti-vortexing design to prevent air entrainment

10. Access Door 5. BACross® Wet Deck Surface with Integral Drift Eliminators z

z

Circular access door

Plastic material

... because temperature matters

Open Cooling Towers

1. Heavy Duty Construction

FXT - B 50

Custom Features and Options Construction Options

FXT

z

z

Standard Construction: Steel panels and structural elements are constructed of heavy-gauge hot-dip galvanized steel protected with the Baltiplus Corrosion Protection on the outside of the cooling towers. Optional BALTIBOND® Corrosion Protection System: The BALTIBOND® Corrosion Protection System, a hybrid polymer coating used to extend equipment life, is applied to all hot-dip galvanized steel components of the cooling tower.

Note: See section Technical Resources, Material Options for more details on the materials described above.

Fan Drive System FXT cooling towers are belt-driven. The belts are easily adjusted by means of a threaded bolt and nut arrangement.

BACross® Wet Deck Surface An efficient wet deck surface designed, manufactured and tested by BAC is furnished as standard in all FXT cooling towers. It is impervious to rot, decay, biological attack. The special configuration with integral eliminators provides maximum air/water contact and low air pressure drop to ensure efficient heat transfer while minimizing power requirements.

Baltimore Aircoil

FXT - B 51

Accessories Basin Heaters

Model

Heaters -18 °C (kW)

FXT 27 - FXT 68

1x3

FXT 74 - FXT 86

1x4

FXT 97 - FXT 133

2x3

FXT 160 - FXT 250

2x4

FXT 194 - FXT 266

4x3

FXT 320 - FXT 500

4x4

Electric Water Level Control Package The electric water level control replaces the standard mechanical make-up valve when a more precise water level control is required. This package consists of a float switch mounted in the basin and a solenoid activated valve in the make-up water line. The valve is slow closing to minimize water hammer.

High Temperature Wet Deck If operation above 50°C is anticipated, an optional high temperature wet deck material is available which increases the maximum allowable entering water temperature to 55°C.

Air Discharge Screens Wire mesh screens are available to cover the discharge of the tower to prevent debris from entering the eliminators and cold water basin.

Distribution Basin Covers Removable covers for the hot water distribution basins will significantly reduce maintenance and cleaning requirements of the basins and nozzles. The covers will have either Baltiplus or Baltibond® Corrosion Protection System to match the equipment material specification.

Discharge Air Turning Vanes Discharge air turning vanes are available to direct the discharge air up and away from the unit. The turning vanes are installed at the factory on the discharge of the tower and require no increase in fan motor kW.

Distribution Basin Covers

Note: Discharge Air Turning Vanes are not compatible with Air Discharge Screens.

... because temperature matters

Open Cooling Towers

Units exposed to below freezing ambient temperatures require protection to prevent freezing of the water in the cold water basin when the unit is idle. Factory-installed heaters, which maintain the water temperature at 4°C, are a simple and inexpensive way of providing such protection. The heater package includes the heaters, a thermostat and a low level cut out switch to protect the heaters if the water level is too low. Standard electric heaters are selected for -18°C ambient temperature.

FXT - B 52

Engineering Data REMARK: Do not use for construction. Refer to factory certified dimensions & weights. This brochure includes data current at time of publication, which should be reconfirmed at the time of purchase. In the interest of product improvement, specifications, weights and dimensions are subject to change without notice. Up-to-date engineering data and more can be found at www.BaltimoreAircoil.com.

FXT

FXT 27 - FXT 500

1. Drain; 2. Water Outlet; 3. Overflow; 4. Make-Up; 5. Water Inlet; 6. Access Door ; 7. Top of Distribution Box; 8. Metering Orifices; 9. Flow Divider; *External Screen section only on FXT 211, 250, 422, 500.

Baltimore Aircoil

FXT - B 53

Operating Weight (kg)

Shipping Weight (kg)

Heaviest Section (kg)

Air Flow (m³/s)

Fan Motor (kW)

Fluid Inlet ND (mm)

Fluid Outlet ND (mm)

Make Up ND (mm)

H (mm)

L (mm)

W (mm)

FXT 27 FXT 32

945 950

425 430

425 430

4,85 5,32

(1) 0,75 (1) 1,1

100 100

100 100

15 15

1810 1810

1374 1374

2181 2181

FXT 43 FXT 51

1100 1110

455 465

455 465

7,08 8,11

(1) 1,5 (1) 2,2

150 150

150 150

15 15

2216 2216

1374 1374

2181 2181

FXT 60 FXT 68

1425 1430

555 560

555 560

9,93 11,76

(1) 2,2 (1) 4,0

150 150

150 150

15 15

2216 2216

1832 1832

2181 2181

FXT 74 FXT 88

1920 1925

780 785

780 785

11,03 13,07

(1) 2,2 (1) 4,0

200 200

200 200

25 25

2540 2540

1832 1832

2219 2219

FXT 97 FXT 116 FXT 133

2755 2765 2780

1000 1010 1025

1000 1010 1025

14,68 17,40 19,93

(1) 2,2 (1) 4,0 (1) 5,5

200 200 200

200 200 200

25 25 25

2540 2540 2540

2772 2772 2772

2219 2219 2219

FXT 160 FXT 173

3640 3655

1310 1325

1310 1325

24,10 26,53

(1) 5,5 (1) 7,5

200 200

200 200

25 25

2540 2540

3660 3660

2219 2219

FXT 211 FXT 250

4275 4295

1620 1640

1620 1640

30,22 34,60

(1) 7,5 (1) 11

200 200

200 200

25 25

3356 3356

3660 3660

2219 2219

FXT 194 FXT 232 FXT 266

5505 5525 5565

1995 2015 2055

1000 1010 1030

29,36 34,81 39,85

(2) 2,2 (2) 4,0 (2) 5,5

(2) 200 (2) 200 (2) 200

(2) 200 (2) 200 (2) 200

50 50 50

2540 2540 2540

5556 5556 5556

2219 2219 2219

FXT 320 FXT 346

7285 7320

2615 2650

1310 1325

48,19 53,04

(2) 5,5 (2) 7,5

(2) 200 (2) 200

(2) 200 (2) 200

50 50

2540 2540

7334 7334

2219 2219

FXT 422 FXT 500

8545 8590

3230 3275

1620 1640

60,44 69,19

(2) 7,5 (2) 11

(2) 200 (2) 200

(2) 200 (2) 200

50 50

3353 3353

7334 7334

2219 2219

General Notes 1. Unless otherwise indicated, all connections ND 100 and smaller are MPT and connections ND 125 and larger are beveled for welding. 2. Operating weight is for tower with water level in the cold water basin at overflow.

3. Unit height is indicate, for precise value refer to the certified print. 4. Inlet piping must rest on the flow divider. The inlet piping to the distribution box must be the correct size as indicated in the table.

... because temperature matters

Open Cooling Towers

Model FXT

FXT - B 54

Structural Support REMARK: Do not use for construction. Refer to factory certified dimensions & weights. This brochure includes data current at time of publication, which should be reconfirmed at the time of purchase. In the interest of product improvement, specifications, weights and dimensions are subject to change without notice. Up-to-date engineering data and more can be found at www.BaltimoreAircoil.com.

FXT

The recommended support arrangement for units consists of parallel I-beams running the full length of the unit, spaced as shown in the following drawing. Besides providing adequate support, the steel also serves to raise the unit above any solid foundation to ensure access to the bottom of the unit. To support units in an alternate steel support arrangement, consult your BAC Balticare Representative. 1. Supporting steelwork and anchor bolts are to be selected and installed by others. 2. All supporting steel must be flush and level at the top and must be oriented to the gage line as shown in SECTION A-A. 3. Recommended design loads for each beam should be 65% of the total operating weight applied as a uniform load to each beam. Beam should be designed in accordance with standard design practice. Refer to the below table for the maximum allowable deflection of beams

4. All mounting holes are 16 mm diameter at the locations shown. 5. If continuous vibration isolator rails are used, be certain to allow for the length of the rails when determining length of supporting steel. Vibration isolator rails are sometimes longer than the cooling tower dimensions shown. Refer to vibration isolator drawings for this information. If point vibration isolation is used, the isolators should be installed at the mounting hole locations shown.

Single Cell

Recommended Support

Alternate Support 1. Holes; 2. Outline of Tower; 3. Support Beams (by others); 4. Air Inlet Side.

Baltimore Aircoil

FXT - B 55

Double Cell

Model FXT

A (mm)

B (mm)

C (mm)

P1 (kg)

P2 (kg)

Maximum Deflection (mm)

FXT 27 FXT 32

1549 1549

1067 1067

-

284 285

189 190

13 13

FXT 43 FXT 51

1549 1549

1067 1067

-

330 333

220 222

13 13

FXT 60 FXT 68

1549 1549

1524 1524

-

449 450

264 265

13 13

FXT 74 FXT 88

1549 1549

1524 1524

-

528 529

432 433

13 13

FXT 97 FXT 116 FXT 133

2181 2181 2181

2438 2438 2438

-

758 760 765

620 622 626

13 13 13

FXT 160 FXT 173

2181 2181

3353 3353

-

1001 1005

819 822

13 13

FXT 211 FXT 250

2181 2181

3353 3353

-

1154 1160

983 988

13 13

FXT 194 FXT 232 FXT 266

2181 2181 2181

2438 2438 2438

346 346 346

758 760 765

619 622 626

13 13 13

FXT 320 FXT 346

2181 2181

3353 3353

321 321

1001 1007

820 823

13 13

FXT 422 FXT 500

2181 2181

3353 3353

321 321

1154 1160

983 988

13 13

... because temperature matters

Open Cooling Towers

1. Holes; 2. Outline of Tower; 3. Support Beams (by others); 4. Air Inlet Side

FXT - B 56

Engineering Specifications

FXT

1.0 Cooling Tower 1.1 General: Furnish and install _____ factory-assembled, forceddraft, axial fan, crossflow cooling tower(s). The tower(s) shall have air entry on one side only. The tower(s) shall have the fan and all moving parts located in the dry entering airstream provide greater reliability and long life. Overall dimensions shall not exceed approximately _____ mm long x ______ mm wide x _____ mm high. The total connected fan kW shall not exceed _____ kW. The cooling tower(s) shall be Baltimore Aircoil Model ____________.

(Alternate 1.3) Corrosion Resistant Construction (optional): Unless otherwise noted in this specification, all steel panels and structural members shall be protected with the BALTIBOND® Corrosion Protection System. The system shall consist of Z600 metric hot-dip galvanized steel prepared in a four-step (clean, pre-treat, rinse, dry) process with an electrostatically sprayed, thermosetting, hybrid polymer fuse-bonded to the substrate during a thermally activated curing stage and monitored by a 23-step quality assurance program.

1.2 Thermal Capacity: The cooling tower(s) shall be warranted by the manufacturer to cool _____ l/s of water from ______ °C to _____C at _____°C entering wet-bulb temperature.

1.4 Quality Assurance: The cooling tower manufacturer shall have a Management System certified by an accredited registrar as complying with the requirements of ISO-9001:2000 to ensure consistent quality of products and services.

1.3 Corrosion Resistant Construction (standard): Unless otherwise noted in this specification, all steel panels and structural members shall be constructed of heavy-gauge Z600 metric hot-dip galvanized steel with all edges given a protective coating of zinc-rich compound and the exterior protected with the BALTIPLUS Corrosion Protection.

1.5 Warranty: The manufacturer’s standard equipment warranty shall be for a period of not less than one year from date of startup or eighteen months from date of shipment, whichever occurs first.

2.0 Construction Details 2.1. Cold Water Basin: The cold water basin shall be constructed of heavy-gauge Z600 hot-dip galvanized steel. Standard accessories shall include circular access doors, large-area, lift-out hot-dip galvanized steel strainers with perforated openings sized smaller than water distribution nozzle orifices, an integral anti-vortexing hood to prevent air entrainment, and a brass make-up valve with large diameter plastic float, arranged for easy adjustment.

2.3. Water Distribution System: Hot water distribution basin shall be open gravity type and constructed of heavy-gauge, Z600 hot-dip galvanized steel. Basin weirs and plastic metering orifices shall be provided to assure even distribution of water over the wet deck surface. Lift-off distribution cover shall be constructed of heavygauge, Z600 hot-dip galvanized steel.

3.0 Mechanical Equipment 3.1. Fan(s): Fan(s) shall be heavy-duty, axial flow type. Air shall be drawn into the tower through a fan cylinder designed for streamlined air entry and minimum fan blade tip clearance for maximum fan efficiency. 3.2. Bearings: Fan(s) shall be mounted on a horizontal solid steel shaft supported by two heavy-duty, self-aligning, relubricatable ball bearings with cast iron housings and designed for minimum L10 life of 40 000 hours (280 000 Hr. Avg. Life). Extended lubrication lines are provided for ease of maintenance.

3.3. Fan Drive: Fan(s) shall be driven by V-belts and all moving parts shall be protected by removable steel screens that shall ship installed on the unit. 3.4. Fan Motor(s): Fan motor(s) shall be totally enclosed fan cooled (TEFC), reversible, squirrel cage, ball bearing type, designed specifically for cooling tower service. The motor shall be furnished with special moisture protection on windings, shafts and bearings.

4.0 BACross® Wet Deck Surface and Drift Eliminators 4.1. Wet Deck Surface and drift Eliminators: The wet deck surface and integral drift eliminators shall be impervious to rot, decay, and fungus or biological attack. The wet deck surface shall be

manufactured and performance tested by the cooling tower manufacturer to provide single source responsibility and assure control of the final product.

5.0 Access 5.1 Basin Access: Circular access doors shall be provided for easy access to the make-up water assembly and suction strainer for routine maintenance.

6.0 Sound 6.1 Sound Level: To maintain the quality of the local environment, the maximum sound pressure levels (dB) measured 15 m from the

Location

63

125

250

cooling tower operating at full fan speed shall not exceed the sound levels detailed below.

500

Discharge Air Inlet End Top

Baltimore Aircoil

1000

2000

4000

8000

dB(A)

RCT - B 1

RCT

Open Cooling Towers

Open Cooling Towers

.

Product Detail RCT Open Cooling Tower ........................................................................ B2 Benefits ....................................................................................................... B4 Construction Details .................................................................................. B8 Custom Features and Options ................................................................ B10 Accessories ................................................................................................ B11 Engineering Data ..................................................................................... B12 Structural Support .................................................................................. B16 Engineering Specifications ..................................................................... B19

RCT - B 2

RCT Open Cooling Tower Capacity Single Cell Capacity:

RCT

40 – 145 l/s

General Discription Commercial applications demand reliable, cost effective and energy efficient solutions. With an ever increasing focus on operational reliability and ease of maintenance. It is paramount that cooling equipment be also easy to inspect, clean & maintain. The RCT cooling tower responds to all these requirements thanks to built-in design features. Industrial applications face unique challenges in their processes with varying site conditions. The RCT cooling tower provides solutions to these challenges by reducing the cost of plant design, construction, operation and on-going maintenance, whilst improving the standard of quality and construction, required by medium to heavy industry.

Key Features z

Total Lower Installation Costs

z

Low Noise

z

Low Height

z

Superior Pultruded Composite Construction

z

Superior Maintenance and Cleaning Possibilities

Baltimore Aircoil

RCT - B 3

Open Cooling Towers

... because temperature matters

RCT - B 4

Benefits

RCT

Total Lower Installation Costs

Modular Design

Factory Assembled

Single or multiplexed configurations, common or segmented basins, partitioned or extended air inlets and increased capacity control steps, all are but a few examples of the flexible modular cooling tower design. The tower can be shipped directly from the factory as a fully assembled unit, as unit modules or knocked down, to suit diverse and often restricted on-site conditions. The low shipping weights and modular shipping options reduce transport and crane costs. Lifting lugs, provided as standard, offer secure fixing points for safe crane lifts. Lower installation costs are achieved due to flanged inlet-outlet connections, solvent welded drain connections and threaded make-up, overflow and quick-fill connections.

Total Lower Installation Cost

Low Noise The use of high efficiency axial fans as standard, a smooth faced streamlined air entry fan cylinder and a minimum tip clearance, all translate into a low air inlet velocity which in turn ensures noise levels are minimised. Varying fan powers can also be achieved within a nominal tower size.

Low Noise Axial Fan

Baltimore Aircoil

RCT - B 5

Low Height The tower has been designed as a low height counter-flow cooling tower able to accommodate height sensitive sites, reduce pump head and provide easy access to all of its components.

Superior Pultruded Composite Construction The use of high strength Pultruded Composite components for primary structure and cladding, offers many advantages over conventional hand laid or chopped strand fibreglass construction methods. Pultruded composites possess a superior strength to weight ratio of up to five times that of chopped strand fibreglass.

Superior Maintenance and Cleaning Possibilities z

Access to complete unit interior - The large access panel is fitted with easily removable knobs. Removing the access panel does not require any tools or dismantling of the tower structure, providing unequalled access to all of the internal cooling tower components for inspection, cleaning and maintenance.

Large Access Door

z

Easy Access to Basin

Basin Accessible from all Sides - Removal of the louvers, requiring no tools, provides access to all sides of the smooth faced cold water basin for inspection, cleaning and maintenance.

... because temperature matters

Open Cooling Towers

Strenght Pultruded Composite

Low Height

RCT - B 6

RCT

z

Easy Access to Float Valve - Access to and adjustment of the float valve is simplified. The stainless steel suction strainer can easily be inspected, removed and cleaned inside.

Easy Access to Float Valve

z

z

Removable Fill - The fill medium can easily be removed for cleaning thanks in part to the ample accessibility, gained by removal of the access panel, and to the easy to handle removable fill blocks. Removable Spray System - Cleaning and inspection of the spray system can be performed in situ or by removing the spray branch arms. No tools are required for the removal of the branch arms or the individual water distribution nozzles.

Removable Spray system

z

Removable Fill

Removable Eliminators

Removable Eliminators - Removal of high efficiency drift eliminators can be accomplished easily without the removal of other internal components or by having to dismantle the tower structure. The eliminators rest on supports specifically designed to this purpose.

Baltimore Aircoil

RCT - B 7

z

Motor Outside Airstream - Units larger than model 2142 include an adjustable motor base plate for belt tensioning, extended lubrication lines with externally mounted grease nipples are provided, as standard to ease of scheduled maintenance. Smaller units are supplied as direct drive units.

z

Easy Access to Drives

Easy Access to Drives - Removal of the fan screen for access to belts and drives is not required. These drive components are easily accessible through the specially designed belt guard for inspection adjustment or replacement purposes.

... because temperature matters

Open Cooling Towers

Motor Outside Airstream

RCT - B 8

RCT

Construction Details

1. Fan z

Aluminium Axial Fans

z

Small tip clearance tolerance

z

Low air inlet velocity

z

Minimum Noise

2. Drive Train z

Easy access to drives and belts for inspection and adjustment.

z

Stainless steel shaft.

z

Corrosion resistant cast aluminium sheaves

z

Heavy-duty bearings

3. Motor z

Models RCT-2118 and 2129 utilise direct drive motor.

z

Larger units have the fan motor outside of the moist discharge air stream and use belt drives.

z

Belts provide reliability and long service life with low maintenance requirements

Baltimore Aircoil

RCT - B 9

4. Drift Eliminators z

UV resistant non-corrosive material, impervious to rot, decay and biological attack

z

Three distinct changes in air direction to reduce drift loss significantly

z

Assembled in easy to handle sections, which can be removed for access to the equipment interior

5. Access Door (not shown)

z

The larger access door is easily removable to provide complete access to drift eliminators, spray system and fill Larger units are equipped with anchor points to secure door when removed

6. Fill z

The fill is impervious to rot, decay and resistant to fungus or biological attacks

z

It consists of high efficiency cross-fluted sheets, solvent welded into lightweight blocks

z

Blocks are sized for easy handling and removal for cleaning.

7. Water Distribution System z

Low pressure, stationery type nozzles

z

Heavy duty PVC spray branches are grommeted to facilitate removal and cleaning

8. Cold Water Basin z

z

The cold water basin is made of fibreglass reinforced polyester (FRP) and extra reinforced in critical areas. Sloped basin sides with smooth internal finish for easy cleaning.

9. Strainer z

Stainless steel construction, anti-vortex design.

10. Make-up Assembly z

Adjustable water make-up assembly, over flow and quick fill connections are supplied standard.

11. Connections z

Flanged inlet and outlet connections

z

Threaded make-up, overflow and quick fill connections

12. Combined Inlet Shields z

Removal of the combined inlet shields provides access to all sides of the cold water basin for inspection, cleaning and maintenance.

13. Roofdeck z

Smooth faced air entry fan cylinders

z

Close manufacturing tolerances allow small tip clearance providing an increased efficiency.

... because temperature matters

Open Cooling Towers

z

RCT - B 10

Custom Features and Options Construction Options

Standard construction: High strenght pultruded composite components for the primary structure combined with patented bonded panel to post connection.

RCT

Fan Drive System

High efficiency fans with direct drive motors for models RCT-2118 and RCT-2129. Larger models are belt driven. All belt driven units have extended lubrication lines to the edge of the fan cylinder. The mechanical equipment support and fan guard are made of hot dip galvanised steel. Optional: Mechanical equipment support assembly in SST 304.

Cold Water Basin

The RCT tower cold water basin is constructed of high performance fibreglass reinforced polyester. The suction connection is flanged. Optional: Units can be supplied without cold water basin for field assembly on a concrete tank. A unit supplied without cold water basin excludes basin, suction strainer, drain and make-up assembly. Triple fan units are always supplied without cold water basin.

Factory Assembled

The RCT Tower is completely factory-assembled. Optional: The tower can be shipped in knocked-down version for assembly on site. This enables overseas transport in containers and significantly reduces transport cost.

Heat Transfer Surface Alternatives z

z

z

Standard Heat Transfer Surface: The filmtype heat transfer surface supplied as standard with the cooling towers has been carefully selected for industrial applications. The 19 mm spacing between the surface sheets gives excellent air/water contact with low air pressure loss. The standard heat transfer surface provides high thermal efficiency and is sufficient to avoid clogging in most environments. Optional Film-Type Space 12 mm: For applications where the cooling tower water is clean, alternative models with 12 mm fill are available.

Telescopic fill supports (only for heavy duty 26 mm Fill Type)

Heavy Duty 26 mm Fill Type: Heavier contamination, which results in a heavy accumulation on the heat transfer surface, requires a higher structural strength than can be accomplished with film-type. For such situations, a heat transfer surface is available, constructed of heavy-duty wave formed FRP panels spaced 26 mm apart. With the unique integrated telescopic fill supports, the FRP fill panels can easily be removed for cleaning.

Combined Inlet Shields Combined Inlet shields prevent biological growth from sunlight, act as a filter for air borne impurities and debris and eliminate water splash out.

Baltimore Aircoil

RCT - B 11

Accessories Two-Speed Fan Motor An effective method of adding steps of capacity control and saving energy is the installation of twospeed fan motors in lieu of the standard single-speed motors. Two-speed motors are ideally suited for this purpose. At half fan speed the equipment capacity is still about 60% of design whereas the drawn fan power is only about 20% of the full speed motor power. In addition, at low speed, sound levels will generally reduce by about 9 dB(A).

The electric water level control replaces the standard mechanical make-up valve when a more precise water level control is required. This package consists of a float switch mounted in the basin and a solenoid activated valve in the make-up water line. The valve is slow closing to minimize water hammer.

Vibration Cut-out Switch A factory-mounted vibration cut-out switch is available to effectively protect against equipment failure due to excessive vibration of the mechanical equipment system. BAC can provide a vibration cut-out switch in an IP65 enclosure to ensure reliable protection.

Basin Heaters Units exposed to below freezing ambient temperatures require protection to prevent freezing of the water in the cold water basin when the unit is idle. Factory-installed heaters, which maintain the water temperature at 4°C, are a simple and inexpensive way of providing such protection. The heater package includes the heaters, a thermostat and a low level cut out switch to protect the heaters if the water level is too low. Standard electric heaters are selected for -18°C ambient temperature. Heater -18°C (kW)

Model No. RCT Single Fan Units

Double Fan Units

RCT-2118 / RCT 2129

1x5

2x5

RCT-2142 / RCT-2156

1x6

2x6

RCT-2183 / RCT-2208

1x6

2x6

RCT-2238 / RCT2262

2x4

4x4

RCT-2299 / RCT-2320

2x5

4x5

RCT-2368 / RCT-2386

2x6

N.A.

RCT-2418 / RCT-2441

2x6

N.A.

Equalising Connection Whenever cooling towers are installed to operate in parallel, the water level in the basins should be equalised by means of an equalising connection. The equalising connection can be either a whole pattern cut out only or a connection to the basin.

Basin Sweeper Piping Basin sweeper piping provides an effective method of preventing sediment from collecting in the cold water basin of the unit. A complete piping system, including nozzles, is provided in the unit basin for connection to side stream filtration equipment. Note: For more information, please refer to the section "Technical Resources, Filtration".

... because temperature matters

Open Cooling Towers

Electric Water Level Control Package

RCT - B 12

Engineering Data REMARK: Do not use for construction. Refer to factory certified dimensions & weights. This brochure includes data current at time of publication, which should be reconfirmed at the time of purchase. In the interest of product improvement, specifications, weights and dimensions are subject to change without notice. Up-to-date engineering data and more can be found at www.BaltimoreAircoil.com.

RCT

Single Fan Units - Square Box Sizes

1. Water Inlet; 2. Water Outlet; 3. Drain; 4. Overflow; 5. Make-Up; 6. Quick Fill; 7. Fan Motor.

Model

Shipping Operating Fan Air Weight Weight Motor Flow (kg) (kg) (kW) (m3/s)

Inlet ND (mm)

Outlet ND (mm)

Drain ND (mm)

Overflow Quick-fill ND ND (mm) (mm)

Makeup ND (mm)

H

H1

L

W

(mm)

(mm)

(mm)

(mm)

RCT-2118-1 RCT-2129-1

1000 1000

2675 2675

5,5 7,5

15,4 17,3

150 150

150 150

50 50

50 50

20 20

20 20

3310 3310

N/A N/A

2284 2284

2284 2284

RCT-2142-1 RCT-2156-1

1250 1250

3375 3375

5,5 7,5

18,5 20,4

150 150

200 200

50 50

80 80

20 20

20 20

3407 3407

2535 2535

2588 2588

2588 2588

RCT-2183-1 RCT-2208-1

1550 1550

4125 4125

7,5 11

23,9 27,2

200 200

200 200

50 50

80 80

20 20

20 20

3427 3427

2555 2555

2893 2893

2893 2893

RCT-2238-1 RCT-2262-1

1800 1800

4850 4850

11 15

31,2 34,2

200 200

200 200

50 50

80 80

40 40

40 40

3728 3728

2735 2735

3198 3198

3198 3198

RCT-2299-1 RCT-2320-1

2100 2100

5700 5700

15 18,5

39,0 41,8

200 200

250 250

50 50

80 80

40 40

40 40

3890 3890

2735 2735

3500 3500

3500 3500

Remarks: 1. Access door is always opposite to inlet connection end.

4. Actual outlet sized to match flow.

2. Alternative inlet/outlet and tower configurations are available.

5. Models RCT-2118-1 and RCT-2129-1 have direct drive motors.

3. Nominal outlet connection size provided.

6. Add 70 mm to H1 for shipping height of the upper section. The height of the lower section should be increased by 270 mm.

Baltimore Aircoil

RCT - B 13

Single Fan Units - Rectangular Box Sizes

Model

Shipping Operating Fan Air Weight Weight Motor Flow (kg) (kg) (kW) (m3/s)

Inlet ND (mm)

Outlet ND (mm)

Drain ND (mm)

Overflow ND (mm)

Makeup ND (mm)

Quick-fill H ND (mm) (mm)

H1

L

W

(mm)

(mm)

(mm)

RCT-2368-1 RCT-2386-1

2700 2700

7300 7300

18,5 22

47,8 50,2

200 200

200 200

50 50

80 80

40 40

40 40

4298 4298

3195 3195

4787 4787

3198 3198

RCT-2418-1 RCT-2441-1

3000 3000

8500 8500

18,5 22

54,3 57,3

200 200

250 250

50 50

80 80

40 40

40 40

4503 4503

3195 3195

5247 5247

3500 3500

Remarks: 1. Access door is always opposite to inlet connection end.

4. Actual outlet sized to match flow.

2. Alternative inlet/outlet and tower configurations are available.

5. Add 70 mm to H1 for shipping height of the upper section. The height of the lower section should be increased by 270 mm.

3. Nominal outlet connection size provided.

... because temperature matters

Open Cooling Towers

1. Water Inlet; 2. Water Outlet; 3. Drain; 4. Overflow; 5. Make-Up; 6. Quick Fill; 7. Fan Motor.

RCT - B 14

RCT

Double Fan Units

1. Water Inlet; 2. Water Outlet; 3. Drain; 4. Overflow; 5. Make-Up; 6. Quick Fill; 7. Fan Motor.

Model

Shipping Operating Weight Weight (kg) (kg)

Fan Motor (kW)

Air Flow (m3/s)

Inlet ND (mm)

Outlet ND (mm)

Drain ND (mm)

Overflow ND (mm)

Makeup ND (mm)

Quick-fill H H1 L W ND (mm) (mm) (mm) (mm) (mm)

RCT-2118-2 RCT-2129-2

2000 2000

5400 5400

(2x) 5,5 (2x) 7,5

30,8 34,6

(2x) 150 (2x) 150

150 150

(2x) 50 (2x) 50

(2x) 50 (2x) 50

40 40

40 40

3380 3380

N/A N/A

4548 4548

2284 2284

RCT-2142-2 RCT-2156-2

2500 2500

6800 6800

(2x) 5,5 (2x) 7,5

37,1 40,8

(2x) 150 (2x) 150

200 200

(2x) 50 (2x) 50

(2x) 80 (2x) 80

40 40

40 40

3555 3555

2535 2535

5157 5157

2588 2588

RCT-2183-2 RCT-2208-2

3100 3100

8300 8300

(2x) 7,5 (2x) 11

47,8 54,4

(2x) 200 (2x) 200

200 200

(2x) 50 (2x) 50

(2x) 80 (2x) 80

40 40

40 40

3653 3653

2555 2555

5769 5769

2893 2893

RCT-2238-2 RCT-2262-2

3600 3600

9750 9750

(2x) 11 (2x) 15

62,4 68,4

(2x) 200 (2x) 200

200 200

(2x) 50 (2x) 50

(2x) 80 (2x) 80

40 40

40 40

3915 3915

2735 2735

6377 6377

3198 3198

RCT-2299-2 RCT-2320-2

4200 4200

11450 11450

(2x) 15 (2x) 18,5

78,1 83,5

(2x) 200 (2x) 200

250 250

(2x) 50 (2x) 50

(2x) 80 (2x) 80

40 40

40 40

4096 4096

2735 2735

6982 6982

3499 3499

Remarks: 1. Access door is always opposite to inlet connection end.

4. Actual outlet sized to match the flow.

2. Alternative inlet/outlet and tower configurations are available.

5. Models RCT-2118-2 and RCT-2129-2 have direct drive motors.

3. Nominal outlet connection size provided.

6. Add 70 mm to H1 for shipping height of the upper section. The height of the lower section should be increased by 270 mm.

Baltimore Aircoil

RCT - B 15

Triple Fan Units

Shipping Weight (kg)

Operating Weight (kg)

Fan Motor (kW)

Air Flow (m3/s)

Inlet ND (mm)

H

H1

L

W

(mm)

(mm)

(mm)

(mm)

RCT-2142-3 RCT-2156-3

3700 3700

10200 10200

(3x) 5,5 (3x) 7,5

55,6 61,2

(3x) 150 (3x) 150

3318 3318

2535 2535

7731 7731

2588 2588

RCT-2183-3 RCT-2208-3

4700 4700

12400 12400

(3x) 7,5 (3x) 11

71,6 81,6

(3x) 200 (3x) 200

3427 3427

2555 2555

8646 8646

2893 2893

RCT-2238-3 RCT-2262-3

5400 5400

14700 14700

(3x) 11 (3x) 15

93,6 102,6

(3x) 200 (3x) 200

3695 3695

2735 2735

9556 9556

3198 3198

RCT-2299-3 RCT-2320-3

6300 6300

17100 17100

(3x) 15 (3x) 18,5

117,1 125,3

(3x) 200 (3x) 200

3780 3780

2735 2735

10465 10465

3499 3499

Model

Remarks: 1. Access door is always opposite to inlet connection end.

4. Models RCT-2118-3 and RCT-2129-3 have direct drive motors.

2. Alternative water inlet and tower configurations are available.

5. Add 70 mm to H1 for shipping height of the upper section. The lower section is shipped knocked down.

3. Triple fan units are not available with common FRP Basin. Only for installation on concrete basin.

... because temperature matters

Open Cooling Towers

1. Water Inlet; 2. Fan Motor; 3. Concrete Basin (by others).

RCT - B 16

Structural Support The recommended support arrangement for units consists of parallel I-beams running the full length of the unit, spaced as shown in the following drawing. Besides providing adequate support, the steel also serves to raise the unit above any solid foundation to ensure access to the bottom of the unit. To support units in an alternate steel support arrangement, consult your BAC Balticare Representative.

RCT

Single Fan - Square Box Sizes

1. Outline of Unit; 2. Mounting holes; 3. FRP Cold Water Basin; 4. Water Inlet Side.

Single Fan - Rectangular Box Sizes

1. Outline of Unit; 2. Mounting holes; 3. FRP Cold Water Basin; 4. Water Inlet Side.

Baltimore Aircoil

RCT - B 17

MINIMUM SUPPORT REQUIREMENTS RCT

DIMENSIONS (mm) MAX. DEFLECTION (mm) A

B

C

2198

N/A

2

RCT 2142-1 RCT 2156-1

2502

N/A

2

RCT 2183-1 RCT 2208-1

2806

N/A

2

RCT 2238-1 RCT 2262-1

3112

N/A

3

RCT 2299-1 RCT 2320-1

3416

N/A

3

RCT 2368-1 RCT 2386-1

3112

1594

1346

3

RCT 2418-1 RCT 2441-1

3416

1748

1638

3

N/A = Not Applicable

Double Fan Units

1. Outline of Unit; 2. Mounting holes; 3. FRP Cold Water Basin; 4. Water Inlet Side. MINIMUM SUPPORT REQUIREMENTS RCT

DIMENSIONS (mm) MAX. DEFLECTION (mm) A

RCT 2118-2 RCT 2129-2

2198

4

RCT 2142-2 RCT 2156-2

2502

5

RCT 2183-2 RCT 2208-2

2806

5

RCT 2238-2 RCT 2262-2

3112

6

RCT 2299-2 RCT 2320-2

3416

6

... because temperature matters

Open Cooling Towers

RCT 2118-1 RCT 2129-1

RCT - B 18

RCT

Triple Fan Units - Concrete Sump

1. Outline of Unit; 2. Water Inlet Side.

MINIMUM SUPPORT REQUIREMENTS RCT

DIMENSIONS (mm) MAX. DEFLECTION (mm) A

B

C

RCT 2142-3 RCT 2156-3

2222

7742

2592

7

RCT 2183-3 RCT 2208-3

2526

8654

2896

8

RCT 2238-3 RCT 2262-3

2832

9572

3202

9

RCT 2299-3 RCT 2320-3

3136

10486

3506

10

Notes: 1. Support beams should be sized in accordance with accepted structural practice. Maximum deflection of beam under the unit to be 1mm/m unit length. Beams can be selected for 65% of the operating weight as a uniform load under each of the two exterior beams. The centre beam underneath the sloping sump should not take any of the unit weight as it is merely there to prevent excessive sump bottom deflection.

2. Supporting steel work and anchor bolts are to be selected and furnished by others. 3. All supporting steel must be flush and level at the top. 4. If vibration isolator rails are used between tower and supporting steel, the supporting steel length should meet vibration rail length. If point isolators are used, they should be mounted under the supporting steel.

REMARK: Do not use for construction. Refer to factory certified dimensions & weights. This brochure includes data current at time of publication, which should be reconfirmed at the time of purchase. In the interest of product improvement, specifications, weights and dimensions are subject to change without notice. Up-to-date engineering data and more can be found at www.BaltimoreAircoil.com.

Baltimore Aircoil

RCT - B 19

Engineering Specifications 1.0 Cooling Tower 1.1 General: Supply and install factory assembled cooling tower of counter-flow, induced draft, axial fan design. Each cooling tower shall be guaranteed by the manufacturer to cool ___ litres per second of

water from ___ °C (HW) entering water temperature to ___ °C (CW) leaving water temperature at ___ °C (WB) entering wet bulb temperature.

2.0 Construction Details to the cooling tower interior. Louvers shall be easily removable lightweight sections providing easy access for cleaning. 304-grade stainless steel deflector shall be factory fitted at the bottom of and inside the louvers to direct water away from the louver, preventing splash out. 2.5 Wet Deck Surface: The film type fill shall be impervious to rot, decay and fungus or biological attacks. It shall consist of high efficiency cross-fluted sheets solvent welded into lightweight blocks sized for easy handling and removal for cleaning. 2.6 Water Distribution System: Water shall be distributed evenly over the wet deck surface by a low pressure, stationery, non rotating type water distribution system incorporating heavy duty PVC spray branches and plastic spray nozzles held into place with snap rubber grommets. 2.7 Strainer: The cold water basin strainer shall be a 304-grade stainless steel cylindrical type having a solid top cover plate with a perforated mesh bottom of sufficient open area relative to the suction flow rate and by design, prevent vortexing at the outlet. 2.8 Hardware: All wetted hardware shall be 304-grade stainless steel.

3.0 Mechanical Equipment 3.1 Fan: The adjustable pitch axial flow fan(s) shall be of low noise, multi-bladed type heavy duty extruded aluminium. The fan shall operate within a FRP fan cylinder having an even and regular smooth faced internal finish ensuring a streamlined air entry and minimum tip clearance for maximum fan efficiency. 3.2 Motor: The fan motor(s) shall be to IP55 standard with Class F insulation specifically designed for cooling tower service. The fan motor shall be fully outside of the moist discharge air stream for belt driven units. The motor shall be located adjacent to the fan cylinder for ease of access for maintenance and increased motor life expectancy. The motor is to be located below the top of the cooling tower ensuring overall tower height is kept to a minimum and external of discharge ducting in such applications.

3.3 Mechanical Support: The mechanical support shall be of HDG steel construction. The entire mechanical arrangement shall simply bolt to the top of the fan cylinder for ease of access for maintenance. The fan shaft shall be of 304 stainless steel supported by heavy duty, self aligning, grease packed ball bearings specifically suited to vertical shaft application with moisture proof seals and integral slingers. Extended lubrication lines shall be provided as standard to the bearings with grease nipples located outside for ease of scheduled maintenance. 3.4 Belt Drive: Units with belt drive shall be via standard V belts for ease of availability. The motor pulley shall be located outside of the discharge air stream. The entire drive arrangement is to be protected by a hinged cover guard in HDG.

4.0 Drift Eliminators 4.1 Drift Eliminators: The plastic drift eliminators shall be UV resistant and impervious to rot, decay and fungus or biological

attacks. They shall consist of high efficiency three pass wave formed blades solvent welded into lightweight, easily removable sections.

5.0 Combined Inlet Shields 5.1. Combined Inlet Shields: Combined inlet shields shall be separate from the wet deck surface and removable to allow easy access for inspection of the air/water interface at the air inlet side of the equipment. Combined inlet shields shall prevent UV-light and

debris from entering the unit, as well as prevent water splash out during fan cycling. They shall be constructed of maintenance free, corrosion and UV resistant material.

6.0 Access 6.1 Access: One full side of the casing shall be removable to provide full and open access to all internal tower components for inspection, maintenance and cleaning. The access panel shall be retained by

easily removable knobs, not requiring dismantling of the tower structure.

... because temperature matters

Open Cooling Towers

2.1 Structure: The cooling tower structure and casing shall be constructed of high strength Pultruded Composite materials. All pultruded composite components shall be moulded to exacting standards with UV resistant polyester resins such that UV protection is afforded throughout the entire embodiment of the components as well as being an externally applied coating. 2.2. Internal Surfaces: All internal surfaces of the casing, basin, roof deck and fan cylinder shall have an even and regular smooth faced finish resulting from either an open moulding or pultruded moulding process where the faces of these components come into direct contact with the mould to facilitate easy cleaning. Internal flow coated surfaces that have not come in contact with the mould shall not be acceptable. 2.3 Cold Water Basin: The basin shall be constructed of high performance Fibreglass Reinforced Polyester (FRP) and reinforced in critical areas. The basin shall have a smooth internal finish and slope to a center drain for ease of cleaning. All suction, drain, overflow and quick fill connections shall be furnished as standard. The suction connection shall be flanged. Easy and complete access shall be made possible from all sides. 2.4 Air Inlet Louvers: Air Inlet Louvers shall be plastic material, designed to prevent splash out and minimise the passage of sunlight

RCT - B 20

7.0 Sound 7.1 Sound Level: To maintain the quality of the local environment, the maximum sound pressure levels (dB) measured 15 m from the Location

63

125

250

cooling tower operating at full fan speed shall not exceed the sound levels detailed below.

500

Discharge Air Inlet End

RCT

Back

Baltimore Aircoil

1000

2000

4000

8000

dB(A)

IMT - B 1

IMT

Open Cooling Towers

Open Cooling Towers

Product Detail IMT Open Cooling Towers ....................................................................... B2 Benefits ....................................................................................................... B4 Construction Details .................................................................................. B6 Custom Features and Options .................................................................. B8 Accessories ............................................................................................... B10 Engineering Data ...................................................................................... B11 Structural Support .................................................................................. B14 Engineering Specifications ..................................................................... B19

IMT - B 2

IMT Open Cooling Towers Capacity single cell capacity

IMT

35 – 575 l/s

General Description The features of modular design are incorporated in all IMT cooling towers to significantly reduce site assembly time and cost. IMT cooling towers are designed to meet the demanding conditions of a harsh industrial environment. Highly corrosion resistant materials are available to insure long life under these conditions. Structural strength is provided by heavy duty structural angles of stainless steel, hot dip galvanized steel or galvanized steel protected by the Baltibond Corrosion protection system. Standard cladding and fan stack materials are Fiberglass Reinforced Polyester (FRP)

Key Features z

Sharply reduced Site assembly cost

z

Superior durability through industrial quality materials

z

Assured thermal performance

z

Versatility in selection to suit every project requirement

Baltimore Aircoil

IMT - B 3

Open Cooling Towers

... because temperature matters

IMT - B 4

Benefits Different Construction Material Options To meat each customers technical and economic requirement, IMT cooling towers offer a broad choice of construction materials such as :

IMT

z

z

z

Fibreglass Reinforced Polyester cladding with a hot dip galvanised steel structure Z600 hot dip galvanised cladding and structure protected with the unique Baltibond Corrosion Protection System. Fibreglass Reinforced Polyester cladding with a stainless steel structure

Choice of Heat Transfer Surface Alternatives In addition to the standard IMT heat transfer surface, heavy duty cleanable fill material (for dirty water applications) and clean water fill are available.

Total Lower Installed Cost z

Modular Design - The time consuming field assembly of individual parts is reduced to the rigging of large factory assembled sections and final assembly details. Your own construction people can receive the shipment, assemble the modules and component parts, and complete the cooling tower installation in a fraction of time required for conventional field erected cooling towers. Less construction time on site means less susceptibility to the variables of weather, labour productivity and workmanship. Field cutting, patching and drilling are virtually eliminated by use of standardized modular sections. The result is the consistent high quality, quickly assembled installation required by today’s industrial cooling tower user.

Hoist heat transfer modules from truck to concrete basin

Baltimore Aircoil

Mount mechanical drive system

IMT - B 5

Install miscellaneous components

Low Sound and Low kW IMT Cooling towers offer low year round energy consumption, and moderately low noise levels, which can be reduced by approx. 6-8 dB(A) on the low speed of two speed fan motors. Low kW custom models are available for even lower energy consumption and lower noise levels.

... because temperature matters

Open Cooling Towers

Assemble and position fan stack and plenum sections.

IMT - B 6

IMT

Construction Details

1. Wet Deck Surface z

Efficient plastic heat transfer surface suitable for most industrial applications

z

Impervious to rot, decay and biological attack

2. Steel Frame z

Heavy duty steel structural angles connected with corresponding hardware

3. FRP casing z

Fibreglass reinforced (FRP) fan stack

4. Axial Fan z

Heavy duty, extruded aluminium axial fan, with maximum fan efficiency

z

Safe fan selection distant from critical fan speed or resonant frequency’s

Baltimore Aircoil

IMT - B 7

5. Drift Eliminators z

UV resistant non-corrosive material, impervious to rot, decay and biological attack

z

Three distinct changes in air direction to reduce drift loss significantly

z

Assembled in easy to handle sections, which can be removed for access to the equipment interior

z

Standard on models IMT 650 and larger.

z

Optional on models IMT 500 up to 650.

z

Right angle double reduction gear with AGMA rating of 2 according PCMA.

7. Access Door z

Large sized access door in the fan plenum.

8. Fan Motor z

TEFC fan motor, IP 55 protected and Class F insulation designed for cooling tower operation.

z

Extra moisture protection on bearings

9. FRP Fan Cylinder z

Fibreglass reinforced (FRP) fan stack

10. Water Distribution System z

Heavy duty spray branches

z

Low pressure, large diameter, non clog nozzles.

11. Belt Drive (Not Shown) Standard on models IMT 500 – 650 with z

Specially designed belt with corrosion resistant fan sheave.

z

Heavy duty grease lubricated ball bearings with moisture seals and integral slinger rings

12. Cold Water Sump (Not Shown) z

Factory assembled sump available for models IMT 500 – 990 (for BBCPS unit execution only)

13. Combined Inlet Shields z

Corrosion Resistant

z

Easily removable

z

UV resistant plastic material

... because temperature matters

Open Cooling Towers

6. Gear Drive System

IMT - B 8

Custom Features and Options

IMT

Construction Options z

Standard Construction: All Z600 heavy-gauge galvanized steel structural elements are protected with the Baltibond® Corrosion Protection System, a hybrid polymer coating used to extend equipment life.

z

Optional Construction: All heavy steel structural elements are hot-dip galvanized after fabrication.

z

Optional Stainless Steel Construction: Structural elements are constructed of stainless steel either type 304 or 316.

Note: Refer to section Technical Resources, Material Options for more details on the materials described above.

Standard Baltibond® Corrosion Protection System (BBCPS)

Optional Hot-Dip Galvanized Structure

Optional Stainless Steel Structure

Cold Water Sump*

Z 600 Galvanized Steel with BBCPS

Not Available

Not Available

Cladding

Z 600 Galvanized Steel with BBCPS

Fiberglass Reinforced Polyester

Fiberglass Reinforced Polyester

Fan Cowl

Fiberglass Reinforced Polyester

Fiberglass Reinforced Polyester

Fiberglass Reinforced Polyester

Frame and Support Columns

Z 600 Galvanized Steel with BBCPS

Steel Hot-Dip Galvanized after Fabrication

304 or 316 Stainless Steel

* Optional on models IMT 500 to 990.

Baltiguard® Drive System (Optional on IMT-500 to 650) The BALTIGUARD® Drive System consists of two standard single-speed fan motors and drive assemblies. One drive assembly is sized for full speed and load, and the other is sized for approximately 2/3 speed and consumes only 1/3 of the design kilowatt power. This configuration allows the system to be operated like a two-speed motor, but with the reserve capacity of a standby motor in the event of failure. As a minimum, approximately 70% capacity will be available from the low kilowatt motor, even on a design wet-bulb Baltiguard® Drive System day. Controls and wiring are the same, as those required for a two-speed, two-winding motor. Significant energy savings are achieved when operating at low speed during periods of reduced load and/or low wet-bulb temperatures.

Combined Inlet Shields Combined Inlet shields prevent biological growth from sunlight, act as a filter for air borne impurities and debris and eliminate water splash out.

Baltimore Aircoil

IMT - B 9

Wetdeck Surface z

z

Optional Film-Type Space 12 mm: For applications where the cooling tower water is clean, alternative models with 12 mm fill are available.

Telescopic fill supports (only for heavy duty 26 mm Fill Type)

Heavy Duty 26 mm Fill Type: Heavier contamination, which results in a heavy accumulation on the heat transfer surface, requires a higher structural strength than can be accomplished with film-type. For such situations, a heat transfer surface is available, constructed of heavy-duty wave formed FRP panels spaced 26 mm apart. With the unique integrated telescopic fill supports, the FRP fill panels can easily be removed for cleaning.

Cold Water Basin Integral cold water basins are available as an option on IMT models 500 to 990 and models IMT500-2 to 990-2 (for IMT-models with the Baltibond® construction only).

Model No. IMT

Sump Height (mm)

Sump Weight (kg)

Sump Volume (l) (1)

Make Up Size ND (mm)

Water Outlet Size ND (mm)

Equalizer Size ND (mm)

IMT 500

510

2090

5690

50

(2x) 250

(2x) 250

IMT 630

510

2090

5690

50

(2x) 250

(2x) 250

IMT 650

510

2500

7120

40

(2x) 250

(2x) 250

IMT-760

510

2500

7120

40

(2x) 250

(2x) 250

IMT 795

510

2730

8480

50

(2x) 300

(2x) 250

IMT 990

510

2730

8480

50

(2x) 300

(2x) 250

Note: (1) Volume at overflow height

Low Sound Fan To maintain the quality of the local environment, the IMT cooling tower can be furnished with a low sound fan.

... because temperature matters

Open Cooling Towers

z

Standard Heat Transfer Surface: The filmtype heat transfer surface supplied as standard with the cooling towers has been carefully selected for industrial applications. The 19 mm spacing between the surface sheets gives excellent air/water contact with low air pressure loss. The standard heat transfer surface provides high thermal efficiency and is sufficient to avoid clogging in most environments.

IMT - B 10

Accessories Electric Water Level Control Package

IMT

The electric water level control to allow replaces the standard mechanical make-up valve when a more precise water level control is required. This package consists of a float switch mounted in the basin and a solenoid activated valve in the make-up water line. The valve is slow closing to minimize water hammer. (Only for models IMT 500 up to IMT 990 with factory supplied basin.)

Vibration Cutout Switch A factory-mounted vibration cut-out switch is available to effectively protect against equipment failure due to excessive vibration of the mechanical equipment system. BAC can provide a vibration cut-out switch in an IP65 enclosure to ensure reliable protection.

Two-Speed Fan Motor An effective method of adding steps of capacity control and saving energy is the installation of twospeed fan motors in lieu of the standard single-speed motors. Two-speed motors are ideally suited for this purpose. At half fan speed the equipment capacity is still about 60% of design whereas the drawn fan power is only about 20% of the full speed motor power. In addition, at low speed, sound levels will generally reduce by about 9 dB(A).

Basin Heaters Units exposed to below freezing ambient temperatures require protection to prevent freezing of the water in the cold water basin when the unit is idle. Factory-installed heaters, which maintain the water temperature at 4°C, are a simple and inexpensive way of providing such protection. The heater package includes the heaters, a thermostat and a low level cut out switch to protect the heaters if the water level is too low. Standard electric heaters are selected for -18°C ambient temperature. (Only for models IMT 500 up to IMT 990 with factory supplied basin)

Model No. IMT

Heaters -18°C (kW)

IMT 500-630

2x8

IMT 650-760

4x5

IMT 795-990

4x6

Fan Motor Control Thermostat Single stage thermostats or two stage thermostats can be used for fan motor speed control.

Safety Switch Safety switches or local isolators allow the electrical supply to motors to be disconnected for safety purposes during inspection or maintenance.

Ladder and Safety Cage These items are available for field installation on all IMT models when required.

Baltimore Aircoil

IMT - B 11

Engineering Data REMARK: Do not use for construction. Refer to factory certified dimensions & weights. This brochure includes data current at time of publication, which should be reconfirmed at the time of purchase. In the interest of product improvement, specifications, weights and dimensions are subject to change without notice. Up-to-date engineering data and more can be found at www.BaltimoreAircoil.com.

1. Water Inlet; 2. Access Door; 3. Motor System (Gear Drive Option); 4. Concrete Basin (by Others).

Model No. IMT

Operating Weight (kg)

Shipping Weight (kg)

Heaviest Section (kg)

H (mm)

Water In L (mm)

W (mm)

Airflow m3/s

Motor (kW)

Water In ND (mm)

IMT 500-1B O

6430

4690

1460

5110

4800

4880

78,8

22

(2x) 200

IMT 630-1B O IMT 630-1B P

7120 7120

5000 5000

1620 1620

5410 5410

4800 4800

4880 4880

74,8 82,1

22 30

(2x) 200 (2x) 200

IMT 650-1B P IMT 650-1B Q

7980 7980

5550 5550

1820 1820

5410 5410

4800 4800

6080 6080

94,4 102,7

30 37

(2x) 250 (2x) 250

IMT 760-1B R

9020

6140

2120

5710

4800

6080

102,7

45

(2x) 250

IMT 795-1B Q IMT 795-1B R

9840 9840

6850 6850

2050 2050

5410 5410

6000 6000

6080 6080

124,1 128,7

37 45

(2x) 250 (2x) 250

IMT 990-1B Q IMT 990-1B R

10950 10950

7390 7390

2320 2320

5710 5710

6000 6000

6080 6080

116,6 126,3

37 45

(2x) 250 (2x) 250

IMT 925-1B R

11820

7820

2440

5720

6000

7280

151,8

45

(2x) 300

IMT 1195-1B R IMT 1195-1B S

13410 13410

8730 8730

2890 2890

6020 6020

6000 6000

7280 7280

143,3 151,8

45 55

(2x) 300 (2x) 300

... because temperature matters

Open Cooling Towers

IMT 500 - 1195

IMT - B 12

IMT

IMT 1155 - 1945

1. Water Inlet; 2. Access Door; 3. Fan Motor System (Gear Drive Option); 4. Concrete Basin (by others).

Model No. IMT

Operating Weight (kg)

Shipping Weight (kg)

Heaviest Section (kg)

H (mm)

Water In L (mm)

W (mm)

Airflow (m3/s)

Motor (kW)

Water Inlet ND (mm)

IMT 1155-1B S

13890

9280

2030

5720

7200

7280

184,2

55

(3x) 250

IMT 1360-1B T

15430

10020

2280

6020

7200

7280

182,6

75

(3x) 250

IMT 1550-1B S IMT 1550-1B T

20900 20900

13600 13600

3300 3300

6570 6570

7200 7200

8480 8480

188,8 200,6

55 75

(3x) 300 (3x) 300

IMT 1695-1B T IMT 1695-1B U

21400 21400

14100 14100

3300 3300

6570 6570

7200 7200

8480 8480

192,1 210,5

75 90

(3x) 300 (3x) 300

IMT 1780-1B U IMT 1780-1B V

23400 23400

15800 15800

4200 4200

6570 6570

8400 8400

8480 8480

237,4 248,8

90 110

(3x) 300 (3x) 300

IMT 1945-1B U IMT 1945-1B V

24000 24000

16400 16400

4200 4200

6570 6570

8400 8400

8480 8480

227,5 245,4

90 110

(3x) 300 (3x) 300

Baltimore Aircoil

IMT - B 13

IMT 1990 - 2530

Model No. IMT

Operating Weight (kg)

Shipping Weight (kg)

Heaviest Section (kg)

H (mm)

Water In L (mm)

W (mm)

Airflow (m3/s)

Motor (kW)

Water Inlet ND (mm)

IMT 1990-1B U IMT 1990-1B V

27600 27600

17900 17900

3300 3300

6570 6570

9600 9600

8480 8480

270,9 284,8

90 110

(4x) 300 (4x) 300

IMT 2260-1B V IMT 2260-1B W

28300 28300

18600 18600

3300 3300

6570 6570

9600 9600

8480 8480

271,7 285,3

110 132

(4x) 300 (4x) 300

IMT 2320-1B V IMT 2320-1B W

31200 31200

20000 20000

3700 3700

7230 7230

9600 9600

9680 9680

309,1 327,4

110 132

(4x) 300 (4x) 300

IMT 2530-1B V IMT 2530-1B W

32000 32000

20800 20800

2700 2700

7230 7230

9600 9600

9680 9680

297,3 314,6

110 132

(4x) 300 (4x) 300

General Notes 1. Special models with alternative configurations, fan power options or heat transfer surface options are available. Contact your BAC Balticare Representative for information. IMT models 500 to 990 are also available with sump as an option. Contact your local BAC Balticare Representative for sump dimensions of these models.

2. Motors located inside the fan plenum for models IMT-500 to IMT650.

... because temperature matters

Open Cooling Towers

1. Water Inlet; 2. Access Door; 3. Fan Motor System (Gear Drive Option); 4. Concrete Basin (by others).

IMT - B 14

Structural Support REMARK: Do not use for construction. Refer to factory certified dimensions & weights. This brochure includes data

IMT

current at time of publication, which should be reconfirmed at the time of purchase. In the interest of product improvement, specifications, weights and dimensions are subject to change without notice. Up-to-date engineering data and more can be found at www.BaltimoreAircoil.com.

IMT 500 - 1195

Baltimore Aircoil

IMT - B 15

Model No. IMT

A (mm)

B (mm)

C (mm)

D (mm)

E (mm)

F (mm)

Support Points (Concrete Sump)

IMT 500-1B O IMT 500-1B P

5204

5294

2310

4710

2310

2400

(12) x M 12

IMT 630-1B P IMT 630-1B Q

5204

5294

2310

4710

2310

2400

(12) x M 12

IMT 650-1B Q IMT 650-1B R

5204

6494

2310

5910

2910

3000

(12) x M 12

5204

6494

2310

5910

2910

3000

(12) x M 12

6404

6494

2910

5910

2910

3000

(12) x M 12

IMT 990-1B R IMT 990-1B S

6404

6494

2910

5910

2910

3000

(12) x M 12

IMT 925-1B S

6404

7694

2910

7110

3510

3600

(12) x M 12

IMT 1195-1B S IMT 1195-1B T

6404

7694

2910

7110

3510

3600

(12) x M 12

... because temperature matters

Open Cooling Towers

IMT 760-1B R IMT 795-1B Q IMT 795-1B R

IMT - B 16

IMT

IMT 1155 - 1360

Model No. IMT

A (mm)

B (mm)

C (mm)

D (mm)

E (mm)

F (mm)

Support Points (Concrete Sump)

IMT 1155-1B

7604

7694

2310

7110

3510

3600

(18) x M 16

IMT 1360-1B

7604

7694

2310

7110

3510

3600

(18) x M 16

Baltimore Aircoil

IMT - B 17

IMT 1550 - 1945

Open Cooling Towers

Model No. IMT

A (mm)

B (mm)

C (mm)

D (mm)

E (mm)

F (mm)

G (mm)

Support Points (Concrete Sump)

IMT 1550-1B IMT 1550-1B

7604

8894

2310

8310

2910

2400

2490

(24) x M 16

IMT 1695-1B IMT 1695-1B

7604

8894

2310

8310

2910

2400

2490

(24) x M 16

IMT 1780-1B IMT 1780-1B

8804

8894

2910

8310

2910

2400

2490

(24) x M 16

IMT 1945-1B IMT 1945-1B

8804

8894

2910

8310

2910

2400

2490

(24) x M 16

... because temperature matters

IMT - B 18

IMT

IMT 1990 - 2530

Model No. IMT

A (mm)

B (mm)

C (mm)

D (mm)

E (mm)

F (mm)

G (mm)

Support Points (Concrete Sump)

IMT 1990-1B IMT 1990-1B

10004

8894

2310

8310

2910

2490

2400

(32) x M 16

IMT 2260-1B IMT 2260-1B

10004

8894

2310

8310

2910

2490

2400

(32) x M 16

IMT 2320-1B IMT 2320-1B

10004

10094

2310

9510

3510

2490

2400

(32) x M 16

IMT 2530-1B IMT 2530-1B

10004

10094

2310

9510

3510

2490

2400

(32) x M 16

Notes: IMT Cooling Towers provided without the integral sump by BAC should be supported on concrete columns or sump walls as shown. Dimensions A en B show the minimum inside sump dimensions and the table above gives the total number of support points required in the sump. For exact support locations of double cell models refer to foundation drawing available from your BAC Balticare Representative.

Baltimore Aircoil

IMT - B 19

Engineering Specifications 1.0 Cooling Tower

1.2 Thermal Capacity: The cooling tower(s) shall be warranted by the manufacturer to cool _____ l/s of water from ______ °C to _____°C at _____°C entering wet-bulb temperature. 1.3 Corrosion Resistant Construction: Unless otherwise noted in this specification, all steel panels and structural members shall be protected with the BALTIBOND® Corrosion Protection System. The system shall consist of Z600 metric hot-dip galvanized steel prepared in a four-step (clean, pre-treat, rinse, dry) process with an electrostatically sprayed, thermosetting, hybrid polymer fuse-bonded to the substrate during a thermally activated curing stage and monitored by a 23-step quality assurance program. Casing panels shall be constructed of corrosion and UV-resistant fibreglass

reinforced polyester (FRP) to minimise maintenance requirements and prolong equipment life (Alternate 1.3) Corrosion Resistant Construction: Unless otherwise noted in this specification, all structural members shall be constructed of heavy-gauge steel hot dip galvanized after fabrication. Casing panels shall be constructed of corrosion and UV-resistant fibreglass reinforced polyester (FRP) to minimise maintenance requirements and prolong equipment life. (Alternate 1.3) Type 304 or 316 Stainless Steel Construction: All structural members shall be constructed of Type 304 or 316L stainless steel. Casing panels shall be constructed of corrosion and UV-resistant fibreglass reinforced polyester (FRP) to minimise maintenance requirements and prolong equipment life 1.4 Quality Assurance: The cooling tower manufacturer shall have a Management System certified by an accredited registrar as complying with the requirements of ISO-9001:2000 to ensure consistent quality of products and services. 1.5 Warranty: The manufacturer’s standard equipment warranty shall be for a period of not less than one year from date of startup or eighteen months from date of shipment, whichever occurs first.

2.0 Construction Details 2.1 Structure: The cooling tower structure shall be made of Z600 metric hot-dip galvanised steel protected with the BALTIBOND ® Corrosion Protection System. 2.2 Casing Panels and Fan Deck: Casing panels shall be constructed of corrosion and UV-resistant fibreglass reinforced polyester (FRP) to minimise maintenance requirements and prolong equipment life. 2.3 Support Columns: The cooling tower heat transfer surface sections shall have integral support columns. The columns shall be constructed from heavy gauge galvanized steel angles which recess into the heat transfer section to reduce shipping volume. 2.4 Sump: (Optional for models IMT 500-990 and models IMT 500-2 – 990-2 and only for units protected with the Baltibond® Corrosion

Protection System.) The integral sump shall be constructed of heavy gauge Z600 Hot dip galvanized steel. Standard accessories shall include large area, liftout, galvanized strainers with BALTIBOND® Corrosion Protection System and perforated openings, sized smaller than the water distribution nozzle orifices; an integral anti-vortexing hood to prevent air entrainment, brass make-up valve with larger diameter plastic float arrangement for easy adjustment (field installed) and connections for water outlet, overflow and drain. 2.5. Fans: Fans shall be axial flow type constructed of heavy duty aluminium, and tested in actual models by the cooling tower manufacturer. Each fan cylinder shall be designed for streamlined air entry and minimum tip clearance for maximum fan efficiency.

3.0 Mechanical Equipment 3.1. Belt Drive (models IMT 500-650): Fans shall be driven by neoprene/polyester belt(s) designed specifically for cooling tower service. The sheaves shall be cast aluminum. Fan shaft shall be mounted in heavy duty, grease-packed, self-aligning relubricatable ball bearings with moisture proof seals and integral slinger rings. Extended lube lines shall be provided for ease of maintenance.

3.2. Gear Drive (models IMT 650 and larger, optional on models IMT 500-650): Fan shall be driven through a right angle gear box designed for a service factor of 2 according to PCMA. 3.3. Fan Motors: The fan motor(s) shall be ______ kW, 1500 RPM, squirrel cage, totally enclosed, fan cooled (TEFC) with IP55 protection and Class F insulation. Motor(s) shall be specifically designed for cooling tower service and shall have special moisture protection on windings, shaft and bearings.

4.0 Wet Deck Surface and Drift Eliminators 4.1. Wet Deck Surface: The wet deck surface shall consist of plastic formed sheets. It shall be impervious to rot, decay and fungus or biological attack. The surface shall be performance tested in actual models by the cooling tower manufacturer to assure specified performance.

4.2. Drift Eliminators: Eliminators shall be constructed of formed plastic sheets and be removable in easily handled sections. They shall have a minimum of three changes in air direction.

5.0 Combined Inlet Shields 5.1. Combined Inlet Shields: Combined inlet shields shall be separate from the wet deck surface and removable to allow easy access for inspection of the air/water interface at the air inlet side of the equipment. Combined inlet shields shall prevent UV-light and

debris from entering the unit, as well as prevent water splash out during fan cycling. They shall be constructed of maintenance free, corrosion and UV resistant material.

... because temperature matters

Open Cooling Towers

1.1 General: Furnish and install _____ factory-assembled, induceddraft, axial fan, counterflow cooling tower(s) with vertical air discharge, conforming in all aspects to the specifications, schedules and as shown on the plans. Overall dimensions shall not exceed approximately _____ mm long x ______ mm wide x _____ mm high. The total connected fan kW shall not exceed _____ kW. The cooling tower(s) shall be Baltimore Aircoil Model ____________.

IMT - B 20

6.0 Access 6.1. Access : Access doors for inspection of the internal components of the tower shall be installed on the plenum above the drift eliminators.

7.0 Sound

IMT

7.1 Sound Level: To maintain the quality of the local environment, the maximum sound pressure levels (dB) measured 15 m from the

Location

63

125

250

cooling tower operating at full fan speed shall not exceed the sound levels detailed below.

500

Discharge Air Inlet End Back

Baltimore Aircoil

1000

2000

4000

8000

DB(A)

VTL - B 1

VTL

Open Cooling Towers

Open Cooling Towers

.

Product Detail VTL Open Cooling Towers ....................................................................... B2 Benefits ....................................................................................................... B4 Construction Details .................................................................................. B6 Custom Features and Options .................................................................. B7 Accessories ................................................................................................. B9 Engineering Data ...................................................................................... B11 Structural Support .................................................................................. B15 Engineering Specifications ..................................................................... B16

VTL - B 2

VTL Open Cooling Towers Capacity Single Cell Capacity:

VTL

4 – 90 l/s

General Description Open Circuit Cooling Towers with centrifugal fans, deliver fully rated thermal performance over a wide range of flow and temperature requirements. This type of cooling towers can be installed indoors and can accommodate limited ceiling or enclosure heights. Cooling towers with centrifugal fans minimise sound levels and installation costs, provide year round operating reliability, and simplify maintenance requirements. Cooling Towers provide an answer to the growing need to save water and energy and help protect the environment by providing the highest system efficiency.

Key Features z

Suitable for indoor and outdoor installations

z

Suitable for high temperature applications

z

Low sound

z

Single side air inlet

z

Low energy consumption

z

Low installed costs

z

Easy maintenance

z

Reliable year-round operation

z

Long service life

z

Suitable for locations with limited ceiling or enclosure heights and roof top installations

.

Baltimore Aircoil

VTL - B 3

Open Cooling Towers

... because temperature matters

VTL - B 4

Benefits Installation and Application Flexibility

VTL

z

z

z

Indoor Installations – Centrifugal fans can overcome the static pressure imposed by external ductwork, allowing this type of cooling towers to be installed indoors. High Temperature Applications – A range of wet deck and construction options are available to accommodate entering water temperatures of up to 65°C. Low Profile Models – Motors and drive of low profile units are adjacent to the casing section to yield models suitable for use in height sensitive installations.

Low profile unit shown in contrast to a standard unit

Low Sound z

z

Centrifugal Fan - Centrifugal fans have inherently low sound characteristics. Single Side Air Inlet - Particularly soundsensitive areas can be accommodated by facing the quiet side (back panel) to the soundsensitive direction.

Low Energy Consumption z

Evaporative Cooling Equipment minimizes the energy consumption of the entire system because it provides lower operating temperatures. The owner saves money while conserving natural resources and reducing environmental impact.

Low Installed Cost z

z

Support – All models mount directly on two parallel I-beams (supplied by others) and ship complete with motors and drives, factoryinstalled and aligned. Modular Design – All models without intake or discharge accessories ship in one piece to minimize field installation time and lifting time.

Easy Maintenance z

Internal Access - The interior of the unit is easily accessible for adjusting the float valve, cleaning the strainer or flushing the basin.

Baltimore Aircoil

Modular Design

VTL - B 5

Reliable Year-Round Operation z

V-Belt Drive – The fans, motor, and drive system are located outside of the moist discharge airstream, protecting them from moisture, condensation and icing hence allowing a safe yearround operation.

V-Belt Drive System for Series VL-units

Long Service Life z

Materials of Construction – Various materials are available to meet the corrosion resistance, unit operating life, and budgetary requirements of any project.

Note: For more information, please refer to the section “Technical Resources, Materials of Construction”.

... because temperature matters

Open Cooling Towers

The water level control is easily reached from the access door

VTL - B 6

Construction Details

VTL

.

1. Heavy-Duty Construction z

Z600 hot-dip galvanized steel panels

2. Fan Drive System

z

Impervious to rot, decay and biological attack

z

Self extinguishing

z

High temperature wet deck option

z

V-belt drive

6. Strainer

z

Heavy-duty bearings and fan motor

z

3. Low sound Centrifugal Fan(s) z

Quiet Operation

z

Plastic spray header and branches

z

Large orifice, non-clog nozzles

z

Grommetted for easy maintenance

5. BACount® Wet Deck Surface z

7. Access Door z

4. Water Distribution System

Anti-vortex design to prevent air entrainment

Circular access door

8. Drift Eliminators z

UV resistant non-corrosive material, impervious to rot, decay and biological attack

z

Three distinct changes in air direction to reduce drift loss significantly

z

Assembled in easy to handle sections, which can be removed for access to the equipment interior

Plastic material

Baltimore Aircoil

VTL - B 7

Custom Features and Options Construction Options z

Optional BALTIBOND® Corrosion Protection System: The BALTIBOND® Corrosion Protection System, a hybrid polymer coating used to extend equipment life, is applied before assembly to all hot-dip galvanized steel components of the unit.

z

Optional Stainless Steel Construction: Steel panels and structural elements are constructed of stainless steel either type 304 or 316.

z

Optional Water-Contact Stainless Steel Cold Water Basin: A cost-effective alternative to an all stainless steel unit. The critical components in the cold water basin and the cold water basin itself are provided in stainless steel. The remaining components are protected with the BALTIBOND® Corrosion Protection System.

Note: See section Technical Resources, Material of Construction for more details on the materials described above.

Fan Drive System The fan drive system provides the cooling air necessary to reject heat from the system to the atmosphere. Centrifugal fans, forwardly curved, are driven by matched V-belts with taper lock sheaves.

Baltiguard® Drive System The BALTIGUARD® Drive System consists of two standard single-speed fan motors and drive assemblies. One drive assembly is sized for full speed and load, and the other is sized for approximately 2/3 speed and consumes only 1/3 of the design kilowatt power. This configuration allows the system to be operated like a two-speed motor, but with the reserve capacity of a standby motor in the event of failure. As a minimum, approximately 70% capacity will be available from the low kilowatt motor, even on a design wet-bulb day. Controls and wiring are the same, as those required for a two-speed, two-winding motor. Significant energy savings are achieved when operating at low speed during periods of reduced load and/or low wet-bulb temperatures.

Baltiguard® Drive System

Unit with Sound Attenuation

... because temperature matters

Open Cooling Towers

z

Standard Construction: Steel panels and structural elements are constructed of Z600 heavy-gauge hot-dip galvanized steel protected with the Baltiplus Corrosion Protection on the outside of the unit.

VTL - B 8

VTL

Low Sound Operation The low sound levels generated by BAC Products with centrifugal fans make them suitable for most installations. For situations when one direction is particularly sound sensitive, the unit can be oriented so that the side opposite the air inlet faces the sound-sensitive direction. Units with centrifugal fans are also available with factory designed, tested and rated sound attenuation for both the air inlet and discharge. Note: For more information, please refer to the section “Technical Resources, Sound Reduction Options”.

Remote Sump Execution

Unit with Intake and Discharge Sound Attenuation

The use of an auxiliary sump within a heated space is the most satisfactory way to protect sump water from freezing. When the circulating pump is shut off, all the water in the water distribution, in suspension and in the sump will drain freely to the auxiliary sump. Note: For detailed information on the calculation of the remote sump tank, please refer to the section "Technical Resources, Selection of Remote Sump Tank".

High Temperature Wet Deck If operation above 55°C is anticipated, an optional high temperature wet deck material is available which increases the maximum allowable entering water temperature to 65°C.

Baltimore Aircoil

VTL - B 9

Accessories Basin Heaters

Model No. VTL

Heaters -18 °C (kW)

VTL 039-072

1x3

VTL 076

1x4

VTL 079

1x3

VTL 082

1x4

VTL 086-094

1x5

VTL 095

1x4

VTL 103-137

1x5

VTL 139-215

2x4

VTL 225

2x5

VTL 227

2x4

VTL 238-272

2x5

Electric Water Level Control Package The electric water level control replaces the standard mechanical make-up valve when a more precise water level control is required. This package consists of a float switch mounted in the basin and a solenoid activated valve in the makeup water line. The valve is slow closing to minimize water hammer.

Extended Lubrication Lines Extended lubrication lines with grease fittings are available for lubrication of the fan shaft bearings. Electric Water Level Control Package

Capacity Control Dampers Modulating capacity control dampers are available to provide better leaving water temperature control than can be obtained from fan cycling alone. Fan discharge dampers consist of a single airfoil type damper blade located in the discharge of each fan housing. A standard electrical control package for dampers is available from BAC.

... because temperature matters

Open Cooling Towers

Units exposed to below freezing ambient temperatures require protection to prevent freezing of the water in the cold water basin when the unit is idle. Factory-installed heaters, which maintain the water temperature at 4°C, are a simple and inexpensive way of providing such protection. The heater package includes the heaters, a thermostat and a low level cut out switch to protect the heaters if the water level is too low. Standard electric heaters are selected for -18°C ambient temperature.

VTL - B 10

Basin Sweeper Piping Basin sweeper piping provides an effective method of preventing sediment from collecting in the cold water basin of the unit. A complete piping system, including nozzles, is provided in the unit basin for connection to side stream filtration equipment. Note: For more information, please refer to the section "Technical Resources, Filtration".

VTL

Discharge Hoods Discharge hoods reduce the risk of re-circulation in tight enclosures by increasing discharge air velocity, and can be used to elevate the unit discharge above adjacent walls to comply with layout guidelines.

Baltimore Aircoil

VTL - B 11

Engineering Data REMARK: Do not use for construction. Refer to factory certified dimensions & weights. This brochure includes data current at time of publication, which should be reconfirmed at the time of purchase. In the interest of product improvement, specifications, weights and dimensions are subject to change without notice. Up-to-date engineering data and more can be found at www.BaltimoreAircoil.com.

VTL 039 G - VTL 137 M

Model VTL

Operating Shipping Heaviest Weight Weight Section (kg) (kg) (kg)

H (mm)

L1 (mm)

L2 (mm)

W (mm)

A (mm)

Air Flow (m3/s)

Fan Motor (kW)

Fluid Inlet ND (mm)

Fluid Make Up Outlet ND (mm) ND (mm)

VTL 039-G VTL 045-H VTL 052-H VTL 059-H VTL 059-J VTL 066-J VTL 072-K VTL 076-J VTL 079-K

1200 1230 1260 1290 1310 1320 1330 1720 1410

720 750 780 810 830 840 850 1010 930

720 750 780 810 830 840 850 1010 930

1560 1560 1785 1990 1785 1990 1990 1990 2480

3350 3350 3350 3350 3350 3350 3350 4560 3350

1820 1820 1820 1820 1820 1820 1820 2730 1820

1250 1250 1250 1250 1250 1250 1250 1250 1250

75 75 75 75 75 75 75 105 75

7,0 8,0 7,7 7,3 8,6 8,1 8,8 9,7 8,3

(1x) 2,2 (1x) 4,0 (1x) 4,0 (1x) 4,0 (1x) 5,5 (1x) 5,5 (1x) 7,5 (1x) 5,5 (1x) 7,5

(1x) 100 (1x) 100 (1x) 100 (1x) 100 (1x) 100 (1x) 100 (1x) 100 (1x) 150 (1x) 100

(1x) 100 (1x) 100 (1x) 100 (1x) 100 (1x) 100 (1x) 100 (1x) 100 (1x) 150 (1x) 100

25 25 25 25 25 25 25 25 25

VTL 082-K VTL 086-L VTL 094-M VTL 095-K VTL 103-K VTL 116-L VTL 126-L VTL 126-M VTL 137-M

1740 2050 2060 1850 2150 2180 2320 2190 2330

1030 1120 1130 1140 1220 1250 1390 1260 1400

1030 1120 1130 1140 1220 1250 1390 1260 1400

1990 1560 1560 2480 1990 1990 2480 1990 2480

4560 5480 5480 4560 5480 5480 5480 5480 5480

2730 3650 3650 2730 3650 3650 3650 3650 3650

1250 1250 1250 1250 1250 1250 1250 1250 1250

105 105 105 105 105 105 105 105 105

10,6 14,0 15,4 10,0 11,8 13,3 12,8 14,5 13,6

(1x) 7,5 (1x) 11,0 (1x) 15,0 (1x) 7,5 (1x) 7,5 (1x) 11,0 (1x) 11,0 (1x) 15,0 (1x) 15,0

(1x) 150 (1x) 150 (1x) 150 (1x) 150 (1x) 150 (1x) 150 (1x) 150 (1x) 150 (1x) 150

(1x) 150 (1x) 150 (1x) 150 (1x) 150 (1x) 150 (1x) 150 (1x) 150 (1x) 150 (1x) 150

25 25 25 25 25 25 25 25 25

... because temperature matters

Open Cooling Towers

1. Water Inlet; 2. Water Outlet; 3. Access Door; 4. Make up; 5. Overflow ND50; 6. Drain ND50; 7. Fan Motor. Overflow connection is 80 mm on models VTL 086-L, VTL-094-M and VTL 103-K through VTL 137-M.

VTL - B 12

VTL

VTL 139 L - VTL 272 P

1. Water Inlet; 2. Water Outlet; 3. Access Door; 4. Make up; 5. Overflow ND 80; 6. Drain ND 50; 7. Fan Motor.

Model VTL VTL 139-L VTL 152-M VTL 171-L VTL 185-M VTL 198-N VTL 209-O VTL 215-N VTL 225-O VTL 227-O VTL 238-N VTL 245-P VTL 272-P

Operating Shipping Heaviest Weight Weight Section (kg) (kg) (kg) 3000 3010 3100 3170 3190 3200 3380 4000 3400 4110 4080 4310

1560 1570 1670 1740 1760 1770 1950 2080 1970 2210 2180 2410

1560 1570 1670 1740 1760 1770 1950 2080 1970 2210 2180 2410

H (mm)

L1 (mm)

L2 (mm)

W (mm)

A (mm)

Air Flow (m3/s)

Fan Motor (kW)

Fluid Inlet ND (mm)

Fluid Make Up Outlet ND (mm) ND (mm)

1560 1560 1990 1990 1990 1990 2480 1990 2480 2480 1990 2480

4560 4560 4560 4560 4560 4560 4560 5480 4560 5480 5480 5480

2730 2730 2730 2730 2730 2730 2730 3650 2730 3650 3650 3650

2400 2400 2400 2400 2400 2400 2400 2400 2400 2400 2400 2400

130 130 130 130 130 130 130 130 130 130 130 130

19,9 21,6 18,8 20,4 21,8 23,0 20,8 25,5 22,0 23,4 27,8 26,8

(1x) 11,0 (1x) 15,0 (1x) 11,0 (1x) 15,0 (1x) 18,5 (1x) 22,0 (1x) 18,5 (1x) 22,0 (1x) 22,0 (1x) 18,5 (1x) 30,0 (1x) 30,0

(1x) 200 (1x) 200 (1x) 200 (1x) 200 (1x) 200 (1x) 200 (1x) 200 (1x) 200 (1x) 200 (1x) 200 (1x) 200 (1x) 200

(1x) 200 (1x) 200 (1x) 200 (1x) 200 (1x) 200 (1x) 200 (1x) 200 (1x) 200 (1x) 200 (1x) 200 (1x) 200 (1x) 200

50 50 50 50 50 50 50 50 50 50 50 50

General Notes 1. All connections 100 mm and smaller are MPT. Connections larger than 100 mm are bevelled-for-welding. 2. Fan kW is at 0 Pa ESP. To operate against external static pressure up to 125 Pa, consult your local BAC Balticare Representative for size and location.

4. Unit height is indicative, for precise value refer to certified print. 5. Shipping/operating weights indicated are for units without accessories such as sound attenuators, discharge hoods, etc. Consult factory certified prints to obtain weight additions and the heaviest section to be lifted.

3. Make up, overflow, suction, drain connections and access door can be provided on side opposite to that shown; consult your BAC representative.

Baltimore Aircoil

VTL - B 13

Sound Attenuation HS Horizontal Intake Sound Attenuation

HD Horizontal Intake Sound Attenuation

1.Discharge attenuator, 2. Access Door, 3. Intake Attenuator; H & W: unit height and width (see engineering data).

... because temperature matters

Open Cooling Towers

1.Discharge attenuator, 2. Access Door, 3. Intake Attenuator; H & W: unit height and width (see engineering data).

VTL - B 14

VTL

VS Vertical Intake Sound Attenuation

1.Discharge attenuator, 2. Access Door, 3. Intake Attenuator, 4. Plenum; H & W: unit height and width (see engineering data).

Dimensions (mm) Model No VTL

L2

Weight (kg) L1

Intake Attenuator

Discharge Attenuator

Total

HS

HD

VS

HS,HD,VS

HS

HD

HS

HD

HS

HD

VS

VTL039 G - 079 K

2390

3125

2010

1820

460

655

215

235

675

890

725

VTL076 J - 095 K

2640

3375

2010

2730

465

660

295

315

760

975

830

VTL086 L - 137 M

2640

3375

2010

3650

465

660

365

385

830

1045

915

VTL139 L - 227 O

2640

3375

2010

2730

665

980

465

500

1130

1480

1205

VTL225 O - 272 P

2640

3375

2010

3650

665

980

565

605

1230

1585

1310

Note: All VL-units with HS, VS or HD attenuators ship in 2 pieces.

Remote Sump Data Refer to the "Technical Resources" section "Selection of Remote Sump" for Remote Sump Data.

Baltimore Aircoil

VTL - B 15

Structural Support REMARK: Do not use for construction. Refer to factory certified dimensions & weights. This brochure includes data current at time of publication, which should be reconfirmed at the time of purchase. In the interest of product improvement, specifications, weights and dimensions are subject to change without notice. Up-to-date engineering data and more can be found at www.BaltimoreAircoil.com. The recommended support arrangement for units consists of parallel I-beams running the full length of the unit, spaced as shown in the following drawing. Besides providing adequate support, the steel also serves to raise the unit above any solid foundation to ensure access to the bottom of the unit. To support units in an alternate steel support arrangement, consult your BAC Balticare Representative.

VTL Cooling Tower Model No.

A (mm)

B (mm)

Maximum Allowable Beam Deflection (mm)

039-G - 072K 079-K

2426

1194

10

076-J 082-K 095-K

3334

1194

13

086-L & 094-M 103-K - 137-M

4253

1194

13

139-L - 215-N 227-O

3334

2344

13

225-O 238-N - 272-P

4253

2344

13

1. (4) Ø 22 mm mounting holes; 2. Support Beams; 3. Fan Side; 4. Outline of Unit; 5. Outline of Attenuator “HS” (optional); 6. Outline of Attenuator “HD” (optional).

Notes: 1. The recommended support arrangement for these units consists of two parallel I-beams extending the full length of the unit. Supports and anchor bolts are to be designed and furnished by others. 2. All supporting beams are to be flush and level at top and must be oriented relative to gage line as shown. 3. Recommended design loads for each unit support beam should be 70% of the total unit operating weight applied as a uniform load to each of the unit beams. Beams should be designed in

accordance with standard structural practice. For the maximum allowable deflection of beams under the unit refer to above table. 4. All mounting holes have a diameter of 22 mm at the locations shown. 5. If vibration isolators are used, a rail or channel must be provided between the unit and the isolators to provide continuous unit support. Additionally the support beams must be designed to accommodate the overall length and mounting hole location of the isolators that may differ from those of the unit. Refer to vibration isolator drawings for these data.

... because temperature matters

Open Cooling Towers

Units with and without Sound Attenuation

VTL - B 16

Engineering Specifications

VTL

1.0 Cooling Tower 1.1 General: Furnish and install _____ factory-assembled, forceddraft, centrifugal fan, counter flow cooling tower(s) with vertical air discharge, conforming in all aspects to the specifications, schedules and as shown on the plans. Overall dimensions shall not exceed approximately _____ mm long x ______ mm wide x _____ mm high. The total connected fan power shall not exceed _____ kW. The cooling tower(s) shall be Baltimore Aircoil Model ____________. 1.2 Thermal Capacity: The cooling tower(s) shall be warranted by the manufacturer to cool _____ l/s of water from ______ °C to _____C at _____°C entering wet-bulb temperature. 1.3 Corrosion Resistant Construction (standard): Unless otherwise noted in this specification, all steel panels and structural members shall be constructed of heavy-gauge Z600 metric hot-dip galvanized steel with all edges given a protective coating of zinc-rich compound and the exterior protected with the BALTIPLUS Protection. (Alternate 1.3) Corrosion Resistant Construction (optional): Unless otherwise noted in this specification, all steel panels and structural members shall be protected with the BALTIBOND®

Corrosion Protection System. The system shall consist of Z600 metric hot-dip galvanized steel prepared in a four-step (clean, pre-treat, rinse, dry) process with an electrostatically sprayed, thermosetting, hybrid polymer fuse-bonded to the substrate during a thermally activated curing stage and monitored by a 23-step quality assurance program. (Alternate 1.3) Corrosion Resistant Construction (optional): Unless otherwise noted in this specification, all steel panels and structural members shall be constructed of Type 304 or 316 stainless steel and assembled with stainless steel nut and bolt fasteners. 1.4 Quality Assurance: The cooling tower manufacturer shall have a Management System certified by an accredited registrar as complying with the requirements of ISO-9001:2000 to ensure consistent quality of products and services. 1.5 Warranty: The manufacturer’s standard equipment warranty shall be for a period of not less than one year from date of startup or eighteen months from date of shipment, whichever occurs first.

2.0 Construction Details 2.1 Structure: The unit shall be constructed of heavy-gauge steel utilizing double-brake flanges for maximum strength and rigidity and reliable sealing of watertight joints. The unit shall be of unitary design to minimize rigging requirements. The fan(s) and fan drive system, including the fan motor, shall be factory mounted and aligned and located in the dry entering air stream to ensure reliable operation and ease of maintenance. 2.2 Heat Transfer Section: The heat transfer sections(s) shall consist of a wet deck surface, spray water distribution system and drift eliminators arranged for optimal thermal performance with minimal drift. 2.3 Wet Deck Surface: The wet deck surface shall be formed from self-extinguishing plastic material and shall be impervious to rot, decay, and fungus or biological attack. The wet deck surface shall be manufactured and performance tested by the cooling tower manufacturer to assure single source responsibility and control of the final product. 2.4 Water Distribution System: Water shall be distributed evenly over the wet deck surface by a water distribution system consisting of a header and spray branches of plastic pipe with large orifice, nonclog plastic distribution nozzles. The branches and spray nozzles shall be held in place by snap-in rubber grommets, allowing quick

removal of individual nozzles or complete branches for cleaning or flushing. 2.5 Cold Water Basin: The cold water basin shall be provided with large area lift out strainers with perforated openings sized smaller than the water distribution system nozzles and an anti-vortexing device to prevent air entrainment. The strainer and anti-vortexing device shall be constructed of the same material as the basin to prevent dissimilar metal corrosion. Standard basin accessories shall include a brass make-up valve with large diameter polystyrene filled plastic float for easy adjustment of the operating water level. (Alternate2.5) Cold Water Basin: The cold water basin shall be constructed of heavy-gauge Type 304 or 316 stainless steel panels and structural members up to the heat transfer section/basin joint. The basin shall be provided with large area lift out strainers with perforated openings sized smaller than the water distribution system nozzles and an anti-vortexing device to prevent air entrainment. The strainer and anti-vortexing device shall be constructed of the same material as the basin to prevent dissimilar metal corrosion. Standard basin accessories shall include a brass make-up valve with large diameter polystyrene filled plastic float for easy adjustment of the operating water level.

3.0 Mechanical Equipment 3.1 Fan(s): Fan(s) shall be dynamically balanced, forwardly curved, centrifugal type selected to provide optimum thermal performance with minimal sound levels. Fan housings shall have curved inlet rings for efficient air entry and four-sided rectangular discharge cowls shall extend into the basin to increase fan efficiency and prevent water from splashing into the fans. 3.2 Bearings: Fan(s) and shaft(s) shall be supported by heavy-duty, self-aligning, relubricatable bearings with cast iron housings, designed for a minimum L10 life of 40 000 hours (280 000 Hr. Average. Life). 3.3 Fan Drive: The fan(s) shall be driven by matched V-belts with taper lock sheaves. Motor shall be located on a heavy-duty motor

base, adjustable by a single threaded bolt-and-nut arrangement. Removable steel screens or panels shall protect the fan drive and all moving parts. 3.4 Fan Motor: Furnish _____ kW, ______ RPM Totally Enclosed, Fan Cooled (TEFC), squirrel cage, ball bearing type fan motors suitable for outdoor service. Motor(s) shall be suitable for ________ volt, ___ hertz, and __ phase electrical service. 3.5 BALTIGUARD® Fan System (optional): Two-single speed fan motors, one sized for full speed and load, the other sized for 2/3 speed and approximately 1/3 of full load kW shall be provided in each cell for capacity control and stand-by protection from drive or motor failure. Two-speed motor(s) are not an acceptable alternative.

Baltimore Aircoil

VTL - B 17

4.0 Drift Eliminators 4.1 Drift Eliminators: Eliminators shall be constructed of specially formulated plastic material and be removable in easily handled

sections. They shall have a minimum of three changes in air direction.

5.0 Access 5.1 Basin Access: Circular access doors shall be provided for easy access to the make-up water assembly and suction strainer for

routine maintenance.

6.0 Sound

Location

63

125

250

500

cooling tower operating at full fan speed shall not exceed the sound levels detailed below.

1000

2000

4000

Discharge Air Inlet End Back

... because temperature matters

8000

dB(A)

Open Cooling Towers

6.1 Sound Level: To maintain the quality of the local environment, the maximum sound pressure levels (dB) measured 15 m from the

VXT - B 1

VXT

Open Cooling Towers

Open Cooling Towers

Product Detail VXT Open Cooling Tower ........................................................................ B2 Benefits ....................................................................................................... B4 Construction Details .................................................................................. B6 Custom Features and Options .................................................................. B8 Accessories ............................................................................................... B10 Engineering Data ..................................................................................... B12 Structural Support .................................................................................. B19 Engineering Specifications ..................................................................... B22

VXT - B 2

VXT Open Cooling Tower Capacity Single Cell Capacity:

VXT

From 1,6 l/s to 1230 l/s

General Description Open Circuit Cooling Towers with centrifugal fans, deliver fully rated thermal performance over a wide range of flow and temperature requirements. This type of cooling towers can be installed indoors and can accommodate limited ceiling or enclosure heights. Cooling towers with centrifugal fans minimise sound levels and installation costs, provide year round operating reliability, and simplify maintenance requirements. Cooling Towers provide an answer to the growing need to save water and energy and help protect the environment by providing the highest system efficiency.

Key Features z

Suitable for indoor and outdoor installations

z

Suitable for high temperature applications

z

Low sound

z

Single side air inlet

z

Low energy consumption

z

Low installed cost

z

Easy maintenance

z

Reliable year-round operation

z

Long service life

Baltimore Aircoil

VXT - B 3

Open Cooling Towers

... because temperature matters

VXT - B 4

Benefits Installation and Application Flexibility z

VXT

z

Indoor Installations – Centrifugal fans can overcome the static pressure imposed by external ductwork, allowing this type of cooling towers to be installed indoors. High Temperature Applications – A range of wet deck and construction options are available to accommodate entering water temperatures of up to 65°C.

Low Sound z z

Centrifugal Fan - Centrifugal fans have inherently low sound characteristics. Single Side Air Inlet - Particularly sound-sensitive areas can be accommodated by facing the quiet side (back panel) to the sound-sensitive direction.

Low Energy Consumption z

Evaporative Cooling Equipment minimizes the energy consumption of the entire system because it provides lower operating temperatures. The owner saves money while conserving natural resources and reducing environmental impact.

Low Installed Cost z

z

Support – All models mount directly on two parallel I-beams (supplied by others) and ship complete with motors and drives, factory-installed and aligned. Modular Design – Large models ship in multiple sections to minimize the size and weight of the heaviest lift, allowing for the use of smaller, less costly cranes.

Easy Maintenance z

Internal Access - The interior of the unit is easily accessible for adjusting the float valve, cleaning the strainer or flushing the basin.

The water level control is easily reached from the access door.

External V-belt drive system (shown here with panel removed)

Reliable Year-Round Operation z

V-Belt Drive – The fans, motor, and drive system are located outside of the moist discharge airstream, protecting them from moisture, condensation and icing hence allowing a safe yearround operation.

Baltimore Aircoil

VXT - B 5

Long Service Life z

Materials of Construction – Various materials are available to meet the corrosion resistance, unit operating life, and budgetary requirements of any project.

Note: For more information, please refer to the section “Technical Resources, Materials of Construction”.

Low Ocean Freight Cost z

C Model in Dry Van Container

Fan Enclosures are shipped loose

... because temperature matters

Open Cooling Towers

Size - C models are designed to fit in standard closed box containers to minimize ocean freight costs. All containerized models are shipped in a bottom fan section and a top coil section, which fit together into a 40' box container, no crating required. In order to fit the bottom fan section through the doors of the container, the fan enclosures are shipped loose inside the water basin area and are easily mounted on site.

VXT - B 6

VXT

Construction Details

Upper Section

Lower Section

Baltimore Aircoil

VXT - B 7

1. Heavy Duty Construction z

Z600 hot-dip galvanized steel panels

2. Fan Drive System z

V-belt drive

z

Heavy-duty bearings and fan motor

z

Quiet Operation

4. Water Distribution System z

Plastic spray header and branches

z

Large orifice, non-clog nozzles

z

Grommetted for easy maintenance

5. BACount Wet Deck Surface z

Plastic material

z

Impervious to rot, decay and biological attack

z

Self extinguishing

z

High temperature wet deck option

6. Strainer z

Anti-vortex design to prevent air entrainment

7. Access Door z

Circular access door

8. Drift Eliminators z

UV resistant non-corrosive material, impervious to rot, decay and biological attack

z

Three distinct changes in air direction to reduce drift loss significantly

z

Assembled in easy to handle sections, which can be removed for access to the equipment interior

... because temperature matters

Open Cooling Towers

3. Centrifugal Fan(s)

VXT - B 8

Custom Features and Options Construction Options

VXT

z

z

Standard Construction: Steel panels and structural elements are constructed of Z600 heavy-gauge hot-dip galvanized steel protected with the Baltiplus Corrosion Protection on the outside of the unit. Optional BALTIBOND® Corrosion Protection System: The BALTIBOND® Corrosion Protection System, a hybrid polymer coating used to extend equipment life, is applied before assembly to all hot-dip galvanized steel components of the unit.

Unit with Stainless Steel Option

z

Optional Stainless Steel Construction: Steel panels and structural elements are constructed of stainless steel either type 304 or 316.

z

Optional Water-Contact Stainless Steel Cold Water Basin: A cost-effective alternative to an all stainless steel unit. The critical components in the cold water basin and the cold water basin itself are provided in stainless steel. The remaining components are protected with the BALTIBOND® Corrosion Protection System.

Note: See section Technical Resources, Material of Construction for more details on the materials described above.

Fan Drive System The fan drive system provides the cooling air necessary to reject heat from the system to the atmosphere. Centrifugal fans, forwardly curved, are driven by matched V-belts with taper lock sheaves.

The Baltiguard® Drive System The BALTIGUARD® Drive System consists of two standard single-speed fan motors and drive assemblies. One drive assembly is sized for full speed and load, and the other is sized for approximately 2/3 speed and consumes only 1/3 of the design kilowatt power. This configuration allows the system to be operated like a two-speed motor, but with the reserve capacity of a standby motor in the event of failure. As a minimum, approximately 70% capacity will be available from the low kilowatt motor, even on a design wet-bulb day. Controls and wiring are the same, as those Baltiguard® Drive System required for a two-speed, two-winding motor. Significant energy savings are achieved when operating at low speed during periods of reduced load and/or low wet-bulb temperatures.

Baltimore Aircoil

VXT - B 9

Low Sound Operation

Note: For more information, please refer to the section “Technical Resources, Sound Reduction Options”.

Units with Intake and Discharge Sound Attenuation

Remote Sump Execution

The use of an auxiliary sump within a heated space is the most satisfactory way to protect sump water from freezing. When the circulating pump is shut off, all the water in the water distribution, in suspension and in the sump will drain freely to the auxiliary sump. Note: For detailed information on the calculation of the remote sump tank, please refer to the section "Technical Resources, Selection of Remote Sump Tank".

High Temperature Wet Deck If operation above 55°C is anticipated, an optional high temperature wet deck material is available which increases the maximum allowable entering water temperature to 65°C.

... because temperature matters

Open Cooling Towers

The low sound levels generated by BAC Products with centrifugal fans make them suitable for most installations. For situations when one direction is particularly sound sensitive, the unit can be oriented so that the side opposite the air inlet faces the sound-sensitive direction. Units with centrifugal fans are also available with factory designed, tested and rated sound attenuation for both the air inlet and discharge.

VXT - B 10

Accessories Ladder, Safety Cage and Handrails

VXT

In the event the owner requires easy access to the top of the unit, the unit can be furnished with ladders extending from the base of the unit to the top, as well as safety cages, and handrail packages. Note: When these access options are employed, the unit must be equipped with steel drift eliminators.

Basin Heaters Units exposed to below freezing ambient temperatures require protection to prevent freezing of the water in the cold water basin when Ladder and Safety Cage, Handrails around top of unit the unit is idle. Factory-installed heaters, which maintain the water temperature at 4°C, are a simple and inexpensive way of providing such protection. The heater package includes the heaters, a thermostat and a low level cut out switch to protect the heaters if the water level is too low. Standard electric heaters are selected for -18°C ambient temperature.

Model No. VXT

Heater -18 °C (kW)

VXT 10-25

1 x 1,5

VXT 30-55

1 x 1,5

VXT 65-85

1 x 2,5

VXT 95-135

1x3

VXT 150-185

1x4

VXT N215-N265

1x6

VXT N310-N395

2x4

VXT N430-N535

2x6

VXT C215-C265

1x6

VXT C310-C395

2x4

VXT C430-C535

2x6

VXT S220-S320

1x6

VXT S345-S470

2x4

VXT S530-S640

2x6

VXT S690-S940

4x4

VXT 315-400

1x6

VXT 470-600

2x5

VXT 630-800

2x6

VXT 870-1200

4x5

Baltimore Aircoil

VXT - B 11

Electric Water Level Control Package The electric water level control replaces the standard mechanical make-up valve when a more precise water level control is required. This package consists of a float switch mounted in the basin and a solenoid activated valve in the makeup water line. The valve is slow closing to minimize water hammer.

Extended Lubrication Lines Extended lubrication lines with grease fittings are available for lubrication of the fan shaft bearings.

Capacity Control Dampers Modulating capacity control dampers are available to provide better leaving water temperature control than can be obtained from fan cycling alone. Fan discharge dampers consist of a single airfoil type damper blade located in the discharge of each fan housing. A standard electrical control package for dampers is available from BAC.

Extended Lubrication Lines

Solid Bottom Panels Factory-installed bottom panels are required when intake air is ducted to the unit.

Discharge Hoods Discharge hoods reduce the risk of re-circulation in tight enclosures by increasing discharge air velocity, and can be used to elevate the unit discharge above adjacent walls to comply with layout guidelines.

Basin Sweeper Piping Basin sweeper piping provides an effective method of preventing sediment from collecting in the cold water basin of the unit. A complete piping system, including nozzles, is provided in the unit basin for connection to side stream filtration equipment. Note: For more information, please refer to the section "Technical Resources, Filtration".

Basin Sweeper Piping

... because temperature matters

Open Cooling Towers

Electric Water Level Control Package

VXT - B 12

Engineering Data REMARK: Do not use for construction. Refer to factory certified dimensions & weights. This brochure includes data current at time of publication, which should be reconfirmed at the time of purchase. In the interest of product improvement, specifications, weights and dimensions are subject to change without notice. Up-to-date engineering data and more can be found at www.BaltimoreAircoil.com.

VXT

VXT 10 - 185

1. Drain ND 50; 2. Water Outlet; 3. Overflow ND50 (Overflow VXT 150 – 185: ND80); 4. Make Up ND25; 5.Water Inlet; 6.Access Door.

On models VXT-10 to VXT-135 sufficient space must be provided on the back of the unit for entry to access doors located on side opposite air entry side.

Model VXT

Operating Shipping Weight Weight (kg) (kg)

Heaviest Section (kg)

H (mm)

L (mm)

W (mm)

Air Flow (m3/s)

Fan Motor Fluid Inlet Fluid Outlet Make Up (kW) ND (mm) ND (mm) ND (mm)

VXT 010 VXT 015 VXT 020 VXT 025

405 410 425 435

325 330 350 360

325* 330* 350* 360*

2036 2036 2036 2036

914 914 914 914

1207 1207 1207 1207

1,79 1,94 2,19 2,50

(1x) 0,75 (1x) 1,1 (1x) 1,5 (1x) 2,2

(1x) 80 (1x) 80 (1x) 80 (1x) 80

(1x) 80 (1x) 80 (1x) 80 (1x) 80

25 25 25 25

VXT 030 VXT 040 VXT 045 VXT 055

655 685 695 780

490 520 530 615

490* 520* 530* 440

2036 2036 2036 2506

1829 1829 1829 1829

1207 1207 1207 1207

3,74 4,48 4,97 5,16

(1x) 1,5 (1x) 2,2 (1x) 4,0 (1x) 5,5

(1x) 80 (1x) 80 (1x) 80 (1x) 80

(1x) 80 (1x) 80 (1x) 80 (1x) 80

25 25 25 25

VXT 065 VXT 070 VXT 075 VXT 085

1050 1075 1135 1140

715 740 805 810

715* 740* 540 540

2036 2220 2506 2506

2737 2737 2737 2737

1207 1207 1207 1207

7,22 8,12 8,02 8,83

(1x) 5,5 (1x) 5,5 (1x) 5,5 (1x) 7,5

(1x) 100 (1x) 100 (1x) 100 (1x) 100

(1x) 100 (1x) 100 (1x) 100 (1x) 100

25 25 25 25

VXT 095 VXT 105 VXT 120 VXT 135

1255 1445 1475 1665

890 1080 1110 1300

890* 575 605 700

2036 2675 2675 3350

3658 3658 3658 3658

1207 1207 1207 1207

11,04 10,90 12,58 12,46

(1x) 7,5 (1x) 7,5 (1x) 11 (1x) 11

(1x) 100 (1x) 100 (1x) 100 (1x) 100

(1x) 100 (1x) 100 (1x) 100 (1x) 100

25 25 25 25

VXT 150 VXT 165 VXT 185

2215 2360 2565

1590 1740 1940

915 915 980**

3128 3585 4042

3645 3645 3645

1438 1438 1438

15,79 15,53 16,94

(1x) 15 (1x) 15 (1x) 18,5

(1x) 150 (1x) 150 (1x) 150

(1x) 150 (1x) 150 (1x) 150

25 25 25

* Units ship in one piece, ** Casing is heaviest section

Baltimore Aircoil

VXT - B 13

VXT N215 - N535

Model VXT

Operating Weight (kg)

Shipping Weight (kg)

Heaviest Section (kg)

VXT N215 VXT N240 VXT N265

3640 3850 4080

2100 2310 2540

1395 1395 1435

3112 3569 4026

3550 3550 3550

2397 2397 2397

23,49 23,33 24,26

(1x) 22 (1x) 22 (1x) 30

(1x) 150 (1x) 150 (1x) 150

(1x) 200 (1x) 200 (1x) 200

50 50 50

VXT N310 VXT N345 VXT N370 VXT N395

5300 5580 5860 5890

3060 3340 3620 3650

1875 1875 1875 1895

3112 3569 4026 4026

5385 5385 5385 5385

2397 2397 2397 2397

34,12 33,82 33,60 36,15

(1x) 30 (1x) 30 (1x) 30 (1x) 37

(1x) 200 (1x) 200 (1x) 200 (1x) 200

(1x) 200 (1x) 200 (1x) 200 (1x) 200

50 50 50 50

VXT N430 VXT N480 VXT N510 VXT N535

7330 7730 8110 8200

4190 4590 4980 5060

2758 2758 2758 2839

3112 3569 4026 4026

7226 7226 7226 7226

2397 2397 2397 2397

46,98 46,65 46,44 48,94

(2x) 22 (2x) 22 (2x) 22 (2x) 30

(2x) 150 (2x) 150 (2x) 150 (2x) 150

(1x) 250 (1x) 250 (1x) 250 (1x) 250

50 50 50 50

H L W Air Flow Fan Motor Fluid Inlet Fluid Outlet Make Up (mm) (mm) (mm) (m3/s) (kW) ND (mm) ND (mm) ND (mm)

... because temperature matters

Open Cooling Towers

1. Drain ND 50; 2. Water Outlet; 3. Overflow ND 80; 4. Make Up ND50; 5.Water Inlet; 6.Access Door.

VXT - B 14

VXT

VXT C215 - C535

1. Drain ND 50; 2. Water Outlet; 3. Overflow ND 80; 4. Make Up ND50; 5. Water Inlet; 6. Access Door

Model VXT-C

Operating Weight (kg)

Shipping Weight (kg)

Heaviest Section (kg)

H (mm)

L (mm)

W (mm)

Air Flow (m3/s)

Fan Motor (kW)

Fluid Inlet ND (mm)

Fluid Outlet ND (mm)

Make Up ND (mm)

VXT C215 VXT C240 VXT C265

4035 4225 4420

2335 2535 2750

1620 1620 1645

3112 3569 4026

3550 3550 3550

2245 2245 2245

23,49 23,33 24,26

(1x) 22 (1x) 22 (1x) 30

(1x) 150 (1x) 150 (1x) 150

(1x) 200 (1x) 200 (1x) 200

50 50 50

VXT C310 VXT C345 VXT C370 VXT C395

5960 6230 6490 6615

3435 3725 4010 4090

2260 2260 2260 2345

3112 3569 4026 4026

5385 5385 5385 5385

2245 2245 2245 2245

34,12 33,82 33,60 36,15

(1x) 30 (1x) 30 (1x) 30 (1x) 37

(1x) 200 (1x) 200 (1x) 200 (1x) 200

(1x) 200 (1x) 200 (1x) 200 (1x) 200

50 50 50 50

VXT C430 VXT C480 VXT C510 VXT C535

8120 8520 8900 8980

4650 5050 5480 5560

1620 1620 1620 1645

3112 3569 4026 4026

7226 7226 7226 7226

2245 2245 2245 2245

46,98 46,65 46,44 48,94

(2x) 22 (2x) 22 (2x) 22 (2x) 30

(2x) 150 (2x) 150 (2x) 150 (2x) 150

(1x) 250 (1x) 250 (1x) 250 (1x) 250

50 50 50 50

Baltimore Aircoil

VXT - B 15

VXT S220 - S940

Model VXT-S

Operating Weight (kg)

Shipping Weight (kg)

Heaviest Section (kg)

H (mm)

L (mm)

W (mm)

Air Flow (m3/s)

Fan Motor (kW)

Fluid Inlet ND (mm)

Fluid Outlet ND (mm)

Make Up ND (mm)

VXT S220 VXT S240 VXT S265 VXT S300 VXT S320

4120 4140 4170 4400 4760

2380 2400 2430 2660 3020

1450 1470 1500 1500 1540

3479 3479 3479 4012 4437

3550 3550 3550 3550 3550

2397 2397 2397 2397 2397

24,8 26,3 29,2 29,0 29,1

(1x) 18,5 (1x) 22 (1x) 30 (1x) 30 (1x) 37

(1x) 200 (1x) 200 (1x) 200 (1x) 200 (1x) 200

(1x) 200 (1x) 200 (1x) 200 (1x) 200 (1x) 200

50 50 50 50 50

VXT S345 VXT S370 VXT S415 VXT S445 VXT S470

6030 6070 6430 6880 6930

3380 3420 3770 4220 4270

2050 2090 2090 2130 2140

3479 3479 4012 4437 4437

5385 5385 5385 5385 5385

2397 2397 2397 2397 2397

38,2 41,0 40,6 40,4 43,2

(1x) 30 (1x) 37 (1x) 37 (1x) 37 (1x) 45

(1x) 200 (1x) 200 (1x) 200 (1x) 200 (1x) 200

(1x) 200 (1x) 200 (1x) 200 (1x) 200 (1x) 200

50 50 50 50 50

VXT S530 VXT S600 VXT S640

8390 8860 9570

4850 5310 6030

2990 2990 3070

3479 4012 4437

7226 7226 7226

2397 2397 2397

58,4 58,0 58,2

(2x) 30 (2x) 30 (2x) 37

(2x) 200 (2x) 200 (2x) 200

(1x) 250 (1x) 250 (1x) 250

50 50 50

VXT S690 VXT S740 VXT S830 VXT S890 VXT S940

12110 12190 12910 13810 13910

6750 6830 7530 8430 8530

4090 4170 4170 4260 4270

3479 3479 4012 4437 4437

10903 10903 10903 10903 10903

2397 2397 2397 2397 2397

76,4 82,0 81,2 80,8 86,4

(2x) 30 (2x) 37 (2x) 37 (2x) 37 (2x) 45

(2x) 200 (2x) 200 (2x) 200 (2x) 200 (2x) 200

(2x) 200 (2x) 200 (2x) 200 (2x) 200 (2x) 200

50 50 50 50 50

... because temperature matters

Open Cooling Towers

1. Drain ND 50; 2. Water Outlet; 3. Overflow ND 80; 4. Make Up ND50; 5. Water Inlet; 6. Access Door

VXT - B 16

VXT

VXT 315 - 1200

1. Drain ND50; 2. Water Outlet; 3. Overflow ND 80; 4. Make Up ND50 and 870 - 1200: ND80; 5.Water Inlet; 6.Access Door.

Model VXT

Operating Weight (kg)

Shipping Weight (kg)

Heaviest Section (kg)

H (mm)

L (mm)

W (mm)

VXT 315 VXT 350 VXT 375 VXT 400

4905 5195 5505 5535

2960 3260 3560 3590

1945 1945 1945 1970

4030 4487 4944 4944

3550 3550 3550 3550

3000 3000 3000 3000

34,55 34,31 34,10 36,62

(1x) 30 (1x) 30 (1x) 30 (1x) 37

(1x) 200 (1x) 200 (1x) 200 (1x) 200

(1x) 200 (1x) 200 (1x) 200 (1x) 200

50 50 50 50

VXT 470 VXT 525 VXT 560 VXT 600

7305 7750 8245 8325

4360 4810 5290 5370

2770 2770 2770 2845

4030 4487 4944 4944

5388 5388 5388 5388

3000 3000 3000 3000

51,82 51,44 50,92 54,93

(2x) 22 (2x) 22 (2x) 22 (2x) 30

(1x) 250 (1x) 250 (1x) 250 (1x) 250

(1x) 250 (1x) 250 (1x) 250 (1x) 250

50 50 50 50

VXT 630 VXT 700 VXT 750 VXT 800

9805 10385 11005 11055

5900 6490 7110 7160

3885 3885 3885 3925

4030 4487 4944 4944

7226 7226 7226 7226

3000 3000 3000 3000

69,09 68,62 68,20 73,25

(2x) 30 (2x) 30 (2x) 30 (2x) 37

(2x) 200 (2x) 200 (2x) 200 (2x) 200

(1x) 300 (1x) 300 (1x) 300 (1x) 300

50 50 50 50

VXT 870 VXT 945 VXT 1050 VXT 1125 VXT 1200

14570 14680 15560 16490 16570

8720 8830 9710 10640 10720

5670 5785 5785 5785 5855

4030 4030 4487 4944 4944

10903 10903 10903 10903 10903

3000 3000 3000 3000 3000

94,37 103,64 102,93 102,30 109,87

(3x) 22 (3x) 30 (3x) 30 (3x) 30 (3x) 37

(3x) 200 (3x) 200 (3x) 200 (3x) 200 (3x) 200

(2x) 250 (2x) 250 (2x) 250 (2x) 250 (2x) 250

80 80 80 80 80

Air Flow Fan Motor Fluid Inlet Fluid Outlet Make Up (m3/s) (kW) ND (mm) ND (mm) ND (mm)

General Notes 1. All connections 100 mm and smaller are MPT. Connections 150 mm and larger are bevelled-for-welding. 2. Fan kW is at 0 Pa ESP. To operate against external static pressure up to 125 Pa, increase each fan motor one size.

3. The drawings show the standard “right hand” arrangement, which has the air inlet side on the right when facing the connection end. “Left hand” arrangement can be furnished by special order. 4. Water outlet, overflow and make-up are always located on the same end of the unit. For units with two water outlet connections an additional overflow connection will be installed on the other end of the unit.

Baltimore Aircoil

VXT - B 17

Sound Attenuation XA + XB Sound Attenuation for VX-Line Cooling Towers

XC Sound Attenuation for VX-Line Cooling Towers

1. Access Door; L1= Intake Attenuator Length; L2= Discharge Attenuator Length; W & H= unit dimensions (see Engineering Data)

... because temperature matters

Open Cooling Towers

1. Access Door; L1= Intake Attenuator Length; L2= Discharge Attenuator Length; W & H= unit dimensions (see Engineering Data).

VXT - B 18

Model No. VXT

Unit + # Access Atten. # doors (3) pieces XA, XB, XC shipped

VXT

XA, XB, Disch. Int. XC Att. Att.

Dimensions (mm) W2

H1

XA, XB

XC

W1

Weights (kg) L1

L2

XA, XB, XC

Intake XA

XB

Discharge XC

Solid Bottom

Total

XA

XB

XC

XA

XB

XC

10 - 25

3

1

2

2352

N.A.

1090 1030

890

900

110

130 N.A.

30

130

150

N.A.

270

310

N.A.

30 - 55

3(1)

1

2

2352

N.A.

1090 1030 1800

1815

175

220 N.A.

50

175

220

N.A.

400

490

N.A.

65 - 85

3

(1)

1

2

2352

N.A.

1090 1030 2710

2730

230

300 N.A.

70

280

350

N.A.

580

720

N.A.

95 - 135

4(2)

1

2

2352

N.A.

1090 1030 3635

3645

300

370

830

100

360

420

N.A.

760

890

N.A.

150 - 185

4

1

2

2583

3728

1600 1420 3635

3645

380

480 1080

120

440

520

1070 940 1120 2270

N215 – N265

4

1

2

3542

4687

2070 1955 3510

3645

500

630 1420

190

530

650

1330 1220 1470 2940

660

970

1980 1720 2130 4250

N310 – N395

4

2

2

3542

4687

2070 1955 5365

5480

860 1970

300

760

N430 - N535

7

2

2

3542

4687

2070 1955 7185

7320 1000 1260 2840

380

1060 1300 2660 2440 2940 5880

C215 - C265

4

1

2

3390

4687

2070 1955 3510

3645

500

630 1420

190

530

650

1330 1220 1470 2940

C310 – C395

4

2

2

3390

4687

2070 1955 5365

5480

660

860 1970

300

760

970

1980 1720 2130 4250

C430 – C535

7

2

2

3390

4535

2070 1955 7185

7320 1000 1260 2840

380

1060 1300 2660 2440 2940 5880

S220 – S320

4

1

2

3542

4687

2070 2365 3550

3645

500

630 1420

190

660

S345 – S470

4

2

2

3542

4687

2070 2365 5385

5480

660

860 1970

300

830 1090 2240 1790 2250 4510

S530 – S640

7

2

2

3542

4687

2070 2365 7226

7322 1000 1260 2840

380

1320 1600 3280 2700 3240 6500

S690 – S940

7

4

2

3542

4687

2070 2365 10903 10998 1320 1720 3940

600

1660 2180 4480 3580 4500 9020

315 - 400

4

2

2

4145

5290

2560 2965 3510

3645

560

710 1620

230

710

470 - 600

4

2

2

4145

5290

2560 2965 5365

5480

730

980 2240

350

900 1210 2490 1980 2540 5080

630 - 800

7

4

2

4145

5290

2560 2965 7185

7320 1120 1420 3240

460

1420 1760 3640 3000 3640 7340

870 - 1200

10

3

3

4145

5290

2560 2965 10865 10995 1680 2130 4860

690

2130 2640 5460 4500 5460 11010

(1)

VXT-55 + attenuation is shipped in 4 pieces

(1)

VXT-75 and VXT 85 + attenuation is shipped in 4 pieces

(2)

VXT-95 + attenuation is shipped in 3 pieces

(3)

Intake Attenuator: Access opening is 775 mm high, 406 mm wide and is located at each end of the unit.

(3)

800

880

1640 1350 1620 3250

1820 1500 1820 3670

Discharge Attenuator : Access opening is 400 mm high, 1080 mm wide and is located at blank off side of the unit (Access door of VXT 10-25 has 650 mm width)

Baltimore Aircoil

VXT - B 19

Structural Support REMARK: Do not use for construction. Refer to factory certified dimensions & weights. This brochure includes data current at time of publication, which should be reconfirmed at the time of purchase. In the interest of product improvement, specifications, weights and dimensions are subject to change without notice. Up-to-date engineering data and more can be found at www.BaltimoreAircoil.com. The recommended support arrangement for units consists of parallel I-beams running the full length of the unit, spaced as shown in the following drawing. Besides providing adequate support, the steel also serves to raise the unit above any solid foundation to ensure access to the bottom of the unit. To support units in an alternate steel support arrangement, consult your BAC Balticare Representative.

Open Cooling Towers

Units without Sound Attenuation

1. Outline of Unit; 2. Mounting Holes Ø 22 mm; 3. Unit; 4. Air Intake.

Model

VXT 10-25

A Unit Length (mm)

B Unit Width (mm)

C Center dis. Length (mm)

D Center dis. Width (mm)

E (mm)

F (mm)

G (mm)

H (mm)

X Max. Deflection (mm)

Mounting Holes

914

1207

750

1153

-

-

-

-

2

4

VXT 30-55

1829

1207

1664

1153

-

-

-

-

5

4

VXT 65-84

2737

1207

2572

1153

-

-

-

-

8

4

VXT 95-135

3658

1207

3492

1153

-

-

-

-

10

4

VXT 150-185

3645

1438

3492

1378

-

-

-

-

10

4

VXT N215-N265

3550

2397

3238

2327

-

-

-

-

10

4

VXT 315-400

3550

3000

3238

2934

-

-

-

-

10

4

VXT N310-N395

5388

2397

5074

2327

2496

102

-

-

13

8

VXT 470-600

5388

3000

5074

2934

2496

102

-

-

13

8

VXT N430-N535

7226

2397

6914

2327

3238

438

-

-

13

8

VXT C215–C265

3550

2245

3238

2175

-

-

-

-

10

4

VXT C310-C395

5385

2245

5074

2175

2486

102

-

-

13

8

... because temperature matters

VXT - B 20

A Unit Length (mm)

B Unit Width (mm)

C Center dis. Length (mm)

D Center dis. Width (mm)

E (mm)

F (mm)

G (mm)

H (mm)

X Max. Deflection (mm)

Mounting Holes

VXT C430-C535

7226

2246

6914

2175

3238

438

-

-

13

8

VXT S220-S320

3550

2397

3238

2327

-

-

-

-

10

4

VXT S345-S470

5385

2397

5074

2327

2486

102

-

-

13

8

VXT

Model

VXT S530-S640

7226

2397

6914

2327

3238

438

-

-

13

8

VXT S690-S940

10903

2397

10586

2327

2486

102

438

-

13

16

VXT 630-800

7226

3000

6914

2934

3238

438

-

-

13

8

VXT 870-1200

10903

3000

10590

2934

3238

438

3238

438

13

12

Units with Sound Attenuation

1. Outline of Unit; 2. Mounting Holes Ø 22 mm; 3. Outline of attenuator (optional XA or XB); 4. Support Channel attached to optional XA or XB attenuator; 5. (3 + 5) Outline of Attenuator (optional XC); 6. (4 + 6) Support Channels attached to optional XC attenuator; 7. Unit; 8. Sound Attenuation (Type XA, XB or XC); 9. Air Intake.

Baltimore Aircoil

VXT - B 21

Notes: 1. The recommended support arrangement for VX units consists of parallel I-beams extending the full length of the unit. Supports and anchor bolts are to be designed and furnished by others. 2. All supporting beams are to be flush and level at top and must be oriented relative to gage line as shown.

4. All mounting holes have a diameter of 22 mm at the locations shown. 5. If vibration isolators are used, a rail or channel must be provided between the unit (and optional attenuator) and the isolators to provide continuous unit support. Additionally the support beams must be designed to accommodate the overall length and mounting hole location of the isolators that may differ from those of the unit. Refer to vibration isolator drawings for these data.

... because temperature matters

Open Cooling Towers

3. Recommended design loads for each unit support beam should be 70% of the total unit operating weight applied as a uniform load to each of the unit beams. The support beam(s) for the optional intake attenuator(s) needs to carry attenuator only, uniform load of 250 kg/m. Beams should be designed in accordance with

standard structural practice. For the maximum allowable deflection of beams under the unit refer to above table.

VXT - B 22

Engineering Specifications

VXT

1.0 Cooling Tower 1.1 General: Furnish and install _____ factory-assembled, forceddraft, centrifugal fan, counter flow cooling tower(s) with vertical air discharge, conforming in all aspects to the specifications, schedules and as shown on the plans. Overall dimensions shall not exceed approximately _____ mm long x ______ mm wide x _____ mm high. The total connected fan power shall not exceed _____ kW. The cooling tower(s) shall be Baltimore Aircoil Model ____________. 1.2 Thermal Capacity: The cooling tower(s) shall be warranted by the manufacturer to cool _____ l/s of water from ______ °C to _____C at _____°C entering wet-bulb temperature. 1.3 Corrosion Resistant Construction (standard): Unless otherwise noted in this specification, all steel panels and structural members shall be constructed of heavy-gauge Z600 metric hot-dip galvanized steel with all edges given a protective coating of zinc-rich compound and the exterior protected with the BALTIPLUS Protection. (Alternate 1.3) Corrosion Resistant Construction (optional): Unless otherwise noted in this specification, all steel panels and structural members shall be protected with the BALTIBOND®

Corrosion Protection System. The system shall consist of Z600 metric hot-dip galvanized steel prepared in a four-step (clean, pre-treat, rinse, dry) process with an electrostatically sprayed, thermosetting, hybrid polymer fuse-bonded to the substrate during a thermally activated curing stage and monitored by a 23-step quality assurance program. (Alternate 1.3) Corrosion Resistant Construction (optional): Unless otherwise noted in this specification, all steel panels and structural members shall be constructed of Type 304 or 316 stainless steel and assembled with stainless steel nut and bolt fasteners. 1.4 Quality Assurance: The cooling tower manufacturer shall have a Management System certified by an accredited registrar as complying with the requirements of ISO-9001:2000 to ensure consistent quality of products and services. 1.5 Warranty: The manufacturer’s standard equipment warranty shall be for a period of not less than one year from date of startup or eighteen months from date of shipment, whichever occurs first.

2.0 Construction Details 2.1 Structure (VX-Line models): The cooling tower shall be constructed of heavy-gauge steel utilizing double-brake flanges for maximum strength and rigidity and reliable sealing of watertight joints. The heat transfer section shall be removable from the pan/fan section to facilitate shipping and handling. The fan(s) and fan drive system, including the fan motor, shall be factory mounted and aligned and located in the dry entering air stream to ensure reliable operation and ease of maintenance. 2.2 Heat Transfer Section: The heat transfer sections(s) shall consist of a wet deck surface, spray water distribution system and drift eliminators arranged for optimal thermal performance with minimal drift. 2.3 Wet Deck Surface: The wet deck surface shall be formed from self-extinguishing plastic material and shall be impervious to rot, decay, and fungus or biological attack. The wet deck surface shall be manufactured and performance tested by the cooling tower manufacturer to assure single source responsibility and control of the final product. 2.4 Water Distribution System: Water shall be distributed evenly over the wet deck surface by a water distribution system consisting of a header and spray branches of plastic pipe with large orifice, nonclog plastic distribution nozzles. The branches and spray nozzles shall be held in place by snap-in rubber grommets, allowing quick

removal of individual nozzles or complete branches for cleaning or flushing. 2.5 Cold Water Basin: The cold water basin shall be provided with large area lift out strainers with perforated openings sized smaller than the water distribution system nozzles and an anti-vortexing device to prevent air entrainment. The strainer and anti-vortexing device shall be constructed of the same material as the basin to prevent dissimilar metal corrosion. Standard basin accessories shall include a brass make-up valve with large diameter polystyrene filled plastic float for easy adjustment of the operating water level. (Alternate2.5) Cold Water Basin: The cold water basin shall be constructed of heavy-gauge Type 304 or 316 stainless steel panels and structural members up to the heat transfer section/basin joint. The basin shall be provided with large area lift out strainers with perforated openings sized smaller than the water distribution system nozzles and an anti-vortexing device to prevent air entrainment. The strainer and anti-vortexing device shall be constructed of the same material as the basin to prevent dissimilar metal corrosion. Standard basin accessories shall include a brass make-up valve with large diameter polystyrene filled plastic float for easy adjustment of the operating water level.

3.0 Mechanical Equipment 3.1 Fan(s): Fan(s) shall be dynamically balanced, forwardly curved, centrifugal type selected to provide optimum thermal performance with minimal sound levels. Fan housings shall have curved inlet rings for efficient air entry and four-sided rectangular discharge cowls shall extend into the basin to increase fan efficiency and prevent water from splashing into the fans. 3.2 Bearings: Fan(s) and shaft(s) shall be supported by heavy-duty, self-aligning, relubricatable bearings with cast iron housings, designed for a minimum L10 life of 40 000 hours (280 000 Hr. Average. Life). 3.3 Fan Drive: The fan(s) shall be driven by matched V-belts with taper lock sheaves. Motor shall be located on a heavy-duty motor

base, adjustable by a single threaded bolt-and-nut arrangement. Removable steel screens or panels shall protect the fan drive and all moving parts. 3.4 Fan Motor: Furnish _____ kW, ______ RPM Totally Enclosed, Fan Cooled (TEFC), squirrel cage, ball bearing type fan motors suitable for outdoor service. Motor(s) shall be suitable for ________ volt, ___ hertz, and __ phase electrical service. 3.5 BALTIGUARD® Fan System (optional): Two-single speed fan motors, one sized for full speed and load, the other sized for 2/3 speed and approximately 1/3 of full load kW shall be provided in each cell for capacity control and stand-by protection from drive or motor failure. Two-speed motor(s) are not an acceptable alternative.

Baltimore Aircoil

VXT - B 23

4.0 Drift Eliminators 4.1 Drift Eliminators: Eliminators shall be constructed of specially formulated plastic material and be removable in easily handled sections. They shall have a minimum of three changes in air direction.

5.0 Access 5.1 Basin Access: Circular access doors shall be provided for easy access to the make-up water assembly and suction strainer for routine maintenance.

6.1 Sound Level: To maintain the quality of the local environment, the maximum sound pressure levels (dB) measured 15 m from the

Location

63

125

250

500

cooling tower operating at full fan speed shall not exceed the sound levels detailed below.

1000

2000

4000

Discharge Air Inlet End Back

... because temperature matters

8000

dB(A)

Open Cooling Towers

6.0 Sound

CCCT - C 1

Closed Circuit Cooling Towers Overview

General Information ................................................................................. C2 Principle of Operation .............................................................................. C2 Configuration ............................................................................................. C2 Fan System ................................................................................................. C3 Capacity Range .......................................................................................... C3 Maximum Entering Fluid Temperature .................................................. C4 Typical Applications .................................................................................. C4 Product Line Overview Table .................................................................. C4 Advantages of Closed Circuit Cooling Towers ....................................... C6 Engineering Considerations ..................................................................... C9

Closed Circuit Cooling Towers

Product Group Detail

CCCT - C 2

General Information Closed circuit cooling towers provide evaporative cooling for many types of systems, and the specific application will largely determine which BAC Closed Circuit Cooling Tower is best suited for a project. The Product Line Overview Table is intended as a general guide. Specialized assistance is available through your local BAC Balticare Representative.

Overview

Principle of Operation Closed circuit cooling towers operate in a manner similar to open cooling towers, except that the heat load to be rejected is transferred from the process fluid (the fluid being cooled) to the ambient air through a heat exchange coil. The coil serves to isolate the process fluid from the outside air, keeping it clean and contamination free in a closed loop. This creates two separate fluid circuits: (1) an external circuit, in which spray water circulates over the coil and mixes with the outside air, and (2) an internal circuit, in which the process fluid circulates inside the coil. During operation, heat is transferred from the internal circuit, through the coil to the spray water, and then to the atmosphere as a portion of the water evaporates.

Configuration BAC manufactures two types of closed circuit cooling towers: combined flow and counterflow.

Combined Flow Combined flow is the use of both a heat exchange coil and wet deck surface for heat transfer in a closed circuit cooling tower. The addition of wet deck surface to the traditional closed circuit cooling tower design reduces evaporation in the coil section, reducing the potential for scaling and fouling. BAC’s combined flow closed circuit cooling towers utilize parallel flow of air and spray water over the coil, and crossflow air/water flow through the wet deck surface. In parallel flow, air and water flow over the coil in the same direction. The process fluid travels from the bottom to the top of the coil, increasing efficiency by bringing the coldest spray water and air in contact with the process fluid at its coldest temperature.

Combined Flow: Parallel flow of air and water over the coil in counterflow with the fluid inside the coil

Baltimore Aircoil

Combined Flow: Crossflow configuration over the wet deck

CCCT - C 3

Counterflow In a counterflow closed circuit cooling tower design, the flow of the air is in the opposite direction of the spray water. In BAC’s counterflow closed circuit cooling towers, air travels vertically up through the unit while the spray water travels vertically down over the coil.

Fan System

Centrifugal Fans

Axial Fans

Induced Draft The rotating air handling components of induced draft equipment are mounted in the top deck of the unit, minimizing the impact of fan noise on near-by neighbors and providing maximum protection from fan icing with units operating in sub-freezing conditions. The air being drawn through the unit hereby discharges over the inducing fan. The use of corrosion resistant materials ensures long life and minimizes maintenance requirements for the air handling components. Forced Draft Rotating air-handling components are located on the air inlet face at the base of forced draft equipment whereby fresh air is blown through the unit. This base fan position facilitates easy access for routine maintenance and service. Additionally, location of these components in the dry entering air stream extends component life by isolating them from the corrosive saturated discharge air.

Capacity Range In the Product Line Overview Table, product capacities are called out in terms of a flow rate. This refers to the fluid flow rate that the unit can cool from a 30ºC entering water temperature to 25°C leaving water temperature at a 21ºC entering ambient wet-bulb temperature. All capacities shown are for a single cell; multiple cell units can be applied to achieve larger capacities.

... because temperature matters

Closed Circuit Cooling Towers

The flow of air through most factory assembled evaporative cooling equipment is provided by one or more mechanically driven fans. The fan(s) may be axial or centrifugal, each type having its own Counterflow Configuration distinct advantages. Axial fan units require approximately half the fan motor kilowatt of comparably sized centrifugal fan units, offering significant life-cycle cost savings. Centrifugal fan units are capable of overcoming reasonable amounts of external static pressure (≤125 Pa), making them suitable for both indoor and outdoor installations. Centrifugal fans are also inherently quieter than axial fans, although the difference is minimal and can often be overcome through the application of optional low sound fans and/or sound attenuation on axial fan units. Fans can be applied in an induced draft or a forced draft configuration.

CCCT - C 4

Maximum Entering Fluid Temperature All BAC Closed Circuit Cooling Towers are capable of withstanding entering fluid temperatures as high as 82ºC.

Typical Applications

Overview

A list of typical applications is provided in the Product Line Overview Table for your reference.

Product Line Overview Table

VXI

2 11

VFL

7

10 11 1

8

4

6

1

3

7

3

8

Principle of Operation

2

10

9

6

4 9

Configuration

Counterflow

Counterflow

Fan System

Centrifugal Fan, Forced Draft

Centrifugal Fan, Forced Draft

Capacity Range (Single Cell)

1,5 tot 200 l/s

1 to 65 l/s

Maximum Entering Fluid Temperature

82°C

82°C

Typical Applications

Small to medium HVAC & industrial applications such as water source heat pump loops and air compressor cooling Indoor installations High temperature applications Tight enclosures & installations requiring a single air inlet Extremely sound sensitive applications

Small to medium HVAC & industrial applications Installations with extremely low height requirements Indoor installations High temperature industrial applications Extremely sound sensitive applications

1. Air In; 2. Air Out; 3. Fluid In; 4. Fluid Out; 5. Wet Deck Surface; 6. Cold Water Basin; 7. Water Distribution System; 8. Coil; 9. Spray Water Pump; 10. Eliminators; 11. Optional Extended Surface.

HFL, HXI and DFC water saving and hybrid wet-dry closed circuit products are available to meet specific design requirements. Refer to the "Water Saving Products" section for more details on these products.

Baltimore Aircoil

CCCT - C 5

FXV - Single Air Inlet Models

2

FXV-D Dual Air Inlet Models

1

2

7 2

8

10

2

7 4

8

3

10

3

5

5 1 6

1

1

4

9

1

4

2

10

3

10 2 6

2 9

1

Combined flow

Combined flow

Axial Fan, Induced Draft

Axial Fan, Induced Draft

3 to 149 l/s

200 to 300 l/s

82°C

82°C

Small to medium HVAC & industrial applications such as water source heat pump loops and air compressor cooling Tight enclosures & installations requiring a single air inlet Unit replacements

Medium to large HVAC & industrial applications such as electric arc furnaces and pharmaceutical plants

... because temperature matters

Closed Circuit Cooling Towers

S1500

CCCT - C 6

Overview

Advantages of Closed Circuit Cooling Towers Open cooling towers expose process cooling water to the atmosphere, typically as part of a chiller system loop (see Figure 1). These open towers use an efficient, simple, and economical design. All components in an open system must be compatible with the oxygen introduced via the cooling tower. Closed circuit cooling towers completely isolate process cooling fluid from the atmosphere. This is accomplished by combining heat rejection equipment with a heat exchanger in a closed circuit tower (see Figure 2). A closed loop system protects the quality of the process fluid, reduces system maintenance, and provides operational flexibility at a slightly higher initial cost. When deciding which system is best for an application, several factors should be considered.

Figure 1 : Chiller Loop w/Open Tower

Figure 2 : Chiller Loop w/Closed Circuit Tower

Performance If an application must produce full capacity throughout the year, maintaining a clean, reliable system loop is critical. Isolating the process fluid in a closed loop system prevents airborne

Baltimore Aircoil

CCCT - C 7

contaminants from entering and fouling the system. Sustaining optimum performance in an open loop system will require regular maintenance to assure similar efficiency. High efficiency chillers and heat exchangers rely on clean process water to function properly and are significantly impacted by even small amounts of fouling.

Expense

z

Cleaner process fluid results in a cleaner internal surface area, and higher efficiency components in the system (e.g. chiller)

z

Reduced system maintenance costs

z

Reduced water treatment costs for evaporative equipment

z

Operating in ‘free cooling’ mode during the winter to save energy consumption

Maintenance Since the process fluid of a closed loop system is completely isolated from the environment, routine maintenance is only required on the heat rejection equipment itself. The need to shut down the system periodically to clean the heat exchanger is dramatically reduced, if not entirely eliminated. Providing clean process fluid to the system will extend the life of other components in the system (condenser bundles, compressors, etc.).

Water Treatment Maintaining proper process fluid quality in a system may involve several steps, such as chemical treatment, filtration equipment and the addition of clean make-up water. A closed circuit cooling tower can provide the following advantages over an open cooling tower: z

Lower volume of recirculating water to treat

z

Process loop requires minimal treatment

z

During periods of dry operation, the need for make-up water is eliminated

Operational Flexibility Closed circuit cooling towers allow for the following modes of operation not possible with open cooling towers: z

Free cooling operation without the need for an intermediate heat exchanger: Chiller turned off

z

Dry operation: Conserve water and treatment chemicals, prevent icing and eliminate plume

z

Variable pumping: Closed condenser water loop allows for variable speed pumping to conserve energy

... because temperature matters

Closed Circuit Cooling Towers

The initial equipment cost of an open loop system will be less than a comparably sized closed loop system, since the open system does not include the intermediate heat exchanger component. However, the higher first cost of a closed loop system will be paid back during years of operation through the following savings:

CCCT - C 8

Closed Circuit Tower versus Open Tower / Heat Exchanger Sometimes, an open cooling tower is paired with a heat exchanger (see Figure 3) to capture some of the benefits of closed loop cooling. Choosing closed circuit cooling towers over this open tower/ heat exchanger combination may still be a better choice for the following reasons: z

Overview

z

z

z

Total cost: Addition of a heat exchanger (pump, piping, etc.) to the open tower loop brings the initial cost much closer to that of the closed circuit tower system Single piece of equipment: Compact design of the closed circuit tower conserves space in a self-contained package, compared to multiple locations for the tower/heat exchanger arrangement Maintenance: Narrow spacing in heat exchanger (e.g. plate and frame) may trap solids introduced by the open tower, requiring frequent, time consuming cleaning to assure optimum performance Dry operation: Open tower/heat exchanger system cannot be run dry in the winter

These guidelines provide some general information to help decide whether a closed circuit cooling tower is better suited for a particular application than an open tower, with or without a heat exchanger. For additional assistance with a project, please contact your local BAC Balticare Representative.

Figure 3 : Chiller Loop w/Open Tower/Heat Exchanger Combination

Note : BAC offers heat exchanger skids in combination with most of his open cooling tower products. These skids are available for both new installations or to retrofit on existing installations. The heat exchanger skid consists of a plate heat exchanger with pump and interconnecting piping and appendages. The skids are delivered on a heavy duty frame and with steel panel enclosure. Refer to your BAC Balticare representative for more details and selections.

Baltimore Aircoil

CCCT - C 9

Engineering Considerations Location Units must have an adequate supply of fresh air to the air inlet(s). When units are located adjacent to building walls or in enclosures, care must be taken to ensure that the warm, saturated discharge air is not deflected off surrounding walls or enclosures and drawn back to the air inlet(s). Warning: Each unit should be located and positioned to prevent the introduction of the warm discharge air and the associated drift, which may contain chemical or biological contaminants including Legionella, into the ventilation systems of the building on which the unit is located or those of adjacent buildings.

For VL and VX products, bottom screens or solid bottom panels may be desirable or necessary for safety, depending on the location and conditions at the installation site.

Piping and Valves Piping must be sized and installed in accordance with good piping practice. All piping should be supported by pipe hangers or other supports, not by the unit. Some installations may require flow balancing valves (supplied by others) at the coil inlets to balance the flow to individual coils and cells. External shutoff valves on the closed circuit loop (supplied by others) may also be required if the system design necessitates the isolation of individual cells. Although equalizing lines can be used to balance water levels between multi-cell closed circuit cooling towers, the spray water for each cell must be treated separately, and a separate make-up must be provided for each cell. Note that a common remote sump for multi-cell installations can simplify make-up and water treatment – see "Technical Resources, Remote Sump Tank Selection" for details. See the appropriate Operating and Maintenance Instruction Manual for more information on water treatment.

Capacity Control Variable Frequency Drives (VFD) Installations which are to be controlled by Variable Frequency Drives (VFD) require the use of an inverter duty motor as designed IEC 34.1, which recognizes the increased stresses placed on motors by these drive systems. Inverter duty motors must be furnished on VFD applications in order to maintain the motor warranty. Fan motors must be furnished with thermal protection (either PTC sensors or coil thermostats normally open, or normally closed). The motor protection consists of temperature sensitive cutout devices embedded in the motor windings (minimum 3 per motor). The minimum fan motor speed during normal operation should be not below 30% of the speed indicated on the motor nameplate. This corresponds with 15 Hz for a 50 Hz supply and 18 Hz for a 60 Hz supply. BAC offers factory installed motor control packages including VFD drives. Refer to the section "Technical Resources, Motor Controls". Check with your local BAC Balticare representative for availability. Warning: When the fan speed is to be changed from the factory-set speed, including through the use of a variable speed control device, steps must be taken to avoid operating at or near fan speeds that cause a resonance with the unit or its supporting structure. At start-up, the variable frequency drive should be cycled slowly between zero and full speed and any speeds that cause a noticeable resonance in the unit should be “locked out” by the variable speed drive.

Fan Cycling Fan cycling is the simplest method of capacity control. The number of steps of capacity control can be increased using the Baltiguard® Fan System, the independent fan motor option, or two-speed fan motors in conjunction with fan cycling (see the “Custom Features & Options” section of the appropriate product line to determine whether the Baltiguard® Fan System or the independent fan motor option are available; two-speed motors are available for all products). These options provide substantial energy savings when compared to simple fan cycling. Warning: Rapid on-off cycling can cause the fan motor to overheat. It is recommended that controls be set to allow a maximum of 6 on-off cycles per hour.

... because temperature matters

Closed Circuit Cooling Towers

Note: For detailed recommendations on layout, please consult your local BAC Balticare Representative.

CCCT - C 10 Note: Spray water pump cycling should not be used for capacity control. This method of control often results in short cycling of the pump motor as capacity changes substantially with pump cycling. In addition, alternate wetting and drying of the coil promotes scaling of the heat exchanger coil surface.

Capacity Control Dampers (VFL and VXI models only) On centrifugal fan models, modulating capacity control dampers are available to provide close control of the leaving temperature. See Section "Accessories" or contact your local BAC Balticare representative.

Overview

Vibration Cutout Switch Vibration cutout switches are recommended on all axial fan installations. Vibration cutout switches are designed to interrupt power to the fan motor and/or provide an alarm to the operator in the event of excessive vibration. BAC offers both electronic and mechanical vibration cutout switches on all closed circuit cooling towers.

Water Treatment As water evaporates in the unit, the dissolved solids originally present in the water remain in the system. The concentration of these dissolved solids increases rapidly and can cause scale and corrosion. In addition, airborne impurities and biological contaminants, including Legionella, may be introduced into the circulating water. To control all potential contaminants, a water treatment program must be employed. In many cases, a simple bleed-off may be adequate for control of scale and corrosion. However, biological contamination, including Legionella, can be controlled only through the use of biocides. Such treatment should be initiated at system startup, after periods of equipment shutdown, and continued regularly thereafter. Accordingly, it is strongly recommended a biocide treatment be initiated when the unit is first filled with water and continued regularly thereafter. For more information, consult the appropriate Operating and Maintenance Manual. When a water treatment program is employed, it must be compatible with construction materials. Batch feeding of chemicals into the unit is not recommended. If units are constructed with optional corrosion resistant materials, acid treatment may be considered; however, the water quality must be maintained within the guidelines set forth in the Operating and Maintenance Instructions. Note: Unless a common remote sump is utilised, each cell of a multi-cell installation must be treated as a separate entity, even if the cold water basins are equalized.

For complete Water Quality Guidelines, see the appropriate Operating and Maintenance Instruction Manual, available at www.baltimoreaircoil.com. For specific recommendations on water treatment, contact a competent water treatment supplier.

Wet Deck Surface Compatibility (FXV and FXV-D models only) The standard wet deck surface in FXV and FXV-D Closed Circuit Cooling Towers is constructed of a plastic material This wet deck surface is compatible with the water found in most evaporative cooling applications. For applications where the entering fluid temperature exceeds 82°C, contact your local BAC Balticare Representative to confirm that the standard wet deck is acceptable.

Sound Levels Sound rating data are available for all BAC models. When calculating the sound levels generated by a unit, the designer must take into account the effects of the geometry of the tower as well as the distance and direction from the unit to noise-sensitive areas. Whisper Quiet fans and intake and discharge sound attenuation can be supplied on certain models to provide reduced sound characteristics (see the “Custom Features and Options” section of the appropriate product line for details). The Baltiguard® Fan System, two-speed motors, or variable frequency drives can also be used to reduce sound during periods of non-peak thermal loads. For more information on sound and how it relates to evaporative cooling equipment, see Section "Technical Resources, Fundamentals of Sound". For detailed low sound selections, please consult your local BAC Balticare Representative.

Baltimore Aircoil

CCCT - C 11

Winterization

Indoor Installation (applicable to VXI and VFL models only) Many indoor installations require the use of inlet and/or discharge ductwork. Units installed with inlet ductwork must be ordered with solid-bottom panels. Generally, intake ducts are used only on smaller units while the equipment room is used as a plenum for larger units. Discharge ductwork will normally be required to carry the saturated discharge air from the building. Both intake and discharge ductwork must have access doors to allow servicing of the fan assembly, drift eliminators, and water distribution system. All ductwork is supplied and installed by others and should be symmetrical and designed to provide even air distribution across the face of air intakes and discharge openings. Such ductwork may increase the external static pressure on the unit, requiring a larger fan motor to be installed. This external static pressure must be quantified (in Pa) to BAC to allow for suitable fan motor sizing. Warning: The discharge opening must be positioned to prevent the introduction of discharge air into the fresh air intakes serving the unit or the ventilation systems of adjacent buildings.

Note: Axial fan units are not suitable for indoor installations.

Safety Adequate precautions, appropriate for the installation and location of these products, should be taken to safeguard the public from possible injury and the equipment and the premises from damage. Operation, maintenance and repair of this equipment should be undertaken only by personnel qualified to do so. Proper care, procedures and tools must be used in handling, lifting, installing, operating, maintaining, and repairing this equipment to prevent personal injury and/or property damage.

Fluid Compatibility The fluid to be cooled must be compatible with the coil material (standard serpentine are carbon steel, hot-dip galvanized on the outside only). Fluids not compatible with coil materials can lead to corrosion and tube failure. Certain fluids may require occasional pressure cleaning or mechanical cleaning of the inside of coil tubes. In such cases the coil must be designed to provide this capability.

Open / Closed System The standard galvanised steel serpentine and coils are carbon steel, hot-dip galvanised on the outside only, and are intended for application on closed, pressurised systems which are not open to the atmosphere. Stainless steel coils or cleanable coil units (with tubes hot-dip galvanized inside and out) are available to cool corrosive fluids or water and ethylene/propylene glycol solutions in systems open to the atmosphere

Protection Against Coil Freezing At below freezing ambient conditions, the unit can experience heat loss even without the recirculating spray water pump and fans in operation. Without a heat load on the circulating fluid,

... because temperature matters

Closed Circuit Cooling Towers

When a unit is shut down in freezing weather, the basin water must be protected by draining to an indoor auxiliary remote sump tank or by providing supplementary heat to the cold water basin. Supplementary heat can be provided by electric immersion heaters or in some cases, hot water, steam coils, or steam injectors. All exposed water piping, make-up lines, and spray pumps (if applicable) that do not drain at shutdown should be traced with electric heater tape and insulated. When dry operation is planned for low ambient conditions, centrifugal fan units should be supplied with oversized fan motors to prevent motor overload when the spray water is not operating. For remote sump applications, the spray water pump must be selected for the required flow at a total head which includes the vertical lift, pipe friction (in supply and suction lines) plus the required pressure at the inlet header of the water distribution system (14 kPa). A valve should always be installed in the discharge line from the pump to permit adjusting flow to the unit requirement. Inlet water pressure should be measured by a pressure gauge installed in the water supply riser at the spray water inlet, and adjusted to the specified inlet pressure.

Overview

CCCT - C 12

coil freezing can occur even at full flow. Protective means are readily available to avoid potential freeze problems. Where the system will permit, the best protection against coil freeze-up is the use of an industrially inhibited anti-freeze solution. When this is not possible, the system must be designed to meet both of the following conditions: 1. Maintain minimum recommended flow through the coil at all times, as per the table below: 2. Maintain a heat load on the circulating fluid so that the temperature of the fluid leaving the coil will not be below 7ºC. If the process load is extremely light, or if the process is periodically shut off entirely, then an auxiliary heat load must be applied to the circulating fluid when below freezing ambient temperatures exist to prevent damage to the coil. Refer to the Heat Loss Data table (see the product section for applicable heat loss data) for the auxiliary heat load requirement. The amount of auxiliary heat necessary to prevent coil freezing can be further reduced by the use of a positive closure damper hood and insulation. Draining the coil is not recommended as a normal method of freeze protection. However, draining is acceptable as an emergency method of freeze protection. Frequent draining can promote corrosion inside the coil tubes. If the coil is not protected by an industrially inhibited anti-freeze solution, an automatic drain valve and air vent is recommended to drain the coil if flow stops or fluid temperature drops below 7ºC when the ambient temperature is below freezing. Note that cold water basin heaters will not provide freeze protection for the coil. The coil of dry and TrilliumSeries coolers can never drain completely. If a minimum heat load can not be guaranteed on the dry coil during the winter period, then the use of an anti-freeze solution is the only available protection against coil freezing. Model

Minimum Flow (l/s)

VFL 24X - 48X

4,1

VFL 72X - 96X

7,9

VXI 9, 18, 27, 36

3,5

VXI 50

5

VXI 70, C72

7

VXI 95, 145, C108

8

VXI 144, 215

13

VXI 180

11

VXI 190, 290

16

VXI 288, 430

26

VXI 360

22

FXV 42X, 43X

3

FXV 44X

5

FXV Q44X

10

FXV 5XX

6

FXV Q5XX

12

FXV 64X, 66X

7

FXV Q6XX

14

FXV D288X, D364X

18

FXV D288XQ, D364XQ

36

Warranties Please refer to the Limitation of Warranties applicable to and in effect at the time of the sale/ purchase of these products.

Baltimore Aircoil

VXI - C 1

VXI

Closed Circuit Cooling Towers

VXI Closed Circuit Cooling Towers ........................................................ C2 Benefits ....................................................................................................... C4 Construction Details .................................................................................. C6 Custom Features and Options .................................................................. C8 Accessories ............................................................................................... C10 Engineering Data ..................................................................................... C12 Structural Support .................................................................................. C20 Engineering Specifications ..................................................................... C22

Closed Circuit Cooling Towers

Product Detail

VXI - C 2

VXI Closed Circuit Cooling Towers Capacity Single Cell Capacity:

VXI

From 1,5 to 200 l/s

General Description VXI Closed Circuit Cooling Towers deliver fully rated thermal performance over a wide range of flow and temperature requirements. The VXI can be installed indoors and can accommodate limited ceiling or enclosure heights. The VXI design minimizes sound levels and installation costs, provides year-round operating reliability, and simplifies maintenance requirements.

Key Features z

Suitable for indoor and outdoor installations

z

Suitable for high temperature applications

z

Low sound

z

Single side air inlet

z

Low energy consumption

z

Low installed costs

z

Easy maintenance

z

Reliable year-round operation

z

Long service life

Baltimore Aircoil

VXI - C 3

Closed Circuit Cooling Towers

... because temperature matters

VXI - C 4

Benefits Installation and Application Flexibility z

Indoor Installations – Centrifugal fans can overcome the static pressure imposed by external ductwork, allowing these units to be installed indoors.

VXI

Low Sound z z

Centrifugal Fan - Centrifugal fans have inherently low sound characteristics. Single Side Air Inlet - Particularly sound-sensitive areas can be accommodated by facing the quiet side (back panel) to the sound-sensitive direction.

Low Energy Consumption z

Evaporative Cooling Equipment minimizes the energy consumption of the entire system because it provides lower operating temperatures. The owner saves money while conserving natural resources and reducing environmental impact.

Low Installed Cost z

z

Support – All models mount directly on two parallel I-beams (supplied by others) and ship complete with motors and drives, factory-installed and aligned. Modular Design – Large models ship in multiple sections to minimize the size and weight of the heaviest lift, allowing for the use of smaller, less costly cranes.

Easy Maintenance z

Internal Access - The interior of the unit is easily accessible for adjusting the float valve, cleaning the strainer or flushing the basin.

Long Service Life z

Materials of Construction – Various materials are available to meet the corrosion resistance, unit operating life, and budgetary requirements of any project.

Note: For more information, please refer to the section “Technical Resources, Materials of Construction”.

Reliable Year-Round Operation z

V-Belt Drive – The fans, motor, and drive system are located outside of the moist discharge airstream, protecting them from moisture, condensation and icing hence allowing a safe yearround operation.

The water level control is easily reached from the access door.

Baltimore Aircoil

External V-belt drive system (shown here with panel removed)

VXI - C 5

Low Ocean Freight Cost z

C Model in Dry Van Container

Fan Enclosures are shipped loose

... because temperature matters

Closed Circuit Cooling Towers

Size - C models are designed to fit in standard closed box containers to minimize ocean freight costs. All containerized models are shipped in a bottom fan section and a top coil section, which fit together into a 40' box container, no crating required. In order to fit the bottom fan section through the doors of the container, the fan enclosures are shipped loose inside the water basin area and are easily mounted on site.

VXI - C 6

VXI

Construction Details

Upper Section

Lower Section

Baltimore Aircoil

VXI - C 7

1. Heavy Duty Construction z

Z600 hot-dip galvanized steel panels

2. Water Distribution System Plastic spray header and branches

z

Large orifice, non-clog nozzles

z

Grommetted for easy maintenance

3. Coil z

Continuous serpentine, steel tubing

z

Hot-dip galvanized after fabrication (HDGAF)

z

Sloped tubes for free drainage of fluid

z

Designed for max. 10 bar operating pressure according to PED

4. Drift Eliminators z

UV resistant non-corrosive material, impervious to rot, decay and biological attack

z

Three distinct changes in air direction to reduce drift loss significantly

z

Assembled in easy to handle sections, which can be removed for access to the equipment interior

5. Fan Drive System z

V-belt drive

z

Heavy-duty bearings and fan motor

6. Centrifugal Fan(s) z

Quiet Operation

7. Recirculating Spray Pump z

Close coupled, bronze fitted centrifugal pump

z

Totally enclosed fan cooled (TEFC) motor

z

Bleed line with metering valve installed from pump discharge to overflow

8. Access Door z

Circular access door

9. Strainer (not shown) z

Anti-vortex design to prevent air entrainment

... because temperature matters

Closed Circuit Cooling Towers

z

VXI - C 8

Custom Features and Options Construction Options z

VXI

z

Standard Construction: Steel panels and structural elements are constructed of Z600 heavy-gauge hot-dip galvanized steel protected with the Baltiplus Corrosion Protection on the outside of the unit. Optional BALTIBOND® Corrosion Protection System: The BALTIBOND® Corrosion Protection System, a hybrid polymer coating used to extend equipment life, is applied before assembly to all hot-dip galvanized steel components of the unit.

z

Optional Stainless Steel Construction: Steel panels and structural elements are constructed of stainless steel either type 304 or 316.

z

Optional Water-Contact Stainless Steel Cold Water Basin: A cost-effective alternative to an all stainless steel unit. The critical components in the cold water basin and the cold water basin itself are provided in stainless steel. The remaining components are protected with the BALTIBOND® Corrosion Protection System.

Note: See section Technical Resources, Material of Construction for more details on the materials described above.

Coil Configurations z

Standard Serpentine Coil: The standard condensing coil is constructed of continuous lengths of all prime surface steel, hot-dip galvanized after fabrication (HDGAF).

z

Optional Extended Surface Coil: Coils are available with selected rows finned at 3 to 5 fins per inch for wet/dry applications. The coil is hot-dip galvanized after fabrication (HDGAF).

z

Optional Stainless Steel Coil: Coils are available in Type 304L or 316L stainless steel for specialized applications.

All coils are designed for low pressure drop with sloping tubes for free drainage of fluid.

Fan Drive System The fan drive system provides the cooling air necessary to reject heat from the system to the atmosphere. Centrifugal fans, forwardly curved, are driven by matched V-belts with taper lock sheaves.

Extended Surface Coil

Baltimore Aircoil

Fan Drive System

VXI - C 9

The Baltiguard® Drive System

Low Sound Operation The low sound levels generated by BAC Products with centrifugal fans make them suitable for most installations. For situations when one direction is particularly sound sensitive, the unit can be oriented so that the side opposite the air inlet faces the sound-sensitive direction. Units with centrifugal fans are also available with factory designed, tested and rated sound attenuation for both the air inlet and discharge. Note: For more information, please refer to the section “Technical Resources, Sound Reduction Options”.

Remote Sump Execution

Intake and Discharge Sound Attenuation

The use of an auxiliary sump within a heated space is the most satisfactory way to protect sump water from freezing. When the circulating pump is shut off, all the water in the water distribution, in suspension and in the sump will drain freely to the auxiliary sump. Note: For detailed information on the calculation of the remote sump tank, please refer to the section "Technical Resources, Selection of Remote Sump Tank".

... because temperature matters

Closed Circuit Cooling Towers

The BALTIGUARD® Drive System consists of two standard single-speed fan motors and drive assemblies. One drive assembly is sized for full speed and load, and the other is sized for approximately 2/3 speed and consumes only 1/3 of the design kilowatt power. This configuration allows the system to be operated like a two-speed motor, but with the reserve capacity of a standby motor in the event of failure. As a minimum, approximately 70% capacity will be available from the low kilowatt motor, even on a design wet-bulb day. Controls and wiring are the same, as those Baltiguard® Drive System required for a two-speed, two-winding motor. Significant energy savings are achieved when operating at low speed during periods of reduced load and/or low wet-bulb temperatures.

VXI - C 10

Accessories

VXI

Electric Water Level Control Package The electric water level control replaces the standard mechanical make-up valve when a more precise water level control is required. This package consists of a float switch mounted in the basin and a solenoid activated valve in the makeup water line. The valve is slow closing to minimize water hammer.

Basin Heaters Units exposed to below freezing ambient temperatures require protection to prevent freezing of the water in the cold water basin when Electric Water Level Control Package the unit is idle. Factory-installed heaters, which maintain the water temperature at 4°C, are a simple and inexpensive way of providing such protection. The heater package includes the heaters, a thermostat and a low level cut out switch to protect the heaters if the water level is too low. Standard electric heaters are selected for -18°C ambient temperature. Model No. VXI

Heaters -18°C (kW)

VXI 9-X

1 x 1,5

VXI 18-X

1 x 1,5

VXI 27-X

1 x 2,5

VXI 36-X

1x3

VXI 50-X

1x4

VXI 70-X

1x6

VXI-C72-X

1x6

VXI 95-X

1x6

VXI-C108-X

1x4

VXI 144-X

2x4

VXI 145-X

2x4

VXI 180-X

2x5

VXI 190-X

2x6

VXI 215-X

2x6

VXI 288-X

4x4

VXI 290-X

4x4

VXI 360-X

4x5

VXI 430-X

4x6

Capacity Control Dampers Modulating capacity control dampers are available to provide better leaving water temperature control than can be obtained from fan cycling alone. Fan discharge dampers consist of a single airfoil type damper blade located in the discharge of each fan housing. A standard electrical control package for dampers is available from BAC.

Baltimore Aircoil

VXI - C 11

Extended Lubrication Lines Extended lubrication lines with grease fittings are available for lubrication of the fan shaft bearings.

Solid Bottom Panels Factory-installed bottom panels are required when intake air is ducted to the unit.

In the event the owner requires easy access to the top of the unit, the unit can be furnished with ladders extending from the base of the unit to the top, as well as safety cages, and handrail packages.

Extended Lubrication Lines

Note: When these access options are employed, the unit must be equipped with steel drift eliminators.

Discharge Hoods Discharge hoods reduce the risk of re-circulation in tight enclosures by increasing discharge air velocity, and can be used to elevate the unit discharge above adjacent walls to comply with layout guidelines.

Plume Abatement Coil The use of plume abatement coils is recommended to reduce significantly the formation of visible plume during wet operation and extend the dry operation capability of the closed circuit cooling tower. The combination of Discharge Hood discharge air reheating and extended dry operation minimises plume formation during weather conditions with high relative humidity. Plume abatement coils are also an effective way to save water and water treatment costs. Note: For more information, please refer to the section “Technical Resources, Plume Abatement”.

Basin Sweeper Piping Basin sweeper piping provides an effective method of preventing sediment from collecting in the cold water basin of the unit. A complete piping system, including nozzles, is provided in the unit basin for connection to side stream filtration equipment. Note: For more information, please refer to the section "Technical Resources, Filtration".

Basin Sweeper Piping

... because temperature matters

Closed Circuit Cooling Towers

Ladder, Safety Cage and handrails

VXI - C 12

Engineering Data REMARK: Do not use for construction. Refer to factory certified dimensions & weights. This brochure includes data current at time of publication, which should be reconfirmed at the time of purchase. In the interest of product improvement, specifications, weights and dimensions are subject to change without notice. Up-to-date engineering data and more can be found at www.BaltimoreAircoil.com.

VXI

VXI 9 - VXI 36

1. Drain ND50; 2. Outlet Connection ND80 for VXI 9-X and ND100 for VXI 18-X, VXI 27-X and VXI 36-X; 3. Overflow ND50; 4. Make Up ND25; 5. Inlet Connection ND80 for VXI 9-X and ND100 for VXI 18-X, VXI 27-X and VXI 36-X; 6. Vent ND15; 7. Access Door (not shown).

Model No. VXI

Operating Weight (kg)

Shipping Weight (kg)

Heaviest Section (kg)

H (mm)

L (mm)

W (mm)

Air Flow (m3/s)

Fan Motor (kW)

Spray Water Flow (l/s)

Pump Motor (kW)

Coil Volume (l)

VXI 9-1 VXI 9-2 VXI 9-3

780 870 980

670 760 830

660* 480 540

2245 2467 2683

914 914 914

1207 1207 1207

2,3 2,2 2,5

(1x) 1,5 (1x) 1,5 (1x) 2,2

2,2 2,2 2,2

(1x) 0,25 (1x) 0,25 (1x) 0,25

(1x) 75 (1x) 95 (1x) 115

VXI 18-0 VXI 18-1 VXI 18-2 VXI 18-3

1120 1270 1440 1650

920 1030 1160 1330

920* 1030* 700 860

2035 2245 2467 2683

1829 1829 1829 1829

1207 1207 1207 1207

4,6 5,0 4,8 5,5

(1x) 4,0 (1x) 4,0 (1x) 4,0 (1x) 5,5

4,7 4,7 4,7 4,7

(1x) 0,37 (1x) 0,37 (1x) 0,37 (1x) 0,37

(1x) 98 (1x) 140 (1x) 182 (1x) 224

VXI 27-1 VXI 27-2 VXI 27-3

1760 1990 2300

1320 1500 1730

1320* 1000 1200

2343 2578 2813

2737 2737 2737

1207 1207 1207

7,6 6,8 7,1

(1x) 5,5 (1x) 5,5 (1x) 7,5

7,1 7,1 7,1

(1x) 0,75 (1x) 0,75 (1x) 0,75

(1x) 205 (1x) 269 (1x) 333

VXI 36-2 VXI 36-3

2300 2850

1800 2080

1200 1440

2578 2813

3658 3658

1207 1207

10,4 10,9

(1x) 7,5 (1x) 11

9,5 9,5

(1x) 0,75 (1x) 0,75

(1x) 356 (1x) 442

* Unit ships in one piece.

Baltimore Aircoil

VXI - C 13

VXI 50 - VXI 70

Model No. VXI

Operating Weight (kg)

Shipping Weight (kg)

Heaviest Section (kg)

H (mm)

L (mm)

W (mm)

Air Flow (m3/s)

Fan Motor (kW)

Spray Water Flow (l/s)

Pump Motor (kW)

Coil Volume (l)

VXI 50-2 VXI 50-3 VXI 50-4

3740 4280 4825

2670 2950 3255

1720 1980 2240

3093 3328 3563

3645 3645 3645

1438 1438 1438

14,6 15,7 16,9

(1x) 11 (1x) 11 (1x) 15

13,9 13,9 13,9

(1x) 1,5 (1x) 1,5 (1x) 1,5

(1x) 515 (1x) 638 (1x) 762

VXI 70-2 VXI 70-3 VXI 70-4

6490 7190 8075

4250 4770 5315

2630 3150 3665

3586 3821 4056

3550 3550 3550

2397 2397 2397

20,8 22,9 22,2

(1x) 15 (1x) 18,5 (1x) 18,5

19,2 19,2 19,2

(1x) 2,2 (1x) 2,2 (1x) 2,2

(2x) 356 (2x) 442 (2x) 527

VXI C72 - C108

1. Drain ND50; 2. Outlet Connection ND100; 3. Overflow ND50; 4. Make Up ND25; 5. Inlet Connection ND100; 6. Vent ND15; 7. Access Door.

Model No. VXI

Operating Weight (kg)

Shipping Weight (kg)

Heaviest Section (kg)

H (mm)

L (mm)

W (mm)

Air Flow (m3/s)

Fan Motor (kW)

Spray Water Flow (l/s)

Pump Motor (kW)

Coil Volume (l)

VXI C072-2 VXI C072-3 VXI C072-4

6490 7190 8075

4250 4770 5315

2630 3150 3665

3585 3820 4055

3550 3550 3550

2245 2245 2245

20,8 22,9 22,2

(1x) 15 (1x) 18,5 (1x) 18,5

19,2 19,2 19,2

(1x) 2,2 (1x) 2,2 (1x) 2,2

(2x) 356 (2x) 442 (2x) 527

VXI C108-2 VXI C108-3 VXI C108-4

9695 10630 11760

6145 6945 7830

3885 4685 5485

3585 3820 4055

5385 5385 5385

2245 2245 2245

33,5 32,2 31,1

(1x) 22 (1x) 22 (1x) 22

29,0 29,0 29,0

(1x) 4,0 (1x) 4,0 (1x) 4,0

(2x) 532 (2x) 661 (2x) 790

... because temperature matters

Closed Circuit Cooling Towers

1. Drain ND50; 2. Outlet Connection ND100; 3. Overflow ND 80; 4. Make Up ND25 for VXI 50-X and ND50 for VXI 70-X; 5. Inlet Connection ND100; 6. Vent ND 15; 7. Access Door.

VXI - C 14

VXI

VXI 95 - VXI 290

1. Drain ND50 (not shown); 2. Outlet Connection ND100; 3. Overflow ND80; 4. Make Up ND50; 5. Inlet Connection ND100; 6. Vent ND15; 7. Access Door.

Model

Operating Weight (kg)

Shipping Weight (kg)

Heaviest Section (kg)

H (mm)

L (mm)

W (mm)

Air Flow (m3/s)

Fan Motor (kW)

Spray Water Flow (l/s)

Pump Motor (kW)

Coil Volume (l)

VXI 95-2 VXI 95-3 VXI 95-4

7740 8630 9520

4990 5630 6180

3200 3850 4470

4013 4248 4483

3550 3550 3550

2397 2397 2397

27,6 26,7 26,2

(1x) 30 (1x) 30 (1x) 30

25,2 25,2 25,2

(1x) 2,2 (1x) 2,2 (1x) 2,2

(2x) 448 (2x) 556 (2x) 664

VXI 145-1 VXI 145-2 VXI 145-3 VXI 145-4

10100 11460 12810 14160

6300 7280 8175 9260

3780 4715 5710 6690

3778 4013 4248 4483

5385 5385 5385 5385

2397 2397 2397 2397

39,9 38,6 37,5 36,6

(1x) 37 (1x) 37 (1x) 37 (1x) 37

38,5 38,5 38,5 38,5

(1x) 4 (1x) 4 (1x) 4 (1x) 4

(2x) 506 (2x) 669 (2x) 832 (2x) 995

VXI 190-2 VXI 190-3 VXI 190-4

15400 17160 18920

9820 11100 12305

3390* 3840 4470

4013 4248 4483

7226 7226 7226

2397 2397 2397

55,4 53,4 52,5

(2x) 30 (2x) 30 (2x) 30

50,4 50,4 50,4

(2x) 2,2 (2x) 2,2 (2x) 2,2

(4x) 448 (4x) 556 (4x) 664

VXI 290-1 VXI 290-2 VXI 290-3 VXI 290-4

20350 22980 25700 28420

12680 14570 16550 18505

5120* 5120* 5710 6690

3778 4013 4248 4483

10903 10903 10903 10903

2397 2397 2397 2397

79,5 77,8 75,0 73,1

(2x) 37 (2x) 37 (2x) 37 (2x) 37

77,0 77,0 77,0 77,0

(2x) 4 (2x) 4 (2x) 4 (2x) 4

(4x) 506 (4x) 669 (4x) 832 (4x) 995

* Pan section is heaviest section.

Baltimore Aircoil

VXI - C 15

VXI 180 - VXI 360

Model

Operating Weight (kg)

Shipping Weight (kg)

Heaviest Section (kg)

H (mm)

L (mm)

W (mm)

Air Flow (m3/s)

Fan Motor (kW)

Spray Water Flow (l/s)

Pump Motor (kW)

Coil Volume (l)

VXI 180-2 VXI 180-3 VXI 180-4

12970 14590 16250

8990 10200 11530

5810 7010 8200

4075 4310 4545

5388 5388 5388

3000 3000 3000

51,4 50,0 52,0

(2x) 18,5 (2x) 18,5 (2x) 22,0

46,7 46,7 46,7

(1x) 4 (1x) 4 (1x) 4

(2x) 847 (2x) 1052 (2x) 1258

VXI 360-2 VXI 360-3 VXI 360-4

25840 29090 32500

17940 20380 23100

5810 7010 8200

4075 4310 4545

10903 10903 10903

3000 3000 3000

102,9 100,1 104,0

(4x) 18,5 (4x) 18,5 (4x) 22,0

93,4 93,4 93,4

(2x) 4 (2x) 4 (2x) 4

(4x) 847 (4x) 1052 (4x) 1258

VXI 144 - VXI 430

1. Drain ND50; 2. Outlet Connection ND100. 3. Overflow ND80; 4. Make Up ND50 for VXI 144-X, VXI 215-X, VXI 288-X and ND80 for VXI 430X; 5. Inlet Connection ND 100; 6. Vent ND15; 7. Access Door.

... because temperature matters

Closed Circuit Cooling Towers

1. Drain ND50; 2. Outlet Connection ND100; 3. Overflow ND80; 4. Make Up ND50 for VXI 180-X and ND80 for VXI 360-X; 5. Inlet Connection ND100; 6. Vent ND15; 7. Access Door.

VXI

VXI - C 16

Model

Operating Weight (kg)

Shipping Weight (kg)

Heaviest Section (kg)

H (mm)

L (mm)

W (mm)

Air Flow (m3/s)

Fan Motor (kW)

Spray Water Flow (l/s)

Pump Motor (kW)

Coil Volume (l)

VXI 144-2 VXI 144-3 VXI 144-4

12070 13390 14710

7270 8210 8470

4680 5610 6550

4075 4310 4545

3550 3550 3550

3607 3607 3607

38,6 40,2 39,4

(1x) 30 (1x) 37 (1x) 37

39,1 39,1 39,1

(1x) 4 (1x) 4 (1x) 4

(2x) 686 (2x) 851 (2x) 1015

VXI 215-1 VXI 215-2 VXI 215-3 VXI 215-4

15830 17730 19730 21690

9130 10460 12035 13435

5510 6900 8310 9710

3840 4075 4310 4545

5388 5388 5388 5388

3607 3607 3607 3607

59,4 57,9 62,3 60,4

(2x) 22 (2x) 22 (2x) 30 (2x) 30

56,8 56,8 56,8 56,8

(1x) 4 (1x) 4 (1x) 4 (1x) 4

(2x) 774 (2x) 1024 (2x) 1272 (2x) 1521

VXI 288-2 VXI 288-3 VXI 288-4

24230 26850 29540

14520 16520 18280

5280* 5610 6550

4075 4310 4545

7226 7226 7226

3607 3607 3607

77,3 80,0 78,8

(2x) 30 (2x) 37 (2x) 37

78,2 78,2 78,2

(2x) 4 (2x) 4 (2x) 4

(4x) 686 (4x) 851 (4x) 1015

VXI 430-1 VXI 430-2 VXI 430-3 VXI 430-4

31750 35550 39550 43560

18230 20890 23770 26845

7210* 7210* 8300 9710

3840 4075 4310 4545

10903 10903 10903 10903

3607 3607 3607 3607

119,2 115,9 124,6 120,7

(4x) 22 (4x) 22 (4x) 30 (4x) 30

113,6 113,6 113,6 113,6

(2x) 4 (2x) 4 (2x) 4 (2x) 4

(4x) 774 (4x) 1024 (4x) 1272 (4x) 1521

* Pan section is heaviest section.

General Notes 1. Make up, overflow, suction, drain connections and access door can be provided on side opposite to that shown; consult your BAC Balticare representative.

8. On models VXI 9 to VXI 36 access doors are located at the opposite of the air inlet side, ensure sufficient space for entry when positioning these units.

2. Unit height is indicative, for precise value refer to certified print.

9. When flow rate on models VXI 27, VXI 36 and VXI 50 exceeds 30 l/s the quantity of coil connections will be double. When flow rate on models VXI 70, VXI C72, VXI C108, VXI 95, VXI 145, VXI 180, VXI 144, VXI 215 exceeds 60 l/s the coil connections will be double When flow rate on models VXI 190, VXI 290, VXI 360, VXI 288 and VXI 430 exceeds 120 l/s the quantity of coil connections will be double.

3. Shipping/operating weights indicated are for units without accessories such as sound attenuators, discharge hoods, etc. Consult factory certified prints to obtain weight additions and the heaviest section to be lifted. 4. The drawings for units with only one spray pump show the standard “right hand” arrangement, which has the air inlet side on the right when facing the connection end. “Left hand” arrangement can be furnished by special order. 5. Coil, overflow, make-up and spray water connections are always located on the same end of the unit. For double pump units an additional set of coil connections and an additional overflow connection will be installed on the other end of the unit. 6. For indoor applications of closed circuit cooling towers, the room may be used as a plenum with ductwork attached to the discharge only. If inlet ductwork is required, an enclosed fan section must be specified; consult your BAC Balticare representative for details. 7. Fan kW is at 0 Pa ESP. To operate against external static pressure up to 125 Pa, increase each fan motor one size.

10. Models VXI 9 through VXI 145 have one coil section and one fan motor, which can be switched on and off. Models VXI-95, 144, 145, 180 and 215 have one coil section and one or two fan motors. Fan cycling results in only on-off operation. On these units all fans need to operate simultaneously. Models VXI-190, 288, 290, 360 and 430 have 2 coil casing sections and one or two fan motors per coil casing section. Fan cycling results in only on-off operation. On these units all fans need to operate simultaneously per coil casing section. Multiple speed motors are available for additional steps of capacity control. Modulating capacity control can be obtained with fan discharge dampers. Consult your local BAC Balticare representative for details. 11. For dry operation, standard motors must be increased one size to avoid motor overloading. Extended surface coils are available to vastly increase dry capacity without motor size increase. Consult your local BAC Balticare representative for selection and pricing.

Baltimore Aircoil

VXI - C 17

Sound Attenuation REMARK: Do not use for construction. Refer to factory certified dimensions & weights. This brochure includes data current at time of publication, which should be reconfirmed at the time of purchase. In the interest of product improvement, specifications, weights and dimensions are subject to change without notice. Up-to-date engineering data and more can be found at www.BaltimoreAircoil.com.

XA + XB Sound Attenuation

XC Sound Attenuation

1. Access Door; L1= Intake Attenuator Length; L2= Discharge Attenuator Length; W= Unit Width; H.= Unit Height (see Engineering Data).

... because temperature matters

Closed Circuit Cooling Towers

1. Access Door; L1= Intake Attenuator Length; L2= Discharge Attenuator Length; W= Unit Width; H.= Unit Height (see Engineering Data).

VXI - C 18

VXI

Unit + Atten. # Access # pieces doors (2) XA, XB, XC shipped

VXI

XA, XB, XC

Dimensions (mm) W2

H1

Disch. Int. XA, XB XC Att. Att.

W1

Weights (kg) L1

L2

XA, XB, XC

Intake

Discharge

XA

XB

XC

Solid Bottom

Total

XA

XB

XC

XA

XB

XC

9-X

4(1)

1

2

2352

N.A. 1090 1030

890

902

110

130

N.A.

30

130

150

N.A.

270

310

N.A.

18-X

4(1)

1

2

2352

N.A. 1090 1030 1800

1816

175

220

N.A.

50

175

220

N.A.

400

490

N.A.

27-X

4

1

2

2352

N.A. 1090 1030 2710

2731

230

300

N.A.

70

280

350

N.A.

580

720

N.A.

36-X

4

1

2

2352

N.A. 1090 1030 3635

3645

300

370

830

100

360

420

N.A.

760

890

N.A.

50-X

4

1

2

2583

3728 1600 1420 3635

3645

380

480 1080

120

440

520 1070 940 1120 2270

70-X

4

1

2

3542

4687 2070 1955 3525

3645

500

630 1420

190

530

650 1330 1220 1470 2940

C72-X

4

1

2

3390

4535 2070 1955 3525

3645

500

630 1420

190

530

650 1330 1220 1810 3400

95-X

4

1

2

3542

4687 2070 2365 3525

3645

500

630 1420

190

660

800 1640 1350 1620 3250 970 1980 1720 2590 4920

C108-X

4

2

2

3390

4535 2070 1955 5365

5480

660

860 1970

300

760

145-X

4

2

2

3542

4687 2070 2365 5365

5480

660

860 1970

300

830 1090 2240 1790 2250 4510

190-X

7

2

2

3542

4687 2070 2365 7050

7322 1000 1260 2840

380

1320 1600 3280 2700 3240 6500

290-X

7

4

2

3542

4687 2070 2365 10730 10998 1320 1720 3940

600

1660 2180 4480 3580 4500 9020

180-X

4

2

2

4145

5290 2560 2965 5365

980 2240

350

900 1210 2490 1980 2540 5080

360-X

7

4

2

4145

5290 2560 2965 10730 10994 1460 1960 4480

5480

730

700

1800 2420 4980 3960 5080 10160

144-X

4

1

2

4752

5897 2560 3575 3525

3645

560

710 1620

280

810 1030 2130 1650 2020 4030

215-X

4

2

2

4752

5897 2560 3575 5365

5480

730

980 2240

420

1020 1410 2920 2170 2810 5580

288-X

7

2

2

4752

5897 2560 3575 7050

7322 1120 1420 3240

560

1620 2060 4260 3300 4040 8060

430-X

7

4

2

4752

5897 2560 3575 10730 10994 1460 1960 4480

840

2040 2820 5840 4340 5620 11160

(1) VXI 9-1, VXI 18-0 and VXI 18-1 + Attenuator are shipped in 3 pieces (2) Intake Attenuator: Access opening is 775 mm high, 405 mm wide and is located at each end of the unit. (2) Discharge Attenuator : Access opening is 405 mm high, 1170 mm wide and is located at blank off side of the unit (VXI-9-X has 650 mm width)

Baltimore Aircoil

VXI - C 19

Heat Loss Data Model No. VXI

Minimum flow (l/s)

9-1 9-2 9-3

Heatloss Data (kW) (1) Unit with Hood and PCD's

3,5

5,1 6,2 6,9

3,6 4,0 4,3

18-0 18-1 18-2 18-3

3,5

7,3 9,7 11,8 13,6

5,4 5,8 6,1 6,5

27-1 27-2 27-3

3,5

15,1 18,2 20,6

9,0 9,7 10,4

36-2 36-3

3,5

23,8 27,2

13,3 14,1

50-2 50-3 50-4

5,0

32,7 37,4 42,1

16,9 17,7 18,5

70-2 70-3 70-4

7,0

44,8 50,9 57,0

17,7 18,4 19,1

C72-2 C72-3 C72-4

7,0

44,8 50,9 57,0

17,7 18,4 19,1

95-2 95-3 95-4

8,0

74,3 84,0 93,7

27,2 28,6 30,0

C108-2 C108-3 C108-4

8,0

67,0 75,8 84,6

27,2 28,4 29,6

144-2 144-3 144-4

13,0

112,8 127,6 141,6

25,9 26,4 27,7

145-1 145-2 145-3 145-4

8,0

95,6 111,8 126,0 140,2

35,8 37,6 39,5 41,5

180-2 180-3 180-4

11,0

101,7 114,9 128,1

34,0 35,5 37,0

190-2 190-3 190-4

16,0

149,4 168,9 188,4

63,7 66,9 70.2

215-1 215-2 215-3 215-4

13,0

142,6 169,9 191,5 212,0

54,1 56,8 59,7 62,7

288-2 288-3 288-4

26,0

222,0 248,9 276,3

76,3 80,1 84,1

290-1 290-2 290-3 290-4

16,0

187,2 223,6 252,0 280,4

71,6 75,2 78,9 82,7

360-2 360-3 360-4

22,0

200,4 227,1 253,8

68,5 71,0 73,5

430-1 430-2 430-3 430-4

26,0

280,9 334,8 377,3 418,8

108,8 114,3 120,0 126,0

(1) Heat loss data based on 10°C water and -14°C ambient temperature with 20 m/s wind velocity (fans and pump off)

Remote Sump Data Refer to the "Technical Resources" section "Selection of Remote Sump" for Remote Sump Data.

... because temperature matters

Closed Circuit Cooling Towers

Standard Unit

VXI - C 20

Structural Support REMARK: Do not use for construction. Refer to factory certified dimensions & weights. This brochure includes data current at time of publication, which should be reconfirmed at the time of purchase. In the interest of product improvement, specifications, weights and dimensions are subject to change without notice. Up-to-date engineering data and more can be found at www.BaltimoreAircoil.com.

VXI

The recommended support arrangement for units consists of parallel I-beams running the full length of the unit, spaced as shown in the following drawing. Besides providing adequate support, the steel also serves to raise the unit above any solid foundation to ensure access to the bottom of the unit. To support units in an alternate steel support arrangement, consult your BAC Balticare Representative.

Units without Sound Attenuation

1. Outline of Unit; 2. Mounting holes Ø 22 mm, 3. Unit; 4. Air Intake.

Notes: 1. The recommended support arrangement for VX units consists of parallel I-beams extending the full length of the unit. Supports and anchor bolts are to be designed and furnished by others. 2. All supporting beams are to be flush and level at top and must be oriented relative to gage line as shown. 3. Recommended design loads for each unit support beam should be 70% of the total unit operating weight applied as a uniform load to each of the unit beams. The support beam(s) for the optional intake attenuator(s) needs to carry attenuator only, uniform load of 250 kg/m. Beams should be designed in

accordance with standard structural practice. For the maximum allowable deflection of beams under the unit refer to above table. 4. All mounting holes have a diameter of 22 mm at the locations shown. 5. If vibration isolators are used, a rail or channel must be provided between the unit (and optional attenuator) and the isolators to provide continuous unit support. Additionally the support beams must be designed to accommodate the overall length and mounting hole location of the isolators that may differ from those of the unit. Refer to vibration isolator drawings for these data.

Baltimore Aircoil

VXI - C 21

Units with Sound Attenuation

C D Center dis. Center dis. Length Width (mm) (mm)

Model VXI

A Unit Length (mm)

B Unit width (mm)

E (mm)

F (mm)

G (mm)

X Max. Deflection (mm)

Mounting holes

9-X

914

1207

750

1153

-

-

-

2

4

18-X

1829

1207

1664

1153

-

-

-

5

4

27-X

2737

1207

2572

1153

-

-

-

8

4

36-X

3658

1207

3492

1153

-

-

-

10

4

50-X

3645

1438

3492

1378

-

-

-

10

4

70-X

3550

2397

3238

2397

-

-

-

10

4

C72-X

3550

2245

3238

2175

-

-

-

10

4

95-X

3550

2397

3238

2327

-

-

-

10

4

C108-X

5385

2245

5074

2175

2486

102

-

13

8

145-X

5385

2397

5074

2327

2486

102

-

13

8

190-X

7226

2397

6914

2327

3238

438

-

13

8

290-X

10903

2397

10586

2327

2486

102

438

13

16

180-X

5388

3000

5074

2934

2486

102

-

13

8

360-X

10903

3000

10586

2934

2486

102

438

13

16

144-X

3550

3607

3238

3537

-

-

-

10

4

215-X

5388

3607

5074

3537

2486

102

-

13

8

288-X

7226

3607

6914

3537

3238

438

-

13

8

430-X

10903

3607

10586

3537

2486

102

438

13

16

... because temperature matters

Closed Circuit Cooling Towers

1. Outline of Unit; 2. Mounting Holes Ø 22 mm; 3. Outline of attenuator (optional XA or XB);4. Support Channel attached to optional XA or XB attenuator; 5.+3. Outline of Attenuator (optional XC); 6.+4. Support Channels attached to optional XC attenuator; 7. Unit; 8. Sound Attenuator; 9. Air Intake.

VXI - C 22

Engineering Specifications

VXI

1.0 Closed Circuit Cooling Tower 1.0 General: Furnish and install ____factory assembled, forced draft, centrifugal fan, closed circuit cooling tower(s) with vertical air discharge, conforming in all aspects to the specifications and schedules as shown on the plans. Overall dimensions shall not exceed approximately ____mm long x ____mm wide x ____ mm high. The total connected fan kW shall not exceed ____kW. The total connected pump kW shall not exceed ____kW. The closed circuit cooling tower(s) shall be Baltimore Aircoil Company Model(s) ________________. 1.2. Thermal Capacity (water as heat transfer fluid): The closedcircuit cooling tower(s) shall be warranted by the manufacturer to cool ______l/s of _______ water from ____°C to ____°C at ____°C entering wet-bulb temperature. (Alternate1.2.) Thermal Capacity (aqueous glycol solution as heat transfer fluid): The closed circuit cooling tower(s) shall be warranted by the manufacturer to cool ________l/s of _____% by volume ethylene/propylene glycol solution from ______°C to _____°C at _____°C entering wet-bulb temperature. Coil pressure drop shall not exceed ________bar. 1.3. Corrosion Resistant Construction: Unless otherwise noted in this specification, all steel panels and structural members shall be constructed of heavy-gauge Z600 metric hot-dip galvanized steel, with all sheared edges given a protective coating of zinc-rich

compound and the exterior protected with the Baltiplus Corrosion Protection. (Alternate1.3.) Corrosion Resistant Construction: Unless otherwise noted in this specification, all steel panels and structural members shall be protected with the BALTIBOND® Corrosion Protection System. The system shall consist of Z600 metric hot-dip galvanized steel prepared in a four-step (clean, pre-treat, rinse, and dry) process with an electrostatically sprayed, thermosetting hybrid polymer fusebonded to the substrate during a thermally activated curing stage and monitored by a 23-step quality assurance program. (Alternate 1.3) Corrosion Resistant Construction: Unless otherwise noted in this specification, all steel panels and structural members shall be constructed of Type 304 or 316 stainless steel and assembled with stainless steel nut and bolt fasteners. 1.4. Quality Assurance: The closed circuit cooling tower manufacturer shall have a management system certified by an accredited registrar as complying with the requirements of ISO9001:2000 to ensure consistent quality of its products and services. 1.5. Warranty: The manufacturer’s standard equipment warranty shall be for a period of not less than one year from date of startup or eighteen months from date of shipment, whichever occurs first.

2.0 Construction Details 2.1.Tower Structure: The closed circuit cooling tower shall be constructed of heavy-gauge steel utilizing double-brake flanges for maximum strength and rigidity and reliable sealing of water-tight joints. All sheared edges shall be protected with a coating of zinc-rich compound. 2.2. Casing Assembly: The closed circuit cooling tower shall include a coil casing section consisting of a serpentine coil, spray water distribution system, and drift eliminators, as indicated by the manufacturer. Plastic drift eliminators shall be removable in easily handled sections. They shall incorporate a minimum of three changes in air direction. 2.3. Coil Assembly: The cooling coil shall be fabricated of continuous lengths of all prime surface steel at the manufacturer’s own facility, and hot-dip galvanized after fabrication. The cooling coil shall be pneumatically tested at 15 bar. The cooling coil shall be designed for low pressure drop with sloping tubes for free drainage of fluid and shall be compliant to PED. Maximum allowable working pressure shall be 10 bar. 2.4. Water Distribution System: Water shall be distributed evenly over the coil at a minimum flow rate of 3,1 l/s/m to ensure complete wetting of the coil at all times by large-diameter, non-clog, plastic 360° distribution nozzles, spaced across the coil face area in PVC spray branches by snap-in rubber grommets, allowing quick removal of individual nozzles or complete branches for cleaning or flushing.

Nozzles shall utilize a two-stage diffusion pattern to provide overlapping, umbrella spray patterns that create multiple intersection points with adjacent nozzles. 2.5. Spray Pump System: The closed circuit cooling tower shall include a close-coupled, bronze-fitted centrifugal pump equipped with a mechanical seal, mounted on the basin and piped to the suction strainer and water distribution system. It shall be installed so that it can be drained when the basin is drained. The pump assembly shall include a metering valve and bleed line to control the bleed rate from the pump discharge to the overflow connection. The pump motor shall be totally enclosed fan cooled (TEFC) type with IP 55 protection and class B insulation suitable for outdoor service, _____ kW, _______Volt, ________Hz, ______Phase. (Alternate 2.5.) Spray Pump System-Remote Sump: On installations requiring a remote sump, the closed circuit cooling tower shall be modified to accommodate the use of an independent basin and pump (both by others) for recirculating water. 2.6. Basin Assembly: The combination basin/fan section shall be constructed of heavy-gauge Z600 galvanized steel. The basin shall be provided with large area lift out strainers with perforated openings sized smaller than the water distribution nozzles and an anti-vortexing device to prevent air entrainment. The strainer and vortex device shall be constructed of the same material as the cold water basin to prevent dissimilar metal corrosion.

3.0 Mechanical Equipment 3.1. Fan System: The fans and motors shall be factory installed at the base of the unit in the dry entering air stream to provide greater reliability and ease of maintenance. The forwardly curved centrifugal fans shall be heavy-duty centrifugal flow types. Fan housings shall have curved inlet rings for efficient air entry and rectangular discharge cowls shall extend into the basin to increase fan efficiency and prevent water from entering the fans. Fans shall be mounted on a steel fan shaft supported by heavy-duty self-aligning, relubricatable ball bearings with cast iron housings and designed for a minimum L10 life of 40 000 hours (280 000 hrs average life). The fan shaft shall be protected with a two-part epoxy coating for corrosion protection.

3.2. Fan Motor/Drive System: Fan motor(s) shall be totally enclosed fan cooled (TEFC), IP-55, class F, selected for _____Pa static pressure. Fan motor(s) shall be suitable for _____ volts, ____ phase, ____ Hz electrical service and shall be mounted on an easily adjusted, heavy-duty motor base. V-belt drives and all moving parts are protected with removable screens. (Alternate 3.2.) Baltiguard® Fan System: Two single speed fan motors, one sized for full speed and load, the other sized for 2/3 speed and approximately 1/3 of full load kW shall be provided in each cell for capacity control and standby protection from drive or motor failure. Two-speed motor(s) is not an acceptable alternative.

Baltimore Aircoil

VXI - C 23

4.0 Drift Eliminators 4.1 Drift Eliminators: Eliminators shall be constructed of specially formulated plastic material and be removable in easily handled sections. They shall have a minimum of three changes in air direction.

5.0 Access 5.1 Basin Access: Circular access doors shall be provided for easy access to the make-up water assembly and suction strainer for routine maintenance.

6.1 Sound Level: To maintain the quality of the local environment, the maximum sound pressure levels (dB) measured 15 m from the

Location

63

125

250

500

cooling tower operating at full fan speed shall not exceed the sound levels detailed below.

1000

2000

4000

Discharge Air Inlet End Back

... because temperature matters

8000

dB(A)

Closed Circuit Cooling Towers

6.0 Sound

VFL - C 1

VFL

Closed Circuit Cooling Towers

VFL Closed Circuit Cooling Tower ......................................................... C2 Benefits ....................................................................................................... C4 Construction Details .................................................................................. C6 Custom Features and Options .................................................................. C7 Accessories ................................................................................................. C9 Engineering Data ..................................................................................... C11 Structural Support .................................................................................. C16 Engineering Specifications ..................................................................... C17

Closed Circuit Cooling Towers

Product Detail

VFL - C 2

VFL Closed Circuit Cooling Tower Capacity Single Model Capacity:

VFL

1 to 65 l/s

General Description VFL Closed Circuit Cooling Towers deliver fully rated thermal performance over a wide range of flow and temperature requirements. The VFL can be installed indoors and minimize sound levels, and are available to accommodate limited ceiling or enclosure heights. The VFL design minimizes installation costs, provides year-round operating reliability, and simplifies maintenance requirements.

Key Features z

Suitable for indoor and outdoor installations

z

Suitable for high temperature applications

z

Suitable for locations with limited ceiling or enclosure heights and roof top installations

z

Low sound

z

Single side air inlet

z

Low energy consumption

z

Low installed cost

z

Easy maintenance

z

Reliable year-round operation

z

Long service life

Baltimore Aircoil

VFL - C 3

Closed Circuit Cooling Towers

... because temperature matters

VFL - C 4

Benefits Installation and Application Flexibility

VFL

z

z

Indoor Installations – Centrifugal fans can overcome the static pressure imposed by external ductwork, allowing this type of cooling towers to be installed indoors. Low Profile Models – The fan section of low profile units is adjacent to the casing section to yield models suitable for use in height sensitive installations. Low profile models are available in heights of 1855 mm up to 2560 mm.

Low Sound z

z

Low profile unit shown in contrast to a standard unit

Centrifugal Fan - Centrifugal fans have inherently low sound characteristics. Single Side Air Inlet - Particularly soundsensitive areas can be accommodated by facing the quiet side (back panel) to the soundsensitive direction.

Low Energy Consumption z

Evaporative Cooling Equipment minimizes the energy consumption of the entire system because it provides lower operating temperatures. The owner saves money while conserving natural resources and reducing environmental impact.

Low Installed Cost z

z

Support – All models mount directly on two parallel I-beams (supplied by others) and ship complete with motors and drives, factoryinstalled and aligned. Modular Design – All models without intake or discharge accessories ship in one piece to minimize field installation time and lifting time.

Easy Maintenance z

Internal Access - The interior of the unit is easily accessible for adjusting the float valve, cleaning the strainer or flushing the basin.

Baltimore Aircoil

Modular Design

VFL - C 5

Reliable Year-Round Operation z

V-Belt Drive – The fans, motor, and drive system are located outside of the moist discharge airstream, protecting them from moisture, condensation and icing hence allowing a safe yearround operation.

Long Service Life z

Note: For more information, please refer to the section “Technical Resources, Materials of Construction”.

The interior of the unit is easily accessible

V-Belt Drive for Series VL

... because temperature matters

Closed Circuit Cooling Towers

Materials of Construction – Various materials are available to meet the corrosion resistance, unit operating life, and budgetary requirements of any project.

VFL - C 6

VFL

Construction Details

1. Heavy Duty Construction z

z

Z600 hot-dip galvanized steel panels

Assembled in easy to handle sections, which can be removed for access to the equipment interior

5. Fan Drive System 2. Water Distribution System z

Plastic spray header and branches

z

Large orifice, non-clog nozzles

z

Grommetted for easy maintenance

z

V-belt drive

z

Heavy-duty bearings and fan motor

6. Centrifugal Fan(s) z

Quiet Operation

3. Coil z

Continuous serpentine, steel tubing

z

Hot-dip galvanized after fabrication (HDGAF)

z

Sloped tubes for free drainage of fluid

z

Designed for max. 10 bar operating pressure according to PED

7. Recirculating Spray Pump z

Close coupled, bronze fitted centrifugal pump

z

Totally enclosed fan cooled (TEFC) motor

z

Bleed line with metering valve installed from pump discharge to overflow

8. Access Door 4. Drift Eliminators z

z

UV resistant non-corrosive material, impervious to rot, decay and biological attack Three distinct changes in air direction to reduce drift loss significantly

z

Circular access door

9. Strainer (Not Shown) z

Baltimore Aircoil

Anti-vortex design to prevent air entrainment

VFL - C 7

Custom Features and Options Construction Options z

Optional BALTIBOND® Corrosion Protection System: The BALTIBOND® Corrosion Protection System, a hybrid polymer coating used to extend equipment life, is applied before assembly to all hot-dip galvanized steel components of the unit.

Stainless Steel Cold Water Basin

z

Optional Stainless Steel Construction: Steel panels and structural elements are constructed of stainless steel either type 304 or 316.

z

Optional Water-Contact Stainless Steel Cold Water Basin: A cost-effective alternative to an all stainless steel unit. The critical components in the cold water basin and the cold water basin itself are provided in stainless steel. The remaining components are protected with the BALTIBOND® Corrosion Protection System.

Note: See section Technical Resources, Material of Construction for more details on the materials described above.

Coil Configurations z

Standard Serpentine Coil: The standard condensing coil is constructed of continuous lengths of all prime surface steel, hot-dip galvanized after fabrication (HDGAF).

z

Optional Extended Surface Coil: Coils are available with selected rows finned at 3 to 5 fins per inch for wet/dry applications. The coil is hot-dip galvanized after fabrication (HDGAF).

z

Optional Stainless Steel Coil: Coils are available in Type 304L or 316L stainless steel for specialized applications.

All coils are designed for low pressure drop with sloping tubes for free drainage of fluid.

Fan Drive System The fan drive system provides the cooling air necessary to reject heat from the system to the atmosphere. Centrifugal fans, forwardly curved, are driven by matched V-belts with taper lock sheaves.

... because temperature matters

Closed Circuit Cooling Towers

z

Standard Construction: Steel panels and structural elements are constructed of Z600 heavy-gauge hot-dip galvanized steel protected with the Baltiplus Corrosion Protection on the outside of the unit.

VFL - C 8

VFL

Baltiguard® Drive System The BALTIGUARD® Drive System consists of two standard single-speed fan motors and drive assemblies. One drive assembly is sized for full speed and load, and the other is sized for approximately 2/3 speed and consumes only 1/3 of the design kilowatt power. This configuration allows the system to be operated like a two-speed motor, but with the reserve capacity of a standby motor in the event of failure. As a minimum, approximately 70% capacity will be available from the low kilowatt motor, even on a design wet-bulb day. Controls and wiring are the same, as those Baltiguard® Drive System required for a two-speed, two-winding motor. Significant energy savings are achieved when operating at low speed during periods of reduced load and/or low wet-bulb temperatures.

Low Sound Operation The low sound levels generated by BAC Products with centrifugal fans make them suitable for most installations. For situations when one direction is particularly sound sensitive, the unit can be oriented so that the side opposite the air inlet faces the sound-sensitive direction. Units with centrifugal fans are also available with factory designed, tested and rated sound attenuation for both the air inlet and discharge. Note: For more information, please refer to the section “Technical Resources, Sound Reduction Options”.

Remote Sump Execution

Sound Attenuation at Air Inlet and Discharge

The use of an auxiliary sump within a heated space is the most satisfactory way to protect sump water from freezing. When the circulating pump is shut off, all the water in the water distribution, in suspension and in the sump will drain freely to the auxiliary sump. Note: For detailed information on the calculation of the remote sump tank, please refer to the section "Technical Resources, Selection of Remote Sump Tank".

Baltimore Aircoil

VFL - C 9

Accessories Electric Water Level Control Package

Extended Lubrication Lines Extended lubrication lines with grease fittings are available for lubrication of the fan shaft bearings. Electric Water Level Control Package

Basin Heaters Units exposed to below freezing ambient temperatures require protection to prevent freezing of the water in the cold water basin when the unit is idle. Factory-installed heaters, which maintain the water temperature at 4°C, are a simple and inexpensive way of providing such protection. The heater package includes the heaters, a thermostat and a low level cut out switch to protect the heaters if the water level is too low. Standard electric heaters are selected for -18°C ambient temperature.

Model No. VFL

Heaters -18°C (kW)

VFL 24X

1x3

VFL 36X

1x4

VFL 48X

1x5

VFL 72X

2x4

VFL 96X

2x5

Plume Abatement Coil The use of plume abatement coils is recommended to reduce significantly the formation of visible plume during wet operation and extend the dry operation capability of the closed circuit cooling tower. The combination of discharge air reheating and extended dry operation minimises plume formation during weather conditions with high relative humidity. Plume abatement coils are also an effective way to save water and water treatment costs. Note: For more information, please refer to the section “Technical Resources, Plume Abatement”.

Plume Abatement Coil

... because temperature matters

Closed Circuit Cooling Towers

The electric water level control replaces the standard mechanical make-up valve when a more precise water level control is required. This package consists of a float switch mounted in the basin and a solenoid activated valve in the makeup water line. The valve is slow closing to minimize water hammer.

VFL - C 10

Capacity Control Dampers Modulating capacity control dampers are available to provide better leaving water temperature control than can be obtained from fan cycling alone. Fan discharge dampers consist of a single airfoil type damper blade located in the discharge of each fan housing. A standard electrical control package for dampers is available from BAC.

VFL

Basin Sweeper Piping Basin sweeper piping provides an effective method of preventing sediment from collecting in the cold water basin of the unit. A complete piping system, including nozzles, is provided in the unit basin for connection to side stream filtration equipment. Note: For more information, please refer to the section "Technical Resources, Filtration".

Discharge Hoods Discharge hoods reduce the risk of re-circulation in tight enclosures by increasing discharge air velocity, and can be used to elevate the unit discharge above adjacent walls to comply with layout guidelines.

Discharge Hoods with Positive Closure Dampers BAC offers a full line of standard discharge hoods with and without positive closure dampers that are built, tested, and rated specifically for all Series V Closed Circuit Cooling Towers. The tapered hoods are designed to increase the discharge air velocity to avoid recirculation in extremely tight enclosures. Straight or tapered hoods can be used to elevate the unit discharge above adjacent walls. A larger fanmotor may be necessary when this option is provided. For details of hoods furnished with positive closure dampers see section Engineering Data – Heat Loss Data.

Baltimore Aircoil

Positive Closure Damper Section

VFL - C 11

Engineering Data REMARK: Do not use for construction. Refer to factory certified dimensions & weights. This brochure includes data current at time of publication, which should be reconfirmed at the time of purchase. In the interest of product improvement, specifications, weights and dimensions are subject to change without notice. Up-to-date engineering data and more can be found at www.BaltimoreAircoil.com.

VFL 24 X - VFL 48 X

Model No. VFL

Operating Weight (kg)

Shipping Weight (kg)

Heaviest Section (kg)

H (mm)

L (mm)

L2 (mm)

W (mm)

Air Flow (m3/s)

Fan Motor (kW)

Spray Water Flow (l/s)

Pump Motor (kW)

Coil Volume (L)

VFL 241-H VFL 242-H VFL 242-J VFL 243-J

1950 2220 2230 2470

1280 1460 1490 1670

1280 1460 1490 1670

1855 2015 2015 2230

3350 3350 3350 3350

1820 1820 1820 1820

1250 1250 1250 1250

7,6 7,4 8,1 7,9

4 4 5,5 5,5

5,9 5,9 5,9 5,9

0,55 0,55 0,55 0,55

(1x) 176 (1x) 229 (1x) 229 (1x) 282

VFL 361-L VFL 361-M VFL 362-M VFL 363-K VFL 363-M

2800 2810 3130 3470 3540

1810 1820 2090 2280 2350

1810 1820 2090 2280 2350

1855 1855 2090 2350 2350

4560 4560 4560 4560 4560

2730 2730 2730 2730 2730

1250 1250 1250 1250 1250

12,7 13,8 13,4 10,8 13,0

11 15 15 7,5 15

9,0 9,0 9,0 9,0 9,0

0,75 0,75 0,75 0,75 0,75

(1x) 258 (1x) 258 (1x) 338 (1x) 418 (1x) 418

VFL 481-M VFL 482-L VFL 483-L VFL 483-M VFL 484-M

3490 3930 4390 4400 4860

2170 2490 2830 2840 3170

2170 2490 2830 2840 3170

1855 2090 2350 2350 2560

5480 5480 5480 5480 5480

3650 3650 3650 3650 3650

1250 1250 1250 1250 1250

15,1 13,6 13,4 14,6 14,3

15 11 11 15 15

12,1 12,1 12,1 12,1 12,1

1,1 1,1 1,1 1,1 1,1

(1x) 341 (1x) 448 (1x) 556 (1x) 556 (1x) 664

... because temperature matters

Closed Circuit Cooling Towers

1. Fluid in ND100; 2. Fluid Out ND100; 3.Access Door; 4. Make Up ND25; 5. Overflow ND50 for VFL 24X - VFL 36x and ND80 for VFL 48X; 6. Drain ND50; 7. Vent ND15.

VFL - C 12

VFL

VFL 72 X - VFL 96 X

1. Fluid in ND100; 2. Fluid Out ND100; 3.Access Door; 4. Make Up ND50; 5. Overflow ND80; 6. Drain ND50; 7. Vent ND15.

Model No. VFL

Operating Weight (kg)

Shipping Weight (kg)

Heaviest Section (kg)

H (mm)

L1 (mm)

L2 (mm)

W (mm)

Air Flow (m3/s)

Fan Motor (kW)

Spray Water Flow (l/s)

Pump Motor (kW)

Coil Volume (L)

VFL 721-L VFL 721-M VFL 721-O VFL 722-N VFL 722-O VFL 723-L VFL 723-O VFL 724-O

5150 5160 5190 5880 5900 6610 6650 7320

3150 3160 3190 3700 3720 4210 4250 4790

3150 3160 3190 3700 3720 4210 4250 4790

1855 1855 1855 2090 2090 2350 2350 2560

4560 4560 4560 4560 4560 4560 4560 4560

2730 2730 2730 2730 2730 2730 2730 2730

2400 2400 2400 2400 2400 2400 2400 2400

20,0 21,8 24,6 22,8 24,0 19,3 23,4 22,9

11 15 22 18,5 22 11 22 22

17,9 17,9 17,9 17,9 17,9 17,9 17,9 17,9

1,1 1,1 1,1 1,1 1,1 1,1 1,1 1,1

(2x) 258 (2x) 258 (2x) 258 (2x) 338 (2x) 338 (2x) 418 (2x) 418 (2x) 498

VFL 961-P VFL 962-N VFL 962-O VFL 962-P VFL 963-O VFL 963-P VFL 964-P

6520 7285 7310 7400 8210 8310 9300

3850 4360 4400 4500 5060 5160 5810

3850 4360 4400 4500 5080 5160 5810

1855 2090 2090 2090 2350 2350 2560

5480 5480 5480 5480 5480 5480 5480

3650 3650 3650 3650 3650 3650 3650

2400 2400 2400 2400 2400 2400 2400

28,7 24,5 25,9 28,3 25,6 27,9 27,4

30 18,5 22 30 22 30 30

24,2 24,2 24,2 24,2 24,2 24,2 24,2

2,2 2,2 2,2 2,2 2,2 2,2 2,2

(2x) 341 (2x) 448 (2x) 448 (2x) 448 (2x) 556 (2x) 556 (2x) 664

General Notes 1. All location dimensions for coil connections are approximate and should not be used for prefabrication of connecting piping. 2. If discharge hoods with positive closure dampers are furnished, see table in section Engineering Data – Straight Discharge Hood with PCD for added weight and height. 3. For external static pressure up to 125 Pa use next larger motor size. 4. For indoor applications of fluid coolers, the room may be used as a plenum with ductwork attached to the discharge only. If inlet ductwork is required, an enclosed fan section must be specified; consult your BAC Balticare representative for details.

5. Fan cycling results only in on-off operation. For additional steps of control, two-speed fan motors are available. More precise capacity control can be obtained with modulation fan discharge dampers or a BALTIGUARD® Drive System 6. Make up, overflow, suction, drain connections and access door can be provided on side opposite to that shown; consult your BAC Balticare representative. 7. Shipping/operating weights indicated are for units without accessories such as sound attenuators, discharge hoods, plume abatement coils, etc. Consult factory certified prints to obtain weight additions and the heaviest section to be lifted.

Baltimore Aircoil

VFL - C 13

Sound Attenuation HS Horizontal Intake Sound Attenuation

HD Horizontal Intake Sound Attenuation

1.Discharge attenuator, 2. Access Door, 3. Intake Attenuator; W & H = Unit Dimensions (See Engineering Data).

... because temperature matters

Closed Circuit Cooling Towers

1.Discharge attenuator, 2. Access Door, 3. Intake Attenuator; W & H = Unit Dimensions (See Engineering Data).

VFL - C 14

VFL

VS Vertical Intake Sound Attenuation

1.Discharge attenuator, 2. Access Door, 3. Intake Attenuator, 4. Plenum; W & H = Unit Dimensions (See Engineering Data).

Dimensions (mm) Model No VFL

L2

Maximum Weight (kg) L1

Intake Attenuator + Solid Bottom

Discharge Attenuator

Total

HS

HD

VS

HS,HD,VS

HS

HD

HS

HD

HS

HD

VS

VFL 24X

2390

3125

2010

1820

460

655

215

235

675

890

725

VFL 36X

2640

3375

2010

2730

465

660

295

315

760

975

830

VFL 48X

2640

3375

2010

3650

465

660

365

385

830

1045

915

VFL 72X

2640

3375

2010

2730

665

980

465

500

1130

1480

1205

VFL 96X

2640

3375

2010

3650

665

980

565

605

1230

1585

1310

Note: All units with HS, VS or HD attenuators ship in 2 pieces.

Baltimore Aircoil

VFL - C 15

Heat Loss Data Discharge Hoods with Positive Closure Dampers (PCD’s)

Heat Loss Data (kW) (1)

Model No. Minimum Flow (l/s)

L

W

H

6,3 6,7 6,7 7,1

1820

1200

865

4,1

16,0 16,0 19,1 21,6 21,6

9,8 9,8 10,4 11,0 11,0

2730

1200

865

4,1

23,0 27,2 30,5 30,5 33,8

13,8 14,5 15,2 15,2 15,9

3650

1200

865

7,9

40,1 40,1 40,1 46,4 46,4 51,5 51,5 56,6

17,8 17,8 17,8 18,6 18,6 19,3 19,3 20,0

2730

2400

865

7,9

47,9 56,3 56,3 56,3 63,0 63,0 69,7

20,1 21,0 21,0 21,0 21,9 21,9 23,8

3650

2400

865

Standard Unit

Unit with Discharge Hood and PCD’s

4,1

10,6 12,7 12,7 14,4

VFL VFL 241-H VFL 242-H VFL 242-J VFL 243-J VFL 361-L VFL 361-M VFL 362-M VFL 363-K VFL 363-M VFL 481-M VFL 482-L VFL 483-L VFL 483-M VFL 484-M VFL 721-L VFL 721-M VFL 721-O VFL 722-N VFL 722-O VFL 723-L VFL 723-O VFL 724-O VFL 961-P VFL 962-N VFL 962-O VFL 962-P VFL 963-O VFL 963-P VFL 964-P

(1) Heat loss data based on 10°C water and –14°C ambient temperature with 20 m/s wind velocity (fans and pump off).

Remote Sump Data Refer to the "Technical Resources" section "Selection of Remote Sump" for Remote Sump Data.

... because temperature matters

Closed Circuit Cooling Towers

1. Access Door.

VFL - C 16

Structural Support REMARK: Do not use for construction. Refer to factory certified dimensions & weights. This brochure includes data current at time of publication, which should be reconfirmed at the time of purchase. In the interest of product improvement, specifications, weights and dimensions are subject to change without notice. Up-to-date engineering data and more can be found at www.BaltimoreAircoil.com.

VFL

The recommended support arrangement for units consists of parallel I-beams running the full length of the unit, spaced as shown in the following drawing. Besides providing adequate support, the steel also serves to raise the unit above any solid foundation to ensure access to the bottom of the unit. To support units in an alternate steel support arrangement, consult your BAC Balticare Representative.

Units with and without Sound Attenuation Model No. VFL

A (mm)

B (mm)

Maximum Allowable Beam Deflection (mm)

VFL 24X VFL 36X VFL 48X

2426 3334 4253

1194 1194 1194

10 13 13

VFL 72X VFL 96X

3334 4253

2344 2344

13 13

1. (4) Ø 22 mm mounting holes; 2. Support Beams; 3. Fan Side; 4. Outline of Unit; 5. Outline of Attenuator “HS” (optional); 6. Outline of Attenuator “HD” (optional).

Notes: 1. The recommended support arrangement for these units consists of two parallel I-beams extending the full length of the unit. Supports and anchor bolts are to be designed and furnished by others. 2. All supporting beams are to be flush and level at top and must be oriented relative to gage line as shown. 3. Recommended design loads for each unit support beam should be 70% of the total unit operating weight applied as a uniform load to each of the unit beams. Beams should be designed in

accordance with standard structural practice. For the maximum allowable deflection of beams under the unit refer to above table. 4. All mounting holes have a diameter of 22 mm at the locations shown. 5. If vibration isolators are used, a rail or channel must be provided between the unit and the isolators to provide continuous unit support. Additionally the support beams must be designed to accommodate the overall length and mounting hole location of the isolators that may differ from those of the unit. Refer to vibration isolator drawings for these data.

Baltimore Aircoil

VFL - C 17

Engineering Specifications 1.0 Closed Circuit Cooling Tower

1.2. Thermal Capacity (water as heat transfer fluid): The closedcircuit cooling tower(s) shall be warranted by the manufacturer to cool ______l/s of _______ water from ____°C to ____°C at ____°C entering wet-bulb temperature. (Alternate1.2.) Thermal Capacity (aqueous glycol solution as heat transfer fluid): The closed circuit cooling tower(s) shall be warranted by the manufacturer to cool ________l/s of _____% by volume ethylene/propylene glycol solution from ______°C to _____°C at _____°C entering wet-bulb temperature. Coil pressure drop shall not exceed ________bar. 1.3. Corrosion Resistant Construction: Unless otherwise noted in this specification, all steel panels and structural members shall be constructed of heavy-gauge Z600 metric hot-dip galvanized steel, with all sheared edges given a protective coating of zinc-rich

compound and the exterior protected with the Baltiplus Corrosion Protection. (Alternate1.3.) Corrosion Resistant Construction: Unless otherwise noted in this specification, all steel panels and structural members shall be protected with the BALTIBOND® Corrosion Protection System. The system shall consist of Z600 metric hot-dip galvanized steel prepared in a four-step (clean, pre-treat, rinse, and dry) process with an electrostatically sprayed, thermosetting hybrid polymer fuse-bonded to the substrate during a thermally activated curing stage and monitored by a 23-step quality assurance program. (Alternate 1.3) Corrosion Resistant Construction: Unless otherwise noted in this specification, all steel panels and structural members shall be constructed of Type 304 or 316 stainless steel and assembled with stainless steel nut and bolt fasteners. 1.4. Quality Assurance: The closed circuit cooling tower manufacturer shall have a management system certified by an accredited registrar as complying with the requirements of ISO9001:2000 to ensure consistent quality of its products and services. 1.5. Warranty: The manufacturer’s standard equipment warranty shall be for a period of not less than one year from date of startup or eighteen months from date of shipment, whichever occurs first.

2.0 Construction Details 2.1.Tower Structure: The closed circuit cooling tower shall be constructed of heavy-gauge steel utilizing double-brake flanges for maximum strength and rigidity and reliable sealing of water-tight joints. All sheared edges shall be protected with a coating of zinc-rich compound. 2.2. Casing Assembly: The closed circuit cooling tower shall include a coil casing section consisting of a serpentine coil, spray water distribution system, and drift eliminators, as indicated by the manufacturer. Plastic drift eliminators shall be removable in easily handled sections. They shall incorporate a minimum of three changes in air direction. 2.3. Coil Assembly: The cooling coil shall be fabricated of continuous lengths of all prime surface steel at the manufacturer’s own facility, and hot-dip galvanized after fabrication. The cooling coil shall be pneumatically tested at 15 bar. The cooling coil shall be designed for low pressure drop with sloping tubes for free drainage of fluid and shall be compliant to PED. Maximum allowable working pressure shall be 10 bar. 2.4. Water Distribution System: Water shall be distributed evenly over the coil at a minimum flow rate of 3,1 l/s/m to ensure complete wetting of the coil at all times by large-diameter, non-clog, plastic 360° distribution nozzles, spaced across the coil face area in PVC spray branches by snap-in rubber grommets, allowing quick removal of individual nozzles or complete branches for cleaning or flushing.

Nozzles shall utilize a two-stage diffusion pattern to provide overlapping, umbrella spray patterns that create multiple intersection points with adjacent nozzles. 2.5. Spray Pump System: The closed circuit cooling tower shall include a close-coupled, bronze-fitted centrifugal pump equipped with a mechanical seal, mounted on the basin and piped to the suction strainer and water distribution system. It shall be installed so that it can be drained when the basin is drained. The pump assembly shall include a metering valve and bleed line to control the bleed rate from the pump discharge to the overflow connection. The pump motor shall be totally enclosed fan cooled (TEFC) type with IP 55 protection and class B insulation suitable for outdoor service, _____ kW, _______Volt, ________Hz, ______Phase. (Alternate 2.5.) Spray Pump System-Remote Sump: On installations requiring a remote sump, the closed circuit cooling tower shall be modified to accommodate the use of an independent basin and pump (both by others) for recirculating water. 2.6. Basin Assembly: The combination basin/fan section shall be constructed of heavy-gauge Z600 galvanized steel. The basin shall be provided with large area lift out strainers with perforated openings sized smaller than the water distribution nozzles and an anti-vortexing device to prevent air entrainment. The strainer and vortex device shall be constructed of the same material as the cold water basin to prevent dissimilar metal corrosion.

3.0 Mechanical Equipment 3.1. Fan System: The fans and motors shall be factory installed at the base of the unit in the dry entering air stream to provide greater reliability and ease of maintenance. The forwardly curved centrifugal fans shall be heavy-duty centrifugal flow types. Fan housings shall have curved inlet rings for efficient air entry and rectangular discharge cowls shall extend into the basin to increase fan efficiency and prevent water from entering the fans. Fans shall be mounted on a steel fan shaft supported by heavy-duty self-aligning, relubricatable ball bearings with cast iron housings and designed for a minimum L10 life of 40 000 hours (280 000 hrs average life). The fan shaft shall be protected with a two-part epoxy coating for corrosion protection.

3.2. Fan Motor/Drive System: Fan motor(s) shall be totally enclosed fan cooled (TEFC), IP-55, class F, selected for _____Pa static pressure. Fan motor(s) shall be suitable for _____ volts, ____ phase, ____ Hz electrical service and shall be mounted on an easily adjusted, heavy-duty motor base. V-belt drives and all moving parts are protected with removable screens. (Alternate 3.2.) Baltiguard® Fan System: Two single speed fan motors, one sized for full speed and load, the other sized for 2/3 speed and approximately 1/3 of full load kW shall be provided in each cell for capacity control and standby protection from drive or motor failure. Two-speed motor(s) is not an acceptable alternative.

... because temperature matters

Closed Circuit Cooling Towers

1.0 General: Furnish and install ____factory assembled, forced draft, centrifugal fan, closed circuit cooling tower(s) with vertical air discharge, conforming in all aspects to the specifications and schedules as shown on the plans. Overall dimensions shall not exceed approximately ____mm long x ____mm wide x ____ mm high. The total connected fan kW shall not exceed ____kW. The total connected pump kW shall not exceed ____kW. The closed circuit cooling tower(s) shall be Baltimore Aircoil Company Model(s) ________________.

VFL - C 18

4.0 Drift Eliminators 4.1 Drift Eliminators: Eliminators shall be constructed of specially formulated plastic material and be removable in easily handled

sections. They shall have a minimum of three changes in air direction.

5.0 Access 5.1 Basin Access: Circular access doors shall be provided for easy access to the make-up water assembly and suction strainer for

routine maintenance.

VFL

6.0 Sound 5.1 Sound Level: To maintain the quality of the local environment, the maximum sound pressure levels (dB) measured 15 m from the

Location

63

125

250

cooling tower operating at full fan speed shall not exceed the sound levels detailed below.

500

Discharge Air Inlet End Back

Baltimore Aircoil

1000

2000

4000

8000

dB(A)

FXV - C 1

FXV

Closed Circuit Cooling Towers

FXV Closed Circuit Cooling Tower ......................................................... C2 Benefits ....................................................................................................... C4 Construction Details .................................................................................. C6 Custom Features and Options .................................................................. C8 Accessories ............................................................................................... C11 Engineering Data FXV Models .............................................................. C13 Structural Support FXV Models ............................................................ C18 Engineering Data FXV-D Models .......................................................... C19 Structural Support FXV-D Models ........................................................ C22 Engineering Specifications ..................................................................... C23

Closed Circuit Cooling Towers

Product Detail

FXV - C 2

FXV Closed Circuit Cooling Tower Capacity Single Cell Capacity: FXV: 3-149 l/s

FXV

FXV-D: up to 300 l/s

General Description FXV Closed Circuit Cooling Towers deliver fully rated thermal performance over a wide range of flow and temperature requirements. Standard design features satisfy today’s environmental concerns, minimize installation costs, maximize year-round operating reliability, and simplify maintenance requirements.

Key Features z

Low Energy Consumption

z

Low installed cost

z

Easy maintenance

z

Application flexibility

z

Reliable year-round operation

z

Long service life

Baltimore Aircoil

FXV - C 3

Closed Circuit Cooling Towers

... because temperature matters

FXV - C 4

Benefits Low Energy Consumption

FXV

z

z

Evaporative Cooling Equipment minimizes the energy consumption of the entire system because it provides lower operating temperatures. The owner saves money while conserving natural resources and reducing environmental impact. FXV provides heat rejection at the lowest possible energy input and maintenance requirements via: - High efficiency, low kW axial fans - Closed loop cooling, which minimizes process fouling - Patented combined flow technology, which reduces evaporation directly off the coil, minimizing the potential for scaling and fouling - Parallel flow of air and spray water, which eliminates scale-promoting dry spots - Multiple Fan Motor System: independent fan motor and drive assembly per fan, which allows for extra steps of capacity control.

Easy Maintenance z

z

z

Access - Hinged access doors provide easy access to the unit interior. In addition, all FXV models are provided with an internal walkway as standard. An internal walkway is available as an option on FXV-D models. Spacious Interior – Provides easy access to the cold water basin, drift eliminators, fan drive system and heat transfer coil. Access to Spray Distribution – Parallel flow of air and spray water over the coil allows for inspection and access to the top of the coil during full operation.

Large, hinged access door

Baltimore Aircoil

Spray Distribution System

FXV - C 5

Low Installed Cost z

z

Support — All models mount directly on parallel I-beams and ship complete with motors and drives factory-installed and aligned. Modular Design —Units ship in multiple sections to minimize the size and weight of the heaviest lift, allowing for the use of smaller, less costly cranes.

Application Flexibility

z

z

Difficult thermal duties - The combined flow design is ideal for applications requiring a close approach and/or large range. Replacement applications – Single air inlet models are designed to mount directly on existing support steel of both crossflow and counterflow units. Highest capacity in the industry – FXV-D models offer the highest single cell capacity of any evaporative closed circuit cooling tower in the industry. Projects benefit from fewer required cells, lower overall fan kW, and fewer piping connections.

Reliable Year-Round Operation z

z

Belt Drive System utilizes special corrosion-resistant materials of construction and state-ofthe-art technology to ensure ease of maintenance and reliable year-round performance. Combined Inlet Shields prevent biological growth from sunlight, act as a filter for air borne impurities and debris and eliminate water splash out.

Easy Removable Fill (D-models only) The fill removal system allows nesting the fill in place for cleaning and replacement. The fill section can easily be reached after removal of the Combined Inlet Shields / drift eliminators. Telescopic fill support allow for complete fill removal.

Long Service Life z

Materials of Construction – Various materials are available to meet the corrosion resistance, unit operating life, and budgetary requirements of any project.

Note: For more information, please refer to the section “Technical Resources, Materials of Construction”.

... because temperature matters

Closed Circuit Cooling Towers

z

FXV - C 6

Construction Details FXV Models

FXV

.

1. Heavy-Duty Construction z Z600 hot-dip galvanized steel panels

2. Fan Drive System

6. BACross® Wet Deck Surface with Integral Drift Eliminators (Not Shown) z Plastic material

z Premium quality belts

z Impervious to rot, decay and biological attack

z Corrosion resistant sheaves

z Designed and manufactured by BAC

z Heavy-duty bearings z Adapted fan motor for operation in saturated conditions.

3. Low kW Axial Fan

7. Combined Inlet Shields z Corrosion Resistant z Easily removable z UV resistant plastic material

z Quiet operation z High Efficiency

8. Cold Water Basin

z Corrosion resistant aluminum

4. Water Distribution System

z Sloped cold water basin for easy cleaning z Suction strainer with anti-vortex hood

z Visible and accessible during operation

z Adjustable water make-up assembly from air inlet side

z Overlapping spray patterns ensure proper water coverage

z Integral internal walkway as standard

z Large orifice, non-clog nozzles

5. Coil Section (Not Shown)

9. Recirculating Spray Water Pump z Close coupled, bronze fitted centrifugal pump

z Continuous serpentine, steel tubing

z Totally enclosed fan cooled (TEFC) motor

z Hot-dip galvanized after fabrication (HDGAF)

z Bleed line with metering valve installed from pump discharge

to overflow

z Sloped tubes for free drainage of fluid

10. Hinged Access Doors z Designed for maximum 10 bar operating pressure according

to PED

z Inward swinging door

Baltimore Aircoil

FXV - C 7

FXV-D Models

z Designed for maximum 10 bar operating pressure according

to PED

2. FRP Casing Panels z Corrosion resistant

7. BACrossII Wet Deck Surface with Integral Drift Eliminators

z Maintenance free

z Plastic material

z UV-resistant finish

z Impervious to rot, decay and biological attack

3. Fan Drive System

z Designed and manufactured by BAC

z Premium quality belts

8. Combined Inlet Shields

z Corrosion resistant sheaves

z Corrosion Resistant

z Heavy-duty bearings

z Easily removable

z Adapted fan motor for operation in saturated conditions.

z UV resistant plastic material

4. Low kW Axial Fan

9. Cold Water Basin

z Quiet operation

z Sloped cold water basin for easy cleaning

z High Efficiency

z Suction strainer with anti-vortex hood

z Corrosion resistant aluminum

z Adjustable water make-up assembly from inside the unit

5. Water Distribution System

10. Integral Recirculating Spray Water Pumps (Not Shown)

z Visible and accessible during operation

z Close coupled, bronze fitted centrifugal pump

z Overlapping spray patterns ensure proper water coverage

z Totally enclosed fan cooled (TEFC) motor

z Large orifice, non-clog nozzles

z Bleed line with metering valve installed from pump discharge

to overflow

6. Coil Section z Continuous serpentine, steel tubing

11. Hinged Access Doors (Not Shown)

z Hot-dip galvanized after fabrication (HDGAF)

z Inward swinging door on each end wall

... because temperature matters

Closed Circuit Cooling Towers

z Sloped tubes for free drainage of fluid

1. Heavy-Duty Construction z Heavy-gauge Z600 galvanized steel frame

FXV - C 8

Custom Features and Options Construction Options z

FXV

z

Standard Construction: Steel panels and structural elements are constructed of Z600 heavy-gauge hot-dip galvanized steel protected with the Baltiplus Corrosion Protection on the outside of the unit. Optional BALTIBOND® Corrosion Protection System: The BALTIBOND® Corrosion Protection System, a hybrid polymer coating used to extend equipment life, is applied before assembly to all hot-dip galvanized steel components of the unit.

z

Optional Stainless Steel Construction: Steel panels and structural elements are constructed of stainless steel either type 304 or 316.

z

Optional Water-Contact Stainless Steel Cold Water Basin: A cost-effective alternative to an all stainless steel unit. The critical components in the cold water basin and the cold water basin itself are provided in stainless steel. The remaining components are protected with the BALTIBOND® Corrosion Protection System.

Note: See section Technical Resources, Material of Construction for more details on the materials described above.

Prime Surface Coil Configurations z

Standard Serpentine Coil: The standard cooling coil is constructed of continuous lengths of all prime surface steel, hot-dip galvanized (outside surface) after fabrication (HDGAF). The coil is designed for low pressure drop with sloping tubes for free drainage of fluid. Each coil is pneumatically tested at 15 bar and PED compliant.

z

Stainless Steel Coil: Coils are available in Type 304L and 316L stainless steel for specialized applications. The coil is designed for low pressure drop with sloping tubes for free drainage of fluid. Each coil is pneumatically tested at 15 bar and is PED compliant.

Hot Dip Galvanised Coil

Multiple Fan Drive System (not on FXV-D Models) All FXV-models (except FXV-D) are standard equipped with the multiple fan motor system. This system consists of an independent fan motor and drive assembly per fan with a plenum partition to allow independent operation of each fan. This standard feature provides 2 steps of capacity control on dual fan units and 3 steps of capacity control on triple fan units, as illustrated below.

Individual Motor and Drive on each Fan

Baltimore Aircoil

Extra Steps of Capacity Control

FXV - C 9

Low Sound Operation The low sound levels generated by Series 1500 Units, thanks to the use of high efficiency low noise fans as standard, make them suitable for installation in most environments. For very sound sensitive installations all models are also available with a “Whisper Quiet” sound fan option that significantly reduces the sound levels generated from the tower with minimal impact on thermal performance. For extremely sound sensitive installations, factory designed, tested and rated sound attenuation is available for both the air inlet and discharge. Note: For more information, please refer to the section “Technical Resources, Sound Reduction Options”.

The D-models are available with a gear drive system with external TEFC motor and a non-corrosive carbonfiber composite drive shaft with stainless steel hubs is selected with a 2,0 service factor. The motor and drive shaft ship separately for easy field installation.

Gear Drive System, Closed-Coupled Motor (FXV-D models only) The D-Models are available with a close-coupled gear drive system. Both the gear drive and couplings are selected with a 2,0 service factor. Gear construction includes a nickel-alloy steel shaft, casehardened gears, self-lubrication, and a single piece, gray iron housing. This drive system ships completely installed and aligned.

Gear Drive System, close-coupled motor

Combined Inlet Shields Combined Inlet shields prevent biological growth from sunlight, act as a filter for air borne impurities and debris and eliminate water splash out.

Remote Sump Execution The use of an auxiliary sump within a heated space is the most satisfactory way to protect sump water from freezing. When the circulating pump is shut off, all the water in the water distribution, in suspension and in the sump will drain freely to the auxiliary sump. Note: For detailed information on the calculation of the remote sump tank, please refer to the section "Technical Resources, Selection of Remote Sump Tank".

Combined Inlet Shields

... because temperature matters

Closed Circuit Cooling Towers

Gear Drive System, Externally Mounted Motor (FXV-D models only)

FXV - C 10

FXV

Removable Bundled Fill (only FXV-models) For installations where it is necessary or recommended to remove the wet deck surface for more thorough cleaning and disinfection, removable bundled fill is available. The fill bundles can be easily lifted and handled by one person and therefore provide a simple and secure method of removing and installing. The bundles can be dismantled and sheet by sheet can be removed for inspection and cleaning of both sides. After cleaning the sheets can be rebundled and re-installed.

Baltimore Aircoil

Easy Removable Fill Bundles

FXV - C 11

Accessories External Service Platform with Ladder, Safety Cage and Handrails

Note: Top air inlet screens are recommended with this option.

Internal Ladder For access to the motor and drive assemblies internal ladders are available on all models.

Internal Service Platforms

External Service Platform, Ladder and Safety Cage

For access to the motor and drive assemblies on single air inlet models FXV-54x through FXV-66x and all FXV-D models, an internal ladder and upper service platform with handrails is available.

Basin Heaters Units exposed to below freezing ambient temperatures require protection to prevent freezing of the water in the cold water basin when the unit is idle. Factory-installed heaters, which maintain the water temperature at 4°C, are a simple and inexpensive way of providing such protection. The heater package includes the heaters, a thermostat and a low level cut out switch to protect the heaters if the water level is too low. Standard electric heaters are selected for -18°C ambient temperature. Model No. FXV

Heaters -18°C (kW)

FXV 422 FXV 423 FXV 424

1x4 1x4 1x4

FXV 432 FXV 433

1x6 1x6

FXV 442 FXV 443 FXV 444

1x6 1x6 1x6

FXV Q440 FXV Q441

1x6 1x6

FXV 542 FXV 543 FXV 544

1x8 1x8 1x8

FXV Q540 FXV Q541

1x8 1x8

FXV 561 FXV 562

2x6 2x6

FXV Q560 FXV Q561

2x6 2x6

FXV 642 FXV 643 FXV 644

2x6 2x6 2x6

FXV 661 FXV 662

2x8 2x8

FXV Q661

2x8

FXV-D 288-x

2 x 12

FXV-D 364-x

2 x 14

... because temperature matters

Closed Circuit Cooling Towers

In the event the owner requires easy access to the top of the unit, the unit can be furnished with a platform and ladders extending from the base of the unit to the platform, as well as safety cages, and handrail packages.

FXV - C 12

Top Air Inlet Screens The screens protect the air inlet side above the coil section only. Top air inlet screens are always in Baltibond Corrosion® Protection System.

FXV

Basin Sweeper Piping Basin sweeper piping provides an effective method of preventing sediment from collecting in the cold water basin of the unit. A complete piping system, including nozzles, is provided in the unit basin for connection to side stream filtration equipment. Note: For more information, please refer to the section "Technical Resources, Filtration".

Vibration Cut-out Switch A factory-mounted vibration cut-out switch is available to effectively protect against equipment Basin Sweeper Piping failure due to excessive vibration of the mechanical equipment system. BAC can provide a vibration cut-out switch in an IP65 enclosure to ensure reliable protection.

Extended Lubrication Lines Extended lubrication lines with grease fittings are available for lubrication of the fan shaft bearings.

Electric Water Level Control Package The electric water level control replaces the standard mechanical make-up valve when a more precise water level control is required. This package consists of a float switch mounted in the basin and a solenoid activated valve in the makeup water line. The valve is slow closing to minimize water hammer. Extended Lubrication Lines

Mechanical Equipment Removal System (Only on FXV-D Models) The mechanical equipment removal system is a lightweight, easy to install system for removal and installation of fan motor or gearbox. (motors up to 22kW)

Positive Closure Damper (PCD) Hoods The FXV’s innovative design results in a low heat loss when the unit is idle. When additional heat loss protection is desired, coil air intake hoods with factory mounted PCD’s and damper actuators can be provided.

Baltimore Aircoil

Mechanical Equipment Removal System

FXV - C 13

Engineering Data FXV Models REMARK: Do not use for construction. Refer to factory certified dimensions & weights. This brochure includes data current at time of publication, which should be reconfirmed at the time of purchase. In the interest of product improvement, specifications, weights and dimensions are subject to change without notice. Up-to-date engineering data and more can be found at www.BaltimoreAircoil.com.

1. Fluid in; 2. Fluid out; 3. Make-Up ND15; 4. Overflow ND80; 5. Drain ND50; 6. Access door; 7. Vent ND15.

(mm)

Air Flow (m3/s)

Fan Motor (kW)

Spray Water Flow (l/s)

1861 1861 1861 1861 1861

2385 2385 2385 2385 2385

13,0 14,5 16,0 14,3 15,8

(1x) 4,0 (1x) 5,5 (1x) 7,5 (1x) 5,5 (1x) 7,5

12,0 12,0 12,0 12,0 12,0

1,1 1,1 1,1 1,1 1,1

(1x) 226 (1x) 226 (1x) 226 (1x) 278 (1x) 278

(1x) ND 100 (1x) ND 100 (1x) ND 100 (1x) ND 100 (1x) ND 100

3980 3980 3980

2775 2775 2775

2385 2385 2385

23,4 26,0 25,6

(2x) 4,0 (2x) 5,5 (2x) 5,5

18,3 18,3 18,3

2,2 2,2 2,2

(1x) 337 (1x) 337 (1x) 418

(1x) ND 100 (1x) ND 100 (1x) ND 100

2590 2610 2620 2910 2920 3210

3980 3980 3980 3980 3980 3980

3690 3690 3690 3690 3690 3690

2385 2385 2385 2385 2385 2385

26,2 29,2 32,4 28,8 31,9 31,7

(2x) 4,0 (2x) 5,5 (2x) 7,5 (2x) 5,5 (2x) 7,5 (2x) 7,5

31,5 31,5 31,5 31,5 31,5 31,5

2,2 2,2 2,2 2,2 2,2 2,2

(1x) 452 (1x) 452 (1x) 452 (1x) 560 (1x) 560 (1x) 669

(1x) ND 100 (1x) ND 100 (1x) ND 100 (1x) ND 100 (1x) ND 100 (1x) ND 100

2590 2610 3200

3980 3980 3980

3690 3690 3690

2385 2385 2385

26,2 29,1 28,5

(2x) 4,0 (2x) 5,5 (2x) 5,5

31,5 31,5 31,5

2,2 2,2 2,2

(1x) 452 (1x) 452 (1x) 669

(1x) ND 150 (1x) ND 150 (1x) ND 150

Model No. FXV

Operating Weight (kg)

Shipping Weight (kg)

Heaviest Section (kg)

H

L

W

(mm)

(mm)

FXV 422-H FXV 422-J FXV 422-K FXV 423-J FXV 423-K

3570 3590 3600 3800 3810

2350 2370 2380 2520 2530

1440 1450 1460 1600 1610

3980 3980 3980 3980 3980

FXV 432-K FXV 432-L FXV 433-L

5250 5260 5580

3390 3410 3640

2150 2160 2390

FXV 442-K FXV 442-L FXV 442-M FXV 443-L FXV 443-M FXV 444-M

6640 6660 6670 7090 7100 7520

4150 4180 4190 4480 4490 4780

FXV Q440-K FXV Q440-L FXV Q441-L

6640 6660 7510

4150 4180 4770

Pump Inlet/Outlet Coil Volume Motor Coil Conn. (L) (kW) (mm)

... because temperature matters

Closed Circuit Cooling Towers

FXV 42x - FXV 44x

FXV - C 14

FXV

FXV 54x - FXV 56x

1. Fluid in; 2. Fluid out; 3. Make-Up ND25; 4. Overflow ND80; 5. Drain ND50; 6. Access door; 7. Vent ND15.

(mm)

Air Flow (m3/s)

Fan Motor (kW)

Spray Water Flow (l/s)

Pump Motor (kW)

Coil Volume (L)

Inlet/Outlet Coil Conn. (mm)

3690 3690 3690 3690 3690 3690

2985 2985 2985 2985 2985 2985

35,1 38,9 41,3 38,6 43,8 43,5

(2x) 5,5 (2x) 7,5 (2x) 9,0 (2x) 7,5 (2x) 11 (2x) 11

45,1 45,1 45,1 45,1 45,1 45,1

4 4 4 4 4 4

(1x) 671 (1x) 671 (1x) 671 (1x) 832 (1x) 832 (1x) 993

(1x) ND 100 (1x) ND 100 (1x) ND 100 (1x) ND 100 (1x) ND 100 (1x) ND 100

4790 4790 4790

3690 3690 3690

2985 2985 2985

38,9 44,2 43,5

(2x) 7,5 (2x) 11 (2x) 11

45,1 45,1 45,1

4 4 4

(1x) 671 (1x) 671 (1x) 993

(1x) ND 150 (1x) ND 150 (1x) ND 150

4020 4090 4680 4740

4930 4930 4930 4930

5520 5520 5520 5520

2985 2985 2985 2985

59,3 67,4 58,9 66,9

(3x) 7,5 (3x) 11 (3x) 7,5 (3x) 11

56,8 56,8 56,8 56,8

5,5 5,5 5,5 5,5

(1x) 762 (1x) 762 (1x) 1007 (1x) 1007

(1x) ND 100 (1x) ND 100 (1x) ND 100 (1x) ND 100

4670 4740 6010 6090

4930 4930 4930 4930

5520 5520 5520 5520

2985 2985 2985 2985

53,0 66,8 52,3 65,9

(3x) 5,5 (3x) 11 (3x) 5,5 (3x) 11

56,8 56,8 56,8 56,8

5,5 5,5 5,5 5,5

(1x) 1007 (1x) 1007 (1x) 1562 (1x) 1562

(1x) ND 150 (1x) ND 150 (1x) ND 150 (1x) ND 150

Model No. FXV

Operating Weight (kg)

Shipping Weight (kg)

Heaviest Section (kg)

H

L

W

(mm)

(mm)

FXV 542-L FXV 542-M FXV 542-N FXV 543-M FXV 543-O FXV 544-O

7960 7970 8000 8600 8630 9260

4960 4970 5000 5410 5450 5890

3240 3250 3270 3690 3720 4160

4790 4790 4790 4790 4790 4790

FXV Q540-M FXV Q540-O FXV Q541-O

7970 8000 9260

4970 5010 5890

3250 3280 4160

FXV 561-M FXV 561-O FXV 562-M FXV 562-O

10650 10710 11590 11650

6430 6490 7090 7150

FXV Q560-L FXV Q560-O FXV Q561-L FXV Q561-O

11580 11650 13470 13550

7070 7150 8420 8490

Baltimore Aircoil

FXV - C 15

FXV 64x - FXV 66x

(mm)

Air Flow (m3/s)

Fan Motor (kW)

Spray Water Flow (l/s)

Pump Motor (kW)

Coil Volume (L)

Inlet/Outlet Coil Conn. (mm)

3690 3690 3690 3690 3690 3690 3690 3690

3610 3610 3610 3610 3610 3610 3610 3610

39,9 44,3 47,0 43,7 46,4 49,6 45,8 49,0

(2x) 5,5 (2x) 7,5 (2x) 9,0 (2x) 7,5 (2x) 9,0 (2x) 11 (2x) 9,0 (2x) 11

45,1 45,1 45,1 45,1 45,1 45,1 45,1 45,1

4 4 4 4 4 4 4 4

(1x) 723 (1x) 723 (1x) 723 (1x) 896 (1x) 896 (1x) 896 (1x) 1069 (1x) 1069

(1x) ND 100 (1x) ND 100 (1x) ND 100 (1x) ND 100 (1x) ND 100 (1x) ND 100 (1x) ND 100 (1x) ND 100

4930 4930 4930 4930 4930 4930

5520 5520 5520 5520 5520 5520

3610 3610 3610 3610 3610 3610

68,6 72,8 77,9 67,3 62,5 76,5

(3x) 7,5 (3x) 9,0 (3x) 11 (3x) 7,5 (3x) 9,0 (3x) 11

56,8 56,8 56,8 56,8 56,8 56,8

5,5 5,5 5,5 5,5 5,5 5,5

(1x) 821 (1x) 821 (1x) 821 (1x) 1084 (1x) 1084 (1x) 1084

(1x) ND 100 (1x) ND 100 (1x) ND 100 (1x) ND 100 (1x) ND 100 (1x) ND 100

4930 4930 4930

5520 5520 5520

3610 3610 3610

65,4 69,5 74,4

(3x) 7,5 (3x) 9,0 (3x) 11

56,8 56,8 56,8

5,5 5,5 5,5

(1x) 1658 (1x) 1658 (1x) 1658

(1x) ND 150 (1x) ND 150 (1x) ND 150

Model No. FXV

Operating Weight (kg)

Shipping Weight (kg)

Heaviest Section (kg)

H

L

W

(mm)

(mm)

FXV 642-L FXV 642-M FXV 642-N FXV 643-M FXV 643-N FXV 643-O FXV 644-N FXV 644-O

9070 9090 9110 9770 9800 9810 10470 10480

5380 5400 5420 5880 5900 5910 6370 6380

3490 3510 3530 3990 4010 4020 4480 4490

4790 4790 4790 4790 4790 4790 4790 4790

FXV 661-M FXV 661-N FXV 661-O FXV 662-M FXV 662-N FXV 662-O

12260 12300 12320 13270 13310 13330

7000 7050 7060 7710 7760 7770

4360 4400 4420 5070 5110 5130

FXV Q661-M FXV Q661-N FXV Q661-O

15310 15360 15370

9160 9210 9220

6510 6560 6570

General Notes FXV 1. Operating weight is for the tower with the water level in the cold water basin at the overflow. 2. When the flow rate for FXV units exceeds 25 l/s the quantity of the coil connections will be double. When the flow rate for FXV-Q units exceeds 57 l/s, connections of ND200 will be used (1 x inlet; 1 x outlet). 3. Inlet and outlet connections are beveled for welding.

4. Standard make-up, drain and overflow connections are MPT. 5. Dimensional drawings show standard (right hand) arrangements. Left hand arrangements can be furnished by special order. 6. All FXV-models will be shipped in two sections: upper and lower section. 7. FXV-units have standard Low Noise Fans. For units with optional Whisper Quiet Fans, a “W” is added at the end of the model name.

... because temperature matters

Closed Circuit Cooling Towers

1. Fluid in; 2. Fluid out ND 3. Make-Up ND25; 4. Overflow ND80; 5. Drain ND50; 6. Access door; 7. Vent ND15.

FXV - C 16

FXV

Sound Attenuation FXV Models

1. Intake Attenuator; 2. Discharge Attenuator.

Dimensions (mm)

Weight (kg)

Model No FXV

D

Ht

Intake

Discharge

FXV 42x

1345

4715

100

140

FXV 43x

1345

4715

130

210

FXV (Q)44x

1345

4715

175

255

FXV (Q)54x

1500

5525

250

270

FXV (Q)56x

1500

5665

375

385

FXV 64x

2005

5525

250

310

FXV (Q)66x

2005

5665

375

440

W = Unit Width, see general Engineering data.

Remote Sump Data FXV Models Refer to the "Technical Resources" section "Selection of Remote Sump" for Remote Sump Data.

Baltimore Aircoil

FXV - C 17

Heat Loss Data FXV

Min Flow (l/s)

FXV 422 FXV 423

Positive Closure Damper Hood Total Height (Ht) (mm)

Standard Unit

Unit with Positive Closure Damper Hood

Weight (kg)

Length (L) (mm)

Width (X) (mm)

Height (Y) (mm)

3

25,6 30,9

13,2 14,1

150 150

1815 1815

1045 1045

835 835

4715 4715

FXV 432 FXV 433

3

38,5 46,4

18,4 19,7

200 200

2730 2730

1045 1045

835 835

4715 4715

FXV 442 FXV 443 FXV 444

5

50,7 61,0 70,7

23,0 24,5 26,0

250 250 250

3645 3645 3645

1045 1045 1045

835 835 835

4715 4715 4715

FXV Q440 FXV Q441

10

50,7 70,7

23,0 26,0

250 250

3645 3645

1045 1045

835 835

4715 4715

FXV 542 FXV 543 FXV 544

6

71,1 86,0 99,9

29,7 31,4 33,0

310 310 310

3645 3645 3645

1490 1490 1490

835 835 835

5525 5525 5525

FXV Q540 FXV Q541

12

71,1 99,9

29,7 33,0

310 310

3645 3645

1490 1490

835 835

5525 5525

FXV 561 FXV 562

6

82,9 105,8

42,8 44,8

450 450

5480 5480

1490 1490

835 835

5665 5665

FXV Q560 FXV Q561

12

105,8 147,6

44,8 48,6

450 450

5480 5480

1490 1490

835 835

5665 5665

FXV 642 FXV 643 FXV 644

7

76,2 91,8 106,4

30,7 32,3 33,9

340 340 340

3645 3645 3645

1615 1615 1615

835 835 835

5525 5525 5525

FXV 661 FXV 662

7

89,3 113,6

44,2 46,2

490 490

5480 5480

1615 1615

835 835

5665 5665

FXV Q661

14

157,4

50,1

490

5480

1615

835

5665

Notes: 1. Heat loss data based on 10°C coil water and –14°C ambient temperature with 20 m/s wind velocity (fans and pump off). 2. Positive closure dampers are available to reduce the heat loss during shut down. Consult your BAC Balticare representative for further details.

3. Electric immersion heaters with thermostat and low level cut out switch. All components are factory installed in the cooler pan. Heaters are selected to maintain +4°C pan water at –18°C ambient temperature. In outdoor locations trace heating and insulation of spray pump(s) (by others) may be required for freeze protection. 4. Hood weight excludes shipping skid weight.

... because temperature matters

Closed Circuit Cooling Towers

Heat Loss Data (kW) Model No. FXV

FXV - C 18

Structural Support FXV Models REMARK: Do not use for construction. Refer to factory certified dimensions & weights. This brochure includes data current at time of publication, which should be reconfirmed at the time of purchase. In the interest of product improvement, specifications, weights and dimensions are subject to change without notice. Up-to-date engineering data and more can be found at www.BaltimoreAircoil.com.

FXV

The recommended support arrangement for units consists of parallel I-beams running the full length of the unit, spaced as shown in the following drawing. Besides providing adequate support, the steel also serves to raise the unit above any solid foundation to ensure access to the bottom of the unit. To support units in an alternate steel support arrangement, consult your BAC Balticare Representative.

Units with and without Sound Attenuation

1. Unit Outline, 2. Air Intake, 3. Mounting Holes, 4. Unit

Model FXV FXV 42x

Dimensions (mm)

Max. Deflection (mm)

No of 20 mm Anchorbolts

W

L

A

B

C

5

2385

1861

2325

-

255

4

FXV 43x

8

2385

2775

2325

-

255

4

FXV (Q)44x

10

2385

3690

2325

-

255

4

FXV (Q)54x

10

2985

3690

2925

-

255

4

FXV 64x

10

3610

3690

3550

-

255

4

FXV (Q)56x

12

2985

5520

2925

2440

270

8

FXV (Q)66x

12

3610

5520

3550

2440

270

8

Notes : 1. Support steel and anchor bolts to be designed and furnished by others. 2. All support steel must be level at the top. 3. Beams must be selected in accordance with accepted structural practice. Maximum deflection of beam under unit see table. 4. If vibration isolation rails are to be used between the unit and supporting steel, be certain to allow for the length of the vibration

rails when determining the length of the supporting steel, as vibration rail length and mounting hole locations may differ from those of the unit. 5. If point vibration isolation is used with multi-cell units, the isolators must be located under the support steel, not between the support steel and the towers. 6. All mounting holes have a diameter of 22mm.

Baltimore Aircoil

FXV - C 19

Engineering Data FXV-D Models REMARK: Do not use for construction. Refer to factory certified dimensions & weights. This brochure includes data current at time of publication, which should be reconfirmed at the time of purchase. In the interest of product improvement, specifications, weights and dimensions are subject to change without notice. Up-to-date engineering data and more can be found at www.BaltimoreAircoil.com.

FXV-D Double Sided Units

* Actual shipping dimensions.

Model No. FXV-D

Max. Operating Weight (kg)

Max. Shipping Weight (kg)

Max. Heaviest Section (6) (kg)

H (mm)

L (mm)

W (mm)

A (mm)

Max. Air Flow (m3/s)

Fan Motor (kW)

Spray Water Flow (l/s)

Pump Motor (kW)

Coil Volume (l)

FXV-D288-3-xy FXV-D288-4-xy FXV-D288-1Q-xy

20745 22420 22420

13280 14540 14540

3650 4280 4280

5665 5665 5665

3632 3632 3632

7328 7328 7328

3498 3498 3498

100,7 99,5 99,4

15 to 45 15 to 45 15 to 45

113,6 113,6 113,6

(2x) 5,5 (2x) 5,5 (2x) 5,5

(2x) 1082 (2x) 1294 (2x) 1283

FXV-D364-3-xy FXV-D364-4-xy FXV-D364-1Q-xy

24290 26265 26265

15175 16660 16660

4260 5005 5005

5665 5665 5665

4245 4245 4245

8014 8014 8014

4184 4184 4184

126,4 124,7 124,6

18,5 to 55 18,5 to 55 18,5 to 55

113,6 113,6 113,6

(2x) 5,5 (2x) 5,5 (2x) 5,5

(2x) 1268 (2x) 1514 (2x) 1540

General Notes FXV-D 1. Operating weight is for the tower with the water level in the cold water basin at the overflow. 2. The actual size and number of inlet and outlet connections may vary with the design flow rate. Consult unit print for dimensions. 3. Inlet and outlet connections are beveled for welding. 4. Standard make-up, drain and overflow connections are located on the bottom of the unit.

5. Models shipped with an optional gear drive may have heights up to 130 mm greater than shown. Models with fan motor up to 22 kW are belt driven only; models with motor between 22 kW and 45 kW have standard belt drive but gear drive as an option; models with 55 kW motor have gear drive only. Motor size for a specific model is indicated by a letter “x” at the end of the model name. Fan type is indicated by an additional letter “y” at the end of the model name. “L” refers to the standard Low Noise Fan; “W” refers to the Whisper Quiet fan. 6. FXV-D Models will be shipped in four sections; 1 x lower, 1 x fan and 2 x coil section. Weight is shown for one coil section.

... because temperature matters

Closed Circuit Cooling Towers

1. Fluid out (see Note 2); 2. Fluid in (see Note 2); 3. Make-up ND40; 4. Overflow ND80; 5. Drain ND50; 6. Access Door

FXV - C 20

FXV

Sound Attenuation FXV-D Models

1. Inlet Attenuator; 2. Discharge Attenuator (not for FXV-DW available).

Model No FXV-D

Dimensions (mm) D

Weight (kg) Ht

Both Intake Sides

Discharge

FXV-D288

3510

6477

700

500

FXV-D364

4170

6477

850

600

Baltimore Aircoil

FXV - C 21

Heat Loss Data FXV-D

Positive Closure Damper Hood Total Height (Ht) (mm)

Standard Unit

Unit with Positive Closure Damper Hood

Total Weight (kg)

Length (L) (mm)

Width (X) (mm)

Height (Y) (mm)

18 18 36

222,8 258,2 258,2

81,1 86,3 86,3

470

3632

1915

740

6230

18 18 36

262,0 303,7 303,7

96,8 101,5 101,5

545

4245

1915

740

6230

Model No. FXV

Min. Flow (l/s)

FXV-D288-3 FXV-D288-4 FXV-D288-1Q FXV-D364-3 FXV-D364-4 FXV-D364-1Q

Notes: 1. Heat loss data based on 10°C coil water and –14°C ambient temperature with 20 m/s wind velocity (fans and pump off). 2. Positive closure dampers are available to reduce the heat loss during shut down. Consult your BAC Balticare representative for further details. 3. Electric immersion heaters with thermostat and low level cut out switch. All components are factory installed in the cooler pan.

Heaters are selected to maintain +4°C pan water at –18°C ambient temperature. In outdoor locations trace heating and insulation of spray pump(s) (by others) may be required for freeze protection. 4. Hood weight excludes shipping skid weight. 5. Models shipped with optional gear drive may be higher.

Remote Sump Data FXV-D Models Refer to the "Technical Resources" section "Selection of Remote Sump" for Remote Sump Data.

... because temperature matters

Closed Circuit Cooling Towers

Heat Loss Data (kW)

FXV - C 22

Structural Support FXV-D Models REMARK: Do not use for construction. Refer to factory certified dimensions & weights. This brochure includes data

FXV

current at time of publication, which should be reconfirmed at the time of purchase. In the interest of product improvement, specifications, weights and dimensions are subject to change without notice. Up-to-date engineering data and more can be found at www.BaltimoreAircoil.com. The recommended support arrangement for units consists of parallel I-beams running the full length of the unit, spaced as shown in the following drawing. Besides providing adequate support, the steel also serves to raise the unit above any solid foundation to ensure access to the bottom of the unit. To support units in an alternate steel support arrangement, consult your BAC Balticare Representative.

Units with and without Sound Attenuation

1. Unit Outline; 2. Air Intake; 3 Mounting Holes

Model FXV-D

Max. Deflection (mm)

Dimensions (mm) A

B

C

No of 20 mm Anchorbolts

FXV-D 288

12

3558

3570

37

12

FXV-D 364

12

4171

3913

37

12

Notes: 1. The recommended support arrangement for the units consists of parallel I-beams extending the full length of the unit. Supports and anchor bolts are to be designed and furnished by others. 2. All supporting beams are to be flush and level at top and must be oriented relative to gage line as shown. 3. Recommended design loads for each unit support beam should be 70% of the total unit operating weight applied as a uniform load to each of the unit beams. Beams should be designed in accordance with standard structural practice. For the maximum allowable deflection of beams under the unit see table.

4. All mounting holes have a diameter of 22 mm at the locations shown. 5. If vibration isolators are used, a rail or channel must be provided between the unit (and optional attenuator) and the isolators to provide continuous unit support. Additionally the support beams must be designed to accommodate the overall length and mounting hole location of the isolators that may differ from those of the unit. Refer to vibration isolator drawings for these data.

Baltimore Aircoil

FXV - C 23

Engineering Specifications 1.0 Closed Circuit Cooling Tower

(Alternate 1.1) General: Furnish and install ____factory assembled closed circuit cooling tower(s) of induced draft design with dual side air entry and vertical air discharge. Overall dimensions shall not exceed approximately ____ mm long x ____ mm wide, with an overall height not exceeding approximately _____ mm. Operating weight shall not exceed ____ kg. The closed circuit cooling tower(s) shall be Baltimore Aircoil Company Model(s)________________. 1.2. Thermal Capacity (water as heat transfer fluid): The closedcircuit cooling tower(s) shall be warranted by the manufacturer to cool ______l/s of _______ water from ____°C to ____°C at ____°C entering wet-bulb temperature. Coil pressure drop shall not exceed ________ kPa. (Alternate1.2.) Thermal Capacity (aqueous glycol solution as heat transfer fluid): The closed circuit cooling tower(s) shall be warranted by the manufacturer to cool ________l/s of _____% by volume ethylene/propylene glycol solution from ______°C to _____°C at

_____°C entering wet-bulb temperature. Coil pressure drop shall not exceed ________ kPa. 1.3. Corrosion Resistant Construction: Unless otherwise noted in this specification, all steel panels and structural members shall be constructed of heavy-gauge Z600 metric hot-dip galvanized steel, with all sheared edges given a protective coating of zinc-rich compound and the exterior protected with the Baltiplus Corrosion Protection. (Alternate1.3.) Corrosion Resistant Construction: Unless otherwise noted in this specification, all steel panels and structural members shall be protected with the BALTIBOND® Corrosion Protection System. The system shall consist of Z600 metric hot-dip galvanized steel prepared in a four-step (clean, pre-treat, rinse, and dry) process with an electrostatically sprayed, thermosetting hybrid polymer fuse-bonded to the substrate during a thermally activated curing stage and monitored by a 23-step quality assurance program. 1.4. Quality Assurance: The closed circuit cooling tower manufacturer shall have a management system certified by an accredited registrar as complying with the requirements of ISO9001:2000 to ensure consistent quality of its products and services. 1.5. Warranty: The manufacturer’s standard equipment warranty shall be for a period of not less than one year from date of startup or eighteen months from date of shipment, whichever occurs first.

2.0 Construction Details 2.1 Coil Section: The heat transfer section of the closed circuit cooling tower shall be encased with removable heavy-gauge galvanized steel panels (or corrosion resistant, fiberglass reinforced polyester (FRP) on Models FXV-D). The coil shall be constructed of continuous serpentine all prime surface steel designed for 10 bar, and be hot-dip galvanized after fabrication. The coil shall be designed for free drainage of fluid. 2.2 Cold Water Basin: The basin shall include a depressed section with drain/clean-out connection. Standard accessories shall include large area, lift-out steel strainers with perforated openings sized

smaller than water distribution nozzle orifices, and integral antivortexing hood to prevent air entrainment, waste water bleed line, and brass make-up valve with large diameter plastic float arranged for easy adjustment. 2.3 Casing Panels: For models FXV with single air inlet side the casing panels shall be constructed of steel matching the structure defined in section 1.3. For Models FXV-D the casing panels shall be constructed of corrosion resistant, fiberglass reinforced polyester (FRP).

3.0 Mechanical Equipment 3.1 Fan(s): Fan(s) shall be heavy-duty, axial flow low noise, with aluminium alloy blades. Air shall discharge through a fan cylinder designed for streamlined air entry and minimum fan blade tip clearance for maximum fan efficiency. (Alternate 3.1) Fan(s) for FXV-models: Fan(s) shall be of “Whisper Quiet” fan design for ultra low sound consisting of specially shaped aluminium blades with end caps and flexible hub connection. (Alternate 3.1) Fan(s) for FXV-D models: Fan(s) shall be of “Whisper Quiet” fan design for ultra low sound consisting of multiblade aerofoil fan design constructed of fibreglass reinforced plastic blades. 3.2 Fan(s) and shaft(s) shall be supported by heavy-duty, selfaligning, grease-packed ball bearings with moisture-proof seals and integral slinger rings, designed for minimum L10 life of 40,000 hours.

Fan(s) shall be belt driven and specifically designed for evaporative cooling service. Fan and motor sheave(s) shall be fabricated from cast aluminum. 3.3 Independent motor and drives: Each fan is equipped with an independent motor and drive assembly, which allows independent operation of each fan. 3.4 Fan Motor: Fan motor(s) shall be totally enclosed fan cooled (TEFC), reversible, squirrel cage, ball bearing, designed specifically for evaporative cooling duty on _____ volts___ hertz ___ phase electrical service. The motor shall be furnished with special moisture protection on windings, shafts, and bearings. Each motor shall be mounted on an easily adjusted, heavy-duty motor base.

4.0 Wet Deck Surface and Drift Eliminators 4.1. BACross® Wet Deck Surface and Drift Eliminators (FXV models): The wet deck surface and integral drift eliminators shall be formed from plastic material and shall be impervious to rot, decay, fungus and biological attack. The surface shall be manufactured and performance tested by the closed circuit cooling tower manufacturer to provide single source responsibility and assure control of the final product. A separate set of drift eliminators shall be removable in easily handled sections for quick access to the coil. Eliminators shall have a minimum of three changes in air direction.

(Alternate 4.1) BACross II Wet Deck Surface and Drift Eliminators (FXV-D models): The wet deck surface and integral drift eliminators shall be formed from plastic material and shall be impervious to rot, decay, fungus and biological attack. The surface shall be manufactured and performance tested by the closed circuit cooling tower manufacturer to provide single source responsibility and assure control of the final product. A separate set of drift eliminators shall be removable in easily handled sections for quick access to the coil. Eliminators shall have a minimum of three changes in air direction.

... because temperature matters

Closed Circuit Cooling Towers

1.1 General: Furnish and install ____factory assembled closed circuit cooling tower(s) of induced draft design with single side air entry and vertical air discharge. Overall dimensions shall not exceed approximately ____ mm long x ____ mm wide, with an overall height not exceeding approximately _____ mm. Operating weight shall not exceed ____ kg. The closed circuit cooling tower(s) shall be Baltimore Aircoil Company Model(s)________________.

FXV - C 24

5.0 Combined Inlet Shields 5.1. Combined Inlet Shields: Combined inlet shields shall be separate from the wet deck surface and removable to allow easy access for inspection of the air/water interface at the air inlet side of the equipment. Combined inlet shields shall prevent UV-light and

debris from entering the unit, as well as prevent water splash out during fan cycling. They shall be constructed of maintenance free, corrosion and UV resistant material.

FXV

6.0 Spray Water System 6.1 Spray Water Pump(s): The closed circuit cooling tower shall include an appropriate number of close-coupled, bronze-fitted centrifugal pump and motor assemblies equipped with mechanical seal, mounted in the basin and piped from the suction connection to the water distribution system. The pump motor(s) shall be the totally enclosed fan cooled (TEFC) type suitable for _____ volts, ___ phase, and ____ hertz electrical service. The system shall include a metering valve and bleed line to control the bleed rate from the pump discharge to the overflow connection.

6.2 Water Distribution System: Water shall be distributed evenly over the coil at a flow rate sufficient to ensure complete wetting of the coil at all times. Large diameter, non-clog, 360° plastic distribution nozzles shall utilize a two stage diffusion pattern to provide overlapping, umbrella spray patterns that create multiple intersection points with adjacent nozzles. The branches and spray nozzles shall be held in place by snap-in rubber grommets, allowing quick removal of individual nozzles or complete branches for cleaning or flushing.

7.0 Access 7.1 Plenum Access: A large, hinged access door shall be provided for access to the coil, drift eliminators and fan plenum section. The

water make-up valve, float ball and suction strainer shall be easily accessible.

8.0 Sound 8.1 Sound Level: To maintain the quality of the local environment, the maximum sound pressure levels (dB) measured 15 m from the

Location

63

125

250

cooling tower operating at full fan speed shall not exceed the sound levels detailed below.

500

Discharge Air Inlet End Back (not on D-models)

Baltimore Aircoil

1000

2000

4000

8000

dB(A)

HWD - D 1

Water Saving Hybrid Wet-Dry Products Overview

Water Saving Products

Product Group Detail General Information ................................................................................. D2 Principle of Operation .............................................................................. D2 Configuration ............................................................................................. D2 Fan System ................................................................................................. D3 Capacity Range .......................................................................................... D4 Maximum Entering Fluid Temperature .................................................. D4 Typical Applications .................................................................................. D4 Product Line Overview Table .................................................................. D4 Advantages of Intelligent Water Saving Products ................................. D6 Engineering Considerations ..................................................................... D6

HWD - D 2

General Information

Overview

Water saving and hybrid products provide cooling for many types of systems, and the specific application will largely determine which BAC product is best suited for a project. Water saving and hybrid products can be categorised within three different technologies. These are the hybrid wetdry, dry and adiabatic and the Product Line Overview Table indicates the BAC products available under each of these technologies. This overview table is intended as a general guide. Specialised assistance is available through your local BAC Balticare Representative. Refer to the section “Advantages of water saving and hybrid wet-dry products” for the advantages of each technology.

Principle of Operation Water saving and hybrid products are usually of the closed circuit type where the heat load to be rejected is transferred from the process fluid (Fluid to be cooled) to the ambient air through a heat exchange coil. The coil serves to isolate the process fluid from the outside air, keeping it clean and contamination free in a closed loop. The Hybrid wet-dry products cool the liquid to be cooled by efficiently combining dry sensible air cooling with evaporative cooling. These products include two or more distinctive heat transfer surfaces or sections combined into one product optimising the use of the ambient dry and wet bulb temperature. Dry Fluid Coolers cool the liquid in a closed circuit by means of sensible heat transfer from the highdensity finned coil block to the air at ambient dry bulb temperature. TrilliumSeries Coolers are dry coolers equipped with an Adiabatic Pre-Cooler section. Before the air is drawn through the high density finned coil, it is pre-cooled adiabatically as it passes through an evaporative pad where water is evaporated in the air.

Configuration BAC manufactures two types of water saving and hybrid wet-dry products: combined flow and counterflow.

Combined Flow Combined flow is the use of a prime surface and a dry finned heat exchange coil in combination with a wet deck surface for heat transfer in a hybrid wet-dry product. The addition of wet deck surface hybrid wet-dry product reduces evaporation in the coil section and is also used as an adiabatic pre-cooler section. BAC’s combined hybrid wet-dry products utilize parallel flow of air and spray water over the prime surface coil, counterflow of fluid and air in the dry finned coil and crossflow air/water flow through the wet deck surface. In parallel flow, air and water flow over the coil in the same direction. The process fluid travels from the bottom to the top of the coil, increasing efficiency by bringing the coldest spray water and air in contact with the process fluid at its coldest temperature.

Combined Flow: Parallel flow of air and water over the coil in counterflow with the fluid inside the coil

Baltimore Aircoil

Combined flow: Crossflow configuration over the wet deck

HWD - D 3

Counterflow Configuration

Counterflow In a counterflow water saving and hybrid wet-dry product, the flow of the air is in the opposite direction of the spray water or fluid inside the heat exchange coil. In BAC’s counterflow dry and adiabatic products, air travels vertically up through the coil while the fluid in the coil travels down.

Fan System The flow of air through most factory assembled water saving hybrid wet-dry products is provided by one or more mechanically driven fans. The fan(s) may be axial or centrifugal, each type having its own distinct advantages. Centrifugal fan units are capable of overcoming reasonable amounts of external static pressure (≤ 125 Pa), making them suitable for both indoor and outdoor installations. Centrifugal fans are also inherently quieter than axial fans, although the difference can be overcome through the application of optional fan speed control, low sound fans and/or sound attenuation on axial fan units. Fans can be applied in an induced draft or a forced draft configuration.

Centrifugal Fans

Axial Fans

Induced Draft The rotating air handling components of induced draft equipment are mounted in the top deck of the unit, minimising the impact of fan noise on near-by neighbours. The air being drawn through the unit hereby discharges over the inducing fan. The use of corrosion resistant materials ensures long life and minimises maintenance requirements for the air handling components. Forced Draft Rotating air-handling components are located on the air inlet face at the base of forced draft towers whereby fresh air is blown through the unit. This base fan position facilitates easy access for routine maintenance and service. Additionally, location of these components in the dry entering air stream extends component life by isolating them from the corrosive saturated discharge air when units operate in evaporative mode.

... because temperature matters

Water Saving Products

Combined flow: Counterflow of air over the coil and fluid inside the coil

HWD - D 4

Capacity Range In the Product Line Overview Table, product capacities are called out in terms of a fluid flow rate for hybrid wet-dry products and nominal kW of heat rejection capacity for dry and TrilliumSeries products. All capacities shown are for a single cell; multiple cell units can be applied to achieve larger capacities.

Overview

Maximum Entering Fluid Temperature All BAC hybrid wet-dry products are capable of withstanding entering fluid temperatures as high as 82ºC. All BAC dry products are capable to withstanding entering fluid temperatures as high as 65°C and all BAC TrilliumSeries Products as high as 60°C.

Typical Applications A list of typical applications is provided in the Product Line Overview Table for your reference.

Product Line Overview Table HXI

HFL

2

2

12

12

3

3

1 9 13

11

Principle of Operation

9

4

2

11 4

7 2

6

5 8

1 10

5

1

13 8

10

Technology

Hybrid Wet-Dry closed circuit cooling tower combining sensible and evaporative heat transfer

Hybrid Wet-Dry closed circuit cooling tower combining sensible and evaporative heat transfer.

Configuration

Combined Flow

Counterflow

Fan System

Axial Fan, Induced Draft

Centrifugal Fan, Forced Draft

Capacity Range (Single Cell)

3 to 50 l/s

9 to 90 l/s

Maximum Entering Fluid Temperature

82°C

82°C

Typical Applications

Medium to large HVAC & industrial applications Installations requiring plume abatement Installation requiring water conservation Low energy consumption Easy maintenance

Medium to large HVAC & industrial applications Installations requiring plume abatement Installation requiring water conservation Sound sensitive locations Indoor Installations

1. Air in; 2. Air out; 3. Fluid in; 4. Fluid out; 5. Water, 6.Combined Inlet Shields; 7. Wet deck surface; 8. Cold water basin; 9. Water distribution system; 10. Spray water pump; 11. Coil; 12. Finned coil; 13. Three way valve.

Baltimore Aircoil

HWD - D 5

DFCV-AD – TrilliumSeries Coolers

3

9

2

4

10

6

4 1

5

9

3

9

6

1

5

8

8

10

1 3 10

10

7

2

7

Dry Fluid Coolers cool the liquid in a closed circuit by means of sensible heat transfer using a high-density finned coil block.

TrilliumSeries Coolers equipped with an Adiabatic Pre-Cooler cool the liquid by sensible heat transfer only. Before the air is drawn through the high density finned coil however, it is pre-cooled adiabatically as it passes through an evaporative pad where water is evaporated in the air.

Counterflow

Counterflow

Axial Fan, Induced Draft

Axial Fan, Induced Draft

30 kW – 1110 kW at Eurovent Conditions according to EN 1048. 1,5 – 80 l/s 34% Ethylene Glycol Solution at 40 oC / 35 oC / 25 oC dry bulb temperature

220 kW – 1620 kW at Eurovent Conditions according to EN 1048. 12 – 86 l/s 34% Ethylene Glycol Solution at 40 oC / 35 oC / 25 oC dry bulb temperature

65 oC High temperature execution available on DFC, max. 150 oC, max. 10 bar pressure

60 oC

Small to medium HVAC and industrial applications Locations with limited water availability Large range, large approach applications High temperature industrial applications

Small to medium HVAC and industrial applications Locations with limited water and limited space availability

1. Dry heat exchanger coil; 2. Fluid Inlet. 3. Fluid Outlet; 4. Axial Fans; 5. High efficient evaporative cooling pad; 6. Water inlet connections; 7. Water outlet connections; 8. Adiabatic cooling of ambient air; 9. Air discharge; 10. Air in.

REMARK: For the principle of operation for HXC (Hybrid Condenser) and DCV-AD (TrilliumSeries Condenser) refer to the “Evaporative Condenser Overview”.

... because temperature matters

Water Saving Products

DFCH / DFCT or DFCV – Dry Coolers (only DFCH principle of operation is shown)

HWD - D 6

Advantages of Intelligent Water Saving Products Low water and water treatment cost, vastly improved operational safety and virtual elimination of visible plume are the main advantages of “intelligent” water saving products from Baltimore Aircoil. With a choice between different configurations and a vast array of material options and accessories water saving technology from Baltimore Aircoil can be optimally incorporated in any application.

Overview

Low Water Consumption reduces operating cost In many European countries water has become an expensive commodity and hence the cost of water often represents a significant portion of the total annual operating cost of conventional evaporative cooling equipment. To significantly reduce operating cost, BAC can offer a variety of “intelligent” water saving solutions. These solutions include air-cooled products with no water consumption at all, TrillumSeries coolers and wet-dry hybrid coolers, which consume only water when needed and as much as needed. The broad array of water saving products allows to optimise a choice for each application, including the ones where low cooling temperatures need to be achieved during a hot summer day. The cost premium associated with water saving products is usually offset in short time by the operating cost savings that can be achieved.

Lower Water Treatment Cost The cost for water treatment in cooling applications is generally related to the amount of water consumed during a year. Water saving “intelligence” therefore also saves water treatment cost. For hybrid and TrilliumSeries products periods of dry operation exist, where no water treatment at all is needed and the water treatment system does not need to be inspected, since there is no water in the products. In particular for TrilliumSeries coolers, extensive periods of dry operation can be expected. During such periods no biological contamination of the environment can happen.

Reduction/Elimination of Visible Plume In certain applications visible plume is considered as hinder. The use of "intelligent" water saving products from BAC will either greatly reduce the formation of visible plume or completely eliminate it. Especially when during the winter period dry operation of the products can be applied, the occurrence of visual plume will virtually be eliminated.

Engineering Considerations Location Units must have an adequate supply of fresh air to the air inlet(s). When units are located adjacent to building walls or in enclosures, care must be taken to ensure that the warm, saturated discharge air is not deflected off surrounding walls or enclosures and drawn back to the air inlet(s). Warning: Each unit should be located and positioned to prevent the introduction of the warm discharge air and the associated drift (hybrid wet-dry products), which may contain chemical or biological contaminants including Legionella, into the ventilation systems of the building on which the unit is located or those of adjacent buildings.

Note: For detailed recommendations on layout, please consult your local BAC Balticare Representative.

For HFL products, bottom screens or solid bottom panels may be desirable or necessary for safety, depending on the location and conditions at the installation site.

Baltimore Aircoil

HWD - D 7

Piping and Valves Piping must be sized and installed in accordance with good piping practice. All piping should be supported by pipe hangers or other supports, not by the unit. Some installations may require flow balancing valves (supplied by others) at the coil inlets to balance the flow to individual coils and cells. External shutoff valves on the closed circuit loop (supplied by others) may also be required if the system design necessitates the isolation of individual cells.

Capacity Control Variable Frequency Drives (VFD) Installations which are to be controlled by Variable Frequency Drives (VFD) require the use of an inverter duty motor as designed IEC 34.1, which recognizes the increased stresses placed on motors by these drive systems. Inverter duty motors must be furnished on VFD applications in order to maintain the motor warranty. Fan motors must be furnished with thermal protection (either PTC sensors or coil thermostats normally open, or normally closed). The motor protection consists of temperature sensitive cutout devices embedded in the motor windings (minimum 3 per motor). The minimum fan motor speed during normal operation should not be below 30% of the speed indicated on the motor nameplate. This corresponds with 15 Hz for a 50 Hz supply and 18 Hz for a 60 Hz supply. Warning: When the fan speed is to be changed from the factory-set speed, including through the use of a variable speed control device, steps must be taken to avoid operating at or near fan speeds that cause a resonance with the unit or its supporting structure. At start-up, the variable frequency drive should be cycled slowly between zero and full speed and any speeds that cause a noticeable resonance in the unit should be “locked out” by the variable speed drive.

Fan Cycling Fan cycling is the simplest method of capacity control. The number of steps of capacity control can be increased using the Baltiguard® Fan System, the independent fan motor option, or two-speed fan motors in conjunction with fan cycling (see the “Custom Features & Options” section of the appropriate product line to determine whether the Baltiguard® Fan System or the independent fan motor option are available; two-speed motors are available for all products). These options provide substantial energy savings when compared to simple fan cycling. Warning: Rapid on-off cycling can cause the fan motor to overheat. It is recommended that controls be set to allow a maximum of 6 on-off cycles per hour. Note: Spray water pump cycling should not be used for capacity control. This method of control often results in short cycling of the pump motor as capacity changes substantially with pump cycling. In addition, alternate wetting and drying of the coil promotes scaling of the heat exchanger coil surface.

Capacity Control Dampers (HFL models only) On centrifugal fan models, modulating capacity control dampers are available to provide close control of the leaving temperature. See Section "Accessories" or contact your local BAC Balticare representative.

... because temperature matters

Water Saving Products

Although equalizing lines can be used to balance water levels between multi-cell hybrid wet-dry products, the spray water for each cell must be treated separately, and a separate make-up must be provided for each cell. Note that a common remote sump for multi-cell installations can simplify make-up and water treatment – see "Technical Resources, Remote Sump Tank Selection" for details. See the appropriate Operating and Maintenance Instruction Manual for more information on water treatment.

HWD - D 8

Vibration Cut-out Switch Vibration cut-out switches are recommended on all axial fan installations. Vibration cut-out switches are designed to interrupt power to the fan motor and/or provide an alarm to the operator in the event of excessive vibration. BAC offers both electronic and mechanical vibration cut-out switches on all water saving and hybrid products.

Overview

Water Treatment (HFL, HXI and HXC models only) As water evaporates in the unit, the dissolved solids originally present in the water remain in the system. The concentration of these dissolved solids increases rapidly and can cause scale and corrosion. In addition, airborne impurities and biological contaminants, including Legionella, may be introduced into the circulating water. To control all potential contaminants, a water treatment program must be employed. In many cases, a simple bleed-off may be adequate for control of scale and corrosion. However, biological contamination, including Legionella, can be controlled only through the use of biocides. Such treatment should be initiated at system startup, after periods of equipment shutdown, and continued regularly thereafter. Accordingly, it is strongly recommended a biocide treatment be initiated when the unit is first filled with water and continued regularly thereafter. For more information, consult the appropriate Operating and Maintenance Manual. When a water treatment program is employed, it must be compatible with construction materials. Batch feeding of chemicals into the unit is not recommended. If units are constructed with optional corrosion resistant materials, acid treatment may be considered; however, the water quality must be maintained within the guidelines set forth in the Operating and Maintenance Instructions. Note: Unless a common remote sump is utilised, each cell of a multi-cell installation must be treated as a separate entity, even if the cold water basins are equalized.

For complete Water Quality Guidelines, see the appropriate Operating and Maintenance Instruction Manual, available at www.baltimoreaircoil.com. For specific recommendations on water treatment, contact a competent water treatment supplier.

Wet Deck Surface Compatibility (HXI models only) The standard wet deck surface in a HXI Hybrid Closed Circuit Cooling Tower is constructed of a plastic material This wet deck surface is compatible with the water found in most evaporative cooling applications. For applications where the entering fluid temperature exceeds 82°C, contact your local BAC Balticare Representative to confirm that the standard wet deck is acceptable.

Sound Levels Sound rating data are available for all BAC models. When calculating the sound levels generated by a unit, the designer must take into account the effects of the geometry of the tower as well as the distance and direction from the unit to noise-sensitive areas. Whisper Quiet fans and intake and discharge sound attenuation can be supplied on certain models to provide reduced sound characteristics (see the “Custom Features and Options” section of the appropriate product line for details). The Baltiguard® Fan System, two-speed motors, or variable frequency drives can also be used to reduce sound during periods of non-peak thermal loads. For more information on sound and how it relates to evaporative cooling equipment, see Section "Technical Resources, Fundamentals of Sound". Dry and TrilliumSeries coolers for sound sensitive applications are offered with low speed motors. For detailed low sound selections, please consult your local BAC Balticare Representative.

Baltimore Aircoil

HWD - D 9

Winterization (HFL HXI and HXC models only)

Indoor Installation (HFL models only) Many indoor installations require the use of inlet and/or discharge ductwork. Units installed with inlet ductwork must be ordered with solid-bottom panels. Generally, intake ducts are used only on smaller units while the equipment room is used as a plenum for larger units. Discharge ductwork will normally be required to carry the saturated discharge air from the building. Both intake and discharge ductwork must have access doors to allow servicing of the fan assembly, drift eliminators, and water distribution system. All ductwork is supplied and installed by others and should be symmetrical and designed to provide even air distribution across the face of air intakes and discharge openings. Such ductwork may increase the external static pressure on the unit, requiring a larger fan motor to be installed. This external static pressure must be quantified (in Pa) to BAC to allow for suitable fan motor sizing. Warning: The discharge opening must be positioned to prevent the introduction of discharge air into the fresh air intakes serving the unit or the ventilation systems of adjacent buildings.

Note: Axial fan units are not suitable for indoor installations.

Safety Adequate precautions, appropriate for the installation and location of these products, should be taken to safeguard the public from possible injury and the equipment and the premises from damage. Operation, maintenance and repair of this equipment should be undertaken only by personnel qualified to do so. Proper care, procedures and tools must be used in handling, lifting, installing, operating, maintaining, and repairing this equipment to prevent personal injury and/or property damage.

Fluid Compatibility The fluid to be cooled must be compatible with the coil material. Fluids not compatible with coil materials can lead to corrosion and tube failure. Certain fluids may require occasional pressure cleaning or mechanical cleaning of the inside of coil tubes. In such cases the coil must be designed to provide this capability. Refer to the appropriate product line section for details of the available coil material.

Open / Closed System (HXI and HFL unit coils) The standard galvanised steel serpentine coils (prime surface) are carbon steel, hot-dip galvanised on the outside only, and are intended for application on closed, pressurised systems which are not open to the atmosphere. Stainless steel coils are available to cool corrosive fluids or water and ethylene/propylene glycol solutions in systems open to the atmosphere

... because temperature matters

Water Saving Products

When a unit is shut down in freezing weather, the basin water must be protected by draining to an indoor auxiliary remote sump tank or by providing supplementary heat to the cold water basin. Supplementary heat can be provided by electric immersion heaters or in some cases, hot water, steam coils, or steam injectors. All exposed water piping, make-up lines, and spray pumps (if applicable) that do not drain at shutdown should be traced with electric heater tape and insulated. When dry operation is planned for low ambient conditions, centrifugal fan units should be supplied with oversized fan motors to prevent motor overload when the spray water is not operating. For remote sump applications, the spray water pump must be selected for the required flow at a total head which includes the vertical lift, pipe friction (in supply and suction lines) plus the required pressure at the inlet header of the water distribution system (14 kPa). A valve should always be installed in the discharge line from the pump to permit adjusting flow to the unit requirement. Inlet water pressure should be measured by a pressure gauge installed in the water supply riser at the spray water inlet, and adjusted to the specified inlet pressure.

HWD - D 10

Protection Against Coil Freezing

Overview

At below freezing ambient conditions, the unit can experience heat loss even without the recirculating spray water pump and fans in operation. Without a heat load on the circulating fluid, coil freezing can occur even at full flow. Protective means are readily available to avoid potential freeze problems. Where the system will permit, the best protection against coil freeze-up is the use of an industrially inhibited anti-freeze solution. When this is not possible, the system must be designed to meet both of the following conditions: 1. Maintain minimum recommended flow through the coil at all times, as per the table below: 2. Maintain a heat load on the circulating fluid so that the temperature of the fluid leaving the coil will not be below 7ºC. If the process load is extremely light, or if the process is periodically shut off entirely, then an auxiliary heat load must be applied to the circulating fluid when below freezing ambient temperatures exist to prevent damage to the coil. Refer to the Heat Loss Data table (see the product section for applicable heat loss data) for the auxiliary heat load requirement. The amount of auxiliary heat necessary to prevent coil freezing can be further reduced by the use of a positive closure damper hood and insulation. Draining the coil is not recommended as a normal method of freeze protection. However, draining is acceptable as an emergency method of freeze protection. Frequent draining can promote corrosion inside the coil tubes. If the coil is not protected by an industrially inhibited anti-freeze solution, an automatic drain valve and air vent is recommended to drain the coil if flow stops or fluid temperature drops below 7ºC when the ambient temperature is below freezing. Note that cold water basin heaters will not provide freeze protection for the coil. The coil of dry and TrilliumSeries coolers can never drain completely. If a minimum heat load can not be guaranteed on the dry coil during the winter period, then the use of an anti-freeze solution is the only available protection against coil freezing.

Model

Minimum Flow (l/s)

HFL 36X - 48X

4,1

HFL 72X - 96X

7,9

HFL 108X - 144X

12

HFL 150X - 192X

15,8

HFL 180X - 240X

19,9

HFL 216X - 288X

24

HXI 42 X, 43X

3

HXI 44X

5

HXI 54X, 56X

6

HXI Q54X, Q56X

12

HXI 64X, 66X

7

HXI Q64X, Q66X

14

Warranties Please refer to the Limitation of Warranties applicable to and in effect at the time of the sale/ purchase of these products.

Baltimore Aircoil

HXI - D 1

HXI

Hybrid Closed Circuit Cooling Towers

Water Saving Products

Product Detail HXI Hybrid Closed Circuit Cooling Towers .......................................... D2 Benefits ....................................................................................................... D4 Construction Details .................................................................................. D6 Custom Features and Options .................................................................. D8 Accessories ............................................................................................... D11 Engineering Data ..................................................................................... D13 Structural Support .................................................................................. D21 Engineering Specifications ..................................................................... D22 HXI offers Economic Advantages .......................................................... D24

HXI - D 2

HXI Hybrid Closed Circuit Cooling Towers Capacity

HXI

Single Cell Capacity: 3 - 50 l/s

General Description HXI Closed Circuit Hybrid Cooling Towers deliver fully rated thermal performance over a wide range of flow and temperature requirements. Distinct advantages of the HXI include plume abatement, significant water savings over traditional water-cooled equipment. Standard design features satisfy today’s environmental concerns, minimize installation costs, maximize year-round operating reliability, and simplify maintenance requirements.

Key Features z

Plume abatement

z

Maximum water savings

z

Low energy consumption

z

Low installed cost

z

Easy maintenance

z

Reliable year-round operation

z

Long service life

Baltimore Aircoil

HXI - D 3

Water Saving Products

... because temperature matters

HXI - D 4

Benefits Plume Abatement

HXI

The HXI offers a combination of sensible, adiabatic, and evaporative heat transfer to significantly reduce any plume that may occur with conventional evaporative cooling equipment. During the coldest times of the year, when the potential for visible discharge is greatest, the HXI operates 100% dry, completely eliminating plume.

Maximum Water Savings Water savings are achieved throughout the year with each of three different operating modes of the HXI. In some areas, the water cost savings alone can pay for the equipment in as little as two years! z

z

z

At peak conditions in the “dry/wet” operating mode, a significant amount of heat is removed by sensible heat transfer, providing reduced water consumption versus conventional evaporative cooling. When the heat load and/or ambient temperatures drop, water consumption is further reduced in the “adiabatic” operating mode. Water consumption is totally eliminated in the “dry” operating mode.

Note: See section "Engineering Specifications" for details on operating modes.

High Temperature Cooling The finned dry coil tempers the incoming fluid, allowing higher inlet water temperatures than traditional closed circuit cooling towers.

Low Energy Consumption The HXI provides heat rejection at the lowest possible energy input and maintenance requirements via: z

High efficiency, low kW axial fans

z

Multiple fan motor system

z

Closed loop cooling, which minimizes process fouling

z

z

Patented combined flow technology, which reduces evaporation directly off the coil, minimizing the potential for scaling and fouling Parallel flow of air and spray water, which eliminates scale-promoting dry spots

Low Installed Cost Support — All models mount directly on parallel I-beams and ship complete with motors and drives, factory-installed and aligned. Modular Design — Units ship in three pieces to minimize the size and weight of the heaviest lift, allowing for the use of smaller, less costly cranes.

Baltimore Aircoil

HXI - D 5

Easy Maintenance z

z

z

Access — Hinged access doors on each end wall and a standard internal walkway provide easy access to the unit interior. Spacious Interior — Provides easy access to the cold water basin, drift eliminators, fan drive system and the prime surface coil. Access to spray Distribution – Parallel flow of air and spray water over the coil allows for inspection and access to the top of the coil during full operation.

Removable Drift Eliminators

Reliable Year-Round Operation z

z

Belt Drive System utilizes special corrosion-resistant materials of construction and state-ofthe-art technology to ensure ease of maintenance and reliable year-round performance. Combined Inlet Shields prevent biological growth from sunlight, act as a filter for air borne impurities and debris and eliminate water splash out.

Long Service Life z

Materials of Construction – Various materials are available to meet the corrosion resistance, unit operating life, and budgetary requirements of any project.

Note: For more information, please refer to the section “Technical Resources, Materials of Construction”.

... because temperature matters

Water Saving Products

Large Access Door

HXI - D 6

HXI

Construction Details

Baltimore Aircoil

HXI - D 7

1. Heavy-Duty Construction z

7. BACross® Wet Deck Surface with Integral Drift Eliminators (Not Shown)

Z600 hot-dip galvanized steel panels

2. Fan Drive System (Not Shown)

z

Plastic material

Premium quality belts

z

Impervious to rot, decay and biological attack

z

Corrosion resistant sheaves

z

Designed and manufactured by BAC

z

Heavy-duty bearings

8. Combined Inlet Shield Technology

z

Adapted fan motor for operation in saturated conditions.

3. Low kW Axial Fan(s) (Not Shown)

z

Corrosion Resistant

z

Easily removable

z

UV resistant plastic material

z

Quiet operation

z

High Efficiency

z

Sloped cold water basin for easy cleaning

z

Corrosion resistant aluminum

z

Suction strainer with anti-vortex hood

z

Adjustable water make-up assembly from air inlet side

z

Integral internal walkway as standard

9. Cold Water Basin

4. Water Distribution System z

Visible and accessible during operation

z

Overlapping spray patterns ensure proper water coverage

z

Large orifice, non-clog nozzles

10. Hinged Access Doors z

5. Prime Surface Coil (Not Shown)

Inward swinging door

11. Three Way Valve (Optional)

z

Continuous serpentine, steel tubing

z

With actuator

z

Hot-dip galvanized after fabrication (HDGAF)

z

With connection box

z

Sloped tubes for free drainage of fluid

z

Designed for maximum 10 bar operating pressure according to PED

6. Dry Finned Coil z

Copper tubing with high density aluminum fins

z

Designed for max. 10 bar operating pressure according to PED

z

Staggered tubes coil arrangement

12. Recirculating Spray Pump (Not Shown) z

Close coupled, bronze fitted centrifugal pump

z

Totally enclosed fan cooled (TEFC) motor

z

Bleed line with metering valve installed from pump discharge to overflow

13. Manifolds and Interconnecting Pipework (Optional) z

With orifice plate

z

With hydraulic by-pass

... because temperature matters

Water Saving Products

z

HXI - D 8

Custom Features and Options Construction Options

HXI

z

z

Standard Construction: Steel panels and structural elements are constructed of Z600 heavy-gauge hot-dip galvanized steel protected with the Baltiplus Corrosion Protection on the outside of the cooling towers. Optional BALTIBOND® Corrosion Protection System: The BALTIBOND® Corrosion Protection System, a hybrid polymer coating used to extend equipment life, is applied to all hot-dip galvanized steel components of the closed circuit hybrid cooling tower (excluding heat transfer coils).

Note: See section Technical Resources, Material Options for more details on the materials described above.

Prime Surface Coil Configurations Standard Serpentine Coil: The standard cooling coil is constructed of continuous lengths of all prime surface steel, hot-dip galvanized (outside surface) after fabrication (HDGAF). The coil is designed for low pressure drop with sloping tubes for free drainage of fluid. Each coil is pneumatically tested at 15 bar and PED compliant.

Dry Finned Coil Configurations The standard finned coil on the HXI unit has 6 rows and is available in 1-1/2 serpentine and triple serpentine arrangements. The serpentine arrangement indicates the way in which these rows are circuited internally, and influences the process fluid velocity (the smaller the serpentine, the higher the flow velocity) and the total fluid pressure through the unit (the smaller the serpentine, the higher the finned coil pressure drop). Hence, the unit flow and pressure drop allowance must be taken into account when the finned coil serpentine is selected to obtain the most suitable HXI selection. Consult your local BAC Balticare Representative for selection assistance.

Hot Dip Galvanised Coil

Baltimore Aircoil

Finned Coil

HXI - D 9

Wet Deck Surface z

z

z

Fill pack extended into the cold water basin to avoid sound of water splash Reduction of recirculating spray water temperature results in compact prime surface coil which reduces both refrigerant and piping costs. Saturation and pre-cooling of incoming outside air

Wet Deck Surface

Fan Drive System

Individual Motor and Drive on each Fan

Extra Steps of Capacity Control

The low sound fan drive system provides the cooling air necessary to reject heat from the system to the atmosphere. The standard fan drive system consists of an independent fan motor and drive assembly per fan with a plenum partition to allow independent operation of each fan. This standard feature provides an extra step of capacity control.

Low Sound Operation The low sound levels generated by HXI Hybrid Closed Circuit Cooling Towers are due to the use of high efficiency low noise axial fans and make them suitable for installation in most environments. For extremely sound sensitive installations, factory designed, tested and rated sound attenuation is available for both the air intake and discharge. Note: For more information, please refer to the section “Technical Resources, Sound Reduction Options”. No discharge attenuator for units with Whisper Quiet Fan.

Low Noise Fans (dry coil section removed)

... because temperature matters

Water Saving Products

z

Cross flow plastic wet deck surface with integrated high efficiency drift eliminators

HXI - D 10

Combined Inlet Shields Combined Inlet shields prevent biological growth from sunlight, act as a filter for air borne impurities and debris and eliminate water splash out.

HXI

Remote Sump Execution The use of an auxiliary sump within a heated space is the most satisfactory way to protect sump water from freezing. When the circulating pump is shut off, all the water in the water distribution, in suspension and in the sump will drain freely to the auxiliary sump. Combined Inlet Shields Note: For detailed information on the calculation of the remote sump tank, please refer to the section "Technical Resources, Selection of Remote Sump Tank".

Removable Fill Bundles For installations where it is necessary or recommended to remove the wet deck surface for more thorough cleaning and disinfection, removable bundled fill is available. The fill bundles can be easily lifted and handled by one person and therefore provide a simple and secure method of removing and installing. The bundles can be dismantled and sheet by sheet can be removed for inspection and cleaning of both sides. After cleaning the sheets can be rebundled and re-installed.

Easy Removable Fill Bundles

Baltimore Aircoil

HXI - D 11

Accessories External Service Platforms For external service, platforms can be added to the unit.

Internal Ladder

Internal Service Platforms For access to the motor and drive assemblies an upper service platform with ladder and handrails is available.

External Service Platform

Basin Heaters Although most units will operate dry in the winter, basin heaters are available for freeze protection when required. Basin heaters prevent freezing of the water in the cold water basin when the unit is idle. Factory-installed heaters, which maintain the water temperature at 4°C, are a simple and inexpensive way of providing such protection.

Model No. HXI

Electric Immersion Heaters -18°C kW

HXI 42X-K

1x4

HXI 43X-L

1x6

HXI 44X-M

1x6

HXI (Q)54X-O

1x8

HXI (Q)56X-O

2x6

HXI (Q)64X-O

2x6

HXI (Q)66X-O

2x8

Electric Water Level Control Package The electric water level control replaces the standard mechanical make-up valve when a more precise water level control is required. This package consists of a float switch mounted in the basin and a solenoid activated valve in the make-up water line. The valve is slow closing to minimize water hammer.

... because temperature matters

Water Saving Products

For access to the motor and drive assemblies internal ladders are available on all models.

HXI - D 12

Flow Control Package

HXI

A flow control package is available to provide maximum plume control and water savings. This package consists of a 3-way flow control valve arrangement with actuator, and all connecting piping. The 3-way flow control valve arrangement shown below for single prime surface and double prime surface coil connections.

3-way Flow Control Valve

Single Prime Surface Coil Connections 1. Fluid in; 2. Fluid out.; (shown for 3/4, 1/1 and 1-1/2 serpentine)

Double Prime Surface Coil Connections 1. Fluid in; 2. Fluid out.

Note: For double serpentine the manifold inlet is relocated to opposite side.

Vibration Cut-out Switch A factory-mounted vibration cut-out switch is available to effectively protect against equipment failure due to excessive vibration of the mechanical equipment system. BAC can provide a vibration cut-out switch in an IP65 enclosure to ensure reliable protection.

Extended Lubrication Lines Extended lubrication lines with grease fittings are available for lubrication of the fan shaft bearings.

Basin Sweeper Piping Basin sweeper piping provides an effective method of preventing sediment from collecting in the cold water basin of the unit. A complete piping system, including nozzles, is provided in the unit basin for connection to side stream filtration equipment. Note: For more information, please refer to the section "Technical Resources, Filtration".

Baltimore Aircoil

HXI - D 13

Engineering Data REMARK: Do not use for construction. Refer to factory certified dimensions & weights. This brochure includes data current at time of publication, which should be reconfirmed at the time of purchase. In the interest of product improvement, specifications, weights and dimensions are subject to change without notice. Up-to-date engineering data and more can be found at www.BaltimoreAircoil.com.

HXI 42X - 44X

Water Saving Products

1. Inlet Connection; 2. Outlet Connection, 3. Make Up ND15, 4. Overflow ND80; 5. Drain ND50; 6. Access door.

Inlet / Outlet Coil Connections (mm)

Airflow (m3/s)

Fan Motor (kW)

Spray Water Flow (l/s)

Pump (kW)

2385 2385 2385

13,0 12,9 12,8

(1x) 7,5 (1x) 7,5 (1x) 7,5

12,0 12,0 12,0

2775 2775 2775

2385 2385 2385

20,2 19,9 19,6

(2x) 5,5 (2x) 5,5 (2x) 5,5

3690 3690 3690

2385 2385 2385

26,6 26,3 26,0

(2x) 7,5 (2x) 7,5 (2x) 7,5

Model No. HXI

Operating Weight (kg)

Shipping Weight (kg)

Heaviest Section (kg)

H (mm)

L (mm)

W (mm)

420-K 421-K 422-K

3810 4020 4230

2570 2710 2850

1110 1260 1400

4855 4855 4855

1861 1861 1861

430-L 431-L 432-L

5560 5870 6190

3700 3910 4130

1660 1870 2090

4855 4855 4855

440-M 441-M 442-M

7010 7420 7850

4520 4800 5090

1960 2240 2530

4855 4855 4855

Prime Surface Coil

Finned Coil

(1x) 1,1 (1x) 1,1 (1x) 1,1

(1x) 100 (1x) 100 (1x) 100

(2x) 80 (2x) 80 (2x) 80

18,3 18,3 18,3

(1x) 2,2 (1x) 2,2 (1x) 2,2

(1x) 100 (1x) 100 (1x) 100

(2x) 80 (2x) 80 (2x) 80

31,5 31,5 31,5

(1x) 2,2 (1x) 2,2 (1x) 2,2

(1x) 100 (1x) 100 (1x) 100

(2x) 80 (2x) 80 (2x) 80

... because temperature matters

HXI - D 14

HXI

HXI (Q)54X - HXI (Q)56X

1. Inlet Connection; 2. Outlet Connection; 3. Make Up ND25; 4. Overflow ND80; 5. Drain ND50; 6. Access door.

Inlet/Outlet Coil Connections (mm)

Model No. HXI

Operating Weight (kg)

Shipping Weight (kg)

Heaviest Section (kg)

H (mm)

L (mm)

W (mm)

Airflow (m3/s)

Fan Motor (kW)

Spray Water Flow (l/s)

Pump (kW)

540-O 541-O 542-O Q540-O Q541-O

8690 9310 9930 9930 11180

5700 6140 6580 6580 7460

2400 2840 3280 3280 4160

6580 6580 6580 6580 6580

3690 3690 3690 3690 3690

2985 2985 2985 2985 2985

35,5 35,1 34,9 34,9 34,6

(2x) 11 (2x) 11 (2x) 11 (2x) 11 (2x) 11

45,1 45,1 45,1 45,1 45,1

(1x) 4,0 (1x) 4,0 (1x) 4,0 (1x) 4,0 (1x) 4,0

(2x) 100 (2x) 100 (2x) 100 (1x) 150 (1x) 150

(2x) 80 (2x) 80 (2x) 80 (2x) 80 (2x) 80

560-O 561-O 562-O Q560-O Q561-O

12695 13635 14575 14575 16475

8220 8880 9540 9540 10880

3360 4090 4740 4740 6090

6785 6785 6785 6785 6785

5520 5520 5520 5520 5520

2985 2985 2985 2985 2985

53,6 53,1 52,7 52,7 52,3

(3x) 11 (3x) 11 (3x) 11 (3x) 11 (3x) 11

56,8 56,8 56,8 56,8 56,8

(1x) 5,5 (1x) 5,5 (1x) 5,5 (1x) 5,5 (1x) 5,5

(2x) 100 (2x) 100 (2x) 100 (1x) 150 (1x) 150

(2x) 100 (2x) 100 (2x) 100 (2x) 100 (2x) 100

Baltimore Aircoil

Prime Finned coil surface coil

HXI - D 15

HXI (Q)64X - HXI (Q)66X

Model No. HXI

Operating Shipping Weight Weight (kg) (kg)

Heaviest Section (kg)

H (mm)

L (mm)

W (mm)

Airflow (m3/s)

Inlet/Outlet Coil Connections (mm)

Fan Motor (kW)

Spray Water Flow (l/s)

Pump (kW)

Prime Surface Coil

Finned Coil

640-O 641-O 642-O Q640-O Q641-O

10050 10740 11430 11430 12790

6330 6810 7290 7290 8240

2575 3055 3535 3540 4480

6785 6785 6785 6785 6785

3690 3690 3690 3690 3690

3610 3610 3610 3610 3610

39,9 39,2 38,7 38,7 37,8

(2x) 11 (2x) 11 (2x) 11 (2x) 11 (2x) 11

45,1 45,1 45,1 45,1 45,1

(1x) 4,0 (1x) 4,0 (1x) 4,0 (1x) 4,0 (1x) 4,0

(2x) 100 (2x) 100 (2x) 100 (1x) 150 (1x) 150

(2x) 100 (2x) 100 (2x) 100 (2x) 100 (2x) 100

660-O 661-O 662-O Q660-O Q661-O

14690 15700 16710 16710 18750

9085 9795 10505 10505 11955

3710 4420 5130 5130 6570

6925 6925 6925 6925 6925

5520 5520 5520 5520 5520

3610 3610 3610 3610 3610

60,5 59,5 58,6 60,5 57,4

(3x) 11 (3x) 11 (3x) 11 (3x) 11 (3x) 11

56,8 56,8 56,8 56,8 56,8

(1x) 5,5 (1x) 5,5 (1x) 5,5 (1x) 5,5 (1x) 5,5

(2x) 100 (2x) 100 (2x) 100 (1x) 150 (1x) 150

(2x) 100 (2x) 100 (2x) 100 (2x) 100 (2x) 100

... because temperature matters

Water Saving Products

1. Inlet Connection; 2. Outlet Connection; 3. Make Up ND25; 4. Overflow ND80; 5. Drain ND50; 6. Access door.

HXI - D 16

Serpentine Arrangement Note: Only available on the finned coil.

Description:

HXI

The finned coil on the HXI unit has 6 rows. The serpentine indicates the way in which these rows are circuited internally. The serpentine influences the process fluid velocity (the smaller the serpentine, the higher the flow) and the total pressure drop over the unit ( the smaller the serpentine, the higher the finned coil pressure drop). Hence, the unit flow and pressure drop must be taken into account when the finned coil serpentine is selected to obtain the most suitable HXI selection.

Nomenclature: Affix

Example

3/4 serpentine

A

HXI 420-K A

1/1 serpentine

B

HXI 420-K B

1-1/2 serpentine

C

HXI 420-K C

Double Serpentine

D

HXI 540-O D

External finned coil arrangement: For 3/4 serpentine (A) , 1/1 serpentine (B) and 1-1/2 serpentine (C), the finned coil inlet and the outlet connections are on the same side. For double serpentine (D), the finned coil inlet connections are on the opposite side of the finned coil outlet connections.

3/4, 1/1, 1-1/2 Serpentine

Double Serpentine

General Notes 1. Pipe sizes are nominal diameters. All connections have BSP male thread except for the 15 mm vent which has female BSP thread. 2. Dimensional drawings show standard (right hand) arrangements with the standard finned coil arrangement. Left hand arrangement can be furnished by special order. 3. Coil connection locations are approximate. Dimensions should not be used for prefabrication of the connecting piping. 4. For high process flows, the double serpentine finned coil arrangement (HXI D) might be used. For a finned coil bundle with

a double serpentine arrangement, the coil inlet connections will be on one side and the outlet on the opposite side. (Refer to serpentine arrangements) 5. All technical information on this page is without manifolds and three-way valve arrangement. (refer to the section "Accessories, Flow control package) 6. The units will be delivered in 3 different pieces, upper, middle and lower section.

Baltimore Aircoil

HXI - D 17

Sound Attenuation REMARK: Do not use for construction. Refer to factory certified dimensions & weights. This brochure includes data current at time of publication, which should be reconfirmed at the time of purchase. In the interest of product improvement, specifications, weights and dimensions are subject to change without notice. Up-to-date engineering data and more can be found at www.BaltimoreAircoil.com.

Water Saving Products

1. Unit Width; 2. Unit Height; 3. Insulated Plenum; 4. Intake Attenuator.

Model No. HXI

Weight Sound Attenuator (kg)

HXI 42X

100

HXI 43X

130

HXI 44X

175

HXI (Q)54X

150

HXI (Q)56X

375

HXI (Q)64X

250

HXI (Q)66X

375

Modes of Operation Operation Mode

Dry Finned Coil Fluid Flow

Wet Prime Surface Coil Fluid Flow

Spray Pump

Fans

Dry-Wet Mode

100 %

Modulating

ON

ON

Adiabatic Mode

100 %

0%

ON

ON

Dry Mode

100 %

100 %

OFF

ON*

Note: *During dry mode air flow modulation can be controlled by two-speed motor or Variable Frequency Drive.

... because temperature matters

HXI - D 18

Combined Dry/Wet Operation Mode

HXI

In this mode, the fluid to be cooled flows first to the dry finned coil and then to the prime surface evaporative coil, where the cooled fluid exits the unit. Spray water is drawn from the cold water basin and pumped to the water distribution system above the prime surface coil. Wetting the prime surface coil allows evaporative cooling to occur. The spray water falls from the prime surface coil over the wet deck surface, enhancing the evaporative heat transfer by sub-cooling the spray water. Air is drawn through both the prime surface coil and through the wet deck surface where it is saturated and picks up heat. The air is, however, still cold enough to achieve significant cooling within the finned coil, which is installed at the discharge above the fan(s). In the dry/wet mode, both sensible and evaporative heat transfer are used. Compared to a conventional evaporative unit, the potential for plume is substantially reduced and significant water savings can be obtained, even at peak design conditions. At reduced heat load and/or ambient temperatures, the evaporative cooling portion, and hence water usage, are further reduced as the flow through the evaporative coil is gradually decreased. This is accomplished by a modulating flow control valve arrangement, which controls the outlet fluid temperature. This control arrangement automatically assures maximum use of sensible cooling in the finned coil and minimum use of evaporative cooling in the prime surface coil. The heat transfer method and flow control are arranged to achieve maximum water savings in the dry/wet mode. Plume is minimized by reducing the amount of evaporated water and the heating of the entire discharge air with the dry finned coil.

Combined Dry-Wet Operation Mode

Water Consumption

1. Water Distribution System; 2. Air In; 3. Air Out; 4. Prime Surface Coil; 5. Wet Deck Surface; 6. Finned Coil; 7. Spray Pump; 8. Sump; 9. Axial Fan.

Adiabatic Mode The adiabatic mode occurs when the fluid to be cooled completely bypasses the evaporative prime surface coil. No heat is rejected from this coil and the recirculating spray water merely serves to saturate and adiabatically pre-cool the incoming outside air. In most climates, the ambient air still has considerable potential for absorbing moisture. Thus adiabatic cooling of the incoming air results in significantly lower air temperatures, which greatly increases the rate of sensible heat transfer. Compared to conventional evaporative cooling equipment, visible plume and water consumption are greatly reduced while maintaining the low fluid design temperatures required to maximize system efficiency.

Adiabatic Operation Mode

Water Consumption

1. Water Distribution System; 2. Air In; 3. Air Out; 4. Prime Surface Coil; 5. Wet Deck Surface; 6. Finned Coil; 7. Spray Pump; 8. Sump; 9. Axial Fan.

Baltimore Aircoil

HXI - D 19

Dry Mode During the dry operation mode the spray water system is turned off, saving on pump energy. The fluid to be cooled is fed from the finned coil to the prime surface coil. The modulating flow control valve remains fully open to ensure both coils receive the full fluid flow in series; hence the maximum heat transfer surface is available. In this mode no water consumption occurs, and plume is completely eliminated. HXI units can be economically selected for dry bulb switchover points of 10°C to 15°C or higher, depending on the specific needs of the project. When the equipment operates in the dry mode for prolonged periods, draining the cold water basin is recommended, eliminating the need for freeze protection and water treatment.

Water Consumption

1. Water Distribution System; 2. Air In; 3. Air Out; 4. Prime Surface Coil; 5. Wet Deck Surface; 6. Finned Coil; 7. Spray Pump; 8. Sump; 9. Axial Fan.

... because temperature matters

Water Saving Products

Dry Operation Mode

HXI - D 20

Winter Operation

HXI

Hybrid Evaporative Fluid Cooler coil(s) must be protected from damage by freezing of the fluid inside the coil(s) when exposed to subfreezing conditions. Freeze protection can be obtained by the use of ethylene or propylene glycol or other anti-freeze solutions in appropriate concentrations. If no anti-freeze solution can be used, refer to the heat loss data hereunder and to the section Winter Operation of the HXI operating and maintenance instructions bulletin.

HXI Model N°

Minimum Flow (l/s)

Heatloss Data (kW) (1) Standard Unit

420-K 421-K 422-K

3 3 3

430-L 431-L 432-L

Coil Volumes Prime Surface Coil (l)

Finned Coil (l)

Pan Volume Operating Level (mm)

85 90 95

122 174 226

150 150 150

556 556 556

3 3 3

127 135 143

175 256 337

214 214 214

847 847 847

440-M 441-M 442-M

5 5 5

167 178 189

236 344 452

277 277 277

1137 1137 1137

540-O 541-O 542-O Q540-O Q541-O

6 6 6 12 12

210 225 240 240 270

349 510 671 716 1038

349 349 349 349 349

685 685 685 685 685

560-O 561-O 562-O Q560-O Q561-O

6 6 6 12 12

318 340 365 365 415

517 762 1052 1542 1562

533 533 533 533 533

1036 1036 1036 1036 1036

640-O 641-O 642-O Q640-O Q641-O

7 7 7 14 14

250 265 282 282 315

377 550 723 771 1117

450 450 450 450 450

785 785 785 785 785

660-O 661-O 662-O Q660-O Q661-O

7 7 7 14 14

374 397 421 421 468

558 821 1084 1132 1658

644 644 644 644 644

1187 1187 1187 1187 1187

Notes: 1. Heat loss data, based on 10°C coil water and -14°C with 20 m/s wind velocity (fans and pump off). 2. Electric immersion heaters with thermostat and low level cut out. All components are factory installed in the cooler pan. Heaters are selected to maintain +4°C pan water at -18°C ambient temperature. In outdoor locations trace heating and insulation of spray pump(s) (by others) may be required for freeze protection. See section "Accessories" for more information on Basin Heaters.

Remote Sump Data Refer to the "Technical Resources" section "Selection of Remote Sump" for Remote Sump Data.

Baltimore Aircoil

HXI - D 21

Structural Support REMARK: Do not use for construction. Refer to factory certified dimensions & weights. This brochure includes data current at time of publication, which should be reconfirmed at the time of purchase. In the interest of product improvement, specifications, weights and dimensions are subject to change without notice. Up-to-date engineering data and more can be found at www.BaltimoreAircoil.com. The recommended support arrangement for units consists of parallel I-beams running the full length of the unit, spaced as shown in the following drawing. Besides providing adequate support, the steel also serves to raise the unit above any solid foundation to ensure access to the bottom of the unit. To support units in an alternate steel support arrangement, consult your BAC Balticare Representative.

Water Saving Products

Units with and without Sound Attenuation

1. Outline of Unit, 2. Air Intake, 3. Mounting Holes diameter 22 mm, 4. Unit

Model HXI / HXIQ

Max. Deflection (mm) (4)

42X

Dimensions (mm)

N° of 16mm Anchorbolts

W

L

A

B

C

5

2385

1860

2325

-

255

4

43X

8

2385

2775

2325

-

255

4

44X

10

2385

3690

2325

-

255

4

(Q)54X

10

2985

3690

2925

-

255

4

(Q)56X

12

2985

5520

2925

2440

270

8

(Q)64X

10

3610

3690

3550

-

255

4

(Q)66X

12

3610

5520

3550

2440

270

8

Notes : 1. Support steel and anchor bolts to be designed and furnished by others. 2. All support steel must be level at the top. 3. Beams must be selected in accordance with accepted structural practice. Maximum deflection of beam under unit see table. 4. If vibration isolation rails are to be used between the unit and supporting steel, be certain to allow for the length of the vibration

rails when determining the length of the supporting steel, as vibration rail length and mounting hole locations may differ from those of the unit. 5. If point vibration isolation is used with multi-cell units, the isolators must be located under the support steel, not between the support steel and the towers.

... because temperature matters

HXI - D 22

Engineering Specifications

HXI

1.0 Closed Circuit Hybrid Cooling Tower 1.1 General: Furnish and install _____ factory-assembled, induceddraft, axial fan, closed circuit hybrid cooling tower(s) with vertical air discharge, conforming in all aspects to the specifications, schedules and as shown on the plans. The unit shall be able to operate in combined dry/wet, adiabatic and dry modes for plume abatement and minimum water consumption. Overall dimensions shall not exceed approximately _____ mm long x ______ mm wide x _____ mm high. Operating weight shall not exceed ________kg. The closed circuit hybrid cooling tower(s) shall be Baltimore Aircoil Model ____________. 1.2 Thermal Capacity: The closed circuit hybrid cooling tower(s) shall be warranted by the manufacturer to cool _____ l/s of ________% by volume aqueous ethylene/propylene glycol solution (water) from ______ °C to _____C at _____°C entering wet-bulb temperature and from ________°C to _________°C at _________°C entering dry bulb temperature. Total coil pressure drop shall not exceed __________kPa. 1.3 Corrosion Resistant Construction (standard): Unless otherwise noted in this specification, all steel panels and structural members shall be constructed of heavy-gauge Z600 metric hot-dip

galvanized steel with all edges given a protective coating of zinc-rich compound and the exterior protected with the BALTIPLUS Corrosion Protection. (Alternate 1.3) Corrosion Resistant Construction (optional): Unless otherwise noted in this specification, all steel panels and structural members shall be protected with the BALTIBOND® Corrosion Protection System. The system shall consist of Z600 metric hot-dip galvanized steel prepared in a four-step (clean, pre-treat, rinse, dry) process with an electrostatically sprayed, thermosetting, hybrid polymer fuse-bonded to the substrate during a thermally activated curing stage and monitored by a 23-step quality assurance program. 1.4 Quality Assurance: The cooling tower manufacturer shall have a Management System certified by an accredited registrar as complying with the requirements of ISO-9001:2000 to ensure consistent quality of products and services. 1.5 Warranty: The manufacturer’s standard equipment warranty shall be for a period of not less than one year from date of startup or eighteen months from date of shipment, whichever occurs first.

2.0 Construction Details 2.1. Coil Sections: The dry finned coil shall consist of copper tubes with rippled edge, aluminum flat plate fins, and headers of seamless copper tubes installed in a heavy-gauge aluminum casing. Fins shall have full drawn collars to maintain consistent fin spacing and a continuous surface contact over the entire tube for maximum heat transfer. The coil shall have a design pressure of 10 bar and be pneumatically tested at 15 bar. Staggered tube coil arrangement and fin density shall be optimized for maximum sensible heat transfer during all operation modes with minimum airside pressure drop. The prime surface coil shall be encased in a heavy-gauge galvanized steel casing. The coil shall be constructed of continuous serpentine all prime surface steel, be pneumatically tested 15 bar, and be hot-dip

galvanized after fabrication. The coil shall be designed for free drainage of fluid and shall be PED compliant. Maximum allowable working pressure shall be 10 bar. 2.2.Cold Water Basin: The cold water basin shall be constructed of heavy-gauge hot-dip galvanized steel. The basin shall include a depressed section with drain/clean-out connection. Standard accessories shall include large area, lift-out steel strainers with perforated openings sized smaller than water distribution nozzle orifices, an integral anti-vortexing hood to prevent air entrainment, waste water bleed line, and brass make-up valve with large diameter plastic float arranged for easy adjustment.

3.0 Mechanical Equipment 3.1. Fan(s): Fan(s) shall be heavy-duty, axial flow low noise, with aluminum alloy blades. Air shall discharge through a fan cylinder designed for streamlined air entry and minimum fan blade tip clearance for maximum fan efficiency. Fan(s) and shaft(s) shall be supported by heavy-duty, self-aligning, grease-packed ball bearings with moisture-proof seals and integral slinger rings, designed for minimum L10 life of 40,000 hours. Fan(s) shall be belt driven and

specifically designed for evaporative cooling service. Fan and motor sheave(s) shall be fabricated from cast aluminum. 3.2. Fan Motor: Fan motor(s) shall be totally enclosed fan cooled (TEFC), reversible, squirrel cage, ball bearing, designed specifically for evaporative cooling duty on _____ volts___ hertz ___ phase electrical service. The motor shall be furnished with special moisture protection on windings, shafts, and bearings. Each motor shall be mounted on an easily adjusted, heavy-duty motor base.

4.0 Wet Deck Surface and Drift Eliminators 4.1. BACross® Wet Deck Surface and Drift Eliminators: The wet deck surface and integral drift eliminators shall be formed from plastic material and shall be impervious to rot, decay, fungus and biological attack. The surface shall be manufactured and performance tested by the closed circuit cooling tower manufacturer to provide single source

responsibility and assure control of the final product. A separate set of drift eliminators shall be removable in easily handled sections for quick access to the coil. Eliminators shall have a minimum of three changes in air direction.

5.0 Combined Inlet Shield Technology 5.1. Combined Inlet Shields: Combined inlet shields shall be separate from the wet deck surface and removable to allow easy access for inspection of the air/water interface at the air inlet side of the equipment. Combined inlet shields shall prevent UV-light and

debris from entering the unit, as well as prevent water splash out during fan cycling. They shall be constructed of maintenance free, corrosion and UV resistant material.

Baltimore Aircoil

HXI - D 23

6.0 Access 6.1. Plenum Access: A large, hinged access door shall be provided on each end wall for access to the prime surface coil, drift eliminators,

and fan plenum section. The water make-up valve, float ball, and suction strainer shall be easily accessible.

7.0 Sound 7.1 Sound Level: To maintain the quality of the local environment, the maximum sound pressure levels (dB) measured 15 m from the

Location

63

125

250

500

cooling tower operating at full fan speed shall not exceed the sound levels detailed below.

1000

2000

4000

dB(A)

Water Saving Products

Discharge

8000

Air Inlet End Back

... because temperature matters

HXI - D 24

HXI offers Economic Advantages

HXI

HXI First Cost Benefits

Heat rejection equipment must be selected for the maximum heat load at summer peak air temperatures. In most climates peak wet-bulb temperatures are significantly lower than peak drybulb temperatures. Evaporative cooling equipment based on the ambient air wet-bulb therefore has a greater temperature driving force, thus allowing the use of lower system temperatures. This greater driving force also allows the use of less and thus more cost-effective heat transfer surface area. Since the HXI concept utilizes evaporative cooling Dry-bulb / Wet-bulb difference versus climate during peak load operation it inherently benefits zone from this advantage. Evaporatively cooled units such as the HXI have a plan area and fan kilowatt advantage over the typical air-cooled arrangement, saving on support structures and electrical hook-ups. The HXI design also avoids the corrosion and scaling that can be associated with spraying of standard air-cooled equipment on design days for additional capacity. The lower process fluid temperatures that can be achieved compared to air-cooled systems and the greatly reduced fouling factors of closed loop cooling result in lower first cost of process equipment such as chillers or refrigeration compressors. Lastly, the costs associated with plume abatement are eliminated, as the design is inherently plume-free.

HXI Operating Cost Benefits

Due to its water saving concept and Combined Flow design, the HXI offers significant operating cost benefits. Water consumption is minimized throughout the year. During peak summer operation a large amount of heat load is already transferred by the finned coil. As the ambient temperature and/or heat load drops, the amount of evaporative heat transfer is further reduced by controlling the flow through the wet coil. This reduces the evaporation loss and blow-down as well as water treatment requirements compared to conventional evaporative cooling equipment. In the “adiabatic” mode only a small amount of water is needed to saturate the air and the amount of blow-down is reduced even further. Finally in the ‘dry’ mode no water is used at all (while saving the energy associated with running the spray pump). With HXI hybrid units water savings up to 70% or more are possible. Depending on local water costs and availability, this advantage alone can pay for the equipment in as little as two years through cost savings in water use, water treatment chemicals, and higher system efficiencies. In addition, fouling potential associated with open circuit cooling towers is eliminated through both the closed loop cooling system and the Advanced Coil Technology design of the HXI, assuring peak efficiency and energy savings over time. Finally, the induced draft propeller fan design results in low fan energy requirements compared to centrifugal fan units.

Closed Circuit Cooling Systems offer the lowest fluid temperatures

Baltimore Aircoil

Typical annual distribution of ambient temperature with the three operating modes

HFL - D 1

HFL

Hybrid Closed Circuit Cooling Towers

Water Saving Products

Product Detail HFL Hybrid Closed Circuit Cooling Towers .......................................... D2 Benefits ....................................................................................................... D4 Construction Details .................................................................................. D6 Custom Features and Options .................................................................. D8 Accessories ............................................................................................... D10 Engineering Data ..................................................................................... D11 Structural Support .................................................................................. D21 Engineering Specifications ..................................................................... D23

HFL - D 2

HFL Hybrid Closed Circuit Cooling Towers Capacity

HFL

Single Cell Capacity 9 to 90 l/s (30% E.G.) at 32/27/22°C

General Description The HFL combines the air cooled and evaporative technologies in one product providing the benefit of low cooling temperature and high process efficiency in the summer with the water saving advantage of air-cooled equipment in the winter. The HFL features a unique sump concept, which offers next to the principle of “intelligent” water saving an unprecedented level of operation flexibility. Additional features, such as compactness, ease of maintenance, low height, very low operating weight and effective suppression of plume, make this product your first choice for heat rejection applications.

Key Features z

Effective suppression of plume

z

Maximum water savings

z

Operational flexibility

z

Very low operating weight

z

Ease of access and cleanability for superior maintenance

z

Compactness

Baltimore Aircoil

HFL - D 3

Water Saving Products

... because temperature matters

HFL - D 4

Benefits

HFL

Effective Suppression of Plume The finned coil(s) installed in the discharge air stream of the HFL Hybrid Closed Circuit Cooling Tower unit will raise the temperature and reduce the relative humidity of the discharge air. During wet operation this suppresses the formation of visible plume even when the relative humidity of the ambient air is high. Installation of the optional three-way valve flow control package will furthermore enhance the plume suppressing effect in that this control package ensures that at any atmospheric condition only as much evaporative cooling is applied as needed to satisfy the load requirement. Therefore the air leaving the “wet” portion of the equipment is dryer than is the case with conventional evaporative cooling equipment and has a much lower tendency to generate plume. The combination of finned discharge coil and three-way valve flow control package virtually eliminates the formation of visible plume even under extremely humid conditions. It is obvious that during the periods of dry operation no plume formation will occur.

Maximum Water Savings To achieve a maximal reduction of water consumption in a cost-effective way, it is essential to make the best use of the heat exchangers incorporated in the HFL Hybrid Closed Circuit Cooling Tower. The fluid to be cooled is first fed to the finned coil(s) and then subsequently to the prime surface coil, which can either operate in wet or dry mode. This way the finned coil contributes to the heat rejection even in the summertime, when the prime surface coil is operated wet. The addition of the finned coil heat exchange surface has a significant impact on the switch point condition. Dry operation now can occur not only in wintertime but also in spring and fall and depending on the load profile even a good portion of the summer season is suitable for dry operation. To further improve the water saving feature of the HFL a three-way valve flow control system (optional) can be integrated in the piping between the finned and the prime surface coil. This intelligent control system ensures that evaporative cooling is only applied when needed and as much as needed. This way water savings up to 60% can be achieved when compared to a conventional evaporative fluid cooler.

Operational Flexibility A critical aspect of hybrid products is the switch over from wet operation to dry operation and vice versa. In particular when during dry operation water remains in the sump, the potential danger of ice formation and subsequent damage exists in subfreezing conditions. To prevent this, manufacturers recommend draining the sump during the dry operation period. Depending on the ambient climatic conditions, sump draining may not be possible, because draining and refilling a sump requires at least several hours and hence cannot be conducted on a 24-hour cycle. To cope HFL units have been tested in subfreezing with this problem, installing a conventional conditions remote sump in a heated area inside the building is adequate, but adds complexity, costs and extra space. The HFL Hybrid Closed Circuit Cooling Tower has a unique sump design, which includes a wet and a dry sump. During dry operation all water will drain from the dry sump into the wet sump, which is shielded from the airstream. Heaters in the wet sump are sufficiently sized to prevent freezing at temperatures as low as -25°C at full speed of the fan system. Both sumps are compactly integrated into the design of the B.A.C. HFL

Baltimore Aircoil

HFL - D 5

unit. It is for the first time that the operational flexibility and safety of a remote sump arrangement has been integrated into a factory-assembled product.

Very Low Operating Weight This is achieved by the fact that the sump water content of the HFL Hybrid Closed Circuit Cooling Tower is only about one quarter of the sump water content of a conventional evaporative fluid cooler. The HFL units from B.A.C. only contain the amount of water needed to wet the prime surface coil(s). This way it is avoided that supports are designed for a dead weight created by the amount of water which is in the sump, but does not contribute to the cooling process.

Access to the wet sump is provided through rectangular access doors at the connection end of the equipment. The wet sump is separated from the dry sump by a separation panel. This permits access to the wet sump even when the fan system is in operation, which is NOT possible with conventional equipment in forced draught configuration. Make up can be inspected and sump strainers can be cleaned whilst the cooler operates. Due to the separation panel there is also no turbulence of the sump water, which in Access to wet sump conventional designs is created by the airstream. Maintenance points in the dry sump access is provided by circular access door(s) at the side of the equipment. The bottom of the dry sump is sloping so that all water sprayed over the coil (during wet operation) will drain into the wet sump. The wet sump is compact, can be drained and cleaned easily. It is also easy to disinfect the wet sump; when this should be required.

Compactness The HFL Hybrid Closed Circuit Cooling Tower has a compact design. The models have a low height and up to three fans are operated on a singe shaft with one electrical motor. Double cells can be arranged side by side with no intermediate space requirements, which allows making maximum use of the available floor space. Side by side arrangements are possible due to the fact that the access to the wet sump is at the rear end (connection end) of the equipment and that access to the dry sump only from one side is sufficient.

... because temperature matters

Water Saving Products

Ease of Access and Cleanability for Superior Maintenance

HFL - D 6

HFL

Construction Details

1. Heavy Duty Construction z

All major structural components are constructed from heavy gauge Z600 galvanised steel

4. Hight Efficiency Air Moving System z z

z

Double brake flanges are used to maximise panel and connection strength z

2. Water Distribution System z

z

Large orifice low pressure nozzles are oriented for optimum water distribution over the heat transfer surface

z

Non-corrosive spray branches Grommeted nozzles and branches allow quick removal and cleaning z

3. Drift Eliminators z

z

z

UV resistant non-corrosive material, impervious to rot, decay and biological attack Three distinct changes in air direction to reduce drift loss significantly Assembled in easy to handle sections, which can be removed for access to the equipment interior

A close coupled transition duct uniquely curved and flared Two piece fan housings for ease of fan and shaft removal.

5. Fan Shaft and Bearings

z z

Forwardly curved centrifugal fan wheels

Heavy duty self aligning relubricable ball bearings with cast iron housings Hollow shaft protection with two part epoxy coating Shafts supported by bearings at each shaft end, no intermediate bearings

6. Fan Motor (Not Shown) z

TEFC with IP 55 protection, class F insulation

z

Sized for dry operation as standard

z

Baltimore Aircoil

Location in protected area beneath the fan housing

HFL - D 7

7. Fan Drive System z

z

Belt drive

12. Evaporative Heat Transfer Coil z

8. Access z

Rectangular access door(s) at the connection end provide access to the wet sump, even if the fan system is running Rectangular access door(s) provided in the plenum section under the finned discharge coil, for easy access to the water distribution system (Optional)

z

z

Circular access door(s) at side(s) provide access to the air distribution plenum (dry sump)

z

9. Spray Water Collection (Not Shown) z

Sloping air separation and air distribution bottom panels to ensure complete drainage of spray water in the wet sump

Copper tubes with aluminium plate fins Designed for max. 10 bar operating pressure according to PED

z

Fins with full drawn collars

z

Staggered arrangement of minimum 4 circuits

Cylindrical lift out strainer of anti-vortex design

z z

11. Make-Up Arrangement z

Sloping tubes for free fluid drainage

14. Recirculating Spray Pump

10. Suction Strainer z

Designed for max. 10 bar operating pressure according to PED

13. Finned Discharge Coil (Optional) (Not shown) z

z

Prime surface tube circuits

Factory installed and set electrical float switch

z

Close Coupled, Bronze fitted, centrifugal pump Completely piped from suction strainer to the water distribution system Installed at the connection end for ease of access

... because temperature matters

Water Saving Products

z

Slow closing solenoid valve

HFL - D 8

Custom Features and Options Construction Options

HFL

z

z

Standard Construction: Steel panels and structural elements are constructed of Z600 heavy-gauge hot-dip galvanized steel protected with the Baltiplus Corrosion Protection on the outside of the unit. Optional BALTIBOND® Corrosion Protection System: The BALTIBOND® Corrosion Protection System, a hybrid polymer coating used to extend equipment life, is applied before assembly to all hot-dip galvanized steel components of the unit.

z

Optional Stainless Steel Construction: Steel panels and structural elements are constructed of stainless steel either type 304 or 316.

z

Optional Water-Contact Stainless Steel Cold Water Basin: A cost-effective alternative to an all stainless steel unit. The critical components in the cold water basin and the cold water basin itself are provided in stainless steel. The remaining components are protected with the BALTIBOND® Corrosion Protection System.

Note: See section Technical Resources, Material of Construction for more details on the materials described above.

Coil Configurations z

Standard Serpentine Coil: The standard cooling coil is constructed of continuous lengths of all prime surface steel, hot-dip galvanized after fabrication (HDGAF). The coil is designed for low pressure drop with sloping tubes for free drainage of fluid. Each coil is pneumatically tested at 10 bar and PED certified

z

Optional Stainless Steel Coil: Coils are available in Type 304 L and 316 L stainless steel for specialized applications. The Finned Discharge Coil coil is designed for low pressure drop with sloping tubes for free drainage of fluid. Stainless steel coils must be combined with the stainless steel material options or the Baltibond® Corrosion Protection System

z

Finned Discharge Coil (FDC): To enhance the water saving capability of wet-dry HFL units, finned discharge coils are added. These coils consist of copper tubes with corrugated aluminium plate fins, installed in a heavy gauge aluminium casing. All finned discharge coils have minimum four rows providing a significant heat exchange surface for dry operation. Optionally aluminium fins can be provided with pre-coated hydrophobic anti-corrosion surface treatment.

Fan Drive System The fan drive system provides the cooling air necessary to reject heat from the system to the atmosphere. Centrifugal fans, forwardly curved, are driven by matched V-belts with taper lock sheaves.

Baltimore Aircoil

HFL - D 9

The Baltiguard® Drive System

Low Sound Operation The low sound levels generated by BAC Products with centrifugal fans make them suitable for most installations. For situations when one direction is particularly sound sensitive, the unit can be oriented so that the side opposite the air inlet faces the sound-sensitive direction. Units with centrifugal fans are also available with factory designed, tested and rated sound attenuation for both the air inlet and discharge. Note: For more information, please refer to the section “Technical Resources, Sound Reduction Options”.

Electric Water Level Control Package

Factory tested HFL Sound Attenuation (Special Execution NR45 at 10 m)

HFL units are fitted with an electric water level control to allow precise water level control. This package consists of a float switch mounted in the basin and a solenoid activated valve in the makeup water line. The valve is slow closing to minimize water hammer.

... because temperature matters

Water Saving Products

The BALTIGUARD® Drive System consists of two standard single-speed fan motors and drive assemblies. One drive assembly is sized for full speed and load, and the other is sized for approximately 2/3 speed and consumes only 1/3 of the design kilowatt power. This configuration allows the system to be operated like a two-speed motor, but with the reserve capacity of a standby motor in the event of failure. As a minimum, approximately 70% capacity will be available from the low kilowatt motor, even on a design wet-bulb day. Controls and wiring are the same, as those required for a two-speed, two-winding motor. Significant energy savings are achieved when operating at low speed during periods of reduced load and/or low wet-bulb temperatures.

HFL - D 10

Accessories Basin Heaters

HFL

HFL units exposed to below freezing ambient temperatures require protection to prevent freezing of the water in the wet sump. Factory-installed heaters, which maintain the water temperature at 4°C, are a simple and inexpensive way of providing such protection. The heater package includes the heaters, a thermostat and a low level cut out switch to protect the heaters if the water level is too low. The standard electric heaters are selected for -18°C ambient temperature. Model Number HFL

Heaters (-18°C) (kW)

HFL 36 X & HFL 48 X

2x3

HFL 72 X & HFL 96 X

2x4

HFL 108 X & HFL 144 X

2x5

HFL 150 X & HFL 192 X

4x4

HFL 180 X & HFL 240 X

2x4+2x5

HFL 216 X & HFL 288 X

4x5

Discharge Hoods Discharge hoods reduce the risk of re-circulation in tight enclosures by increasing discharge air velocity, and can be used to elevate the unit discharge above adjacent walls to comply with layout guidelines. They can also be fitted with positive closure dampers and damper actuators to minimize heat loss from convection air during idle conditions. Hoods and dampers create external static pressure and fan motors must be sized accordingly.

Capacity Control To achieve maximum water saving it is recommended to run the fan system always at full speed. There may however be applications where capacity control by a change of fan speed is needed. In such cases several options are available: z Two speed motors either as Dahlander or with separate windings z Modulating fan damper controls, consisting of an aerofoil damper blade located in the discharge of each fan housing. The control package consists of a 24 Volt transformer, a damper motor actuator with end switches and a temperature controller. All components except the temperature controller are factory installed.

Flow Control Package Flow control packages are available in combination with finned discharge coils. The control package includes a three way valve and a temperature sensor and the additional connecting piping. Flow control packages enhance water saving by making intelligent use of evaporative cooling only when needed and as much as needed.

Flow Control Package

Baltimore Aircoil

HFL - D 11

Engineering Data REMARK: Do not use for construction. Refer to factory certified dimensions & weights. This brochure includes data current at time of publication, which should be reconfirmed at the time of purchase. In the interest of product improvement, specifications, weights and dimensions are subject to change without notice. Up-to-date engineering data and more can be found at www.BaltimoreAircoil.com.

HFL 36X - 48X (Single Cell Units)

Water Saving Products 1. Access; 2. Make-up; 3. Electric Float Switch; 4. Overflow; 5. Drain; 6. Water Treatment Connection; 7.Bare Coil Fluid Inlet ND100; 8. Bare Coil Fluid Outlet ND100; 9. Vent; 10. FDC Fluid Inlet ND80; 11. FDC Fluid Outlet ND80; 12. Three-Way valve; 13. Orifice; 14. Terminal Box; 15. Operating Level; 16. Overflow Level.

Dimensions (mm) Model HFL

Fan Motor (kW)

Pump Air- Spray- Ship. Oper. Heaviest Motor flow flow Weight Weight Section (kW) (m3/s) (l/s) (kg) (kg) (kg)

HFL 361-L HFL 361-M HFL 362-M HFL 363-K HFL 363-M HFL 364-M

11 15 15 7,5 15 15

0,75 0,75 0,75 0,75 0,75 0,75

12,7 13,8 13,4 10,8 13,0 12,5

9 9 9 9 9 9

2025 2035 2305 2495 2565 2835

2680 2690 3010 3350 3420 3690

HFL 482-L HFL 483-L HFL 483-M HFL 484-M

11 11 15 15

1,1 1,1 1,1 1,1

13,6 13,4 14,6 14,3

12,1 12,1 12,1 12,1

2730 3070 3080 3410

4170 4630 4640 5100

FDC

3-Way Valve Arrangement

Ship. Oper. Ship. Weight Weight Weight (kg) (kg) (kg)

F

H

L

W

2025 2035 2305 2495 2565 2825

610 610 845 1080 1080 1315

2175 2175 2410 2675 2675 2880

2730 2730 2730 2730 2730 2730

1250 1250 1250 1250 1250 1250

250 250 250 250 250 250

315 315 315 315 315 315

2730 3070 3080 3410

845 1080 1080 1315

2410 2675 2675 2880

3650 3650 3650 3650

1250 1250 1250 1250

315 315 315 315

400 400 400 400

Oper. Weight (kg)

Heaviest Section (kg)

80 80 80 80 80 80

120 120 120 120 120 120

70 70 70 70 70 70

190 190 190 190

300 300 300 300

130 130 130 130

... because temperature matters

HFL - D 12

HFL

HFL 72X - 96X (Single Cell Units)

1. Access; 2. Make-up; 3. Electric Float Switch; 4. Overflow; 5. Drain; 6. Water Treatment Connection; 7.Bare Coil Fluid Inlet ND100; 8. Bare Coil Fluid Outlet ND100; 9. Vent; 10. FDC Fluid Inlet ND80; 11. FDC Fluid Outlet ND80; 12. Three-Way valve; 13. Orifice; 14. Terminal Box; 15. Operating Level; 16. Overflow Level.

Dimension (mm) Model HFL

Fan Motor (kW)

Pump Air- Spray- Ship. Oper. Heaviest Motor flow flow Weight Weight Section (kW) (m3/s) (l/s) (kg) (kg) (kg)

HFL 722-N HFL 722-O HFL 723-L HFL 723-O HFL 724-O

18,5 22 11 22 22

1,1 1,1 1,1 1,1 1,1

22,8 24,0 19,3 23,4 22,9

17,9 17,9 17,9 17,9 17,9

4000 4020 4510 4550 5090

5495 5515 6225 6265 6935

HFL 961-P HFL 962-N HFL 962-O HFL 962-P HFL 963-O HFL 963-P HFL 964-P

30 18,5 22 30 22 30 30

2,2 2,2 2,2 2,2 2,2 2,2 2,2

28,7 24,5 25,9 28,3 25,6 27,9 27,4

24,2 24,2 24,2 24,2 24,2 24,2 24,2

4190 4700 4740 4840 5400 5500 6150

5650 6400 6440 6540 7340 7440 8430

FDC

3-Way Valve Arrangement

F

H

L

W

Ship. Weight (kg)

4000 4020 4510 4550 5090

845 845 1080 1080 1315

2410 2410 2675 2675 2880

2730 2730 2730 2730 2730

2400 2400 2400 2400 2400

420 420 420 420 420

555 555 555 555 555

270 270 270 270 270

420 420 420 420 420

180 180 180 180 180

4190 4700 4740 4840 5400 5500 6150

610 845 845 845 1080 1080 1315

2175 2410 2410 2410 2675 2675 2880

3650 3650 3650 3650 3650 3650 3650

2400 2400 2400 2400 2400 2400 2400

525 525 525 525 525 525 525

700 700 700 700 700 700 700

290 290 290 290 290 290 290

460 460 460 460 460 460 460

220 220 220 220 220 220 220

Baltimore Aircoil

Oper. Ship. Oper. Weight Weight Weight (kg) (kg) (kg)

Heaviest Section (kg)

HFL - D 13

HFL 108X - 144X (Single Cell Units)

Dimensions (mm) Model HFL

Fan Pump Air- SprayShip. Motor Motor flow flow Weight (kW) (kW) (m3/s) (l/s) (kg)

Oper. Heaviest Weight Section (kg) (kg)

FDC

F

H

L

W

Ship. Weight (kg)

3-Way Valve Arrangement

Oper. Ship. Oper. Weight Weight Weight (kg) (kg) (kg)

Heaviest Section (kg)

HFL 1081-O HFL 1081-P HFL 1082-O HFL 1082-P HFL 1083-O HFL 1083-P HFL 1084-P HFL 1084-Q

22 30 22 30 22 30 30 37

4 4 4 4 4 4 4 4

33,3 36,9 32,4 35,9 31,1 34,5 33,8 36,2

26,9 26,9 26,9 26,9 26,9 26,9 26,9 26,9

5310 5330 6050 6070 6840 6860 7660 7760

7280 7300 8250 8270 9410 9430 10360 10460

5310 5330 6050 6070 6840 6860 7660 7760

610 610 845 845 1080 1080 1315 1315

2175 2175 2410 2410 2675 2675 2880 2880

2730 2730 2730 2730 2730 2730 2730 2730

3605 3605 3605 3605 3605 3605 3605 3605

590 590 590 590 590 590 590 590

805 805 805 805 805 805 805 805

430 430 430 430 430 430 430 430

670 670 670 670 670 670 670 670

320 320 320 320 320 320 320 320

HFL 1442-O HFL 1442-P HFL 1443-O HFL 1443-P HFL 1443-Q HFL 1444-P HFL 1444-Q

22 30 22 30 37 30 37

4 4 4 4 4 4 4

33,7 37,3 32,8 36,3 39,9 35,6 38,2

36,3 36,3 36,3 36,3 36,3 36,3 36,3

7220 7240 8170 8190 8290 9160 9260

9770 9790 11080 11100 11190 12535 12635

7220 7240 8170 8190 8290 9160 9260

845 845 1080 1080 1080 1315 1315

2410 2410 2675 2675 2675 2880 2880

3650 3650 3650 3650 3650 3650 3650

3605 3605 3605 3605 3605 3605 3605

760 760 760 760 760 760 760

1055 1055 1055 1055 1055 1055 1055

510 510 510 510 510 510 510

890 890 890 890 890 890 890

340 340 340 340 340 340 340

... because temperature matters

Water Saving Products

1. Access; 2. Make-up; 3. Electric Float Switch; 4. Overflow; 5. Drain; 6. Water Treatment Connection; 7.Bare Coil Fluid Inlet ND100; 8. Bare Coil Fluid Outlet ND100; 9. Vent; 10. FDC Fluid Inlet ND100; 11. FDC Fluid Outlet ND100; 12. Three-Way valve; 13. Orifice; 14. Terminal Box; 15. Operating Level; 16. Overflow Level.

HFL - D 14

HFL

HFL 150X - 192X (Double Cell Units)

Dimensions (mm) Model HFL

Fan Motor (kW)

Pump Motor (kW)

Air- Spray- Ship. Oper. Heaviest flow flow Weight Weight Section (m3/s) (l/s) (kg) (kg) (kg)

F

H

L

W

FDC

3-Way Valve Arrangement

Ship. Oper. Ship. Weight Weight Weight (kg) (kg) (kg)

Oper. Heaviest Weight Section (kg) (kg)

HFL 1502-N 18,5+18,5 1,1+1,1 HFL 1502-O 22+22 1,1+1,1 HFL 1503-L 11+11 1,1+1,1 HFL 1503-O 22+22 1,1+1,1 HFL 1504-O 22+22 1,1+1,1

45,6 48,0 38,6 46,8 45,8

35,8 35,8 35,8 35,8 35,8

8000 8040 9020 9100 10180

10990 11030 12450 12530 13870

4000 4020 4510 4550 5090

845 845 1080 1080 1315

2410 2410 2675 2675 2880

2730 2730 2730 2730 2730

4840 4840 4840 4840 4840

840 840 840 840 840

1110 1110 1110 1110 1110

540 540 540 540 540

840 840 840 840 840

180 180 180 180 180

HFL 1921-P 30+30 2,2+2,2 HFL 1922-N 18,5+18,5 2,2+2,2 HFL 1922-O 22+22 2,2+2,2 HFL 1922-P 30+30 2,2+2,2 HFL 1923-O 22+22 2,2+2,2 HFL 1923-P 30+30 2,2+2,2 HFL 1924-P 30+30 2,2+2,2

57,4 49,0 51,8 56,6 51,2 55,8 54,8

48,4 48,4 48,4 48,4 48,4 48,4 48,4

8380 9400 9480 9680 10800 11000 12300

11300 12800 12880 13080 14680 14880 16860

4190 4700 4740 4840 5400 5500 6150

610 845 845 845 1080 1080 1315

2175 2410 2410 2410 2675 2675 2880

3650 3650 3650 3650 3650 3650 3650

4840 4840 4840 4840 4840 4840 4840

1050 1050 1050 1050 1050 1050 1050

1400 1400 1400 1400 1400 1400 1400

580 580 580 580 580 580 580

920 920 920 920 920 920 920

220 220 220 220 220 220 220

Baltimore Aircoil

HFL - D 15

HFL 180X - 240 X (Double Cell Units)

Model HFL

Pump Motor (kW)

Air- Spray- Ship. flow flow Weight (m3/s) (l/s) (kg)

Oper. Weight (kg)

Heaviest Section (kg)

F

H

L

W

FDC Ship. Weight (kg)

3-Way Valve Arrangement

Oper. Ship. Weight Weight (kg) (kg)

Oper. Heaviest Weight Section (kg) (kg)

15+30 HFL 1801-P 18,5+2 HFL 1802-O 2 HFL 1802-P 22+30 HFL 1803-P 22+30 HFL 1804-Q 22+37

1,1+4 1,1+4 1,1+4 1,1+4 1,1+4

58,7 55,2 59,9 57,9 59,1

44,8 44,8 44,8 44,8 44,8

8790 10050 10090 11410 12850

12075 13745 13785 15695 17395

5330 6050 6070 6860 7760

610 2175 2730 845 2410 2730 845 2410 2730 1080 2675 2730 1315 2880 2730

6045 6045 6045 6045 6045

1010 1010 1010 1010 1010

1360 1360 1360 1360 1360

700 700 700 700 700

1090 1090 1090 1090 1090

320 320 320 320 320

18,5+2 HFL 2402-O 2 HFL 2402-P 22+30 HFL 2403-P 22+30 HFL 2403-Q 30+37 HFL 2404-Q 30+37

2,2+4 2,2+4 2,2+4 2,2+4 2,2+4

58,2 63,2 61,9 66,8 65,6

60,5 60,5 60,5 60,5 60,5

11920 11980 13590 13790 15410

16760 16820 19030 19230 21660

7220 7240 8190 8290 9260

845 2410 3650 845 2410 3650 1080 2675 3650 1080 2675 3650 1315 2880 3650

6045 6045 6045 6045 6045

1285 1285 1285 1285 1285

1755 1755 1755 1755 1755

800 800 800 800 800

1350 1350 1350 1350 1350

340 340 340 340 340

... because temperature matters

Water Saving Products

Dimensions (mm) Fan Motor (kW)

HFL - D 16

HFL

HFL 216X - 288X (Double Cell Units)

Dimensions (mm) Model HFL

Fan Motor (kW)

Pump Air- Spray- Ship. Oper. Heaviest Motor flow flow Weight Weight Section (kW) (m3/s) (l/s) (kg) (kg) (kg)

HFL 2161-P HFL 2162-O HFL 2162-P HFL 2163-P HFL 2164-Q

30+30 22+22 30+30 30+30 37+37

4+4 4+4 4+4 4+4 4+4

73,8 64,7 71,7 69,0 72,4

53,8 53,8 53,8 53,8 53,8

10660 12100 12140 13720 15520

14600 16500 16540 18860 20920

HFL 2882-O HFL 2882-P HFL 2883-O HFL 2883-P HFL 2883-Q HFL 2884-Q

22+22 30+30 22+22 30+30 37+37 37+37

4+4 4+4 4+4 4+4 4+4 4+4

67,3 74,6 65,5 72,6 77,9 76,3

72,6 72,6 72,6 72,6 72,6 72,6

14440 14480 16340 16380 16580 18520

19540 19580 22160 22200 22380 25270

FDC

3-Way Valve Arrangement

Ship. Oper. Ship. Oper. Heaviest Weight Weight Weight Weight Section (kg) (kg) (kg) (kg) (kg)

F

H

L

W

5330 6050 6070 6860 7760

610 845 845 1080 1315

2175 2410 2410 2675 2880

2730 2730 2730 2730 2730

7250 7250 7250 7250 7250

1180 1180 1180 1180 1180

1610 1610 1610 1610 1610

860 860 860 860 860

1340 1340 1340 1340 1340

320 320 320 320 320

7220 7240 8170 8190 8290 9260

845 845 1080 1080 1080 1315

2410 2410 2675 2675 2675 2880

3650 3650 3650 3650 3650 3650

7250 7250 7250 7250 7250 7250

1520 1520 1520 1520 1520 1520

2110 2110 2110 2110 2110 2110

1020 1020 1020 1020 1020 1020

1780 1780 1780 1780 1780 1780

340 340 340 340 340 340

General Notes 1. All connections 100 mm and smaller are MPT. Connections larger than 100 mm are bevelled-for-welding. 2. Fan kW is for HFL units without FDC (0 Pa ESP) and in wet operation. To operate against external static pressure up to 125 Pa, consult your local BAC Balticare representative for size and location. 3. Airflow is for HFL units without FDC. For air flow of units equipped with the FDC consult you local BAC Balticare Representative.

4. Unit height is indicative, for precise value refer to certified print. 5. Shipping/operating weights indicated are for units without accessories such as sound attenuators, discharge hoods, etc. Consult factory certified prints to obtain weight additions and the heaviest section to be lifted. 6. The weights for the 3-way valve arrangement are the maximum weights.

Baltimore Aircoil

HFL - D 17

Sound Attenuation HS and HD Sound Attenuation

VS Sound Attenuation

1. Access; 2. FDC; 3. Discharge Attenuator; 4. Intake Attenuator VS, 5. Intake Plenum VS; 6. Three-way valve arrangement; 7. Pump Attenuation (only installed on 3000 rpm pump motors).

... because temperature matters

Water Saving Products

1. Access; 2. FDC; 3. Discharge Attenuator; 4. Intake Attenuator HS, 5. Intake Attenuator HD; 6. Three-way valve arrangement; 7. Pump Attenuation (only installed on 3000 rpm pump motors).

HFL - D 18

HFL with FDC (Finned Discharge Coil) HS attenuator

HFL

Model HFL

HD attenuator

VS attenuator

Dimensions

Solid Bottom + Intake (kg)

Discharge (kg)

Total (kg)

Solid Bottom + Intake (kg)

Discharge (kg)

Total (kg)

Total (kg)

"L" (mm)

"W" (mm)

HFL 36X-X

515

255

770

710

275

985

880

2730

1250

HFL 48X-X

515

315

830

710

335

1045

965

3650

1250

HFL 72X-X

790

420

1210

1105

455

1560

1330

2730

2400

HFL 96X-X

790

510

1300

1105

550

1655

1435

3650

2400

HFL 108X-X

1065

590

1655

1520

640

2160

1830

2730

3605

HFL 144X-X

1065

715

1780

1520

770

2290

1980

3650

3605

HFL 150X-X

1580

840

2420

2210

910

3120

2660

2730

4840

HFL 192X-X

1580

1020

2600

2210

1100

3310

2870

3650

4840

HFL 180X-X

1855

1010

2865

2625

1095

3720

3160

2730

6045

HFL 240X-X

1855

1225

3080

2625

1320

3945

3415

3650

6045

HFL 216X-X

2130

1180

3310

3040

1280

4320

3660

2730

7250

HFL 288X-X

2130

1430

3560

3040

1540

4580

3960

3650

7250

HFL without FDC (Finned Discharge Coil) HS attenuator Model HFL

Solid Bottom + Intake (kg)

Discharge (kg)

HD attenuator Total (kg)

Solid Bottom + Intake (kg)

Discharge (kg)

VS attenuator Total (kg)

Total (kg)

Dimensions "L" (mm)

"W" (mm)

HFL 36X-X

515

295

810

710

315

1025

855

2730

1250

HFL 48X-X

515

365

880

710

385

1095

950

3650

1250

HFL 72X-X

790

465

1255

1105

500

1605

1300

2730

2400

HFL 96X-X

790

565

1355

1105

605

1710

1415

3650

2400

HFL 108X-X

1065

650

1715

1520

700

2220

1800

2730

3605

HFL 144X-X

1065

785

1850

1520

840

2360

1955

3650

3605

HFL 150X-X

1580

930

2510

2210

1000

3210

2600

2730

4840

HFL 192X-X

1580

1130

2710

2210

1210

3420

2830

3650

4840

HFL 180X-X

1855

1115

2970

2625

1200

3825

3100

2730

6045

HFL 240X-X

1855

1350

3205

2625

1445

4070

3370

3650

6045

HFL 216X-X

2130

1300

3430

3040

1400

4440

3600

2730

7250

HFL 288X-X

2130

1570

3700

3040

1680

4720

3910

3650

7250

Baltimore Aircoil

HFL - D 19

Operation of the HFL "Wet/Dry" Sump Design Wet Operation

Dry Operation

During dry operation the spray water pump is shut off. The spray water drains into the “wet” sump. The sloping bottom of the plenum ensures complete drainage. In subfreezing conditions an electric sump heater located underneath the water lock will ensure that the water in the sump and in particular in the water lock area will not freeze. Air will be moved over the prime surface coil to reject the heat from the fluid fed to this coil. It is possible to consider the use of multi-step fan motors or modulating air flow controls, but if the aim is to achieve the maximum reduction of water consumption, it is recommended to maintain full airflow during “wet” operation and change fan speed only during dry operation periods.

Three Distinct Modes of Operation Combined wet/dry Operating Mode

The fluid to be cooled is first fed to the finned discharge coil, where it is pre-cooled by the discharge air. Subsequently the fluid is fed to the prime surface coil, which is wetted by the spray system. By means of evaporative heat transfer the fluid is cooled to its desired exit temperature. With this arrangement already at peak conditions significant water savings can be achieved. At reduced heat load and/or ambient temperatures the three-way valve (optional), which is controlled by the design fluid outlet temperature, modulates the flow through the wetted prime surface coil. As flow and heat load for the wetted prime surface coil decrease, less and less evaporative heat transfer will occur and a significant amount of water is saved.

Wet-Dry Operating Mode

Adiabatic Operating Mode

When the fluid to be cooled completely bypasses the wetted prime surface coil, the adiabatic operating mode occurs. In this mode no heat is rejected from the wetted prime surface coil and no water is evaporated for heat rejection purposes. The only water that evaporates is the water needed to humidify the air stream subsequently led over the finned discharge coil. Due to humidification the temperature of this air is reduced and the heat transfer capability of the finned discharge coil is increased.

... because temperature matters

Water Saving Products

The fluid to be cooled is fed to the HFL Hybrid Closed Circuit Cooling Tower. Through a water distribution system installed above the prime surface coil water is sprayed over the coil. From the coil the spray water drops into a plenum with a sloping bottom panel. The spray water is then drained to the “wet” sump, where it is collected and pumped to the water distribution system for another cycle. The sump is shielded from the air stream by a separation panel, which extends into a “water lock”. By means of the “water lock” the pressure difference between the equipment interior (elevated pressure) and the sump (atmospheric pressure) is equalised. The “water lock” is designed so that the fan(s) can be operated at any fan speed (and pressure) and maintain atmospheric pressure in the sump area. This way access to the sump is possible even if the fan system is in operation.

HFL - D 20 Dry Operating Mode

HFL

During this mode the spray water pump is off and the three-way valve is set, so that the full flow of the fluid to be cooled is fed to the prime surface coil. This way it is achieved that full benefit is taken from the heat exchange surfaces of both, the finned discharge coil and the prime surface coil, which in this mode is not wetted. In this mode no water is consumed at all.

Adiabatic Operating Mode

Dry Operating Mode

Operation Mode

Dry Finned Coil Fluid Flow

Wet Prime Surface Coil Fluid Flow

Spray Pump

Fans

Dry-Wet Mode

100 %

Modulating

ON

ON

Adiabatic Mode

100 %

0%

ON

ON

Dry Mode

100 %

100 %

OFF

ON*

Note: *During dry mode air flow modulation can be controlled by two-speed motor or Variable Frequency Drive.

Baltimore Aircoil

HFL - D 21

Structural Support REMARK: Do not use for construction. Refer to factory certified dimensions & weights. This brochure includes data current at time of publication, which should be reconfirmed at the time of purchase. In the interest of product improvement, specifications, weights and dimensions are subject to change without notice. Up-to-date engineering data and more can be found at www.BaltimoreAircoil.com. The recommended support arrangement for units consists of parallel I-beams running the full length of the unit, spaced as shown in the following drawing. Besides providing adequate support, the steel also serves to raise the unit above any solid foundation to ensure access to the bottom of the unit. To support units in an alternate steel support arrangement, consult your BAC Balticare Representative.

HFL 36X to HFL 144X (Single Cell Units)

1. (4) Ø 22 mm mounting holes; 2. Support Beams; 3. Fan Side; 4. Outline of Unit; 5. Outline of Attenuator “HS” (optional); 6. Outline of Attenuator “HD” (optional).

HFL 150X to HFL 288X (Double Cell Units)

1. (12) Ø 22 mm mounting holes; 2. Support Beams; 3. Fan Side; 4. Outline of Unit; 5. Outline of Attenuator “HS” (optional); 6. Outline of Attenuator “HD” (optional); 7. Temporary min. 500 mm extra length required (see note 5).

... because temperature matters

Water Saving Products

Units with and without Sound Attenuation

HFL

HFL - D 22

Model

A

B

C

D

Maximum Allowable Beam Deflection (mm)

HFL 36X

3334

1194

-

-

13

HFL 48X

4253

1194

-

-

13

HFL 72X

3334

2344

-

-

13

HFL 96X

4253

2344

-

-

13

HFL 108X

3334

3551

-

-

13

HFL 144X

4253

3551

-

-

13

HFL 150 X

3334

2344

2344

1951

13

HFL 192 X

4253

2344

2344

1951

13

HFL 180 X

3334

3551

2344

1951

13

HFL 240 X

4253

3551

2344

1951

13

HFL 216 X

3334

3551

3551

1951

13

HFL 288 X

4253

3551

3551

1951

13

Notes: 1. The recommended support arrangement for double cell units consists of three parallel I-beams. Supports and anchor bolts are to be designed and furnished by others. 2. All supporting beams are to be flush and level at top and must be oriented relative to gage line as shown. 3. Recommended design loads for each unit support beam should be 60% of the total unit operating weight applied as a uniform load to each of the unit beams. Beams should be designed in

accordance with standard structural practice. For the maximum allowable deflection of beams under the unit refer to above table. 4. Double Cell units in combination with omega lineair springs or vibration isolators, require a different support arrangement. Use 2x single cell arrangement positioned 500mm apart. 5. Units to be positioned +/- 500mm apart on the beams and then pushed and/or pulled together.

Baltimore Aircoil

HFL - D 23

Engineering Specifications 1.0 Hybrid Closed Circuit Cooling Tower

1.2. Thermal Capacity (water as heat transfer fluid): The hybrid closed-circuit cooling tower(s) shall be warranted by the manufacturer to cool ______lps of _______ water from ____°C to ____°C at ____°C entering wet-bulb temperature and from ____°C to ____°C at ____°C entering dry bulb temperature. (Alternate1.2.) Thermal Capacity (aqueous glycol solution as heat transfer fluid): The hybrid closed circuit cooling tower(s) shall be warranted by the manufacturer to cool ________lps of _____% by volume ethylene/propylene glycol solution from ______°C to _____°C at _____°C entering wet-bulb temperature and from ____°C to ____°C at ____°C entering dry bulb temperature. Coil pressure drop shall not exceed ________bar.

1.3. Corrosion Resistant Construction: Unless otherwise noted in this specification, all steel panels and structural members shall be constructed of heavy-gauge Z600 metric hot-dip galvanized steel, with all sheared edges given a protective coating of zinc-rich compound. (Alternate1.3.) Corrosion Resistant Construction: Unless otherwise noted in this specification, all steel panels and structural members shall be protected with the BALTIBOND®Corrosion Protection System. The system shall consist of Z600 metric hot-dip galvanized steel prepared in a four-step (clean, pre-treat, rinse, and dry) process with an electrostatically sprayed, thermosetting hybrid polymer fusebonded to the substrate during a thermally activated curing stage and monitored by a 23-step quality assurance program. 1.4. Quality Assurance: The hybrid closed circuit cooling tower manufacturer shall have a management system certified by an accredited registrar as complying with the requirements of ISO9001:2000 to ensure consistent quality of its products and services. Hybrid closed circuit cooling tower manufacturers that are not ISO9001:2000 certified shall provide an additional year of warranty to the customer at no additional cost. 1.5. Warranty: The manufacturer’s standard equipment warranty shall be for a period of not less than one year from date of startup or eighteen months from date of shipment, whichever occurs first.

2.0 Construction Details 2.1.Tower Structure: The hybrid closed circuit cooling tower shall be constructed of heavy-gauge steel utilizing double-brake flanges for maximum strength and rigidity and reliable sealing of water-tight joints. All sheared edges shall be protected with a coating of zinc-rich compound. 2.2. Casing Assembly: The hybrid closed circuit cooling tower shall include a coil casing section consisting of a serpentine coil, spray water distribution system, and drift eliminators, as indicated by the manufacturer. Drift eliminators shall be removable in easily handled sections. They shall incorporate a minimum of three changes in air direction. 2.3. Coil Assembly: 2.3.1. Prime Surface Coil: The cooling coil shall be fabricated of continuous lengths of all prime surface steel at the manufacturer’s own facility, and hot-dip galvanized after fabrication. The cooling coil shall be pneumatically tested at 10 bar. The cooling coil shall be designed for low pressure drop with sloping tubes for free drainage of fluid. 2.3.2. Finned Discharge Coil: The cooling coil shall be fabricated of copper tubes with corrugated aluminium plate fins and seamless copper tube headers with connections. The cooling coil shall be pneumatically tested at 10 bar. Fins with full drawn collars to maintain consistent fin spacing and a continuous surface contact over the entire tube. Staggered arrangement of minimum 4 circuits. Coils with heavy-duty aluminium frame shall be installed in a casing from Z600 galvanised steel. Casing includes an access plenum with access doors. 2.4. Water Distribution System: Water shall be distributed evenly over the coil at a minimum flow rate of 3.1 lps/m to ensure complete wetting of the coil at all times by large-diameter, non-clog, plastic 360°

distribution nozzles spaced across the coil face area in spray branches by snap-in rubber grommets, allowing quick removal of individual nozzles or complete branches for cleaning or flushing. Nozzles shall utilize a two-stage diffusion pattern to provide overlapping, umbrella spray patterns that create multiple intersection points with adjacent nozzles. 2.5. Spray Pump System: The hybrid closed circuit cooling tower shall include a close-coupled, bronze-fitted centrifugal pump equipped with a mechanical seal, mounted on the basin and piped to the suction strainer and water distribution system. It shall be installed so that it can be drained when the basin is drained. The pump assembly shall include a metering valve and bleed line to control the bleed rate from the pump discharge to the overflow connection. The pump motor shall be totally enclosed fan cooled (TEFC) type with IP 54 protection and class B insulation suitable for outdoor service,_____ kW, _______Volt, ________Hz, ______Phase. 2.6. Basin Assembly: The hybrid closed circuit cooling tower sump design includes a wet and a dry sump. During dry operation all water will drain from the dry sump into the wet sump, which is shielded from the airstream. Heaters in the wet sump are sufficiently sized to prevent freezing at temperatures as low as –25°C at full speed of the fan system. Both sumps are compactly integrated into the design of the hybrid closed circuit cooling tower(s). The combination sump/fan section shall be constructed of heavy-gauge Z600 metric galvanized steel. The wet sump shall be provided with large area lift out strainers with perforated openings sized smaller than the water distribution nozzles and an anti-vortexing device to prevent air entrainment. The strainer and vortex device shall be constructed of the same material as the cold water basin to prevent dissimilar metal corrosion.

... because temperature matters

Water Saving Products

1.0 General: Furnish and install ____factory assembled, forced draft, centrifugal fan, hybrid closed circuit cooling tower(s) with vertical air discharge, conforming in all aspects to the specifications and schedules as shown on the plans. Overall dimensions shall not exceed approximately ____mm long x ____mm wide x ____ mm high. The total connected fan kW shall not exceed ____kW. The total connected pump kW shall not exceed ____kW. The hybrid closed circuit cooling tower(s) shall be Baltimore Aircoil Model(s) ________________.

HFL - D 24

3.0 Mechanical Equipment

HFL

3.1. Fan System: The fans and motors shall be factory installed at the base of the unit in the dry entering air stream to provide greater reliability and ease of maintenance. The forwardly curved centrifugal fans shall be heavy-duty centrifugal flow types. Fan housings shall have curved inlet rings for efficient air entry and rectangular discharge cowls shall extend into the basin to increase fan efficiency and prevent water from entering the fans. Fans shall be mounted on a steel fan shaft supported by heavy-duty self-aligning, relubricatable ball bearings with cast iron housings and designed for a minimum L10 life of 40 000 hours (280 000 hrs average life). The fan shaft shall be protected with a two-part epoxy coating for corrosion protection.

3.2. Fan Motor/Drive System: Fan motor(s) shall be totally enclosed fan cooled (TEFC), IP-55, class F, selected for _____Pa static pressure. Fan motor(s) shall be suitable for _____ volts, ____ phase, ____ Hz electrical service and shall be mounted on an easily adjusted, heavy-duty motor base. V-belt drives and all moving parts are protected with removable screens. (Alternate 3.2.) Baltiguard® Fan System: Two single speed fan motors, one sized for full speed and load, the other sized for 2/3 speed and approximately 1/3 of full load kW shall be provided in each cell for capacity control and standby protection from drive or motor failure. Two-speed motor(s) is not an acceptable alternative.

4.0 Access 4.1. Access Wet Sump: Large rectangular access door(s) shall be provided on the connection end of the cooling tower for access to the wet sump of the cooling tower, including water make-up valve, float ball and suction strainer.

4.2. Access Dry Sump: Circular access door(s) shall be provided for easy access to the air distribution plenum. 4.3. Acces Water Distribution System: Rectangular acces doors shall be provided in the plenum section under the finned coil for easy acces to the water distribution system.

5.0 Sound 5.1 Sound Level: To maintain the quality of the local environment, the maximum sound pressure levels (dB) measured 15 m from the

Location

63

125

250

cooling tower operating at full fan speed shall not exceed the sound levels detailed below.

500

Discharge Air Inlet End Back

Baltimore Aircoil

1000

2000

4000

8000

dB(A)

DFC - D 1

DFC

Dry Fluid Coolers .

Water Saving Products

Product Detail DFC Dry Fluid Coolers ............................................................................. D2 Benefits ....................................................................................................... D4 Construction Details .................................................................................. D7 Custom Features and Options .................................................................. D9 Accessories ............................................................................................... D10 Engineering Data ..................................................................................... D12 Engineering Specifications DFCH / T ................................................... D18 Engineering Specifications DFCV ......................................................... D19

DFC - D 2

DFC Dry Fluid Coolers Capacity Single unit capacity: 30 – 1110 kW according to ENV1048 norm

DFC

1,5 – 80 l/s 34% glycol solution by volume at 40°C/35°C/25°C

General Description DFC Dry Fluid Coolers are available in horizontal, vertical or V-shaped configuration in a wide capacity and sound level range. The DFC has been designed to deliver maximum thermal performance and longevity while minimising sound pressure, operational and installation costs.

Key Features z

100 standard models – 270 models total

z

Available in horizontal, vertical or V-shaped configuration

z

Heavy duty design requiring minimum maintenance

z

Suitable for cooling of all common coolants

z

Unique retractable legs to minimise shipping and installation costs

z

Low maintenance

z

Low sound models available for sound sensitive applications

z

Optimised primary fluid pressure drops due to the availability of various tube diameters

Baltimore Aircoil

DFC - D 3

Water Saving Products

.

... because temperature matters

DFC - D 4

Benefits

DFC

Wide Capacity and Sound Level Range

Acoustical Testing on DFC Dry Cooler

z

z

z

z

Acoustical Testing on DFC Fans

The DFC Dry Fluid Cooler is available in a broad variety of fan configurations, coil designs and motor types, resulting in a wide and complete range of capacities, optimally satisfying capacity requirements and sound level limitations. Thermal and acoustical performance has been verified according to the Eurovent rating standard 7/C/003-1995 (thermal) and 8/1 (acoustical) for air cooled equipment. This assures guaranteed cooling efficiency and noise levels throughout the life of the equipment. The low speed, dry cooler range, applying a 12-pole motor, is especially designed for very sound sensitive application, such as residential areas. The application of 1/2" as well as 5/8” tubing allows the optimisation of the primary fluid pressure drop.

Capacity Testing of DFC Dry Coolers

Baltimore Aircoil

Capacity Testing of DFC Dry Coolers

DFC - D 5

Heavy Duty Design z

z

The DFC Dry Fluid Cooler has been designed to meet demanding conditions of an industrial environment. Highly corrosion resistant materials, double break flanges and intermediate coil supports guarantee strong structural strength. The heat exchanger is made of high quality seamless copper tubes with wall thickness above industrial standard and thick and rigid aluminium fins with rippled corrugated fin surface.

Heavy Duty Design, Intermediate Coil Supports

Quick and Easy Installation z

The heat exchanger section is supported by unique retractable legs, which recess into the heat transfer section to reduce shipping volume and to facilitate quick and easy installation.

Retractable Legs: in

Retractable Legs: out

... because temperature matters

Water Saving Products

Heavy Duty Design, Double-break Flanges

DFC - D 6

Low Maintenance & Ease of Access Fan and motor of the DFC Dry fluid cooler are designed to be totally maintenance free. Large removable panels assure ease of access to the heat exchanger for inspection and cleaning.

DFC

z

Removable Panels

Baltimore Aircoil

Removable Panels

DFC - D 7

Construction Details

DFCV Shaped Dry Cooler

... because temperature matters

Water Saving Products

DFCH Horizontal Dry Cooler

DFC - D 8

1. Heavy Duty Construction z

Structure and casing of bolted heavy gauge hot dipped galvanised steel panels Z275 with double break angles and intermediate coil supports. Casing painted with zinc aluminium coating.

2. Heat Exchanger (Not Shown on DFCH)

DFC

z

z

Staggered tube arrangement with dense tube spacing. Rigid 0,17 mm or 0,14 mm thick aluminium fins with rippled, corrugated fin surface design with 2,5 mm fin spacing, creates turbulent air stream for high performance.

z

High quality seamless 15,9 mm or 12,7 mm diameter copper tubes, with 0,4 mm wall thickness.

z

Thick seamless copper headers and threaded steel connections.

3. Fan & Fan Motor z

z

Low profile fan. Asymmetrically spaced and crenulated blades give low noise characteristics and increased efficiency.

z

Fan designed for frequent starting, up to 60 times an hour.

z

Continuous running at –40°C to 60°C air temperature.

z

z

The bearing seals and encapsulation of the motor eliminate the possibility of contamination, hence extending the product life. The fan and motor are designed to be totally maintenance free.

4. Retractable Legs (DFCH only) z

The heat exchanger section is supported by columns which recess into the heat exchanger section to reduce shipping volume, and facilitate installation.

5. Removable Panels (DFCH only) z

Large removable panels assure ease of access to the heat exchanger for inspection and cleaning.

6. Electrical Panel (optional) z

factory installed IP65 electrical panel fully wired to motors

z

available with variable frequency drive or step controller for capacity control

Baltimore Aircoil

DFC - D 9

Custom Features and Options Casing Construction Options Structure and casing are constructed of bolted heavy gauge hot dipped galvanised steel panels Z275 (275 gr. of zinc per m2) with double break angles and intermediate coil supports. Panels are bolted with the best hardware available on the market, triple protected against corrosion, with zinc phosphate treatment, zinc rich inorganic resin coating and aluminium rich organic topcoat. As standard the outside of the casing is painted with Baltiplus zinc aluminium polymeric coating.

The standard fan motor configuration is suitable for continuous running at –40°C to 60°C air temperature. For high temperature fluid cooling applications, where air discharge temperature may exceed 60°C, the fans can be positioned underneath the coil in the incoming air stream, pushing the air through the heat exchanger.

DFCH in High Temperature execution

Heat Exchanger Construction Materials z

z

The standard materials of construction for the heat exchanger are seamless copper tubes with 0,4-mm wall thickness and corrugated aluminium fins of 0,17 or 0,14 mm thickness and 2,5 fin spacing. For aggressive environments in industrial applications or installation at coastal areas, the following optional fin materials are available: Heat Exchanger

- Aluminium fins with pre-coated hydrophobic anti-corrosion surface treatment. Both sides of the aluminium fin are coated with a layer of epoxy phenolic resin. After thermosetting the high quality and firmly bonded hydrophobic film is highly effective in minimising salt corrosion and has excellent solvent resistance. - Copper fins of 0,2 mm thickness in lieu of aluminium.

... because temperature matters

Water Saving Products

High Temperature Configuration (DFCH only)

DFC - D 10

Accessories

DFC

Wiring to Terminal Box Each fan can be wired to a terminal box of IP55 enclosure located at the fluid connection end of the cooler, or at the opposite side. The wiring can be specified for single speed fan operation or for dual fan speed operation through delta/star reconnect.

Two-Speed Switch All motors are suitable for dual speed operation through delta/star re-connect. A two-speed switch can be supplied as an option, installed on the unit for manual changeover.

Variable Speed Drive Designed specifically for energy-optimised fan control, variable speed drive is available for the simultaneous speed control of the fans of the Dry Cooler. The variable speed drive is of EMC lownoise design, delivered with control panel and EMC filter. It has a built-in PID controller for fast and accurate control of the fans through a direct Wiring to Terminal Box connection to a temperature sensor. The drive is equipped with a manual/auto button for maintenance purposes. The drive is delivered with factory settings, but its menu-driven operating system allows easy re-programming in the field.

Safety Switch If required by local codes a safety switch for each fan can be installed in the wiring to the terminal box of the motor.

Safety Switch

Baltimore Aircoil

DFC - D 11

Starter Panels

Electrical Panel

Sound Attenuation Low Sound Dry Cooler models with low speed motors are available for installation in sound sensitive and residential areas. Alternatively the dry coolers can be equipped with air outlet silencers.

Air Inlet Screens Wire mesh screens can be factory-installed on the air intake side to prevent debris from entering the dry cooler. For dry coolers in high temperature execution, the screen would be installed at air outlet.

DFCH with Sound Attenuation

... because temperature matters

Water Saving Products

Starter panel of IP65 enclosure is available with main switch, main fuses, general contactor relay with emergency cut-out switch, control circuit fuse, thermal contactor and coil for each fan, wired to the fan motor thermostatic cut-out switch. Alternatively, starter panels designed for capacity control by fan cycling can be provided, with electronic step controller, as sequence controller with direct entry and setting of all data and immersion temperature sensor with protection pocket made of brass.

DFC - D 12

Engineering Data REMARK: Do not use for construction. Refer to factory certified dimensions & weights. This brochure includes data current at time of publication, which should be reconfirmed at the time of purchase. In the interest of product improvement, specifications, weights and dimensions are subject to change without notice. Up-to-date engineering data and more can be found at www.BaltimoreAircoil.com.

DFC

Horizontal DFCH or Vertical DFCT Dry Coolers

Horizontal DFCH Dry Cooler Note: Height for S80 models is 1527 mm.

Vertical DFCT Dry Cooler

DFCH/S80 and DFCT/S80 Standard Sound Level Models – Fans Ø 800 mm – 6 pole Motor Model DFCH/T

S8012-S213B S8012-L313B S8012-S413B S8012-L416B

Number of Fans

2 oo

Nominal Capacity kW

Airflow m3/s

Cooling Agent l/s

Δp kPa

Δ/ϒ

Δ/ϒ

Δ/ϒ

Δ/ϒ

74/64 109/91 123/101 128/105

12,2/9,3 11,4/8,7 10,7/8,2 11,3/8,6

3,9/3,4 5,7/4,8 6,5/5,3 6,7/5,5

13/10 75/54 53/36 41/29

Baltimore Aircoil

Tube Internal Surface Connecm2 tions Volume dm3 24 35 47 74

193 290 386 347

2 x ND80

Ship. Weight kg 368 401 435 473

LpA dB(A) Δ/ϒ

61/58

Dimensions mm A

B

3612 2900

C

-

DFC - D 13

Model DFCH/T

Number of Fans

Nominal Capacity kW

Airflow m3/s

Cooling Agent l/s

Δp kPa

Δ/ϒ

Δ/ϒ

Δ/ϒ

Δ/ϒ

Tube Internal Surface ConnecVolume m2 tions dm3

Ship. Weight kg

LpA dB(A) Δ/ϒ

Dimensions mm A

B

C

S8013-S213B S8013-S313B S8013-D413B S8013-S416B

3 ooo

123/104 165/138 177/146 196/161

18,3/13,9 17,1/13,0 16,1/12,3 16,9/12,9

6,5/5,5 8,7/7,3 9,3/7,7 10,3/8,5

41/30 96/69 29/21 57/40

35 53 71 112

290 435 579 520

2 x ND80

513 563 613 670

63/60

5212 4500

S8014-S213B S8014-D413B S8014-D416B

4 oooo

173/146 247/202 248/206

24,4/18,6 21,5/16,4 22,6/17,2

9,1/7,7 13,0/10,6 13,1/10,9

92/68 64/44 26/19

47 95 149

386 773 693

2 x ND80

686 820 896

63/60

6812 6100 3050

S8015-D413B S8015-M516B

5 ooooo

268/219 301/244

24,2/18,5 24,0/18,3

14,1/11,6 15,9/12,9

74/51 73/50

95 186

773 867

2 x ND80

871 1033

64/61

6812 6100 2410

S8022-S213B S8022-L313B S8022-S413B S8022-L416B

4 oo oo

149/128 218/182 247/202 257/210

24,4/18,7 22,8/17,4 21,5/16,5 22,6/17,3

7,8/6,7 11,5/9,6 13,0/10,6 13,5/11,1

13/10 75/54 53/36 41/29

47 71 95 149

386 579 773 693

4 x ND80

637 703 770 846

64/61

3612 2900

-

S8023-S213B S8023-S313B S8023-D413B S8023-S416B

6 ooo ooo

247/209 331/277 354/292 392/322

36,6/28,0 34,2/26,1 32,3/24,7 33,9/25,9

13,0/11,0 17,5/14,6 18,7/15,4 20,7/17,0

41/30 96/69 29/21 57/40

71 106 142 223

579 869 1159 1040

4 x ND80

902 1003 1103 1217

66/63

5212 4500

-

S8024-S213B S8024-D413B S8024-D416B

8 oooo oooo

346/293 494/404 497/412

48,8/37,3 43,1/33,0 45,2/34,6

18,0/15,4 26,1/21,3 26,2/21,8

92/68 64/44 26/19

95 189 298

773 1545 1386

4 x ND80

1192 1460 1612

66/63

6812 6100 3050

S8025-D413B S8025-M516B

10 ooooo ooooo

536/439 602/489

48,5/37,1 48,0/36,7

28,3/23,2 31,8/25,8

74/51 73/50

189 372

1545 1733

4 x ND80

1542 1866

67/64

6812 6100 2410

LpA dB(A)

Dimensions mm

-

Low Sound Level Models – Fans Ø 800 mm – 8 pole motor Model DFCH/T

Number of Fans

Nominal Capacity kW

Airflow m3/s

Cooling Agent l/s

Δp kPa

Tube Internal Surface Connecm2 tions Volume dm3

Δ/Y

Δ/Y

Δ/Y

Δ/Y

2 oo

73/68 90/81 100/91 104/95

9,4/8,2 8,6/7,5 8,2/7,2 8,6/7,5

3,8/3,6 4,7/4,3 5,3/4,8 5,5/5,0

69/60,2 53/44,8 36/30,7 28/24,6

24 35 47 74

193 290 386 347

L8013-S213B L8013-S313B L8013-D413B L8013-S416B

3 ooo

105/97 136/125 145/132 160/45

14,1/12,8 12,9/11,3 12,3/10,8 12,9/11,3

5,5/5,1 7,2/6,6 7,7/6,9 8,4/7,6

30/26,9 67/57,1 20/17,4 39/33,0

35 53 71 112

L8014-S213B L8014-D413B L8014-D416B

4 oooo

147/136 201/182 205/186

18,8/16,5 16,4/14,4 17,2/15,1

7,7/7,2 10,6/9,6 10,8/9,8

69/60,2 44/36,7 19/15,9

L8015-S213B L8015-D416B

5 ooooo

162/149 223/203

22,0/19,3 19,3/16,9

8,5/7,9 11,8/10,7

L8022-H213B L8022-L313B L8022-S413B L8022-L416B

4 oo oo

147/136 180/163 201/182 208/190

18,8/16,5 17,2/15,1 16,4/14,4 17,2/15,1

L8023-S213B L8023-S313B L8023-D413B L8023-S416B

6 ooo ooo

210/195 273/250 291/263 320/290

L8024-S213B L8024-D413B L8024-D416B

8 oooo oooo

L8025-S213B L8025-D416B

10 ooooo ooooo

L8012-H213B L8012-L313B L8012-S413B L8012-L416B

Ship. Weight kg

Δ/Y

A

B

C

2 x ND80

368 401 435 473

56/53

3612 2900

-

290 435 579 520

2 x ND80

513 563 613 670

57/54

5212 4500

-

47 95 149

386 773 693

2 x ND80

686 820 896

58/55

6812 6100 3050

82/71,4 22/18,5

47 186

386 867

2 x ND80

737 947

59/56

6812 6100 2410

7,7/7,2 9,5/8,6 10,6/9,6 11,0/10,0

69/60,2 53/44,8 36/30,7 28/24,6

47 71 95 149

386 579 773 693

4 x ND80

637 703 770 846

59/56

3612 2900

-

28,2/24,7 25,8/22,6 24,6/21,6 25,8/22,6

11,1/10,3 14,4/13,2 15,4/13,9 16,9/15,3

30/26,9 67/57,1 20/17,4 39/33,0

71 106 142 223

579 869 1159 1040

4 x ND80

902 1003 1103 1217

60/57

5212 4500

-

294/273 402/364 411/373

37,6/33,0 32,8/28,8 34,4/30,2

15,5/14,4 21,2/19,2 21,7/19,7

69/60,2 44/36,7 19/15,9

95 189 298

773 1545 1386

4 x ND80

1192 1460 1612

61/58

6812 6100 3050

325/299 447/406

44,0/38,6 38,7/33,9

17,1/15,8 23,6/21,5

82/71,4 22/18,5

95 372

773 1733

4 x ND80

1275 1694

62/59

6812 6100 2410

... because temperature matters

Water Saving Products

DFCH/L80 and DFCT/L80

DFC - D 14

DFCH/R80 and DFCT/R80 Ultra Low Sound Level Models – Fans Ø 800 mm – 12 pole motor

DFC

Model DFCH/T

Number of Fans

Nominal Capacity kW

Airflow m3/s

Cooling Agent l/s

Δp kPa

Δ/Y

Δ/Y

Δ/Y

Δ/Y

Tube Internal Surface Connecm2 tions Volume dm3

Ship. Weight kg

LpA dB(A) Δ/Y

Dimensions mm A

B

C

R8012-L313B

2 oo

60/48

5,0/3,7

3,1/2,5

25/17

35

290

2 x ND80

401

36/33 3612 2900

-

R8013-S313B

3 ooo

92/75

7,5/5,6

4,8/3,9

32/22

53

435

2 x ND80

563

38/35 5212 4500

-

R8014-S313B

4 oooo

126/101

10,0/7,5

6,6/5,3

73/49

71

579

2 x ND80

753

38/35 6812 6100 3050

R8022-L313B

4 oo oo

120/97

10,0/7,5

6,3/5,1

25/17

71

579

4 x ND80

703

40/36 3612 2900

-

R8023-S313B

6 ooo ooo

184/149

15,0/11,2

9,7/7,8

34/23

106

869

4 x ND80

1003

41/38 5212 4500

-

R8024-S313B

8 oooo oooo

252/202

20,0/15,0

13,3/10,6

73/49

142

1159

4 x ND80

1326

41/38 6812 6100 3050

Notes 1. Dry coolers capacities are tested according to EN 1048. 2. Ratings shown are for clean tubes with 34% ethylene glycol solution by volume, 40°C in and 35°C out, 25°C ambient air temperature.

3. Sound Pressure Levels (LpA) are measured in the horizontal plane at a distance of 10 m from the connection end of the unit, under free field conditions. 4. Dry Coolers of models with S313B, S516B and D616B coil configuration have inlet and outlet connections at opposite ends.

Sound Power Levels for one Ø 800 mm Fan at Nominal Speed Rating DFCH/T Product Range

Standard Sound Level

Low Sound Level

Ultra Low Sound Level

50 Hz

Outlet Sound Power Level at Octave Band Center Frequency (Hz)

Total

Fan Motor Conn.

63

125

250

500

1000

2000

4000

8000

LwA

6-pole

Delta

73

82

85

83

81

79

76

69

86

6-pole

Star

74

77

81

82

77

75

71

62

83

8-pole

Delta

79

80

77

76

75

74

71

65

80

8-pole

Star

76

77

74

73

72

71

68

62

77

12-pole

Delta

47

57

59

62

62

60

58

54

69

12-pole

Star

43

53

55

58

58

56

54

50

65

Sound Pressure Correction Values LpA for Other Distances For other distances the change in sound pressure depends on the dimensions of the equipment. Therefore, the correction values given in the table below are approximate values. m

2

3

5

10

15

20

30

40

50

dB(A)

+14

+10

+6

0

-4

-6

-9

-12

-14

Baltimore Aircoil

DFC - D 15

V-Shaped Dry Coolers DFCV

DFCV/S80 Standard Sound Level Models – Fans Ø 800 mm – 6 pole motor Model DFCV

Number of Fans

Nominal Capacity kW

Airflow m3/s

Cooling Agent l/s

Δp kPa

Δ/Y

Δ/Y

Δ/Y

Δ/Y

Tube Internal Surface Connecm2 tions Volume dm3

Ship. Weight kg

LpA dB(A) Δ/Y

Dimensions mm L

W

H

S8022-L413B S8022-L416B

4 oo oo

276/225 275/224

23,6/18,0 24,0/18,3

14,5/11,9 14,5/11,8

36/25 14/9

121 191

992 890

4 x ND80

916 1046

65/62 2517 2400 2775

S8023-S413B S8023-S416B

6 ooo ooo

422/344 423/346

35,4/27,0 36,0/27,5

22,3/18,1 22,3/18,3

54/37 22/15

182 287

1487 1335

4 x ND80

1283 1462

66/63 3617 2400 2775

S8024-S413B S8024-S416B

8 oooo oooo

581/472 581/471

47,2/36,0 48,0/36,6

30,7/24,9 30,7/24,9

97/68 34/23

243 382

1983 1779

8 x ND80

1677 1924

67/64 4717 2400 2775

S8025-D413B S8025-D416B

10 ooooo ooooo

685/559 685/557

59,0/45,0 60,0/45,8

36,2/29,5 36,2/29,4

31/21 13/9

303 478

2479 2224

8 x ND80

2070 2387

68/65 5817 2400 2775

S8026-D413B S8026-D416B

12 oooooo oooooo

845/688 846/692

70,8/54,1 72,0/55,0

44,6/36,3 44,7/36,6

52/35 21/15

364 574

2975 2669

8 x ND80

2464 2822

68/65 6917 2400 2775

... because temperature matters

Water Saving Products

DFCV V-shaped Dry Cooler

DFC - D 16

DFCV/L80 Low Sound Level Models – Fans Ø 800 mm – 8 pole motor

DFC

Model DFCV

Number of Fans

Nominal Capacity kW

Airflow m3/s

Cooling Agent l/s

Δp kPa

Δ/Y

Δ/Y

Δ/Y

Δ/Y

Tube Internal Surface Connecm2 tions Volume dm3

Ship. Weight kg

LpA dB(A) Δ/Y

Dimensions mm L

W

H

L8022-H413B L8022-H416B

4 oo oo

236/202 240/207

18,0/14,7 18,8/15,4

12,4/10,7 12,6/21,2

74/56 27/21

121 191

992 890

4 x ND80

916 1046

60/57 2517 2400 2664

L8023-L413B L8023-L416B

6 ooo ooo

353/302 357/310

27,0/22,1 28,2/23,1

18,6/15,9 18,9/16,4

74/56 28/22

182 287

1487 1335

4 x ND80

1283 1462

61/58 3617 2400 2664

L8024-S413B L8024-S416B

8 oooo oooo

472/405 480/415

36,0/29,5 37,6/30,8

24,9/21,4 25,3/21,9

80/60 33/25

243 382

1983 1779

4 x ND80

1677 1924

62/59 4717 2400 2664

L8025-S413B L8025-S416B

10 ooooo ooooo

601/513 615/523

45,0/36,9 47,0/38,5

31,7/27,1 32,5/27,6

124/94 46/34

303 478

2479 2224

8 x ND80

2070 2387

63/60 5817 2400 2664

L8026-D413B L8026-D416B

12 oooooo oooooo

686/587 706/608

54,0/44,2 56,4/46,2

36,3/31,0 37,3/32,1

35/26 15/11

364 574

2975 2669

8 x ND80

2464 2822

63/60 6917 2400 2664

DFCV/S90 Standard Sound Level Models – Fans Ø 900 mm – 6 pole motor Model DFCV

Number of Fans

Nominal Capacity kW

Airflow m3/s

Cooling Agent l/s

Δp kPa

Δ/Y

Δ/Y

Δ/Y

Δ/Y

Tube Internal Surface Connecm2 tions Volume dm3

Ship. Weight kg

LpA dB(A) Δ/Y

Dimensions mm L

W

H

S9022-L616B

4 oo oo

366/291

26,4/19,7

19,3/15,3

31/21

287

1335

4 x ND80

1331

59/52 2517 2400 2664

S9023-S616B

6 ooo ooo

555/436

39,6/29,6

29,3/23,0

36/23

430

2002

8 x ND80

1887

61/54 3617 2400 2664

S9024-M616B

8 oooo oooo

732/582

52,8/39,5

38,6/30,7

29/19

574

2669

8 x ND80

2490

61/54 4717 2400 2664

S9025-M616B

10 ooooo ooooo

937/733

66,0/49,4

49,5/38,7

50/32

717

3336

8x ND100

3124

62/55 5817 2400 2664

S9026-D616B

12 oooooo oooooo

1110/873

79,2/59,3

58,6/46,1

41/26

860

4004

8x ND100

3699

63/56 6917 2400 2664

Baltimore Aircoil

DFC - D 17

DFCV/R90 Ultra Low Sound Level Models – Fans Ø 900 mm – 12 pole motor Model DFCV

Number of Fans

Nominal Capacity kW

Airflow m3/s

Cooling Agent l/s

Δp kPa

Δ/Y

Δ/Y

Δ/Y

Δ/Y

Tube Internal Surface Connecm2 tions Volume dm3

Ship. Weight kg

LpA dB(A) Δ/Y

Dimensions mm L

W

H

4 oo oo

170/145 169/145

12/9,9

9,0/7,7 8,9/7,6

42/31 14/11

121 191

992 890

4 x ND80

996 1126

38/37 2517 2400 2664

R9023-L413B R9023-H416B

6 ooo ooo

255/217 260/221

18/14,8

13,5/11,5 13,7/11,7

42/31 42/32

182 287

1487 1335

4 x ND80

1403 1582

39/38 3617 2400 2664

R9024-S413B R9024-L416B

8 oooo oooo

340/290 341/294

24/19,8

18,0/15,3 18,0/15,6

38/29 27/21

243 382

1983 1779

8 x ND80

1837 2084

40/39 4717 2400 2664

R9025-S413B R9025-L416B

10 ooooo ooooo

435/368 434/371

30/24,8

23,0/19,4 22,9/19,6

71/53 51/39

303 478

2479 2224

8 x ND80

2270 2587

41/40 5817 2400 2664

R9026-D413B R9026-S416B

12 oooooo oooooo

501/432 522/444

36/29,8

26,5/22,8 27,6/23,4

21/16 40/30

364 574

2975 2669

8 x ND80

2704 3062

42/41 6917 2400 2664

Notes 1. Dry coolers capacities are tested according to EN 1048. 2. Ratings shown are for clean tubes with 34% ethylene glycol solution by volume, 40°C in and 35°C out, 25°C ambient air temperature.

3. Sound Pressure Levels (LpA) are measured in the horizontal plane at a distance of 10 m from the connection end of the unit, under free field conditions. 4. Dry Coolers of models with S313B, S516B and D616B coil configuration have inlet and outlet connections at opposite ends.

Sound Power Levels for One Fan at Nominal Speed Rating Ø 800 mm DFCV Product Range

Standard Sound Level

Low Sound Level

50Hz

Outlet Sound Power Level at Octave Band Center Frequency (Hz)

Total

Fan motor

Conn

63

125

250

500

1000

2000

4000

8000

LwA

6-pole

Delta

73

82

85

83

81

79

76

69

86

6-pole

Star

74

77

81

82

77

75

71

62

83

8-pole

Delta

79

80

77

76

75

74

71

65

80

8-pole

Star

76

77

74

73

72

71

68

62

77

Ø 900 mm DFCV Product Range

Standard Sound Level

Ultra Low Sound Level

50Hz

Outlet Sound Power Level at Octave Band Center Frequency (Hz)

Total

Fan motor Conn

63

125

250

500

1000

2000

4000

8000

LwA

6-pole

Delta

62

76

82

85

85

83

80

74

89

6-pole

Star

55

69

75

78

78

76

73

67

82

12-pole

Delta

49

58

61

64

64

62

58

55

68

12-pole

Star

48

57

60

63

63

61

57

54

67

Sound Pressure Correction Values LpA for Other Distances For other distances the change in sound pressure depends on the dimensions of the equipment. Therefore, the correction values given in the table below are approximate values. m

2

3

5

10

15

20

30

40

50

dB(A)

+14

+10

+6

0

-4

-6

-9

-12

-14

... because temperature matters

Water Saving Products

R9022-H413B R9022-H416B

DFC - D 18

Engineering Specifications DFCH / T

DFC

1.0 Heat Exchanger 1.1 General: The finned Coil Heat Exchanger consists of either 1/2” or 5/8” O.D. phosphorus deoxidised copper seamless tubes and aluminium fins. Staggered tube construction provides substantially higher capacity since more tubes are exposed to the air stream. The advanced rippled-corrugated fin design creates a state of continuous turbulence, which effectively reduces the boundary layer formation that could otherwise reduce the rate of heat exchange. Fins have full drawn collars to maintain fin spacing and provide a continuous surface cover over the entire tube. The copper tubes are mechanically expanded into the fin collars to provide a continuous

primary to secondary compression bond over the entire finned length for maximum heat transfer rates. Headers are made of seamless copper tubing and the coils are circuited for counterflow heat transfer to provide the maximum mean-effective temperature difference. The headers have steel male screw connections with 1/8” vent and drain. A full coil drain of the heat exchangers is not possible and as such Fluid Coolers operating under ambient temperatures that could drop below freezing point must contain liquid with and antifreeze agent. The entire coil block is pressure tested at 15 bar dry air submerged in warm water.

2.0 Air Movement 2.1 The air movement package: This air movement package combines premium aerodynamic and acoustic performance with innovative design to offer a compact fan and motor as an integrated product.

violet stabilised, glass coupled polypropylene airfoil section blades, designed on the latest aerospace technology.

2. Exceptionally compact design with short overall motor length.

2.4 Motor: Suitable for horizontal through to vertical shaft operation. IP55 protection, with removable drain plugs. Bearings lubricated with wide temperature range grease, re-lubricated or sealed for life depending on size. Insulation class F as standard. The motor is designed to give maximum flexibility of control by PWM Frequency Inverter, or Voltage Speed Control and where appropriate can be used to give two speeds by Delta/Star reconnect, where 80% of the full speed can be obtained by this method.

3. Two speed by delta / star reconnection speed control.

Electrical Supply

1. Crenelated blades for the 6-pole and 8-pole fans provide low noise characteristics and increased efficiencies. The adjustable pitch angle impeller of the 12-pole fans allows the optimum aerodynamic performance to be achieved for the given motor output, therefore minimising running costs.

4. Minimal moving parts for maximum reliability.

380 -420 V / 50 Hz / 3 ph 440- 480 V / 60 Hz / 3 ph

5. Motor protection IP55. Motor Electrical Details

6. Insulation Class F.

The motor can be run continuously from -40ºC to +60ºC.

7. Fan designed for frequent starting. Motor Poles

8. Continuous running from -40°C to 60°C.

Motor Rating, kW

9. Integral Overheat thermal cut-out protection. 2.2 Fan(s): The Fan has superb performance with a steep volume/ pressure performance curve, giving greater flexibility in design and making it more “tolerant” of pressure variations which may occur because of, for instance, dirt accumulation on the fins of the heat exchanger. The fan, being an integrated product of impeller and motor, is balanced as a complete unit using dynamic single plane balancing. Balance grade is G6.3. The fan and motor are designed to be totally maintenance free. 2.3 Impeller: The one-piece impellers of the 6-pole and 8-pole fans are manufactured from glass coupled engineering polymers, which are UV stabilised. These have been developed using finite element stress analysis to provide a structural hub with a smooth transition into the blade form. Crenelated blades reduce sound levels and increase efficiency. Blade section thickness, consistent with providing sufficient strength, is kept to a minimum to further reduce noise. The impeller of the 12-pole fans has an aluminium hub and clampplate with six equally spaced, fully adjustable, moulded, black, ultra-

Speed, Rpm

Full Load Current, A

Starting Current, A

6 Poles

8 Poles

12 Poles

Δ

1,50

0,76

0,25

Y

0,75

0,41

0,12

Δ

890

695

435

Y

700

570

360

Δ

5

2,50

1,80

Y

2,3

1,46

0,80

Δ

18

9,00

3,50

Y

8,3

2,60

2,90

Performance Data The air and sound performance data has been measured in accordance with the following Standards: ISO 5801:1977, type A installation test method for air performance (dual numbered BS 848 Part1: 1997) BS 848 Part 2:1985, type A installation, method of noise testing.

3.0 Supporting Frame and Casing 3.1 Frame and Casing: The supporting Frame and Casing is an allbolted painted galvanised steel construction designed to withstand

the most adverse weather conditions. Double brake flanges maximise strength of panels. Full baffles separate individual fan sections.

Baltimore Aircoil

DFC - D 19

Engineering Specifications DFCV 1.0 Heat Exchanger primary to secondary compression bond over the entire finned length for maximum heat transfer rates. Headers are made of seamless copper tubing and the coils are circuited for counterflow heat transfer to provide the maximum mean-effective temperature difference. The headers have steel male screw connections with 1/8” vent and drain. A full coil drain of the heat exchangers is not possible and as such Fluid Coolers operating under ambient temperatures that could drop below freezing point must contain liquid with an antifreeze agent. The entire coil block is pressure tested at 15 bar dry air submerged in warm water.

2.0 Air Movement 2.1 The air movement package: This air movement package combines premium aerodynamic and acoustic performance with innovative design to offer a compact fan and motor as an integrated product.

Electrical Supply

1. Crenelated blades for the 800mm diameter fans provide low noise characteristics and increased efficiencies. The adjustable pitch angle impeller of the 900mm diameter fans, allows the optimum aerodynamic performance to be achieved for the given motor output, therefore minimising running costs.

Motor Electrical Details

2. Exceptionally compact design with short overall motor length. 3. Two speed by delta / star reconnection speed control.

380 -420 V / 50 Hz / 3 ph 440- 480 V / 60 Hz / 3 ph The motor can be run continuously from -40ºC to +60ºC. A. Fans 800 mm Motor Poles Motor Rating, kW

4. Minimal moving parts for maximum reliability. Speed, Rpm

5. Motor protection IP55. 6. Insulation Class F.

Full Load Current, A

7. Fan designed for frequent starting. 8. Continuous running from -40ºC to 60ºC. 9. Integral, overheat thermal cut-out protection.

Starting Current, A

2.2 Fan(s): The Fan has superb performance with a steep volume/ pressure performance curve, giving greater flexibility in design and making it more “tolerant” of pressure variations which may occur because of, for instance, dirt accumulation on the fins of the heat exchanger. The fan, being an integrated product of impeller and motor, is balanced as a complete unit using dynamic single plane balancing. Balance grade is G6.3. The fan and motor are designed to be totally maintenance free. 2.3 Impeller: The one-piece impeller of the 800mm diameter fans is manufactured from glass coupled engineering polymers, which are UV stabilized. These have been developed using finite element stress analysis to provide a structural hub with a smooth transition into the blade form. Crenelated blades reduce sound levels and increase efficiency. Blade section thickness, consistent with providing sufficient strength, is kept to a minimum to further reduce noise. The impeller of the 900mm diameter fans has an aluminum hub and clamp-plate, with six equally spaced, fully adjustable, moulded, black, ultra violet stabilized, glass coupled polypropylene airfoil section blades, designed on the latest aerospace technology. 2.4 Motor: Suitable for horizontal through to vertical shaft operation. IP55 protection, with removable drain plugs. Bearings lubricated with wide temperature range grease, re-lubricated or sealed for life depending on size. Insulation class F as standard. The motor is designed to give maximum flexibility of control by PWM Frequency Inverter, or Voltage Speed Control and where appropriate can be used to give two speeds by Delta/Star reconnect, where 80% of the full speed can be obtained by this method.

6 Poles

8 Poles

Δ

1,50

0,76

Y

0,75

0,41

Δ

890

695

Y

700

570

Δ

5

2,50

Y

2,3

1,46

Δ

18

9,00

Y

8,3

2,60

6 Poles

12 Poles

Δ

2,10

0,25

Y

1,10

0,12

B. Fans 900 mm Motor Poles Motor Rating, kW

Speed, Rpm

Full Load Current, A

Starting Current, A

Δ

925

435

Y

725

360

Δ

5,74

1,80

Y

3,80

0,80

Δ

24,0

3,50

Y

18,4

2,90

Performance Data The air and sound performance data has been measured in accordance with the following Standards: ISO 5801:1977, type A installation test method for air performance (dual numbered BS 848 Part1: 1997) BS 848 Part 2:1985, type A installation, method of noise testing.

3.0 Supporting Frame and Casing 3.1 Frame and Casing: The supporting Frame and Casing is an allbolted painted galvanised steel construction designed to withstand

the most adverse weather conditions. Double brake flanges maximise strength of panels. Full baffles separate individual fan sections.

... because temperature matters

Water Saving Products

1.1 General: The finned Coil Heat Exchanger consists of either 1/2” or 5/8” O.D. phosphorus deoxidised copper seamless tubes and aluminium fins. Staggered tube construction provides substantially higher capacity since more tubes are exposed to the air stream. The advanced rippled-corrugated fin design creates a state of continuous turbulence, which effectively reduces the boundary layer formation that could otherwise reduce the rate of heat exchange. Fins have full drawn collars to maintain fin spacing and provide a continuous surface cover over the entire tube. The copper tubes are mechanically expanded into the fin collars to provide a continuous

DFCV-AD - D 1

DFCV-AD

TrilliumSeries Coolers

Water Saving Products

Product Detail TrilliumSeries Coolers .............................................................................. D2 Benefits ....................................................................................................... D4 Construction Details .................................................................................. D7 Custom Features and Options .................................................................. D8 Accessories ................................................................................................. D9 Engineering Data ..................................................................................... D10 Engineering Specifications TrilliumSeries Coolers .............................. D12

DFCV-AD - D 2

TrilliumSeries Coolers Capacity Single unit capacity: 220 – 1620 kW according to ENV1048 norm

DFCV-AD

12 – 86 l/s 34% glycol solution by volume at 40°C/35°C/25°C

General Description In conditions where the design fluid outlet temperature comes close to the ambient dry bulb temperature, dry air cooling becomes inefficient or impossible. The BAC TrilliumSeries Cooler has been designed to offer reliable, safe and efficient fluid cooling down to temperature below ambient temperature, while minimizing water consumption. The TrilliumSeries Cooler offers the advantages of evaporative cooling in a safe dry cooling product.

Key Features z

15 standard models, 34 models total

z

Heavy duty design requiring minimum maintenance

z

Suitable for cooling of all common coolants

z

Low maintenance

z

Low sound models available for sound sensitive applications

z

Optimised primary fluid pressure drops due to the availability of various tube diameters

z

Thermal efficiency, operational safety and unique water saving capability combined into single product

Baltimore Aircoil

DFCV-AD - D 3

Water Saving Products

.

... because temperature matters

DFCV-AD - D 4

Benefits

DFCV-AD

.

High Thermal Performance z

z

The TrilliumSeries Cooler is a V-type dry cooler equipped with unique adiabatic air pre-cooling sections, which greatly enhance the cooler’s capacity, reducing cooler’s size and allowing process temperatures to be cooled far below ambient temperature. Only when necessary (at high ambient temperatures), the adiabatic pre-cooling will be activated. The adiabatic pre-cooling sections consist of a full stainless steel frame, with water distribution outside the airflow, and highly efficient evaporative cooling medium. During adiabatic operation, the evaporative medium is wetted with water, which is evenly distributed over the top of the medium at city water pressure. As the air passes through the pads, water is evaporated in the air, and the air is humidified and cooled down to temperatures at 2 to 3 °C above wet bulb temperature.

Principle of Operation TrilliumSeries Cooler

SST Frame with Adiabatic Pre-Cooling Pads

1. Dry Heat Exchanger Coil; 2. Fluid inlet; 3. Fluid outlet; 4. Axial Fans; 5. High Efficient Evaporative Cooling Pad; 6. Water inlet Connections; 7. Water outlet Connections; 8. Adiabatic Cooling of Ambient Air; 9. Air Discharge; 10. Air in.

Baltimore Aircoil

DFCV-AD - D 5

Water Saving z

Operational Safety z

z

z

z

Water Consumption

While part of the water distributed over the 1. Evaporative Cooling; 2. Hybrid Cooling; 3. TrilliumSeries adiabatic pre-cooling medium evaporates to cool the air, excess water assists in rinsing the pads to keep it free from debris and minerals that would stay behind on the pad after evaporation. The pre-cooling system of the TrilliumSeries Cooler is designed as once-through system. The excess water leaves the adiabatic section via a gutter system to the sewer, avoiding stagnant water conditions and avoiding water re-circulation, both conditions that would increase the risk for micro-biological contamination and proliferation. After each adiabatic pre-cooling cycle, the adiabatic controls will open drain valves guaranteeing full emptying and drying of all pre-cooling water distribution piping installed on the cooler. The special pre-cooling medium design guarantees that no droplets, nor aerosols are being generated while pre-cooling is activated. Water carry-over from the pre-cooling section to the dry coil is avoided.

Limited Maintenance z

Unlike dry coolers equipped with spray systems, the TrilliumSeries Cooler provides stable and predictable thermal performance without the need for high pressure pumps and water treatment.

Installation of Pre-Cooler Medium

Installation of Pre-Cooler Medium

... because temperature matters

Water Saving Products

The TrilliumSeries Cooler is delivered with intelligent adiabatic controls limiting water consumption to very short periods of time, activating adiabatic pre-cooling in two stages and only when necessary. When compared to a traditional evaporative cooling installation, without built-in hybrid technology and controls, the TrilliumSeries Cooler saves more than 85% of the water.

DFCV-AD - D 6

DFCV-AD

z

The pre-cooling medium can be removed during colder seasons. If kept in place however, the adiabatic pre-cooling could be used to enhance energy saving operation and it acts as filter, protecting the dry coil year-round from any air borne debris which could cause coil contamination.

Installation of Water Distribution Pad

Baltimore Aircoil

Installation of Top Bar

DFCV-AD - D 7

Construction Details

1. Heavy Duty Construction z

Structure and casing of bolted heavy gauge hot dipped galvanised steel panels Z275 with double break angles and intermediate coil supports. Casing painted with zinc aluminium coating.

z

Full baffles separate individual fan sections.

z

Continuous running at –40°C to 60°C air temperature.

z

The bearing seals and encapsulation of the motor eliminate the possibility of contamination, hence extending the product life.

z

The fan and motor are designed to be totally maintenance free.

4. Adiabatic Pre-cooler

2. Heat Exchanger (Not Shown) z

Staggered tube arrangement with dense tube spacing.

z

Casing in bolted heavy gauge stainless steel.

z

Rigid 0,17 mm or 0,14 mm thick aluminium fins with rippled, corrugated fin surface design with 2,5 mm fin spacing, creates turbulent air stream for high performance.

z

Water distribution outside the airflow.

z

Water collecting sump, draining water, once through to sewage.

z

High quality seamless 15,9 mm or 12,7 mm diameter copper tubes, with 0,4 mm wall thickness.

z

Highly efficient impregnated cellulose paper evaporative cooling pad.

z

Thick seamless copper headers and threaded steel connections.

5. Electrical Panel and Adiabatic Controls

3. Fan & Fan Motor z

Low profile fan.

z

Asymmetrically spaced and crenulated blades give low noise characteristics and increased efficiency.

z

Fan designed for frequent starting, up to 60 times an hour.

z

Factory installed electrical panel of IP55 enclosure, including main isolating power switch with lock provision, magnetic main switch, emergency cut-out switch, thermal contactor with coil for each fan wired to the fan motor thermostatic cut-out switch and 400/230 transformer, Variable Frequency Drive or Step Controller for capacity control, delivered with integrated adiabatic controls.

... because temperature matters

Water Saving Products

TrilliumSeries Cooler

DFCV-AD - D 8

Custom Features and Options Heat Exchanger Construction Materials

DFCV-AD

z

z

The standard materials of construction for the heat exchanger are seamless copper tubes with 0,4-mm wall thickness and corrugated aluminium fins of 0,17 or 0,14 mm thickness and 2,5 fin spacing. For aggressive environments in industrial applications or installation at coastal areas the option of aluminium fins with pre-coated hydrophobic anti-corrosion surface treatment is Heat Exchanger available. Both sides of the aluminium fin are coated with a layer of epoxy phenolic resin. After thermosetting the high quality and firmly bonded hydrophobic film is highly effective in minimising salt corrosion and has excellent solvent resistance.

Baltimore Aircoil

DFCV-AD - D 9

Accessories Safety Switch If required by local codes a safety switch for each fan can be installed next to the respective fan and it is fully wired.

Control Panel

Control Panel with Variable Frequency Drive and Integrated Adiabatic Controls

Control Panel with Step Controller and Integrated Adiabatic Controls

... because temperature matters

Water Saving Products

TrilliumSeries Coolers are delivered with factory installed control panel, including main isolating power switch with lock provision, magnetic main switch, emergency cut-out switch, thermal contactor with coil for each fan wired to the fan motor thermostatic cut-out switch, 380/200 transformer, Variable Frequency Drive or Step Controller and integrated adiabatic controls. Each adiabatic pre-cooling side is controlled separately in function of a logical combination of ambient temperature and fluid outlet temperature. The adiabatic control sequence guarantees maximum water savings, and all adiabatic set points are adjustable.

DFCV-AD - D 10

Engineering Data

DFCV-AD

REMARK: Do not use for construction. Refer to factory certified dimensions & weights. This brochure includes data current at time of publication, which should be reconfirmed at the time of purchase. In the interest of product improvement, specifications, weights and dimensions are subject to change without notice. Up-to-date engineering data and more can be found at www.BaltimoreAircoil.com.

1. Fluid inlet connections; 2. Fluid outlet connections; 3. Pre-cooler water drain and overflow; 4. Electrical panel; 5. Pre-cooler city water connection.

Standard Sound Level Models – Fans Ø 900 mm – 6 pole motor Model DFCV-AD

Number of Fans

Operating Weight kg

Shipping Weight kg

Heaviest Section kg

Dimensions mm

Air Flow m3/s

H

L

W

Δ/Y

Tube Internal Volume dm3

Surface m2

Connections

S9022-L613B-AD S9022-L616B-AD

4 oo oo

1677 1868

1345 1448

1228 1331

2635

2546

2904

23,6/17,7 24/18

182 288

1488 1336

4 x ND80

S9023-S613B-AD S9023-S616B-AD

6 ooo ooo

2399 2692

1901 2057

1731 1887

2635

3646

2904

35,4/26,6 36/27

272 432

2232 2004

8 x ND80

S9024-M613B-AD S9024-M616B-AD

8 oooo oooo

3178 3564

2514 2724

2280 2490

2635

4746

2904

47,2/35,4 48/36

364 576

2976 2668

8 x ND80

S9025-D613B-AD S9025-D616B-AD

10 ooooo ooooo

3979 4466

3149 3411

2862 3124

2635

5878

2904

59/44,3 60/45

456 716

3720 3336

8 x ND100

S9026-D613B-AD S9026-D616B-AD

12 oooooo oooooo

4719 5309

3723 4032

3383 3699

2635

6918

2904

70,8/53,1 72/54

548 860

4464 4004

8 x ND100

Baltimore Aircoil

DFCV-AD - D 11

Ultra Low Sound Level Models – Fans Ø 900 mm – 12 pole motor Model DFCV-AD

Number of Fans

Operating Weight kg

Shipping Weight kg

Heaviest Section kg

Dimensions mm

Air Flow m3/s

H

L

W

Δ/Y

Tube Internal Volume dm3

Surface m2

Connections

4 oo oo

1367 1567

1113 1243

996 1126

2630

2546

2904

11,2/9,3

121 191

992 890

4 x ND80

R9023-L413B-AD R9023-H416B-AD

6 ooo ooo

2244 1960

1752 1573

1582 1403

2630

3646

2904

16,8/13,9

182 287

1487 1335

4 x ND80

R9024-S413B-AD R9024-L416B-AD

8 oooo oooo

2966 2580

2318 2071

2084 1837

2630

4746

2904

22,4/18,5

243 382

1983 1779

8 x ND80

R9025-D413B-AD R9025-L416B-AD

10 ooooo ooooo

3690 3198

2874 2520

2587 2270

2630

5878

2904

28,0/23,2

303 478

2479 2224

8 x ND80

R9026-D413B-AD R9026-S416B-AD

12 oooooo oooooo

3818 4386

3044 3402

2704 3062

2630

6918

2904

33,6/27,8

364 574

2975 2669

8 x ND80

Notes 1. Adiabatic cooler capacities are tested according to EN 1048 for dry coolers. 2. Ratings shown are for clean tubes with 34% ethylene glycol solution by volume, 40°C in and 35°C out, 25°C ambient air temperature.

3. Sound Pressure Levels (LpA) are measured in the horizontal plane at a distance of 10 m from the connection end of the unit, under free field conditions. 4. TrilliumSeries Coolers of models with D616B coil configuration have inlet and outlet connections at opposite ends. 5. Adiabatic pre-cooling sections are shipped separately and need to be installed on site.

Sound Power Levels for one fan at nominal speed rating DFCV-AD Product Range

Standard Sound Level

Ultra Low Sound Level

Fan Motor

50Hz

Outlet Sound Power Level at Octave Band Center Frequency (Hz)

Total

Conn.

63

125

250

500

1000

2000

4000

8000

LwA

6-pole

Delta

62

76

82

85

85

83

80

74

89

6-pole

Star

55

69

75

78

78

76

73

67

82

12-pole

Delta

49

58

61

64

64

62

58

55

68

12-pole

Star

48

57

60

63

63

61

57

54

67

Sound Pressure Correction Values LpA for Other Distances For other distances the change in sound pressure depends on the dimensions of the equipment. Therefore, the correction values given in the table below are approximate values. m

2

3

5

10

15

20

30

40

50

dB(A)

+14

+10

+6

0

-4

-6

-9

-12

-14

... because temperature matters

Water Saving Products

R9022-H413B-AD R9022-H416B-AD

DFCV-AD - D 12

Engineering Specifications TrilliumSeries Coolers

DFCV-AD

1.0 Heat Exchanger 1.1 General: The finned Coil Heat Exchanger consists of either 1/2” or 5/8” O.D. phosphorus deoxidised copper seamless tubes and aluminium fins. Staggered tube construction provides substantially higher capacity since more tubes are exposed to the air stream. The advanced rippled-corrugated fin design creates a state of continuous turbulence, which effectively reduces the boundary layer formation that could otherwise reduce the rate of heat exchange. Fins have full drawn collars to maintain fin spacing and provide a continuous surface cover over the entire tube. The copper tubes are mechanically expanded into the fin collars to provide a continuous

primary to secondary compression bond over the entire finned length for maximum heat transfer rates. Headers are made of seamless copper tubing and the coils are circuited for counterflow heat transfer to provide the maximum mean-effective temperature difference. The headers have steel male screw connections with 1/8” vent and drain. A full coil drain of the heat exchangers is not possible and as such fluid Coolers operating under ambient temperatures that could drop below freezing point must contain liquid with an antifreeze agent. The entire coil block is pressure tested at 15 bar dry air submerged in warm water.

2.0 Air Movement 2.1 The air movement package: This air movement package combines premium aerodynamic and acoustic performance with innovative design to offer a compact fan and motor as an integrated product. 1. Adjustable pitch angle impeller allows the optimum aerodynamic performance to be achieved for the given motor output, therefore minimising running costs. 2. Exceptionally compact design with short overall motor length. 3. Two speed by delta / star reconnection speed control. 4. Minimal moving parts for maximum reliability. 5. Motor protection IP55.

2.4 Motor: Suitable for horizontal through to vertical shaft operation. IP55 protection, with removable drain plugs. Bearings lubricated with wide temperature range grease, re-lubricated or sealed for life depending on size. Insulation class F as standard. The motor is designed to give maximum flexibility of control by PWM Frequency Inverter, or Voltage Speed Control and where appropriate can be used to give two speeds by Delta/Star reconnect, where 80% of the full speed can be obtained by this method. Electrical Supply 380 -420 V / 50 Hz / 3 ph 440- 480 V / 60 Hz / 3 ph Motor Electrical Details The motor can be run continuously from -40ºC to +60ºC.

6. Insulation Class F.

Motor Poles

7. Fan designed for frequent starting.

Motor Rating, kW

8. Continuous running from -40ºC to 60ºC. 9. Integral Overheat thermal cut-out protection.

Speed, Rpm

2.2 Fan(s): The Fan has superb performance with a steep volume/ pressure performance curve, giving greater flexibility in design and making it more “tolerant” of pressure variations which may occur because of, for instance, dirt accumulation on the fins of the heat exchanger. The fan, being an integrated product of impeller and motor, is balanced as a complete unit using dynamic single plane balancing. Balance grade is G6.3. The fan and motor are designed to be totally maintenance free. 2.3 Impeller: The impeller has an aluminium hub and clamp-plate, with six equally spaced, fully adjustable, moulded, black, ultra-violet resistant, glass coupled polypropylene airfoil section blades, designed on the latest aerospace technology. All rotating aluminium components are X-ray examined prior to machining to ensure quality.

Full Load Current, A

Starting Current, A

6 Poles

12 Poles

Δ

2,1

0,25

Y

1,1

0,12

Δ

925

435

Y

725

360

Δ

5,74

1,80

Y

3,8

0,80

Δ

24,0

3,50

Y

18,4

2,90

Performance Data The air and sound performance data has been measured in accordance with the following Standards: ISO 5801:1977, type A installation test method for air performance (dual numbered BS 848 Part1: 1997) BS 848 Part 2:1985, type A installation, method of noise testing.

3.0 Supporting Frame and Casing 3.1 Frame and Casing: The supporting Frame and Casing is an allbolted painted galvanised steel construction designed to withstand

the most adverse weather conditions. Double brake flanges maximise strength of panels. Full baffles separate individual fan sections.

Baltimore Aircoil

DFCV-AD - D 13

4.0 Adiabatic Pre-Cooler through the pad evaporates most of the water. Any remaining water assists in washing the pad, and is drained to the gutter. In addition scaling is kept to a minimum and no water carry-over occurs due to the fact that the water is directed to the air inlet side of the pad and this where the evaporation takes place. The air that leaves the pad is therefore cooled and humidified simultaneously without any external energy supply, and without formation of aerosols. For proper Legionella bacteria control, the system and all its water distribution piping is completely drained and dried after each adiabatic cycle. 4.2 Adiabatic Pre-Cooling Casing: The adiabatic pre-cooling casing is made of stainless steel, designed as a direct water system, without the need for pumps.

5.0 Electrical Panel and Controls 5.1 TrilliumSeries Cooler delivered with factory installed electrical panel with step controller: For TrilliumSeries Coolers delivered with factory installed electrical panel including step controller, the TrilliumSeries Cooler will be delivered with panel of IP65 enclosure, including main isolating power switch with lock provision, main fuses, emergency cut-out switch, thermal contactor with coil for each fan, wired to the fan motor thermostatic cut-out switch, 400/230 transformer, all wiring from the electrical panel to the individual fans, step controller and ambient temperature sensor. Both process fluid outlet temperature and ambient temperature signals are fed into the step controller. The adiabatic pre-cooling will be activated and stopped on the basis of a pre-programmed logical combination of the two signals in the step controller. 5.2 TrilliumSeries Cooler delivered with factory installed electrical panel with variable frequency drive: For TrilliumSeries Coolers delivered with factory installed electrical panel including

variable frequency drive, the TrilliumSeries Cooler will be delivered with panel of IP55 enclosure, including main isolating power switch with lock provision, main fuses, emergency cut-out switch, thermal contactor with coil for each fan wired to the fan motor thermostatic cut-out switch, 400/230 transformer. Danfoss Variable Frequency Drive with built-in RFI filters protected to 1st environment and EN55011 to 1B, built-in DC Link coils which reduce harmonic distortion. Hand-Off-Auto function - fast and easy commissioning. Local control Panel - clear text display read-out. Inverter by-pass power switch. Digital controller, and ambient temperature sensor. Both fan speed signal from variable speed drive and ambient temperature signal are fed to the digital controller. The adiabatic precooling will be activated and stopped on the basis of a preprogrammed logical combination of the two signals in the digital controller.

... because temperature matters

Water Saving Products

4.1 Adiabatic Pre-Cooling Medium: The MUNTERS EPACC™ adiabatic pre-cooling section serves as an adiabatic saturator to cool the incoming air. It consists of specially impregnated and corrugated cellulose paper sheets with different flute angles, one steep and one shallower that have been bonded together. Such a design yields a cooling pad with high evaporation efficiency while still operating with a very low-pressure drop. The impregnation procedure for the cellulose paper ensures a strong self supporting product, with high absorbency, which is protected against decomposition and rotting. The evaporative fluid, such as city water, is supplied to a distribution manifold and the rate of the water flow may be initially regulated by a manual-regulating valve. A distribution pad on the top of the cooling pad ensures an even water distribution and minimises the risk of dry spots. The water flows down the corrugated surface of the evaporative cooling pad. The incoming warm and dry air that passes

DCV-AD - D1

DCV-AD

TrilliumSeries Condensers

Water Saving Products

Product Detail TrilliumSeries Condensers ....................................................................... D2 Benefits ....................................................................................................... D4 Construction Details .................................................................................. D7 Custom Features and Options .................................................................. D8 Accessories ................................................................................................. D9 Engineering Data ..................................................................................... D10 Engineering Specifications TrilliumSeries Condensers ....................... D12

DCV-AD - D2

TrilliumSeries Condensers Capacity Single unit capacity:

DCV-AD

340 – 1030 KW

General Description In conditions where the design refrigerant outlet temperature comes close to the ambient dry bulb temperature, dry air cooling becomes inefficient or impossible. The BAC TrilliumSeries Condenser has been designed to offer reliable, safe and efficient gaz cooling down to temperature below ambient temperature, while minimizing water consumption. The TrilliumSeries Condenser offers the advantages of evaporative cooling in a safe dry cooling product.

Key Features z

10 standard models

z

Heavy duty design requiring minimum maintenance

z

Suitable for cooling of all common refrigerants

z

Low maintenance

z

Thermal efficiency, operational safety and unique water saving capability combined into single product

Baltimore Aircoil

DCV-AD - D3

Water Saving Products

.

... because temperature matters

DCV-AD - D4

Benefits

DCV-AD

.

High Thermal Performance z

z

The TrilliumSeries Condenser is a V-type dry condenser equipped with unique adiabatic air precooling sections, which greatly enhance the condenser’s capacity, reducing condenser’s size and allowing gaz temperatures to be cooled far below ambient temperature. Only when necessary (at high ambient temperatures), the adiabatic pre-cooling will be activated. The adiabatic pre-cooling sections consist of a full stainless steel frame, with water distribution outside the airflow, and highly efficient evaporative cooling medium. During adiabatic operation, the evaporative medium is wetted with water, which is evenly distributed over the top of the medium at city water pressure. As the air passes through the pads, water is evaporated in the air, and the air is humidified and cooled down to temperatures at 2 to 3 °C above wet bulb temperature.

Principle of Operation TrilliumSeries Condenser

SST Frame with Adiabatic Pre-Cooling Pads

1 . Dry Heat Exchanger Coil; 2. Refrigerant inlet; 3. Refrigerant outlet; 4. Axial Fans; 5. High Efficient Evaporative Cooling Pad; 6. Water inlet Connections; 7. Water outlet Connections; 8. Adiabatic Cooling of Ambient Air; 9. Air Discharge; 10. Air in.

Baltimore Aircoil

DCV-AD - D5

Water Saving z

Operational Safety z

z

z

z

Water Consumption

While part of the water distributed over the 1. Evaporative Cooling; 2. Hybrid Cooling; 3. TrilliumSeries adiabatic pre-cooling medium evaporates to cool the air, excess water assists in rinsing the pads to keep it free from debris and minerals that would stay behind on the pad after evaporation. The pre-cooling system of the TrilliumSeries Condenser is designed as once-through system. The excess water leaves the adiabatic section via a gutter system to the sewer, avoiding stagnant water conditions and avoiding water re-circulation, both conditions that would increase the risk for micro-biological contamination and proliferation. After each adiabatic pre-cooling cycle, the adiabatic controls will open drain valves guaranteeing full emptying and drying of all pre-cooling water distribution piping installed on the condenser. The special pre-cooling medium design guarantees that neither droplets, nor aerosols are being generated while pre-cooling is activated. Water carry-over from the pre-cooling section to the dry coil is avoided.

Limited Maintenance z

Unlike dry condensers equipped with spray systems, the TrilliumSeries Condenser provides stable and predictable thermal performance without the need for high pressure pumps and water treatment.

Installation of Pre-Cooler Medium

Installation of Pre-Cooler Medium

... because temperature matters

Water Saving Products

The TrilliumSeries Condenser is delivered with intelligent adiabatic controls limiting water consumption to very short periods of time, activating adiabatic pre-cooling at both sides simultaneously and only when necessary. When compared to a traditional evaporative cooling installation, without built-in hybrid technology and controls, the TrilliumSeries Condenser saves more than 85% of the water.

DCV-AD - D6

DCV-AD

z

The pre-cooling medium can be removed during colder seasons. If kept in place however, the adiabatic pre-cooling could be used to enhance energy saving operation and it acts as filter, protecting the dry coil year-round from any air borne debris which could cause coil contamination.

Installation of Water Distribution Pad

Baltimore Aircoil

Installation of Top Bar

DCV-AD - D7

Construction Details

1. Heavy Duty Construction

z Fan designed for frequent starting, up to 60 times an hour.

z Structure and casing of bolted heavy gauge hot dipped galvanised

z Continuous running at –40°C to 60°C air temperature.

steel panels Z275 with double break angles and intermediate coil supports. Casing painted with zinc aluminium coating. z Full baffles separate individual fan sections.

z The bearing seals and encapsulation of the motor eliminate the possibility of contamination, hence extending the product life. z The fan and motor are designed to be totally maintenance free.

2. Heat Exchanger (Not Shown)

4. Adiabatic Pre-cooler

z Staggered or parallel tube arrangement with dense tube spacing. z Rigid 0,17 mm or 0,14 mm thick aluminium fins with rippled, corrugated fin surface design with 2,12 mm or 2,54 mm fin spacing, creates turbulent air stream for high performance. z High quality seamless 15,9 mm or 12,7 mm diameter copper/ stainless steel 304L tubes, with 0,4 mm and 0,7 mm wall thickness. z Thick stainless steel type 316L or seamless copper headers and threaded connections. z Coil according to European Pressure Equipment Directive 97/23/EC. z Pneumatically tested at 30 bar standard coil.

3. Fan & Fan Motor

z Casing in bolted heavy gauge stainless steel. z Water distribution outside the airflow. z Water collecting sump, draining water, once through to sewage. z Highly efficient impregnated cellulose paper evaporative cooling pad.

5. Electrical Panel and Adiabatic Controls z Factory installed electrical panel of IP55 enclosure, including main

isolating power switch with lock provision, main fuses, emergency cut-out switch, thermal contactor with coil for each fan wired to the fan motor thermostatic cut-out switch, a control switch and 400/230 transformer. z TrilliumSeries Condensers with factory installed electrical panel with Variable Frequency Drive are delivered with integrated adiabatic controls.

z Low profile fan. z Asymmetrically spaced and crenulated blades give low noise characteristics and increased efficiency.

... because temperature matters

Water Saving Products

TrilliumSeries Condenser

DCV-AD - D8

Custom Features and Options Casing Construction

DCV-AD

Structure and casing are constructed of bolted heavy gauge hot dipped galvanised steel panels Z275 (275 gr. of zinc per m2) with double break angles and intermediate coil supports. Panels are bolted with the best hardware available on the market, triple protected against corrosion, with zinc phosphate treatment, zinc rich inorganic resin coating and aluminium rich organic topcoat. As standard the outside of the casing is painted with Baltiplus zinc aluminium polymeric coating.

Heat Exchanger Construction Materials Each coil is manufactured according to the European Pressure Equipment Directive (PED) 97/23/EC. BAC condenser coils are standard available at a design pressure of 21 bar. Design temperatures are minimum -20°C and maximum +120°C. z

z

The standard materials of construction for the heat exchanger are stainless steel type 304L or seamless copper tubes with 0,7mm/0,4 mm wall thickness and corrugated aluminium fins of 0,17 mm/0,14 mm thickness and 2,12 mm/2,54mm fin spacing.

Heat Exchanger

For aggressive environments in industrial applications or installation at coastal areas, aluminium fins with pre-coated hydrophobic anti-corrosion surface treatment are available. Both sides of the aluminium fin are coated with a layer of epoxy phenolic resin. After thermosetting the high quality and firmly bonded hydrophobic film is highly effective in minimising salt corrosion and has excellent solvent resistance.

Baltimore Aircoil

DCV-AD - D9

Accessories Safety Switch If required by local codes a safety switch for each fan can be installed next to the respective fan and it is fully wired.

Control Panel

Control Panel with Variable Frequency Drive and Integrated Adiabatic Controls

... because temperature matters

Water Saving Products

Basic delivery of TrilliumSeries condensers is complete with factory installed control panel of IP55 enclosure, including, main isolating power switch with lock provision, main fuses, emergency cut-out switch, thermal contactor with coil for each fan wired to the fan motor thermostatic cut-out switch, 400/230 transformer, control circuit switch, Variable Frequency Drive and integrated adiabatic controls. In this execution, the 2 adiabatic pre-cooling sides are controlled simultaneously in function of a logical combination of ambient temperature and condensing temperature. The adiabatic control sequence guarantees maximum water savings and the adiabatic set point is adjustable.

DCV-AD - D10

Engineering Data

DCV-AD

REMARK: Do not use for construction. Refer to factory certified dimensions & weights. This brochure includes data current at time of publication, which should be reconfirmed at the time of purchase. In the interest of product improvement, specifications, weights and dimensions are subject to change without notice. Up-to-date engineering data and more can be found at www.BaltimoreAircoil.com.

1. Refrigerant inlet connections; 2. Refrigerant outlet connections; 3. Pre-cooler water drain and overflow; 4. Electrical panel; 5. Pre-cooler city water connection.

Standard Sound Level Models – Fans Ø 900 mm – 6 pole motor – Refrigerant NH3 Model DCV-AD

Refrigerant

Number of Fans

Air Flow m3/s Δ/Y

Surface m2

Tube Internal Volume dm3

LpA dB(A) Δ/Y

Ship. Weight kg

Dimensions mm L

W

H

S9022-S416B-AD

NH3

4 oo oo

24/18

1850

191

59/52

1557

2546

2904

2635

S9023-S416B-AD

NH3

6 ooo ooo

36/27

2775

287

61/54

2190

3646

2904

2635

S9024-S416B-AD

NH3

8 oooo oooo

48/35,9

3700

382

61/54

2871

4746

2904

2635

S9025-S416B-AD

NH3

10 ooooo ooooo

60/44,9

4625

478

62/55

3564

5878

2904

2635

S9026-S416B-AD

NH3

12 oooooo oooooo

72/53,9

5550

574

63/56

4218

6918

2904

2635

Baltimore Aircoil

DCV-AD - D11

Standard Sound Level Models – Fans Ø 900 mm – 6 pole motor - Halocarbon Refrigerants Model DCV-AD

Refrigerant

Number of Fans

Air Flow m3/s

Surface m2

Δ/Y

Tube Internal Volume dm3

LpA dB(A)

Dimensions mm

Ship. Weight kg

Δ/Y

L

W

H

Halocarbon

4 oo oo

23,6/18,5

1487

182

59/52

1359

2546

2904

2635

S9023-S613A-AD

Halocarbon

6 ooo ooo

35,4/27,7

2231

273

61/54

1910

3646

2904

2635

S9024-S613A-AD

Halocarbon

8 oooo oooo

47,2/37

2975

364

61/54

2530

4746

2904

2635

S9025-S613A-AD

Halocarbon

10 ooooo ooooo

59/46,2

3718

455

62/55

3119

5878

2904

2635

S9026-S613A-AD

Halocarbon

12 oooooo oooooo

70,8/55,4

4462

546

63/56

3685

6918

2904

2635

1. Sound Pressure Levels (LpA) are measured in the horizontal plane at a distance of 10 m from the connection end of the unit, under free field conditions.

2. Adiabatic pre-cooling sections are shipped separately and need to be installed on site.

Sound Power Levels for one fan at nominal speed rating DCV-AD Product Range

Standard Sound Level

Fan Motor

50Hz

Outlet Sound Power Level at Octave Band Center Frequency (Hz)

Total

Conn.

63

125

250

500

1000

2000

4000

8000

LwA

6-pole

Delta

62

76

82

85

85

83

80

74

89

6-pole

Star

55

69

75

78

78

76

73

67

82

Sound Pressure Correction Values LpA for Other Distances For other distances the change in sound pressure depends on the dimensions of the equipment. Therefore, the correction values given in the table below are approximate values. m

2

3

5

10

15

20

30

40

50

dB(A)

+14

+10

+6

0

-4

-6

-9

-12

-14

... because temperature matters

Water Saving Products

S9022-S613A-AD

DCV-AD - D12

Engineering Specifications TrilliumSeries Condensers

DCV-AD

1.0 Heat Exchanger 1.1 General: The finned Coil Heat Exchanger consists of either 15,9 mm or 12,7 mm O.D. phosphorus deoxidised stainless steel type 304L or copper seamless tubes and aluminium fins. Parallel or staggered tube construction provides substantially higher capacity since more tubes are exposed to the air stream. The advanced rippled-corrugated fin design creates a state of continuous turbulence, which effectively reduces the boundary layer formation that could otherwise reduce the rate of heat exchange. Fins have full drawn collars to maintain fin spacing and provide a continuous surface cover over the entire tube. The tubes are mechanically

expanded into the fin collars to provide a continuous primary to secondary compression bond over the entire finned length for maximum heat transfer rates. The coils are circuited for counterflow heat transfer to provide the maximum mean-effective temperature difference. The refrigerant condensing coil shall be according to the European Pressure Equipment directive (PED) 97/23/EC. The refrigerant condensing coil shall be tested at 30 bar air pressure under water.

2.0 Air Movement 2.1 The air movement package: This air movement package combines premium aerodynamic and acoustic performance with innovative design to offer a compact fan and motor as an integrated product. 1. Adjustable pitch angle impeller allows the optimum aerodynamic performance to be achieved for the given motor output, therefore minimising running costs. 2. Exceptionally compact design with short overall motor length. 3. Two speed by delta / star reconnection speed control. 4. Minimal moving parts for maximum reliability. 5. Motor protection IP55.

2.4 Motor: Suitable for horizontal through to vertical shaft operation. IP55 protection, with removable drain plugs. Bearings lubricated with wide temperature range grease, re-lubricated or sealed for life depending on size. Insulation class F as standard. The motor is designed to give maximum flexibility of control by PWM Frequency Inverter, or Voltage Speed Control and where appropriate can be used to give two speeds by Delta/Star reconnect, where 80% of the full speed can be obtained by this method. Electrical Supply 380 -420 V / 50 Hz / 3 ph 440- 480 V / 60 Hz / 3 ph Motor Electrical Details The motor can be run continuously from -40ºC to +60ºC.

6. Insulation Class F.

Motor Poles

7. Fan designed for frequent starting.

Motor Rating, kW

8. Continuous running from -40ºC to 60ºC. 9. Integral Overheat thermal cut-out protection.

Speed, Rpm

2.2 Fan(s): The Fan has superb performance with a steep volume/ pressure performance curve, giving greater flexibility in design and making it more “tolerant” of pressure variations which may occur because of, for instance, dirt accumulation on the fins of the heat exchanger. The fan, being an integrated product of impeller and motor, is balanced as a complete unit using dynamic single plane balancing. Balance grade is G6.3. The fan and motor are designed to be totally maintenance free. 2.3 Impeller: The impeller has an aluminium hub and clamp-plate, with six equally spaced, fully adjustable, moulded, black, ultra-violet resistant, glass coupled polypropylene airfoil section blades, designed on the latest aerospace technology. All rotating aluminium components are X-ray examined prior to machining to ensure quality.

Full Load Current, A

Starting Current, A

6 Poles Δ

2,1

Y

1,1

Δ

925

Y

725

Δ

5,74

Y

3,8

Δ

24,0

Y

18,4

Performance Data The air and sound performance data has been measured in accordance with the following Standards: ISO 5801:1977, type A installation test method for air performance (dual numbered BS 848 Part1: 1997) BS 848 Part 2:1985, type A installation, method of noise testing.

3.0 Supporting Frame and Casing 3.1 Frame and Casing: The supporting Frame and Casing is an allbolted painted galvanised steel construction designed to withstand

the most adverse weather conditions. Double brake flanges maximise strength of panels. Full baffles separate individual fan sections.

Baltimore Aircoil

DCV-AD - D13

4.0 Adiabatic Pre-Cooler through the pad evaporates most of the water. Any remaining water assists in washing the pad, and is drained to the gutter. In addition scaling is kept to a minimum and no water carry-over occurs due to the fact that the water is directed to the air inlet side of the pad and this where the evaporation takes place. The air that leaves the pad is therefore cooled and humidified simultaneously without any external energy supply, and without formation of aerosols. For proper Legionella bacteria control, the system and all its water distribution piping is completely drained and dried after each adiabatic cycle. 4.2 Adiabatic Pre-Cooling Casing: The adiabatic pre-cooling casing is made of stainless steel, designed as a direct water system, without the need for pumps.

5.0 Electrical Panel and Controls 5.1 TrilliumSeries Condenser delivered with factory installed electrical panel with variable frequency drive: For TrilliumSeries Condenser delivered with factory installed electrical panel including variable frequency drive, the TrilliumSeries Condenser will be delivered with panel of IP55 enclosure, including main isolating power switch with lock provision, main fuses, emergency cut-out switch, thermal contactor with coil for each fan wired to the fan motor thermostatic cut-out switch, 400/230 transformer, control circuit switch. Danfoss Variable Frequency Drive with built-in RFI filters protected to 1st environment and EN55011 to 1B, built-in DC Link coils which

reduce harmonic distortion. Hand-Off-Auto function - fast and easy commissioning. Local control Panel - clear text display read-out. Inverter by-pass power switch. Digital controller and ambient temperature sensor. Both fan speed signal from variable speed drive and ambient temperature signal are fed to the digital controller. The adiabatic precooling will be activated and stopped on the basis of a preprogrammed logical combination of the two signals in the digital controller.

... because temperature matters

Water Saving Products

4.1 Adiabatic Pre-Cooling Medium: The MUNTERS EPACC™ adiabatic pre-cooling section serves as an adiabatic saturator to cool the incoming air. It consists of specially impregnated and corrugated cellulose paper sheets with different flute angles, one steep and one shallower that have been bonded together. Such a design yields a cooling pad with high evaporation efficiency while still operating with a very low-pressure drop. The impregnation procedure for the cellulose paper ensures a strong self supporting product, with high absorbency, which is protected against decomposition and rotting. The evaporative fluid, such as city water, is supplied to a distribution manifold and the rate of the water flow may be initially regulated by a manual-regulating valve. A distribution pad on the top of the cooling pad ensures an even water distribution and minimises the risk of dry spots. The water flows down the corrugated surface of the evaporative cooling pad. The incoming warm and dry air that passes

HXC - D 1

HXC

Hybrid Condenser

Water Saving Products

Product Detail HXC Hybrid Condenser ........................................................................... D2 Benefits ....................................................................................................... D4 Construction Details .................................................................................. D6 Custom Features and Options .................................................................. D8 Accessories ............................................................................................... D11 Engineering Data ..................................................................................... D13 Structural Support .................................................................................. D18 Engineering Specifications ..................................................................... D19

HXC - D 2

HXC Hybrid Condenser Capacity Single Cell Capacity:

HXC

710- 2460 Nominal R-717 kW

General Description The HXC Hybrid Condenser offers significant water savings versus traditional water-cooled and evaporative condensers. Thanks to the standard design features the HXC satisfies additional environmental concerns by minimising also energy consumption, refrigerant charge and plume. The HXC minimises operating cost, provides year-round operating reliability and simplifies maintenance requirements.

Key Features z

Maximum water savings

z

Low energy consumption

z

Low refrigerant charge

z

Low installed cost

z

Easy maintenance

z

Plume abatement

z

Reliable year-round operation

z

Long service life

z

PED 97/23/EC Coil Design

Baltimore Aircoil

HXC - D 3

Principle of Operation

1. Air in; 2. Air out; 3. Vapour in; 4. Liquid out; 5. Wet deck surface; 6. Cold water basin; 7. Water distribution system; 8. Coil; 9. Spray Water Pump; 10. Eliminators; 12. Dry finned coil; 13. Modulating air inlet dampers; 14. Servo motor; 15. Pressure transmitter.

... because temperature matters

Water Saving Products

The refrigerant enters the dry (finned) coil at the top, which is to be connected with the wet (prime surface) coil in series. Liquid refrigerant leaves at the bottom outlet of the wet coil. When the dampers are closed, air is induced through the wet sections (coil and fill), where it picks up heat and humidity. The air is then led over the dry (finned) coil, where it picks up additional sensible heat. Due to the sensible heat transfer of the dry (finned) coil, water consumption is reduced, when compared to a conventional evaporative condenser. To save compressor energy and reduce the condensing heat (and water consumption) the HXC hybrid condenser will operate with dampers closed until a given value of condensing temperature is reached and the ambient air is cold enough to contribute to the heat rejection. When the dampers open the air flow increases due to the lower resistance to air flow and the air distribution will shift, so that less air is induced through the evaporative sections, both of which enhances the sensible heat transfer and further reduces water consumption. If the ambient air temperature is low enough to allow dry operation, the spray pump is shut off and no water is consumed at all.

HXC - D 4

Benefits Maximum Water Savings Water savings are achieved throughout the year with different operating modes of the HXC. In some areas, the water cost savings alone can pay for the equipment in as little as two years!

HXC

z

z

z

z

During the “dry/wet” operating mode, a significant amount of heat is removed by sensible heat transfer, providing reduced water consumption versus conventional evaporative cooling When the heat load and/or ambient temperatures drop, the condensing pressure is lowered to a set value, hence saving energy and water When temperature of the ambient air is low enough, dampers in the back of the condenser open, hereby introducing an increased flow of colder ambient air, which enhances the heat transfer on the dry coil and further reduces water consumption Water consumption is totally eliminated in the “dry” operating mode

Low Energy Consumption The HXC provides heat rejection at the lowest possible energy input and maintenance requirements via: z

z

High efficiency, low kW axial fans Patented combined flow technology, which reduces evaporation directly off the coil, minimizing the potential for scaling and fouling

z

Parallel flow of air and spray water, which eliminates scale-promoting dry spots

z

Variable frequency drive or two speed motors

Reduced Refrigerant Charge z

z

Combined flow technology provides maximum capacity at the lowest refrigerant charge available in the industry. Reduced refrigerant charge lowers installation costs and may help satisfy refrigerant charge thresholds.

Note: For more information on combined flow technology, refer to section Evaporative Condenser Product Line Overview.

Low Installed Cost Support — All models mount directly on parallel I-beams and ship complete with motors and drives factory-installed and aligned.

1. HXC, 2. Forced Draft; 3. Induced Draft

Modular Design — Units ship in three pieces to minimize the size and weight of the heaviest lift, allowing for the use of smaller, less costly cranes. Coil Connections — Single prime surface coil reduces costs of pipe, valves, purgers and labour.

Baltimore Aircoil

HXC - D 5

Easy Maintenance z

z

z

Access — Hinged access doors and a standard internal walkway provide easy access to the unit interior. Spacious Interior — Provides easy access to the cold water basin, drift eliminators, fan drive system, the prime surface coil and the modulation fan dampers.

Large Access Door

Removable Drift Eliminators

Plume Abatement The HXC offers a combination of sensible, adiabatic, and evaporative heat transfer to significantly reduce any plume that may occur with conventional evaporative cooling equipment. During the coldest times of the year, when the potential for visible discharge is greatest, the HXC operates 100% dry, completely eliminating plume.

Reliable Year Round Operation z

z

Belt Drive System utilizes special corrosion-resistant materials of construction and state-ofthe-art technology to ensure ease of maintenance and reliable year-round performance. Combined Inlet Shields prevent biological growth from sunlight, act as a filter for air borne impurities and debris and eliminate water splash out.

Long Service Life z

Materials of Construction – Various materials are available to meet the corrosion resistance, unit operating life, and budgetary requirements of any project.

Note: For more information, please refer to the section “Technical Resources, Materials of Construction”.

... because temperature matters

Water Saving Products

Access to spray Distribution – Parallel flow of air and spray water over the coil allows for inspection and access to the top of the coil during full operation.

HXC - D 6

HXC

Construction Details

Baltimore Aircoil

HXC - D 7

1. Heavy-Duty Construction z

z

Z600 hot-dip galvanized steel panels

Designed and manufactured by BAC

8. Combined Inlet Shield Technology

2. Fan Drive System (Not Shown)

z

Corrosion Resistant

Premium quality belts

z

Easily removable

z

Corrosion resistant sheaves

z

UV resistant plastic material

z

Heavy-duty bearings

9. Cold Water Basin

z

Adapted fan motor for operation in saturated conditions.

z

Sloped cold water basin for easy cleaning

z

Suction strainer with anti-vortex hood

z

Adjustable water make-up assembly from air inlet side Integral internal walkway as standard

3. Low kW Axial Fan(s) (Not Shown) z

Quiet operation

z

High Efficiency

z

z

Corrosion resistant aluminum

10. Hinged Access Doors z

4. Water Distribution System z

Visible and accessible during operation

z

Overlapping spray patterns ensure proper water coverage

z

Large orifice, non-clog nozzles

Inward swinging door

11. Recirculating Spray Pump z

Close coupled, bronze fitted centrifugal pump

z

Totally enclosed fan cooled (TEFC) motor

z

Bleed line with metering valve installed from pump discharge to overflow

5. Prime Surface Coil (Not Shown) z

Continuous serpentine, steel tubing

12. Modulating Air Inlet Dampers

z

Hot-dip galvanized after fabrication (HDGAF)

z

Galvanised Steel

z

Sloped tubes for free drainage of fluid

z

Opposed blade, air-tight design

z

Designed for maximum 23 bar operating pressure according to PED

z

Located in the back of the upper "wet" section

13. Actuators (Not shown) 6. Dry Finned Coil z

z

Stainless Steel tubing with high density aluminum fins

Two actuators for modulation of the dampers

14. Controller (Not Shown)

z

Designed for max. 23 bar operating pressure according to PED

z

Programmable controller with multiple set points for maximum operating savings.

z

Staggered tubes coil arrangement

z

For sequencing the operation of dampers, fans and spray pump

7. BACross® Wet Deck Surface with Integral Drift Eliminators (Not Shown) z

Plastic material

z

Impervious to rot, decay and biological attack

15. Pressure Transmitter (Not Shown) z

To be installed on site (in the condenser discharge piping)

... because temperature matters

Water Saving Products

z

HXC - D 8

Custom Features and Options Construction Options

HXC

z

z

z

Standard Construction: Steel panels and structural elements are constructed of Z600 heavy-gauge hot-dip galvanized steel protected with the Baltiplus Corrosion Protection on the outside of the unit. Optional BALTIBOND® Corrosion Protection System: The BALTIBOND® Corrosion Protection System, a hybrid polymer coating used to extend equipment life, is applied to all hot-dip galvanized steel components of the unit. Optional Stainless Steel Construction: Steel panels and structural elements are constructed of stainless steel either type 304 or 316.

Note: Refer to section Technical Resources, Material Options for more details on the materials described above.

Prime Surface Coil Configurations Each coil is manufactured according to the European Pressure Equipment Directive (PED) 97/23/EC (For more details, refer to the Evaporative Condenser "Overview" section) BAC condenser coils are standard available at a design pressure of 23 bar, and are pneumatically tested at 34 bar. z

z

Standard Serpentine Coil: The standard condensing coil is constructed of continuous lengths of all prime surface steel, hot-dip galvanized after fabrication (HDGAF)

Hot Dip Galvanised Coil

Optional Stainless Steel Coil: Coils are available in Type 304L and 316L stainless steel for specialized applications.

All coils are designed for low pressure drop with sloping tubes for free drainage of fluid.

Dry Finned Configuration The standard dry finned coil on the HXC hybrid condenser consists of a 6-row stainless steel AISI 304L coil in a staggered "triangle" arrangement with precoated aluminium high density fins. The coil is designed in accordance to PED regulations and has an operating pressure of 23 bar.

Stainless Steel Finned Coil

Baltimore Aircoil

HXC - D 9

Wet Deck Surface z

z

z

Fill pack extended into the cold water basin to avoid sound of water splash Reduction of recirculating spray water temperature results in compact prime surface coil which reduces both refrigerant and piping costs. Saturation and pre-cooling of incoming outside air

Wet Deck Surface

Modulating Air Inlet Dampers z

Dampers are located in the back of the upper "wet section".

z

Constructed of galvanised steel

z

Opposed blade, air-tight design

z

Proportional modulation through beams

Air Flow Control Package An air flow control package is included to provide maximum water savings and plume control. This Modulating Air Inlet Dampers package consists of a pressure transmitter (shipped loose for site installation in condenser discharge piping), actuators to activate the modulating air inlet dampers and a control system to intelligently modulate the dampers when needed. The condensing pressure is allowed to float down to a set minimum value in parallel with a proportional regulation of the cold air entry to minimise water consumption.

Fan Drive System The low sound fan drive system provides the cooling air necessary to reject heat from the system to the atmosphere. The standard fan drive system consists of two sheaves located on minimum shaft centreline distances to maximise belt life. A fan motor, custom engineered for BAC to provide maximum performance for cooling tower service, is provided.

Fan Drive System

... because temperature matters

Water Saving Products

z

Cross flow plastic wet deck surface with integrated high efficiency drift eliminators

HXC - D 10

Low Noise Fans

HXC

The low sound levels generated by HXC Hybrid Condensers are thanks to the use of high efficiency low noise axial fans making them suitable for installation in most environments. For extremely sound sensitive installations, factory designed, tested and rated sound attenuation is available for both the air intake and discharge. Note: For more information, please refer to the section “Technical Resources, Sound Reduction Options”.

Low Noise Fans (dry coil section removed)

Combined Inlet Shields Combined Inlet shields prevent biological growth from sunlight, act as a filter for air borne impurities and debris and eliminate water splash out.

Remote Sump Execution The use of an auxiliary sump within a heated space is the most satisfactory way to protect sump water from freezing. When the circulating pump is shut off, all the water in the water distribution, in suspension and in the sump will drain freely to the auxiliary sump. Combined Inlet Shields Note: For detailed information on the calculation of the remote sump tank, please refer to the section "Technical Resources, Selection of Remote Sump Tank".

Removable Bundled Fill For installations where it is necessary or recommended to remove the wet deck surface for more thorough cleaning and disinfection, removable bundled fill is available. The fill bundles can be easily lifted and handled by one person and therefore provide a simple and secure method of removing and installing. The bundles can be dismantled and sheet by sheet can be removed for inspection and cleaning of both sides. After cleaning the sheets can be rebundled and re-installed.

Easy Removable Fill Bundles

Baltimore Aircoil

HXC - D 11

Accessories External Service Platform For external service, platforms can be added to the unit.

Ladder and Safety Cage In the event the owner requires easy access to the top of the unit, the unit can be furnished with a platform and ladders extending from the base of the unit to the platform, as well as safety cages.

External Service Platform

Internal Ladder For access to the motor and drive assemblies internal ladders are available on all models.

Internal Service Platforms For access to the motor and drive assemblies on models HXC 214 to 468 an upper service platform with ladder and handrails is available. Safety gates are available for handrail openings.

Top Air Inlet Screens The screens protect the air inlet side above the coil section only. Top air inlet screens are always in Baltibond Corrosion® Protection System.

Vibration Cut-out Switch A factory-mounted vibration cut-out switch is available to effectively protect against equipment failure due to excessive vibration of the mechanical equipment system. BAC can provide a vibration cut-out switch in an IP65 enclosure to ensure reliable protection.

Extended Lubrication Lines Extended lubrication lines with grease fittings are available for lubrication of the fan shaft bearings.

Extended Lubrication Lines

... because temperature matters

Water Saving Products

Internal Service Platform and Ladder

HXC - D 12

Basin Heaters

HXC

Although most units will operate dry in the winter, basin heaters are available for freeze protection when required. Basin heaters prevent freezing of the water in the cold water basin when the unit is idle. Factory-installed heaters, which maintain the water temperature at 4°C, are a simple and inexpensive way of providing such protection. Model No. HXC

Electric Immersion Heaters -18°C kW

HXC 131-147

1x6

HXC 173-193

1x6

HXC 214-288

1x8

HXC 379-424

2x6

HXC 309

2x6

HXC 468

2x6

Electric Water Level Control Package The electric water level control replaces the standard mechanical make-up valve when a more precise water level control is required. This package consists of a float switch mounted in the basin and a solenoid activated valve in the make-up water line. The valve is slow closing to minimize water hammer.

Stand-by Pump A factory mounted stand-by pump is available, including non-return valves in each pump piping line. In case of a pump failure, there can be switched over to the stand-by pump, eliminating the unit shut down period as much as possible.

N2 Filling of the Coil For prolonged shipment periods (ocean freight) or extended storage on site it is recommended to charge the coil(s) with nitrogen.

Basin Sweeper Piping Basin sweeper piping provides an effective method of preventing sediment from collecting in the cold water basin of the unit. A complete piping system, including nozzles, is provided in the unit basin for connection to side stream filtration equipment. Note: For more information, please refer to the section "Technical Resources, Filtration".

Basin Sweeper Piping

Baltimore Aircoil

N2 Filling of the Coil

HXC - D 13

Engineering Data REMARK: Do not use for construction. Refer to factory certified dimensions & weights. This brochure includes data current at time of publication, which should be reconfirmed at the time of purchase. In the interest of product improvement, specifications, weights and dimensions are subject to change without notice. Up-to-date engineering data and more can be found at www.BaltimoreAircoil.com.

HXC 131-193

Water Saving Products

1. Refrigerant in; 2. Refrigerant out; 3. Make Up ND15; 4. Overflow ND80; Drain ND50; 6. Acces door.

Fan Motor (kW)

Spray Water Flow (l/s)

Pump (kW)

Inlet/Outlet Coil Connections (mm)

Operating Shipping Heaviest Model No H Weight Weight Section HXC (mm) (kg) (kg) (kg)

L (mm)

HXC 131 HXC 147

5772 6032

4172 4402

2160 2390

5397 5397

2775 2775

2385 2385

19,6 19,1

(2x) 5,5 (2x) 5,5

18,3 18,3

(1x) 2,2 (1x) 2,2

100 100

HXC 173 HXC 193

7298 7638

5155 5455

2620 2920

5397 5397

3690 3690

2385 2385

26,1 25,5

(2x) 7,5 (2x) 7,5

31,5 31,5

(1x) 2,2 (1x) 2,2

100 100

W (mm)

Airflow (m3/s)

Prime Finned Surface Coil Coil

... because temperature matters

R717 Charge (kg) Prime Surface Coil

Dry Coil

80 80

46 57

10 10

80 80

61 76

14 14

HXC - D 14

HXC

HXC 214-468

1. Refrigerant in; 2. Refrigerant out; 3. Make Up ND25; 4. Overflow ND80; 5. Drain ND50; 6. Access door.

Fan Motor (kW)

Spray Water Flow (l/s)

Pump (kW)

Model No Operating Shipping Heaviest Weight Weight Section HXC (kg) (kg) (kg)

H (mm)

HXC 214 HXC 258 HXC 288

8625 8042 8542

6200 5547 5987

2840 3280 3720

6717 6717 6717

3690 3690 3690

2985 2985 2985

35,1 34,7 33,7

(2x) 11 (2x) 11 (2x) 11

45,1 45,1 45,1

HXC 379 HXC 424

13355 14125

9601 10271

4740 5410

6856 6856

5520 5520

2985 2985

52,9 51,4

(3x) 11 (3x) 11

HXC 309

11017

7796

4010

6856

3690

3610

36,4

HXC 468

16200

11341

5850

6996

5520

3610

56,5

L (mm)

W (mm)

Airflow (m3/s)

Inlet/Outlet Coil Connections (mm)

R717 Charge (kg)

Prime Surface Coil

Finned Coil

Prime Surface Coil

Dry Coil

(1x) 4 (1x) 4 (1x) 4

100 100 100

80 80 80

69 91 114

16 16 16

56,8 56,8

(1x) 5,5 (1x) 5,5

100 100

80 80

136 170

24 24

(2x) 9

45,1

(1x) 4

100

80

123

19

(3x) 11

56,8

(1x) 5,5

100

80

182

29

General Notes 1. Dimensional drawings show standard (right hand) arrangements. Left hand arrangement can be furnished by special order. 2. Coil connection locations are approximate. Dimensions should not be used for prefabrication of the connecting piping. All coil connections are beveled for welding. 3. Shipping/operating weights indicated are for units without accessories such as sound attenuators, discharge hoods, etc.

Consult factory certified prints to obtain weight additions and the heaviest section to be lifted. Operating weight shown in tables is based on total unit weight of refrigerant operating charge and basin filled to overflow level. 4. The units will be delivered in 3 different pieces, upper, middle and lower section.

Baltimore Aircoil

HXC - D 15

Sound Attenuation REMARK: Do not use for construction. Refer to factory certified dimensions & weights. This brochure includes data current at time of publication, which should be reconfirmed at the time of purchase. In the interest of product improvement, specifications, weights and dimensions are subject to change without notice. Up-to-date engineering data and more can be found at www.BaltimoreAircoil.com.

Water Saving Products

1. Unit Width; 2. Unit Height; 3. Insulated Plenum; 4. Intake Attenuator.

Model No. HXC

Weight Sound Attenuator (kg)

HXC 131-147

130

HXC 173-193

175

HXC 214-288

150

HXC 379-424

375

HXC 309

250

HXC 468

375

Modes of Operation Operation Mode

Modulating Air Inlet Dampers

Spray Pump

Fans

Dry-Wet Mode

Closed

ON

ON

Modulating Mode

0 – 100% Open

ON

ON

Dry Mode

100 % Open

OFF

ON*

Note: *During dry mode air flow modulation can be controlled by two-speed motor or Variable Frequency Drive.

... because temperature matters

HXC - D 16

HXC

Dry/Wet Mode The refrigerant to be condensed always first flows through the dry finned coil and then to the wet prime surface coil, where the condensed exits the unit. Spray is drawn from the cold water basin and pumped to the water distribution system above the prime surface coil. Wetting the prime surface coil allows evaporative cooling to occur. The spray water falls from the prime surface coil over the wet deck surface, enhancing the evaporative heat transfer by sub-cooling the spray water. Air is drawn through both the prime surface coil and through the wet deck surface where it is saturated and picks up heat. The air is, however, still cold enough to achieve significant heat rejection within the finned coil, which is installed at the discharge above the fan(s). In this mode the finned coil, acts in fact as a desuperheater. Due to the sensible heat transfer of the finned coil, water consumption is reduced, when compared to a conventional evaporative condenser. In the dry-wet mode, both sensible and evaporative heat transfer are used. Compared to a conventional evaporative unit, the potential for plume is substantially reduced and significant water savings can be obtained, even at peak design conditions.

Dry-Wet Mode

Water Consumption

Modulating Mode At reduced heat load and/or reduced ambient temperatures, the dampers may open and modulate to further reduce water consumption and to control the condensing capacity. When the dampers open, they open a low resistance path for ambient air to directly reach the fan, mixing with the humid air from the wet section of the condenser. This low resistance path reduces water consumption in two ways. First, air is drawn through the open louvers, reducing the air drawn through the wet section and the related evaporation. Second, the low resistance path allows the fans to move a greater total volume of air, which passes over the dry section and improves the performance of the dry coil. This change in airflow also serves to control capacity as the heat load is shifted from the wet section to the dry section, keeping the condensing temperature from falling as the heat load or ambient temperatures fall. In addition, the potential for plume is further diminished by reducing the amount of evaporated water and increasing the heat added to the discharge air by the dry finned coil.

Modulating Mode

Baltimore Aircoil

Water Consumption

HXC - D 17

Dry Mode During the dry mode the spray water system is turned off, saving on pump energy. With the intelligent HXC Hybrid condenser the switchpoint from wet to dry operation is improved, since the total airflow in the product increases when the dampers are fully open. In this mode no water consumption occurs, and plume is completely eliminated. When the equipment operates in the dry mode for prolonged periods, draining the cold water basin is recommended, eliminating the need for freeze protection and water treatment.

Water Consumption

Remote Sump Data Refer to the "Technical Resources" section "Selection of Remote Sump" for Remote Sump Data.

... because temperature matters

Water Saving Products

Dry Mode

HXC - D 18

Structural Support REMARK: Do not use for construction. Refer to factory certified dimensions & weights. This brochure includes data current at time of publication, which should be reconfirmed at the time of purchase. In the interest of product improvement, specifications, weights and dimensions are subject to change without notice. Up-to-date engineering data and more can be found at www.BaltimoreAircoil.com.

HXC

The recommended support arrangement for units consists of parallel I-beams running the full length of the unit, spaced as shown in the following drawing. Besides providing adequate support, the steel also serves to raise the unit above any solid foundation to ensure access to the bottom of the unit. To support units in an alternate steel support arrangement, consult your BAC Balticare Representative.

Units With and Without Sound Attenuation

1. Outline of Unit, 2. Air Intake, 3. Mounting Holes diameter 22 mm, 4. Unit

Model HXC

Dimensions (mm)

Max. Deflection (mm) (4)

W

L

A

B

C

N° of 20 mm Anchorbolts

131-147

8

2385

2775

2325

-

255

4

173-193

10

2385

3690

2325

-

255

4

214-288

10

2985

3690

2925

-

255

4

379-424

12

2985

5520

2925

2440

270

8

309

10

3610

3690

3550

-

255

4

468

12

3610

5520

3550

2440

270

8

Notes : 1. Support steel and anchor bolts to be designed and furnished by others. 2. All support steel must be level at the top. 3. Beams must be selected in accordance with accepted structural practice. Maximum deflection of beam under unit see table.

rails when determining the length of the supporting steel, as vibration rail length and mounting hole locations may differ from those of the unit. 5. If point vibration isolation is used with multi-cell units, the isolators must be located under the support steel, not between the support steel and the towers.

4. If vibration isolation rails are to be used between the unit and supporting steel, be certain to allow for the length of the vibration

Baltimore Aircoil

HXC - D 19

Engineering Specifications General

B. Capacity: The hybrid condenser(s) shall be warranted by the manufacturer to have condensing capacity of _____ kW heat

rejection, operating with ____ refrigerant at ___ºC condensing temperature and ___ºC entering wet-bulb temperature. C. Warranty: The manufacturer’s standard equipment warranty shall be for a period of one year from the date of startup or eighteen months from the date of shipment, whichever ends first. D. Quality Assurance: The manufacture shall have Management System certified by an accredited registrar as complying with the requirements of ISO-9001:2000 to ensure consistent quality of products and services.

Products 1.0 Evaporative Condenser Materials and Components 1.1 Baltiplus Corrosion Resistant Construction: Unless otherwise noted in this specification, all steel panels and structural elements shall be constructed from heavy-gauge, Z600 hot-dip galvanized steel, with all sheared edges given a protective coating of zinc-rich compound and the exterior protected with the Baltiplus Corrosion Protection. (Alternate 1.1) Baltibond® Corrosion Resistant Construction: Unless otherwise noted in this specification, all steel panels and

structural members shall be protected with the BALTIBOND® Corrosion Protection System. The system shall consist of Z600 hot dip galvanised steel prepared in a four-step (clean, pre-treat, rinse and dry) process with an electrostatically sprayed, thermosetting hybrid polymer fuse-bonded to the substrate during a thermally activated curing stage monitored by a 23-step quality assurance program.

2.0 Coil Casing Assembly The hybrid condenser shall include a coil casing section consisting of a refrigerant condensing coil, a spray water distribution system, modulating air inlet dampers, air flow control package, drift eliminators, fans and drive system as indicated by the manufacturer. 2.1. The refrigerant condensing coil shall be fabricated of all prime surface steel at the manufacturer’s own facility, and hot-dip galvanized after fabrication. a. The refrigerant condensing coil shall be according to European Pressure Equipment Directive 97/23/EC, with design pressure of 23 bar. b. The refrigerant condensing coil shall be tested at 34 bar air pressure under water. c. The refrigerant condensing coil shall be designed for low pressure drop with sloping tubes for free drainage of liquid refrigerant. 2.2 Spray Water Distribution System: Water shall be distributed evenly over the coil at a minimum flow rate sufficient to ensure complete wetting of the coil at all times by large-diameter, non-clog, 360° plastic distribution nozzles spaced across the coil face area in spray branches. Nozzles shall utilize a two-stage diffusion pattern to provide overlapping, umbrella spray patterns that create multiple intersection points with adjacent nozzles. a. Nozzles and spray branches shall be observable and accessible for cleaning from the outside of the hybrid condenser during condenser operation without the removal of other components. b. Spray branches and nozzles shall be held in place by snap-in rubber grommets, allowing quick removal of individual nozzles or complete branches for cleaning or flushing. 2.3. Removable drift eliminators shall be positioned to prevent moisture from entering the air plenum and incorporate a minimum of three (3) changes in air direction. The drift eliminators shall be removable in easy to handle sections for quick access to the coil.

2.4. Fans and Drive System: Fan(s) shall be driven by V-type belts. a. Fan(s) shall be heavy-duty, axial flow low noise, with aluminium alloy blades. Air shall discharge through a fan cylinder designed for streamlined air entry and minimum fan blade tip clearance for maximum fan efficiency. b. Fan(s) and shaft(s) shall be supported by heavy-duty, self-aligning, grease-packed ball bearings with moisture-proof seals and integral slinger rings, designed for a minimum L10 life of 40,000 hours. c. Fan and motor sheaves shall be fabricated from corrosion resistant materials. d. Fan motor(s) shall be totally enclosed fan cooled (TEFC) type, suitable for ____ volt, ____ phase, ___ Hz electrical service and shall be mounted on an easily adjusted, heavy-duty motor base. e. The motor shall be furnished with double-sealed, permanently lubricated bearings and special moisture protection on windings, shafts and bearings. f. Air plenum shall provide a minimum of 1220 mm clearance under the motor base to provide comfortable working space for service personnel. 2.5. Modulating air inlet dampers: modulating air inlet damper blocks of air-tight design (to DIN 1946) shall be located in the back of the coil casing assembly. Damper blades shall be made from galvanised rolled sheet steel and will be of opposed blade design with proportional modulation through beams. 2.6. Air flow control package: The air flow control package shall consist of a pressure transmitter (shipped loose for site installation in condenser, discharge piping), actuators to activate the modulating air inlet dampers and a control system to intelligently modulate the dampers when needed to minimise water consumption.

3.0 Pan Assembly The hybrid condenser shall include a pan assembly consisting of cold water basin with pump assembly, heat transfer section for spray water cooling with integral drift eliminators, combined inlet shields and hinged access door and internal walkway. 3.1 The cold water basin shall be constructed of heavy-gauge steel panels and structural members either protected by Baltiplus or Baltibond®. Basin shall include a depressed section with drain/ cleanout connection. The basin area under the wet deck surface shall be sloped toward the depressed section to facilitate cleaning. 3.2 The cold water basin shall include a drain/clean-out connection; a steel strainer; a brass make-up valve; over flow connection; and a

water recirculation pump assembly. a. Cold water basin shall be designed so that the strainer, makeup valve and float, and pump assembly are easily accessible without removing any of the unit panels. b. Lift-out steel strainer shall be supplied with perforated openings sized smaller than the water distribution nozzle orifices and an integral anti-vortexing hood to prevent air entrainment. c. Water recirculation pump shall be a close-coupled, bronze-fitted centrifugal pump equipped with a mechanical seal, mounted on the basin and piped from the suction strainer to the water distribution system.

... because temperature matters

Water Saving Products

A. General: Furnish and install, _____ factory assembled hybrid condenser(s) of induced draft design, with single side air entry and vertical air discharge. Overall dimensions shall not exceed approximately _____ mm x _____ mm, with an overall height not exceeding approximately _____mm. Operating weight shall not exceed _____ kg. The hybrid condenser shall be Baltimore Aircoil Model ____________.

HXC

HXC - D 20 i. The pump shall be installed with adequate drains so that it may drain freely when the basin is drained. ii. The pump assembly shall include an integral metering valve and bleed line to control the bleed rate from the pump discharge to the overflow connection. iii. The pump motor shall be totally enclosed fan cooled (TEFC) type suitable for _____ volt, ____ phase, ______ Hz electrical service. d. On installations requiring a remote sump, the hybrid condenser shall be modified to accommodate the use of an independent sump and pump for recirculating water (by others). i. The recirculating water pump, steel strainer, make-up valve, and integral bleed line assemblies shall be omitted from the hybrid condenser scope of supply. ii. The hybrid condenser shall be supplied with a cold water basin outlet sized and located as indicated on the drawings for gravity drain to the remote sump. iii. The water distribution system shall have a design operating pressure of 14 kPa at the hybrid condenser spray water inlet connection. BACross®

3.3 The heat transfer section shall consist of wet deck surface with integral drift eliminators for cooling the spray water

leaving the coil to optimize the thermal performance of the hybrid condenser as well as saturate and pre-cool the incoming ambient air. a. The wet deck surface and integral drift eliminators shall be formed from plastic material. b. The wet deck surface and integral drift eliminators shall be impervious to rot, decay, fungus, and biological attack. 3.4 Combined Inlet Shields: Combined inlet shields shall be separate from the wet deck surface and removable to allow easy access for inspection of the air/water interface at the air inlet side of the equipment. Combined inlet shields shall prevent UV-light and debris from entering the unit, as well as prevent water splash out during fan cycling. They shall be constructed of maintenance free, corrosion and UV resistant material. 3.5 Hinged Access Door: A large, hinged access door shall be provided for access to the coil, drift eliminators and fan plenum section. The water make-up valve, float ball and suction strainer shall be easily accessible. 3.6. Internal walkway: The hybrid condenser shall be provided with an internal walkway at the access door to facilitate servicing of the unit.

4.0 Dry Finned Coil Assembly The hybrid condenser shall include a dry finned coil section consisting of a heavy-gauge steel panel construction (either Baltiplus or Baltibond® Corrosion Protection) and two dry finned coils. The dry finned coils consist of a 6-row stainless steel AISI 304L coil in a

staggered triangle tube arrangement with precoated aluminium high density fins. Coil is designed in accordance to PED for 23 bar operating pressure.

5.0 Sound Sound Level: To maintain the quality of the local environment, the maximum sound pressure levels (dB) measured 15 m from the hybrid

Location

63

125

250

condenser operating at full fan speed shall not exceed the sound levels detailed below.

500

Discharge Air Inlet End Back

Baltimore Aircoil

1000

2000

4000

8000

dB(A)

EC - E 1

Evaporative Condensers Overview

Product Group Detail General Information ................................................................................. E2 Principle of Operation .............................................................................. E2 Configuration ............................................................................................. E2 Fan System ................................................................................................. E3 Capacity Range .......................................................................................... E4 Typical Applications .................................................................................. E4 Product Line Overview Table .................................................................. E4 Engineering Considerations ..................................................................... E6

Evaporative Condensers

.

EC - E 2

General Information Evaporative condensers provide heat rejection for many types of systems, and the specific application will largely determine which BAC Evaporative Condenser is best suited for a project. The product line overview table in this section is intended as a general guide. Evaporative condensers are used to provide lower condensing temperatures and compressor kilowatts savings of up to 30 percent when compared with air-cooled systems.

Overview

Principle of Operation The vapor to be condensed is circulated through a condensing coil, which is continually wetted on the outside by a re-circulating water system. Air is pulled or pushed over the coil, causing a small portion of the re-circulating water to evaporate. The evaporation removes heat from the vapor in the coil, causing it to condense.

Configuration BAC manufactures three types of evaporative condensers: combined flow, counter flow, hybrid and adiabatic products.

Combined Flow Combined flow is the use of both a condensing coil and wet deck surface for heat transfer in an evaporative condenser. The addition of wet deck surface to the traditional evaporative condenser design reduces evaporation in the coil section, reducing the potential for scaling and fouling. BAC’s combined flow evaporative condensers utilize parallel flow of air and spray water over the coil, and crossflow air/water flow through the wet deck surface. In parallel flow, air and water flow over the coil in the same direction. In the wet deck section of BAC’s combined flow evaporative condensers, air and water interact in a crossflow configuration: water flows vertically down the wet deck as air flows horizontally across it.

Combined Flow: Parallel flow of air and water over the coil

Baltimore Aircoil

Combined flow: Crossflow configuration over the wet deck

EC - E 3

Counterflow In a counterflow evaporative condenser design, the flow of the air is in the opposite direction of the spray water. In BAC’s counterflow evaporative condensers, air travels vertically up through the unit while the spray water travels vertically down over the coil.

See description under separate section "Hybrid Water Saving Products”.

Counterflow Configuration

Fan System The flow of air through most factory assembled evaporative cooling equipment is provided by one or more mechanically driven fans. The fan(s) may be axial or centrifugal, each type having its own distinct advantages. Axial fan units require approximately half the fan motor kilowatt of comparably sized centrifugal fan units, offering significant life-cycle cost savings. Centrifugal fan units are capable of overcoming reasonable amounts of external static pressure (≤125 Pa), making them suitable for both indoor and outdoor installations. Centrifugal fans are also inherently quieter than axial fans, although the difference is minimal and can often be overcome through the application of optional low sound fans and/or sound attenuation on axial fan units. Fans can be applied in an induced draft or a forced draft configuration.

Centrifugal Fans

Axial Fans

Induced Draft The rotating air handling components of induced draft equipment are mounted in the top deck of the unit, minimizing the impact of fan noise on near-by neighbors and providing maximum protection from fan icing with units operating in sub-freezing conditions. The air being drawn through the unit hereby discharges over the inducing fan. The use of corrosion resistant materials ensures long life and minimizes maintenance requirements for the air handling components. Forced Draft Rotating air-handling components are located on the air inlet face at the base of forced draft equipment whereby fresh air is blown through the unit. This base fan position facilitates easy access for routine maintenance and service. Additionally, location of these components in the dry entering air stream extends component life by isolating them from the corrosive saturated discharge air.

... because temperature matters

Evaporative Condensers

Hybrid and Adiabatic Products

EC - E 4

Capacity Range All capacities shown are for a single unit; multiple units can be applied to achieve larger capacities.

Typical Applications A list of typical applications is provided in the Product Line Overview Table for your reference.

Overview

Product Line Overview Table

VXC

2

2

10 10

3

8

Principle of Operation

1

7

3

6

9

8

1

6

13

4 9

7

2

14

11

4

1

3

12

2

7 11

HXC (For more information refer to Section Hybrid Water Saving Products)

VCL

10

1

8 15

4

10 2

5

1 6

9

Configuration

Counterflow

Counterflow

Combined flow

Fan System

Centrifugal Fan, Forced Draft

Centrifugal Fan, Forced Draft

Axial Fan, Induced Draft

Capacity Range Nominal R717 kW’s

50 to 6470 kW

160 to 1290 kW

710 to 2460 kW

Typical Applications

Sound sensitive industrial refrigeration projects Installations with limited plan area Indoor Installations

Sound sensitive industrial refrigeration projects. Installations with extremely low height requirements Indoor Installations Skid packages

Industrial refrigeration applications in geographical regions where water cost is high.

For VXC, VCL, HXC, CXV, CXV-D: 1. Air in; 2. Air out; 3. Vapour in; 4. Liquid out; 5. Wet deck surface; 6. Cold water basin; 7. Water distribution system; 8. Coil; 9. Spray Water Pump; 10. Eliminators; 11. Optional Extended Surface. 12. Dry finned coil; 13. Modulating air inlet dampers; 14. Servo motor; 15. Pressure transmitter.

HXC and DCV water saving and hybrid wet-dry products are available to meet these specific design requirements. Refer to the “Water Saving Products” section for more details on these products.

Baltimore Aircoil

EC - E 5

DCV TrilliumSeries Condenser (For more information refer to Section Hybrid Water Saving Products)

CXV-D

9

1

2

2

8

10

3

4

5

8

4

5

6

9

1

2

4

10

5

1

6

4

3

7

10 2

6

2

2

3

7

10

10

6

9

8

5

2

1

8

1

1 7

3

7

Combined Flow

Combined Flow

Counterflow

Axial Fan, Induced Draft

Axial Fan, Induced Draft

Axial Fan, Induced Draft

3500 to 5140 kW

340 to 1030 kW

410 to 2730 kW

Industrial refrigeration applications

10

Very large industrial refrigeration and process projects requiring low energy consumption and low sound

Small to medium industrial refrigeration projects Locations with limited water and limited space availability

For TrilliumSeries Condenser: 1. Dry heat exchanger; 2. Fluid in; 3. Fluid out; 4. Axial Fans; 5. High efficiency evaporative coolingpad; 6. Water inlet connections; 7. Water outlet connections; 8; Adiabatic cooling ot ambient air; 9. Air Discharge; 10. Air In.

... because temperature matters

Evaporative Condensers

CXV

EC - E 6

Engineering Considerations Location

Overview

Units must have an adequate supply of fresh air to the air inlet(s). When units are located adjacent to building walls or in enclosures, care must be taken to ensure that the warm, saturated discharge air is not deflected off surrounding walls or enclosures and drawn back to the air inlet(s). Warning: Each unit should be located and positioned to prevent the introduction of the warm discharge air and the associated drift, which may contain chemical or biological contaminants including Legionella, into the ventilation systems of the building on which the unit is located or those of adjacent buildings.

Note: For detailed recommendations on layout, please consult your local BAC Balticare Representative.

For VL and VX products, bottom screens or solid bottom panels may be desirable or necessary for safety, depending on the location and conditions at the installation site.

Piping and Valves Piping should be adequately sized according to standard refrigeration practice and arranged to allow flexibility for expansion and contraction between component parts of the system. Suitably sized equalising lines must be installed between the condenser and high pressure receiver to prevent gas binding and refrigerant backup in the condenser. Service valves should be installed so that the component parts may be easily serviced. On multiple evaporative condenser installations, evaporative condensers in parallel with shell-andtube condensers, or single condensers with multiple coils, refrigerant outlet connections must be trapped into the main liquid refrigerant header. The height of the trapped liquid legs must be sufficient to balance the effect of the unequal coil pressures without backing up liquid refrigerant into the condensing coil. This type of liquid line piping permits independent operation of any one of the parallel circuits without manually closing inlet and outlet valves. Although equalising lines can be used to balance water levels between multi-cell evaporative condensers, the spray water for each cell must be treated separately, and a separate make-up must be provided for each cell. Note that a common remote sump for multi-cell installations can simplify make-up and water treatment. See section "Technical Resources, Application Guidelines" or the appropriate Operating and Maintenance Instruction Manual for more information on water treatment. Weld Byproduct Cleaning The installation and manufacturing processes commonly used for field assembly of steel-piped systems may leave weld byproducts inside coils and connecting piping (especially in refrigeration systems). It is common practice to install filters and/or strainers that remove contaminants during initial system operation. Shortly after system startup, the filters and/or strainers should be cleaned or replaced.

Capacity Control Variable Frequency Drives (VFD) Installations which are to be controlled by Variable Frequency Drives (VFD) require the use of an inverter duty motor as designed IEC 34.1, which recognizes the increased stresses placed on motors by these drive systems. Inverter duty motors must be furnished on VFD applications in order to maintain the motor warranty. Fan motors must be furnished with thermal protection (either PTC sensors or coil thermostats normally open, or normally closed). The motor protection consists of temperature sensitive cutout devices embedded in the motor windings (minimum 3 per motor).

Baltimore Aircoil

EC - E 7

The minimum fan motor speed during normal operation should be not below 30% of the speed indicated on the motor nameplate. This corresponds with 15 Hz for a 50 Hz supply and 18 Hz for a 60 Hz supply. BAC offers factory installed motor control packages including VFD drives. Refer to the section "Technical Resources, Motor Controls". Check with your local BAC Balticare representative for availability.

Fan Cycling Fan cycling is the simplest method of capacity control. The number of steps of capacity control can be increased using the Baltiguard® Fan System, the independent fan motor option, or two-speed fan motors in conjunction with fan cycling (see the “Custom Features & Options” section of the appropriate product line to determine whether the Baltiguard® Fan System or the independent fan motor option are available; two-speed motors are available for all products). These options provide substantial energy savings when compared to simple fan cycling. Warning: Rapid on-off cycling can cause the fan motor to overheat. It is recommended that controls be set to allow a maximum of 6 on-off cycles per hour.

Note: Spray water pump cycling should not be used for capacity control. This method of control often results in short cycling of the pump motor as capacity changes substantially with pump cycling. In addition, alternate wetting and drying of the coil promotes scaling of the heat exchanger coil surface.

Capacity Control Dampers On centrifugal fan models, modulating capacity control dampers are available to provide close control of head pressure. See Section "Accessories" or contact your local BAC Balticare representative.

Vibration Cut-out Switch Vibration cutout switches are recommended on all axial fan installations. Vibration cutout switches are designed to interrupt power to the fan motor and/or provide an alarm to the operator in the event of excessive vibration. BAC offers both electronic and mechanical vibration cutout switches on all evaporative condensers.

Water Treatment As water evaporates in the unit, the dissolved solids originally present in the water remain in the system. The concentration of these dissolved solids increases rapidly and can cause scale and corrosion. In addition, airborne impurities and biological contaminants, including Legionella, may be introduced into the circulating water. To control all potential contaminants, a water treatment program must be employed. In many cases, a simple bleed-off may be adequate for control of scale and corrosion. However, biological contamination, including Legionella, can be controlled only through the use of biocides. Such treatment should be initiated at system startup, after periods of equipment shutdown, and continued regularly thereafter. Accordingly, it is strongly recommended a biocide treatment be initiated when the unit is first filled with water and continued regularly thereafter. For more information, consult the appropriate Operating and Maintenance Manual. When a water treatment program is employed, it must be compatible with construction materials. Batch feeding of chemicals into the unit is not recommended. If units are constructed with optional

... because temperature matters

Evaporative Condensers

Warning: When the fan speed is to be changed from the factory-set speed, including through the use of a variable speed control device, steps must be taken to avoid operating at or near fan speeds that cause a resonance with the unit or its supporting structure. At start-up, the variable frequency drive should be cycled slowly between zero and full speed and any speeds that cause a noticeable resonance in the unit should be “locked out” by the variable speed drive.

EC - E 8

corrosion resistant materials, acid treatment may be considered; however, the water quality must be maintained within the guidelines set forth in the Operating and Maintenance Instructions. Note: Unless a common remote sump is utilised, each cell of a multi-cell installation must be treated as a separate entity, even if the cold water basins are equalized.

Overview

For complete Water Quality Guidelines, see the appropriate Operating and Maintenance Instruction Manual, available at www.baltimoreaircoil.com. For specific recommendations on water treatment, contact a competent water treatment supplier.

Sound Levels Sound rating data are available for all BAC models. When calculating the sound levels generated by a unit, the designer must take into account the effects of the geometry of the tower as well as the distance and direction from the unit to noise-sensitive areas. Whisper Quiet fans and intake and discharge sound attenuation can be supplied on certain models to provide reduced sound characteristics (see the “Custom Features and Options” section of the appropriate product line for details). The Baltiguard® Fan System, two-speed motors, or variable frequency drives can also be used to reduce sound during periods of non-peak thermal loads. For more information on sound and how it relates to evaporative cooling equipment, see Section "Technical Resources, Fundamentals of Sound". For detailed low sound selections, please consult your local BAC Balticare Representative.

Winterization When a unit is shut down in freezing weather, the basin water must be protected by draining to an indoor auxiliary remote sump tank or by providing supplementary heat to the cold water basin. Supplementary heat can be provided by electric immersion heaters or in some cases, hot water, steam coils, or steam injectors. All exposed water piping, make-up lines, and spray pumps (if applicable) that do not drain at shutdown should be traced with electric heater tape and insulated. When dry operation is planned for low ambient conditions, centrifugal fan units should be supplied with oversized fan motors to prevent motor overload when the spray water is not operating. For remote sump applications, the spray water pump must be selected for the required flow at a total head which includes the vertical lift, pipe friction (in supply and suction lines) plus the required pressure at the inlet header of the water distribution system (14 kPa). A valve should always be installed in the discharge line from the pump to permit adjusting flow to the unit requirement. Inlet water pressure should be measured by a pressure gauge installed in the water supply riser at the spray water inlet, and adjusted to the specified inlet pressure.

Indoor Installation (applicable to VXC and VCL models only) Many indoor installations require the use of inlet and/or discharge ductwork. Units installed with inlet ductwork must be ordered with solid-bottom panels. Generally, intake ducts are used only on smaller units while the equipment room is used as a plenum for larger units. Discharge ductwork will normally be required to carry the saturated discharge air from the building. Both intake and discharge ductwork must have access doors to allow servicing of the fan assembly, drift eliminators, and water distribution system. All ductwork is supplied and installed by others and should be symmetrical and designed to provide even air distribution across the face of air intakes and discharge openings. Such ductwork may increase the external static pressure on the unit, requiring a larger fan motor to be installed. This external static pressure must be quantified (in Pa) to BAC to allow for suitable fan motor sizing. Warning: The discharge opening must be positioned to prevent the introduction of discharge air into the fresh air intakes serving the unit or the ventilation systems of adjacent buildings.

Note: Axial fan units are not suitable for indoor installations.

Baltimore Aircoil

EC - E 9

Safety Adequate precautions, appropriate for the installation and location of these products, should be taken to safeguard the public from possible injury and the equipment and the premises from damage. Operation, maintenance and repair of this equipment should be undertaken only by personnel qualified to do so. Proper care, procedures and tools must be used in handling, lifting, installing, operating, maintaining, and repairing this equipment to prevent personal injury and/or property damage.

All evaporative condenser coils supplied from Europe, including desuperheater coils, are certified according to the European Pressure Equipment Directive 97/23/EC. Since November 1999 this Pressure Equipment Directive has been adopted by the national legislation of all EU and EFTA member states. The PED 97/23/EC specifies the design, manufacturing, quality and documentation requirements for pressure vessels and replaces previous national code requirements. BAC evaporative condenser coils fall under Category IV of the PED 97/23/EC reglementation and require a CE Declaration of Conformity which is supplied by BAC at time of shipment. Standard PED Coil design (hot-dip galvanised) All BAC evaporative condenser coils, including bare serpentine coils, split circuit coils, extended surface coils and desuperheater coils are designed as standard for a maximum operating pressure of 23 bar (minimum -1 bar). Design temperatures are minimum: -20°C and maximum +120°C. All standard PED coils are pneumatically tested at 34 bar after fabrication. Optional High pressure PED coil design (hot dip galvanised) For specific refrigerants or applications requiring higher operating pressures (> 23 bar), the high pressure coil option is available for all hot-dip galvanised condenser coil types (see above under standard PED coil design). The high pressure coils are designed for a maximum operating pressure of 28 bar (min. -1 bar) and are pneumatically tested at 40 bar. Design temperatures are minimum -20°C and maximum +120°C. Optional Stainless Steel PED coil design Bare serpentine coils only (with or without split) are available in stainless steel AISI 304 or AISI 316 execution. All stainless steel coils are designed for a maximum operating pressure of 23 bar (min. -1 bar) and are pneumatically tested at 34 bar. Design temperature limits are minimum -20°C and maximum +120°C.

Checking the refrigeration system for non-condensables and purging Source of Non-Condensables Air and other non-condensables gases collect in refrigeration systems from several sources : 1. Poor evacuation of a new system low side if operation is at pressures below atmospheric. 2. Failure to evacuate completely after part of a system has been open for repair. 3. Chemical breakdown of oil and/or refrigerant.

... because temperature matters

Evaporative Condensers

Code Requirement

EC - E 10

Overview

Test on Non-Condensables

Check the system for non-condensable gases is done during system operation. First close the valve (V3) in the liquid line running from the receiver to the evaporator (king valve). Keep the compressor running and start pumping down the system. The compressor pressure will drop as the ammonia supply has been shut off and will finally cause the compressor to fall out (security). When this happens, simultaneously close the discharge valve V1 of the compressor. The condenser is now fully pumped up with the ammonia refrigerant (which is captured between valves V1 and V3 and cannot escape). Operate the evaporative condenser for at least two hours and measure the 5 temperatures (listed below) every 10 minutes until the pan water temperature is equal to the entering wet bulb temperature (T pan = WB in). When this happens, an equilibrium has been reached in the condenser and all 5 measured temperatures should be identical to each other. If the temperature (T1, T2) corresponding to the pressure in the evaporative condenser is higher than the entering wet bulb temperature by more than 1°C, the system has an excessive amount of non-condensables (make sure that all gauges are accurate when checking for non-condensables). Five temperatures to be measured : z Entering wet bulb temperature at the condenser air inlet (WB in). z

Discharge wet bulb temperature at the condenser outlet (WB out).

z

Pan (or remote sump) water temperature (T pan).

z

Temperature (T1) equivalent to refrigerant inlet pressure of the condenser.

z

Temperature (T2) equivalent to refrigerant discharge pressure of the condenser.

Baltimore Aircoil

EC - E 11

Purge Piping All of the purge connections on the condenser coils plus the purge connection in the receiver may be cross connected to a single purge line, connected to an automatic purger. However, only one purge valve should be open at a time. Opening two or more valves tied together equalises the coil outlet pressures and the effect of the vertical drop legs is lost.

Desuperheaters The discharge gas from ammonia reciprocating compressors is highly superheated. A desuperheater removes a portion of this superheat prior to the gas entering the condensing coil, and thereby reduces the load on the evaporative condenser. Within the normal range of singlestage compressor operation, discharge gas temperatures at 13 bar discharge pressure (36°C) may run from 120°C to 150°C depending on the compression ratio, amount of suction gas superheat, and the compressor design. This represents up to 15% of the total heat rejection load. Other refrigerants and compressor types generally have much lower discharge gas temperatures than the ammonia reciprocating system so a desuperheater is usually impractical for these applications.

Ammonia Reciprocating Compressors generate significant superheat

The desuperheater coil is located on top of the condenser, above the drift eliminators.

An enhanced surface coil encased by galvanised steel panels will be fitted onto the evaporative condenser in the discharge air stream. The coil has a design for low pressure drop and is in complete compliance to the PED code requirements for a 23 bar design pressure. Optional high pressure PED coils are available designed for 28 bar operating pressure. The coil is a two pass arrangement with the entering and leaving gas connections at the same end; thus keeping all coil connections at the same end of the evaporative condenser. The coil is hot dip galvanised after fabrication and mounted into a completely enclosed plenum with access doors to allow inspection and maintenance of the drift eliminators and spray section. The piping between the desuperheater coil and the condenser coil is to be field fabricated and installed by the contractor.

... because temperature matters

Evaporative Condensers

Purge Connections The several recommended piping arrangements each show purge valves at two different locations, i.e. at the high point of the system and at each condensing coil outlet. Purging at the high point of the system can only be effective when the system is down. During normal operation the non-condensables are dispersed throughout the high velocity refrigerant vapour and too much refrigerant would be lost when purging from this high point. However, purging at the condenser coil outlet can be effectively accomplished during system operation. The non-condensables will carry through the condenser coil with the refrigerant liquid and vapour and tend to accumulate in the condensing coil outlet header and connection where the temperature and velocity are relatively low.

EC - E 12

Refrigerant Liquid Subcooling

Overview

The pressure at the expansion device feeding the evaporator(s) can be substantially lower than the receiver pressure due to liquid line pressure losses. If the liquid line is long or the evaporator is above the receiver, which further reduces the pressure at the expansion device, significant flashing can occur in the liquid line. To avoid liquid line flashing where the above conditions exist, it is necessary to subcool the liquid refrigerant after it leaves the receiver. The minimum amount of subcooling required is the temperature difference between the condensing temperature and the saturation temperature corresponding to the pressure at the expansion device. To determine the degree of subcooling required, it is necessary to calculate the liquid line pressure drop including valves, ells, tees, strainers, etc., and add to it the pressure drop equivalent to the static head loss between the receiver and the expansion device at the evaporator, if the evaporator is located above the receiver. Some compressor manufacturers publish their compressor ratings based on a fixed amount of subcooling at the expansion device. Subcooled liquid at the expansion device of the evaporator does increase system capacity since it increases the refrigeration effect per litre refrigerant circulated. But the increase is relatively small and seldom justifies the cost of the subcooling device and piping for this reason alone. However, where compressor ratings based on subcooled liquid are used, the specified amount of subcooling must be added to that required for liquid line pressure drop and static head loss. Note: Increasing the evaporative condenser size over the capacity required for the system will not produce liquid subcooling. The increased condenser capacity will result only in lower operating condensing temperatures. The same result will occur if the condensing coil is piped directly to the subcooling coil.

Low temperature, multistage ammonia (R-717) refrigeration systems often use liquid subcooling between stages for more economical operation. However, subcooling coils in an evaporative condenser are seldom, if ever, used with an ammonia refrigeration system for several reasons and are not available from BAC: 1. Design condensing temperatures are generally lower with ammonia, thus limiting the amount of subcooling that can be obtained. 2. The density of ammonia liquid is approximately 37 pounds per cubic foot, less than half that of the normally used halocarbons, and static head losses are proportionately less. 3. The expansion devices and system designs normally used for ammonia systems are less sensitive to small amounts of flash gas. 4. The high latent heat of ammonia (approximately 7110 kJ/kg versus 163 kJ/kg for R-22) results in comparatively small amounts of flash gas with a liquid line properly sized for low pressure drop. Note: Subcooling coils are not available from BAC.

Warranties Please refer to the Limitation of Warranties applicable to and in effect at the time of the sale/ purchase of these products.

Baltimore Aircoil

VXC - E 1

VXC

Evaporative Condensers

VXC Evaporative Condensers ................................................................. E2 Benefits ....................................................................................................... E4 Construction Details .................................................................................. E6 Custom Features and Options .................................................................. E8 Accessories ............................................................................................... E10 Engineering Data ..................................................................................... E12 Structural Support .................................................................................. E19 Engineering Specifications ..................................................................... E21

Evaporative Condensers

Product Detail

VXC - E 2

VXC Evaporative Condensers Capacity Single Model Capacity: VXC : 50 – 6470 Nominal R717 kW’s

VXC

VXC-C : 880 – 1720 Nominal R717 kW’s

General Description VXC Evaporative Condensers deliver fully rated thermal performance over a wide range of heat rejection and temperature requirements for various refrigerants. VXC and VXC-C models can be installed indoors and minimize sound levels. VXC-C models are designed to fit in standard dry van containers to minimize ocean freight costs. The Series VX occupies minimum floor space, provides year-round operating reliability and is ideal for sound sensitive applications.

Key Features z

Suitable for indoor and outdoor installations

z

Low sound

z

Low ocean freight costs (VXC-C)

z

Single side air inlet

z

Low energy consumption

z

Low installed cost

z

Easy maintenance

z

Reliable year-round operation

z

Long service life

z

Wide capacity range

z

PED 97/23/EC coil design

Baltimore Aircoil

VXC - E 3

Evaporative Condensers

... because temperature matters

VXC - E 4

Benefits Wide Capacity Range

VXC

z

Evaporative condenser capacity - The evaporative condensers are available in a broad range of unit capacities, with small capacity increments to permit close matching of unit size to design load. The VX line offers the widest selection of evaporative condensers in the industry to meet virtually every installation and application need.

Installation and Application Flexibility z

Indoor Installations – Centrifugal fans can overcome the static pressure imposed by external ductwork, allowing these units to be installed indoors.

Low Sound z

z

Centrifugal Fan - Centrifugal fans have inherently low sound characteristics. Single Side Air Inlet - Particularly sound-sensitive areas can be accommodated by facing the quiet side (back panel) to the sound-sensitive direction.

Low Ocean Freight Cost z

Size - C models are designed to fit in standard closed box containers to minimize ocean freight costs. All containerized models are shipped in a bottom fan section and a top coil section, which fit together into a 40' box container, no crating required. In order to fit the bottom fan section through the doors of the container, the fan enclosures are shipped loose inside the water basin area and are easily mounted on site.

C Model in Dry Van Container

Baltimore Aircoil

Fan Enclosures are shipped loose

VXC - E 5

Low Energy Consumption z

z

Evaporative Cooling Equipment minimizes the energy consumption of the entire system because it provides lower operating temperatures. The owner saves money while conserving natural resources and reducing environmental impact. Evaporative Condensers provide lower condensing temperatures and can offer significant kW savings over conventional air-cooled and water-cooled condensing systems.

z

z

Support – All models mount directly on two parallel I-beams (supplied by others) and ship complete with motors and drives, factory-installed and aligned. Modular Design – Large models ship in multiple sections to minimize the size and weight of the heaviest lift, allowing for the use of smaller, less costly cranes.

Easy Maintenance z

Internal Access - The interior of the unit is easily accessible for adjusting the float valve, cleaning the strainer or flushing the basin.

Reliable Year-Round Operation z

V-Belt Drive – The fans, motor, and drive system are located outside of the moist discharge airstream, protecting them from moisture, condensation and icing hence allowing a safe yearround operation.

Long Service Life z

Materials of Construction – Various materials are available to meet the corrosion resistance, unit operating life, and budgetary requirements of any project.

Note: For more information, please refer to the section “Technical Resources, Materials of Construction”.

The water level control is easily reached from the access door.

External V-belt drive system (shown here with panel removed)

... because temperature matters

Evaporative Condensers

Low Installed Cost

VXC - E 6

VXC

Construction Details

Upper Section

Lower Section

Baltimore Aircoil

VXC - E 7

1. Heavy Duty Construction z

Z600 hot-dip galvanized steel panels

2. Water Distribution System Plastic spray header and branches

z

Large orifice, non-clog nozzles

z

Grommetted for easy maintenance

3. Coil z

Coil according to European Pressure Equipment Directive 97/23/EC

z

Continuous serpentine, steel tubing

z

Hot-dip galvanized after fabrication (HDGAF)

z

Pneumatically tested at 34 bar standard coil

z

Sloped tubes for free drainage of fluid

4. Drift Eliminators z

UV resistant non-corrosive material, impervious to rot, decay and biological attack

z

Three distinct changes in air direction to reduce drift loss significantly

z

Assembled in easy to handle sections, which can be removed for access to the equipment interior

5. Fan Drive System z

V-belt drive

z

Heavy-duty bearings and fan motor

6. Centrifugal Fan(s) z

Quiet Operation

7. Recirculating Spray Pump z

Close coupled, bronze fitted centrifugal pump

z

Totally enclosed fan cooled (TEFC) motor

z

Bleed line with metering valve installed from pump discharge to overflow

8. Access Door z

Circular access door

9. Strainer (not shown) z

Anti-vortex design to prevent air entrainment

... because temperature matters

Evaporative Condensers

z

VXC - E 8

Custom Features and Options Construction Options

VXC

z

z

Standard Construction: Steel panels and structural elements are constructed of Z600 heavy-gauge hot-dip galvanized steel protected with the Baltiplus Corrosion Protection on the outside of the unit. Optional BALTIBOND® Corrosion Protection System: The BALTIBOND® Corrosion Protection System, a hybrid polymer coating used to extend equipment life, is applied before assembly to all hot-dip galvanized steel components of the unit.

z

Optional Stainless Steel Construction: Steel panels and structural elements are constructed of stainless steel either type 304 or 316.

z

Optional Water-Contact Stainless Steel Cold Water Basin: A cost-effective alternative to an all stainless steel unit. The critical components in the cold water basin and the cold water basin itself are provided in stainless steel. The remaining components are protected with the BALTIBOND® Corrosion Protection System.

Note: See section Technical Resources, Material of Construction for more details on the materials described above.

Coil Configurations Each coil is manufactured according to the European Pressure Equipment Directive (PED) 97/23/EC (For more details, refer to the Evaporative Condenser "Overview" section) BAC condenser coils are standard available at a design pressure of 23 bar, and are pneumatically tested at 34 bar. z

Standard Serpentine Coil: The standard condensing coil is constructed of continuous lengths of all prime surface steel, hot-dip galvanised after fabrication (HDGAF).

z

Multiple Circuit Coils (Split Coils): In general, multiple circuit coils are required primarily on halocarbon refrigerant systems where it is common practice to maintain individual compressor systems. Also, a circuit can be isolated to provide cooling of a water or glycol loop for compressor jacket cooling. A wide range of multiple circuit arrangements are available.

z

Optional Extended Surface Coil: Coils are available with selected rows finned at 3 to 5 fins per inch for wet/dry applications. The coil is hot-dip galvanised after fabrication (HDGAF).

z

Optional Stainless Steel Coil: Coils are available in Type 304L or 316L stainless steel for specialised applications.

z

Optional High Pressure Coil: Coils are available with a design pressure of 28 bar and pneumatically tested at 40 bar. The Coil is hot-dip galvanised after fabrication (HDGAF).

Hot Dip Galvanised Coil

All coils are designed for low pressure drop with sloping tubes for free drainage of fluid.

Baltimore Aircoil

VXC - E 9

Fan Drive System The fan drive system provides the cooling air necessary to reject heat from the system to the atmosphere. Centrifugal fans, forwardly curved, are driven by matched V-belts with taper lock sheaves.

The Baltiguard® Drive System

Low Sound Operation The low sound levels generated by BAC Products with centrifugal fans make them suitable for most installations. For situations when one direction is particularly sound sensitive, the unit can be oriented so that the side opposite the air inlet faces the sound-sensitive direction. Units with centrifugal fans are also available with factory designed, tested and rated sound attenuation for both the air inlet and discharge. Note: For more information, please refer to the section “Technical Resources, Sound Reduction Options”.

Remote Sump Execution The use of an auxiliary sump within a heated space is the most satisfactory way to protect sump water from freezing. When the circulating pump is shut off, all the water in the water distribution, in suspension and in the sump will drain freely to the auxiliary sump. Note: For detailed information on the calculation of the remote sump tank, please refer to the section "Technical Resources, Selection of Remote Sump Tank".

Baltiguard® Drive System

Unit with Intake and Discharge Sound Attenuation

... because temperature matters

Evaporative Condensers

The BALTIGUARD® Drive System consists of two standard single-speed fan motors and drive assemblies. One drive assembly is sized for full speed and load, and the other is sized for approximately 2/3 speed and consumes only 1/3 of the design kilowatt power. This configuration allows the system to be operated like a two-speed motor, but with the reserve capacity of a standby motor in the event of failure. As a minimum, approximately 70% capacity will be available from the low kilowatt motor, even on a design wet-bulb day. Controls and wiring are the same, as those required for a two-speed, two-winding motor. Significant energy savings are achieved when operating at low speed during periods of reduced load and/or low wet-bulb temperatures.

VXC - E 10

Accessories Ladder, Safety Cage and handrails

VXC

In the event the owner requires easy access to the top of the unit, the unit can be furnished with ladders extending from the base of the unit to the top, as well as safety cages, and handrail packages. Note: When these access options are employed, the unit must be equipped with steel drift eliminators.

Electric Water Level Control Package The electric water level control replaces the standard mechanical make-up valve when a more precise water level control is required. This Ladder and Safety Cage, Handrails around top of Unit package consists of a float switch mounted in the basin and a solenoid activated valve in the makeup water line. The valve is slow closing to minimize water hammer.

Extended Lubrication Lines Extended lubrication lines with grease fittings are available for lubrication of the fan shaft bearings.

Basin Heaters Units exposed to below freezing ambient temperatures require protection to prevent freezing of the water in the cold water basin when the unit is idle. Factory-installed heaters, which maintain the water temperature at 4°C, are a simple and inexpensive way of providing such protection. The heater package includes the heaters, a thermostat and a low level cut out switch to protect the heaters if the water level is too low. Standard electric heaters are selected for -18°C ambient temperature.

Extended Lubrication Lines

Model No. VXC

Heater -18°C (kW)

14-28

1 x 1,5

36-65

1 x 1,5

72-97

1 x 2,5

110-135

1x3

150-205

1x4

221-454

1x6

495-516

2x4

562-680

2x5

714-908 / 715-804

2x6

990-1032

4x4

Baltimore Aircoil

VXC - E 11

Model No. VXC

Heater -18°C (kW)

1124-1360

4x5

1430-1608

4x6

S288-S350

1x6 2x4 2x6

S806-S1010

4x4

C220 - C287

1x6

C325 - C426

2x4

Solid Bottom Panels Factory-installed bottom panels are required when intake air is ducted to the unit.

Discharge Hoods Discharge hoods reduce the risk of re-circulation in tight enclosures by increasing discharge air velocity, and can be used to elevate the unit discharge above adjacent walls to comply with layout guidelines.

Desuperheater Desuperheaters can be used in R-717 systems with reciprocating compressors. They increase the capacity of the standard model and extend the dry operation capacity. They are also effective in reducing the occurrence of visible plumes.

Steel Eliminators Steel eliminators with Baltibond® Corrosion Protection System are available for specific applications.

N2 Filling of the Coil For prolonged shipment periods (ocean freight) or extended storage on site it is recommended to charge the coil(s) with nitrogen.

Basin Sweeper Piping Basin sweeper piping provides an effective method of preventing sediment from collecting in the cold water basin of the unit. A complete piping system, including nozzles, is provided in the unit basin for connection to side stream filtration equipment. Note: For more information, please refer to the section "Technical Resources, Filtration".

Basin Sweeper Piping

... because temperature matters

Evaporative Condensers

S403-S504 S576-S700

VXC - E 12

Engineering Data REMARK: Do not use for construction. Refer to factory certified dimensions & weights. This brochure includes data current at time of publication, which should be reconfirmed at the time of purchase. In the interest of product improvement, specifications, weights and dimensions are subject to change without notice. Up-to-date engineering data and more can be found at www.BaltimoreAircoil.com.

VXC

VXC 14 - VXC 265

1. For VXC 14 through VXC 28: refrigerant in ND 80; 2. For VXC 14 through VXC 28: refrigerant out ND 80: 3. For VXC 36 through VXC 265: refrigerant in ND 100; 4. For VXC 36 through VXC 265: refrigerant out ND 100; 5. Make-up; 6. Overflow; 7. Drain; 8. Access (models 14

Model

Operating Weight (kg)

Shipping Weight (kg)

Heaviest Section Coil (kg)

H (mm)

L (mm)

W (mm)

Air Flow (m3/s)

Fan Motor (kW)

Water Flow (l/s)

Pump Motor (kW)

R717 Charge (kg)

VXC 14 VXC 18 VXC 25 VXC 28

660 740 830 900

600 670 760 830

580* 660* 480 540

2035 2245 2467 2683

914 914 914 914

1207 1207 1207 1207

2,3 2,2 2,5 2,4

(1x) 1,5 (1x) 1,5 (1x) 2,2 (1x) 2,2

2,2 2,2 2,2 2,2

(1x) 0,25 (1x) 0,25 (1x) 0,25 (1x) 0,25

9 11 15 19

VXC 36 VXC 45 VXC 52 VXC 59 VXC 65

1050 1170 1310 1330 1500

920 1030 1160 1180 1330

920* 1030* 700 700 860

2035 2245 2467 2467 2683

1829 1829 1829 1829 1829

1207 1207 1207 1207 1207

4,6 5,0 4,8 5,3 5,5

(1x) 4,0 (1x) 4,0 (1x) 4,0 (1x) 5,5 (1x) 5,5

4,7 4,7 4,7 4,7 4,7

(1x) 0,37 (1x) 0,37 (1x) 0,37 (1x) 0,37 (1x) 0,37

16 20 29 29 36

VXC 72 VXC 86 VXC 97

1810 1820 2080

1490 1500 1730

1000 1000 1200

2578 2578 2813

2737 2737 2737

1207 1207 1207

5,8 7,5 7,1

(1x) 4,0 (1x) 7,5 (1x) 7,5

7,1 7,1 7,1

(1x) 0,75 (1x) 0,75 (1x) 0,75

41 41 50

VXC 110 VXC 125 VXC 135

2240 2510 2540

1800 2050 2080

1200 1440 1440

2578 2813 2813

3658 3658 3658

1207 1207 1207

10,4 9,9 10,9

(1x) 7,5 (1x) 7,5 (1x) 11,0

9,5 9,5 9,5

(1x) 0,75 (1x) 0,75 (1x) 0,75

59 73 73

VXC 150 VXC 166 VXC 185 VXC 205

3210 3240 3670 3980

2640 2670 2950 3255

1720 1720 1980 2240

3093 3093 3328 3563

3645 3645 3645 3645

1438 1438 1438 1438

13,3 15,8 15,7 16,9

(1x) 7,5 (1x) 11,0 (1x) 11,0 (1x) 15,0

13,9 13,9 13,9 13,9

(1x) 1,5 (1x) 1,5 (1x) 1,5 (1x) 1,5

77 77 104 111

VXC 221 VXC 250 VXC 265

5860 6390 6435

4250 4770 4815

2630 3150 3150

3585 3820 3820

3550 3550 3550

2397 2397 2397

21,9 21,2 22,7

(1x) 15,0 (1x) 15,0 (1x) 18,5

19,2 19,2 19,2

(1x) 2,2 (1x) 2,2 (1x) 2,2

118 146 146

* Unit normally ships in one piece.

Baltimore Aircoil

VXC - E 13

VXC S288 - VXC S1010

Model

Operating Weight (kg)

Shipping Weight (kg)

Heaviest Section (coil) (kg)

H (mm)

L (mm)

W (mm)

Air Flow (m3/s)

Fan Motor (kW)

Water Flow (l/s)

Pump Motor (kW)

R717 Charge (kg)

VXC S288 VXC S300 VXC S328 VXC S350

7600 7630 7705 8320

5525 5555 5630 6180

3850 3850 3850 4470

4248 4248 4248 4483

3550 3550 3550 3550

2397 2397 2397 2397

22,8 24,2 26,7 26,2

(1x) 18,5 (1x) 22,0 (1x) 30,0 (1x) 30,0

25,2 25,2 25,2 25,2

(1x) 2,2 (1x) 2,2 (1x) 2,2 (1x) 2,2

164 164 164 196

VXC S403 VXC S429 VXC S455 VXC S482 VXC S504

10225 10285 11270 11320 12500

7170 7230 8125 8175 9260

4715 4715 5710 5710 6690

4013 4013 4248 4248 4483

5385 5385 5385 5385 5385

2397 2397 2397 2397 2397

36,6 38,9 34,9 37,5 36,6

(1x) 30,0 (1x) 37,0 (1x) 30,0 (1x) 37,0 (1x) 37,0

38,5 38,5 38,5 38,5 38,5

(1x) 4 (1x) 4 (1x) 4 (1x) 4 (1x) 4

198 198 246 246 294

VXC S576 VXC S600 VXC S656 VXC S700

15120 15220 15400 16655

10880 10980 11100 12355

3840 3840 3840 4470

4248 4248 4248 4483

7226 7226 7226 7226

2397 2397 2397 2397

45,6 48,4 53,4 52,4

(2x) 18,5 (2x) 22,0 (2x) 30,0 (2x) 30,0

50,4 50,4 50,4 50,4

(2x) 2,2 (2x) 2,2 (2x) 2,2 (2x) 2,2

328 328 328 392

VXC S806 VXC S858 VXC S910 VXC S964 VXC S1010

20555 20755 22570 22770 25035

14415 14615 16420 16550 18505

5120* 5120* 5710 5710 6690

4013 4013 4248 4248 4483

10903 10903 10903 10903 10903

2397 2397 2397 2397 2397

73,2 77,8 69,8 75,0 73,2

(2x) 30,0 (2x) 37,0 (2x) 30,0 (2x) 37,0 (2x) 37,0

77,0 77,0 77,0 77,0 77,0

(2x) 4 (2x) 4 (2x) 4 (2x) 4 (2x) 4

396 396 492 492 588

* Pan section is the heaviest section.

... because temperature matters

Evaporative Condensers

1. Refrigerant in ND 100; 2. Refrigerant out ND 100; 3. Make-up ND 50; 4. Overflow ND 80; 5. Drain ND 50; 6. Access

VXC - E 14

VXC

VXC 357 - VXC 1360

1. Refrigerant in ND 100; 2. Refrigerant out ND 100; 3. Make-up; 4. Overflow ND 80; 5. Drain ND 50; 6. Access; For VXC 357 through VXC 908: make-up ND 50; For VXC 1124 through VXC 1360 Make-up ND 80.

Model

Operating Weight (kg)

Shipping Weight (kg)

Heaviest Section (coil) (kg)

H (mm)

L (mm)

W (mm)

Air Flow (m3/s)

Fan Motor (kW)

Water Flow (l/s)

Pump Motor (kW)

R717 Charge (kg)

VXC 357 VXC 399 VXC 454

6940 8290 9580

5300 6600 7860

3940 4730 5510

4075 4310 4545

3550 3550 3550

3000 3000 3000

34,3 31,6 34,4

(1x) 22,0 (1x) 22,0 (1x) 30,0

30,8 30,8 30,8

(1x) 4 (1x) 4 (1x) 4

180 218 250

VXC 562 VXC 620 VXC 680

11490 12680 14100

8990 10200 11530

5810 7010 8200

4075 4310 4545

5388 5388 5388

3000 3000 3000

51,2 50,0 52,0

(2x) 18,5 (2x) 18,5 (2x) 22,0

46,7 46,7 46,7

(1x) 4 (1x) 4 (1x) 4

250 350 390

VXC 714 VXC 798 VXC 908

14430 16590 19140

10600 13200 15700

3940 4730 5510

4075 4310 4545

7226 7226 7226

3000 3000 3000

68,6 63,2 68,8

(2x) 22,0 (2x) 22,0 (2x) 30,0

61,6 61,6 61,6

(2x) 4 (2x) 4 (2x) 4

360 436 500

VXC 1124 VXC 1240 VXC 1360

22740 25240 28090

17940 20380 23100

5810* 7010 8200

4075 4310 4545

10903 10903 10903

3000 3000 3000

102,4 100,1 104,0

(4x) 18,5 (4x) 18,5 (4x) 22,0

93,4 93,4 93,4

(2x) 4 (2x) 4 (2x) 4

500 700 780

* Pan Section is the heaviest section.

Baltimore Aircoil

VXC - E 15

VXC 495 - VXC 1608

Model

Operating Weight (kg)

Shipping Weight (kg)

Heaviest Section (coil) (kg)

H (mm)

L (mm)

W (mm)

Air Flow (m3/s)

Fan Motor (kW)

Water Flow (l/s)

Pump Motor (kW)

R717 Charge (kg)

VXC 495 VXC 516

12040 13030

8210 9170

5610 6550

4310 4545

3550 3550

3607 3607

40,0 39,4

(1x) 37,0 (1x) 37,0

39,1 39,1

(1x) 4 (1x) 4

250 298

VXC 715 VXC 772 VXC 804

17555 17735 19290

11855 12035 13435

8310 8310 9710

4310 4310 4545

5388 5388 5388

3607 3607 3607

56,1 62,3 60,4

(2x) 22,0 (2x) 30,0 (2x) 30,0

56,8 56,8 56,8

(1x) 4 (1x) 4 (1x) 4

374 374 450

VXC 990 VXC 1032

24185 26095

16520 18280

5610 6550

4310 4545

7226 7226

3607 3607

80,0 78,8

(2x) 37,0 (2x) 37,0

78,2 78,2

(2x) 4 (2x) 4

500 596

VXC 1430 VXC 1544 VXC 1608

35200 35560 38665

23680 23770 26845

8300 8300 9710

4310 4310 4545

10903 10903 10903

3607 3607 3607

112,2 124,6 120,8

(4x) 22,0 (4x) 30,0 (4x) 30,0

113,6 113,6 113,6

(2x) 4 (2x) 4 (2x) 4

748 748 900

... because temperature matters

Evaporative Condensers

1. Refrigerant in ND 100; 2. Refrigerant out ND 100; 3. Make-up; 4. Overflow ND 80; 5. Drain ND 50; 6. Access. For VXC 495 through VXC 1032 : Make-up ND50; For VXC 1430 through VXC 1608: Make-up ND 80.

VXC - E 16

VXC

VXC C220 - VXC C426

1. Refrigerant in ND 100; 2. Refrigerant out ND 100; 3. Make-up ND 50; 4. Overflow ND 80; 5. Drain ND 50; 6. Access Fan covers are shipped loose.

Model

Operating Weight (kg)

Shipping Weight (kg)

Heaviest Section (coil) (kg)

H (mm)

L (mm)

W (mm)

Air Flow (m3/s)

Fan Motor (kW)

Water Flow (l/s)

Pump Motor (kW)

R717 Charge (kg)

VXC C220 VXC C250 VXC C265 VXC C287

5940 6415 6440 7450

4250 4770 4795 5315

2630 3150 3150 3665

3585 3820 3820 4055

3550 3550 3550 3550

2245 2245 2245 2245

20,6 20,1 21,7 22,5

(1x) 15,0 (1x) 15,0 (1x) 18,5 (1x) 22,0

19,2 19,2 19,2 19,2

(1x) 2,2 (1x) 2,2 (1x) 2,2 (1x) 2,2

118 146 146 154

VXC C325 VXC C340 VXC C380 VXC C408 VXC C426

8730 8735 9430 9470 10260

6135 6145 6945 7030 7830

3885 3885 4685 4685 5485

3585 3585 3820 3820 4055

5385 5385 5385 5385 5385

2245 2245 2245 2245 2245

31,5 33,5 32,2 35,5 34,7

(1x) 18,5 (1x) 22,0 (1x) 22,0 (1x) 30,0 (1x) 30,0

29,0 29,0 29,0 29,0 29,0

(1x) 4 (1x) 4 (1x) 4 (1x) 4 (1x) 4

156 156 196 196 234

General Notes 1. Standard refrigerant connection sizes are ND 100 BSP MPT inlet and outlet (for models VXC 14 through 28 refrigerant connection sizes are ND 80 BSP MPT), consult your local BAC representative for size and location. Other connection sizes are available on special order. Refrigerant connections are standard bevelled for welding. 2. Make up, overflow, suction, drain connections and access door can be provided on side opposite to that shown; consult your BAC Balticare representative. 3. Unit height is indicative, for precise value refer to certified print. 4. Shipping/operating weights indicated are for units without accessories such as sound attenuators, discharge hoods, etc. Consult factory certified prints to obtain weight additions and the heaviest section to be lifted. 5. The drawings for units with only one spray pump show the standard “right hand” arrangement, which has the air inlet side on the right when facing the connection end. “Left hand” arrangement can be furnished by special order. 6. Coil, overflow, make-up and spray water connections are always located on the same end of the unit. For double pump units an additional set of coil connections and an additional overflow connection will be installed on the other end of the unit.

8. For indoor applications of evaporative condensers, the room may be used as a plenum with ductwork attached to the discharge only. If inlet ductwork is required, an enclosed fan section must be specified; consult your BAC representative for details. 9. Fan kW is at 0 Pa ESP. To operate against external static pressure up to 125 Pa, increase each fan motor one size. 10.Refrigerant charge listed is R 717 operating charge. To determine operating charge of R22 refrigerants, multiply by: 1,93. For R134A, multiply by: 1,98. 11.For dry operation, standard motors must be increased one size to avoid motor overloading. Extended surface coils are available to vastly increase dry capacity without motor size increase. Consult your local BAC Balticare representative for selection and pricing. 12.Models VXC 357-454, VXC 562-380, VXC 495-516 and VXC 715-804 have only 1 coil casing section and one or two fan motors. Fan cycling results in only on-off operation. On these units all fans need to operate simultaneously. 13.Models VXC 714-907, VXC 1124-1360, VXC 990-1032 and VXC 1430-1608 have 2 coil casing sections and one or two fan motors per coil casing section. Fan cycling results in only on-off operation. On these units all fans need to operate simultaneously per coil casing section.

7. On models VXC 14 through VXC 135 access doors are located at the opposite of the air inlet side, ensure sufficient space for entry when positioning these units.

Baltimore Aircoil

VXC - E 17

Sound Attenuation XA + XB Sound Attenuation

XC Sound Attenuation

1. Access Door; L1= Intake Attenuator Length; L2= Discharge Attenuator Length; W= Unit Width; H.= Unit Height (see Engineering Data).

... because temperature matters

Evaporative Condensers

1. Access Door; L1= Intake Attenuator Length; L2= Discharge Attenuator Length; W= Unit Width; H.= Unit Height (see Engineering Data).

VXC - E 18

VXC

VXC

Unit + Atten. # pieces shipped

Dimensions (mm)

# Access doors (2)

XA, XB, XC

W2

H1

W1

Weights (kg) L1

XA, XB, XC

Disch. Att.

Int. Att.

14 - 28

4(1)

1

2

2352

N.A. 1090 1030

890

36 - 65

4(1)

1

2

2352

XA, XB XC

L2

XA, XB, XC

Intake

Discharge

XA

XB

XC

902

110

130 N.A.

N.A. 1090 1030 1800

1816

175

220 N.A.

Solid Bottom

XC

Total

XA

XB

XA

XB

XC

30

130

150 N.A. 270

310

N.A.

50

175

220 N.A. 400

490

N.A.

72 - 97

4

1

2

2352

N.A. 1090 1030 2710

2731

230

300 N.A.

70

280

350 N.A. 580

720

N.A.

110 - 135

4

1

2

2352

N.A. 1090 1030 3635

3645

300

370

830

100

360

420 N.A. 760

890

N.A.

150 - 205

4

1

2

2583

3728 1600 1420 3635

3645

380

480 1080

120

440

520 1070 940 1120 2270

221 - 265

4

1

2

3542

4687 2070 1955 3525

3645

500

630 1420

190

530

650 1330 1220 1470 2940

S288 - S350

4

1

2

3542

4687 2070 2365 3525

3645

500

630 1420

190

660

800 1640 1350 1620 3250

S403 - S504

4

2

2

3542

4687 2070 2365 5365

5480

660

860 1970

300

830 1090 2240 1790 2250 4510

S576 - S700

7

2

2

3542

4687 2070 2365 7050

7322 1000 1260 2840

380

1320 1600 3280 2700 3240 6500

S806 S1010

7

4

2

3542

4687 2070 2365 10730 10998 1320 1720 3940

600

1660 2180 4480 3580 4500 9020

357 - 454

4

1

2

4145

5290 2560 2965 3525

3645

560

710 1620

230

710

562 - 680

4

2

2

4145

5290 2560 2965 5365

5480

730

980 2240

350

900 1210 2490 1980 2540 5080

714 - 908

7

2

2

4145

5290 2560 2965 7050

7322 1120 1420 3240

460

1420 1760 3640 3000 3640 7340

1124 - 1360

7

4

2

4145

5290 2560 2965 10730 10994 1460 1960 4480

700

1800 2420 4980 3960 5080 10160

495 - 516

4

1

2

4752

5897 2560 3575 3525

3645

560

710 1620

280

810 1030 2130 1650 2020 4030

715 - 804

4

2

2

4752

5897 2560 3575 5365

5480

730

980 2240

420

1020 1410 2920 2170 2810 5580

990 - 1032

7

2

2

4752

5897 2560 3575 7050

7322 1120 1420 3240

560

1620 2060 4260 3300 4040 8060

1430 - 1608

7

4

2

4752

5897 2560 3575 10730 10994 1460 1960 4480

840

2040 2820 5840 4340 5620 11160

(1)

880 1820 1500 1820 3670

VXC 14, VXC 18, VXC-36 and VXC-45 + Attenuator are shipped in 3 pieces

(2) Intake Attenuator: Access opening is 775 mm high, 405 mm wide and is located at each end of the unit. Discharge Attenuator : Access opening is 405 mm high, 1170 mm wide and is located at blank off side of the unit (VXC14-28 has 650 mm width)

Remote Sump Data Refer to the "Technical Resources" section "Selection of Remote Sump" for Remote Sump Data.

Baltimore Aircoil

VXC - E 19

Structural Support REMARK: Do not use for construction. Refer to factory certified dimensions & weights. This brochure includes data current at time of publication, which should be reconfirmed at the time of purchase. In the interest of product improvement, specifications, weights and dimensions are subject to change without notice. Up-to-date engineering data and more can be found at www.BaltimoreAircoil.com. The recommended support arrangement for units consists of parallel I-beams running the full length of the unit, spaced as shown in the following drawing. Besides providing adequate support, the steel also serves to raise the unit above any solid foundation to ensure access to the bottom of the unit. To support units in an alternate steel support arrangement, consult your BAC Balticare Representative.

Evaporative Condensers

Units without Sound Attenuation

1. Outline of Unit; 2. Mounting holes Ø 22 mm, 3. Unit; 4. Air Intake.

C D Center dis. Center dis. Length Width (mm) (mm)

A Unit Length (mm)

B Unit width (mm)

VXC 14-28

914

1207

750

VXC 36-65

1829

1207

1664

VXC 72-97

2737

1207

VXC 110-135

3658

Model

E (mm)

F (mm)

G (mm)

X Max. Deflection (mm)

Mounting holes

1153

-

-

-

2

4

1153

-

-

-

5

4

2572

1153

-

-

-

8

4

1207

3492

1153

-

-

-

10

4

VXC 150-205

3645

1438

3492

1378

-

-

-

10

4

VXC 221-265

3550

2397

3238

2397

-

-

-

10

4

VXC S288-S350

3550

2397

3238

2327

-

-

-

10

4

VXC S403-S504

5385

2397

5074

2327

2486

102

-

13

8

VXC S576-S700

7226

2397

6914

2327

3238

438

-

13

8

... because temperature matters

VXC - E 20

VXC

C D Center dis. Center dis. Length Width (mm) (mm)

A Unit Length (mm)

B Unit width (mm)

VXC S806-S1010

10903

2397

10586

VXC 357-454

3550

3000

VXC 562-680

5388

3000

Model

E (mm)

F (mm)

G (mm)

X Max. Deflection (mm)

Mounting holes

2327

2486

102

438

13

16

3238

2934

-

-

-

10

4

5074

2934

2486

102

-

13

8

VXC 714-908

7226

3000

6914

2934

3238

438

-

13

8

VXC 1124-1360

10903

3000

10586

2934

2486

102

438

13

16

VXC 495-516

3550

3607

3238

3537

-

-

-

10

4

VXC 715-804

5388

3607

5074

3537

2486

102

-

13

8

VXC 990-1032

7226

3607

6914

3537

3238

438

-

13

8

VXC 1430-1608

10903

3607

10586

3537

2486

102

438

13

16

VXC C220-C287

3550

2245

3238

2175

-

-

-

10

4

VXC C325-C426

5385

2245

5074

2175

2486

102

-

13

8

Units with Sound Attenuation

1. Outline of Unit; 2. Mounting Holes Ø 22 mm; 3. Outline of attenuator (optional XA or XB);4. Support Channel attached to optional XA or XB attenuator; 5.+3. Outline of Attenuator (optional XC); 6.+4. Support Channels attached to optional XC attenuator; 7. Unit; 8. Sound Attenuator; 9. Air Intake.

Notes: 1. The recommended support arrangement for VX units consists of parallel I-beams extending the full length of the unit. Supports and anchor bolts are to be designed and furnished by others. 2. All supporting beams are to be flush and level at top and must be oriented relative to gage line as shown. 3. Recommended design loads for each unit support beam should be 70% of the total unit operating weight applied as a uniform load to each of the unit beams. The support beam(s) for the optional intake attenuator(s) needs to carry attenuator only, uniform load of 250 kg/m. Beams should be designed in accordance with

standard structural practice. For the maximum allowable deflection of beams under the unit refer to above table. 4. All mounting holes have a diameter of 22 mm at the locations shown. 5. If vibration isolators are used, a rail or channel must be provided between the unit (and optional attenuator) and the isolators to provide continuous unit support. Additionally the support beams must be designed to accommodate the overall length and mounting hole location of the isolators that may differ from those of the unit. Refer to vibration isolator drawings for these data.

Baltimore Aircoil

VXC - E 21

Engineering Specifications General A. General: Furnish and install, _____ factory assembled evaporative condenser(s) of counterflow blow-through design, with single side entry, conforming in all aspects to the specifications and schedule as shown on the plans.

D. Quality Assurance: The manufacture shall have Management System certified by an accredited registrar as complying with the requirements of ISO-9001:2000 to ensure consistent quality of products and services.

Products 1.0 Evaporative Condenser Materials and Components General: All steel panels and structural elements shall be constructed from heavy-gauge, Z600 hot-dip galvanized steel, with cut edges given a protective coating of zinc-rich compound.

2.0 Coil Casing Assembly The evaporative condenser shall include a coil casing section consisting of a refrigerant condensing coil, a spray water distribution system, and drift eliminators as indicated by the manufacturer. 1. The refrigerant condensing coil shall be fabricated of all prime surface steel at the manufacturer’s own facility, and hot-dip galvanized after fabrication. a. The refrigerant condensing coil shall be tested at 34 bar air pressure under water. b.The refrigerant condensing coil shall be designed for low pressure drop with sloping tubes for free drainage of liquid refrigerant. c. The refrigerant condensing coil shall be according to European Pressure Equipment Directive 97/23/EC.

rate sufficient to ensure complete wetting of the coil at all times by large-diameter, non-clog, 360° plastic distribution nozzles spaced across the coil face area in plastic material spray branches. Nozzles shall utilize a two-stage diffusion pattern to provide overlapping, umbrella spray patterns that create multiple intersection points with adjacent nozzles. Spray branches and nozzles shall be held in place by snap-in rubber grommets, allowing quick removal of individual nozzles or complete branches for cleaning or flushing. 3. Removable plastic material drift eliminators shall be positioned to prevent moisture from leaving the evaporative condenser and incorporate a minimum of three (3) changes in air direction.

2. Water shall be distributed evenly over the coil at a minimum flow

3.0 Pan Assembly The evaporative condenser shall include a pan assembly consisting of cold water basin with pump assembly and fan assemblies with single side air inlet and integral air plenum. 1. The cold water basin shall include: a drain/clean-out connection; a steel strainer; a brass make-up valve; overflow connection; and a water recirculation pump assembly. a. Drain/cleanout connection shall be located in the cold water basin to allow removal of recirculating water. b. Lift-out steel strainer shall be supplied with perforated openings sized smaller than the water distribution nozzle orifices and an integral anti-vortexing hood to prevent air entrainment. c. Brass make-up valve shall be supplied with a large-diameter plastic float arranged for easy adjustment. d. Overflow connection shall be provided in the cold water basin to protect against recirculating water spillage. e. Water recirculation pump shall be a close-coupled, bronze-fitted centrifugal pump equipped with a mechanical seal, mounted on the basin and piped from the suction strainer to the water distribution system. i. The pump shall be installed so that it may drain freely when the basin is drained. ii. The pump assembly shall include an integral metering valve and bleed line to control the bleed rate from the pump discharge to the overflow connection. iii. The pump motor shall be totally enclosed fan cooled (TEFC) type suitable for _____ V, ____ phase______ Hz electrical service.

f. On installations requiring a remote sump, the evaporative condenser shall be modified to accommodate the use of an independent sump and pump for recirculating water (by others) i. The recirculating water pump, steel strainer, make-up valve, and integral bleed line assemblies shall be omitted from the evaporative condenser scope of supply. ii. The evaporative condenser shall be supplied with a cold water basin outlet sized and located as indicated on the drawings for gravity drain to the remote sump. iii. The water distribution system shall have an operating pressure of 14 kPa at the evaporative condenser spray water inlet connection. 2. Air shall enter the evaporative condenser through the centrifugal fan assemblies and integral air plenum. a. Fans and motors shall be located in the dry entering airstream to provide greater reliability and ease of maintenance. b. Fan housings shall have curved inlet rings for efficient air entry and rectangular discharge cowls that extend into the pan to increase fan efficiency and prevent water from entering the fans. c. Fan(s) shall be heavy-duty, centrifugal flow type mounted on a steel shaft with heavy-duty, self-aligning, relubricatable bearings with cast iron housings, designed for a minimum L10 life of 40 000 hours. d. Fan motor(s) shall be totally enclosed fan cooled (TEFC) type, suitable for _____ V, ____ phase, ______ Hz electrical service and shall be mounted on an easily adjusted, heavy-duty motor base. Special moisture protection shall be furnished on the windings, shafts, and bearings.

... because temperature matters

Evaporative Condensers

B. Capacity: The evaporative condenser(s) shall be warranted by the manufacturer to have condensing capacity of _____ kW heat rejection, operating with ____ refrigerant and ___ºC condensing temperature and ___ºC entering wet-bulb temperature.

C. Warranty: The manufacturer’s standard equipment warranty shall be for a period of one year from the date of startup or eighteen months from the date of shipment, whichever ends first.

VXC - E 22 4.0 Optional Equipment Specifications A. Evaporative condenser shall be provided with basin heaters to prevent freezing of the water in the cold water basin when the evaporative condenser is idle.

B. Evaporative condenser shall be provided with a factory assembled, field-installed access ladder and handrails to provide access to the top of the evaporative condenser.

1. The basin heaters shall be selected to maintain +4°C basin water temperature at -18°C ambient temperature.

C. Evaporative condenser shall be supplied with the Baltiguard Drive System to improve part load efficiency and provide system redundancy in case of a motor failure. 1. The Baltiguard® Drive System shall include the main fan motor as listed in the manufacturer’s published literature and a pony motor sized for approximately 1/3 of design kW and 2/3 of design fan speed to optimize energy savings during non-design load conditions.

2. Basin heaters shall be electric immersion type controlled by a remote thermostat with the sensing bulb located in the basin water.

VXC

3. Basin heaters shall be provided with a factory-installed low water level cutout switch to prevent heater operation unless the heater elements are fully submerged.

5.0 Sound 5.1 Sound Level: To maintain the quality of the local environment, the maximum sound pressure levels (dB) measured 15 m from the

Location

63

125

250

condenser operating at full fan speed shall not exceed the sound levels detailed below.

500

Discharge Air Inlet End Back

Baltimore Aircoil

1000

2000

4000

8000

dB(A)

VCL - E 1

VCL

Evaporative Condensers

VCL Evaporative Condensers ................................................................. E2 Benefits ....................................................................................................... E4 Construction Details .................................................................................. E6 Custom Features and Options .................................................................. E7 Accessories ................................................................................................. E9 Engineering Data ..................................................................................... E10 Structural Support .................................................................................. E14 Engineering Specifications ..................................................................... E15

Evaporative Condensers

Product Detail

VCL - E 2

VCL Evaporative Condensers Capacity Single Model Capacity:

VCL

160 kW – 1290 Nominal R717 kW’s

General Description VCL Evaporative Condensers deliver fully rated thermal performance over a wide range of heat rejection and temperature requirements for various refrigerants. VCL models can be installed indoors, minimize sound levels, and are available to accommodate limited ceiling or enclosure heights. The Series VL minimizes installation costs, provides year-round operating reliability, and is ideal for sound sensitive applications.

Key Features z

Suitable for indoor and outdoor installations

z

Suitable for locations with limited ceiling or enclosure heights and roof top installations

z

Low sound

z

Single side air inlet

z

Low energy consumption

z

Low installed cost

z

Easy maintenance

z

Reliable year-round operation

z

Long service life

z

PED 97/23/EC coil design

Baltimore Aircoil

VCL - E 3

Evaporative Condensers

... because temperature matters

VCL - E 4

Benefits Installation and Application Flexibility

VCL

z

z

Indoor Installations – Centrifugal fans can overcome the static pressure imposed by external ductwork, allowing this type of unit to be installed indoors. Low Profile Models – The fan section of low profile units is adjacent to the casing section to yield models suitable for use in height sensitive installations. Low profile models are available in heights of 1585 mm up to 2560 mm.

Low Sound z

z

Low profile unit shown in contrast to a standard unit

Centrifugal Fan - Centrifugal fans have inherently low sound characteristics. Single Side Air Inlet - Particularly soundsensitive areas can be accommodated by facing the quiet side (back panel) to the soundsensitive direction.

Low Energy Consumption z

z

Evaporative Cooling Equipment minimizes the energy consumption of the entire system because it provides lower operating temperatures. The owner saves money while conserving natural resources and reducing environmental impact. Evaporative Condensers provide lower condensing temperatures and can offer significant kW savings over conventional aircooled and water-cooled condensing systems.

Low Installed Cost z

z

Support – All models mount directly on two parallel I-beams (supplied by others) and ship complete with motors and drives, factoryinstalled and aligned. Modular Design – All models without intake or discharge accessories ship in one piece to minimize field installation time and lifting time.

Modular Design

Easy Maintenance z

Internal Access - The interior of the unit is easily accessible for adjusting the float valve, cleaning the strainer or flushing the basin.

Baltimore Aircoil

VCL - E 5

Reliable Year-Round Operation z

V-Belt Drive – The fans, motor, and drive system are located outside of the moist discharge airstream, protecting them from moisture, condensation and icing hence allowing a safe yearround operation.

Long Service Life z

Note: For more information, please refer to the section “Technical Resources, Materials of Construction”.

The interior of the unit is easily accessible

V-Belt Drive for Series VL

... because temperature matters

Evaporative Condensers

Materials of Construction – Various materials are available to meet the corrosion resistance, unit operating life, and budgetary requirements of any project.

VCL - E 6

VCL

Construction Details

1. Heavy Duty Construction z Z600 hot-dip galvanized steel panels

z Assembled in easy to handle sections, which can be removed for access to the equipment interior

5. Fan Drive System 2. Water Distribution System z Plastic spray header and branches z Large orifice, non-clog nozzles z Grommetted for easy maintenance

z V-belt drive z Heavy-duty bearings and fan motor

6. Centrifugal Fan(s) z Quiet Operation

3. Coil z Coil according to European Pressure Equipment Directive 97/23/EC z Continuous serpentine, steel tubing z Hot-dip galvanized after fabrication (HDGAF)

7. Recirculating Spray Pump z Close coupled, bronze fitted centrifugal pump z Totally enclosed fan cooled (TEFC) motor

z Pneumatically tested at 34 bar standard coil

z Bleed line with metering valve installed from pump discharge to overflow

z Sloped tubes for free drainage of fluid

8. Access Door

4. Drift Eliminators

z Circular access door

z UV resistant non-corrosive material, impervious to rot, decay and

biological attack z Three distinct changes in air direction to reduce drift loss significantly

9. Strainer (Not Shown) z Anti-vortex design to prevent air entrainment

Baltimore Aircoil

VCL - E 7

Custom Features and Options Construction Options z

Optional BALTIBOND® Corrosion Protection System: The BALTIBOND® Corrosion Protection System, a hybrid polymer coating used to extend equipment life, is applied before assembly to all hot-dip galvanized steel components of the unit.

z

Optional Stainless Steel Construction: Steel panels and structural elements are constructed of stainless steel either type 304 or 316.

z

Optional Water-Contact Stainless Steel Cold Water Basin: A cost-effective alternative to an all stainless steel unit. The critical components in the cold water basin and the cold water basin itself are provided in stainless steel. The remaining components are protected with the BALTIBOND® Corrosion Protection System.

Note: See section Technical Resources, Material of Construction for more details on the materials described above.

Coil Configurations Each coil is manufactured according to the European Pressure Equipment Directive (PED) 97/23/ EC (For more details, refer to the Evaporative Condenser "Overview" section) BAC condenser coils are standard available at a design pressure of 23 bar, and are pneumatically tested at 34 bar. z

Standard Serpentine Coil: The standard condensing coil is constructed of continuous lengths of all prime surface steel, hot-dip galvanised after fabrication (HDGAF).

z

Multiple Circuit Coils (Split Coils): In general, multiple circuit coils are required primarily on halocarbon refrigerant systems where it is common practice to maintain individual compressor systems. Also, a circuit can be isolated to provide cooling of a water or glycol loop for compressor jacket cooling. A wide range of multiple circuit arrangements are available.

z

Optional Extended Surface Coil: Coils are available with selected rows finned at 3 to 5 fins per inch for wet/dry applications. The coil is hot-dip galvanised after fabrication (HDGAF).

z

Optional Stainless Steel Coil: Coils are available in Type 304L or 316L stainless steel for specialised applications.

z

Optional High Pressure Coil: Coils are available with a design pressure of 28 bar and pneumatically tested at 40 bar. The Coil is hot-dip galvanised after fabrication (HDGAF).

All coils are designed for low pressure drop with sloping tubes for free drainage of fluid.

... because temperature matters

Evaporative Condensers

z

Standard Construction: Steel panels and structural elements are constructed of Z600 heavy-gauge hot-dip galvanized steel protected with the Baltiplus Corrosion Protection on the outside of the unit.

VCL - E 8

Fan Drive System The fan drive system provides the cooling air necessary to reject heat from the system to the atmosphere. Centrifugal fans, forwardly curved, are driven by matched V-belts with taper lock sheaves.

VCL

Baltiguard® Drive System The BALTIGUARD® Drive System consists of two standard single-speed fan motors and drive assemblies. One drive assembly is sized for full speed and load, and the other is sized for approximately 2/3 speed and consumes only 1/3 of the design kilowatt power. This configuration allows the system to be operated like a two-speed motor, but with the reserve capacity of a standby motor in the event of failure. As a minimum, approximately 70% capacity will be available from the low kilowatt motor, even on a design wet-bulb day. Controls and wiring are the same, as those required for a two-speed, two-winding motor. Significant energy savings are achieved when operating at low speed during periods of reduced load and/or low wet-bulb temperatures.

Low Sound Operation The low sound levels generated by BAC Products with centrifugal fans make them suitable for most installations. For situations when one direction is particularly sound sensitive, the unit can be oriented so that the side opposite the air inlet faces the sound-sensitive direction. Units with centrifugal fans are also available with factory designed, tested and rated sound attenuation for both the air inlet and discharge. Note: For more information, please refer to the section “Technical Resources, Sound Reduction Options”.

Baltiguard® Drive System

Unit with Sound Attenuation

Remote Sump The use of an auxiliary sump within a heated space is the most satisfactory way to protect sump water from freezing. When the circulating pump is shut off, all the water in the water distribution, in suspension and in the sump will drain freely to the auxiliary sump. Note: For detailed information on the calculation of the remote sump tank, please refer to the section "Technical Resources, Selection of Remote Sump Tank".

Baltimore Aircoil

VCL - E 9

Accessories Electric Water Level Control Package The electric water level control replaces the standard mechanical make-up valve when a more precise water level control is required. This package consists of a float switch mounted in the basin and a solenoid activated valve in the make-up water line. The valve is slow closing to minimize water hammer.

Extended lubrication lines with grease fittings are available for lubrication of the fan shaft bearings.

Basin Heaters Units exposed to below freezing ambient temperatures require protection to prevent freezing of the water in the cold water basin when the unit is idle. Factory-installed heaters, which maintain the water temperature at 4°C, are a simple and inexpensive way of providing such protection. The heater package includes the heaters, a thermostat and a low level cut out switch to protect the heaters if the water level is too low. Standard electric heaters are selected for -18°C ambient temperature. Model No. VCL

Heaters -18°C (kW)

VCL 042 - 079 VCL 084 - 119

1x3 1x4

VCL 131 VCL 133 VCL 140 - 159

1x5 1x4 1x5

VCL 167-235 VCL 239 - 257 VCL 258 VCL 285 - 321

2x4 2x5 2x4 2x5

N2 Filling of the Coil For prolonged shipment periods (ocean freight) or extended storage on site it is recommended to charge the coil(s) with nitrogen.

Desuperheater Desuperheaters can be used in R-717 systems with reciprocating compressors. They increase the capacity of the standard model and extend the dry operation capacity. They are also effective in reducing the occurrence of visible plumes.

Basin Sweeper Piping Basin sweeper piping provides an effective method of preventing sediment from collecting in the cold water basin of the unit. A complete piping system, including nozzles, is provided in the unit basin for connection to side stream filtration equipment. Note: For more information, please refer to the section "Technical Resources, Filtration".

Steel Eliminators Steel eliminators with Baltibond® Corrosion Protection System are available for specific applications.

... because temperature matters

Evaporative Condensers

Extended Lubrication Lines

VCL - E 10

Engineering Data REMARK: Do not use for construction. Refer to factory certified dimensions & weights. This brochure includes data

VCL

current at time of publication, which should be reconfirmed at the time of purchase. In the interest of product improvement, specifications, weights and dimensions are subject to change without notice. Up-to-date engineering data and more can be found at www.BaltimoreAircoil.com.

VCL 042 H - VCL 159 M

1. Refrigerant in ND 100; 2. Refrigerant out ND 100; 3. Access; 4. Make-up ND 25; 5. Overflow: ND 50 on VCL 042-119 & 133, ND 80 on VCL 131 & 140-159; 6. Drain ND 50; 7. Spray Pump; 8. Fan Motor.

Model VCL

Operating Weight (kg)

Shipping Weight (kg)

H (mm)

L1 (mm)

L2 (mm)

W (mm)

Air Flow (m3/s)

Fan Motor (kW)

Water Flow (l/s)

Pump Motor (kW)

R-717 Charge (kg)

VCL042-H VCL048-G VCL054-H VCL058-G VCL065-H VCL071-J VCL073-H VCL079-J

1610 1800 1810 1990 2005 2025 2190 2220

1100 1270 1280 1440 1460 1490 1640 1670

1585 1855 1855 2015 2015 2015 2230 2230

3350 3350 3350 3350 3350 3350 3350 3350

1820 1820 1820 1820 1820 1820 1820 1820

1250 1250 1250 1250 1250 1250 1250 1250

7,9 6,7 7,6 6,4 7,4 8,1 7,2 7,9

(1x) 4,0 (1x) 2,2 (1x) 4,0 (1x) 2,2 (1x) 4,0 (1x) 5,5 (1x) 4,0 (1x) 5,5

5,9 5,9 5,9 5,9 5,9 5,9 5,9 5,9

(1x) 0,55 (1x) 0,55 (1x) 0,55 (1x) 0,55 (1x) 0,55 (1x) 0,55 (1x) 0,55 (1x) 0,55

20 28 28 38 38 38 46 46

VCL084-K VCL096-J VCL102-K VCL111-L VCL115-K VCL119-M VCL133-M

2530 2810 2820 2840 3090 2845 3120

1750 2010 2020 2080 2280 2090 2350

1855 2090 2090 2090 2350 2090 2350

4560 4560 4560 4560 4560 4560 4560

2730 2730 2730 2730 2730 2730 2730

1250 1250 1250 1250 1250 1250 1250

11,4 10,2 11,2 12,3 10,8 12,4 13,0

(1x) 7,5 (1x) 5,5 (1x) 7,5 (1x) 11 (1x) 7,5 (1x) 15 (1x) 15

9,0 9,0 9,0 9,0 9,0 9,0 9,0

(1x) 0,75 (1x) 0,75 (1x) 0,75 (1x) 0,75 (1x) 0,75 (1x) 0,75 (1x) 0,75

42 55 55 55 72 55 72

VCL131-L VCL140-M VCL148-L VCL159-M

3560 3570 3930 3940

2490 2500 2830 2840

2090 2090 2350 2350

5480 5480 5480 5480

3650 3650 3650 3650

1250 1250 1250 1250

13,6 14,8 13,4 14,6

(1x) 11 (1x) 15 (1x) 11 (1x) 15

12,1 12,1 12,1 12,1

(1x) 1,1 (1x) 1,1 (1x) 1,1 (1x) 1,1

74 74 92 92

Baltimore Aircoil

VCL - E 11

VCL 167 K - VCL 321 P

Model VCL

Operating Weight (kg)

Shipping Weight (kg)

H (mm)

L1 (mm)

L2 (mm)

W (mm)

Air Flow (m3/s)

Fan Motor (kW)

Water Flow (l/s)

Pump Motor (kW)

R-717 Charge (kg)

VCL167-K VCL171-N VCL185-L VCL208-N VCL209-L VCL219-L VCL235-N VCL258-O

5260 4740 5290 5310 5860 6420 5880 6570

3650 3170 3680 3700 4210 4750 4240 4790

2090 1855 2090 2090 2350 2560 2350 2560

4560 4560 4560 4560 4560 4560 4560 4560

2730 2730 2730 2730 2730 2730 2730 2730

2400 2400 2400 2400 2400 2400 2400 2400

17,4 23,3 19,6 22,8 19,3 18,9 22,3 23,0

(1x) 7,5 (1x) 18,5 (1x) 11,0 (1x) 18,5 (1x) 11,0 (1x) 11,0 (1x) 18,5 (1x) 22,0

17,9 17,9 17,9 17,9 17,9 17,9 17,9 17,9

(1x) 1,1 (1x) 1,1 (1x) 1,1 (1x) 1,1 (1x) 1,1 (1x) 1,1 (1x) 1,1 (1x) 1,1

110 84 110 110 144 166 144 166

VCL239-L VCL257-M VCL285-O VCL286-N VCL299-O VCL321-P

7270 7280 7300 7990 8010 8110

5030 5040 5060 5690 5710 5810

2350 2350 2350 2560 2560 2560

5480 5480 5480 5480 5480 5480

3650 3650 3650 3650 3650 3650

2400 2400 2400 2400 2400 2400

20,7 22,6 25,6 23,9 25,3 27,5

(1x) 11,0 (1x) 15,0 (1x) 22,0 (1x) 18,5 (1x) 22,0 (1x) 30,0

24,2 24,2 24,2 24,2 24,2 24,2

(1x) 2,2 (1x) 2,2 (1x) 2,2 (1x) 2,2 (1x) 2,2 (1x) 2,2

184 184 184 220 220 220

General Notes 1. All models are single coil section units. Fan cycling results only in on-off operation. For additional steps of control, the Baltiguard® Drive System and two-speed fan motors are available. More precise capacity control can be obtained with modulating fan discharge dampers. 2. Make up, overflow, suction, drain connections and access door can be provided on side opposite to that shown; consult your BAC representative. 3. Unit height is indicative, for precise value refer to certified print. 4. Shipping/operating weights indicated are for units without accessories such as sound attenuators, discharge hoods, etc. Consult factory certified prints to obtain weight additions and the heaviest section to be lifted.

5. For indoor applications of evaporative condensers, the room may be used as a plenum with ductwork attached to the discharge only. If inlet ductwork is required, an enclosed fan section must be specified; consult your BAC representative for details. 6. Fan kW is at 0 Pa ESP. To operate against external static pressure up to 125 Pa, increase each fan motor one size. 7. Refrigerant charge listed is R 717 operating charge. To determine operating charge of R22 refrigerants, multiply by: 1,93. For R134A, multiply by: 1,98. 8. Refrigerant connections are standard bevelled for welding.

... because temperature matters

Evaporative Condensers

1. Refrigerant in ND 100; 2. Refrigerant out ND 100; 3. Access; 4. Make-up ND 50; 5. Overflow: ND 80. 6. Drain ND 50; 7. Spray Pump; 8. Fan Motor.

VCL - E 12

Sound Attenuation

VCL

HS Horizontal Intake Sound Attenuation

1.Discharge attenuator, 2. Access Door, 3. Intake Attenuator; W & H = Unit Dimensions (See Engineering Data).

HD Horizontal Intake Sound Attenuation

1.Discharge attenuator, 2. Access Door, 3. Intake Attenuator; W & H = Unit Dimensions (See Engineering Data).

Baltimore Aircoil

VCL - E 13

VS Vertical Intake Sound Attenuation

Dimensions (mm) Model No

VCL 042-079

L2

Maximum Weight (kg) L1

Intake Attenuator

Discharge Attenuator

Total

HS

HD

VS

HS,HD,V S

HS

HD

VS

HS

HD

VS

HS

HD

VS

2390

3125

2010

1820

430

625

548

210

230

192

640

855

740

VCL 084-133

2640

3375

2010

2730

465

660

541

295

315

264

760

975

805

VCL 131-159

2640

3375

2010

3650

465

660

566

365

385

334

830

1045

900

VCL 167-258

2640

3375

2010

2730

665

980

756

465

500

419

1130

1480

1175

VCL 239-321

2640

3375

2010

3650

665

980

761

565

605

529

1230

1585

1290

Note: All units with HS, VS or HD attenuator ship in 2 pieces.

Remote Sump Data Refer to the "Technical Resources" section "Selection of Remote Sump" for Remote Sump Data.

... because temperature matters

Evaporative Condensers

1.Discharge attenuator, 2. Access Door, 3. Intake Attenuator, 4. Plenum; W & H = Unit Dimensions (See Engineering Data).

VCL - E 14

Structural Support REMARK: Do not use for construction. Refer to factory certified dimensions & weights. This brochure includes data

VCL

current at time of publication, which should be reconfirmed at the time of purchase. In the interest of product improvement, specifications, weights and dimensions are subject to change without notice. Up-to-date engineering data and more can be found at www.BaltimoreAircoil.com. The recommended support arrangement for units consists of parallel I-beams running the full length of the unit, spaced as shown in the following drawing. Besides providing adequate support, the steel also serves to raise the unit above any solid foundation to ensure access to the bottom of the unit. To support units in an alternate steel support arrangement, consult your BAC Balticare Representative.

Units with and without Sound Attenuation

1. (4) Ø 22 mm mounting holes; 2. Support Beams; 3. Fan Side; 4. Outline of Unit; 5. Outline of Attenuator “HS” (optional); 6. Outline of Attenuator “HD” (optional).

Model No VCL

A (mm)

B (mm)

Maximum Deflection (mm)

VCL 042-079 VCL 084-119

2426 3334

1194 1194

10 13

VCL 131 VCL 133 VCL 140-159

4253 3334 4253

1194 1194 1194

13 13 13

VCL 167-235 VCL 239-257 VCL 258 VCL 285-321

3334 4253 3334 4253

2344 2344 2344 2344

13 13 13 13

Notes: 1. The recommended support arrangement for these units consists of two parallel I-beams extending the full length of the unit. Supports and anchor bolts are to be designed and furnished by others. 2. All supporting beams are to be flush and level at top and must be oriented relative to gage line as shown. 3. Recommended design loads for each unit support beam should be 70% of the total unit operating weight applied as a uniform load to each of the unit beams. Beams should be designed in

accordance with standard structural practice. For the maximum allowable deflection of beams under the unit refer to above table. 4. All mounting holes have a diameter of 22 mm at the locations shown. 5. If vibration isolators are used, a rail or channel must be provided between the unit and the isolators to provide continuous unit support. Additionally the support beams must be designed to accommodate the overall length and mounting hole location of the isolators that may differ from those of the unit. Refer to vibration isolator drawings for these data.

Baltimore Aircoil

VCL - E 15

Engineering Specifications General A. General: Furnish and install, _____ factory assembled evaporative condenser(s) of counterflow blow-through design, with single side entry, conforming in all aspects to the specifications and schedule as shown on the plans. The condenser shall be of unitary design with all moving parts factory mounted and aligned.

D. Quality Assurance: The manufacture shall have Management System certified by an accredited registrar as complying with the requirements of ISO-9001:2000 to ensure consistent quality of products and services.

Products 1.0 Evaporative Condenser Materials and Components General: All steel panels and structural elements shall be constructed from heavy-gauge, Z600 hot-dip galvanized steel, with cut edges given a protective coating of zinc-rich compound.

2.0 Coil Assembly The heat transfer section shall be integral to the pan section to facilitate rigging and shall include the coil below a spray water distribution system and drift eliminators. 1. The refrigerant condensing coil shall be fabricated of all prime surface steel at the manufacturer’s own facility, and hot-dip galvanized after fabrication. a. The refrigerant condensing coil shall be tested at 34 bar air pressure under water. b. The refrigerant condensing coil shall be designed for low pressure drop with sloping tubes for free drainage of liquid refrigerant. c. The refrigerant condensing coil shall be according to European Pressure Equipment Directive 97/23/EC.

rate sufficient to ensure complete wetting of the coil at all times by large-diameter, non-clog, 360° plastic distribution nozzles spaced across the coil face area in plastic material spray branches. Nozzles shall utilize a two-stage diffusion pattern to provide overlapping, umbrella spray patterns that create multiple intersection points with adjacent nozzles. Spray branches and nozzles shall be held in place by snap-in rubber grommets, allowing quick removal of individual nozzles or complete branches for cleaning or flushing. 3. Removable plastic material drift eliminators shall be positioned to prevent moisture from leaving the evaporative condenser and incorporate a minimum of three (3) changes in air direction.

2. Water shall be distributed evenly over the coil at a minimum flow

3.0 Pan Assembly The evaporative condenser shall include a pan assembly consisting of cold water basin with pump assembly and fan assemblies with single side air inlet. 1. The cold water basin shall include: a drain/clean-out connection; a steel strainer; a brass make-up valve; overflow connection; and a water recirculation pump assembly. a. Drain/cleanout connection shall be located in the cold water basin to allow removal of recirculating water. b. Lift-out steel strainer shall be supplied with perforated openings sized smaller than the water distribution nozzle orifices and an integral anti-vortexing hood to prevent air entrainment. c. Brass make-up valve shall be supplied with a large-diameter plastic float arranged for easy adjustment. d. Overflow connection shall be provided in the cold water basin to protect against recirculating water spillage. e. Water recirculation pump shall be a close-coupled, bronze-fitted centrifugal pump equipped with a mechanical seal, mounted on the basin and piped from the suction strainer to the water distribution system. i. The pump shall be installed so that it may drain freely when the basin is drained. ii. The pump assembly shall include an integral metering valve and bleed line to control the bleed rate from the pump discharge to the overflow connection. iii. The pump motor shall be totally enclosed fan cooled (TEFC) type

suitable for _____ V, ____ phase______ Hz electrical service. f. On installations requiring a remote sump, the evaporative condenser shall be modified to accommodate the use of an independent sump and pump for recirculating water (by others) i. The recirculating water pump, steel strainer, make-up valve, and integral bleed line assemblies shall be omitted from the evaporative condenser scope of supply. ii. The evaporative condenser shall be supplied with a cold water basin outlet sized and located as indicated on the drawings for gravity drain to the remote sump. iii. The water distribution system shall have an operating pressure of 14 kPa at the evaporative condenser spray water inlet connection. 2. Air shall enter the evaporative condenser through the centrifugal fan assemblies. a. Fans and motors shall be located in the dry entering airstream to provide greater reliability and ease of maintenance. b. Fan housings shall have curved inlet rings for efficient air.entry. c. Fan(s) shall be heavy-duty, centrifugal flow type mounted on a steel shaft with heavy-duty, self-aligning, relubricatable bearings with cast iron housings, designed for a minimum L10 life of 40 000 hours. d. Fan motor(s) shall be totally enclosed fan cooled (TEFC) type, suitable for _____ V, ____ phase, ______ Hz electrical service and shall be mounted on an easily adjusted, heavy-duty motor base. Special moisture protection shall be furnished on the windings, shafts, and bearings.

... because temperature matters

Evaporative Condensers

B. Capacity: The evaporative condenser(s) shall be warranted by the manufacturer to have condensing capacity of _____ kW heat rejection, operating with ____ refrigerant and ___ºC condensing temperature and ___ºC entering wet-bulb temperature.

C. Warranty: The manufacturer’s standard equipment warranty shall be for a period of one year from the date of startup or eighteen months from the date of shipment, whichever ends first.

VCL - E 16 4.0 Optional Equipment Specifications A. Evaporative condenser shall be provided with basin heaters to prevent freezing of the water in the cold water basin when the evaporative condenser is idle.

3. Basin heaters shall be provided with a factory-installed low water level cutout switch to prevent heater operation unless the heater elements are fully submerged.

1. The basin heaters shall be selected to maintain +4°C basin water temperature at -18°C ambient temperature.

B. Evaporative condenser shall be supplied with the Baltiguard® Drive System to improve part load efficiency and provide system redundancy in case of a motor failure. 1. The Baltiguard® Drive System shall include the main fan motor as listed in the manufacturer’s published literature and a pony motor sized for approximately 1/3 of design kW and 2/3 of design fan speed to optimize energy savings during non-design load conditions.

VCL

2. Basin heaters shall be electric immersion type controlled by a remote thermostat with the sensing bulb located in the basin water.

5.0 Sound 5.1 Sound Level: To maintain the quality of the local environment, the maximum sound pressure levels (dB) measured 15 m from the

Location

63

125

250

condenser operating at full fan speed shall not exceed the sound levels detailed below.

500

Discharge Air Inlet End Back

Baltimore Aircoil

1000

2000

4000

8000

dB(A)

CXV - E 1

CXV

Evaporative Condensers

CXV Evaporative Condensers ................................................................. E2 Benefits ....................................................................................................... E4 Construction Details CXV Models ........................................................... E6 Construction Details CXV-D Models ....................................................... E7 Custom Features and Options .................................................................. E8 Accessories ............................................................................................... E11 Engineering Data CXV Models .............................................................. E13 Structural Support CXV Models ........................................................... E17 Engineering Data CXV-D Models .......................................................... E18 Structural Support CXV-D Models ....................................................... E20 Engineering Specifications ...................................................................... E21

Evaporative Condensers

Product Detail

CXV - E 2

CXV Evaporative Condensers Capacity

CXV

Single Model Capacity: z

CXV: 410-2730 Nominal R717 kW’s

z

CXV-D: 3500-5140 Nominal R717 kW’s

General Description CXV Evaporative Condensers deliver fully rated thermal performance over a wide range of heat rejection and temperature requirements for various refrigerants. Standard design features directly address today’s environmental concerns by minimizing refrigerant charge and energy consumption. The Series 1500 minimizes installation costs, provides year-round operating reliability, and simplifies maintenance requirements.

Key Features z

Low energy consumption

z

Easy maintenance

z

Reduced refrigerant charge

z

Low installed cost

z

Application flexibility

z

Reliable year-round operation

z

Long service life

z

PED 97/23/ EC coil design

Baltimore Aircoil

CXV - E 3

Evaporative Condensers

... because temperature matters

CXV - E 4

Benefits Low Energy Consumption z

CXV

z

z

Evaporative Cooling Equipment minimizes the energy consumption of the entire system because it provides lower operating temperatures. The owner saves money while conserving natural resources and reducing environmental impact. Evaporative Condensers provide lower condensing temperatures and can offer significant horsepower savings over conventional air-cooled and water-cooled condensing systems. CXV provides heat rejection at the lowest possible energy input and maintenance requirements via: - High efficiency, low kW axial fans - Patented combined flow technology, which reduces evaporation directly off the coil, minimizing the potential for scaling and fouling - Parallel flow of air and spray water, which eliminates scale-promoting dry spots - Multiple Fan Motor System: independent fan motor and drive assembly per fan, which allows for extra steps of capacity control.

Easy Maintenance z

z

z

Access - Hinged access doors provide easy access to the unit interior. In addition, all CXV models are provided with an internal walkway as standard. An internal walkway is available as an option on CXV-D models. Spacious Interior – Provides easy access to the cold water basin, drift eliminators, fan drive system and condensing coil. Access to Spray Distribution – Parallel flow of air and spray water over the coil allows for inspection and access to the top of the coil during full operation.

Large, hinged access door

Baltimore Aircoil

Easy Access to Coil Section

Spray Distribution System

CXV - E 5

Low Installed Cost z

z

z

Support – All models mount directly on parallel I-beams and ship complete with motors and drives factory-installed and aligned. Modular Design – The modular design minimizes the size and weight of the heaviest lift, allowing for the use of smaller, less costly cranes. Coil Connections - Fewer coil connections reduce costs of pipe, valves, purges, and labour.

z

z z

Replacement applications – Single air inlet models are designed to mount directly on existing support steel of both crossflow and counterflow units. Coil configurations – Alternate coil configurations and materials available. Highest capacity in the industry – CXV-D models offer the highest single cell capacity of any evaporative condenser in the industry. Projects benefit from fewer required cells, lower overall fan kW, and fewer piping connections.

Reliable Year-Round Operation z

z

Belt Drive System utilizes special corrosion-resistant materials of construction and state-ofthe-art technology to ensure ease of maintenance and reliable year-round performance. Combined Inlet Shields prevent biological growth from sunlight, act as a filter for air borne impurities and debris and eliminate water splash out.

Easy Removable Fill (for D-models only) The fill removal system allows nesting the fill in place for cleaning and replacement. The fill section can easily be reached after removal of the Combined Inlet Shields / drift eliminators. Telescopic fill support allow for complete fill removal.

Long Service Life z

Materials of Construction – Various materials are available to meet the corrosion resistance, unit operating life, and budgetary requirements of any project.

Note: For more information, please refer to the section “Technical Resources, Materials of Construction”.

Reduced Refrigerant Charge z

z

Combined flow technology provides maximum capacity at the lowest refrigerant charge available in the industry. Reduced refrigerant charge lowers installation costs and may help satisfy refrigerant charge thresholds.

Note: For more information on combined flow technology, refer to section Evaporative Condenser Product Line Overview

1. CXV, 2. Forced Draft; 3. Induced Draft

... because temperature matters

Evaporative Condensers

Application Flexibility

CXV - E 6

Construction Details CXV Models

CXV

.

1. Heavy-Duty Construction z Z600 hot-dip galvanized steel panels 2. Fan Drive System Premium quality belts

z

z

Multiple circuit coils are possible

6. BACross® Wet Deck Surface with Integral Drift Eliminators (Not Shown) z Plastic material

z

Corrosion resistant sheaves

z

Impervious to rot, decay and biological attack

z

Heavy-duty bearings

z

Designed and manufactured by BAC

z

Adapted fan motor for operation in saturated conditions.

7. Combined Inlet Shields z Corrosion Resistant

3. Low kW Axial Fan Quiet operation

z

z

Easily removable UV resistant plastic material

z

High Efficiency

z

z

Corrosion resistant aluminum

8. Cold Water Basin z Sloped cold water basin for easy cleaning

4. Water Distribution System Visible and accessible during operation

z

z

Suction strainer with anti-vortex hood

z

Overlapping spray patterns ensure proper water coverage

z

Adjustable water make-up assembly from air inlet side

z

Large orifice, non-clog nozzles

z

Integral internal walkway as standard

5. Coil Section (Not Shown) Coil according to European Pressure Equipment Directive 97/23/EC, standardized at 23 bar design pressure.

z

z

Continuous serpentine, steel tubing

z

Hot-dip galvanized after fabrication (HDGAF)

z

Pneumatically tested at 34 bar standard coil

z

Sloped tubes for free drainage of fluid

9. Recirculating Spray Water Pump z Close coupled, bronze fitted centrifugal pump z

Totally enclosed fan cooled (TEFC) motor

z

Bleed line with metering valve installed from pump discharge to overflow

10. Hinged Access Doors z Inward swinging door

Baltimore Aircoil

CXV - E 7

Construction Details CXV-D Models .

z

Hot-dip galvanized after fabrication (HDGAF)

z

Pneumatically tested at 34 bar standard coil

2. FRP Casing Panels z Corrosion resistant

z

Sloped tubes for free drainage of fluid

z

Multiple circuit coils are possible

z

UV resistant finish

z

Maintenance free

7. BACross® Wet Deck Surface with Integral Drift Eliminators z Plastic material

3. Fan Drive System z Premium quality belts z

Corrosion resistant sheaves

z

Heavy-duty bearings

z

Adapted fan motor for operation in saturated conditions.

4. Low kW Axial Fan z Quiet operation z

High Efficiency

z

Corrosion resistant aluminum

Designed and manufactured by BAC

8. Combined Inlet Shields Corrosion Resistant

z z

Easily removable

z

UV resistant plastic material

9. Cold Water Basin Sloped cold water basin for easy cleaning

z

Overlapping spray patterns ensure proper water coverage

z

Large orifice, non-clog nozzles

z

Suction strainer with anti-vortex hood

z

Adjustable water make-up assembly from inside the unit

10. Integral Recirculating Spray Water Pumps (Not Shown) Close coupled, bronze fitted centrifugal pump

z

6. Coil Section z Coil according to European Pressure Equipment Directive 97/23/EC, standardized at 23 bar design pressure. Continuous serpentine, steel tubing

Impervious to rot, decay and biological attack

z

z

5. Water Distribution System z Visible and accessible during operation

z

z

z

Totally enclosed fan cooled (TEFC) motor

z

Bleed line with metering valve installed from pump discharge to overflow

11. Hinged Access Doors (Not Shown) Inward swinging door on each end wall

z

... because temperature matters

Evaporative Condensers

1. Heavy-Duty Construction Heavy-gauge Z600 galvanized steel frame

CXV - E 8

Custom Features and Options Construction Options z

CXV

z

Standard Construction: Steel panels and structural elements are constructed of Z600 heavy-gauge hot-dip galvanized steel protected with the Baltiplus Corrosion Protection on the outside of the unit. Optional BALTIBOND® Corrosion Protection System: The BALTIBOND® Corrosion Protection System, a hybrid polymer coating used to extend equipment life, is applied before assembly to all hot-dip galvanized steel components of the unit.

z

Optional Stainless Steel Construction: Steel panels and structural elements are constructed of stainless steel either type 304 or 316.

z

Optional Water-Contact Stainless Steel Cold Water Basin: A cost-effective alternative to an all stainless steel unit. The critical components in the cold water basin and the cold water basin itself are provided in stainless steel. The remaining components are protected with the BALTIBOND® Corrosion Protection System.

Note: See section Technical Resources, Material of Construction for more details on the materials described above.

Coil Configurations Each coil is manufactured according to the European Pressure Equipment Directive (PED) 97/23/EC (For more details, refer to the Evaporative Condenser "Overview" section) BAC condenser coils are standard available at a design pressure of 23 bar, and are pneumatically tested at 34 bar. z

Standard Serpentine Coil: The standard condensing coil is constructed of continuous lengths of all prime surface steel, hot-dip galvanized after fabrication (HDGAF)

z

Optional Stainless Steel Coil: Coils are available in Type 304L and 316L stainless steel for specialized applications.

z

Optional High Pressure Coil: Coils are available with a design pressure of 28 bar, with a test pressure of 40 bars. The Coil is hot-dip galvanised after fabrication (HDGAF).

z

Multiple Refrigerant Circuit Coils (Split Coils): In general, multiple circuit coils are required primarily on halocarbon refrigerant systems where it is common practice to maintain individual compressor systems. Also, a circuit can be isolated to provide cooling of a water or glycol loop for compressor jacket cooling. A wide range of multiple circuit arrangements is available.

All coils are designed for low pressure drop with sloping tubes for free drainage of fluid.

Baltimore Aircoil

CXV - E 9

Multiple Fan Drive System (not on CXV-D models) All CXV-models (except CXV-D) are standard equipped with the multiple fan motor system. This system consists of an independent fan motor and drive assembly per fan with a plenum partition to allow independent operation of each fan. This standard feature provides 2 steps of capacity control on dual fan units and 3 steps of capacity control on triple fan units, as illustrated below.

Extra Steps of Capacity Control

Low Sound Operation The low sound levels generated by Series 1500 Units, thanks to the use of high efficiency low noise fans as standard, make them suitable for installation in most environments. For very sound sensitive installations all models are also available with a “Whisper Quiet” sound fan option that significantly reduces the sound levels generated from the tower with minimal impact on thermal performance. For extremely sound sensitive installations, factory designed, tested and rated sound attenuation is available for both the air inlet and discharge. Note: For more information, please refer to the section “Technical Resources, Sound Reduction Options”.

Gear Drive System, Externally Mounted Motor (CXV-D models only) The D-models are available with a gear drive system with external TEFC motor and a noncorrosive carbon-fiber composite drive shaft with stainless steel hubs is selected with a 2,0 service factor. The motor and drive shaft ship separately for easy field installation.

Gear Drive System, Closed-Coupled Motor (CXV-D models only) The D-Models are available with a close-coupled gear drive system. Both the gear drive and couplings are selected with a 2,0 service factor. Gear construction includes a nickel-alloy steel shaft, casehardened gears, self-lubrication, and a single piece, gray iron housing. This drive system ships completely installed and aligned.

Gear Drive System, close-coupled motor

... because temperature matters

Evaporative Condensers

Individual Motor and Drive on each Fan

CXV - E 10

Combined Inlet Shield Technology Combined Inlet shields prevent biological growth from sunlight, act as a filter for air borne impurities and debris and eliminate water splash out.

CXV

Remote Sump Execution The use of an auxiliary sump within a heated space is the most satisfactory way to protect sump water from freezing. When the circulating pump is shut off, all the water in the water distribution, in suspension and in the sump will drain freely to the auxiliary sump. Note: For detailed information on the calculation of the remote sump tank, please refer to the section "Technical Resources, Selection of Remote Sump Tank".

Combined Inlet Shields

Removable Bundled Fill (only CXVmodels) For installations where it is necessary or recommended to remove the wet deck surface for more thorough cleaning and disinfection, removable bundled fill is available. The fill bundles can be easily lifted and handled by one person and therefore provide a simple and secure method of removing and installing. The bundles can be dismantled and sheet by sheet can be removed for inspection and cleaning of both sides. After cleaning the sheets can be rebundled and re-installed.

Baltimore Aircoil

Easy Removable Fill Bundles

CXV - E 11

Accessories External Service Platform with Ladder, Safety Cage and Handrails

Note: Top air inlet screens are recommended with this option.

Internal Ladder(s) For access to the motor and drive assemblies internal ladders are available on all models. External Service Platform, Ladder and Safety Cage

Internal Service Platforms

For access to the motor and drive assemblies on models CXV-207 through -481, and all CXV-D models, an upper service platform with ladder and handrails is available.

Top Air Inlet Screens The screens protect the air inlet side above the coil section only. Top air inlet screens are always in Baltibond Corrosion® Protection System.

Basin Heaters Units exposed to below freezing ambient temperatures require protection to prevent freezing of the water in the cold water basin when the unit is idle. Factory-installed heaters, which maintain the water temperature at 4°C, are a simple and inexpensive way of providing such protection. The heater package includes the heaters, a thermostat and a low level cut out switch to protect the heaters if the water level is too low. Standard electric heaters are selected for -18°C ambient temperature. Model No. CXV

Heater -18°C (kW)

CXV 074 - 093

1x4

CXV 123 - 147

1x6

CXV 153 - 193

1x6

CXV 207 - 296

1x8

CXV 338 - 435

2x6

CXV 283 - 327

2x6

CXV 416 - 481

2x8

CXV D645 - D792

2 x 12

CXV D791 - D944

2 x 14

Vibration Cut-out Switch A factory-mounted vibration cut-out switch is available to effectively protect against equipment failure due to excessive vibration of the mechanical equipment system. BAC can provide a vibration cut-out switch in an IP65 enclosure to ensure reliable protection.

... because temperature matters

Evaporative Condensers

In the event the owner requires easy access to the top of the unit, the unit can be furnished with a platform and ladders extending from the base of the unit to the platform, as well as safety cages, and handrail packages.

CXV - E 12

Electric Water Level Control Package The electric water level control replaces the standard mechanical make-up valve when a more precise water level control is required. This package consists of a float switch mounted in the basin and a solenoid activated valve in the make-up water line. The valve is slow closing to minimize water hammer.

CXV

Extended Lubrication Lines Extended lubrication lines with grease fittings are available for lubrication of the fan shaft bearings.

Stand-by Pump A factory mounted stand-by pump is available, including non-return valves in each pump piping line. In case of a pump failure, there can be switched over to the stand-by pump, eliminating the unit shut down period as much as possible.

Extended Lubrication Lines

Basin Sweeper Piping Basin sweeper piping provides an effective method of preventing sediment from collecting in the cold water basin of the unit. A complete piping system, including nozzles, is provided in the unit basin for connection to side stream filtration equipment. Note: For more information, please refer to the section "Technical Resources, Filtration".

N2 Filling of the Coil For prolonged shipment periods (ocean freight) or extended storage on site it is recommended to charge the coil(s) with nitrogen.

Basin Sweeper Piping

Mechanical Equipment Removal System (Only on CXV-D Models) The mechanical equipment removal system is a lightweight, easy to install system for removal and installation of fan motor or gearbox. (motors up to 22kW)

Mechanical Equipment Removal System

Baltimore Aircoil

CXV - E 13

Engineering Data CXV Models REMARK: Do not use for construction. Refer to factory certified dimensions & weights. This brochure includes data current at time of publication, which should be reconfirmed at the time of purchase. In the interest of product improvement, specifications, weights and dimensions are subject to change without notice. Up-to-date engineering data and more can be found at www.BaltimoreAircoil.com.

CXV 74 - CXV 193

Model No. CXV

Operating Shipping Heaviest Weight Weight Section (kg) (kg) (kg)

H (mm)

L (mm)

W (mm)

Air Flow (m3/s)

Fan Motor (kW)

Spray Water Pump Motor Flow (kW) (l/s)

R717 Charge (kg)

CXV 74 CXV 80 CXV 84 CXV 89 CXV 93

3400 3410 3420 3590 3600

2350 2360 2370 2520 2530

1440 1450 1460 1600 1610

3980 3980 3980 3980 3980

1861 1861 1861 1861 1861

2385 2385 2385 2385 2385

13,0 14,5 16,0 14,3 15,8

(1x) 4,0 (1x) 5,5 (1x) 7,5 (1x) 5,5 (1x) 7,5

12,0 12,0 12,0 12,0 12,0

(1x) 1,1 (1x) 1,1 (1x) 1,1 (1x) 1,1 (1x) 1,1

30 30 30 38 38

CXV 123 CXV 131 CXV 137 CXV 147

4980 5000 5240 5260

3390 3410 3610 3640

2150 2160 2360 2390

3980 3980 3980 3980

2775 2775 2775 2775

2385 2385 2385 2385

23,4 26,0 23,0 25,6

(2x) 4,0 (2x) 5,5 (2x) 4,0 (2x) 5,5

18,3 18,3 18,3 18,3

(1x) 2,2 (1x) 2,2 (1x) 2,2 (1x) 2,2

46 46 57 57

CXV 153 CXV 164 CXV 173 CXV 184 CXV 193

6290 6310 6320 6650 6660

4150 4180 4190 4480 4490

2590 2610 2620 2910 2920

3980 3980 3980 3980 3980

3690 3690 3690 3690 3690

2385 2385 2385 2385 2385

26,2 29,2 32,3 28,8 31,9

(2x) 4,0 (2x) 5,5 (2x) 7,5 (2x) 5,5 (2x) 7,5

31,5 31,5 31,5 31,5 31,5

(1x) 2,2 (1x) 2,2 (1x) 2,2 (1x) 2,2 (1x) 2,2

61 61 61 76 76

... because temperature matters

Evaporative Condensers

1. Refrigerant in ND 100; 2. Refrigerant out ND 100; 3. Make-up ND 15; 4. Overflow ND 80; 5. Drain ND 50; 6. Access.

CXV - E 14

CXV

CXV 207 - CXV 435

1. Refrigerant in ND 100; 2. Refrigerant out ND 100; 3. Make-up ND 25; 4. Overflow ND 80; 5. Drain ND 50; 6. Access.

Model No. CXV

Operating Shipping Heaviest Weight Weight Section (kg) (kg) (kg)

H (mm)

L (mm)

W (mm)

Air Flow (m3/s)

Fan Motor (kW)

Spray Water Pump Motor Flow (kW) (l/s)

R717 Charge (kg)

CXV 207 CXV 214 CXV 229 CXV 241 CXV 253 CXV 258 CXV 269 CXV 280 CXV 288 CXV 296

6970 6980 7450 7450 7480 7490 7950 7980 7990 8500

4560 4570 4960 4970 5000 5010 5410 5440 5450 5890

2830 2840 3240 3250 3270 3280 3690 3710 3720 4160

4790 4790 4790 4790 4790 4790 4790 4790 4790 4790

3690 3690 3690 3690 3690 3690 3690 3690 3690 3690

2985 2985 2985 2985 2985 2985 2985 2985 2985 2985

41,8 44,7 35,1 38,9 41,3 44,2 38,6 41,0 43,8 43,5

(2x) 9,0 (2x) 11,0 (2x) 5,5 (2x) 7,5 (2x) 9,0 (2x) 11,0 (2x) 7,5 (2x) 9,0 (2x) 11,0 (2x) 11,0

45,1 45,1 45,1 45,1 45,1 45,1 45,1 45,1 45,1 45,1

(1x) 4,0 (1x) 4,0 (1x) 4,0 (1x) 4,0 (1x) 4,0 (1x) 4,0 (1x) 4,0 (1x) 4,0 (1x) 4,0 (1x) 4,0

69 69 91 91 91 91 114 114 114 136

CXV 338 CXV 354 CXV 369 CXV 379 CXV 396 CXV 411 CXV 424 CXV 435

10810 10820 10870 10880 11590 11640 11650 12410

7070 7090 7140 7150 7760 7810 7820 8490

4670 4680 4730 4740 5350 5400 5410 6090

4935 4935 4935 4935 4935 4935 4935 4935

5520 5520 5520 5520 5520 5520 5520 5520

2985 2985 2985 2985 2985 2985 2985 2985

53,1 58,9 62,5 66,9 58,4 62,0 66,3 65,8

(3x) 5,5 (3x) 7,5 (3x) 9,0 (3x) 11,0 (3x) 7,5 (3x) 9,0 (3x) 11,0 (3x) 11,0

56,8 56,8 56,8 56,8 56,8 56,8 56,8 56,8

(1x) 5,5 (1x) 5,5 (1x) 5,5 (1x) 5,5 (1x) 5,5 (1x) 5,5 (1x) 5,5 (1x) 5,5

136 136 136 136 170 170 170 201

Baltimore Aircoil

CXV - E 15

CXV 283- CXV 481

Model No. CXV

Operating Weight (kg)

Shipping Weight (kg)

Heaviest Section (kg)

H (mm)

L (mm)

W (mm)

Air Flow (m3/s)

Fan Motor (kW)

Spray Water Flow (l/s)

Pump Motor (kW)

R717 Charge (kg)

CXV 283 CXV 297 CXV 309 CXV 327

9050 9080 9100 9650

5850 5880 5900 6380

3960 3990 4010 4490

4790 4790 4790 4790

3690 3690 3690 3690

3610 3610 3610 3610

39,4 43,7 46,4 49,0

(2x) 5,5 (2x) 7,5 (2x) 9,0 (2x) 11,0

45,1 45,1 45,1 45,1

(1x) 4,0 (1x) 4,0 (1x) 4,0 (1x) 4,0

123 123 123 146

CXV 416 CXV 437 CXV 454 CXV 468 CXV 481

13230 13270 13320 13330 14150

8400 8440 8490 8500 9220

5750 5790 5840 5850 6570

4935 4935 4935 4935 4935

5520 5520 5520 5520 5520

3610 3610 3610 3610 3610

59,8 66,3 70,5 75,4 74,4

(3x) 5,5 (3x) 7,5 (3x) 9,0 (3x) 11,0 (3x) 11,0

56,8 56,8 56,8 56,8 56,8

(1x) 5,5 (1x) 5,5 (1x) 5,5 (1x) 5,5 (1x) 5,5

182 182 182 182 216

General Notes CXV Models 1. Standard refrigerant in- and outlet connection sizes are ND100. Consult your local BAC Balticare representative for size and location. Refrigerant connections are standard bevelled for welding. 2. Unit height is indicative, for precise value refer to certified print. 3. Shipping/operating weights indicated are for units without accessories such as sound attenuators, discharge hoods, etc. Consult factory certified prints to obtain weight additions and the heaviest section to be lifted. Operating weight shown in the tables is based on total unit weight, weight of refrigerant operating charge and basin filled to overflow level.

4. Refrigerant charge listed is R717 operating charge. To determine operating charge of R22 refrigerants, multiply by: 1,93. For R134A, multiply by: 1,98. 5. The standard right hand arrangement as shown has the horizontal air inlet side on the right when facing the coil connection side. Left hand can be furnished by special order. Water and refrigerant connections are always located on the opposite ends of the unit. 6. All CXV models will be shipped in two sections. 7. Units have standard Low Noise fans. For units with Whisper Quiet fans a “W” is added at the end of the model name.

... because temperature matters

Evaporative Condensers

1. Refrigerant in ND 100; 2. Refrigerant out ND 100; 3. Make-up ND 25; 4. Overflow ND 80; 5. Drain ND 50; 6. Access.

CXV - E 16

CXV

Sound Attenuation CXV Models

1. Intake Attenuator; 2. Discharge Attenuator; Ht = H (unit height) + 735 mm; W = Unit Width, see general Engineering data.

Model No.

Dimensions (mm)

Weight (kg)

CXV

D

Ht

Intake

Discharge

74 - 93

1345

4715

100

140

123 - 147

1345

4715

130

210

153 - 193

1345

4715

175

255

207 - 296

1500

5525

250

270

338 - 435

1500

5665

375

385

283 - 327

2005

5525

250

310

416 - 481

2005

5665

375

440

Remote Sump Data CXV Models Refer to the "Technical Resources" section "Selection of Remote Sump" for Remote Sump Data.

Baltimore Aircoil

CXV - E 17

Structural Support CXV Models REMARK: Do not use for construction. Refer to factory certified dimensions & weights. This brochure includes data current at time of publication, which should be reconfirmed at the time of purchase. In the interest of product improvement, specifications, weights and dimensions are subject to change without notice. Up-to-date engineering data and more can be found at www.BaltimoreAircoil.com. The recommended support arrangement for units consists of parallel I-beams running the full length of the unit, spaced as shown in the following drawing. Besides providing adequate support, the steel also serves to raise the unit above any solid foundation to ensure access to the bottom of the unit. To support units in an alternate steel support arrangement, consult your BAC Balticare Representative.

1. Unit Outline; 2. Air Intake; 3 Mounting Holes; 4. Unit. Dimensions (mm)

Model No. CXV

Max. Deflection (mm)

W

L

A

B

C

No of 20 mm Anchorbolts

CXV 074 - 093

5

2385

1861

2325

-

255

4

CXV 123 - 147

8

2385

2775

2325

-

255

4

CXV 153 - 193

10

2385

3690

2325

-

255

4

CXV 207 - 296

10

2985

3690

2925

-

255

4

CXV 283 - 327

10

3610

3690

3550

-

255

4

CXV 338 - 435

12

2985

5520

2925

2400

270

8

CXV 416 - 481

12

3610

5520

3550

2400

270

8

Notes: 1. The recommended support arrangement for the units consists of parallel I-beams extending the full length of the unit. Supports and anchor bolts are to be designed and furnished by others. 2. All supporting beams are to be flush and level at top and must be oriented relative to gage line as shown. 3. Recommended design loads for each unit support beam should be 70% of the total unit operating weight applied as a uniform load to each of the unit beams. Beams should be designed in accordance with standard structural practice. For the maximum allowable deflection of beams under the unit see table.

4. All mounting holes have a diameter of 22 mm at the locations shown. 5. If vibration isolators are used, a rail or channel must be provided between the unit (and optional attenuator) and the isolators to provide continuous unit support. Additionally the support beams must be designed to accommodate the overall length and mounting hole location of the isolators that may differ from those of the unit. Refer to vibration isolator drawings for these data. 6. All mounting holes have a diameter of 22mm.

... because temperature matters

Evaporative Condensers

Units with and without Sound Attenuation

CXV - E 18

Engineering Data CXV-D Models REMARK: Do not use for construction. Refer to factory certified dimensions & weights. This brochure includes data current at time of publication, which should be reconfirmed at the time of purchase. In the interest of product improvement, specifications, weights and dimensions are subject to change without notice. Up-to-date engineering data and more can be found at www.BaltimoreAircoil.com.

CXV

CXV-D 645L - CXV-D 944L Double Sided Units

1. Refrigerant in ND100; 2. Refrigerant out ND100; 3. Make-Up ND40, Overflow ND80; 5. Drain ND50; 6. Access at both ends. *Actual shipping dimensions. Weight Model No. CXV-D

Dimensions Air flow (m3/s)

Fan Motor (kW)

Water Flow (l/s)

Pump Motor (kW)

R717 Charge (kg)

3498 3498 3498 3498 3498 3498

79,4 87,6 94,6 86,6 93,5 99,5

22 30 37 30 37 45

113,6 113,6 113,6 113,6 113,6 113,6

(2x) 5,5 (2x) 5,5 (2x) 5,5 (2x) 5,5 (2x) 5,5 (2x) 5,5

298 298 298 354 354 354

4184 4184 4184 4184 4184 4184

101,1 109,9 117,0 107,6 114,6 124,7

30 37 45 37 45 55

113,6 113,6 113,6 113,6 113,6 113,6

(2x) 5,5 (2x) 5,5 (2x) 5,5 (2x) 5,5 (2x) 5,5 (2x) 5,5

342 342 342 410 410 410

Shipping (kg)

Operating (kg)

Heaviest Section (kg)

H (mm)

L (mm)

W (mm)

A (mm)

CXV-D645L CXV-D686L CXV-D717L CXV-D729L CXV-D763L CXV-D792L

13100 13175 13180 14435 14440 14540

18945 19015 19020 20380 20380 20480

3650 3650 3650 4280 4280 4280

5665 5665 5665 5665 5665 5665

3632 3632 3632 3632 3632 3632

7328 7328 7328 7328 7328 7328

CXV-D791L CXV-D827L CXV-D857L CXV-D876L CXV-D906L CXV-D944L

15020 15030 15130 16515 16615 16660

22240 22245 22345 23855 23955 24000

4260 4260 4260 5005 5005 5005

5665 5665 5665 5665 5665 5665

4245 4245 4245 4245 4245 4245

8014 8014 8014 8014 8014 8014

General Notes CXV-D Models 1. Standard refrigerant in- and outlet connection sizes are ND100. Consult your local BAC Balticare representative for size and location. Refrigerant connections are standard bevelled for welding. 2. Unit height is indicative, for precise value refer to certified print.

5. Models with fan motor up to 22 kW have belt drive only; models between 22 kW and 45 kW have standard belt drive but gear drive as an option; models with 55 kW have gear drive only. Motorsize for a specific model is indicated by a letter (x) at the end of the model name. Fan type is indicated by a letter (y) at the end of the model name.

3. Shipping/operating weights indicated are for units without accessories such as sound attenuators, discharge hoods, etc. Consult factory certified prints to obtain weight additions and the heaviest section to be lifted. Operating weight shown in the tables is based on total unit weight, weight of refrigerant operating charge and basin filled to overflow level.

6. Models supplied with an optional gear drive may have heights up to 130 mm greater than shown.

4. Refrigerant charge listed is R717 operating charge. To determine operating charge of R22 refrigerants, multiply by: 1,93. For R134A, multiply by: 1,98.

8. The letter “L” at the end of the model number refers to the standard Low Noise fan. “W” refers to the Whisper Quiet fan.

7. All CXV-D models will be shipped in four sections: 1x lower, 1x fan and 2x coil sections. The heaviest section is the coil section. The weight is shown for one coil section only.

Baltimore Aircoil

CXV - E 19

Sound Attenuation CXV-D models

Model No. CXV-D

Dimensions (mm)

Weight (kg)

D

Ht

Both Intake Sides

Discharge

645L - 792L

3510

6477

700

500

791L - 944L

4170

6477

850

600

Remote Sump Data CXV-D models Refer to the "Technical Resources" section "Selection of Remote Sump" for Remote Sump Data.

... because temperature matters

Evaporative Condensers

1. Intake Attenuator; 2. Discharge Attenuator; W = Unit Width, see general Engineering data.

CXV - E 20

Structural Support CXV-D Models REMARK: Do not use for construction. Refer to factory certified dimensions & weights. This brochure includes data current at time of publication, which should be reconfirmed at the time of purchase. In the interest of product improvement, specifications, weights and dimensions are subject to change without notice. Up-to-date engineering data and more can be found at www.BaltimoreAircoil.com.

CXV

Units with and without Sound Attenuation

1. Unit Outline; 2. Air Intake; 3 Mounting Holes

Model CXV-D

Max. Deflection (mm)

645L- 792L 791L - 944L

Dimensions (mm)

No of 20 mm Anchorbolts

A

B

C

12

3558

3570

37

12

12

4171

3913

37

12

Notes: 1. The recommended support arrangement for the units consists of parallel I-beams extending the full length of the unit. Supports and anchor bolts are to be designed and furnished by others. 2. All supporting beams are to be flush and level at top and must be oriented relative to gage line as shown. 3. Recommended design loads for each unit support beam should be 70% of the total unit operating weight applied as a uniform load to each of the unit beams. Beams should be designed in accordance with standard structural practice. For the maximum allowable deflection of beams under the unit see table.

4. All mounting holes have a diameter of 22 mm at the locations shown. 5. If vibration isolators are used, a rail or channel must be provided between the unit (and optional attenuator) and the isolators to provide continuous unit support. Additionally the support beams must be designed to accommodate the overall length and mounting hole location of the isolators that may differ from those of the unit. Refer to vibration isolator drawings for these data.

Baltimore Aircoil

CXV - E 21

Engineering Specifications General

(Alternate) General: Furnish and install, _____ factory assembled evaporative condenser(s) of induced draft design, with dual side air entry and vertical air discharge. Overall dimensions shall not exceed approximately _____ mm x _____ mm, with and overall height not exceeding approximately _____mm. Operating weight shall not

exceed _____ kg. The evaporative condenser shall be Baltimore Aircoil Model ____________. B. Capacity: The evaporative condenser(s) shall be warranted by the manufacturer to have condensing capacity of _____ kW heat rejection, operating with ____ refrigerant at ___ºC condensing temperature and ___ºC entering wet-bulb temperature. C. Warranty: The manufacturer’s standard equipment warranty shall be for a period of one year from the date of startup or eighteen months from the date of shipment, whichever ends first. D. Quality Assurance: The manufacture shall have Management System certified by an accredited registrar as complying with the requirements of ISO-9001:2000 to ensure consistent quality of products and services.

Products 1.0 Evaporative Condenser Materials and Components 1.1 Baltiplus Corrosion Resistant Construction: Unless otherwise noted in this specification, all steel panels and structural elements shall be constructed from heavy-gauge, Z600 hot-dip galvanized steel, with all sheared edges given a protective coating of zinc-rich compound and the exterior protected with the Baltiplus Corrosion Protection.

Corrosion Protection System. The system shall consist of Z600 hot dip galvanised steel prepared in a four-step (clean, pre-treat, rinse and dry) process with an electrostatically sprayed, thermosetting hybrid polymer fuse-bonded to the substrate during a thermally activated curing stage monitored by a 23-step quality assurance program.

(Alternate 1.1) Baltibond® Corrosion Resistant Construction: Unless otherwise noted in this specification, all steel panels and structural members shall be protected with the BALTIBOND®

Or for CXV-D models: General: Casing panels shall be constructed of corrosion resistant, fiberglass, reinforced polyester (FRP).

2.0 Coil Casing Assembly The evaporative condenser shall include a coil casing section consisting of a refrigerant condensing coil, a spray water distribution system, drift eliminators, fan and drive system as indicated by the manufacturer. 2.1. The refrigerant condensing coil shall be fabricated of all prime surface steel at the manufacturer’s own facility, and hot-dip galvanized after fabrication. a. The refrigerant condensing coil shall be according to European Pressure Equipment Directive 97/23/EC, with design pressure of 23 bar. b. The refrigerant condensing coil shall be tested at 34 bar air pressure under water. c. The refrigerant condensing coil shall be designed for low pressure drop with sloping tubes for free drainage of liquid refrigerant. 2.2 Spray Water Distribution System: Water shall be distributed evenly over the coil at a minimum flow rate sufficient to ensure complete wetting of the coil at all times by large-diameter, non-clog, 360° plastic distribution nozzles spaced across the coil face area in spray branches. Nozzles shall utilize a two-stage diffusion pattern to provide overlapping, umbrella spray patterns that create multiple intersection points with adjacent nozzles. a. Nozzles and spray branches shall be observable and accessible for cleaning from the outside of the evaporative condenser during condenser operation without the removal of other components. b. Spray branches and nozzles shall be held in place by snap-in rubber grommets, allowing quick removal of individual nozzles or complete branches for cleaning or flushing. 2.3. Removable drift eliminators shall be positioned to prevent moisture from entering the air plenum and incorporate a minimum of

three (3) changes in air direction. The drift eliminators shall be removable in easy to handle sections for quick access to the coil. 2.4. Fan(s) and Drive System: Fan(s) shall be driven by V-type belts. a. Fan(s) shall be heavy-duty, axial flow low noise, with aluminium alloy blades. Air shall discharge through a fan cylinder designed for streamlined air entry and minimum fan blade tip clearance for maximum fan efficiency. (Alternate a) Fan(s) shall be of “Whisper Quiet” fan design for ultra low sound consisting of: i. multiblade aerofoil fan design constructed of fibreglass reinforced plastic blades (for CXV-D models). ii. specially shaped aluminium blades with end caps and flexible hub connection (for CXV-models). b. Fan(s) and shaft(s) shall be supported by heavy-duty, self-aligning, grease-packed ball bearings with moisture-proof seals and integral slinger rings, designed for a minimum L10 life of 40,000 hours. c. Fan and motor sheaves shall be fabricated from corrosion resistant materials. d. Fan motor(s) shall be totally enclosed fan cooled (TEFC) type, suitable for ____ volt, ____ phase, ___ Hz electrical service and shall be mounted on an easily adjusted, heavy-duty motor base. e. The motor shall be furnished with double-sealed, permanently lubricated bearings and special moisture protection on windings, shafts and bearings. f. Air plenum shall provide a minimum of 1220 mm clearance under the motor base to provide comfortable working space for service personnel. g. Each fan is equipped with an independent motor and drive assembly to allow independent operation of each fan.

3.0 Pan Assembly The evaporative condenser shall include a pan assembly consisting of cold water basin with pump assembly, heat transfer section for spray water cooling with integral drift eliminators, combined inlet shields and hinged access door. 3.1 The cold water basin shall be constructed of heavy-gauge steel panels and structural members either protected by Baltiplus or Baltibond®. Basin shall include a depressed section with drain/

cleanout connection. The basin area under the wet deck surface shall be sloped toward the depressed section to facilitate cleaning. - OR (Alternate 3.1) The cold water basin shall be constructed of heavygauge Type 304 or 316 stainless steel panels and structural members. Basin shall include a depressed section with drain/ cleanout connection. The basin area under the wet deck surface shall

... because temperature matters

Evaporative Condensers

A. General: Furnish and install, _____ factory assembled evaporative condenser(s) of induced draft design, with single side air entry and vertical air discharge. Overall dimensions shall not exceed approximately _____ mm x _____ mm, with an overall height not exceeding approximately _____mm. Operating weight shall not exceed _____ kg. The evaporative condenser shall be Baltimore Aircoil Model ____________.

CXV

CXV - E 22 be sloped toward the depressed section to facilitate cleaning. 3.2 The cold water basin shall include a drain/clean-out connection; a steel strainer; a brass make-up valve; over flow connection; and a water recirculation pump assembly. a. Cold water basin shall be designed so that the strainer, makeup valve and float, and pump assembly are easily accessible without removing any of the unit panels. b. Lift-out steel strainer shall be supplied with perforated openings sized smaller than the water distribution nozzle orifices and an integral anti-vortexing hood to prevent air entrainment. c. Water recirculation pump shall be a close-coupled, bronze-fitted centrifugal pump equipped with a mechanical seal, mounted on the basin and piped from the suction strainer to the water distribution system. i. The pump shall be installed with adequate drains so that it may drain freely when the basin is drained. ii. The pump assembly shall include an integral metering valve and bleed line to control the bleed rate from the pump discharge to the overflow connection. iii. The pump motor shall be totally enclosed fan cooled (TEFC) type suitable for _____ volt, ____ phase, ______ Hz electrical service. d. On installations requiring a remote sump, the evaporative condenser shall be modified to accommodate the use of an independent sump and pump for recirculating water (by others). i. The recirculating water pump, steel strainer, make-up valve, and integral bleed line assemblies shall be omitted from the evaporative condenser scope of supply.

ii. The evaporative condenser shall be supplied with a cold water basin outlet sized and located as indicated on the drawings for gravity drain to the remote sump. iii. The water distribution system shall have a design operating pressure of 14 kPa at the evaporative condenser spray water inlet connection. 3.3 The heat transfer section shall consist of BACross® wet deck surface with integral drift eliminators for CXV and BACrossII wet deck surface with integral drift eliminators for CXV-D for cooling the spray water leaving the coil to optimize the thermal performance of the evaporative condenser. a. The wet deck surface and integral drift eliminators shall be formed from plastic material. b. The wet deck surface and integral drift eliminators shall be impervious to rot, decay, fungus, and biological attack. 3.4 Combined Inlet Shields: Combined inlet shields shall be separate from the wet deck surface and removable to allow easy access for inspection of the air/water interface at the air inlet side of the equipment. Combined inlet shields shall prevent UV-light and debris from entering the unit, as well as prevent water splash out during fan cycling. They shall be constructed of maintenance free, corrosion and UV resistant material. 3.5 Plenum Access: A large, hinged access door shall be provided for access to the coil, drift eliminators and fan plenum section. The water make-up valve, float ball and suction strainer shall be easily accessible.

4.0 Optional Equipment Specifications A. Evaporative condenser shall be provided with basin heaters to prevent freezing of the recirculating water when the evaporative condenser is idle.

Or for CXV-D Models C. Evaporative condenser shall be provided with factory assembled, field installed perimeter safety railings and walking surface above coil air intake to provide access to the top of the evaporative condenser.

1. The basin heaters shall be selected to maintain 4°C basin water temperature at 18°C ambient temperature 16 km/h wind speed. 2. Basin heaters shall be electric immersion type controlled by a remote thermostat with the sensing bulb located in the basin water. 3. Basin heaters shall be provided with a low water level cutout switch to prevent heater operation unless the heater elements are adequately submerged.

D. Evaporative condenser shall be provided with a moveable ladder with fixed ladder supports to provide access to the fan drive system and coil assembly. E. Evaporative condenser shall be provided with an internal walkway at the access door to facilitate servicing the unit. (Standard on S1500 only).

B. Evaporative condenser shall be provided with extended lubrication lines with standard grease fittings for lubricating the fan shaft bearings from the outside base of the condenser.

F. Evaporative condenser shall be provided with a factory assembled internal working platform with ladder to provide a permanent working surface for maintenance personnel (CXV-193 and larger only).

C. Evaporative condenser shall be provided with a factory assembled field-installed external platform with an access ladder and handrails to provide access to the top of the evaporative condenser.

For CXV-D models: G. Evaporative condenser shall be supplied with a right angle gear drive designed specifically for evaporative condenser service. All gears shall have a minimum service factor of 2.0 based on design fan horsepower. An oil level fill port and sight glass shall be located on the gear drive to facilitate routine inspection and maintenance.

1. Optional ladder with safety cage shall be available.

5.0 Sound 5.1 Sound Level: To maintain the quality of the local environment, the maximum sound pressure levels (dB) measured 15 m from the

Location

63

125

250

condenser operating at full fan speed shall not exceed the sound levels detailed below.

500

Discharge Air Inlet End Back (not on D-models)

Baltimore Aircoil

1000

2000

4000

8000

dB(A)

TSU - F 1

TSU

Thermal Storage Products

ICE CHILLER® Thermal Storage Products .......................................... F2 Benefits ........................................................................................................ F4 Proven Technology ..................................................................................... F7 Construction Details TSU-M - Internal Melt Application ..................... F9 Engineering Data TSU-M ........................................................................ F10 Engineering Specifications TSU-M ........................................................ F18 Construction Details TSU-C/D - External Melt Application ............... F19 Engineering Data TSU-C/D ..................................................................... F20 Engineering Specifications TSU-C/D ..................................................... F27 Engineering Considerations ICE CHILLER® Products ..................... F28

Thermal Storage Products

Product Detail

TSU - F 2

ICE CHILLER® Thermal Storage Products

TSU

General Description Cooling with ice thermal storage can be the most cost-effective, reliable system approach to cooling offices, schools, hospitals, malls and other buildings, and provides a steady source of low temperature fluids for process cooling applications. These systems are environmentally friendly because they help lower energy consumption and reduce greenhouse gas emissions. With thousands of successful installations worldwide, BAC is the global leader in the application of ice thermal storage.

Key Features z

Lowest first cost

z

Reduced energy cost

z

Variable capacity

z

Improved system reliability

z

Reduced maintenance

z

Environmentally friendly

z

Proven technology

Baltimore Aircoil

TSU - F 3

Thermal Storage Products

... because temperature matters

TSU - F 4

Benefits

TSU

Lowest First Cost Systems with ice thermal storage can be installed at the same or lower first cost than traditional systems when designed with the colder supply water available from ice. The savings that result from the use of smaller chillers and cooling towers, reduced pump and pipe sizes and less connected horsepower, offset the cost of the ice thermal storage equipment. Additional savings can be found when using lower temperature air distribution, which allows reduced ductwork and fan sizes. z

z

z

Smaller Chillers and Heat Rejection Equipment: By designing the system around 24-hour per day chiller operation, the size of the chillers and cooling towers or air-cooled condensers required for an ice system is significantly reduced, when compared to conventional chillers and heat rejection equipment sized for the instantaneous peak load. A typical thermal storage design includes chillers that provide 50 to 60% of the peak cooling load. The balance of the cooling requirement is provided from the ice storage system. Reduced Pump and Pipe Sizes: Pump and pipe sizes are also reduced in a properly designed ice storage system. Substantial savings in the chilled water distribution loop are realized when the system design incorporates reduced flow rates that result from using a larger temperature range in the water loop. Use of a larger temperature range, for example 10°C instead of the more traditional 5.5°C temperature range results in a reduction of pipe size. Condenser water pipe sizes are reduced due to lower flow requirements for the smaller chiller. Pump savings due to reduced chilled water and condenser water flow rates are also realized.

Reduced Cooling Coil and Supply Air Fan Sizes: Cooling coils sized using lower supply water temperatures and traditional supply air temperatures are generally smaller due to fewer rows. The reduction in rows leads to lower supply fan kW.

Baltimore Aircoil

TSU - F 5

z

z

z

Reduced Air Handling Equipment: When the air distribution is designed with lower supply air temperatures, the size of the ductwork, fans and fan motors are reduced. Reduced Electrical Distribution: Smaller chillers, heat rejection equipment and pumps require less horsepower than a traditional system, which results in smaller transformers, switchgear, wire sizes and starter panels.

Reduced Energy Cost An ice thermal storage system reduces peak demand, shifts energy usage to non-peak hours, saves energy, and reduces energy costs. z

z

Reduces Peak Demand and Shifts Energy Usage: With less connected horsepower, ice storage can lower peak electrical demand for the HVAC or process cooling system by 50% or more. Since most electrical rates include demand charges during peak demand times and/or higher day versus night kWh charges, savings on electrical bills can be substantial. In areas with “real time pricing”, where the electric rate varies hour by hour based on the market price of electricity, day to night kWh costs can vary by 500 to 1000%. The use of electricity at night versus peak daytime hours can lead to large savings on energy bills. Saves Energy: In addition, total annual kilowatt-hours used are less when the system is designed taking advantage of the low supply water temperature available from the ice storage system. Lower kWh consumption is possible for five reasons:

1. Although making ice requires more energy than producing chilled water, the efficiency penalty is not as large since the ice is made at night when condensing temperatures are lower, increasing the efficiency of the chiller. 2. Ice systems typically operate the chiller at full load. Chillers are inefficient when run with low loads during the spring and fall. A typical chiller will operate at less than 30% capacity for half the year. 3. Reduced pumping horsepower. 4. Reduced fan horsepower due to lower air pressure drop across the cooling coil. A higher chilled water temperature differential across the cooling coil usually results in fewer rows and therefore a lower pressure drop. 5. The ability to recover waste heat from the chiller for heating water both night and day. Additional kWh savings are possible if the air distribution is designed to take advantage of the low temperatures available from the ice storage system. As the electric industry continues to deregulate, and time-of-use rates, real time pricing schedules and negotiated power prices become standard, ice storage can provide even greater future savings in operating costs.

... because temperature matters

Thermal Storage Products

Reduced Generator Size: If a facility has a generator for daily or back-up power, the size of the generator will be significantly reduced when the peak electrical load of the facility is reduced using ice storage.

TSU - F 6

Variable Capacity The ice thermal storage system will maintain a constant supply temperature regardless of the variations in instantaneous cooling demand. The flow and entering water temperature set the instantaneous capacity.

TSU

Improved System Reliability Ice storage systems provide the reliability necessary to ensure air-conditioning is available. With traditional systems, installing multiple chillers provides redundancy. In the event of a mechanical failure of one chiller, the second chiller provides limited cooling capacity. The maximum available cooling for the traditional system would only be 50% on a design day. Most ice storage systems utilize two chillers in addition to the ice storage equipment. Two chillers are designed to provide approximately 60% of the required cooling on a design day while the ice storage provides the remaining 40% of the cooling capacity. In the event only one chiller is available to provide cooling during the day, up to 70% of the cooling capacity is available. The one operable chiller provides 30% of the cooling requirement while the ice provides up to 40%. Based on typical HVAC load profiles and ASHRAE weather data, 70% of the cooling capacity would meet the total daily cooling requirements 85% of the time.

Reduced Maintenance The ice thermal storage coils have no moving parts so very little maintenance is required. Because the chillers, pumps and heat rejection equipment are smaller, ice storage systems will have less maintenance than a traditional system. The ice thermal storage system also allows a chiller to undergo routine maintenance during the day when the ice storage can handle the system load.

Environmentally Friendly Reducing energy consumption and using electricity at night will reduce global warming. Electricity generated at night generally has a lower heat rate (lower fuel use per power output), and therefore lower carbon dioxide and greenhouse gas emissions resulting in less global warming. The California Energy Commission concluded that the use of electricity at night created a 31% reduction in air emissions over the use of electricity during the day. With smaller chillers, an ice thermal storage system reduces the amount of refrigerant in a system. Most refrigerants in use today are slated to be banned in the future under the Montreal Protocol because they contribute to global warming. Using smaller amounts of refrigerant helps to save the ozone and reduce global warming.

Baltimore Aircoil

TSU - F 7

Proven Technology BAC has successfully applied ice thermal storage technology to thousands of installations worldwide. BAC has the application and system experience to assist you in the design, installation and operation of your ice storage system. B.A.C. has supplied ICE CHILLER® Thermal Storage Products for projects that range in size from 90 to 125,000 ton-hours (0,3 to 441,3 MWh). Installations include office buildings, hospitals, manufacturing processes, schools, universities, sports arenas, produce storage facilities, hotels and district cooling applications.

The BAC product offering provides system design flexibility. Ice can be built using ammonia or various glycols on steel coils and is used to provide either chilled water or glycol to the cooling system. This flexibility, combined with a broad range of application experiences, allows B.A.C. to provide a cost-effective product to meet your specific requirements.

CNES - Toulouse (France) The cooling plant of the Centre Nationale d’Etudes Spatiales (CNES) in Toulouse, incorporated 3 centrifugal chillers, each 3 MW cooling capacity. As the facilities grew in size over the years, the plant became short of capacity on peak cooling load days. Rather than adding another chiller to increase the maximum cooling capacity, CNES wanted a more energy and cost efficient solution. An 11 MWh Ice Thermal Storage System, proved to be the most economical. During daytime the chillers run continuously at maximum capacity and thus at highest efficiency. At night ice is built to take advantage of the lower off-peak electricity costs.

CNES

CSELT - Turin (Italy) Designing a high quality and reliable climate control system with a low first cost and a low operating cost for the new CSELT (Centro SIP Elaborazione Telecomunicazioni) Research Centre was an ambitious goal. This requirement however was fully met by using standard glycol chillers with a 13 MWh BAC Thermal Storage System. During the night ice is built to provide part of the cooling capacity for the next day. In the daytime the water from the cooling load is first cooled by the chillers and then further cooled to the design temperature by the BAC Thermal CSELT Storage System. This series arrangement, with the chiller upstream in the most favourable position, is only possible due to the high melt off capacity offered by the BAC ICE CHILLER® which guarantees a constant low leaving water temperature from the Thermal Storage System.

... because temperature matters

Thermal Storage Products

The ICE CHILLER® Product line includes a variety of factory-assembled units. For large applications, where space is limited or factory-assembled units are not cost effective, ICE CHILLER® Thermal Storage Coils are available for installation in field-erected tanks.

TSU - F 8

TSU

Academic Hospital - Groningen (Netherlands) The cooling for the HVAC system in the new Academic Hospital in Groningen is provided by a standard 650 kW glycol chiller and a 6 MWh BAC ICE CHILLER® Thermal Storage System. The system design makes full use of the low leaving water temperatures available from the ICE CHILLER® Thermal Storage System by placing the chiller upstream and in series with the ICE CHILLER®. This provides the most economical solution, an overall low energy cost and a great flexibility in the cooling plant operation.

Academic Hospital

KBC - Leuven (Belgium) This new 90.000 m2 building for the KBC bank headquarter has a total daily cooling load of 26 MWh with a peak of 3 MW. The HVAC system selected by the owner included a Thermal Storage System because of its low first cost, economical operating cost and high system reliability. A 1 MW chiller combined with a 10 MWh BAC Thermal Storage System can easily satisfy the 3MW peak cooling load. Energy costs are lower than with a conventional system because electrical demand charges and expensive day rates are reduced to a minimum.

KBC Bank

Granada Centre - Riyadh (Saudi Arabia) The designers of the Granada Centre in Riyadh, Saudi Arabia were confronted with a limited electrical power supply to the new site. This forced the client to consider all possible load shifting alternatives. After careful review of the available options it was decided to limit the power demand of the chillers and shift the generation of cooling to off-peak periods. From the maximum cooling demand, being 14.250 kW, about 8.000 kW is delivered directly by the chillers. The remaining cooling will come from the ice storage units. The ice storage plant includes 22 ice storage tanks model TSU 761 M with a total ice storage capacity of 58.800 kWh.

Baltimore Aircoil

Granada Centre

TSU - F 9

Construction Details TSU-M - Internal Melt Application

z 48-hour integrity test before shipment

z Watertight

6. Extruded Polystyrene Insulation

z Heavy-gauge Z600 Hot-dip galvanized steel panels

z 110 mm of total insulation

z Insulated with 50 mm extruded polystyrene insulation

z 20 mm of insulation between primary and secondary liner

2. Coil Support Beams

z Contributes to total insulating value of 3,1m°C/W

z Prevent contact between coil and primary liner

7. Secondary Liner/Vapor Barrier

3. Glycol Connections

z Prevents moisture from penetrating through the insulation

z Threaded connections

8. Wall Panel

z Flanged connections (optional)

z Heavy-gauge glavanised steel with double brake flanges

4. Galvanised Steel Coil

z Extruded polystyrene insulation

z Hot-dip galvanized after fabrication (HDGAF)

z Contributes to total insulating value of 3,1m°C/W

z Steel tubing, encased in a steel framework

9. Sight Tube

z Pneumatically tested at 13 bar

z Visual indicator of the amount of ice remaining in unit

z Rated for 10 bar operating pressure

10. Ice Inventory Sensor (Optional) - Not Shown

5. Primary Liner

z Mechanical Water Level Difference Transmitter provides an

z Single piece

electrical 4-20 mA output signal which is proportional to the amount of ice in inventory

... because temperature matters

Thermal Storage Products

1. Covers

TSU - F 10

Engineering Data TSU-M TSU-M & TSU-LM Units

TSU

REMARK: Do not use for construction. Refer to factory certified dimensions & weights. This brochure includes data current at time of publication, which should be reconfirmed at the time of purchase. In the interest of product improvement, specifications, weights and dimensions are subject to change without notice. Up-to-date engineering data and more can be found at www.BaltimoreAircoil.com.

1. Outlet; 2. Inlet; 3. Sight Tube; 4. Access Hatch.

Model TSU-M

Latent Capacity (kWh)

Approx. Sh. Weight (kg)

Approx. Op. Weight (kg)

Tank Water Coil Glycol Connection Volume Volume Size ND (l) (l) (mm)

Unit Width (mm)

Unit Length (mm)

Unit Height (mm) H1

Tank Height (mm) H2

TSU-237M

834

4420

17730

11320

985

50

2400

3240

2440

2390

TSU-476M

1674

7590

33530

22110

1875

80

2400

6050

2440

2390

TSU-594M

2087

9150

42200

28250

2320

80

2980

6050

2440

2390

TSU-761M

2676

10990

51610

34640

2990

80

3600

6050

2440

2390

Model TSU-LM

Latent Capacity (kWh)

Approx. Sh. Weight (kg)

Approx. Op. Weight (kg)

Unit Width (mm)

Unit Length (mm)

Unit Height (mm) H1

Tank Height (mm) H2

TSU-L184M

647

3760

14360

8820

770

50

2400

3240

2000

1950

TSU-L370M

1301

6400

27060

17250

1460

80

2400

6050

2000

1950

TSU-L462M

1625

7710

34030

22030

1810

80

2980

6050

2000

1950

TSU-L592M

2082

9200

41560

27020

2280

80

3600

6050

2000

1950

Tank Water Coil Glycol Connection Volume Volume Size ND (l) (l) (mm)

General Notes 1. All dimensions are in mm. Weights are in kg.

3. All connections are threaded

2. Unit should be continuously supported on a flat level surface.

4. H1, H2 = installed height. Coils are capped for shipping and storage. Add 75 mm for shipping height.

Baltimore Aircoil

TSU - F 11

Custom Coils for Internal Melt Application (TSU-M)

BAC can predict the temperatures required on an hour by hour basis for building ice on custom Installation of Coil Module coils, over a variety of conditions and build times. The physical space available, load profile, discharge temperatures, chiller capacity and operating sequences can be evaluated to find the design that best meets the application. The ICE CHILLER® Thermal Storage Coils are constructed of continuous 26,7 mm O.D. all prime surface serpentine steel tubing. The coils are assembled in a structural steel frame designed to support the weight of the coil stack with a full ice build. After fabrication the coils are tested for leaks using 13 bar air pressure under water, then hot-dip galvanized for corrosion protection. The coils are configured to provide countercurrent glycol flow in adjacent circuits for maximum storage capacity. Individual coils can be factory-assembled into modules of two (2) coils for optimization of transport cost and reduction of site assembly time. Glycol manifolds are coated with zinc-rich, cold galvanizing finish at the factory. Necessary support steel and lifting lugs are provided on the modules to allow for lifting into and final positioning within the storage tank.

Load Profile A daily load profile is the hour–by–hour representation of cooling loads for a 24–hour period. Most HVAC applications use a daily load profile to determine the amount of storage required. Some HVAC systems apply a weekly load profile. For conventional air–conditioning systems, chillers are selected based on the peak cooling load. For ice storage systems, the chillers are selected based on the kWh of cooling required and a defined operating strategy. Typical HVAC Load Profile Thermal storage systems provide much flexibility for varying operating strategies as long as the total kWh selected are not exceeded. This is why an accurate load profile must be provided when designing an ice storage system. Load profiles take many different shapes based on the application. The figure above illustrates a typical HVAC load profile for an office building with a 1750 kW peak cooling load and a 12–hour cooling requirement. The shape of this curve is representative of most HVAC applications. For preliminary equipment selections, BAC's ICE CHILLER® Thermal Storage Unit Selection Program can generate a similar load profile. Information required is the estimated building peak cooling load and duration of the cooling load.

... because temperature matters

Thermal Storage Products

BAC will manufacture custom ICE CHILLER® Thermal Storage Coils to meet project specific requirements. BAC has done extensive research and testing on the build and melt characteristics of ice storage. This research and testing has resulted in selection capabilities unmatched by any other company in the industry.

TSU - F 12

The Air–Conditioning & Refrigeration Institute (ARI) has published Guideline T, "Specifying the Thermal Performance of Cool Storage Equipment." The purpose of Guideline T is to establish the minimum user specified data and supplier specified performance data. Design data provided by the engineer includes: System Loads, Flow Rates and Temperatures.

Operating Strategies

TSU

Once the load profile is generated, the next step in selecting Thermal Storage equipment is to define an operating strategy or in other words, determine the hours per day during which the glycol chiller is allowed to operate. Which operating strategy to use is dependent upon the load profile (application), the utility rate structure, the energy cost and the equipment first cost. In other words, the economical balance between the system installation and operating cost or the payback period must be calculated. There are 2 different operating strategies, either full or partial storage. Full Storage Systems store all the cooling capacity required during the off peak periods and eliminate the need to operate the chiller(s) during the utility on-peak period. This strategy shifts the largest amount of electrical demand and results in the lowest operating cost. However, the equipment first cost is considerably higher than partial storage systems due to larger chiller and storage requirement and full storage is therefore seldom used. Partial Storage Systems require that the chiller(s) operate also during the on-peak period. The partial storage system allowing the glycol chiller to run for 24 hours per day at its full capacity is most commonly used as it results in the smallest chiller selection. In many cases, the smaller chiller selection is the driving force for an ice storage system because of lower installed electrical kW, smaller refrigerant charge, smaller cooling towers or other heat rejection equipment (lower noise), smaller standby chillers (if required), lower capital and maintenance cost, ... Other partial storage operating strategies stop the chiller a few hours per day when electricity cost are high and/or where non-cooling electricity usage are important (so when the chiller operation would increase the electrical demand). It is however important to know that the more hours the chiller is stopped during the day, the larger its size will be. Furthermore, if the chiller is stopped during the cooling period, the size of the storage equipment needs to be increased. If the chiller is stopped during the non-cooling period, the ice build time is reduced and therefore lower glycol temperatures are required and the chiller COP is reduced. Besides determining when the chiller should run or be stopped, an other aspect of operating strategy is if during melt-out, priority is given to the chiller or to the ice to cover the presented cooling load. In a chiller priority system the chiller always operates at full capacity. When the cooling load exceeds the chiller performance, the excess is covered by the melting ice. A constant portion of the load is covered by the chiller while the variation in load is covered by the ice. In an ice priority system, a constant part of the load is covered by the ice, where the variation in load is taken by the chiller. Because the chiller does not continuously operate at its maximum capacity, it will be oversized versus the chiller priority system. Ice priority systems result in oversized ice and chiller selections and are therefore seldom used. Normal practice is that partial storage systems using chiller priority with 24h chiller operation are most commonly used.

Baltimore Aircoil

TSU - F 13

Modes of Operation The modular ICE CHILLER® Thermal Storage Unit can operate in any of five distinct operating modes. These modes of operation provide the flexibility required by building operators to meet their daily HVAC cooling requirements.

Ice Build with Cooling: When cooling loads exist during the ice build period, some of the cold ethylene glycol used to build ice is diverted to the cooling load to provide the required cooling. The amount of glycol diverted is determined by the building loop set point temperature. BAC recommends that this mode of operation be applied on systems using primary/secondary pumping (See further for system schematic). This reduces the possibility of damaging the cooling coil or heat exchanger by pumping cold glycol, lower than 0°C, to this equipment. Cooling – Ice only: In this operating mode the chiller is off. The warm return ethylene glycol solution iscooled to the desired set point temperature by melting ice stored in the modular ICE CHILLER® Thermal Storage Unit. Cooling – Chiller only: In this operating mode the chiller supplies all the building cooling requirements. Glycol flow is diverted around the thermal storage equipment to allow the cold supply glycol to flow directly to the cooling load. Temperature set points are maintained by the chiller. Cooling – Ice with Chiller: In this operating mode, cooling is provided by the combined operation of the chiller and thermal storage equipment. The glycol chiller pre-cools the warm return glycol. The partially cooled glycol solution then passes through the ICE CHILLER® Thermal Storage Unit where it is cooled by the ice to the design temperature.

... because temperature matters

Thermal Storage Products

Ice Build: In this operating mode, ice is built by circulating a 25% solution (by weight) of inhibited ethylene glycol at negative temperatures through the coils contained in the ICE CHILLER® Thermal Storage Unit. During this operating mode, the chiller's operating conditions are monitored and the chiller is turned off when the minimum supply glycol temperature off the chiller is reached. Optionally, the ICE LOGIC Ice Quantity Meter is available to control the chiller operation. The figure illustrates typical chiller supply Chiller Supply Temperatures temperatures for 8, 10 and 12 hour build cycles. For a typical 10–hour build time, the supply glycol temperature is never lower than -5,5°C. As the graph illustrates, for build times exceeding 10 hours, the minimum glycol temperature is greater than -5,5°C. For build times less than 10 hours, the minimum glycol temperature will be lower than -5,5°C at the end of the build cycle. This performance is based on a chiller flow rate associated with a 3°C range. When a larger temperature range is the basis of the chiller selection, the chiller supply temperatures will be lower than shown in the figure above.

TSU - F 14

TSU

System Schematics Two basic flow schematics are applied to select ICE CHILLER® Thermal Storage Units. The figure illustrates a single piping loop with the chiller installed upstream of the thermal storage equipment. This design allows the thermal storage system to operate in four of the five possible operating modes. They are Ice Build, Cooling-Ice Only, Cooling-Chiller Only and Cooling–Ice with Chiller. Single loop – Chiller Upstream

For this figure the following control logic is applied: MODE

CHILLER

P-1

V-1

V-2

Ice Build

On

On

A-B

C-B

Cooling – Ice Only

Off

On

Modulate

A-B

Cooling – Chiller Only

On

On

C-B

A-B

Cooling – Ice with Chiller

On

On

Modulate

A-B

Valve V-1 modulates in response to temperature sensor, TS-1. Valve V-2 could be positioned to either maintain a constant flow, less than P-1, or modulate in response to the return glycol temperature from the cooling load. When the building loop contains chilled water, a heat exchanger must be installed to separate the glycol loop from the building’s chilled water loop. On applications where an existing water chiller is available, it can be installed in the chilled water loop to reduce the load on the thermal storage system. This design should not be used when there is a requirement to build ice and provide cooling. This would require the cold return glycol from the thermal storage equipment be pumped to the cooling load or heat exchanger. Since the glycol temperature is below 0°C, the cooling coil or heat exchanger is subject to freezing. The flow schematic illustrated in the figure details a primary/ secondary pumping loop with the chiller located upstream of the thermal storage equipment. This design allows the system to operate in all five operating modes. For this figure the following control logic is applied: MODE

CHILLER

P-1

P-2

V-1

V-2

Ice Build

On

On

Off

A-B

A-C

Ice Build with Cooling

On

On

On

A-B

Modulate

Cooling - Chiller Only

On

On

On

C-B

A-B

Cooling – Ice Only

Off

On

On

Modulate

A-B

Cooling – Ice with Chiller

On

On

On

Modulate

A-B

Baltimore Aircoil

TSU - F 15

As in the single loop schematic, a heat exchanger and a base water chiller can be added to the system schematic. Variations to these schematics are possible but these are the most common for thermal storage systems. One common variation positions the chiller downstream of the thermal storage equipment. This design is used when the glycol temperatures off the ice cannot be maintained for the entire cooling period. By positioning the chiller downstream of the ice, the chiller is used to maintain the required supply temperature. In both of the above figures, the chiller is installed upstream of the ice. This offers two significant advantages compared to system designs that locate the chiller downstream of the ice. First, the chiller operates at higher glycol temperatures to precool the return glycol. This enables the chiller to operate at a higher capacity, which reduces the amount of ice required. Second, since the chiller is operating at higher evaporator temperatures, the efficiency of the chiller is improved.

... because temperature matters

Thermal Storage Products

Valve V-1 and Valve V-2 modulate, depending on the operating mode, in response to temperature sensor, TS-1. The benefit provided by the primary/secondary pumping loop is that the system can build ice and provide cooling without fear of freezing a cooling coil or heat exchanger. This system design also allows for different flow rates in each of the pumping loops. When the flow rates in the pumping loops are different, the glycol flow rate in the primary loop should be greater than or equal to the glycol flow rate in the secondary loop. If not, colder supply glycol Primary/Secondary Pumping Loop – Chiller temperatures from the primary loop are needed to Upstream guarantee the design TS-1 set point (because there is always a mix with warm return glycol from the secondary loop. This reduces the chiller COP. At very large flow rate differences, negative glycol temperatures out of the TSU would be needed to obtain TS-1 (which is impossible)

TSU - F 16

Chiller Performance

TSU

Most packaged chillers can provide a wide range of glycol discharge temperatures and are suited for thermal storage applications. Chiller types applied to thermal storage applications include reciprocating, rotary screw and centrifugal. The chiller type used depends on capacity, glycol discharge temperature, efficiency, condenser type, and refrigerant. Chiller capacity and glycol discharge temperature must be evaluated when designing a thermal storage system. Different glycol discharge temperatures are required for various operating modes that affect the chiller capacity. The chiller capacity provided at -5,5°C is considerably less than the chiller capacity with a 6°C glycol discharge temperature. Chillers selected for use with the BAC's ICE CHILLER® Thermal Storage Units should be able to provide -5,5°C glycol when applied to a 10-hour build cycle. Longer build times result in higher glycol temperatures at the end of the build period while shorter build times require the chiller to supply glycol colder than -5,5°C. The chiller capacity required could limit the use of a specific chiller type on small applications. The nominal capacity range for each chiller type is shown in the table below.

Chiller Type

Nominal Capacity (kW) Range

Reciprocating

50 – 850 kW

Rotary Screw

450 – 4200 kW

Centrifugal

600 – 7000 kW+

Centrifugal and rotary screw chillers have the highest efficiencies with COP’s from 5,9 to 4,7 at 6°C chiller discharge temperature and 4,0 to 3,2 when providing -5,5°C glycol. Reciprocating chillers are less efficient and have COP’s ranging from 4,1 to 3,2 when providing 6°C glycol and 3,2 to 2,7 when making ice at -5,5°C. The heat rejection function of an ice storage system can be handled by any of three types of refrigerant condensers: air–cooled, water-cooled or evaporative. An air–cooled condenser removes heat from the refrigerant and condenses it by forcing air over an extended surface coil through which the refrigerant vapour is circulated. The latent heat of the refrigerant is removed by sensibly heating the air. The condenser capacity is determined by the ambient dry bulb temperature. A water-cooled condenser with a cooling tower rejects heat from a refrigeration system in two steps. First, the refrigerant is condensed by the water flow in the condenser. Second, heat is rejected to the atmosphere as the condenser water is cooled by a cooling tower. The evaporative condenser combines a water–cooled condenser and cooling tower in one piece of equipment. It eliminates the sensible heat transfer step of the condenser water. This allows a condensing temperature substantially closer to the design wet–bulb temperature. Variations in condensing temperatures should be considered when evaluating chiller performance. Reduced night-time ambient dry bulb and wet bulb temperatures offer lower condensing temperatures which help offset the reduction in chiller capacity and chiller efficiency.

Baltimore Aircoil

TSU - F 17

The percent of nominal chiller capacity at various glycol discharge temperatures are shown below.

Glycol Discharge Temperature

Percent of Nominal Capacity*

6,0 °C

97 %

2,0 °C

85 %

-5,5 °C

66 %

Note: * Nominal capacity of the chiller is based on cooling water to 6oC.

z

30°C condenser water or 46°C condensing temperature for cooling operation

z

26,5°C condenser water or 40,5°C condensing temperature for ice build operation

The refrigerant types for chillers also vary. Centrifugal chillers are available for use with R-134a, R-123 and R-22. Reciprocating and rotary screw chillers are available for use with R–134a, R-22 and R-717 (ammonia).

... because temperature matters

Thermal Storage Products

Nominal capacity ratings are based on:

TSU - F 18

Engineering Specifications TSU-M 1.0 ICE CHILLER® Thermal Storage Unit

TSU

1.1 General: The ICE CHILLER® Thermal Storage Unit shall be Baltimore Aircoil Model TSU-______. Overall unit dimensions shall not exceed approximately _____ m by ____ m with an overall height not exceeding ____ m. The operating weight shall not exceed _______ kg 1.2 Thermal Capacity: Each unit shall have a latent kWh storage capacity of _______ kWh to be generated in ____ hours when supplied with _______ l/s of a 25% (by weight) solution of industrially inhibited ethylene/propylene glycol. The minimum glycol temperature

required during the ice build operating mode shall be _______ °C. Rated system performance shall be provided in the format recommended by the Air-Conditioning & Refrigeration Institute (ARI) Guideline T. The thermal storage units shall be modular in design. Unit design shall allow units of different sizes to be installed in order to optimize unit selection and minimize space requirements. Tanks sizes can be mixed due to internal piping arrangements that create a balanced flow due to uniform pressure drop through the coil circuits.

2.0 Construction Details 2.1 Tank: The tank shall be constructed of heavy-gauge Z600 galvanized steel panels and include double brake flanges for structural strength. The tank walls shall be supplied with a minimum of 110 mm of insulation that provides a total insulating value of 3,1 m °C/W. The tank design shall utilize two liners. The 1,5 mm E.P.D.M. liners shall be of single piece construction and be suitable for low temperature applications. Liners shall be separated from each other by 20 mm of extruded polystyrene insulation. The tank bottom shall be insulated with 70 mm extruded, polystyrene insulation. 2.2 Covers: The ICE CHILLER® Thermal Storage Unit shall be provided with watertight, sectional covers constructed of Z600 hot-dip galvanized steel. The covers shall be insulated with a minimum of 50 mm of extruded polystyrene insulation. 2.3 Heat Transfer Section: Contained within the tank shall be a steel heat exchanger that is constructed of 26,7 mm O.D., all prime surface serpentine steel tubing encased in a steel framework. The coil, which is hot-dip galvanized after fabrication, shall be tested at 1300 kPa air

pressure under water and rated for 1000 kPa operating pressure. The coil circuits are configured to provide maximum storage capacity. Each unit shall be supplied with threaded connections. 2.4 Sight Tube: Each ICE CHILLER® Thermal Storage Unit shall be provided with a sight tube mounted on the end of each unit. . The sight tube, which shall be fabricated from clear plastic pipe, displays the tank water level and corresponding ice inventory. Optionally, the exclusive BAC ICE LOGIC Ice Quantity Controller is available for both manual and automatic chiller control. 2.5 Heat Transfer Fluid System: The heat transfer fluid shall be an industrially inhibited, 25% by weight, ethylene glycol solution specifically designed for HVAC applications. The 25% (by weight) solution is designed to provide freeze/burst and corrosion protection as well as efficient heat transfer in water based, closed loop systems. Corrosion inhibitors shall be provided to keep pipes free of corrosion without fouling.

Baltimore Aircoil

TSU - F 19

Construction Details TSU-C/D External Melt Application

5. Covers

The tank is constructed of heavy-gauge, Z600 hot-dip galvnised steel, reinforced with full-length structural steel angles beneath and on all four sides. All seams are welded to ensure watertight construction. A zinc rich coating is applied to all exposed edges and welds.

Sectional insulated tank covers are proided with BAC’s exclusive BALTIBOND® Corrosion Protection System.

6. Galvanised Steel Coil z

Hot-dip galvanised after fabrication (HDGAF)

z

Steel tubing encased in a steel framework

z

Pneumatically tested at 15 bar (31bar) for glycol (ammonia) applications

z

Rated for 10 bar (22 bar) operating pressure

2. Insulation Extruded polystyrene insulation is provided between the tank and the exterior panels. The insulation is 80 mm thick on the tank sides and ends, and 50 mm thick on the bottom and inside the covers

3. Exterior Panels Exterior panels sealed at all seams provide a complete vapor barrier and protect the insulation. They are furnished with BAC’s exclusive BALTIBOND® Corrosion Protection System.

4. Air Pump Centrifugal regenerative blower for field mounting to supply low pressure air for agitation of the water. Pump is complete with a weather protected inlet air filter and is suitable for outdoor applications.

7. ICE-LOGIC Ice Thickness Controller (Not Shown) An electronic, multi-point ice thickness control is mounted on the unit. A control relay is provided to deactivate the refrigeration system when a full build of ice is reached.

8. Air Distribution Low pressure air from the air pump is distributed below the coils through multiple perforated PVC pipes.

... because temperature matters

Thermal Storage Products

1. Tank

TSU - F 20

Engineering Data TSU-C/D TSU-95C - TSU-225C & TSU-185C - TSU-450C

TSU

REMARK: Do not use for construction. Refer to factory certified dimensions & weights. This brochure includes data current at time of publication, which should be reconfirmed at the time of purchase. In the interest of product improvement, specifications, weights and dimensions are subject to change without notice. Up-to-date engineering data and more can be found at www.BaltimoreAircoil.com.

1. Coil Connections; 2. Make-up ND50; 3. Overflow ND50; 4. Water Out; 5. Water In; 6. Drain ND50; 7. ICE LOGIC®.

Model TSU

Water Pull Down Coil Op. Weight Sh. Weight Air Pump Volume Volume Volume (kg) (kg) (kW) (l) (l) (l)

R-717 Charge (kg)

Water Conn. In ND (mm)

Water Conn. Out ND (mm)

H (mm)

H1 mm

L (mm)

W (mm)

TSU-95C

9370

2550

0,75

6520

165

297

128

80+2x40

80

2160

2311

3073

1308

TSU-115C

10560

2780

0,75

7440

208

340

147

80+2x40

80

2160

2311

3683

1308

TSU-120C

10980

2860

0,75

7760

227

368

159

80+2x40

80

2160

2311

3073

1600

TSU-145C

13070

3270

0,75

9390

265

453

196

80+2x40

80

2160

2311

3683

1600

TSU-170C

15240

3860

0,75

11020

303

510

220

80+2x40

80

2160

2311

4293

1600

TSU-200C

17460

4225

1,1

12640

341

566

244

100+2x50

100

2160

2311

4877

1600

TSU-225C

19550

4635

1,1

14270

379

657

281

100+2x50

100

2160

2311

5486

1600

TSU-185C

16935

4045

1,1

12270

341

595

257

100+2x50

100

2160

2360

3073

2400

TSU-230C

20205

4635

1,1

14880

416

680

294

100+2x50

100

2160

2360

3683

2400

TSU-270C

23475

5180

1,1

17450

454

821

354

100+2x50

100

2160

2360

4293

2400

TSU-310C

26970

5950

1,5

20020

530

906

391

100+2x50

100

2160

2360

4877

2400

TSU-350C

30240

6495

1,5

22640

606

1020

440

150+2x80

150

2160

2360

5486

2400

TSU-290C

25105

5495

1,5

18700

492

878

379

150+2x80

150

2160

2360

3683

2982

TSU-340C

29145

6130

1,5

21960

606

1020

440

150+2x80

150

2160

2360

4293

2982

TSU-400C

33505

7085

1,5

25120

681

1161

501

150+2x80

150

2160

2360

4877

2982

TSU-450C

37545

7765

1,5

28470

757

1275

550

150+2x80

150

2160

2360

5486

2982

Baltimore Aircoil

TSU - F 21

TSU-480C - TSU-1050C & TSU-790D - TSU-1440D REMARK: Do not use for construction. Refer to factory certified dimensions & weights. This brochure includes data current at time of publication, which should be reconfirmed at the time of purchase. In the interest of product improvement, specifications, weights and dimensions are subject to change without notice. Up-to-date engineering data and more can be found at www.BaltimoreAircoil.com.

Water Sh. Weight Air Pump Volume (kg) (kW) (l)

Water Conn. Out ND (mm)

H (mm)

H1 L W (mm) (mm) (mm)

150+2x80

150

2160

2360

6096

2982

770

150+2x80

150

2160

2360

7290

2982

892

150+2x80

150

2160

2360

8509

2982

1002

200+2x80

200

2160

2360

9703

2982

2605

1125

200+2x80

200

2160

2360 10922 2982

1779

3115

1345

200+2x80

200

2160

2360 12725 2982

1510

2750

1187

200+2x80

200

2415

2757

7290

3582

1630

3115

1345

200+2x80

200

2415

2757

8509

3582

1780

3455

1492

200+2x80

200

2415

2757

9703

3582

1638

200+2x80

200

2415

2757 10922 3582

1869

200+2x80

200

2415

2757 12725 3582

Model TSU

Op. Weight (kg)

Pull Down Coil R-717 Water Conn. Volume Volume Charge In ND (l) (l) (kg) (mm)

TSU-480C

42180

8945

1,5

31610

833

TSU-590C

50260

10355

3,0

38000

1022

1784

TSU-700C

58450

11670

3,0

44670

1173

2067

TSU-800C

67195

13620

3,0

51140

1363

2322

TSU-910C

75365

14985

3,0

57610

1514

TSU-1050C

87805

17210

3,0

67300

TSU-790D

68450

13790

3,0

51860

TSU-940D

79380

15470

3,0

60570

TSU-1080D

91270

17920

3,0

69650

TSU-1220D

102970

19550

4,0

78360

1890

3795

TSU-1440D

118940

22090

4,0

91230

2230

4330

1529

660

... because temperature matters

Thermal Storage Products

1. Coil Connections; 2. Make-up ND50; 3. Overflow ND50; 4. Water Out; 5. Water In; 6. Drain ND50; 7. ICE LOGIC®.

TSU - F 22

TSC-95C - TSC-1050C & TSC-790D - TSC-1440D

TSU

REMARK: Do not use for construction. Refer to factory certified dimensions & weights. This brochure includes data current at time of publication, which should be reconfirmed at the time of purchase. In the interest of product improvement, specifications, weights and dimensions are subject to change without notice. Up-to-date engineering data and more can be found at www.BaltimoreAircoil.com.

Data Per Coil Model TSC

No° Coils

Sh. Weight (kg)

Coil Volume (l)

R-717 Charge (kg)

H (mm)

H1 (mm)

L (mm)

W (mm)

TSC-95C TSC-115C TSC-120C TSC-145C TSC-170C TSC-200C TSC-225C

1 1 1 1 1 1 1

1065 1205 1315 1500 1635 1950 2135

297 340 368 453 510 566 651

128 147 159 196 220 244 281

1912 1912 1912 1912 1912 1912 1912

2260 2260 2260 2260 2260 2260 2260

2654 3258 2654 3258 3861 4464 5070

1055 1055 1350 1350 1350 1350 1350

TSC-185C TSC-230C TSC-270C TSC-310C TSC-350C

2 2 2 2 2

1065 1205 1340 1590 1725

297 340 410 453 510

128 147 177 196 220

1912 1912 1912 1912 1912

2260 2260 2260 2260 2260

2654 3258 3861 4464 5070

1055 1055 1055 1055 1055

TSC-290C TSC-340C TSC-400C TSC-450C

2 2 2 2

1500 1635 1950 2135

453 510 566 651

196 220 244 281

1912 1912 1912 1912

2260 2260 2260 2260

3258 3861 4464 5070

1350 1350 1350 1350

TSC-480C TSC-590C TSC-700C TSC-800C TSC-910C TSC-1050C

4 4 4 4 4 6

1365 1545 1680 2000 2180 1680

380 462 519 574 660 520

164 199 224 248 285 225

1912 1912 1912 1912 1912 1912

2260 2260 2260 2260 2260 2260

2721 3327 3928 4534 5137 4030

1350 1350 1350 1350 1350 1350

TSU-790D TSU-940D TSU-1080D TSU-1220D TSU-1440D

4 4 4 4 4

2065 2315 2720 2950 3310

687 779 864 950 1084

297 336 373 410 468

2102 2102 2102 2102 2102

2448 2448 2448 2448 2448

3327 3931 4534 5140 6045

1645 1645 1645 1645 1645

General Notes 1. All dimensions are in mm. Weights are in kg. 2. Unit should be continuously supported on a flat levelsurface. 3. All connections are threaded

4. H1 = installed height. Coils are capped for shipping and storage. Add 75 mm for shipping height. 5. Refrigerant charge listed is operating charge for pump recirculated bottom feed. For other feed systems, consult your BAC Balticare Representative.

Baltimore Aircoil

TSU - F 23

Custom Coils for External Melt Application (TSU-C/D)

BAC can predict the temperatures required on an hour by hour basis for building ice on custom coils, over a variety of conditions and build times. Coils installed in Concrete Tank The physical space available, load profile, discharge temperatures, chiller capacity and operating sequences can be evaluated to find the design that best meets the application. The ICE CHILLER® Thermal Storage Coils are constructed of continuous 26,7 mm O.D. all prime surface serpentine steel tubing. The coils are assembled in a structural steel frame designed to support the weight of the coil stack with a full ice build for glycol (ammonia) application. After fabrication the coils are tested for leaks using 15 bar (31bar) air pressure under water, then hotdip galvanized for corrosion protection. The coils are configured to provide countercurrent glycol flow in adjacent circuits for maximum storage capacity. Individual coils can be factory-assembled into modules of two (2) coils for optimization of transport cost and reduction of site assembly time. Glycol manifolds are coated with zinc-rich, cold galvanizing finish at the factory. Necessary support steel and lifting lugs are provided on the modules to allow for lifting into and final positioning within the storage tank.

Modes of Operation The ICE CHILLER® Thermal Storage Unit operates in two main operating modes or cycles. A possible combination of these cycles of operation provides the flexibility to meet the daily HVAC or cooling requirements. Long periods of simultaneously circulating glycol or ammonia through the coil tubes and circulating water through the ICE CHILLER® should however be avoided to optimise system performance. Ice Build: In this operating cycle, ice is built by circulating ammonia or a 30% solution (by weight) of inhibited ethylene/propylene glycol through the coils contained in the ICE CHILLER® Thermal Storage Unit. The below table illustrates typical temperatures for 8, 10, 12 and 14 hour build cycles. At the start of the ice build cycle, the temperature will be higher while at the end of the ice build cycle, the temperatures will be lower.

... because temperature matters

Thermal Storage Products

BAC will manufacture custom ICE CHILLER® Thermal Storage Coils to meet project specific requirements. B.A.C. has done extensive research and testing on the build and melt characteristics of ice storage. This research and testing has resulted in selection capabilities unmatched by any other company in the industry.

TSU - F 24

Unit Capacity & Average Temperatures for Glycol Applications

TSU

Build Time (h) & Glycol Temperature (°C) Model TSU

Nominal Capacity (kWh)

Flow (l/s)

Δp In

Out

In

Out

In

Out

In

Out

TSU-95C

325

2,4

111,0

-8,8

-4,4

-6,9

-3,4

-5,8

-2,8

-5,0

-2,4

TSU-115C

404

2,4

130,3

-9,4

-3,8

-7,4

-2,9

-6,2

-2,4

-5,3

-2,1

TSU-120C

422

2,8

100,7

-9,0

-4,2

-7,1

-3,2

-5,9

-2,7

-5,1

-2,3

8h

10 h

12 h

14 h

TSU-145C

510

2,8

117,9

-9,5

-3,7

-7,5

-2,8

-6,3

-2,4

-5,4

-2,1

TSU-170C

597

2,8

134,4

-10,0

-3,2

-7,9

-2,4

-6,6

-2,1

-5,7

-1,8

TSU-200C

703

5,4

71,0

-8,7

-4,4

-6,9

-3,4

-5,8

-2,9

-4,9

-2,5

TSU-225C

791

5,4

78,6

-9,0

-4,2

-7,1

-3,2

-5,9

-2,7

-5,1

-2,3

TSU-185C

650

4,7

111,0

-8,8

-4,4

-6,9

-3,4

-5,8

-2,8

-5,0

-2,4

TSU-230C

808

4,7

130,3

-9,4

-3,8

-7,4

-2,9

-6,2

-2,4

-5,3

-2,1

TSU-270C

949

8,5

63,4

-8,4

-4,8

-9,6

-3,7

-5,6

-3,1

-4,8

-2,7

TSU-310C

1090

8,5

71,0

-8,7

-4,5

-6,8

-3,5

-5,7

-2,9

-4,9

-2,5

TSU-350C

1230

8,5

78,6

-8,9

-4,3

-7,1

-3,3

-5,9

-2,8

-5,1

-2,4

TSU-290C

1020

5,7

117,9

-9,5

-3,7

-7,5

-2,8

-6,3

-2,4

-5,4

-2,1

TSU-340C

1195

5,7

134,4

-10,0

-3,2

-7,9

-2,4

-6,6

-2,1

-5,7

-1,8

TSU-400C

1406

10,7

71,0

-8,7

-4,4

-6,9

-3,4

-5,8

-2,9

-4,9

-2,5

TSU-450C

1582

10,7

78,6

-9,0

-4,2

-7,1

-3,2

-5,9

-2,7

-5,1

-2,3

TSU-480C

1688

10,7

93,8

-9,2

-4,1

-7,2

-3,1

-6,1

-2,6

-5,2

-2,2

TSU-590C

2075

10,7

108,2

-9,7

-3,4

-7,7

-2,6

-6,4

-2,2

-5,6

-1,9

TSU-700C

2462

11,4

135,8

-10,1

-3,1

-8,0

-2,3

-6,7

-1,9

-5,8

-1,7

TSU-800C

2813

21,5

72,4

-8,7

-4,4

-6,9

-3,4

-5,8

-2,9

-4,9

-2,5

TSU-910C

3200

21,5

79,3

-9,0

-4,2

-7,1

-3,2

-5,9

-2,7

-5,1

-2,3

TSU-1050C

3692

17,0

137,3

-10,1

-3,1

-8,0

-2,4

-6,7

-2,0

-5,7

-1,7

TSU-790D

2776

27,4

73,1

-8,2

-5,0

-6,5

-3,8

-5,4

-3,2

-4,7

-2,8

TSU-940D

3303

27,4

82,7

-8,6

-4,6

-6,7

-3,6

-5,7

-3,0

-4,8

-2,6

TSU-1080D

3795

27,4

91,7

-8,8

-4,4

-7,0

-3,3

-5,8

-2,8

-5,0

-2,4

TSU-1220D

4287

27,4

100,7

-9,1

-4,1

-7,2

-3,1

-6,1

-2,6

-5,2

-2,3

TSU-1440D

5060

27,4

114,5

-9,6

-3,6

-7,6

-2,7

-6,3

-2,3

-5,4

-2,0

Unit Capacity for Ammonia Applications

Model TSU

Pump Recirculation Refrigerant Feed

Gravity Flooded Refrigerant Feed

Nominal Capacity kWh

Nominal Capacity kWh

Model TSU

Pump Recirculation Refrigerant Feed

Gravity Flooded Refrigerant Feed

Nominal Capacity kWh

Nominal Capacity kWh

TSU-95C

318

270

TSU-400C

1322

1164

TSU-115C

389

331

TSU-450C

1470

1322

TSU-120C

404

344

TSU-480C

1656

1417

TSU-145C

492

425

TSU-590C

2015

1737

TSU-170C

580

506

TSU-700C

2356

2018

TSU-200C

661

583

TSU-800C

2683

2366

TSU-225C

735

668

TSU-910C

2982

2680

Baltimore Aircoil

TSU - F 25

Unit Capacity for Ammonia Applications

Model TSU

Pump Recirculation Refrigerant Feed

Gravity Flooded Refrigerant Feed

Nominal Capacity kWh

Nominal Capacity kWh

636

545

TSU-185C

Model TSU

Pump Recirculation Refrigerant Feed

Gravity Flooded Refrigerant Feed

Nominal Capacity kWh

Nominal Capacity kWh

3576

3116

TSU-1050C

777

668

TSU-790D

2704

2281

910

798

TSU-940D

3170

2692

TSU-310C

1037

921

TSU-1080D

3615

3073

TSU-350C

1157

1041

TSU-1220D

4040

N.A.

TSU-1440D

4639

N.A.

TSU-290C

984

847

TSU-340C

1160

1009

Temperatures for Ammonia Applications Design Evaporator Temperature Pump Recirculation Refrigerant Feed °C

Design Evaporator Temperature Gravity Flooded Refrigerant Feed °C

Build Time

Build Time

Storage Factor

8h

10 h

12 h

14

Storage Factor

8h

10 h

12 h

14 h

1,00

-6,1

-4,9

-4,1

-3,6

1,00

-5,8

-4,8

-4,2

-3,7

1,05

-5,7

-4,6

-3,9

-3;4

1,05

-5,5

-4,6

-3,9

-3,5

1,10

-5,3

-4,3

-3,7

-3,2

1,10

-5,2

-4,3

-3,7

-3,3

1,15

-5,0

-4,1

-3,5

-3,0

1,15

-5,0

-4,1

-3,6

-3,2

1,20

-4,7

-3,9

-3,3

-2,8

1,20

-4,7

-3,9

-3,4

-3,0

1,25

-4,5

-3,7

-3,1

-2,7

1,25

-4,5

-3,8

-3,3

-2,9

1,30

-4,3

-3,5

-3,0

-2,6

1,30

-4,3

-3,6

-3,1

-2,8

Ice Melt: In this operation cycle the warm return water is cooled by direct contact between the water and the ice, melting ice stored in the modular ICE CHILLER® Thermal Storage Unit.

System Schematics The basic ice storage system includes an ICE CHILLER® Thermal Storage Unit, a refrigeration system and ice water pump as shown below. The ICE CHILLER® Unit consists of a multiple tube serpentine coil submerged in an insulated tank of water. Both the coil and tank are constructed from hot-dip galvanized steel for corrosion protection. When no cooling load exists, the refrigeration system operates to build ice on the outside surface of the coil. This refrigeration effect is provided by feeding refrigerant directly into the coil. To increase the heat transfer during the ice build cycle the water is agitated by air bubbles from a low pressure distribution system beneath the coil. When the ice has reached design thickness, BAC’s exclusive ICE-LOGIC Ice Thickness Controller sends a signal to turn off the refrigeration system. When chilled water is required for cooling, the chilled water pump is started, and the melt out cycle begins. Warm water returning from the load circulates through the ICE CHILLER® tank and is cooled by direct contact with the melting ice. During this cycle, the tank water is also agitated to enhance heat transfer and typically provides a constant supply water temperature of 1°C or less.

... because temperature matters

Thermal Storage Products

TSU-230C TSU-270C

TSU - F 26

For a closed chilled water loop see figure below. With this system, warm return water from the load is pumped through a heat exchanger and cooled by the ice water circuit from the ICE CHILLER® Unit.

TSU

For more detailed information on the design and operation of BAC ICE CHILLER® Thermal Storage Units, contact your local BAC Balticare Representative.

Basic Scheme – External Melt

Baltimore Aircoil

Scheme with Intermediate Heat Exchanger

TSU - F 27

Engineering Specifications TSU-C/D 1.0 ICE CHIILLER® Thermal Storage Unit 1.1 General: The ICE CHILLER® Thermal Storage Unit shall be Baltimore Aircoil Model TSU-______. Overall unit dimensions shall not exceed approximately _____ m by ____ m with an overall height not exceeding ____ m. The operating weight shall not exceed _______ kg

1.3 Experience: Manufacturers submitting bids for equipment in this specification shall have a standard production model of this unit, which has been manufactured and in use for 3 years. The manufacturer shall offer evidence that the equipment has been successfully operated on a minimum of 50 applications, which utilize the same refrigerant and meltout arrangement specified.

2.0 Construction Details 2.1 Tank: The tank shall be constructed of heavy gauge Z600 hotdip galvanized steel and reinforced with full-length structural angles underneath and on all four sides. All seams shall be welded to ensure watertight cnostruction. A zinc rich coating shall be applied to all exposed edges and welds. 2.2 Coil: The coil shall be constructed of prime surface serpentine steel circuits and shall be tested at 15 bar (31 bar for ammonia applications) air pressure under water. The coil shall be encased in a steel frame and the entire assembly hot-dip galvanised after fabrication. For use with Ammonia refrigerant, the coil shall be complete with purge connection for oil maintenance. 2.3 Insulation: Extruded polystyrene insulation shall be provided between the tank and the exterior panels. The insulation shall be 80 mm thick on the tank sides and ends, and 50 mm thick on the bottom and inside the covers.

2.4 Exterior Panels: Exterior panels sealed at all seams provide a complete vapour barrier and protect the insulation. They are furnished with B.A.C.’s exclusive BALTIBOND® Corrosion Protection System. 2.5 Covers: The ICE CHILLER® unit(s) shall be provided with sectional insulated steel covers provided with the BALTIBOND® Corrosion Protection System. 2.6 Ice Thickness Control: A sensing element shall be mounted on the coil to deactivate the refrigerant compressor at a full build of ice. 2.7 Air pump: Centrifugal regenerative blower for field mounting to supply low pressure air for agitation of the water. Pump is complete with a weather protected inlet air filter, and is suitable for outdoor applications. 2.8 Air Distributor: Low pressure air shall be distributed through multiple perforated PVC pipes.

... because temperature matters

Thermal Storage Products

1.2 Thermal Capacity: Each unit shall have a thermal storage capacity of _______ kWh operating with ___________refrigerant and

a build time of _______ hours at a _______ °C nominal evaporator temperature.

TSU - F 28

Engineering Considerations ICE CHILLER® Products

TSU

Installation ICE CHILLER® Thermal Storage Units must be installed on a continuous flat level surface. The pitch of the slab must not exceed 3 mm over a 3 metre span – See Figure: Unit Layout Guidelines. The units should be positioned so there is sufficient clearance between units and adjacent walls to allow easy access. When multiple units are installed, a minimum of 50 cm is recommended between units. When installed indoors, the access and slab requirements described above also apply. The units should be placed close to a floor drain in the event they need to be drained. The minimum height requirement above the tank for proper pipe installation is 1 metre. The below figure illustrates the recommended overhead clearance for ICE Unit Layout Guidelines CHILLER® Thermal Storage Units. BAC's ICE CHILLER® Thermal Storage Units are available unassembled when the units must be installed indoors and access is limited. Erection of unassembled units will require factory personnel to assist in the field assembly of this equipment. Contact the local BAC-Balticare Representative for additional details. For large applications, BAC will provide ICE CHILLER® Thermal Storage Coils for installation in field fabricated concrete tanks. This product offering demonstrates BAC's product design and flexibility. When coils are required, BAC's manufacturing capabilities allow coils to be manufactured in the size and configuration necessary to meet specific site and performance requirements. The concrete tank design is to be completed by a qualified structural engineer. The below figure illustrates the ICE CHILLER® Thermal Storage Coil layout guidelines. Buoyancy forces due to the density difference between ice and water require that hold–down angles be installed on top of the coils. This will prohibit the coils from floating in an overcharged condition. For large projects that require ICE CHILLER® Coils, contact the local BAC Balticare Representative for selection and dimensional information.

Recommended Overhead Clearance

Baltimore Aircoil

Coil Layout Guidelines

TSU - F 29

Unit Piping Piping to the ICE CHILLER® Thermal Storage Unit should follow established piping guidelines. The coil connections on the unit are galvanized steel and are grooved for mechanical coupling.

CAUTION: The system must include an expansion tank to accommodate changes in fluid volume. Adequately sized air vents must be installed at the high points in the piping loop to remove trapped air from the system. In cases where the piping to the storage tanks is at the highest elevation in the loop, purge valves must be installed in the piping on top of the units to remove excess air from the system.

Below figure illustrates reverse return piping for multiple units installed in parallel. The use of reverse return piping is recommended to ensure balanced flow to each unit. Shut off valves at each unit can be used instead of balancing valves. When large quantities of ICE CHILLER® Thermal Storage Units are installed, the system should be divided into groups of units. Then, balancing of each unit can be eliminated and a common balancing valve for each group of units installed. Shut off valves for isolating individual units should be installed but not used for balancing glycol flow to the unit.

Single Unit Valve Arrangement

Reverse Return Piping

Controls An inventory control that provides a 4 –20 mA signal is available. This control should be used for determining the amount of ice in inventory and to terminate the ice build cycle. Compolete operating control details are provided in the Operating and Maintenance Manual.

Glycol ICE CHILLER® Thermal Storage Units typically use a 25% (by weight) solution of industrially inhibited ethylene glycol for both corrosion protection and freeze protection. Industrial grade inhibited ethylene glycol is specifically designed to prevent corrosion in HVAC and heat transfer equipment. Inhibitors are used to prevent the ethylene glycol from becoming acidic and to protect the metal components in the thermal storage system. The system’s lowest operating temperature

... because temperature matters

Thermal Storage Products

For single tank applications, each pair of manifolded coil connections should include a shut off valve so the unit can be isolated from the system. Below figure illustrates the valve arrangement for a single unit. It is recommended that the piping include a bypass circuit to allow operation of the system without the ICE CHILLER® Thermal Storage Unit in the piping loop. This bypass can be incorporated into the piping design by installing a three-way/modulating valve. This valve can also be used to control the leaving glycol temperature from the thermal storage unit. Temperature and pressure taps should be installed to allow for easier flow balancing and system troubleshooting. A relief valve, set at a maximum of 10 bar, must be installed between the shut off valves and the coil connections to protect the coils from excessive pressures due to hydraulic expansion. The relief valve should be vented to a portion of the system, which can accommodate expansion.

TSU - F 30

should be 3°C to 4°C above the glycol freeze point. The freeze point for a system with 25% (by weight) ethylene glycol is -12°C. CAUTION: 1. Uninhibited ethylene glycol and automotive antifreeze solutions are NOT to be used on thermal storage applications.

2. Ethylene glycol solutions are NOT compatible with galvanised steel parts. Therefore glycol piping should only be galvanised at the outside.

TSU

Water Treatment In the near freezing temperatures of the ICE CHILLER® Thermal Storage Unit, scale and corrosion are naturally minimized. Therefore, water treatment for these two conditions may not be required or may require minimal attention unless the water is corrosive in nature. To control biological growth, a biocide may be needed to prevent the spread of iron bacteria or other organisms. For specific recommendations, consult a reputable local water treatment company and follow the guidelines below: Property of Water

Range

PH

7.0 to 9.0 (1)

Hardness as CaCO3

30 to 50 mg/l

Alkalinity as CaCO3

500 mg/l max.

Total Dissolved Solids

1000 mg/l max.

Chlorides

125 mg/l max. as Cl

Sulfates

125 mg/l max.

Conductivity

700 µS/cm at 0°C (2)

Notes: 1. A water pH of 8.3 or higher will require periodic passivation of the galvanised steel to prevent “white rust”, the accumulation of white, waxy, non-protective zinc corrosion products on galvanised steel surfaces.

2. Maximum conductivity of 700 µS/cm at 0°C is important for proper operation of the ICE LOGIC ice quantity controller.

If water treatment is implemented to the system, to assure full capacity of the ICE CHILLER® Thermal Storage Unit, the water treatment should not alter the freeze point of water.

Winterization Precautions must be taken to protect the unit and associated piping from freezing conditions. Heat tracing and insulation should be installed on all piping connected to the unit. The sight tube, operating controls and optional inventory sensor must be heat traced and insulated. It is not necessary to drain the unit during cold weather. Freezing of the water contained in the unit during the winter will not damage the coil or unit.

Pressure Drop The ICE CHILLER® Thermal Storage Unit is designed for low pressure drop. Pressure drops, for different flow rates and for alternative fluids, are available by contacting the local BAC Balticare Representative.

Warranties Please refer to the Limitation of Warranties applicable to and in effect at the time of the sale/ purchase of these products.

Baltimore Aircoil

TR - G 1

Content Connection Guide ...................................................................................... G2 Materials of Construction ......................................................................... G4 Selection Software ..................................................................................... G5 The Value of Standards ............................................................................. G6 Selection of Remote Sump Tank .............................................................. G7 Filtration Options .................................................................................... G13 Sound Reduction Options ....................................................................... G14 Fundamentals of Sound .......................................................................... G22 Motor Controls ........................................................................................ G47 Plume Abatement .................................................................................... G49 Formulas .................................................................................................. G51 Replacement Parts .................................................................................. G52 Application Guidelines ............................................................................ G53 Glossary .................................................................................................... G61

TR - G 2

Connection Guide Introduction A summary of connection types used by BAC follows. The specific connection type for a particular BAC model can be found on the unit print drawing or from your local BAC Balticare Representative.

Beveled for Welding (BFW) This connection type is a pipe stub with a “beveled” edge. The bevel allows for easier welding in the field and a full penetration weld. Weld materials fill the trimmed area between two beveled edges as shown here.

Grooved to suit a Mechanical Coupling This connection type is a pipe stub with a groove to accept a mechanical pipe coupler.

Stud Circle Flat Face Flange This connection type is a standard bolt and hole pattern at the point of connection to mate to a EN 1092 Flat Face Flange. When BAC provides this connection type to a hot water basin, mounting bolts are permanently fastened to the connection plate. All other components (piping, nuts, bolts, flatwashers, etc.) are provided by others unless otherwise specified.

Male Pipe Thread (MPT) This connection type is a threaded pipe stub connection designed to mate with a Female Pipe Thread (FPT) fitting.

Side Outlet Depressed Sump Box This option is offered to facilitate horizontal piping below the cold water basin of a unit, and is a compact alternative to using an elbow in the piping arrangement, saving installation time and cost.

Weld Details 1. Weld Material, 2. Beveled edge of field-installed piping, 3.Beveled Edge of BAC connection.

Grooved Connection 1. Grooved for mechanical coupling

Baltimore Aircoil

TR - G 3

Flat Face Flange pattern is shown on this cold water basin panel to suit a EN 1092 flange

Flat Fac Flange pattern with mounting bolts is shown on this hot water basin panel to suit a EN 1092 flange

MPT Connection

Side Outlet Depressed Sump Box

... because temperature matters

TR - G 4

Materials of Construction Introduction Operating environment, desired life expectancy, and budget all influence the materials of construction selected for an evaporative cooling unit. BAC products are available in a variety of materials and BAC designs focus on long life and easy maintenance. As a result, owners can maximize their operational goals. This section describes the materials of construction available for BAC products. To determine the best material options for your specific project, consult your local BAC Balticare Representative.

Galvanized Steel Z-600 hot-dip galvanized steel is the heaviest commercially available galvanized steel, universally recognized for its strength and corrosion resistance. To assure long-life, Z-600 hot-dip galvanized steel is used as the base material for all steel products and parts, and all exposed cut edges are protected with a zinc-rich coating after fabrication. With good maintenance and proper water treatment, Z-600 galvanized steel products will provide excellent service life under the operating conditions normally encountered in comfort cooling and industrial applications.

Baltibond® Corrosion Protection System The BALTIBOND® Corrosion Protection System is a unique system approach to evaporative cooling equipment protection. A special hybrid polymer, formulated for tenacious bonding, toughness, and impermeability to fluids, is applied by electrostatic spray to Z-600 hot dip galvanized steel surfaces. The polymer undergoes a heat-activated, thermosetting cure process, fuse-bonding it to the galvanized steel substrate. The BALTIBOND® Corrosion Protection System can extend the service life of equipment and alleviates concerns with white rust, virtually eliminating the need for periodic passivation of galvanized steel components.

Stainless Steel In certain critical applications the use of stainless steel is preferred. BAC offers stainless steel as an optional material on most of its product lines. Two types of stainless steel are available, AISI 304 (DIN Werkst. Nr. 1.4301) or AISI 316 (DIN Werkst. Nr. 1.4401 or 1.4404). Stainless steel AISI 316 is recommended for applications with chloride concentrations of more than 500 ppm in the circulating water.

Component Construction In addition to the various materials available for the structure of its units, BAC carefully selects the materials used for all components of its products. Additional materials such as corrosion resistant fiberglass reinforced polyester (FRP), polyvinyl chloride (PVC), aluminum and copper are used for components when necessary to provide the corrosion resistance required of a unit providing evaporative cooling service.

Which material option is right for my project? Included within the product section of each open cooling tower, closed circuit cooling tower and evaporative condenser in this catalog is a discussion on construction options. These sections define the availability of certain materials and combinations of materials for each product. Refer to these sections for specific product information. Your local BAC Balticare Sales Representative can guide you on the proper unit construction for your specific project.

Baltimore Aircoil

TR - G 5

Selection Software Easy-to-Use Selection Software BAC has developed comprehensive selection software, which simulates the performance of evaporative cooling equipment for a broad range of climatic and operating conditions. The programme provides all technical data relevant to the selected model(s).

Cooling Tower Selections The selection programme provides the ability to make selections for a wide range of operating conditions simultaneously for different cooling tower product lines and hence allows side by side comparisons of different unit configurations. Product selections often contain reserve capacity at the design conditions. Selections can be optimised by maximising flow rates, hot and cold water temperatures, wet bulb temperatures or approach.

Closed Circuit Cooling Tower Selections The closed circuit cooling tower selection programme provides equipment selections for applications utilizing water, aqueous ethylene glycol or aqueous propylene glycol as the process fluid.

Evaporative Condenser Selections The evaporative condenser selection program provides equipment selections for applications utilizing R-717 (ammonia), R-22, and R-134a.

Accessories The selection program evaluates the use of accessories that may impact capacity (i.e., low-sound fans, sound attenuation, etc.)

Alternative Fan Speed Standard selections at nominal fan speed utilise a standard kW fan motor to meet full load performance. Alternative selections based on reduced fan speed (and motor kW) are also available.

Performance Curves The selection program generates performance curves based on flow rates ranging from 80% to 120% of the design flow rate. Performance curves are a graphical representation of the leaving water temperature versus the entering wet-bulb temperature, and are typically evaluated at a number of ranges.

Sound Data The selection program provides sound ratings for standard selections at any distance for your reference. For extremely sound sensitive installations, sound ratings are also available for units with low sound fans and sound attenuation.

... because temperature matters

TR - G 6

The Value of Standards Introduction Baltimore Aircoil strongly believes in the value of standards and independent certification programmes. Through this philosophy customers can be assured of consistent level of performance and quality when using BAC products and services.

ISO9001:2000 This fundamental belief is demonstrated first and foremost by ISO 9001:2000 Certification of BAC’s design, engineering, and manufacturing of evaporative cooling products. Compliance with ISO 9001:2000 standards offers BAC customers better, more consistent quality, reliable performance, and confidence that the product can be delivered on time and per the specifications. Consistent quality also reduces the potential for installation and operational problems. Any problems reported from the field receive swift corrective and preventative actions to prevent reoccurrence. This level of performance is assured through frequent internal training and audits, backed by rigorous external audits by an independent, ISO-accredited Registrar. ISO 9001:2000 also requires demonstrating continuous improvement of products, processes, and systems over time, benefiting both BAC and its many customers.

European Directives and Standards The design of BAC products is influenced by European Directives and recognised standards. Examples include the following: European Machine Directive 98/37/EC European Pressure Equipment Directive PED 97/23/EC
ATEX Directive: 94/9/EC
Low voltage directive 73/23/EEC, 93/68/EC
Electromagnetic Compatibility: 89/336/EEC, 92/31/EEC, 93/68/EEC, 2004/10/EC
EN 13741 Thermal performance acceptance testing of mechanical draught series wet cooling towers. Besides supporting these directives and standards, BAC actively works with industry organisations, such as ASHRAE, ASME, CEN, ARI, CTI, EUROVENT –CECOMAF, and FM to improve their standards and technical documentation, or develop standards or guidelines where none currently exist. For instance, BAC supported the development of the “Recommended Code of Practice to keep your Cooling System efficient and safe”, and the brochure “Evaporative Cooling, how efficient heat transfer technology helps to protect the environment”, both published by EUROVENTCECOMAF. More recently BAC supported the development of the VDMA Einheitsblatt 24649 “Empfehlungen zum wirksamen und sicheren Betrieb einer Verdunstungskühlanlage”. BAC is an active member of numerous trade associations in the US and in Europe. BAC strongly encourages customers, suppliers, and competitors to join us developing and supporting recognised standards and certification programmes for the benefit of the industry and the society as a whole. BAC welcomes feedback on this subject, which can be send to [email protected].



Eurovent-Cecomaf Recommended Code of Practice

Baltimore Aircoil

Eurovent-Cecomaf Evaporative Cooling Brochure

TR - G 7

Selection of Remote Sump Tank For an Open Cooling Tower Remote sump tanks are used on evaporative cooling systems to provide a means of cold water basin freeze protection during cold weather operation. The remote sump tank is usually located in a heated, indoor space, and may preclude the need to winterize the evaporative cooling equipment. A remote sump tank must provide sufficient storage volume to accommodate all the water that will drain back to it during cooling system shutdown, including: The total volume of water contained within the cooling tower during operation (cooling tower volume). • The volume of water contained in all system piping located above the operating water level of the remote sump tank (system piping volume).
The volume of water contained within any heat exchanger, or other equipment located above the operating water level of the remote sump tank that will drain to the tank when the cooling system is shut down (system components volume). The maximum volume of water contained within the cooling tower is the volume of water to the overflow level. Besides the water in the cold water basin during operation, this volume will take into consideration water in the distribution system, water in suspension in the wet deck, plus an allowance for the external pulldown from piping and other equipment. This simplified method is a conservative approach as it will not consider any volume reductions based on flow rates. For specific information for your application, contact your local BAC Representative.


Safety Factor When designing a remote sump tank, make sure that your basin has a net available volume that is 5% greater than the total volume required. The net available volume is the volume between the operating level and the overflow level in the remote sump tank The minimum operating level must be maintained in the remote sump tank to prevent vortexing of air through the tank's suction connection.

Example A VTL-059-H will be installed on a cooling tower/heat exchanger system that will utilize a remote sump tank. The tower side volume contained in the heat exchanger is 95 liters The system has been designed with 10 meter of DN 100 pipe that will be above the operating level of the remote sump tank. What is the correct remote sump tank volume? Solution: From Table 4, the cold water basin volume at overflow for the VTL-059-H is 555 liters. From Table 6, the DN 100 pipe will contain 8,2 liters of water per linear meter pipe. The total volume contained in the DN 100 pipe is 82 liters. The tower side volume of the heat exchanger is 95 liters. The total volume required is: Cooling Tower Volume at Overflow (555 liters) + System Piping Volume (82 liters) + System Components Volume (95 liters) = Total Volume 732 liters 732 liters x 1.05 (safety factor) = 770 liters required. From the above calculation the minimum volume of the remote sump tank must be 770 liters.

... because temperature matters

TR - G 8

Table 1 : Series 3000 - D S3000-D Cold Water Basin Volumes Model No.

at Operating Level (l)

at Overflow Level (l)

S3 D240L - S3 D299 L

1597

3626

S3 D333L - S3 D379 L

1597

3857

S3 D455L - S3 D527 L

2036

4879

S3 D412L - S3 D436 L

2036

4614

S3 D552L - S3 D672 L

3285

6764

S3 D728L - S3 D828 L

3285

8312

S3 D872L - S3 D970 L

3285

9330

S3 D1056L - S3 D985 L

3285

10121

S3 D473L - S3 D501 L

2710

5863

S3 D583L - S3 D725 L

4201

8282

S3 D1132L - S3 D1301 L

4201

12154

Table 2 : TXV TXV Cold Water Basin Volumes Model No.

at Operating Level (l)

at Overflow Level (l)

TXV 109 - TXV 154

508

2659

TXV 177 - TXV 193

679

3565

TXV 292 - TXV 237

720

4103

TXV 354 - TXV 500

1090

6213

TXV 310 - TXV 425

820

5341

Table 3 : FXT FXT Cold Water Basin Volumes Model No.

at Operating Level (l)

at Overflow Level (l)

FXT 27 - FXT 32

106

428

FXT 43 - FXT 51

155

553

FXT 60 - FXT 68

208

746

FXT 74 - FXT 88

310

1033

FXT 97 – FXT 133

477

1590

FXT 160 – FXT 173

636

2112

FXT 211 – FXT 250

636

2521

FXT 194 – FXT 266

954

3180

FXT 320 – FXT 346

1272

4224

FXT 422 – FXT 500

1272

5042

Baltimore Aircoil

TR - G 9

Table 4 : VTL VTL Cold Water Basin Volumes Model No.

at Operating Level (l)

at Overflow Level (l)

VTL 039 – VTL 079

290

555

VTL 076 – VTL 095

435

815

VTL 086 – VTL 137

580

1090

VTL 139 – VTL 215

875

1655

VTL 225

1170

2175

VTL 227

875

1655

VTL 238 – VTL 272

1170

2175

Table 5 : VXT VXT Cold Water Basin Volumes Model No. VXT

at Operating Level (l)

at Overflow Level (l)

VXT 10 – VXT 25

45

100

VXT 30 – VXT 55

100

210

VXT 65 – VXT 85

150

325

VXT 95 – VXT 135

205

435

VXT 150 – VXT 185

275

580

VXT N215 – VXT N265

850

1850

VXT N310 – VXT N395

1220

2810

VXT 315 – VXT 400

1400

2300

VXT N430 – VXT N535

1630

3765

VXT 470 – VXT 600

2125

3490

VXT 630 – VXT 800

2850

4680

VXT 870 – VXT 1200

4300

7060

Table 6 : Pipe Capacities Nominal Pipe Size

Inside Diameter

Volume per linear meter

Inches

mm

mm Based on Schedule 40 pipe

Liters

3 4 6

80 100 150

77,9 102,3 154,1

4,8 8,2 18,7

8 10 12

200 250 300

202,7 254,5 303,3

32,3 50,9 72,3

14 16 18

350 400 450

333,5 381,1 428,8

87,4 114,1 144,4

20 24

500 600

478,0 574,9

179,5 259,6

... because temperature matters

TR - G 10

For a Closed Circuit Cooling Tower or Evaporative Condenser Note: This section provides instruction in the selection of a remote sump tank for a closed circuit cooling tower or evaporative condenser only. Remote sump tanks are used on evaporative cooling systems to provide a means of cold water basin freeze protection during cold weather operation. When the recirculating pump of a closed circuit cooling tower or evaporative condenser is not operating, all of the recirculating water drains by gravity to the remote sump. The remote sump tank is usually located in a heated, indoor space, and may preclude the need to winterize the cold water basin. The remote sump must be sized to accommodate the suction head for the pump plus a surge volume to hold all the water that will drain back to the tank when the pump is shut down. This surge volume (also called drain down volume) includes water in the evaporative cooling equipment and water held in the piping between the unit and the remote sump. The volume of water in the evaporative equipment includes the water in suspension (water within the spray distribution system and falling through the heat transfer section) and water in the cold water basin during normal operation. Tables 1 through 4 provide the volume of water in suspension plus the water in the cold water basin, labeled as "basin volume at overflow level." Table 4 can be used to calculate the volume of water in the piping between the unit and the remote sump (includes riser and drain piping) for applications where piping is Schedule 40. To select a remote sump tank for a particular application, determine the total volume (spray water volume plus piping volume) and select a remote sump tank with a net available volume that is 5% greater than required. HFL hybrid closed circuit cooling towers do not require remote sumps. Due to their small water volume and the unique sump/ plenum design, they can switch from wet to dry operation and vice versa without the need to drain the sump. Electrical sump heaters will protect the sump from freezing at ambient temperatures as low as -25°C, even when the fan(s) is (are) in operation.

Application Notes The standard close-coupled centrifugal pump normally furnished with BAC units is designed and selected specifically for the pump head and flow rate required when the pump is mounted on the unit. This pump cannot be used for remote sump applications and is therefore omitted. The following factors should be considered when selecting remote pumps: Total static head from the remote sump tank operating level to the inlet of the evaporative equipment. Pipe and valve friction losses.
For all Closed Circuit Cooling Towers and all Evaporative Condensers, 14 kPa water pressure is required at the inlet of the water distribution system.
Required spray flow rate as shown in Tables 1 through 4. A valve should always be installed in the pump discharge line so that the water flow can be adjusted to the proper flow rate and pressure. Inlet water pressure should be measured with a pressure gauge installed in the water supply riser near the equipment inlet. The valve should be adjusted to permit the specified inlet pressure, which results in the design water flow rate.



Accurate inlet water pressure and flow rate are important for proper evaporative equipment operation. Higher pressure (in excess of 70 kPa) can cause leaks in the spray distribution system. Lower pressure or low flow may cause improper wetting of the coils, which will negatively affect thermal performance, promote scaling, and may also cause excessive drift. On remote sump applications, the standard float valve(s) and strainer(s) are omitted from the cold water basin and a properly sized outlet connection is added. The remote sump outlet connection is located on the bottom of most units. On smaller Series VL and VX units, the connection is located on the end or back side of the unit. To clarify the location of the remote sump outlet connection, refer to the appropriate unit print, available from your local BAC Balticare Representative or at www.BaltimoreAircoil.com. Another effect of using a remote sump is that the operating weight of the evaporative unit is reduced (design changes, the omission of the integral spray pump, and/or changes in cold water basin volume can contribute to this deduct).

Example An FXV-422 will be installed on a system that will also utilize a remote sump tank. The system has been designed with 12 meter of DN 150 mm pipe that will be above the operating level of the remote sump tank. What is the correct volume of the remote sump?

Baltimore Aircoil

TR - G 11 Solution: From Table 1, the spray water volume for an FXV-422 is 997 liters. From Table 4, the DN 150 mm pipe will contain 18,7 l/s of water per linear meter. The total volume contained in the DN 150 mm pipe is 12 meter x 18,7 liter/meter = 225 liters. The total volume required is: Spray Water Volume (997 liters) + System Piping Volume (225 liters) = Total Volume 1222 liters 1222 liters x 1,05 (safety factor) : 1283 liters required. From the above calculation the minimum volume of the remote sump tank must be 1283 liters.

Table 1 : FXV - CXV - HXI CXV – FXV – HXI Cold Water Basin Volumes Model No. CXV

Model No. FXV

Model No. HXI

at Operating Level (l)

CXV 74 - 93

FXV 42x

HXI 42x

556

997

12

150

CXV 117 - 147

FXV 43x

HXI 43x

847

1519

18

150

CXV 153 - 193

FXV (Q)44x

HXI 44x

1137

2041

24

200

CXV 207 - 296

FXV (Q)54x

HXI (Q)54x

685

2217

45

200

CXV 338 - 435

FXV (Q)56x

HXI (Q)56x

1036

3350

54

200

CXV 283 - 327

FXV 64x

HXI (Q)64x

785

2852

45

200

CXV 416 - 481

FXV (Q)66x

HXI (Q)66x

1187

4311

54

200

at Overflow Level Spray Water Flow (l) (l/s)

Outlet Size (3)

CXV D645 - D792

FXV D288

3207

5308

108,5

300

CXV D791 - D944

FXV D364

4259

6587

108,5

300

Spray Water Flow (l/s)

Outlet Size (3)

2,2

65

Table 2 : VXI - VXC VXI - VXC Cold Water Basin Volumes Model No. VXI

Model No. VXC

at Operating Level (l)

at Overflow Level

VXI 9-x

VXC 14 - 28

45

100

VXI 18-x

VXC 36 - 65

100

210

4,7

80

VXI 27-x

VXC 72 - 97

150

325

7,1

100

VXI 36-x

VXC 110 - 135

205

435

9,5

100

VXI 50-x

VXC 150 - 205

275

580

13,9

150

(l)

VXI 70-x

VXC 221 - 265

850

1850

19,2

150

-

VXC 357 - 454

1400

2300

30,8

200

VXI 180-x

VXC 562 - 680

2125

3490

46,7

250

-

VXC 714 - 908

2125

3490

61,6

250

VXI 360-x

VXC 1124 - 1360

4300

6420

93,4

300

VXI 95-x

VXC S288 - S350

805

1850

25,2

150

VXI 145-x

VXC S403 - S504

1220

2810

38,5

200

VXI 190-x

VXC S576 - S700

1820

3730

50,4

250

VXI 290-x

VXC S806 - S1010

2470

5690

77

300

VXI 144-x

VXC 495 - 516

1795

3410

39,1

200

VXI 215-x

VXC 715 - 804

2725

5175

56,8

250

VXI 288-x

VXC 990 - 1032

3655

6935

78,2

250

VXI 430-x

VXC 1430 - 1608

5515

10475

113,6

300

... because temperature matters

TR - G 12

Table 3 : VFL - VCL VFL - VCL Cold Water Basin Volumes Model No. VFL

Model No. VCL

at Operating Level (l)

at Overflow Level

VFL 24X

VCL 042-079

290

VFL 36X

VCL 084-133

VFL 48X

VCL 131-159

Spray Flow (l/s)

Outlet Size (3)

555

5,9

100

435

815

9,0

100

580

1090

12,1

150

(l)

VFL 72X

VCL 167-258

875

1655

17,9

150

VFL 96X

VCL 239-321

1170

2175

24,2

200

Table 4 : Pipe Capacities Nominal Pipe Size

Inside Diameter

Volume per linear meter

Inches

mm

mm Based on Schedule 40 pipe

Liters

3 4 6

80 100 150

77,9 102,3 154,1

4,8 8,2 18,7

8 10 12

200 250 300

202,7 254,5 303,3

32,3 50,9 72,3

14 16 18

350 400 450

333,5 381,1 428,8

87,4 114,1 144,4

20 24

500 600

478,0 574,9

179,5 259,6

Notes: 1. The overflow level is the spray water volume and based on the maximum operating water level in the cold water basin with no net drop leg included in the piping system below the unit outlet.

3. Drain connection size is for remote sump applications only. For location of drain connection, please refer to unit certified print or contact your local BAC Balticare representative.

2. All remote sump unit volumes are based on bottom outlets sized as noted, except those models with an asterisk, which are based on an end outlet sized as noted.

Baltimore Aircoil

TR - G 13

Filtration Options Separators Features











Available in flow rates from 2,5 to 76 l/sec. Automatic purge complete with electrically actuated industrial grade ball valve and adjustable purge timer. Close coupled, end suction centrifugal pump & TEFC motor. Cast iron pre-strainer with removable SST basket. Control Panel - IP65 fibreglass enclosure with motor start/ stop, circuit breakers, door disconnect switch, 3-position pump motor switch, adjustable 24 hours purge timer. Skid - fusion bonded polyester coated carbon steel. Polyester powder coated carbon steel interconnecting piping, includes flow controller and isolation ball valves. Options: package recovery system.

Application BAC's package separators are designed specifically to remove dirt, sand, silt, precipitates, and suspended solids from process fluids. The solids in suspension are separated using the centrifugal forces and moved in an accumulation chamber. The clean fluid is returned to the process. The system utilises an automatic purge to drain the separated solids. The separator will remove unwanted contaminates resulting in increased system efficiency and decreased operating costs. In conjunction with evaporative cooling equipment it is recommended to provide this equipment with a sump sweeper piping system.

Media Filters Designed for high pressure open applications - 700 kPa.

Features













Available in flow rates ranging from 1 to 12 l/sec. Positive filtration down to 10 micron (5 micron optional). Fusion bonded epoxy lined /polyester coated carbon steel vessel rated at 700 kPa (optional higher pressure ratings and ASME code stamp available). Industrial grade brass 3-way valves and polyester powder coated carbon steel face piping. Closed coupled, end suction centrifugal pump and TEFC motor with cast iron pre-strainer and SST basket. Skid - fusion bonded polyester coated carbon steel. Automatic control cabinet – IP 65 fibreglass enclosure including door disconnects switch, circuit/breaker protection, electric actuator, step-down transformer, 3position pump motor switch, pressure differential switch, adjustable solid state timer and 24 hours backwash clock. Source water back wash.

Application BAC's filtration systems are designed specifically to handle a wide variety of industrial water filtration applications. The permanent media filters use a silica sand media that easily backwashes for cleaning. The filter provides an excellent method for removing dirt, precipitates and suspended solids. In conjunction with evaporative cooling equipment it is recommended to provide this equipment with a sump sweeper piping system.

Service Technical field service representatives are available to provide guidance for application, installation and repair.

... because temperature matters

TR - G 14

Sound Reduction Options VX Sound Attenuation Sound Efficient and Flexible VX design Sound is an important consideration in the selection and application of evaporative cooling equipment. Depending on actual site conditions acceptable sound levels can differ greatly. The inherently quiet VX-line design and extensive range of VX sound attenuation options provide economic solutions for a wide variety of acoustical requirements. Arrangement

Day

Night

Typical Noise Criteria and NC Range

Standard VX unit

Base

- 8 dB (A)

Light industrial & commercial areas. NC-45 to NC-55

VX unit + XA

- 9 dB (A)

- 17 dB (A)

Business premises, laboratories occupied work areas . NC-40 to NC-45

VX unit + XB

- 17 dB (A)

- 25 dB (A)

Large offices, retail shops needing acceptable listening conditions. NC-35 to NC-40

VX unit + XC

- 21 dB (A)

- 29 dB (A)

Rural or residential environment. NC-30 to NC-35

Sound reductions shown are expressed as sound pressure data at 15 m from the air intake. Daytime : full fan speed. Night-time : derated to half speed.

Indoor Applications Directional free field sound data or overall sound power levels are not normally the best way to describe the acoustical behaviour of VX evaporative cooling equipment when installed indoors. In these cases Partial Sound Power levels are the best method to define the sound emission. Partial Sound Power levels represent the sound energy radiated from the sound source over a single directional flat surface (air intake and discharge). Partial Sound Power data for VX models are the result of extensive sound testing using the parallelepiped test methodology and describe the sound radiation for indoor environments.

Sound Testing VX VX Sound Attenuation Alternatives

Baltimore Aircoil

TR - G 15

1. XA Attenuator

2. XB Attenuator

3. XC Attenuator

Discharge attenuator with vertical baffles

Discharge attenuator with vertical baffles

Double discharge attenuator with vertical baffles.

Intake attenuator with angled baffles

Intake attenuator with additional baffles and not angled

Double intake attenuator with baffles not angled

Approximate distance between baffles is 300 mm Approximate distance between baffles is 120 mm Approximate distance between baffles is 120 mm

Scope of Supply









Intake attenuator with access plenum and access door at both unit ends. Discharge attenuator with access plenum and access door at the back of the unit. Acoustical baffles at both intake and discharge with flex tissue protection and encased in a galvanized steel frame with the Baltibond® Corrosion Protection System. Acoustical material that is resistant to water, biological and chemical attack. Acoustically insulated solid bottom panels mounted under the full length of the unit. Lubrication lines extended to the air intake side of the attenuator to facilitate lubrication of the fan shaft bearings. Internal fan screens at the air intake side of the unit to guard the fan and drive system. All steel parts are Z600 galvanized steel with BALTIPLUS Protection.

VX Sound Attenuation Options




All VX sound attenuator options can be supplied with BALTIBOND® Corrosion Protection System. The sound attenuators can be fitted with mesh screens at the intake and/or discharge. Optional perforated steel sheet is available for additional baffle protection.

VX Standard acoustical baffle

VL Sound Attenuation Combination of Low Heigth with Low Sound The Low Profile Series VL provides optimal solutions for sound sensitive installations requiring low equipment height. Different sound attenuation packages are available to meet specific sound and lay-out requirements. For Horizontal Air Intake, BAC offers two Sound Attenuation alternatives:

HS-Type

HD-Type with Double Intake Attenuator

... because temperature matters

TR - G 16 Vertical Air Intake Configurations In certain lay-out situations it may be desirable to install Low Profile Series VL products with VS vertical air intake and discharge sound attenuation. Such situations are usually limited to indoor installations where the equipment cannot be located at the perimeter of the building. VS attenuators incorporate the installation of discharge deflectors which guide the discharge air stream away from the air intake. Recycling of discharge air under all weather and wind conditions cannot however entirely be avoided, in particular for larger multi cell installations.

VS-Type

Sound Reductions Arrangement

Day

Night

Typical Noise Criteria & NC Range

Standard VL unit

Base

- 8 dB (A)

Acceptable working conditions in light industrial & commercial areas. NC-45 to NC-55

VL units + HS or VS

- 17 dB (A)

- 25 dB (A)

Large offices, retail shops needing acceptable listening conditions. NC-35 to NC-40

VL unit + HD

- 21 dB (A)

- 29 dB (A)

Good listening conditions, residential environment. NC-30 to NC-35

Sound reductions shown are expressed as sound pressure data at 15m from air intake. Daytime: full fan speed. Nighttime: derated to half fan speed

Indoor Applications Due to its low height, VL evaporative cooling equipment is the preferred choice for indoor applications. In such cases the sound emission and evaluation procedure is significantly different to open installations with free field sound radiation. For indoor applications Partial Sound Power levels are the best method to describe the sound emission. Partial Sound Power levels represent the sound energy radiated by the sound source over a single directional flat surface (air intake/ air discharge). All sound attenuators for Low Profile Series VL products can be applied for indoor use. Partial Sound Power data for VL models are the result of extensive sound testing using the parallelepiped methodology and describe the sound radiation in indoor environments.

Baltimore Aircoil

Sound Testing VL

TR - G 17 Easy Maintenance With evaporative cooling equipment ease of maintenance is linked to ease of access. All VL sound attenuators have been designed to provide spacious access to the interior areas and components of the unit requiring maintenance.

1. Discharge attenuator access door : The access door in the discharge attenuator provides easy access to the spray system and discharge attenuation baffles. 2. Pan access door : Circular door for access to the float ball adjustment and strainer 3. Intake attenuator access doors : Large twin access doors are located at both sides at the air intake attenuator. When removed, access is available to the fan motor and fan drive as well as the spray water pump.

Scope of Standard Supply








Intake attenuator with access plenum and large size access doors on both sides of the unit. Discharge attenuator with access plenum and access door. Bottom panel with drain (under fan section). Acoustical baffles with flex tissue protection and encased in a galvanized steel frame with BALTIBOND® Corrosion Protection System. Acoustical material that is resistant to water, biological and chemical attack. Lubrication lines extended to the air intake side of the attenuator to facilitate lubrication of the fan shaft bearings. All steel parts are Z600 galvanized steel with BALTIPLUS Protection.

... because temperature matters

TR - G 18 Available Options





All VL sound attenuator options can be supplied with the BALTIBOND® Corrosion Protection System. Relocation of the spray pump to the pipe connection end of the unit is available for easy access to the spray pump. The sound attenuators can be fitted with mesh screens at the intake and/or discharge. Optional perforated steel sheet is available for additional baffle protection.

Relocation of spray pump on VL unit

Axial Fan Sound Reduction Options Quiet Energy Efficient Solutions Inherently quiet axial fan products are BAC's Series 3000D cooling towers, FXV-D and CXV-D coil products, as well as the Series 1500 product lines. The induced draught crossflow and combined flow configuration of these product lines have a number of distinct advantages in terms of energy efficiency and sound radiation.





The waterborne noise is minimised by the gravity water distribution and crossflow fill arrangement, which leads the water down into the cold water basin without the typical splash noise of counterflow arrangements. This eliminates the need for installing expensive water silencers in the pan section of the equipment. The mechanical drive arrangement is inside the cooling tower casing.

Series 3000-D, FXV-D, CXV-D product lines

Series 1500 product lines

Standard Low Noise Fans All SERIES 3000-D Cooling Towers, FXV-D and CXV-D coil products as well as Series 1500 and HXI/HXC hybrid products are fitted with highly efficient low noise fans as standard. These fans have a special blade cord width and trailing edge arrangement. Due to their low tip speed extra low sound emissions are achieved.

Standard Low Noise Fan on S3000-D, FXV-D and CXV-D

Baltimore Aircoil

TR - G 19 Optional "Whisper Quiet" fans For extremely sound sensitive applications "Whisper Quiet" fans can be used in lieu of the standard Low Noise fans.

Series 3000-D cooling towers, FXV-D and CXV-D coil products : The "Whisper Quiet" fan option on Series 3000D, FXV-D and CXV-D coil products consists of a multi-blade aerofoil fan design with an exceptionally wide cord resulting in optimum high solidity for whisper quiet operation.

Specially shaped aerofoil blade design

Allowing individual adjustment or removal at standstill

Series 1500 product lines : On the Series 1500 product lines the "Whisper Quiet" fan option consists of a hub of one piece steel block with specially designed aluminium hinged blades and allowing individual adjustment or removal at standstill. The high solidity specially shaped blades with unique end caps result in whisper quiet operation.

Unique end cap design for further sound reduction

Allowing individual adjustment or removal at standstil.

... because temperature matters

TR - G 20 Induced Draft Attenuator Package To optionally match the most stringent acoustical requirements, the Induced Draft Attenuation Package is available for Series 3000D cooling towers, FXV-D and CXV-D coil products and Series 1500 products. The package consists of an acoustical enclosure of the fan discharge cowl and intake attenuation on each air inlet side. Intake attenuators have unique circular acoustical baffles in a staggered arrangement. Intake and discharge attenuators are always fitted together to obtain optimal acoustical performance. The attenuator package is available for standard low noise fans and on specific models fitted with the optional whisper quiet fans.

1. Discharge attenuator encloses fan section; 2. Intake Sound Attenuator (at each air inlet side)

Axial Fan Efficiency for Low Noise Applications Typical sound emission reductions achieved by BAC's axial fan product lines (Series 3000-D cooling towers, FXV-D & CXV-D coil products and Series 1500 product lines) are shown in the table below. Arrangement

Day

Night

Application

Standard Low Noise Fans

Base

- 8 dB(A)

Urban & light industrial

Standard Low Noise Fans with Sound Attenuation

- 5 dB(A)

- 13 dB(A)

Suburban & laboratories

"Whisper Quiet" Fans

- 12 dB(A)

- 18 dB(A)

Residential & commercial

"Whisper Quiet" Fans with Sound Attenuation*

- 15 dB(A)

- 20 dB(A)

Domestic & rural

* Available only for certain models.

Scope of Supply









Standard products have low noise axial fans comprising cast iron hub and multiple aluminium fan blades with adjustable pitch. Fan blades have a special blade cord width and trailing edge arrangement to optimise airflow and minimise noise. Optional "Whisper Quiet" fans on Series 3000D, FXV-D and CXV-D models are constructed of fibreglass reinforced plastic blades of specially shaped aerofoil design. The blades are fixed on a steel, plastic coated, fan hub by aluminium blade supports and fastened through U-bolts for simple field assembly. Optional "Whisper Quiet" fans on Series 1500 (TXV, FXV, CXV) products consist of one piece steel block hub and specially shaped aluminium hinged blades allowing simple field assembly and unique end caps. Factory assembled acoustical discharge enclosure (shipped loose for installation on site) is constructed of Z600 heavy-gauge hot-dip galvanised steel protected with the Baltiplus Corrosion Protection (exterior painting)

Baltimore Aircoil

TR - G 21


Factory assembled and installed intake attenuator comprising of a Z600 heavy gauge hot-dip galvanised steel protected with the Baltiplus Corrosion Protection (exterior painting). Circular acoustical baffles designed to minimise air pressure drop with acoustical materials resistant to water, biological and chemical attack.

Options




Air discharge screens fitted on the discharge attenuator. Air intake screens fitted on the intake attenuators. Sound attenuation with the Baltibond® Corrosion Protection System: All galvanised steel parts, baffles, are protected with the Baltibond® Corrosion Protection System.

Research and Development Thermal and acoustical properties are partners in the performance of evaporative cooling equipment and hence must be established and evaluated together. The thermal performance of BAC equipment is verified at the BAC Research and Development Centre, the most advanced in the industry. Large environmental test chambers and refrigeration systems are able to simulate a wide range of climate and system test conditions on full size equipment. Sound tests are conducted for equipment, with and without sound attenuation, at various directions, distances and fan speeds. At BAC thermal and sound test programmes go hand in hand, providing reliable data for a wide range of environmental and operating conditions.

Acoustical test

Thermal rating test BAC's Sound Data Sheets For product type units, BAC provides sound pressure data per octave band and sound power data for all four sides and the top of the unit. For indoor applications BAC provides partial sound data at both air inlet and discharge. For more information on acoustics please refer to the chapter "Fundamentals of Sound".

... because temperature matters

TR - G 22

Fundamentals of Sound Introduction Sound is an important consideration in the selection of mechanical equipment. The purpose of this article is to present a procedure for evaluating the sound levels created by evaporative cooling equipment to determine if these levels will be acceptable to the neighbors* who live or work near the installation. In addition, sound levels must comply with local code requirements. While most often these levels are found to be acceptable, certain situations may call for sound levels lower than those produced by the equipment. It is then the task of the manufacturer, engineer, and owner to determine the best way to decrease the sound levels for the particular installation. This article presents a means for assessing the impact of the evaporative cooling equipment’s sound on a neighbor and possible means to reduce that impact should it be a potential problem. The procedure consists of three steps, followed by a fourth step if necessary: 1. Establish the noise criterion for the equipment: i.e., determine the sound levels that will be considered acceptable by the neighbors who will be exposed to them. Also consult local codes for appropriate sound levels. For a general idea of how sound levels produced by a cooling tower compare to sound from other common sound sources, see the graph below.

2. Estimate the sound levels that will be produced by the equipment, taking into account the effects of equipment geometry, the installation, and the distance from the equipment to the neighbor.* 3. Compare the noise criterion with the expected sound levels to determine if the sound levels from the equipment will be acceptable. 4. In the event that the equipment sound levels are excessive for the particular site conditions, a method should be determined to modify the neighbor’s perception of the sound. There are three ways to change the effects that any undesirable sound has on the receiver of that sound: - Modify the source of the sound - Control the path of the sound - Adjust the receiver’s expectation or satisfaction, keeping in mind that sound can be very subjective and is highly dependent on perception Note: *In this article, the term “neighbour” is used to denote the person or group of persons to be protected against excessive sound levels created by the evaporative cooling equipment. It is intended that this include not only the occupants of other buildings, but also the occupants of the building served by the equipment.

Some ways that sound from BAC equipment can be adjusted for a more favorable impact on the receiver include:

Baltimore Aircoil

TR - G 23

Modify equipment location or position If possible, simply do not run the equipment at the critical time (at night for residential areas and during the day for office parks)
Install a second motor, two-speed motor, or VFD so that the unit can run at lower speeds when the full capacity is not required
Use a low sound fan
Oversize the equipment and run the fan at lower speed and power level
Construct sound barriers (sound walls, etc.) or use existing barriers (trees, other buildings, etc.) when planning the location of the equipment
Install sound attenuation (available on the air intake and air discharge of the equipment) The article also includes several appendices to lend assistance in understanding and performing some aspects of a sound analysis. Contact your local BAC Representative with questions on sound analysis or sound issues specific to your installation.



Terminology and Units of Measurement The following terms and units of measure are used in this article, in accordance with accepted U.S. Standards: Decibel (dB) – the unit of measurement used in sound control (dimensionless, used to express logarithmically the ratio of a sound level to a reference level). dB(A) – the A-weighted sound pressure level. Evaporative cooling equipment – used in this article to represent all BAC product lines in the sound analysis (includes open cooling towers, closed circuit cooling towers, and evaporative condensers). Frequency – the number of repetitions per unit time (the unit for frequency is the Hertz (1 cycle/s)). Hertz – abbreviated Hz, is the unit of frequency, defined as “cycles per second.” Noise – unwanted sound. Noise Criteria – the maximum allowable sound pressure level(s) (Lp) at a specific location. Criteria may be expressed as a single overall value or in individual octave bands. The NC values and curves are further explained throughout this article. Octave Band – a range of sound frequencies with an upper limit twice its lower limit. The bands are identified by their center frequencies (“identifying frequencies”), which is the square root of the product of the upper and lower cutoff frequencies of a pass band. These center frequencies and band widths are shown on page J23. In some sound data tables, these eight octave bands are also called by their “Band Numbers;” hence, the Band Numbers are also listed as such in this article, in addition to the BAC Sound Rating Program and BAC Selection Software. Sound – the sensation of hearing; rapid, small fluctuations to which our ears are more or less sensitive; small perturbation of the ambient state of a medium (ambient air in most cases) that propagate at a speed characteristic of the medium. Sound Pressure Level (Lp) in dB – a ratio of a sound pressure to a reference pressure and is defined as: Lp = 20LogP/0.002(dB), reference 0.0002 microbar.

... because temperature matters

TR - G 24 The reference pressure used in this article is the long-used and accepted value of 0.0002 microbar. Another way to describe the same value, which may be used in other publications, is the value of 20 x 10-6 Pascals (N/m2). Sound Power Level (Lw) in dB – the measure of the total acoustic power radiated by a given source and is defined by: Lw = 10Log (W/10-12 )dB, reference 10-12 . The standard reference power used in the BAC literature is 10-12 watt. To eliminate any possible confusion, the reference power should always be quoted, as in “a sound power level of 94 dB reference 10-12 watt.” Unit – a single cell of evaporate cooling equipment.

Establishing the Noise Criterion Introduction At the beginning of any sound analysis, it is necessary to establish the sound level at a particular site that would be considered acceptable by those who might be affected. This acceptable sound level is called the “noise criterion” for that situation, and it is important to realize that it may vary widely for different situations. The procedure for developing the noise criterion involves consideration of the following: 1. The type of activity of those people in the vicinity of the evaporative cooling equipment who will be affected 2. The amount of attenuation from acoustic barriers or walls that lie between the equipment and the people who may hear it 3. The outdoor background noise that might help mask the sound from the equipment From these factors, we can arrive at the final noise criterion for the particular installation. The noise that humans hear covers a frequency range of about 20 Hz to about 20,000 Hz. Of course, there are exceptions to this, but this range has come to be accepted for most practical purposes. Furthermore, for most engineering applications, most of this audio range is subdivided into eight frequency bands called “octave bands” which cover the range of frequency somewhat as the octaves on a piano cover the range of pitch. The eight octave bands used in this article have the following identifying center frequencies and ranges: Band Number

Identifying Frequency (Hz)

Approx. Frequency Range (hz)

1

63

44-88

2

125

88-176

3

250

176-353

4

500

353-707

5

1000

707-1414

6

2000

1414-2828

7

4000

2828-5656

8

8000

5656-11312

When sound levels are plotted on a graph, they are most often divided into these eight octave bands. In this way it is possible to observe the variation of a sound level with change in frequency. This variation is important in any situation since humans display a different sensitivity and a different response to low frequency sounds as compared with high frequency sounds. In addition, engineering solutions for low frequency sound issues differ markedly from those for high frequency sound issues.

Indoor Neighbour Activity From earlier studies of real-life situations where people have judged sounds all the way from “comfortable” to “acceptable” to “disturbing” and even to “unacceptable” for various indoor working or living activities, a series of “Noise Criterion Curves” (“NC” curves) has been developed. Figure 1 is a graph of these “NC” curves. Each curve represents an acceptable balance of low frequency to high frequency sound levels for particular situations, and is keyed into the listening conditions associated with the sound. The lower NC curves describe sound levels that are quiet enough for resting or sleeping or for excellent listening conditions, while the upper NC curves describe rather noisy work areas when even conversation becomes difficult and restricted. These curves may be used to set desired sound level goals for almost all typical indoor functional areas where some acoustic need must be served.

Baltimore Aircoil

TR - G 25 Note that the curves of Figure 1 have as their x-axis the eight octave frequency bands; and as their y-axis, sound pressure levels given in decibels (dB) relative to the standard reference pressure of 0.0002 microbar. For convenience, Table 1 lists the sound pressure levels at each octave band center frequency, for each Noise Criterion. Table 1: Octave Band Sound Pressure Levels (dB re 0.0002 microbar) of indoor Noise Criterion (‘NC’) Curves of Figure 1 Octave Band Center Frequency in Hz Noise Criterion 63

125

250

8500

1000

2000

4000

8000

NC-15

47

36

29

22

17

14

12

11

NC-20

51

40

33

26

22

19

17

16

NC-25

54

44

37

31

27

24

22

21

NC-30

57

48

41

35

31

29

28

27

NC-35

60

52

45

40

36

34

33

32

NC-40

64

56

50

45

41

39

38

37

NC-45

67

60

54

49

46

44

43

42

NC-50

71

64

58

54

51

49

48

47

NC-55

74

67

62

58

56

54

53

52

NC-60

77

71

67

63

61

59

58

57

NC-65

80

75

71

68

66

64

63

62

Figure 1 - Noise criterion "NC" Curves. The octave band sound pressure levels associated with the noise criterion conditions of Table 2. Table 2 is used with the NC curves and lists some typical activities that require indoor background sound levels in range of NC-15 to NC-55. Certain unusual acoustical requirements may not easily fall into one of the Table 2 groups. It may be necessary to apply specific criteria for those special situations or to assign a criterion based in similarity to one of the criterion given in the table. It is emphasized that the NC curves are based on, and should be used only for, indoor activity. The first step in the development of the evaporative cooling equipment’s noise criterion is to select from Table 2 the particular activity that best describes what the indoor “neighbors” in the vicinity of the equipment will be doing when the equipment is operating. Where two or more neighbor conditions may be applicable, the one having the lowest NC value should be selected. The corresponding NC values of Figure 1 or Table 1 give the eight octave band sound pressure levels, in decibels, for that selection. The goal is to keep the sound heard by the neighbor, inside his home or building, at or below these sound pressure levels.

... because temperature matters

TR - G 26 Table 2: Suggested Schedule of Noise Criteria for Indoor Neighbour Activities* SUGGESTED RANGE OF NOISE CRITERIA

ACTIVITY Sleeping, Resting, Relaxing Homes, apartments, hotels, hospitals, etc. Suburban and rural Urban

NC-20 to NC-25 NC-25 to NC-30

Excellent Listening Conditions Required Concert Halls, recording studios, etc.

NC-15 to NC-20

Very Good Listening Conditions Required Auditoriums, theaters Large meeting and conference rooms

NC-20 to NC-25 NC-25 to NC-30

Good Listening Conditions Required Private offices, school classrooms, libraries, small conference rooms, radio and television listening in the home, etc.

NC-30 to NC-35

Fair Listening Conditions Desired Large offices, restaurants, retail shops, and stores, etc.

NC-35 to NC-40

Moderately Fair Listening Conditions Acceptable Bussiness machine areas, lobbies, cafeterias, laboratory work areas, drafting rooms, satisfactory telephone use, etc.

NC-40 to NC-45

Acceptable Working Conditions with Minimum Speech Interference Light to heavy machinery spaces, industrial areas, commercial areas such as garages, kitchens, laundries, etc.

NC-45 to NC-55

Note: * The ASHRAE Guide usually lists a 10 dB range of NC values for each situation leaving it to the option of the user to select the specific NC value for his own need. In the interest of more assuredly achieving satisfactory neighbour conditions, Table 2 listings are the more conservative lower 5 dB range of the ASHRAE value.

Sound Reduction Provided by Building Construction Neighbors who are either indoors in their own building or outdoors on their property may hear sound from outdoor equipment. If they are outdoors, they may judge the sound against the more-or-less steady background sounds in the area. If they are indoors, they may tend to judge the sound by whether it is audible or identifiable or intrusive into the surroundings. When outdoor sound passes into a building, it suffers some reduction, even if the building has open windows. The actual amount of sound reduction depends on building construction, orientation, wall area, window area, open window area, interior acoustic absorption, and possibly some other factors. The approximate sound reduction values provided by several typical building constructions are given in Table 3. For convenience in identification, the listed wall constructions are labeled with letters A through G and are described in the notes under Table 3. Note that A represents no wall, hence no sound reduction, and the use of A indicates that the selected NC curve would actually apply in this special case to an outdoor activity, such as for a screened-in porch, an outdoor restaurant, or an outdoor terrace. By selecting the wall construction in Table 3 which most nearly represents that of the building containing the neighbor activity, and adding the amounts of sound reduction from Table 3 to the indoor NC curves, band-by-band, the outdoor sound pressure levels that would yield the desired indoor NC values when the equipment sound passes through the wall and comes inside, are obtained. This second step, then, provides a “tentative outdoor noise criterion” based on hearing the sound indoors in the neighbor’s building. Table 3: Approximate Sound Reduction (in dB) Provided by Typical Exterior Wall Construction Octave Frequency Band

Wall Type (See Notes Below)

(Hz)

A

B

C

D

E

F

G

63

0

10

13

19

14

24

32

125

0

10

14

20

20

25

34

250

0

10

15

22

26

27

36

500

0

10

16

24

28

30

38

Baltimore Aircoil

TR - G 27

Octave Frequency Band

Wall Type (See Notes Below)

(Hz)

A

B

C

D

E

F

G

1000

0

10

17

26

29

33

42

2000

0

10

18

28

30

38

48

4000

0

10

19

30

31

43

53

8000

0

10

20

30

33

48

58

A: No wall; outside conditions B: Any typical wall construction, with open windows covering about 5% of exterior wall area C: Any typical wall construction, with small open-air vents of about 1% of exterior wall area, all windows closed D: Any typical wall construction, with closed but operable windows covering about 10%-20% of exterior wall area E: Sealed glass wall construction, 6 mm thickness over approximately 50% of exterior wall area F: Approximately 100 kg/m2 solid wall construction with no windows and no cracks or openings G: Approximately 250 kg/m2 solid wall construction with no windows and no cracks or openings

Outdoor Background Sound In a relative noisy outdoor area, it is possible that the outdoor background sound is even higher than the “tentative outdoor noise criterion.” In this case, the steady background sound in the area may mask the sound from the evaporative cooling equipment and take over as the controlling outdoor noise criterion. Determining whether or not this situation does exist is the third step in developing the noise criterion. The best way to judge this is to take a few sound pressure level measurements to get the average minimum background level during the quietest intervals in which the equipment is expected to operate, or during the intervals when noise complaints are most likely to be caused; for example, at night in residential areas where cooling equipment is operating at night, or during the day in office areas exposed to daytime cooling equipment sound. In the event that background sound measurements cannot be made, Tables 4 and 5, and Figure 2 may be used to estimate the approximate outdoor background noise. In Table 4, the condition should be determined that most nearly describes the community area or the traffic activity in the vicinity of the evaporative cooling equipment during the quietest time that the equipment will operate. For the condition selected, there is a curve in Figure 2 that gives an estimate of the average minimum outdoor background sound pressure levels. The sound pressure levels of the Figure 2 curves are also listed in Table 5. It is cautioned that these estimates should be used only as approximations of background sounds, and that local conditions can give rise to a wide range of actual sound levels. Table 4: Estimate of Outdoor Background Sounds Based on General Type of Community Area and Nearby Automotive Traffic Activity CONDITION

CURVE No in FIGURE 2 or TABLE 5

1. Nighttime, rural; no nearby traffic of concern 2. Daytime, rural; no nearby traffic of concern

1 2

3. Nighttime, suburban; no nearby traffic of concern 4. Daytime, suburban; no nearby traffic of concern

2 3

5. Nighttime, urban; no nearby traffic of concern 6. Daytime, urban; no nearby traffic of concern

3 4

7. Nighttime, business or commercial area 8. Daytime, business or commercial area

4 5

9. Nighttime, industrial or manufacturing area 10. Daytime, industrial or manufacturing area

5 6

11. Within 100 m of intermittent light traffic 12. Within 100 m of continuous light traffic

4 5

13. Within 100 m of continuous medium-density traffic 14. Within 100 m of continuous heavy-density traffic

6 7

15. 100 to 300 m from intermittent light traffic 16. 100 to 300 m from continuous light traffic

3 4

... because temperature matters

TR - G 28

CONDITION

CURVE No in FIGURE 2 or TABLE 5

17. 100 to 300 m from continuous medium-density traffic 18. 100 to 300 m from continuous heavy-density traffic

5 6

19. 300 to 600 m from intermittent light traffic 20. 300 to 600 m from continuous light traffic

2 3

21. 300 to 600 m from continuous medium-density traffic 22. 300 to 600 m from continuous heavy-density traffic

4 5

23. 600 to 1200 m from intermittent light traffic 24. 600 to 1200 m from continuous light traffic

1 2

25. 600 to 1200 m from continuous medium-density traffic

3

(Determine the appropriate conditions that seem to best describe the area in question during the time interval that is most critical, i.e., day or night. Then refer to corresponding Curve No. in Figure 2 or Table 5 for average minimum background sound levels to be used in sound analysis. Use lowest Curve No. where several conditions are found to be reasonably appropriate.)

Figure 2 : Approximate average minimum outdoor background sound pressure levels associated with the conditions of table 4.

Baltimore Aircoil

TR - G 29 Table 5: Octave Band Sound Pressure Levels (in dB) of Outdoor Background Noise Curves of Figure 2 OCTAVE BAND CENTER FREQUENCY In Hz

CURVE No. in FIGURE 2

63

125

250

500

1000

2000

4000

8000

1

40

37

32

27

22

18

14

12

2

45

42

37

32

27

23

19

17

3

50

47

42

37

32

28

24

22

4

55

52

47

42

37

33

29

27

5

60

57

52

47

42

38

34

32

6

65

62

57

52

47

43

39

37

7

70

67

62

57

52

48

44

42

Final Noise Criterion The measured or estimated average minimum background sound levels should now be compared, band-by-band, with the “tentative outdoor noise criterion” determined previously. The larger of these values, in each frequency band, now becomes the octave band sound pressure levels that comprise the “final outdoor noise criterion” for the equipment installation. Any new intruding sound is generally judged in comparison with the background sound that was already there. If the new sound stands out loudly above the existing sound, the neighbors will notice it, be disturbed by it, and object to it. On the other hand, if the new sound can hardly be heard in the presence of the old sound, it will pass relatively unnoticed. Therefore, if the sound coming from the equipment is below or just equal to the final noise criterion, it will not be noticed and our objectives will have been satisfied. If there are two or more different criterion for a particular installation, the analysis should be carried out for each situation and the lowest final criterion should be used.

Municipal Codes and Ordinances Where local sound codes or ordinances exist, it is necessary to check the expected sound levels of the unit to be installed, including any sound control treatments, to determine if they comply with the code requirements. Depending on the form and language of the code, it may be necessary to introduce the code sound levels into the noise criterion analysis.

Example To summarize this procedure, consider a cooling tower installation located near the edge of a college campus, approximately 91 m from a classroom building. The college is located within a large city, and two main streets pass by one corner of the campus about 450 m from the classroom building. The cooling tower will be used both day and night during warm weather. The classroom must rely on open windows for air circulation. Determine the noise criterion for the cooling tower. The steps for this example are given in the sample Sound Evaluation Work Sheet, included as Appendix D in this article. Step 1 Determine the neighbor activity condition from Table 2. For “good listening conditions” inside a typical classroom, select NC-30 as the noise criterion. Step 2 In the indicated spaces under Item 2 of the Sound Evaluation Work Sheet, enter the sound pressure levels for the octave frequency bands of the NC-30 curve as taken from Figure 1 or Table 1. Step 3 Determine the wall condition of Table 3 that best describes the exterior wall of the classroom. Wall B can be selected for normally open windows during the summer time. Insert the Wall B values in the Item 3 spaces. Step 4 Add the values of Steps 2 and 3 together and insert the sums in the Item 4 spaces. This is the “tentative outdoor noise criterion.” Step 5 In the Item 5 spaces, enter either the measured average minimum background sound pressure levels or the estimated background levels obtained from the use of Figure 2 and Tables 4 and 5. In this example, we estimate that the traffic activity is best represented by “305 m - 610 m from continuous heavy-density traffic.” This leads to Curve 5 of Figure 2 and Table 5, whose values are then inserted in the Item 5 spaces.

... because temperature matters

TR - G 30 Step 6 In the Item 6 spaces insert the higher value, in each frequency band, of either the Item 4 or Item 5 values. This is the “final noise criterion.” In this example, note that the Item 4 values are equal to or higher than the Item 5 values in all bands. Thus, the final noise criterion is based essentially on the classroom noise criterion and the wall condition. However, the outdoor background noise estimate equals the “tentative outdoor noise criterion” in the 250 and 500 Hz bands. If they had been higher, in this example, those higher values would have been used in setting the final noise criterion in those bands. We will attempt to keep all octave band sound pressure levels of the selected cooling tower equal to, or below, the values of Step 6. Should a sound code exist, this would be an appropriate point in the analysis to check agreement between the code and the Step 6 final outdoor noise criterion. If the criterion developed here is lower than the sound code levels at the specified distance, the sound analysis will yield results that will comply with the code. The remaining steps of this sound evaluation example are explained in later sections of this article as we progress with the entire sound evaluation procedure.

Sound Levels for Evaporative Cooling Equipment Introduction Now that we have established an acceptable noise criterion, the next step is to study the source of the sound and develop equipment sound levels at the neighbor location, in the same sound pressure level terms used to express the noise criterion. It will be the aim of this section to discuss the actual sound pressure levels of BAC evaporative cooling equipment, and to show how these levels can be corrected for various distances and certain geometric arrangements. The orientation of the equipment and distance from the equipment to the most “critical neighbor” will be our primary concern. Where possible, the distance from the equipment to the neighbor should be kept as large as possible, and the equipment should be oriented so that its lowest sound levels are radiated toward the neighbor. Evaporative cooling equipment sound ratings can be stated in terms of both sound pressure levels and sound power levels, and both may be necessary to permit thorough sound analysis in a given situation. However, in any sound evaluation, octave band sound pressure levels for the proposed equipment are essential, and it is important to have a fairly accurate indication of the directivity characteristics of the equipment’s sound. For general use, sound pressure levels measured in the four different horizontal directions (one from each side) of the unit, plus the vertical direction above, will yield the desired directivity data. The primary requirements for obtaining the outdoor equipment’s sound levels are: 1. Accurate calibrated sound measurement equipment should be used. 2. Octave band sound pressure levels are mandatory. 3. The sound level data should indicate the true directivity effects of the unit’s sound (there should be no nearby buildings or obstructions to distort the true radiation pattern of the unit test). 4. The measurement distance should be specified. Some equipment is rated in terms of the total sound power radiated, expressed as sound power level. Sound power level is a valid index for comparing the sum of sounds radiated by evaporative cooling equipment, but has the serious disadvantage of not revealing the directivity effects of the radiated sounds. Where only sound power level data are given, the resulting conversion to sound pressure level at a particular location will give less accurate results than if directional sound pressure level data are used. Sound generated by evaporative cooling equipment is directional, and sound pressure level ratings are necessary in order to determine the actual sound in any direction around the installation.

Single Number Rating System Many attempts have been made to express the frequency content and pressure level (intensity) of sounds using a single number system. The most common method used is the A-B-C weighting network of sound level meters. Sound meters with A-B-C weighting networks attempt to simulate the ear’s response to sound at different pressure intensities. At a relatively low sound pressure level, the human ear is considerably more sensitive to high frequency than to low frequency sounds. This difference, however, becomes less noticeable at higher sound levels where the ear approaches more nearly equal sensitivity for low frequency and high frequency sounds. The A-scale weighting network is designed to simulate the ear’s response for low pressure sounds (below about 55 dB). The B-scale weighting is designated to simulate the ear’s response for medium pressure sounds (about 55 dB to 85 dB). The C-scale weighting tends to provide nearly equal response in all frequencies and is used to approximate the ear’s response at higher sound pressure levels (above about 85 dB).

Baltimore Aircoil

TR - G 31

Octave Frequency Band (Hz)

Correction for A weighting

63

-26

125

-16

250

-9

500

-3

1000

0

2000

+1

4000

+1

8000

-1

A-B-C scale ratings have been used in some sound ordinances and equipment sound ratings because of their simplicity of statement. They may have value in some sound comparison situations, but such data are of little value in making an engineering evaluation of a sound issue caused by evaporative cooling equipment, because no indication of the frequency content of the sound is apparent. For example, two different types of cooling towers could have the same A scale rating, but one could have most of its energy in the low frequency bands while the other could have its energy concentrated in the high frequency bands. A single number rating will give no indication of this and its use could lead to less than optimal and sometimes costly decisions.

Comparison of Evaporative Cooling Equipment employing a Centrifugal Fan versus an Axial Fan Based on extensive studies of field data from several cooling tower installations, it has been found that overall sound pressure levels of centrifugal fan cooling towers are about 5 to 7 dB lower than those of axial fan cooling towers for the same cooling capacity even though the axial towers use about half the kW. As a comparison, this means that an axial fan cooling tower would have to be twice as far away from the neighbours as a centrifugal fan tower in order to be just as quiet (6 dB reduction for each doubling of distance, see Table 6). The frequency distribution and the radiation patterns also differ for these two types of units. For any specific comparison of cooling towers, the manufacturer’s actual measured data should be used.

BAC Sound Ratings BAC has measured the sound levels radiated by its products at 1,5 m and 15 m distances for the five principle directions, (four horizontal and one vertical). The sample sound rating data sheet indicates the five principle directions and the type of sound data available for a BAC cooling tower. As the data sheet suggests, the data given in the five blocks pertain to the sound pressure levels measured at 15 m distances from the five principle directions of the cooling tower. Where it might be desired to estimate the sound pressure levels at some intermediate direction, such as halfway between the right end and the air inlet, levels can be averaged or interpolated from the data actually presented. In addition to the five sets of sound pressure levels at each of the two distances, the data sheets contain the calculated sound power level values for the reference power level 10-12 watt. Current sound data for all BAC equipment is available from BAC Balticare Representative. Since sound power levels are being mentioned here, it is appropriate at this point to note that Appendices A, B, and C are given at the end of this article to supply basic information related to sound power levels and to other calculations that may be required from time to time in a sound evaluation. Appendix A describes a simplified method for calculating the sound power level of a unit where the five sets of sound pressure level readings are known. Appendix B gives a procedure for calculating the average sound pressure level at a given distance if the sound power level is known. Appendix C gives a simple procedure for adding decibel values. This is required, for example, in converting sound pressure levels into sound power levels, or in calculating an overall sound pressure level from the eight individual octave band levels, or in adding two or more sound sources.

... because temperature matters

TR - G 32

Effective Distance beyond 15 m In any actual situation, it is usually necessary to determine the sound pressure levels of the equipment at some distance other than the 1,5 m and 15 m distances given in the BAC rating sheets. In this section, distance corrections are given for estimating sound pressure levels at distances beyond 15 m. For distances that are large compared to the dimensions of the unit, the “inverse square law” holds for sound reduction with distance: i.e., for each doubling of distance from the unit, the sound pressure level decreases 6 dB. Thus, for distances beyond 15 m the inverse square law applies and the distance correction is quite straightforward. Table 6 presents the reduction of sound pressure level for distances from 15 m out to 76 m. The values given in Table 6 are to be subtracted from the sound pressure levels at the given distance of 15 m in order to arrive at the sound pressure levels at the distance of interest. For relatively short distances (less than 30 m), the same correction value applies to all eight frequency bands. For the larger distances (greater than 30 m), high frequency sound energy is absorbed in the air and the correction terms have larger values in the high frequency bands. For distances greater than about 150 m, wind and temperature of the air may further influence sound propagation; but because these are variables, they are not considered in this article and the correction figures of Table 6 represent more or less “average” sound propagation conditions. If the critical distance falls between the specific distances given in the left-hand column of Table 6, interpolate the sound reduction value to the nearest 1 dB. Do not attempt to use fractions of decibels.

Baltimore Aircoil

TR - G 33 Table 6: Reduction of Sound Pressure Level (in dB) for Distances beyond 50 feet Octave Band Center Frequency in Hz Distance (m) 63

125

250

500

1000

2000

4000

8000

15

0

0

0

0

0

0

0

0

20

2

2

2

2

2

2

2

2

25

4

4

4

4

4

4

4

4

30

6

6

6

6

6

6

7

7

37,5

8

8

8

8

8

8

9

10

50

10

10

10

10

10

10

11

12

60

12

12

12

12

12

13

14

15

75

14

14

14

14

14

15

16

18

100

16

16

16

16

16

17

18

21

120

18

18

18

18

19

19

21

24

150

20

20

20

20

21

22

24

27

200

22

22

22

22

23

24

27

31

240

24

24

24

25

25

26

30

35

300

26

26

26

27

27

29

34

40

400

28

28

28

29

30

32

38

46

480

30

30

30

31

32

35

43

53

600

32

32

32

33

35

38

47

61

800

34

34

34

36

38

42

53

70

Effect Distance between 1,5 m and 15 m In this section, distance corrections are given for estimating sound pressure levels in the close-in range of 1,5 m to 15 m. When the distance from a sound source is small or comparable to the dimensions of the source, the “inverse square law” does not necessarily hold true for variations of sound level with distance. So, for the relatively short distances of 1,5 m to 15 m, it might be necessary to accept some sound pressure level variations, which do not follow the straightforward trends that hold for distances beyond 15 m. Table 7 permits us to estimate the sound pressure levels at these close-in distances, provided the 1,5 m and 15 m sound pressure levels are known. To illustrate the use of Table 7, suppose the sound pressure level of a unit in a particular frequency band is 68 dB at 1,5 m and 54 dB at 15 m distance. The difference between these two values is 14 dB. In Table 7, we find the column of values under the heading “If the difference between the 1,5 m and 15 m levels is 13 – 15 dB.” The numbers in this column are the values (in decibels) to be added to the 15 m sound pressure level of 54 dB to obtain the sound pressure level at some desired shorter distance. If, for instance, we wish to know the “sound pressure level” of this unit at 1,5 m, we find that we must add 8 dB to the 15 m level of 54 dB to get 62 dB as the sound pressure level at the desired distance of 1,5 m. Now, for these close distances, the difference values between the 1,5 m and 15 m sound pressure levels may not be constant for all frequency bands so it is necessary to follow this procedure for each octave band. For example, in one frequency band the difference may be 12 dB but in another band it may be 15 or 16 dB. Close-in interpolation of sound pressure levels is inherently somewhat unreliable; so do not be surprised if some oddities or discrepancies in the data begin to appear at very close distances. The method used here at least gives some fairly usable data to work with.

... because temperature matters

TR - G 34 Table 7: Interpolation Terms for Obtaining Sound Pressure Levels (in dB) Between 1,5 m and 15 m If the difference between the 5 ft and 50 ft levels is: Distance et which SPL is desired (m))

4-6 dB

7-9 dB

10-12 dB

13-15 dB

16-18 dB

19-21 dB*

22-24 dB

Add the following values to the 15 m sound level to obtain sound level at desired distance: 15

0

0

0

0

0

0

0

13,5

0

0

1

1

1

1

1

12

1

1

1

2

2

2

2

10,5

1

1

2

3

3

3

3

9

2

2

3

4

4

4

5

7,5

2

3

4

5

5

6

7

6

2

4

5

6

7

8

9

4,5

3

5

6

8

9

10

12

3

4

6

8

10

12

14

16

1,5

5

8

11

14

17

20

23

* This column of values is based on the "Inverse Square Law" variation with distance from 15 m all the way in to 1,5 m. All other columns represent variations with distances that do not follow the "Inverse Square Law."

Reflecting Walls and Enclosures Discussion so far has been concerned with what might be considered “simple installations” from an acoustic point of view, where only distance to the neighbor and relative orientation of the unit have been required points of consideration. Frequently, the geometry of an installation involves some nearby reflecting walls or buildings, which adds to the acoustic complexity of the site. Let us consider this for three typical situations:




Cases in which reflecting walls modify the radiation pattern of the sound from the unit to the neighbor Cases in which close-in walls confine the unit and cause a build-up of close-in sound levels Cases in which the unit is located in a well and all the sound radiates from the top of the wall

Effect of Reflecting Walls Several factors that influence the amount of reflected sound are the following: 1. 2. 3. 4. 5. 6. 7.

The sound radiation pattern (directivity) of the equipment The radiating area of the equipment The orientation of the equipment The distance of the unit to the neighbors The distance of the equipment to the reflecting wall The area of the reflecting wall Various angles of incidence and reflection between the equipment, the wall, and the neighbors

Because so many variables are involved, we will not attempt to develop a rigorous procedure for estimating the influence of a reflecting wall. Rather, we caution that if a large reflecting surface is located near the equipment, it should be considered as a potential reflector of sound. If the equipment is oriented such that its loudest side is already facing toward the neighbour, the influence of the reflecting wall can be ignored! However, if this is not the case, these conditions must be met for the reflected sound to be of concern:




The area of the reflecting wall is at least three times the area of the side of the equipment that faces that wall The distance from the unit to the reflecting wall is less than half the distance from the equipment to the neighbor If a simple optical ray diagram is drawn from the center of each unit to all parts of the reflecting wall and the reflecting rays are then drawn away from the wall, the neighbor is located within the angular range of the reflected rays (see sketch below)

If each of these three conditions is met, then the sound pressure levels at the neighbor may be higher than if the wall were not there.

Baltimore Aircoil

TR - G 35

Neighbour Area Influenced by the Reflecting Wall 1. Neighbour area influenced by the reflecting wall; 2. Cooling Tower; 3. Air Intake.

In Figures 3 and 4, a few representative reflecting walls are shown for various orientations, and approximate sound pressure level adjustments are suggested for A, B, C, and D directions away from the equipment. These adjustments should be made using the 15 m levels. Figure 3 applies to units having one air intake, while Figure 4 applies to units having two air intakes. As an example, for Case 1, if the neighbor is located off the A side of the unit, apply the “A” adjustment to the A side 15 m sound pressure level rating of the unit and then correct as necessary to the neighbor’s distance. If the situation is that of Case 9 and the neighbor is located in the direction D, then the “D” adjustment would be utilized to arrive at a 15 m sound pressure level for the unit. Figure 3 : For Single Air Inlet Units

Case 1

Case 2

A. Use Average of A and C Levels, B. Use average of B and C levels, C. Not applicable, D. Use average of D and C levels.

Case 3

A. Not applicable, B. Use greater of B level or average of B and A levels, C. No change to C levels, D. Use greater of D level or average of D and A levels.

Case 4

A. Use greater of A level or average of A and B levels, B. Not applicable, C. No change to C levels, D. Add 2 dB to D levels.

A. Use average of A and C levels, B. Not applicable, C. Not applicable, D. Use average of D and C levels.

... because temperature matters

TR - G 36

Case 5 A. Not applicable, B. Not applicable, C. No change to C levels, D. Use average of A, C, D levels.

Case 6 Four sound levels out the open end of a 3-sided enclosure, add 3 dB to the sound pressure levels of the air intake side of the unit.

Figure 4 : For Dual Air Inlet Units

Case 7 A. Add 2 dB to A levels, B. Use average of B and C levels, C. Not applicable, D. Use average of C and D levels.

Case 8 A. No change to A levels, B. Not applicable, C. No change to C levels, D. Add 3 dB to D levels.

Case 9

Case 10

A. Not applicable, B. Not applicable, C. Add 2 dB to C levels, D. Add 3 dB to D levels.

For sound levels out the open end of a 3-sided enclosure, add 3 dB to the sound pressure levels of the air intake side(s) of the unit.

These figures and their associated adjustment values are to be used to correct base 15 m sound pressure level ratings in the neighbour direction of the effect of the reflecting surface conditions shown. Build-Up of Close-in Sound Levels Evaporative cooling equipment is sometimes located very close to a building wall, inside a “court” formed by two or three surrounding walls, or even in a specially provided room or space in the mechanical equipment area inside a building. In these installations, the principal concern may be the sound in the immediate vicinity (within 1,5 m- 3 m) of the unit(s), rather than the sound levels radiated and reflected away to some neighbor location.

Baltimore Aircoil

TR - G 37 For these situations, we may use Table 7 to determine approximately the sound pressure levels for the close-in distances of interest, and then add an increment to account for the build-up of sound levels. Here also, the geometry of the layout controls the problem and it is not possible to give a general solution that will cover the multitude of possible layouts. As an approximate acknowledgement of this situation, we suggest that the close-in sound pressure levels be increased by 5 dB, recognizing that the range of increase could be as little as 2 or 3 dB (in a fairly open courtyard) and as much as 10 to 15 dB (in a fairly confined mechanical room enclosure). This adjustment should be applied to all eight-octave band readings. Sound Radiation from a Four-Sided Enclosure or "Well" Evaporative cooling equipment is sometimes located inside a four-sided enclosure or “well,” where all the sound radiates more-or-less vertically out the top of the well and then “spills over” the sidewalls of the well. A simple generalized solution to this problem is not possible, but a reasonable approximation can be made. While the sidewalls serve as barrier walls against normal sound radiation in horizontal directions, the four-sided enclosure tends to “average-out” any free-field directional characteristics of the unit and causes an average sound pressure level to be radiated from the top of the well in all directions in which sound is free to radiate per the geometry of the situation. Appendix B provides a procedure for calculating sound pressure levels for a given sound power level, at various distances and with several radiation patterns. In the typical case illustrated, where the sound from the well radiates over a hemisphere, the sound pressure levels of the unit at a 15 m distance would be determined by subtracting 32 dB from the sound power levels of the unit. It should be recognized that this method of sound evaluation is an approximation. Actual sound levels may be somewhat lower in the higher frequency bands, and could be slightly lower in the lower frequency range depending upon the neighbor location relative to the equipment. If the sidewall of the well clearly serves as a barrier wall for the radiated sound, barrier wall attenuation values can be applied to the problem in the same manner as the sound evaluation procedure of this article subsequently permits for the non-well type installation.

Example Continued Let us now summarize Step 2 in the sound evaluation process, looking at the source of sound and correcting it for distance and path. This will yield equipment sound pressure levels for the same point, which the final noise criterion was calculated in the earlier example. We are now interested in Items 7-11 in the sample Sound Evaluation Work Sheet (see Appendix D) which pertain to the cooling tower sound pressure levels as extrapolated to the 90 m distance. We continue the step-by-step procedure on the Sound Evaluation Work Sheet where we left off earlier. Step 7 Decide on the preferred orientation of the cooling tower at the site. From the BAC Sound Rating Data Sheet, determine the sound pressure levels at the 15 m distance for the side of the cooling tower facing the college classroom. Assume one of the end sides here (the “blank-off sides”), since they are the quietest. Insert these sound pressure level values in the Item 7 spaces of the Sound Evaluation Work Sheet. Step 8 Insert the distance “90” m in the appropriate space under Item 8 and refer to Table 6 for the distance correction values corresponding to 90 m. Insert these values in eight spaces of Item 8. Step 9 The sound pressure levels at 90 m will be lower than at 15 m, hence subtract the Item 8 values from the Item 7 values and insert the remainder in the Item 9 spaces. These then are the sound pressure levels that will exist just outside the college classroom, 90 m from the cooling tower. Step 10 Had there been a sound increase due to the presence of a reflecting wall that met one of the conditions illustrated by Figures 3 or 4, corrections would be inserted now in the Item 10 spaces. Had this been a close-in problem involving a build-up of sound levels due to some nearby enclosing walls around the tower, “+5 dB” would have been inserted in the Item 10 spaces. Since neither of these conditions applied in this example, we insert “0” in each of the Item 10 spaces. Step 11 Item 11 is the sum of Items 9 and 10. This is the sound pressure level of the cooling tower at the 90 m distance.

... because temperature matters

TR - G 38

Comparison of Noise Criteria and Evaporative Cooling Equipment Sound Levels Example Continued From the material given in the two preceding sections, it is now possible to determine if a particular cooling tower will be satisfactory (from a sound point-of-view) in a given location for a given set of circumstances. The analysis now consists of comparing the estimated cooling tower sound levels with the noise criterion developed for the neighbor situation. The comparison may be made by plotting the sound levels and the noise criterion on a graph, as show in Figure 5, or merely by comparing the two groups of values on a band-by-band basis. We are now interested in Items 12-13. Step 12 Merely as a means of simplifying the next step, copy in the Item 12 spaces the values taken from Item 6, which was the “Final Noise Criterion.” Step 13 By subtracting the Final Noise Criterion (Item 12) from the Resultant Cooling Tower Sound Pressure Levels (Item 11), we determine if there is any excess of cooling tower sound above the criterion. Any positive-valued remainder represents sound excess above the criterion. Any negative-valued remainder means that the cooling tower level is below the criterion and no sound reduction is required in the frequency bank; hence, “0” is inserted in that space. If the cooling tower levels in all eight octave bands are below the criterion values, there should be no sound problem. If two or three of the cooling tower levels exceed the criterion values by only 1 or 2 or 3 dB, there will probably be no sound problem. If several octave band sound levels exceed the criterion by 5 to 10 dB, or more, a sound problem should be anticipated – the higher the sound excess the more assured is the problem if suitable measures are not taken.

Figure 5 - Comparison of Final Noise Criterion and Equipment Sound Levels

Judgement Factor At this point, some remarks should be made on the overall reliability of this approach, and an opportunity should be provided for inserting a judgment factor. In as much as the original criterion selection was based mostly on lower range NC values for the various environments considered, the derivation presented here may be somewhat conservative. Because of this, decisions based on this approach will usually lead to acceptance of the sound from the equipment. As explained throughout the procedure, several approximations are made (such as for the sound reduction of various general types of walls, and the sound estimates of community or traffic background sounds, and others). These approximations may lead to some variability from one installation to the next, although it is believed that a small amount of variability can be accommodated by the procedure without changing the results unreasonably.

Baltimore Aircoil

TR - G 39 Experience shows that where the criterion is based on sleeping at night, the criterion should not be exceeded, and therefore, the conclusions reached by this procedure should be followed. However, where the criterion is based on somewhat less critical daytime activities, and the background sound frequently ranges considerably above the average minimum conditions used here, then the risk is not too great if the criterion is exceeded by about 5 dB. In such cases the criterion should not be exceeded by more than 5 dB for fear of serious objections. If it is decided to permit the sound to exceed the criterion by as much as 10 dB or more, sound reduction steps should be considered for future addition to the installation, even though they may not be included in the initial installation. In view of the above, if the equipment’s owner, architect or engineer chooses to follow a conservative approach or even to allow for some excess sound on a particular project (that is, permit the equipment’s sound to exceed the background sounds slightly and thus be identifiable and possibly disturbing to the neighbors), this opportunity is afforded in Items 14 and 15 of the Sound Evaluation Work Sheet. Step 14 Insert the cooling tower owner’s Judgment Factor. For a “conservative approach” insert 0 dB in the Item 14 spaces of the Work Sheet. To purposely allow the cooling tower sound to exceed the acceptable levels slightly, insert 5 dB in the Item 14 spaces. Step 15 The Final Sound Reduction Requirement for the cooling tower is the difference, in each band, obtained by subtracting Item 14 from Item 13. These are the attenuation values in each octave band necessary to reduce the cooling tower sound to an acceptable level. A brief discussion of sound control for evaporative cooling equipment is given in the next section. Step 16 Sound reduction can be accomplished in several ways, and quantitative values for possible sound reduction steps are discussed in the next section. Step 16 of the Sound Evaluation Work Sheet should include the attenuation obtained from the use of two-speed fan motors, Baltiguard drives, VFD, low sound fans, barrier walls, and from any special acoustic treatments to be provided. Other situations that may apply are oversizing the equipment and utilizing strategic layout.

Evaporative Cooling Equipment Sound Control Introduction The sound reduction required for evaporative cooling equipment is simply the excess of the equipment’s sound pressure levels over the applicable noise criterion levels. This is shown numerically by the dB values found in Item 15 of the Sound Evaluation Work Sheet when the particular calculation is carried out. The clue as to whether it will be a simple or complex sound reduction problem lies largely in the amount and frequency distribution of the required sound reduction. Job conditions may allow some quieting to be obtained by strategically positioning the equipment, controlling the fan motor, installing a low sound fan option, or constructing barrier walls located between the equipment and neighbor. Additional sound reduction needs may be met with packaged attenuators or other acoustic treatments, which, in general, can achieve high frequency noise reduction rather easily but usually involve larger weight and space requirements to accomplish low frequency quieting.

Strategic Positioning The first and most economical strategy in reducing sound pressure levels from evaporative cooling equipment involves considering the layout of the equipment. “Strategic Positioning” includes two aspects. First, make sure to position the quietest side of the equipment towards the sound sensitive direction. This option should always be a first consideration with single side air inlet products. Next, take advantage of any existing sound barriers that may aid in muffling the sound from the equipment to the neighbor. For example, if a building or shed exists on the job site, position the equipment so that the structure blocks the direct path between the equipment and the neighbor, thus acting as a sound barrier. Trees and bushes are also good examples of barriers that greatly reduce sound exposure at neighboring properties.

Fan Motor Control Operating the equipment at various speeds by utilizing a VFD, Baltiguard drives or a two-speed motor is a practical option of sound control if reduced equipment loads can be made to coincide with periods when low sound pressure levels are required. This is a normal nighttime situation for many air conditioning installations.

... because temperature matters

TR - G 40 An 1500-750 rpm fan motor operating at 750 rpm would provide about 60% of full-load capacity on a BAC unit and would give approximately the following octave band dB noise reductions: Frequency Band - Hz 63

125

250

500

1000

2000

4000

8000

4

6

8

10

8

8

6

4

In as much as these are average dB reductions that can be anticipated for half-speed operation, these figures can apply to both sound power and sound pressure levels. Also, these approximations are sufficiently accurate to be used for both centrifugal and axial fan towers. In addition to running the equipment at a lower speed during noise-critical hours, it is beneficial to investigate whether or not the equipment could be turned off completely during these hours. This would completely negate any sound created by the unit; however, the system and its loads must be researched to understand if this option is feasible. In some cases what people find objectionable is not the steady sound of the equipment, it is the abrupt stopping and starting of the fan system. Properly setting the tower control sequence to avoid excessive cycling of fan motors is important in this regard, as well as to protect the motor from overheating. VFD’s solve this issue by allowing for a soft start of the fans, followed by a gentle ramping up and down of the fan speed in line with the load requirement. Simply stated, VFD's allow the fan motor to run at the speed required to meet leaving water temperature requirements rather than running at full speed all the time. Decreasing the motor speed, and therefore the fan rpm, can decrease sound levels significantly. VFD's also minimize harsh sounding on-off cycles by providing a gradual start.

Figure 7 - If applicable, turn towers off at night to eliminate sound Figure 6 - BAC axial fan cooling tower utilizing the Baltiguard drive.

Figure 8 - VFD with Integrated Bypass

Figure 9 - Axial Fans

Oversizing Equipment If space and budget allow, it may be beneficial to oversize the equipment and run the larger capacity equipment at a lower fan speed rated for the specific job. As discussed in the previous section, reducing the motor speed reduces the fan speed and because fan speed is directly proportional to sound, reduces sound.

Baltimore Aircoil

TR - G 41 Low Sound Fans Another option for reducing the sound that the equipment produces is to select a low sound fan. Low sound fans provide greater solidity than regular fans and so are able to move the same amount of air, while operating at a slower speed.

Barrier Walls Barrier walls can be used to provide sound attenuation. In some cases barrier walls may exist due to the architectural treatment of the site, while at other times they are constructed specifically to provide needed sound reduction. Taking the first case, a wall used to shield a unit from view can also act to reduce the sound radiated by the tower, particularly high frequency sound (broadly considered here as the upper four octave frequency bands). However, such barrier walls must “cover” by line-of-sight the entire sound source as observed from the neighbor’s position. Louvered, latticed or slotted openings will render negligible the attenuation abilities of a barrier wall. A solid wall of height equal to a unit and located close to it will provide the following approximate attenuation: FREQUENCY BAND - Hz 63

125

250

500

1000

2000

4000

8000

4

5

5

5

5

6

7

8

When greater attenuation is required, a larger specially constructed barrier wall may be designed and installed. Care must be taken, though, in locating the wall because of the many geometric and material considerations involved. As an example, a barrier wall that (1) extends at least 1 to 1,5 m beyond the line-of-sight in both the horizontal and vertical directions, (2) that is located within 1,5 to 2,5 m of the cooling tower and (3) that is made of a solid impervious material having a surface weight of at least 85 g/m2 will have approximately the following attenuation: FREQUENCY BAND - Hz 63

125

250

500

1000

2000

4000

8000

5

5

6

8

10

12

14

16

A still larger and heavier barrier wall will provide still greater attenuation. To be most effective, however, a barrier wall must be located as close as possible to the sound source and there must be no reflecting surfaces in the area that can reflect sound around the barrier. Design details of barrier walls and other acoustic treatment such as custom–engineered plenum chambers and acoustic mufflers are best left to acoustical engineers or consultants and acoustical treatment manufacturers.

Figure 10 - Architectural walls being constructed around Closed Circuit Cooling Towers

... because temperature matters

TR - G 42 Sound Attenuation A significant feature of both axial and centrifugal fan equipment is that its noise, if it is a problem at all, can be treated with relatively simple package attenuation. Figure 11 is a photograph of a BAC Series 3000 Cooling Tower (axial fan), with sound attenuation on both the intake and discharge of the unit. The fan intake attenuator is an array of parallel baffles and the discharge treatment is a lined plenum chamber. Lined plenum chambers, to be effective, (1) must be fairly large, (2) should contain a thick absorbent lining, and (3) should be arranged such that the sound path through the plenum includes does not allow line-ofsight. Depending on the degree to which the plenum chamber conforms to these three requirements, its sound reduction may range in the order of 5 to 10 dB for low frequency noise up to 10 to 20 dB for high frequency noise. BAC sound attenuation packages are designed, tested and rated by BAC, hence ensuring single source responsibility. They provide reductions in the horizontal direction up to 25 dB in the mid frequency bands. Many sound attenuation alternatives are available from BAC to optimally and economically meet a large variety of sound requirements. Sound attenuation packages are available for centrifugal and axial fan models. Exact values of the attenuation obtained from these packages are available from your local BAC representative.

Figure 11 - Intake and discharge sound attenuation on a BAC Series 3000 Cooling

Effects of Sound Reduction Options on Equipment Performance The cost of sound attenuation, including the effect on performance, must be evaluated versus simpler methods such as oversizing the unit(s) to meet the sound criteria for a project. Note that with either low sound fans or “add-on” attenuation, lower sound levels often come at the expense of lower airflow. The system designer must ensure that the manufacturer’s ratings are adjusted to account for any decrease in thermal performance from this reduction in airflow. Another caution is for the use of sound barrier walls. It is necessary for barrier walls to be far enough away from the tower so as to prevent recirculation of the moist discharge air. If this practice is not followed, the warm air can be introduced to the air intake, increasing the wet bulb temperature of the unit, and in turn decreasing the cooling capacity of the tower.

Summary This article provides a simple and direct evaluation method for determining whether or not a given evaporative cooling equipment installation is producing, or will produce, excess sound. It also offers some general information on methods that can be used to reduce the sound. BAC can provide reliable sound level data on its open cooling towers, closed-circuit cooling towers, and evaporative condensers through their representatives. Consult your local BAC Balticare Representative for specific project applications. Acknowledgement: BAC extends its sincere appreciation to Mark E. Schaeffer, P.E. (President of Schaffer Acoustics Inc. of Pacific Palisades, CA) for his contributions to this article.

Baltimore Aircoil

TR - G 43

Appendix A The Calculation of Sound Power Level (Lw) from Measured Sound Pressure Levels (Lp) Sound power is a measure of the total acoustic power radiated by a sound source. “Sound power level” is the sound power, expressed in decibels, relative to the reference power quantity 10-12 watt. Sound power is not directly measured as such. Instead, it is a calculated quantity and is obtained from the measurement of sound pressure levels at a suitable number of measurement positions. Even in indoor testing with reverberant or semireverberant rooms and a standard reference sound source, sound power level is calculated from sound pressure level measurements. In this discussion, no technical detail is given for the derivation of sound power level; instead, a very simple procedure is provided for establishing the approximate sound power level of evaporative cooling equipment for the case in which the sound pressure level is measured at four horizontal positions (each position at a specific distance from each of the four sides) plus one vertical position above the unit. The measurement positions may be at any distance between 2 and 4 times the unit’s largest dimension, which is usually its length. The measured sound pressure levels must be obtained with accurate, calibrated equipment, and the sound data must be in the conventional eight octave bands of frequency. The measurements should be made under essentially free-field conditions: i.e., outside in an area free of any nearby reflecting surfaces. The unit is assumed to be located on the ground or on a platform reasonably close to ground level. The approximate sound power level in each of the eight octave bands is the sum, by decibel addition, of the individual five sound pressure level readings in each octave band plus a correction term (K) which is a function of the number of measurements positions, the measurement distance and the reference power. In equation form, this can be expressed as Lw = ∑Lp + K

The decibel summation of a number of sound pressure levels is determined from the material given in Appendix C and the correction terms are given below in Table A for the appropriate conditions. The use of the five measurement positions and the decibel addition of the five readings automatically introduce the directivity characteristics of the unit into the calculated sound power level. No further provision for directivity is required in this simplified method. To illustrate this procedure, suppose we wish to estimate the sound power level (Lw) in one octave band for the case of the five-position measurements 15 m from a cooling tower. Assume the five sound pressure levels measured in the particular frequency band are 56, 53, 59, 53 and 47 dB (re 0.0002 microbar). By the decibel addition method shown in Appendix C we find that the decibel sum of these five sound pressure levels is 62 dB. From Table A we then find that for the 15 m measurement distance, the correction term is 25 dB re 10-12 watt. For this example, Lw = ∑Lp + K = 62 + 25 = 87 dB

The same procedure could be followed for all octave bands to get the complete Lw of the cooling tower. The procedure given here is for the specific five measurement positions noted and may not be applicable generally to other situations. The procedure is not accurate to less than 1 dB, so fractional values of decibels should not be used or relied upon. Correction term K to be used in converting Sound Pressure Levels (Lp) into Sound Power Level (Lw) for special fiveposition procedure given

Table A Measurement Distance (to Acoustic Center) (m)

Correction Term K for Lw re 10-12 Watt (dB)

7,5

19

9

20

10,5

21

12

23

13,5

24

15

25

... because temperature matters

TR - G 44

Measurement Distance (to Acoustic Center) (m)

Correction Term K for Lw re 10-12 Watt (dB)

18,5

26

21

27

24

29

27

30

30

31

Appendix B The Calculation of Average Sound Pressure Level (Lp) for a given Sound Power Level (Lw) For comparative purposes it may occasionally be necessary to estimate the approximate average sound pressure level radiated by a unit for which only the sound power level is given. There are also some applications that are best appraised by converting sound power back to average sound pressure levels. The procedure outlined in this Appendix will provide this estimate. It is important to realize that the resulting value is an average sound pressure level that theoretically would be radiated the same in all directions from the unit. In practice, the unit probably would not radiate the same levels in all directions; but, when only the sound power level is given it is not possible to know the directivity characteristics of the unit. The average sound pressure level at a desired distance is obtained by subtracting from the sound power level in any given octave frequency band the appropriate correction term (C) from Table B. In equation form, this relationship is expressed as Lp Avg. = Lw – C

As an illustration, suppose we wish to know the average sound pressure at a 15 m distance for a cooling tower that is stated to have a sound power level 87 dB re 10-12 watt. (Note that this is the counterpart of the example given in Appendix A.) From Table B, for a 15 m distance, we see that the correction term is 32 dB. Lp Avg. = Lw – C = 87 – 32 = 55 dB

By comparing this value with the five levels fed into the illustration in Appendix A, we see that although this is an average value, it actually does not equal any of the levels from the five measured directions. Note again that the average value does not pretend to show the directivity characteristics of the sound source. If two competitive cooling towers are being compared for a particular site condition, a comparison of the sound power level or the average sound pressure level may be a general clue to the relative sound from the two units, but a more careful comparison should take into account the actual sound levels to be radiated in the particular critical direction(s).

Table B Correction terms C to be used in converting Sound Power Level into average Sound Pressure Level for special fiveposition procedure given. Measurement Distance (to Acoustic Center) (m)

Correction Term K for Lw re 10-12 Watt (dB)

7,5

26

9

27

10,5

28

12

30

13,5

31

15

32

18,5

33

Baltimore Aircoil

TR - G 45

Measurement Distance (to Acoustic Center) (m)

Correction Term K for Lw re 10-12 Watt (dB)

21

34

24

36

27

37

30

38

Note: The correction term C is based on the sound radiating uniformly over a hemisphere. This would apply for a typical ground level installation or for a unit located on a large roof. If there are conditions such that the sound will radiate over a large angle, say a 3/4 sphere, add 3 dB to the above C. Subtract 3 dB from the above C for a 1/4 sphere radiation.

For distance beyond 30 m calculate the average Lp for 15 m using the method here; then extrapolate to the desired distance using the Lp reduction values of table 6 in section "Effect of Distance beyond 15 m"

Appendix C Addition of Decibels Since decibels are logarithmic values it is not proper to add them by normal algebraic addition. For example, 63 dB plus 63 dB does not equal 126 dB but only 66 dB. A very simple, but adequate schedule for adding decibels is as follows: When two decibel values differ by:

Add the following amount to the higher value

0 or 1 dB

3 dB

2 or 3 dB

2 dB

4 to 8 dB

1 dB

9 dB or more

0 dB

When several decibel values are to be added, perform the above operation on any two numbers at a time, the order does not matter. Continue the process until only a single value remains. As an illustration let us add the five sound levels used in the example of Appendix B.

Or, suppose we arrange the same numbers in a different order, as in:

Sometimes, using different orders of adding may yield sums that might differ by 1 dB, but this is not too significant a difference in acoustics. In general, the above simplified summation procedure will yield accurate sums to the nearest 1 dB. This degree of accuracy is considered acceptable in the material given in this article.

... because temperature matters

TR - G 46

Appendix D BAC Sound Evaluation Worksheet Job Name______________________________ Date_____________________________________ Address _______________________________ Engineer ________________________________ Architect ______________________________ BAC Model_________________________________ Items

Center Frequency - Hz 63

125

Step : Noise Criterion 1. Determine appropriate "NC" Criterion for neighbour activity from Table 2 2. Insert sound pressure levels (Lp) for selected "NC" Criterion. (Obtain values from Figure 1 or Table 1) 3. Tabulate sound reduction provided by wall construction. (Obtain values from Table 3) 4. Establish tentative outdoor Noise Criterion for the unit. (Item 2 plus Item 3) 5. List average minimum outdoor background sound levels. (measured or estimated from Figure 2 and Tables 4 and 5) 6. Set final outdoor background Noise Criterion. (High value, by octave band, of Items 4 and 5) Step : Sound Levels 7. Enter unit sound pressure level rating at 15 m. 8. Insert distance correction to adjust unit ratings to distance of _ m in direction toward critical neighbour. (For distance greater than 15 m use Table 6; for distances less than 15 m use Table 7) 9. Establish outdoor unit Lp at neighbour location. (Item 7 minus Item 8 for distances greater than 15 m. Item 7 plus Item 8 for distances less than 15 m. 10. Apply reflection adjustment to meet condition existing at unit site. Refer to Figures 3 and 4 for effect of reflecting walls; or add 5 dB for close-in build up of noise; 0 dB if no reflection effects. 11. Tabulate resultant unit Lp at critical neighbour location. (Item 9 plus Item 10) Step : Comparison, Criteria vs Levels 12. Copy Item 6 levels from above. This is the outdoor noise criterion for the critical neighbour. 13. Ascertain tentative sound reduction required for unit. (Item 11 minus Item 12. Insert "0" for negative values) 14. Apply judgement factor. (For conservative approach, use "0" in all bands. To permit unit noise to exceed background levels slightly , insert "5") 15. Tabulate final sound reduction requirement for the job. (Item 13 minus item 14) 16. Indicate estimated or rated attenuation of all sound reduction treatment if used. (Should at least equal Item 15)

Baltimore Aircoil

250

500

1000

2000

4000

8000

TR - G 47

Motor Controls Introduction The BAC motor control panels, incorporating Variable Frequency Drives (VFD), are specially designed seamlessly with BAC units and are engineered to meet specific application needs related to evaporative cooling equipment. BAC motor controls offer : Single Source Responsibility: BAC has designed the controls taking into consideration the exact specifications of the fan motor, and providing you with a single source solution. Indoor / Outdoor Applications: BAC offers enclosures with location flexibility; whether in a mechanical equipment room or outdoors next to the equipment.

Keypad Setting

Industrial Grade Components: While satisfying the industry’s demands for a top performance variable frequency drive, the BAC motor controls are hailed as a truly environmentally friendly drive. The careful selection of the latest technology industrial grade components provide full motor protection for the evaporative cooling tower. Easy Installation: The BAC motor control is a compact, minimum maintenance reliable AC3 drive, allowing ease of installation due to the pre-engineered concept. Energy Savings: Evaporative water-cooled systems, whether for comfort cooling or process applications, offer substantial year-round system energy savings compared to air-cooled alternatives. Proper system control is crucial to fully utilising this advantage and operating your system at peak efficiency under all combinations of atmospheric and load conditions. BAC’s technical expertise in this field can show you how saving energy can also save you water when using BAC motor controls for a truly “green” solution.

Construction Details


















Epoxy painted steel cabinet - IP 54 insulation class - Fan cooled with independent thermostat - Anti-condensation heaters - Rain shield for cold/warm weather protection 3-Pole Main Disconnect Switch - Suitable for AC3 operation - Lockable operator handle in “OFF” position - NO / NC contacts for auxiliary control panel Variable Frequency Drive (VFD) - Including EMC filters according EN50081 and EN50082 - Removable keypad with rotary knob - Ready, run and fault indicators - Programmable buttons & lights - Monitors motor speed, actual temperature or set point water temperature. - CE compliance to EN 61800 & EN 20178 - RS 485 communications BAC-TPU-01 Controller - Used as temperature controller / signal converter - Sensor input 0 → 10 Volt BAC Type OT-EMM Sensing Elements - PT 100 element - 0 → 10 Volt output Manual 3 Pole Bypass Switch - Automatic VDF or manual control switch Manual Star-Delta Starter - Bypass operator for manual control of fan motor

... because temperature matters

TR - G 48

Custom Features and Options Variable Frequency Drives (VFD's) VFDs offer many benefits including : 1. Precise leaving fluid temperature control provides a more efficient and durable method to vary airflow compared to fan cycling, fan dampers, or mechanical speed changers. 2. Soft-starts, stops, and smooth accelerations prolong the mechanical system (fans, motors, belts, bearings, etc.) life while reducing maintenance. 3. The soft-start feature minimises start-up noise and smooth acceleration make the tower sound less noticeable to the neighbours.

Typical VFD Arrangement Standard VFD includes an enclosure, 24VDC power supply, control power transformer, main circuit breaker, disconnect switch with lockable operator handle, manual bypass, cooling fan and a detachable, programmable VFD keypad. Circuit Breaker Protection, which allows for quick reset, is standard on all BAC VFDs. The circuit breaker is mechanically linked to the rotary disconnect switch mounted on the front of the panel. User Interface Keypad controls auto modes. temperature, and fault codes.

The multi-monitor display shows fan speed, set point, measured

Fan Drive Controls The BAC motor controls are an energy saving capacity control to close monitor the leaving fluid temperature of your cooling tower. The BAC motor controls are perfect for cooling tower operation where reliability, energy savings and low first cost are critical.

Engineering Specifications Equipment controls (optional) Variable Frequency Drive(s): A variable frequency drive (VFD) shall be provided for each tower. The supplier of the VFD shall be the manufacturer of the evaporative cooling equipment. The VFD shall have a manual bypass, a removable keypad, and a circuit breaker disconnect. Fuse protection will not be accepted. VFD shall be provided in an IP 54 enclosure. The heavy-duty, non-fusible safety disconnect switch shall be provided by the manufacturer of the evaporative cooling equipment. Switch shall be single-throw, 3-pole design. Switch shall have triple padlocking capability and a clear visible On/Off handle A temperature sensor shall be provided with the enclosed controls and a temperature controller shall be provided with the enclosed VFD. Option: A vibration cut-out switch input shall be provided

Note: For availability of the BAC motor controls on a specific product line, contact your local BAC Balticare representative.

Baltimore Aircoil

TR - G 49

Plume Abatement Evaporative Cooling & Plume






Air enters at condition A. Air picks up heat and water in the evaporative fluid cooler ( discharge condition B ). Ambient air serves as heat sink for the discharge air ( line AB ). Intersection of saturation line leads to visible plume. Large intersection area : more plume, small intersection area : less plume.

Note: Plume is the condensation of water vapour and is harmless to the environment.

Condition of the Ambient Air Temperature and relative humidity of the entering air influence the condition of the discharge air. Depending on the entering air condition the discharge air IS NOT ALWAYS 100 % SATURATED.






Dry ambient air : discharge air has low relative humidity and high temperature. Wet ambient air : discharge air has high relative humidity and lower temperature. Warm ambient air : discharge air has lower relative humidity and higher temperature. Cold ambient air : discharge air has higher relative humidity and lower temperature. Discharge air of open cooling towers is generally higher saturated than discharge air of evaporative coil products.

EVALUATION OF PLUME FORMATION REQUIRES: Knowledge of climatic conditions (ambient air) in which the equipment will operate. In depth knowledge of evaporative heat transfer to determine the relative humidity and temperature of discharge air in prevailing climate conditions.

Plume Influencing Factors High humidity of ambient and discharge air enhance plume potential and vice versa. Large temperature difference between discharge and ambient air increases plume potential and vice versa.
High heat load/ air flow ratio provides large temperature difference and high plume potential and vice versa (Typically heat load/ air flow ratio for evaporative coil products is smaller.). Next to equipment selection plume formation is a function of the actual heat load and climatic conditions and needs to be evaluated over a wide band of operating conditions. BAC provides the methodology to make such an evaluation.



Plume Abatement Coils

Large surface area plume abatement coils are installed in the air discharge of the evaporative coil products and piped in series with the “wet” coil. To be effective they must have low air and fluid side pressure drops. This results in:

... because temperature matters

TR - G 50 Significant extension of dry operation capacity. Effective increase of discharge air temperature to reduce / eliminate plume during wet operation.
Additional sensible heat transfer during wet operation which saves water and treatment costs. Plume abatement coil sizing and performance prediction require a thorough evaluation of thermodynamic and airside behaviour as well as an understanding of climate condition influences. BAC can provide properly sized plume abatement coils and accurate performance data.



Capacity Control Strategy Capacity control of the evaporative cooling equipment has a considerable influence on plume formation. No capacity control results in the lowest heat load / air flow ratio and low plume potential. Dual drives ( BALTIGUARD ) and two speed motors result in higher heat load / air flow ratio; acceptable plume elimination is achieved with plume abatement coils.
Modulating capacity control results in highest heat load / air flow ratio which gives the highest plume potential. Operating and capacity control strategies are an integral part of the plume evaluation process. Consult your local BAC Balticare Representative for guidance and assistance.



Baltimore Aircoil

TR - G 51

Formulas Fan Laws The fan laws can be used to approximately predict the performance of equipment with a different fan speed: Flow 2 = Flow 1 (kW2/kW1)1/3

Formulas Range = Entering Temperature – Leaving Temperature Approach = Leaving Temperature – Wet Bulb Temperature Heat Rejected: Heat Rejection (kW) = Flow (l/s) x range (°C) x 4,186 Temperature conversions: Fahrenheit to Celsius : Temp (°C) = 0.5556 5temp (°F) – 32 Celsius to Fahrenheit : Temp (°F) = 1.8 Temp (°C) + 32 Basic Electrical: E=IxR E = Voltage (Volts), I= current (amps), R = resistance (Ohm)

... because temperature matters

TR - G 52

Replacement Parts BAC parts are the “Perfect Fit” for your cooling tower. These parts are specifically designed, engineered and manufactured to work in a cooling tower environment. They are the right parts, at competitive pricing levels, and BAC offers the best deliveries in the industry. BAC stocks most common repair and retrofit parts in our Central Parts Distribution Center and can ship other parts, often overnight, from any of three manufacturing facilities strategically located in Europe. Even with this fast delivery capability, it is still recommended that certain essential, emergency repair parts be maintained in your local inventory, to minimize any potential downtime.

Basic Recommended Spare Parts











Bearing set Float valve or repair kit Float ball Solenoid valve (if unit equipped with electronic water level control) Powerband or set of belts Spray nozzle kit with grommets Sump heater and low water cut-out Door gasket Strainer (inlet and suction) Fan and drive bushings

Parts to Consider if Extended Downtime is a Concern






Spray pump for coil products Fan or fan wheels Fan shaft Drive sheaves Fan motor

Baltimore Aircoil

TR - G 53

Application Guidelines Introduction The satisfactory performance of evaporative cooling equipment is dependent on correct selection and proper attention to overall system design, installation, water care and maintenance. The purpose of this document is to highlight the major points, which should be considered when designing a system with BAC evaporative cooling equipment.

Equipment Configurations BAC evaporative cooling equipment is available in following configurations: Cooling Towers

Closed Circuit Cooling Towers

Evaporative Condensers

Counterflow

VXT, VTL, RCT, IMT

VXI, VFL

VXC, VXC-C, VCL

Crossflow

Series 3000D, FXT, TXV FXV, HXI

CXV, HXC

Combined Flow

Thermal Duty The selection of a particular model is based on a thermal duty and the wet bulb temperature. Thermal ratings are based on the wet bulb temperature of the air entering the equipment and do not take into account any recirculation of warm and humid discharge air, which may occur under certain weather and wind conditions. Verification of ratings assumes a test according to a recognised test standard and the application of tolerances as recorded during the test and applied to the test results.

Operating Conditions Cooling Towers

Evaporative. Closed Circuit Cooling Towers

Evaporative . Condensers

Counterflow

Crossflow

Counterflow

Combined Flow

Counterflow

Combined Flow

Design pressure std. coil (bar)

NA

NA

10

10

22

22

Design pressure high press. coil (kPa)

NA

NA

NA

NA

28

28

Spray pressure, max. at inlet (kPa)

50

NA

14

14

14

14

14

19

NA

19

NA

19

Inlet temperature, max. (°C)

55

50

80

60

120

120

Inlet temperature CPVC. max. (°C)

65

58

NA

NA

NA

NA

Inlet temperature, PP, max. (°C)

80

NA

NA

NA

NA

NA

Outlet temperature, min. (°C)

5

5

10

10

-20

-20

100-500

100-500

100-500

100-500

100-500

100-500

fill spacing std(mm)

(1)

Make up pressure mechanical valve (kPa) (2)

(1) BACount® (PVC or CPVC) fill has spacing of 14 mm and is used on all counterflow cooling towers except IMT and RCT. For these product lines fill spacing std. options are 12 mm or 19 mm. Other options are available upon request. PP fill spacings are 12 mm for VXT and VTL and 12 mm or 19 mm for IMT or RCT. (2) It must be ensured that adequate make up water supply is available for proper operation of the equipment within the supply pressure range suitable for the make up valve. Alternative valve selections are available for such cases.

... because temperature matters

TR - G 54

Construction Materials Compatibility Cooling Towers Fill Packing The heat transfer surface is of the film type and compatible with water found in most cooling tower applications. For cooling applications, where the water is contaminated by solids of large size, oil or grease or organic contaminants, alternative heat transfer surfaces with larger spacing must be considered.

Closed Circuit Cooling Towers and Condenser Coils The standard coil is all prime surface continuous serpentine steel tubing. It is designed for low pressure drop with sloping tubes for free drainage. The coil is encased in a steel framework and the entire assembly is hot dip galvanised after fabrication. Fluids circulated through the inside of the coils must be compatible with the coil construction material, i.e. black steel, for std. hot dip galvanised coils stainless steel AISI 304L or 316L (option)
galvanised steel for cleanable coil option (VXI, FXV) Standard coils may contain certain contaminants, such as carbon iron oxide or welding particles. The interior condition of the coil including humid air must be considered, when using halocarbon (or HFC) refrigerants and sensitive system components, such as electronic expansion devices or semi-hermetic compressors. The installer must take the necessary precautions on site, including complete clean up and evacuation and the installation of filter/dryers to safeguard the operation of these components in conjunction with the condenser coils. It is not uncommon that in the first year of operation filter cartridges have to be replaced more frequently.



Water Quality Evaporative cooling is accomplished by the evaporation of a small portion of water. As water evaporates, the dissolved solids originally present in the water remain in the system. The concentration of dissolved solids increases rapidly and can reach unacceptable levels. In addition, airborne impurities and biological contaminants are often introduced into the recirculating water, since the evaporative cooler is washing the air. If impurities and contaminants are not effectively controlled, they can cause scaling, corrosion, sludge or biological fouling, which reduce heat transfer efficiency and increase system operating costs. For optimal heat transfer efficiency and maximum equipment life, the quality of the make-up and recirculating water should be maintained within the limitations listed below.

Make-Up Water Make-up water to the evaporative cooler should be between 30 and 70 ppm hardness as CaCO3. Where use of a softener is necessary to achieve this, the supply to the evaporative cooler should not be totally softened, but blended with the incoming unsoftened water to achieve the minimum hardness between 30 and 70 ppm as Ca CO3. Maintaining a minimum hardness in the make-up water offsets the corrosive properties of totally softened water and reduces the reliance on corrosion inhibitors to protect the system.

Circulating Water Quality (Cycles of Concentration) The quality of the recirculating water is related to the make-up water by the Cycles of Concentration. For example: If a given make-up water had 45 ppm of Chlorides, it would be possible to run the system at 150 / 45 equals 3.33 Cycles of Concentration without exceeding the 150 ppm of Chlorides allowed for a galvanised steel/Zinc Aluminium or Baltiplus unit. Note that this calculation process needs to be repeated for all of the Guideline parameters (Sulphates, Alkalinity, etc), and the lowest resultant Cycles of Concentration used.

Baltimore Aircoil

TR - G 55

Baltiplus Protection pH

7.0 to 9.0

Hardness as (CaCO3)

30 to 500 mg/l

Alkaline as (CaCO3)

500 mg/l max.

Total Dissolved Solids

1000 mg/l max.

Chlorides

125 mg/l max.

Sulfates

125 mg/l max.

Conductivity

1200 µS/m

Chlorination (as free chlorine): continuous

1 mg / l max.

Chlorination (as free chlorine): batch dosing for cleaning & disinfec- 5-15 mg / l max. for 6 hours max. tion

Table 8: Circulated Water Quality Guidelines for Baltiplus Protection

BALTIBOND Corrosion Protection System pH

6.5 to 9.0

Hardness as (CaCO3)

30 to 500 mg/l

Alkaline as (CaCO3)

500 mg/l max.

Total Dissolved Solids

1500 mg/l max.

Chlorides

250 mg/l max.

Sulfates

250 mg/l max.

Conductivity

1800 µS/m

Chlorination (as free chlorine): continuous

2 mg / l max.

Chlorination (as free chlorine): batch dosing for cleaning & disinfec- 5-15 mg / l max. for 6 hours max. tion

Table 9: Circulated Water Quality Guidelines for Baltibond Corrosion Protection System

FRP pH

6.5 to 9.0

Hardness as (CaCO3)

30 to 500 mg/l

Alkaline as (CaCO3)

500 mg/l max.

Total Dissolved Solids

1500 mg/l max.

Chlorides

250 mg/l max.

Sulfates

250 mg/l max.

Conductivity

1800 µS/m

Chlorination (as free chlorine): continuous

2 mg / l max.

Chlorination (as free chlorine): batch dosing for cleaning & disinfec- 5-15 mg / l max. for 6 hours max. tion

Table 10: Circulated Water Quality Guidelines for FRP

... because temperature matters

TR - G 56

pH Hardness as (CaCO3)

SST AISI 304

SST AISI 316

6.5 to 9.0

6.5 to 9.0

50 to 500 mg/l

50 to 500 mg/l

Alkaline as (CaCO3)

500 mg/l max.

500 mg/l max.

Total Dissolved Solids

1500 mg/l max.

1500 mg/l max.

Chlorides

250 mg/l max.

500 mg/l max.

Sulfates

250 mg/l max.

500 mg/l max.

2500 µS/m

2500 µS/m

2 mg / l max.

2 mg / l max.

5-15 mg / l max. for 6 hours max.

5-15 mg / l max. for 6 hours max.

Conductivity Chlorination (as free chlorine): continuous Chlorination (as free chlorine): batch dosing for cleaning & disinfection

Table 11: Circulated Water Quality Guidelines for Stainless Steel

Blow Down To prevent an excessive build-up of impurities in the recirculating water, a small amount of water must be bled from the recirculating water. In many localities, this constant bleed and replacement with fresh make-up water will keep the concentration of impurities in the system at an acceptable level. The Bleed Rate will depend on the Cycles of Concentration required to maintain recirculating water quality and the Evaporation Rate. After the Cycles of Concentration has been determined, the Bleed Rate can be calculated using the following equation: B = E / (N – 1) Where B = Bleed Rate in l/s;

E = Evaporation Rate in l/s;

N = Number of Cycles of Concentration.

The maximum Evaporation Rate can be determined by one of the following 1. 2. 3. 4.

methods:

The Evaporation Rate is approximately 1,8 litres per 1000 kcal of heat rejection. The Evaporation Rate is approximately 1,8 litres per 4180 kJ. Evaporation Rate = Water Flow Rate (I/s) x Range (°C) x 0,0018 Evaporation Rate = Total Heat Rejection kW / 2322 = l/s

Examples : Method n° 2: At a flow rate of 10 I/s and a cooling range of 10 °C the evaporation rate is 0.18 l/s (10 l/s x 10 °C x 0,0018 = 0,18 I/s) Method n° 4: Duty calculates to 418kW, therefore the evaporation rate is 0.18 l/s (418 / 2322 = 0.18 l/s) Note: The calculation method described above should not be used to determine the water consumption of evaporative cooling equipment. Next to heat load and water quality the water consumption depends on climatic conditions, the capacity control strategy and the equipment configuration. Water consumption calculations are therefore complex and therefore should not be based on the maximum evaporation rate, which occurs at dry ambient conditions. The calculation method here is only suitable for the purpose of sizing a proper blow down.

Total Water Make-Up Rate Water Make-up rate = Evaporation Rate + Bleed Rate + Drift Loss The Evaporation and Bleed Rates are calculated as above. Provided the equipment is correctly fitted with well maintained high efficiency drift eliminators (as per standard Baltimore Aircoil supply), the Drift Loss can be considered as insignificant when compared with the Evaporation and Bleed Rates. Note that if other system components require adherence to more stringent recirculating water quality guidelines, the more stringent guidelines must be followed.

Baltimore Aircoil

TR - G 57 Water Treatment The water treatment guidelines below should be followed: 1. Water treatment chemicals or non-chemical systems need to be compatible with the materials of construction used in the cooling system including the evaporative cooling equipment itself. 2. Water treatment chemicals should be added to the recirculating water by an automatic feed system on a continuously metered basis. This will prevent localised high concentrations of chemicals, which may cause corrosion. Preferably the water treatment chemicals should be fed into the cooling system at the discharge of the recirculation pump. The chemicals should not be fed in concentrated form, nor batch fed directly into the cold water sump of the evaporative cooling equipment. 3. Acid water treatment is not recommended. Acid treatment can be considered for open cooling towers furnished with the BALTIBOND® Corrosion Protection or constructed from stainless steel, provided the requirements specified above are followed. 4. A competent water treatment company should be consulted for the specific water treatment programme to be applied. Next to the supply of dosing and control equipment and chemicals, the programme should include regular monthly monitoring of the circulating and make up water quality.

Control of Biological Contamination & Water Treatment The growth of algae, slimes and other micro-organisms, if uncontrolled, will reduce heat transfer efficiency and may contribute to the growth of potentially harmful micro-organisms, such as Legionella, in the recirculating water. Accordingly a treatment programme specifically designed to address biological control should be initiated when the system is first filled with water and administered on a regular base thereafter in accordance with any regulations (national, regional) that may exist or in accordance with accepted codes of good practice, such as EUROVENT 9 - 5 & 6. It is strongly recommended to monitor the bacteriological contamination of the recirculating water on a regular base (for example TAB test with dip slides on a weekly base) and record all results. (TAB = Total Aerobic Bacteria) In addition to the control of biological contamination, which must be done at all times, it may be necessary to install a water treatment regime to prevent the formation of scale or corrosion. To ensure recognition of any risk and the implementation of protective measures, it is recommended to conduct a risk analysis by a specialised risk assessor. It is also recommended to develop an operations plan for the cooling system.

Location Each cooling tower, evaporative cooler or condenser should be located and positioned to prevent the introduction of the discharge air and the associated drift, which may contain contaminants, such as Legionella, into the ventilation systems or open windows of buildings. To yield full thermal performance, equipment location must be chosen in a way that there is unimpeded supply of air to the entire air intake surface. In addition access to all maintenance and inspection points must be safeguarded. Located in enclosures or close to adjoining building walls, the top of the equipment must be level with or higher than the top of the adjacent walls in order to reduce the possibility of recirculating warm and humid discharge air back to the air intake(s). To accomplish this, in some cases the equipment needs to be installed elevated or equipped with discharge hoods or ductwork. In case of elevated locations (more than 300 mm above surface), it is necessary to equip VX equipment with a solid bottom panel, to provide protection from moving parts and ensure that the air is drawn horizontally into the cooling tower and not from the bottom (bottom air entry can be considered but requires reduction of nominal fan speed to avoid fan motor overload). For indoor locations with forced draught centrifugal fan equipment it is common practice to apply ductwork to air entry and discharge. Such ductwork must be designed for even air distribution and minimum pressure drop and access doors must be foreseen to allow access to the interior of the duct and from there to the equipment itself. In some cases the equipment room may be used as an intake plenum, in which case only discharge ductwork is needed. In such cases measures need be taken to prevent erratic air distribution when switching fans and/or cells, for example by the sue of positive closure discharge dampers.

... because temperature matters

TR - G 58

Piping General Piping should be sized and installed in accordance with rules of good practice. Dead legs and stagnant water conditions in the piping should be avoided. If more than one inlet connection is required, balancing valves should be installed to properly balance the flow to each inlet. Depending on the design of the hydraulic circuit, it may also be necessary to install balancing valves at the suction connections of the towers. The use of shut off valves is dictated by the necessity to (automatically or manually) isolate cells or towers for capacity control or servicing. If the equipment is installed on vibration rails, compensators must be installed in the connecting piping.

Open Cooling Towers Since the sump capacity of any cooling tower is limited, it can only accumulate a certain amount of water draining from the system into the tower, when the circulating water pump stops. Therefore install all heat exchangers and as much tower piping as possible below the operating level of the tower. The BAC Balticare Representative can advise the available sump capacity for system drainage for a given model and operating conditions. When multiple cooling towers are used on a common system, install equalising lines between the sumps of the towers to ensure a balanced water level. Standard equalising lines are designed for a maximum water level differential (between sumps) of 25 mm and an equalising flow of 15% of the circulating water flow for the largest tower in the system based on the cooling towers being located in close proximity to each other. The connecting pipework (by others) should maintain the same diameter along their length for proper operation. If hydraulical isolation of individual cells is desired a shut off valve in the equalising piping is needed.

Closed Circuit Cooling Towers Fluid piping should allow flexibility for expansion and contraction between component parts of the system. All fluid piping should be supported separately from the equipment by pipe hangers or supports. In a completely closed system, an expansion tank should be installed for purging air from the system and to allow for fluid expansion. A vacuum breaker or air vent at the high point and a drain at the low point should be installed in the piping system to permit complete drainage of coils.

Evaporative Condensers Refer to BAC Evaporative Condenser Engineering Manual. For installations with high pressure float valves, ensure that liquid piping from condenser outlet to valve(s) is sized for low refrigerant velocity (0.5 m/s) so that valve operation is not disturbed by flash gas and that an equalising line is properly installed. For systems with thermosyphon oil cooling ensure adequate equalising and sufficient height difference between condenser(s) and receiver.

Capacity Control General Most cooling systems are subject to substantial changes in heat load and ambient temperature conditions during the operating season. The capacity of evaporative cooling equipment varies greatly as the wet bulb temperature changes. To prevent freezing inside the equipment at subfreezing ambient conditions and/or when a reasonably constant temperature of the cooling water is desired, some form of capacity control is required. The preferred control method is to reduce the airflow through the equipment to adapt to heat load and ambient conditions. It is not recommended to modulate the water (fluid) flow for capacity control reasons. Regardless the type of capacity control chosen, it is necessary to start the circulating pump first and the fan motor(s) thereafter. At the same time prolonged operation of circulating pump(s) only without fan(s) running should be avoided during subfreezing conditions.

Fan Cycling Fan cycling is the simplest method of capacity control, suitable for multiple cell installations. The number of control steps available for fan cycling is generally determined by the number of fan motors, however on certain models two fan motors must be cycled simultaneously to prevent erratic air distribution. Consult your BAC Balticare Representative for more details. The more steps for fan cycling are available the better the control of the cooling water temperature is. Rapid onoff cycling can cause the fan motor to overheat. It is recommended that controls be set to allow a maximum of 6 on-off starts per hour.

Baltimore Aircoil

TR - G 59 Multi-Speed Drives The number of steps available for fan cycling can be increased by using multi-speed drives. These can either be accomplished by the installation of multi-speed motors (Dahlander/Two speed separate windings) or the BALTIGUARD® Drive system. At half of the nominal fan speed (Dahlander/two speed, separate windings) the nominal capacity of the tower will be appr. 60%; at 2/3 of nominal fan speed (BALTIGUARD) the nominal capacity of the tower will be appr. 70%. When switching from high to low speed a time interval of min. 15 s must be foreseen, before the low speed drive can be activated to allow the fan(s) to slow down.

Modulating Capacity Control Modulating capacity control is recommended when a closer control of the cooling water temperature or condensing pressure is desired and in particular if free cooling at subfreezing ambient conditions is anticipated. Modulating capacity control can be accomplished with modulating fan discharge dampers (only for centrifugal fan models). Fan discharge dampers vary the airflow to match tower capacity to system heat load and ambient condition. The damper motors switch to low speed and shut off the fan motor(s) when the dampers reach minimum position. Alternatively to modulating fan dampers variable speed control devices can be installed. In such cases steps must be taken to avoid operating at or near the fan’s “critical speed”. Consult with the B.A.C. representative or B.A.C. Balticare of any application utilising variable speed control to determine whether any critical speed may be encountered and whether the anticipated fan motor selection is suitable for this application. Fan motors must be equipped with PTC Thermistors for these applications to facilitate protection against motor overheating. Where isolation rails are used in conjunction with variable fan speed controls, the isolation springing should be high deflection, and the minimum continuous running fan speed limited to avoid resonant frequencies with the springing. Modulating capacity control is the best way to closely control cooling water temperatures, however even with modulating control some variation of the cooling water temperature or condensing pressure will occur, in particular at light heat load or start-up conditions. In applications with open or closed circuit cooling towers where such variations cannot be tolerated (start-up of absorption chiller) an additional bypass to stabilise temperatures must be foreseen.

Winter Safety General Unless the system is shut down and drained during winter, measures must be taken to protect the system from freezing during the winter during operation and standstill. Freeze protection during operation is achieved by selecting an adequate method of capacity control. For reasonably constant loads and cooling water or condensing temperatures above 15°C step control is usually adequate. For variable loads, in particular when combined with free cooling modulating controls are recommended. When the equipment is shut down in freezing weather the sump water must be protected. This can be accomplished by the installation of electrical sump heaters. The standard electric heaters are sized to maintain +4°C sump water when the ambient temperature drops to – 18°C. All sump heaters have six power terminals and one earth terminal. Heaters with six terminals can be wired in Star for 400 Volt; 3 phase supply; or in Delta for 230 Volt, 3 phase supply. All heaters can alternatively be used with a 230 Volt single-phase supply, if the terminals are wired in parallel. Sump heaters need to be sized to maintain a sump water temperature of 4°C at an applicable ambient temperature (for example: - 18°C). They are installed together with a heater thermostat and a low level cut out switch to prevent heater operation, when the sump is drained. Draining the sump water into a separate tank installed in an area protected from freezing, is an alternative to auxiliary heating of the integral sump. Remote sump sizing must include the water draining from external piping, the tower water distribution system, water suspended in the fill pack or coil and sump as well as water needed to prevent vortexing inside the remote sump. In addition to the sump all exposed water piping, pumps and make up lines, including mechanical or electrical valves that do not drain at shutdown should be traced with electrical heater tape and insulated.

Closed Circuit CT Coil Protection Where the system will permit, the best protection against coil freeze up is the use of an anti- freeze solution. When this is not possible the system must be designed to meet the following conditions:

... because temperature matters

TR - G 60 1. Maintain the recommended minimum flow (refer to BAC product engineering data) through the coil(s) at all times. 2. Maintain a heat load on the circulating fluid, so that the temperature of the fluid leaving the cooler will not fall below 10°C. (refer to "Engineering Data" for heat loss data) Draining of the coil(s) is not recommended as a normal method of freeze protection unless the coil(s) are constructed from stainless steel or are of the cleanable type. For standard hot dip galvanised coils draining is acceptable as an emergency method of freeze protection. For this purpose an automatic drain valve and air vent needs to be installed to drain the coil(s) if flow stops or the fluid temperature drops below 10°C when the ambient temperature is below freezing.

Plume and Plume Abatement At the air discharge water droplets can be formed by condensation of warm humid discharge air by contact with the colder ambient air upon leaving the equipment. This type of condensation is the visible plume that often can be seen rising above evaporative cooling equipment during the winter season. The water vapour caused by condensation contains droplets of pure water and is harmless. In some instances visible plumes are considered as a hinder, in which case measures must be taken to minimise or eliminate the occurrence of plume. Consult the BAC Balticare Representative for such requests.

Electrical Wiring & Controls Wiring to electrical components should be via suitable weatherproof cable glands. Unused electrical entries should be plugged with a weatherproof plug. Where motors are supplied with PTC Thermistors they should be incorporated into the control circuit as means of motor overheat protection. Also the use of anti condensing heaters is strongly recommended.

Starting of Fan Motors Fan motors up to 5.5 kW nameplate rating can normally be started direct on line 5DOL). Above these ratings the motor should be started using star delta starter and not DOL. DOL starting imposes requires high starting currents and imposes a large staring torque on the fan drives. Alternatively a soft starter or a variable speed frequency drive may be used instead of star delta starting, according to the project requirements. In all cases, precautions should be incorporated into the control circuitry to protect against motor overloading.

Sound BAC provides sound data as sound pressure levels in 5 directions, in 1,5 m and 15 m from the equipment as well as overall sound power levels. Data are available for equipment with and without sound attenuation and should be the base of any acoustical specification and guarantee for outdoor locations. For indoor locations it is preferable to specify partial sound power levels for the air intake and discharge areas. For sound pressure specifications relating to indoor locations, consult the BAC Balticare Representative.

Maintenance Regular maintenance in accordance with the appropriate BAC Operating and Maintenance instructions and with prevailing local regulations and Codes is essential for the efficient and safe operation of a cooling tower, evaporative cooler or condenser. A programme of regular maintenance and inspections needs to be set up, executed and documented. For proper execution of maintenance and inspections and depending on site conditions ladders, safety cages, stairways, access platforms with handrails and toe-boards must be installed as appropriate for the safety and convenience of authorised service and maintenance personnel.

Safety For safe operation of unshielded equipment exposed to wind speeds above 120 km/h installed at a height above 30 m from the ground, contact your local BAC Balticare Representative. For safe operation of equipment installed in moderate and high hazard areas contact your local BAC Balticare representative.

Baltimore Aircoil

TR - G 61

Glossary Air-Conditioning: The control of the temperature, humidity, cleanliness (quality) and movement of air in a confined space. Airflow: The distribution or movement of air through a space; generally measured in cubic feet per minute (cfm). Air Handling Unit: The central component of an HVAC system that distributes conditioned air to a variety of destinations. Algae: Small, usually aquatic plants which require light to grow. Ambient: The surrounding atmosphere. Ambient Air Temperature: The surrounding air temperature, such as the outdoor air temperature around a building. Approach: The difference between the leaving water temperature and the ambient wet-bulb temperature. ARI: Air-Conditioning and Refrigeration Institute. ASHRAE: American Society of Heating, Refrigeration and Air Conditioning Engineers. Biocide: A chemical capable of killing living microorganisms. Biological Contaminants: Living organisms or agents derived from those organisms (e.g., viruses, bacteria, fungi, and mammal and bird antigens) that can be inhaled and can cause many types of health effects including allergicreactions, respiratory disorders, hypersensitivity diseases, and infectious diseases. Also referred to as "microbiologicals" or "microbials.” Bleed: Water deliberately removed from evaporative cooling equipment to control the concentration of dissolved solids in the system. BTU (British Thermal Unit): The amount of heat required to raise or lower the temperature of one pound of water one degree Fahrenheit. BTUH (British Thermal Unit Per Hour): Establishes a time reference to BTU input or output. A BTUH is how many BTUs are used per hour. Bypass Connection: An inlet connection provided in the cold water basin of a unit that allows recirculating water to bypass the heat transfer media when system pumps are running but evaporative cooling is not required. Capacity: The output or producing ability of a piece of equipment. Evaporative cooling capacity is normally referred to in BTUHs; the capacity at a standard set of conditions is often referred to as "tons of cooling." Carryover: Excessive drift. Casing: The exterior panels of an evaporative cooling unit. Cell: The smallest subdivision of a unit that can operate independently; often multiple cells are used together to form one “unit” of a greater capacity. Celsius (C): A temperature scale based on the freezing (0 degrees) and boiling (100 degrees) points of water. Also known as Centigrade. Conversion to Fahrenheit: ºF = 1.8(ºC) + 32 CFM (Cubic Feet per Minute): A standard measurement of airflow that indicates how many cubic feet of air pass by a stationary point in one minute. Charge: The amount of refrigerant placed in a refrigeration unit. Chiller: A device that produces chilled water to provide cooling for HVAC and industrial applications. Circulating Water: See “Reirculating Water.” Cogeneration: Simultaneous production of two or more forms of useable energy from a single fuel source, e.g., heat energy and electrical or mechanical power, in the same facility. Coil: A tube, often including fins, through which gas or liquid is passed, exchanging thermal energy with air or water surrounding it for heating or cooling purposes. Cold Water Basin: The collection pan that houses the cold water processed by the evaporative cooling unit. Combined Flow: The use of both a coil and wet deck surface for heat transfer in a closed circuit cooling tower or evaporative condeser. Combined flow designs reduce evaporation in the coil section. Comfort Cooling: The process of treating air to control its temperature to meet the comfort requirements of the occupants of a conditioned space.

... because temperature matters

TR - G 62 Commercial: The commercial sector is generally defined as non-manufacturing business establishments; this classification includes hotels, restaurants, office buildings, retail stores, educational institutions, etc. Commissioning: The start-up of a building that includes testing and adjusting HVAC, electrical, plumbing, and other systems to assure proper functioning and adherence to design criteria. Commissioning also includes the instruction of operating personnel in the use of the building systems. Compressor: The pump of a refrigerating mechanism that draws a low-pressure gas on the cooling side of the refrigerant cycle and compresses the gas into the high-pressure side of the cycle. The compressor maintains adequate pressure to cause refrigerant to flow in sufficient quantities to meet the cooling requirements of the system. Conduction: The transfer of heat through a solid material. The transfer of heat energy through a material (solid, liquid or gas) by the motion of adjacent atoms and molecules without gross displacement of the particles. Contactor: A switch used to make or break an electrical circuit. Convection: The movement of heat by airflow. Cooling Tower: Any device in which atmospheric air and water are distributed together over a heat transfer medium in order to lower the temperature of the water through evaporative cooling. Corrosion Inhibitors: Chemicals designed to prevent or slow down the waterside corrosion of metals. Counterflow: The flow of air is in the opposite direction of the flow of water. CRN: Canadian Registration Number. This registration is sometimes required on coils shipping into Canada. Crossflow: The flow of air is at a right angle to the direction of the flow of water. CTI: The Cooling Technology Institute (CTI) is an organization comprised of evaporative cooling equipment owners and operators, equipment manufacturers and component suppliers, and water treatment specialists, which advocates and promotes the use of environmentally responsible Evaporative Heat Transfer Systems for the benefit of the public through education, research, standards development, government relations, and technical information exchange. Current: A flow of electrons in an electrical conductor. The strength or rate of flow is generally measured in amperes. Damper: A series of movable plates that can be opened or closed to control the flow of air through a space. Decibel (dB): A decibel describes the relative loudness of a sound. The dimensionless unit of measurement used in noise control. Logarithmically expresses the ratio of sound level to a reference level (0.0002 microbar). Defrost Cycle: The process of removing ice or frost buildup from a piece of equipment during the winter months. Delta (or Delta T or ƒT): A difference in temperature. Often used in the context of the difference between the entering water temperature and the leaving water temperature of a cooling tower or closed circuit cooling tower. Demand (Utility): The rate at which electricity or natural gas is delivered to or by a system, part of a system, or piece of equipment at a given instant or averaged over any designated period of time. Electricity demand is typically expressed in kilowatts. Demand Billing: The electric capacity requirement for which a large user pays. It may be based on the customer's peak demand during the contract year, on a previous maximum or on an agreed minimum. Measured in kilowatts. Demand Charge: The sum to be paid by a large electricity consumer for its peak usage level. Design Conditions: A set of conditions specific to the local climate and expected building usage, used to calculate the cooling load for a building. Dewpoint: The temperature at which air becomes saturated with water and begins to condense, forming a dew. Drift: The water aerosol carried out of an evaporative cooling unit by the discharge air. Drift eliminator: A component of most evaporative cooling units that is designed to remove water droplets from the air passing through it. Dry-Bulb Temperature (DB): The temperature measured by a standard thermometer. A measure of the sensible temperature of air. Efficiency: The ratio of the output to the input of any system. Electric Resistance Heater: A device that produces heat through electric resistance. Energy: Broadly defined, energy is the capability of doing work. In the electric power industry, energy is more narrowly defined as electricity supplied over time, generally expressed in kilowatts.

Baltimore Aircoil

TR - G 63 Energy Management System: A control system designed to regulate the energy consumption of a building by controlling the operation of energy consuming systems, such as the heating, ventilation and air conditioning (HVAC), lighting and water heating systems. Entering Water Temperature (EWT): The temperature of the fluid as it returns to the evaporative cooling equipment from the system heat source. Enthalpy: A thermodynamic function of a system, equivalent to the sum of the internal energy of the system plus the product of its volume multiplied by the pressure exerted on it by its surroundings. Equalizer Connection: A connection in the cold water basin of a unit that allows piping (the piping is called an “equalizer line”) to be run from that unit to the basin of another unit; equalizer lines serve to correct any difference in water levels that may develop during operation. Evaporative Cooling: Cooling accomplished through the exchange of latent heat in the form of evaporation. External Pulldown Volume: The volume of water in any external piping and heat exchangers that will drain back to the unit when the pump is shut down, which is equal to the total pulldown volume minus the water suspended in the unit and its distribution system. External Static Pressure: The pressure imposed on cooling equipment by external sources such as ductwork and sound attenuation. Fahrenheit (F): A temperature scale in which the boiling point of water is 212 degrees and its freezing point is 32 degrees at normal atmospheric pressure. Conversion to Celsius: ºC = (ºF – 32)/1.8 Fan, Axial: An air moving device consisting of impeller blades oriented around a central shaft, usually with an aerodynamic inlet housing; axial fans typically move large volumes of air at low pressures as compared to centrifugal fans for the same fan horsepower. Fan, Centrifugal: An air moving device consisting of impeller blades radially oriented parallel to a central shaft, bound with a rim and hub; centrifugal fans typically move smaller volumes of air than axial fans but at a higher pressure for the same fan horsepower. Fan Coil Unit: A terminal unit that delivers conditioned air directly to the occupied space. Fan Deck: The finished surface adjacent to a horizontally mounted axial fan, sometimes used as a working surface to perform maintenance when the proper safety precautions are taken (handrails, ladder, etc.). Fiberglass Reinforced Polyester (FRP): A non-corrosive composite material comprised of a plastic resin matrix, glass fiber reinforcement and other additives. Fill: See “Wet Deck.” Filtration: The process of separating solids from a liquid by means of a filter media through which only the liquid passes. Flume Box: A short channel that runs between two cooling towers, allowing water to flow from one cold water basin to another; a flume box serves to correct any difference in water levels that may develop during operation and generally has a greater capacity of water flow than an equalizer line. Forced Draft: Refers to the location of the fan(s) on evaporative cooling equipment. On forced draft equipment, the fans are located at the air inlets to “force” or push air through the unit. Fouling: Organic growth or other deposits on heat transfer surfaces causing loss of efficiency. Frequency: The number of cycles that an alternating current moves through in each second. Standard electric utility frequency in the United States is 60 cycles per second (60 Hertz). Full Load Amps (FLA): The current draw of a motor under full load. GPM: Measure of liquid flow rate (Gallons Per Minute). Typically based on U.S. gallons, sometimes clarified as USGPM. Heat Exchanger: A device for the transfer of heat energy from the source to the conveying medium. Heat Pump: A device that is capable of both heating and cooling space, depending on user comfort requirements. Heat pumps are generally individually controlled and therefore a heat pump in one room may be heating, while a heat pump in an adjacent room may be cooling. Heat Transfer: Moving heat from one location to another. Hertz (Hz): A unit of electromagnetic wave frequency that is equal to one cycle per second. Hot Water Basin: The collection pan that houses the hot water in an evaporative cooling unit with a gravity distribution system. Humidity: The amount of moisture in the air. HVAC: Heating, Ventilation and Air Conditioning.

... because temperature matters

TR - G 64 Induced Draft: Refers to the location of the fan(s) on evaporative cooling equipment. On induced draft equipment, the fans are located on the air discharge side of the equipment to “induce” air through the unit. Industrial: The industrial sector is generally defined as manufacturing, construction, mining, agriculture, fishing, and forestry establishments (Standard Industrial Classification [SIC] codes 01-39). Interference: The reintroduction of warm discharge air from one evaporative cooling unit into the air inlet of an adjacent unit. To avoid interference, layout guidelines provided by equipment manufacturers should be closely followed. Inverter: See “Variable Frequency Drive.” ISO 9001: 2000: A comprehensive, internationally recognized standard which is concerned with all aspects of quality management in the design, engineering and manufacturing of a product. Latent Heat: Heat that causes a change in state when added or removed, but does not cause a change in temperature. For example, heat that evaporates a substance from a liquid to a vapor but does not increase its temperature. Leaving Water Temperature (LWT): The temperature of the fluid as it leaves the evaporative cooling equipment to return to the system heat source. Legionella: A genus of bacteria; most species of this genus are capable of causing disease in humans. LD, Legionnaires’ Disease, is a pneumonia like disease caused by one genus of Legionella Life-Cycle Cost: The amount of money required to own, operate and maintain a piece of equipment over its useful life. Load: The demand for services or performance made on a machine or system, i.e. amount of heat rejection required by the evaporative cooling equipment Louver: A series of sloping vanes that allow the entrance of air but prevent the escape of water droplets. Make-Up Water: Water added to the recirculating water to compensate for losses from evaporation and bleed. NEMA: National Electrical Manufacturing Association. Nozzle: A device used for regulating and directing the flow of a fluid. Parts Per Million (PPM): A unit which represents a comparison of mass to mass, volume to volume, mass to volume, etc.; commonly used to represent the concentration of dissolved solids in the recirculating water of evaporative cooling equipment. Plenum: The open area of a crossflow evaporative cooling unit through which air is pulled before being discharged to the atmosphere. Plume: Saturated discharge air that forms a visible cloud over evaporative cooling equipment under certain temperature and humidity conditions. Polyvinyl Chloride (PVC): A polymer of vinyl chloride often used for a heat transfer media surface (film) and piping on factory-assembled evaporative cooling equipment. Power: The rate at which energy is transferred. Electricity for use as energy is also referred to as power. Preventive Maintenance: Regular maintenance implemented to reduce the possibility of sudden or unexpected equipment failures. Pulldown: Water that collects in the cold water basin of a unit when the system pumps shut off. Pump, Spray: A water moving device on a closed circuit cooling tower or evaporative condenser for transporting the spray water from the basin to the water distribution system in order to wet the heat transfer surface. Pump, System: A flow moving device for transporting the fluid to be cooled (water in a cooling tower; water, glycol, or other fluid in the case of a closed circuit cooling tower) to the tower and back to the system in a continuous loop. Range: The difference between the entering water temperature and leaving water temperature of an evaporative cooling unit. See also “Delta.” Recirculating Water: The water being circulated over the coil or fill in an evaporative cooling unit. Recirculation: Situation that occurs when the warm discharge air flows back into the air inlets of the evaporative cooling equipment. To avoid recirculation, layout guidelines provided by equipment manufacturers should be closely followed. Reclaiming: Processing or returning used refrigerant to the manufacturer or processor for disposal or reuse. Refrigerant: A chemical that condenses from a vapor to liquid and, in the process, decreases in temperature. Refrigerant Charge: The amount of refrigerant in a system. Retrofit: Broad term that applies to any change after the original purchase, such as adding equipment or accessories to an existing installation.

Baltimore Aircoil

TR - G 65 Saturation Temperature: Also referred to as the boiling point or the condensing temperature. This is the temperature at which a refrigerant will change state from a liquid to a vapor or vice versa. Scale: The accumulation of solids from the minerals contained in water, most often referred to as hardness deposits, i.e. calcium and magnesium. Scale Inhibitor: Chemical added to water to inhibit formation of scale. Sensible Heat: Heat that causes a change in temperature when added or removed, but does not cause a change in state. Separator: A device which uses centrifugal force to separate particles from a suspension; used to remove sediment from evaporative cooling systems. Setpoint: The temperature to which a thermostat is set to result in a desired heated space temperature. Sound Attenuator: Component used on the air inlet or air discharge of an evaporative cooling unit to reduce airborne noise. Specific Heat: In English units, the quantity of heat, in BTU, needed to raise the temperature of one pound of material one degree Fahrenheit. Strainer: A filter used to remove large, suspended solids from a liquid. Subcooled Liquid: Liquid refrigerant that is cooled below its saturation temperature. Suction Connection: The outlet connection through which leaving water is pumped back to the chiller. Sump: The cold water basin of the evaporative cooling equipment. Superheated Vapor: Refrigerant vapor that is heated above its saturation temperature. Thermal (Energy) Storage: A technology that lowers the amount of electricity needed for comfort conditioning during utility peak load periods. A building’s thermal energy storage system might, for example, use off-peak power to make ice at night, then use the ice for cooling during the day. Thermostat: A temperature control device that consists of a series of sensors and relays that monitor and control the functions of a heating and cooling system. Total Pulldown Volume: The sum of the water suspended within the unit and its distribution system during operation, plus the water in any external piping and heat exchangers draining back to the unit when the pump is shut down. Valve: Any device used to control the flow of a fluid through piping. Variable Frequency Drive (VFD): An electronic device that controls the speed of a motor by controlling the frequency of the voltage supplied to that motor. Also known as an inverter. Wet-Bulb Temperature (WB): The temperature at which water, by evaporating into air, can bring the air to saturation at the same temperature. Wet Deck: A heat transfer surface where air and water interface; also known as fill.

... because temperature matters

© Baltimore Aircoil International nv, 2009 All rights reserved by Baltimore Aircoil International nv No part of this publication may be reproduced, stored or transmitted in any form or by any means whether graphic, electronic or mechanical; including photocopying, recording or any other information storage system, without the prior written permission from Baltimore Aircoil International nv This edition of the EU - Product and Application Handbook was published in Belgium by Baltimore Aircoil International nv Industriepark, Zone A, B-2220 Heist-op-den-Berg Baltimore Aircoil International N.V. has used all reasonable efforts to ensure the data and information contained in this book are as accurate and up to date as possible at the time of publication. However, they make no representation that it is absolutely accurate or complete. Errors and omissions can occasionally occur. Baltimore Aircoil International N.V. does not accept responsibility, and expressly disclaim any liability to any party, for any loss or damage, financial or otherwise, caused by any errors or omissions in this edition of the EU - Product and Application Handbook, whether they result from negligence or any other cause.

Baltimore Aircoil

... because temperature matters

Baltimore Aircoil International nv,Industriepark, 2220 Heist-op-den-Berg, Belgium [email protected] - www.BaltimoreAircoil.com